Checkmate

Select the perfect pump/ram module

for your sealant and adhesive package

CHECK-MATE®

ram and uni-drum™ package selection guide

300469 Rev E CheckMate 06.18.02 12:55 PM Page 1

2 1

11 Premier 80:1 CM 1000

12 Bulldog 12:1 CM 2100

13 King 24:1 CM 2100

14 Premier 39:1 CM 2100

Specialty Resins

Autobody Sealer

300,000 Centipoise

Grease

Silicones

200,000 Centipoise

Polysulfides

50,000 Centipoise

Lithographic Inks

Automotive Epoxy

20,000 Centipoise

Acrylic Caulks

5,000 Centipoise

FLOW RATE gpm (lpm)

2 (7.6) 3 (11.4) 4 (15) 5 (18.9) 6 (22.7) 7 (26.5)

7

8

9

10

11

12

13

14

PUMP SELECTION CHART

SevereDuty™ Rod

Maximizes wear life.

Replaceable Outlet Fitting

Lower repair costs.

New Piston Valve with

Floating Piston Seal

Maximum pressurebalance over a wide

range of materialviscosities.

ReplaceableSeat

Minimizes servicecost.

Floating Priming PlateProvides uniform

flow.

UHMWPE and Teflon™

Vee Packings(All Teflonavailable)Broad materialchemicalcompatibility.

Cast Outlet andInlet HousingImproves structuralintegrity.

Severe DutyCylinderDoubles wear life with abrasive fluids.

Large InternalPortingFor maximummaterial flow.

To select the proper pump for agiven sealant or adhesive material, you must know:

1) Material Viscosity (cps)

2) Material Type (urethane, epoxy, acrylic, silicone, etc.)

3) Flow Rate

After obtaining the above information, use the pump selection chart to find therecommended pump. The chart on the rightgives the air motor name, pressure ratioand lower type.

Check-Mate™ Features

AIR MOTOR RATIO LOWER AIR MOTOR RATIO LOWER AIR MOTOR RATIO LOWER

1 Monark® 23:1 CM 200

2 President® 46:1 CM 200

3 Monark 10:1 CM 450

4 President 20:1 CM 450

5 Senator® 34:1 CM 450

6 Bulldog® 55:1 CM 450

7 Senator 19:1 CM 800

8 Bulldog 31:1 CM 800

9 King® 65:1 CM 800

10 King 50:1 CM 1000

FLUI

D PR

ESSU

RE p

si(b

ar,

MPa

)

6000(41, 408)

5000(350, 35)

4000(276, 28)

3000(207, 21)

2000(138, 14)

1000(69, 28)

0

0 1 (3.8)

1

2

3

4

5

6

Use this chart as a guide only. Contact your local Graco representative for further details.

Teflon® is a registered trademark of Du Pont. Registeredtrademarks mentioned herein are the property of theirrespective owners.

Check-Mate 200

Check-Mate 450

Check-Mate 800

Check-Mate 1000

Check-Mate 2100


3

A B C D E F G

Nozzle Dispense Dispense Fluid Pipe Supply Supplyor Tip Valves Hoses Regulators Manifold Hoses Pumps

• Size, shape • Usage • Viscosity • Viscosity • Volume • Viscosity • Container sizeand type of - Manual • Volume • Pressure • Pressure • Volume • Volumefluid flow - Automatic • Length • Volume • Location • Length • Viscositypattern - Robotic • Pressure • Chemical • Drops • Pressure • Pump location

- Shot • Flexibility compatibility • Chemical • Chemical • Chemical• Pressure • Chemical compatibility compatibility compatibility• Volume compatibility

• Nozzles • Mechanical gun • Steel, SST • Mastic • Steel • Steel, SST • Priming piston• Tips • Pneumatic gun • Pipe JIC regulator • SST • Pipe, JIC • Double ball• Extensions • Nozzle • Flexible hoses • Pressure • Pipe • Flexible hoses • Ram mount• Brushes - Extrusion - Teflon compensating • Tubing - Teflon • 5 g, 55 g wiper

- Spray - Buna valve • Sizes - Buna plates- Length - Nylon - Nylon • Drum empty- Orifice - Moisture-Lok - Moisture-Lok options

• Auto crossover

D

B

A

C

F

G

SYSTEM EXAMPLE

MajorComponents

SelectionFactors

EquipmentOptions

Supply Pump

SupplyHose

Fluid Regulator

E Pipe Manifold

DispenseHoses

DispenseValves

Nozzleor Tip

Ball Valves

ManualFlow Gun

55g King Supply

2

CHECK-MATE™ PUMPS

Use the following pump/ram module chart to select the desired pump package for your specific needs. You must decide:

1) Pressure and flow requirements.

2) Will you be using 5 or 55 gallon (2 or 20 liter) drums of material?

3) What is the material viscosity in cps at the application temperature? This determines the ram type.

4) Do you require carbon steel (CS) or stainless steel (SST) wetted parts? To assist with this critical decision, refer to the following guide:

Which Pump to SelectCarbon steel Butyls, epoxies, PVC, silicones, urethanesStainless steel Acrylics, waterbornes

All Check-Mate pumps have Ultra-High Molecular Weight Polyethylene (UHMWPE) and Teflon (TFE) packings. For urethanes and some silicones, an optional all-Teflon packing kit is available. Contact your local Graco distributor for assistance, if required.

Available wiper materials include: nitrile, EPDM rubber and PVC. Nitrile wipers are the most common for sealant and adhesive materials; however, some end-users prefer PVC for silicone materials.

With the above information, appropriately select the pump/ram module from the chart on page 4.

61/2 in. Dual Post Ram3 in. Dual Post RamSingle Post RamCart-Mounted


CalculationsBead Size Diameter Gallons (Liters) per Feet (Meters) per

in. (mm) 1000 Lineal Ft. Lineal Gallon

1/16 (1.7) 0.16 (0.1) 6000 (1829)3/32 (2.4) 0.36 (0.3) 2700 (823)1/8 (3.2) 0.64 (0.5) 1500 (457)

3/16 (5) 1.44 (1.2) 675 (206)1/4 (6.3) 2.55 (2.1) 375 (114)

5/16 (8.3) 3.98 (3.3) 240 (73)3/8 (9.5) 5.74 (4.8) 165 (50)1/2 (12.7) 10.20 (8.5) 95 (29)5/8 (15.8) 15.92 (13.3) 50 (15)3/4 (19) 22.95 (19.1) 35 (11)

1 (25.4) 40.80 (34) 19 (6)

4

CHECK-MATE PUMPS

5

CALCULATIONSPressure drop or ∆P∆P = .0273 Q V L

D4

Where: P = Pressure drop in psi (bar, MPa)V = Viscosity in poise (PS)D= Diameter in inches (mm)Q= Flow rate in gpm (lpm)L = Length in ft (m)

Other ∆P Considerations:* 0.094 diameter nozzle = 300 psi (21 bar, 2.1 MPa)* Gun drop ∆P

Ultra-Lite® 6000 = 400 psi (28 bar, 2.8 MPa)Ultra-Lite 4000 = 400 psi (28 bar, 2.8 MPa)

* Mastic Regulator ∆P = 400 psi (28 bar, 2.8 MPa)* Straight Swivel 1/2 in.(12.7 mm) = 200 psi (14 bar, 1.4 MPa) * Z Swivel 1/2 in. (12.7 mm) = 200 psi (14 bar, 1.4 MPa)

* Filters = 100-400 psi (7-28 bar, 0.7-2.8 MPa)

Material is 2000 poise (200,000 cps) non-thixotropic acrylic latex sealant. 5 gallon (4.2 liter) pails, one manual gun, 25 ft. x 3/8 in. (7.6 m x 9.5 mm) I.D. hose, 1/4 in. (6.3 mm) bead. The part is 6 in. (152 mm) diameter. Need to do 3 parts per minute. Need swivel at the gun.

• 6 in. (152 mm) diameter to circumference - ∏D or 3.14 x 6 in. (152 mm) = 18.84 in. (479 mm) (total) per part.

• 18.84 in. (479 mm) x 3 (3 parts) = 57 in. (1448 mm) of bead per minute

• Flow rate (gpm/lpm) = Area bead x Length bead = 0.049 in2 (∏r2) x 57 in. (1448mm) = 2.77 in3 =0.01 gpm (231 in3 = 1 gal)

∆P = (0.0273) (0.01) (2000) (25) = 13.65 = 689 PSI(.375) 4 .0198

Nozzle ∆P = 300Ultra-Lite 6000 Flow Gun ∆P = 400Fittings & Swivel ∆P = 400

∆PTotal = ∆PNozzle + ∆PGun + ∆PSwivel + ∆PHose= (300 + 400 + 400 + 689) = 1789 psi (123.4 bar, 12.34 MPa)

From the chart, we selected a 46:1 President with a 3 in. single post ram. Since the material is an acrylic, use SST wetted parts or part no. 231-169. A 46:1 pump at 90 psi of air will produce 4140 psi (46 x 90 psi) of pressure. Calculated pressure loss is only 1789 psi, so this selection will be fine for the application.

Example 1

2100

1000

800

450

200

CART, HYDRAULIC(INCLUDES RAM AND PLATE) INDUCTOR PLATE 3 IN. 3 IN. 3 IN. 6-1/2 IN. 6-1/2 IN.

AND LIFT SINGLE POST DUAL POST DUAL POST DUAL POST DUAL POSTATMOSPHERE BOOST PSI 5.5 PSI 11 PSI 2.8 PSI 16 PSI 36 PSI

0 MPa, 0 BAR 0.4 BAR, 0.04 MPa 1 BAR, 1 MPa .02 BAR, 0.02 MPa 1.1 BAR, .11 MPa 2.5 MPa, 0.25 MPa

VISCOSITY (CPS) 20K TO 300 K 50K TO 1M 500K TO 2M 50K TO 500K 300K TO 2.5M 1.5M TO 5M

Air Motor and Fluid WettedDisplacement Outlet Parts 5 GALLON (20 LITER) PAIL 55 GALLON (200 LITER) DRUMMONARK 23:1 1/2 npt(m) CS 231134 231117up to 0.5 gpm (1.9 lpm) SST 231170 231168

PRESIDENT 46:1 1/2 npt(m) CS 231136 231118up to 0.6 gpm (2.3 lpm) SST 231172 231169

MONARK 10:1 3/4 npt(m) CS 231144 231113 223816up to 1.0 gpm (3.8 lpm)

PRESIDENT 20:1 3/4 npt(m) CS 231146 231111 223817up to 1.2 gpm (4.5 lpm)

SENATOR 34:1 3/4 npt(m) CS 231112 223818up to 1.7 gpm (6.4 lpm) *231166* *224661*

BULLDOG 55:1 3/4 npt(m) CS 231115 918386 223819up to 1.7 gpm (6.4 lpm) *231167* *224662*

BULLDOG 31:1 1 npt(f) CS *237263* 686537up to 2.8 gpm (10.6 lpm) 918371 918552

(w/PVC Wiper) (w/PVC Wiper)

KING 65:1 1 npt(f) CS 918372 236472 918597up to 2.8 gpm (10.6 lpm) (w/PVC Wiper)

918313(w/PVC Wiper)

918314(w/EPDM Wiper)

KING 50:1 1 npt(f) CS 918378 686965 918315up to 3.8 gpm (14.4 lpm) 918379 (w/EPDM Wiper)

(w/PVC Wiper)

SST 918380

PREMIER 80:1 1 npt(f) CS 918316

up

to 3.8 gpm (14.4 lpm) (w/EPDM Wiper)

BULLDOG 12:1 1-1/2 npt(f) CS 235835

up

to 7.5 gpm (28.4 lpm)

KING 24:1 1-1/2 npt(f) CS 235836

up

to 7.5 gpm (28.4 lpm)

PREMIER 39:1 1-1/2 npt(f) CS 918303up to 7.5 gpm (28.4 lpm) (w/PVC Wiper)

* Quiet Air Motor Ram plates have nitrile (Buna-N) wipers unless otherwise noted

CS = zinc-plated carbon steelSST = 303 stainless steel

0


* Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations. 7

55 Gallon (200 liter) with 3 in. Dual Post Ram

970022 Tandem 55:1 Bulldog Ram Pumps (EPDM, tireseal material) with Pneumatic CrossoverIncludes: follower plates, outlet check valvesand supply hoses with shutoff valves

970023 Tandem 55:1 Bulldog Ram Pumps (EPDM, tireseal material) with Electric CrossoverIncludes: follower plates, drum empty lightkit, outlet check valves and supply hoses withshutoff valves

970024 Single 55:1 Bulldog Ram Pump (EPDM, tire sealmaterial) with Pneumatic Low-Level ShutoffIncludes: follower plate, outlet check valveand supply hose with shutoff valve

CHECK-MATE 450 PUMP/RAM PACKAGESFlow rates to 1.2 gpm (4.5 lpm)*

For Check-Mate 450 technical information, see Data Sheet 305-546.

6 * Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations.

Cart-Mounted Single-Post Ram Packages for 5 Gallon (19 liter) Pails

231135 Includes Monark 23:1 pump with carbonsteel lower (222782), 5 gallon (19 liter) ramassembly, air regulator, cart (224137), 3/8 in. npt(mbe) x 25 ft. (7.6 m) nylon-linedhose and extrusion flow gun (207945).

231134 Same as 231135, but without hose or gun.

231171 Includes Monark 23:1 pump with stainlesssteel lower (222839), 5 gallon (19 liter) ramassembly, air regulator, cart (224137), 3/8 in. npt(mbe) x 25 ft. (7.6 m) nylon-linehose and extrusion flow gun (207945).


231137 Includes President 46:1 pump with carbonsteel lower (222783), 5 gallon (19 liter) ramassembly, air regulator, cart (224137), 3/8 in. npt(mbe) x 25 ft. (7.6 m) nylon-linedhose and extrusion flow gun (207945).


231173 Includes President 46:1 pump with stainlesssteel lower (222907), 5 gallon (19 liter) ramassembly, air regulator, cart (224137), 3/8 in. npt(mbe) x 25 ft. (7.6 m) nylon-linedhose and extrusion flow gun (207945).


Stationary Single-Post Ram Packages for5 Gallon (19 liter) Pails

231117 Includes Monark 23:1 pump with carbonsteel lower (222782), 5 gallon (19 liter)single-post ram assembly with air regulatorand ram plate.

231168 Same as 231117 but with Monark 23:1 pumpwith stainless steel lower (222907) instead.

231118 Includes President 46:1 pump with carbonsteel lower (222783), 5 gallon (19 liter)single-post ram assembly with air regulatorand ram plate.

231169 Same as 231118 but with President 46:1 withstainless steel lower (222907) instead.



231134 shown 231136 shown 231117 shown 231118 shown

5 Gallon (19 liter) or 30 liter (8 gallon) with 3 in. Dual Post Ram

970249 Single 55:1 Quiet BulldogIncludes: outlet check valve, 10 ft. (3.05m)outlet hose and ball valve

918386 Single 55:1 Quiet Bulldog 5 gal. Ram Pump(Buna-N wiper)Includes: outlet check valve


* Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations. 98 * Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations.

Dual-Post Ram Packages for 55 Gallon(200 liter) Drums

223816 Includes Monark 10:1 pump (222770) withair regulator, 55 gallon (200 liter) dual-postram with air-regulator, ram plate and drumclamps.

223817 Includes President 20:1 pump (222768) withair regulator, 55 gallon (200 liter) dual-postram with air regulator, ram plate and drumclamps.

223818 Includes Senator 34:1 pump (237492) withair regulator, 55 gallon (200 liter) dual postram with air regulator, ram plate and drumclamps.

223819 Includes Bulldog 55:1 pump (222778) withair regulator, 55 gallon (200 liter) dual postram with air regulator, ram plate and drumclamps.

Cart-Mounted Single-Post Ram Packages for5 Gallon (19 liter) Pails

231144 Includes Monark 10:1 pump (222770) with 5 gallon (19 liter) ram plate. air regulator,and cart (224137).

231146 Includes President 20:1 pump (222768) with 5 gallon (19 liter) ram plate, air regulator,and cart (224137).

CHECK-MATE 450 PUMP/RAM PACKAGES Flow rates to 1.2 gpm (4.5 lpm)*


Stationary Single-Post Ram Packagesfor 5 Gallon (19 liter) Pails

231113 Includes Monark 10:1 pump (222770), 5 gallon (19 liter) ram plate and airregulator.

231111 Includes President 20:1 pump (222768), 5 gallon (19 liter) ram plate and airregulator.

231112 Includes Senator 34:1 pump (222769), 5 gallon (19 liter) ram plate and airregulator.

231115 Includes Bulldog 55:1 pump (222778), 5 gallon (19 liter) ram plate and airregulator.



(233816 shown)

(231144 shown) (231113 shown)




970018 Single 65:1 King Ram Pump/Hose/GunIncludes: follower plate, fluid dispense hose,straight swivel and Ultra-Lite 6000 manualdispense gun with nozzle

970031 Single 65:1 Quiet King Ram PumpIncludes: follower plate, outlet check valveand supply hose with shutoff valve

918372 King 65:1 Ram PumpIncludes: follower plate and air controls

918371 Bulldog 31:1 Ram Pump (SST)Includes: tire plate and air controls

55/5 Gallon (200/20 liter) with 55 Gal. (200 liter) 3 in. Dual Post Ram

970025 Tandem 65:1 King Ram Pumps withPneumatic CrossoverIncludes: 5 gal. (20 liter) follower plates,outlet check valves and supply hoses withshutoff valves

970026 Tandem 65:1 King Ram Pump withElectric CrossoverIncludes: 5 gal. (20 liter) follower plates,drum empty light kit, outlet check valves andsupply hoses with shutoff valves

970027 Single 65:1 King Ram Pumps with Pneumatic Low-Level ShutoffIncludes: 5 gal. (20 liter) follower plate,outlet check valve and supply hose withshutoff valves




55 Gallon (200 liter) with 6.5 in. Dual Post Ram

970086 Tandem 65:1 King Ram Pumps (PVC, tire sealmaterial) with Pneumatic Crossover Includes:follower plates, outlet check valves andsupply hoses with shutoff valves

970088 Single 65:1 King Ram Pump (PVC, tire sealmaterial) with Pneumatic Low-Level ShutoffIncludes: follower plate, outlet check valveand supply hose with shutoff valve

970204 Tandem 65:1 King Ram Pumps (EPDM, tireseal material) with Pneumatic CrossoverIncludes: follower plates, outlet check valvesand supply hoses with shutoff valves

970205 Tandem 65:1 King Ram Pumps (EPDM, tireseal material) with Electric CrossoverIncludes: follower plates, drum empty lightkit, outlet check valves and supply hoseswith shutoff valves

970206 Single 65:1 King Ram Pumps (EPDM, tire sealmaterial) with Pneumatic Low-Level ShutoffIncludes: follower plate, outlet check valveand supply hose with shutoff valve

918313 King 65:1 Ram Pump (PVC, tire seal material)Includes: follower plate and air controls

918314 King 65:1 Ram Pump (EPDM, tire seal material)Includes: follower plate and air controls

918597 King 65:1 Ram Pump (PVC Tire Seal Material)Includes: Quiet air motor


970019 Tandem 65:1 King Ram Pumps (EPDM, tireseal material) with Pneumatic CrossoverIncludes: follower plates, outlet check valvesand supply hoses with shutoff valves

970020 Tandem 65:1 King Ram Pumps (EPDM, tireseal material) with Electric CrossoverIncludes: follower plates, drum empty lightkit, outlet check valves and supply hoses withshutoff valves

970021 Single 65:1 King Ram Pump (EPDM, tire sealmaterial) with Pneumatic Low-Level ShutoffIncludes: follower plate, outlet check valveand supply hose with shutoff valve

970074 Single 65:1 King Ram Pump (EPDM, tire sealmaterial) /Hose/GunIncludes: follower plate, fluid dispense hose,straight swivel and Ultra-Lite 6000 manualdispense gun with nozzle

236472 King 65:1 Ram Pump (EPDM, tire seal material)Includes follower plate and air controls

C59521 King 65:1 Ram Pump (EPDM, tire seal material)Includes: follower plate, check valve kit onpump outlet, enhanced bleed handle andblow off

918552 Bulldog 31:1 Ram Pump (SST)Includes: follower plate and air controls







918303 Premier 39:1 Pump Ram AssemblyIncludes: follower plate, PVC follower seals,ram and motor air control.

235836 King 24:1 and 3 in. Ram AssemblyIncludes: King 24:1 CS Pump, 3 in. dualpost ram, ram and motor control, 55 gallon (200 liter) follower plate, dual Buna-N follower seals.

235835 Bulldog 12:1 and 3 in. Ram AssemblySame as 235836 but with Bulldog 12:1instead of King 24:1.

(918303 shown)

CHECK-MATE 1000 PUMP/RAM PACKAGESFlow rates to 3.7 gpm (14 lpm)*


918315 King 50:1 EPDM plate, air controls

918316 Premier 80:1 EPDM plate, air controls

970187 Single Premier 80:1 Pneumatic Low-Level Shutoff

970185 Tandem Premier 80:1 Pneumatic Crossover


686965 King 50:1


918378 King 50:1 Wiper plate, air controls

918379 King 50:1 PVC tire plate, air controls

918380 King 50:1 SST wiper plate, air controls


(686965 shown)


* Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations. 1514

UNI-DRUM BULK SUPPLY SYSTEMSFlow rates to 2.8 gpm (10.6 lpm) to 4.6 gpm (17.4 lpm)*

56:1 King (with Dura-Flo™ 900 pump lower)Max. outlet pressure: 5000 psi (34.5 MPa, 345 bar)Max. fluid flow @ 60 cpm: 3.4 gpm (13 lpm)C58-607 LH Unit; C58608 RH Unit(Instruction manual 308-353)

970153 Tandem 56:1 King Ram Pumps withPneumatic CrossoverIncludes: follower plates, outlet checkvalves and fluid dispense hoses withshutoff valves

970158 Tandem 56:1 King Ram Pumps withPneumatic Crossover and EnhancedDepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

67:1 Premier (with Dura-Flo 1200 pump lower)Max. outlet pressure: 4690 psi (32.3 MPa, 323 bar)Max. fluid flow @ 60 cpm: 4.6 gpm (17.2 lpm)C58338 LH Unit; C58601 RH Unit(Instruction manual 308-813)

970065 Tandem 67:1 Premier Ram Pumps withPneumatic CrossoverIncludes: follower plates, outlet checkvalves and fluid dispense hoses withshutoff valves

970066 Tandem 67:1 Premier Ram Pumps withPneumatic Crossover and DepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

970154 Tandem 67:1 Premier Ram Pumpswith Pneumatic Crossover and Enhanced DepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

For Uni-Drum technical information, see Data Sheet 305-550.

Physical Dimensions of Ram AssembliesWeight . . . . . . . . . . . . . . . . . . . . . . . . .3000 lbs. (1361 kg)

Ram down . . . . . . . . . . . . . . .76 in. W x 51 in. D x 85 in. H

. . . . . . . . . . . . . . . . . .(193 cm W x 130 cm D x 215 cm H)

Ram up . . . . . . . . . . . . . . . .76 in. W x 51 in. D x 141 in. H

. . . . . . . . . . . . . . . . . .(193 cm W x 130 cm D x 358 cm H)

300 Gallon (1200 Liter) Tote ContainersTote containers: 42.5 in. (107.95 cm) diameter only

CHECK-MATE ACCESSORIESFor Check-Mate packages

5 Gallon (20 Liter) RamsFollower Plate Assemblies

222812 Flat WiperBuna-NFits Check-Mate 200 and 450.

222909 Flat WiperTeflon-coated Buna-N and UHMWPE withSST plate.Fits Check-Mate 200 and 450.

918409 Flat wiperBuna-NStandard plate and valve on blow off.Fits Check-Mate 200 and 450.

237702 Flat WiperBuna-NBare assembly. No check or blow off.Fits Check-Mate 800 and 1000.

C58391 Hose Wiper-type Plate AssemblyPVC hose wiper.

Wiper Kits

C03064 PVC Hose Wiper KitFor C58391.

Double-Post Ram Accessories

918430 Low-level Limit Kit with Beacon Light

918414 Mobile Platform Kit

C31197 Hose Support Kit

918439 Ram Repair Kit

55 Gallon (200 liter) Rams

For 3 in. Ram

918478 Empty Drum Kit, PneumaticWith pump shut-off.

C59519 Auto Drum/Pump Crossover Kit120 volt 50/60Hz.

For 6.5 in. Ram

C32463 Passive Drum-Centering (Saddle) ClampsRequires two.

918395 Heavy-Duty Drum Clamp KitBand latches around drum.

918397 Clam Shell Drum Holder KitFor fiber drums.

918393 Auto Drum Pump Crossover KitAll pneumatic.

918394 Low-level Beacon Kit, 120 VoltIncludes switch, bracket, beacon, cable.

C34220 Hose Support KitLarge spring and bracket for cross beam.

C32451 Vent Hood Collector Kit

Follower Plates

918305 Ram Plate Assembly without Drum Seals

Drum Wiper Kits

C03059 PVC Hose-type

918312 EPDM Hose-type

C03228 Buna-N (Neoprene) Hose-type

165601 White Neoprene Solid Wiper Ring

For Uni-Drum Ram

918241 Follower Plate Scale

918110 Ram Repair Kit


1716 * Maximum flow rates are for comparison purposes only. Consult a qualified Graco distributor for final recommendations.

45:1 Premier (with Dura-Flo 1800 carbon steelpump lower)Max. outlet pressure: 4500 psi (31.0 MPa, 310 bar)Max. fluid flow @ 60 cpm: 6.9 gpm (26 lpm)C59793 LH Unit; C59794 RH Unit

970140 Tandem 45:1 Premier Ram Pumps withPneumatic Crossover and EnhancedDepressurizationIncludes: follower plates, automaticdepressurization, SST pump lowers, outletcheck valves and fluid dispense hoses withshutoff valves

970141 Tandem 45:1 Premier Ram Pumps withPneumatic Crossover Includes: follower plates, automaticdepressurization, SST pump lowers, outletcheck valves and fluid dispense hoses withshutoff valves

45:1 Premier (with Dura-Flo 1800 pump lower)Max. outlet pressure: 4500 psi (31.0 MPa, 310 bar)Max. fluid flow @ 60 cpm: 6.9 gpm (26 lpm)C59778 LH Unit; C59779 RH Unit(Instruction manual 308-147)

970150 Tandem 45:1 Premier Ram Pumps withPneumatic Crossover Includes: follower plates, outlet check valvesand fluid dispense hoses with shutoff valves

970155 Tandem 45:1 Premier Ram Pumps withPneumatic Crossover and EnhancedDepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

34:1 Premier (with Dura-Flo 2400 pump lower)Max. outlet pressure: 3400 psi (23.5 MPa, 235 bar)Max. fluid flow @ 60 cpm: 9.2 gpm (34 lpm)C58461 LH Unit; C58462 RH Unit(Instruction manual 308-151)

970123 Tandem 34:1 Premier Ram Pumps withPneumatic Crossover and EnhancedDepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

970151 Tandem 34:1 Premier Ram Pumps withPneumatic Crossover Includes: follower plates, outlet check valvesand fluid dispense hoses with shutoff valves

20:1 King (with Dura-Flo 2400 pump lower)Max. outlet pressure: 1800 psi (12.6 MPa, 126 bar)Max. fluid flow @ 50 cpm: 7.7 gpm (29.1 lpm)C59784 LH Unit; C59785 RH Unit(Instruction manual 308-151)

970152 Tandem 20:1 King Ram Pumps withPneumatic CrossoverIncludes: follower plates, outlet check valvesand fluid dispense hoses with shutoff valves

970157 Tandem 20:1 King Ram Pumps, Pneumaticwith Crossover and EnhancedDepressurizationIncludes: follower plates, automaticdepressurization, outlet check valves andfluid dispense hoses with shutoff valves

UNI-DRUM BULK SUPPLY SYSTEMSFlow rates to 6.9 gpm (26.1 lpm) to 9.2 gpm (34.8 lpm)*

NOTES

For Uni-Drum technical information, see Data Sheet 305-550.

300 Gallon (1200 Liter) Tote ContainersTote containers: 42.5 in. (107.95 cm) diameter only


ABOUT GRACO

PROVEN QUALITY. LEADING TECHNOLOGY.

Founded in 1926, Graco is a world leader in fluid handling systems and components.Graco products move, measure, control, dispense and apply a wide range of fluids andviscous materials used in vehicle lubrication, commercial and industrial settings.

The company’s success is based on its unwavering commitment to technical excellence,world-class manufacturing and unparalleled customer service. Working closely withqualified distributors, Graco offers systems, products and technology which set thequality standard in a wide range of fluid handling solutions. Graco provides equipmentfor spray finishing, protective coating, paint circulation, lubrication, and dispensingsealants and adhesives, along with power application equipment for the contractorindustry. Graco’s ongoing investment in fluid management and control will continue to provide innovative solutions to a diverse global market.

©2001 Graco Inc. Form No. 300469E 6/01 Printed in U.S.A. All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

Sales/Distribution/Service North AmericaIndustrial Customer Service 800-328-0211FAX 877-340-6427Industrial Product Information/Demonstration1-877-84GRACO (1-877-844-7226)FAX 612-378-3597

Graco Inc. is registered to I.S. EN ISO 9001

GRACO HEADQUARTERS

All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

AMERICAS

MINNESOTAWorldwide HeadquartersGraco Inc.88-11th Avenue N.E.Minneapolis, MN 55413

MAILING ADDRESSP.O. Box 1441Minneapolis, MN 55440-1441Tel 612 623-6000Fax 612 623-6777

MICHIGANAutomotive Headquartersand Sales Office47800 Halyard DrivePlymouth, MI 48170Tel 734 416-3400Fax 734 416-3441

EUROPE

BELGIUMEuropean HeadquartersGraco N.V.Industrieterrein - Oude BundersSlakweidestraat 313630 Maasmechelen, BelgiumTel 32 89 770 700Fax 32 89 770 777

ASIA PACIFIC

JAPANGraco K.K.1-27-12 HayabuchiTsuzuki-kuYokohama City, Japan 2240025Tel 81 45 593 7300Fax 81 45 593 7301

CHINAGraco Hong Kong Ltd.Representative Office Room 118 1st FloorNo. 2 Xin Yuan BuildingNo. 509 Cao Bao RoadShanghai, P.R.China 200233Tel 86 21 649 50088Fax 86 21 649 50077

KOREAGraco Korea Inc.3rd Fl., Doorim Bldg.164-21 Poi-Dong, Kangnam-KuSeoul, Korea 135-260Tel 82 2 575-8901Fax 82 2 571-9422

GRACO INC.P.O. Box 1441Minneapolis, MN 55440-1441

Call today for product information or to request a demonstration.

1.877.84GRACO (1-877-844-7226) or visit us at www.graco.com.

Chec

k-M

ate


Documents

Checkmate