Chart GaraGES Specifications & Prices · Floors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 400mm (14”) centres and covered with 18mm Ply. TiMBer Trea TMeNT

Chart GaraGES Specifications & Prices

Manufacturer of quality Garages, Carriage

Houses, Car Ports and Workshops.

Garden BuildinGs

ContEntSGaraGesspecifications 4

Prices 6

Garages Compare The ranges 7

CarriaGe Houses specifications 9

Prices 10

Car PorTsPrices 11

WorksHoPsspecifications 12

Prices 13

Frequently asked Questions 14

2 01233 229898 [email protected] www.chartgarages.co.ukPlease Note: Timber sizes quoted are sawn dimensions and are slightly smaller after

planing. We reserve the right to alter our specifications without notice.

DElivEry CharGESavon £300 kent Free

Bedfordshire £215 Lancashire DiY

Berkshire £230 Leicestershire £280

Buckinghamshire £205 Lincolnshire Poa

Cambridgeshire £205 London £140

Channel islands DiY Middlesex £160

Cheshire Poa Norfolk Poa

Clywd DiY Northamptonshire £265

Cornwall £560/£860 Northumberland DiY

Cumbria DiY Nottinghamshire £320

Derbyshire £360 oxfordshire £210

Devon Poa Powys DiY

Dorset £295 shropshire £380

Dyfed DiY somerset £350

essex £95/£170 staffordshire £345

Glamorgan – Mid/south DiY suffolk £245

Glamorgan – West DiY surrey Free

Gloucestershire £340 sussex – east Free

Gwent DiY sussex – West £170

Gwynedd DiY Warwickshire £270

Hampshire £185 Wiltshire £290

Herefordshire £320 Worcestershire £320

Hertfordshire £180 Yorkshire – south DiY

Humberside DiY Yorkshire – North DiY

ContaCtS & DeliveryCHarT GaraGes+44 (0)1233 229898

[email protected]

CHarT GarDeN BuiLDiNGs+44 (0)1233 229898

[email protected]

CHarT sTaBLes+44 (0)1233 611123

[email protected]

FeNCiNG saLes oFFiCe+44 (0)1233 626188

[email protected]

UK & European Sales OfficeChart House, Dencora Way, ashford, kent TN23 4FH

For any Garage or Carriage House with an eaves height over 2.5m, (not including the height of the roof), full scaffolding will be required. More photographs are available on our website www.chartgarages.co.uk 3

4 01233 229898 [email protected] www.chartgarages.co.ukPlease Note: Timber sizes quoted are sawn dimensions and are slightly smaller after

planing. We reserve the right to alter our specifications without notice.

THe CLiPPer raNGeWaLL CoNsTruCTioNWalls are built with 75mm x 50mm (3” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGSelected high-quality Shiplap 16mm x 150mm (⅝” x 6”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust-resisting nails. Weatherboard is available as an option.

WaLL LiNiNGan eco-breather membrane to meet the requirements of Bs 4016 Type 2, is placed between the studwork and exterior cladding of all wall panels and doors. Various internal wall linings and insulation are available on request.

rooF CoNsTruCTioNPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, covered with 11mm os Board and black onduline roof sheeting or 38kg green mineral felt. Further options include coloured onduline.

DouBLe DoorsDouble doors are framed, ledged and braced, faced with shiplap. Doors are hung on 450mm adjustable hook and band hinges. Double doors are 2.1m wide x 2.082m high (7’ x 6’ 10”), as standard. Doors will require staining with recognised proprietary stain after installation.

PersoNaL DoorsAre not included as standard but can be fitted as an optional extra.

WiNDoWsare not included as standard. an extensive range of single or double glazed windows are available.

HeiGHT2235mm (7’ 4”) to eaves when on a single course of brickwork. apex height will vary depending upon the width of the building.

GuTTeriNGIs not fitted as standard but can be included as an optional extra.

TiMBer TreaTMeNTall timber is pressure treated adding to the longevity of your building (excluding roof purlins and doors).

THe CHarT raNGeWaLL CoNsTruCTioNWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres and are diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGSelected high-quality Shiplap 16mm x 150mm (⅝” x 6”) pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust-resisting nails. Weatherboard and Loglap are available as options.


rooF CoNsTruCTioNPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, then covered with 11mm os Board and black onduline roof sheeting or 38kg green mineral felt. options include coloured onduline, ondulvilla light weight tiles, or felt tiles.

DouBLe DoorsDouble doors are framed, ledged and braced, faced with shiplap cladding. Doors are hung in a separate door frame, on adjustable hook and band hinges. Doors secured with rim lock and pull handle, lockable from inside and out. Double doors are 2.2m wide x 2.082m high (7’ 6” x 6’ 10”) and side hinged, as standard. Larger and taller double doors are available to suit the eaves height, as well as a range of canopied up & over doors and sliding doors.

PersoNaL Dooras standard your garage will include a single 838mm x 2082mm (2’ 9” x 6’ 10”) personal door, framed, morticed, ledged and braced and faced with shiplap and fitted with a five levered morticed door lock. This door is hung in a separate door frame. inward or outward opening doors are available. all doors are to be treated with a recognised proprietary stain after installation by others.

WiNDoWsare not included as standard. an extensive range of pressure treated single or double glazed windows are available.

HeiGHT2235mm (7’ 4”) to eaves as standard or optional increase to eaves of 2464mm (8’ 1”) when on a single course of brickwork. apex height will vary depending upon the width of the building; please enquire.

GuTTeriNGBlack 100mm (4”) half-round guttering and downpipes are fitted to both sides of the building.

TiMBer TreaTMeNTall timber is pressure treated, adding to the longevity of your building (excluding roof purlins and doors).

GaraGe SPeCifiCationS

all prices exclude VaT. Prices include installation - refer to page 3 for delivery charges

For any Garage or Carriage House with an eaves height over 2.5m, (not including the height of the roof), full scaffolding will be required. More photographs are available on our website www.chartgarages.co.uk 5

THe CHesTer raNGeWaLL CoNsTruCTioNWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres and are diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGselected high-quality shiplap 19mm x 125mm (¾” x 5”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with stainless steel nails. Weatherboard and Loglap are available as options.


rooF CoNsTruCTioNroofs are of a trussed rafter design and manufactured to Bs5268 Part 2 2002, Part 3 2006, Bs6399 Part 1 1996 and Part 2 1997. as standard the roof pitch is 22.5°, boarded with 18mm (¾”) os Boards and covered with onduvilla tiles. Hip roofs are available. The pitch of the trusses can be increased up to 35° to accommodate slate or clay tiles.

soFFiTs aND FasCiaAre fitted as standard and the soffits and fascia are 150mm x 25mm (6” x 1”) and pressure treated.

DouBLe DoorsDouble doors are morticed, ledged and braced framed, rebated and infilled with 19mm x 125mm (¾” x 5”) T.G.V. Doors are hung in a separate heavy-duty frame with 600mm (24”) adjustable hook and band hinges. Doors secured with rim lock and pull handle, lockable from inside and out. Doors are 2286mm wide x 2235mm high (7’ 6” x 7’ 4”) and side hinged, as standard. Larger double doors are available and our Garages can be prepared to take electric up and over doors.

PersoNaL Dooras standard your garage will include a single 915mm x 1981mm (3' x 6’ 6”) personal door hung in a separate door frame with cill. The door is morticed, ledged and braced, rebated and infilled with 19mm x 125mm (¾” x 5”) T.G.V. and fitted with a five levered morticed door lock, inward or outward opening. a range of alternative door sizes are also available.

WiNDoWsare not included as standard. an extensive range of pressure treated, single or double glazed windows are available.

HeiGHT2.505m (8’ 1”) to eaves height when on a single course of brickwork. apex height will vary depending upon the width of the building; please enquire.

GuTTeriNGBlack 100mm (4”) half-round guttering and downpipes are fitted as standard.

TiMBer TreaTMeNTall timber is pressure treated adding to the longevity of your building, (excluding trusses and doors).

sHouLD You WisH To HaVe sLaTe or CLaY TiLes oN Your rooFTo accommodate a range of Clay or slate tiles we increase the pitch of the roof up to a maximum of 35° with specially engineered trusses, VaC VaC treated and manufactured by our truss engineering company to British standard. Please telephone one of our advisors to discuss the preferred option to suit your requirements and locality.

Ga

ra

Ge

s

Please Note: Timber sizes quoted are sawn dimensions and are slightly smaller after planing. We reserve the right to alter our specifications without notice.6 01233 229898 [email protected] www.chartgarages.co.uk


Clipper Chart Chester Chester

3.0m (10') Wide 5.4m x 3.0m (18' x 10') £2,745 £3,650 £5,595 £4,395

7.2m x 3.0m (24' x 10') £3,245 £4,225 £6,750 £5,415

9.1m x 3.0m (30' x 10') £3,995 £5,245 £7,995 £6,325

10.9m x 3.0m (36' x 10') £4,595 £5,765 £9,225 £7,345

12.8m x 3.0m (42' x 10') £5,275 £6,595 £10,445 £8,295

14.6m x 3.0m (48' x 10') £5,825 £7,145 £11,650 £9,295

3.6m (12') Wide 5.4m x 3.6m (18' x 12') £2,845 £3,845 £5,995 £4,815

7.2m x 3.6m (24' x 12') £3,395 £4,375 £7,445 £5,995

9.1m x 3.6m (30' x 12') £4,225 £5,275 £8,845 £6,995

10.9m x 3.6m (36' x 12') £4,755 £5,985 £10,295 £8,155

12.8m x 3.6m (42' x 12') £5,495 £6,895 £11,650 £9,325

14.6m x 3.6m (48' x 12') £5,950 £7,250 £13,115 £10,495

4.2m (14') Wide 5.4m x 4.3m (18' x 14') £3,295 £4,375 £6,395 £5,145

7.2m x 4.3m (24' x 14') £3,825 £4,925 £7,895 £6,315

9.1m x 4.3m (30' x 14') £4,650 £5,695 £9,325 £7,525

10.9m x 4.3m (36' x 14') £5,275 £6,575 £10,885 £8,745

12.8m x 4.3m (42' x 14') £5,995 £7,450 £12,395 £9,875

14.6m x 4.3m (48' x 14') £6,695 £8,115 £13,850 £11,145

4.8m (16') Wide 5.4m x 4.8m (18' x 16') £3,495 £4,650 £7,250 £5,825

7.2m x 4.8m (24' x 16') £4,075 £5,415 £8,950 £6,995

9.1m x 4.8m (30' x 16') £4,925 £5,995 £10,645 £8,450

10.9m x 4.8m (36' x 16') £5,495 £6,925 £12,425 £9,875

12.8m x 4.8m (42' x 16') £6,345 £7,745 £13,575 £10,915

14.6m x 4.8m (48' x 16') £6,975 £8,450 £15,295 £12,245

up to 35° Pitch for a tiled roof

up to 35° Pitch for a tiled roof

For Barn Hips on Chester range Garages and Carriage Houses with roof pitches up to 35° please add...

For Hipped ends on Chester range Garages and Carriage Houses with roof pitches up to 35° please add...

3.0m £295 each

3.6m £345 each

4.2m £415 each

4.8m £475 each

5.4m £545 each

6.1m £595 each

7.3m £715 each

3.0m £1,145 per end

3.6m £1,245 per end

4.2m £1,315 per end

4.8m £1,645 per end

5.4m £1,915 per end

6.1m £2,045 per end

7.3m £2,550 per end

Clipper Chart Chester Chester

5.4m (18') Wide 5.4m x 5.4m (18' x 18') £4,495 £5,815 £8,450 £6,750

7.2m x 5.4m (24' x 18') £4,995 £6,325 £10,215 £8,150

9.1m x 5.4m (30' x 18') £6,345 £7,795 £11,995 £9,695

10.9m x 5.4m (36' x 18') £6,995 £8,450 £13,995 £11,215

12.8m x 5.4m (42' x 18') £8,450 £9,850 £15,995 £12,695

14.6m x 5.4m (48' x 18') £9,195 £10,650 £17,750 £13,395

6.1m (20') Wide 7.2m x 6.1m (24' x 20') £7,475 £10,945 £8,645

9.1m x 6.1m (30' x 20') £9,215 £13,195 £10,615

10.9m x 6.1m (36' x 20') £9,995 £15,375 £12,245

12.8m x 6.1m (42' x 20') £11,650 £17,485 £13,995

14.6m x 6.1m (48' x 20') £12,550 £19,695 £15,845

7.3m (24') Wide 7.2m x 7.3m (24' x 24') £8,095 £12,245 £9,785

9.1m x 7.3m (30' x 24') £9,995 £14,675 £11,655

10.9m x 7.3m (36' x 24') £11,475 £16,995 £13,695

12.8m x 7.3m (42' x 24') £13,415 £19,575 £15,715

14.6m x 7.3m (48' x 24') £14,285 £22,125 £17,595

GaraGe PriCeS

More photographs are available on our website www.chartgarages.co.uk 7

use THis TaBLe To CoMPare THe MaiN FeaTures aCross our GaraGe raNGes

Please do not hesitate

to call 01233 229898 to

discuss the wide range of

optional features we have

available.

Clipper Chart Chester

structurePressure treated timbers externally and internally (not including roof purlins) 2.2m (7’ 4”) to eaves height

Pressure treated timbers externally and internally (not including roof purlins) 2.2m (7’ 4”) to eaves height

Pressure treated timbers externally and internally (excluding trusses) 2.5m (8’ 3”) to eaves height

Framing75mm x 50mm (3” x 2”) prepared timber framing

100mm x 50mm (4” x 2”) prepared timber framing

100mm x 50mm (4” x 2”) prepared timber framing

Linings &

insulation

An eco-breather membrane is placed between the studwork and exterior cladding



Doors &

Frames

2.1m (7’) wide timber double doors, framed ledged and braced

838mm (33”) wide Shiplap faced personal door

2286mm (7’ 6”) double door, morticed, framed, ledged and braced, faced with Shiplap cladding

Rim lock and pull handle, lockable from inside or out, internal tower bolt and drop bolt

All doors hung in door frames

913mm (36”) wide rebated TGV personal door

2286mm (7’6”) double door, morticed, framed, ledged and braced, rebated and infilled with TGV cladding

Rim lock and pull handle, lockable from inside or out, internal tower bolt and drop bolt

All doors hung in door frames

Windows Not included as standard Not included as standard Not included as standard

Guttering Not included as standard Guttering and downpipes Soffits, fascias and guttering

CladdingPressure treated Ex 16mm Shiplap cladding

Pressure treated Ex 16mm Shiplap exterior cladding

Pressure treated Ex 19mm x 125mm Shiplap exterior cladding

roof

Onduline roof underlined with 11mm OS Board

125mm x 50mm (5” x 2”) roof purlins

Onduline roof underlined with 11mm OS Board

125mm x 50mm (5” x 2”) roof purlins

Roof trusses constructed to British Standard

Increased roof pitch to 22.5°, underlined with 18mm OS Board

Onduvilla tiles: red, brown or black

GaraGeS ComPare the ranGeS

cO

mPA

RE

Th

E R

AN

GE

chester carriage house with three open bays.

8 01233 229898 [email protected] www.chartgarages.co.uk


THe CHarT raNGeWaLL CoNsTruCTioNWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGSelected high-quality Shiplap 16mm x 150mm (⅝” x 6”), pressure treated to ensure a long maintenance- free life. Weatherboard and Loglap are available as options. All boarding is fixed with rust resisting nails.

WaLL LiNiNGa traditional eco-breather membrane to meet the requirements of Bs 4016 Type 2 is placed between the studwork and exterior cladding in all wall panels. Various internal wall linings and insulation are available on request.

rooF CoNsTruCTioNPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, covered with 11mm os Board and black onduline roof sheeting or upgrade to our coloured onduvilla light weight tiles or felt tiles. Note that felt tiles are not ideally suited to very exposed areas of the country.

eNTraNCesentrance ways to Carriage Houses have 150mm x 150mm (6” x 6”) pressure treated support posts, framing and 457mm (18”) curved bracing. Doors can be fitted as optional extras.

Doors & WiNDoWsare not included as standard. a wide range of double doors, personal doors and windows are available on request.

HeiGHT2464mm (8’ 1”) to eaves height when on a single course of brickwork. Carriage Houses are also available with an eaves height of up to 2743mm (9’) as an option. apex heights will vary depending upon the width of the building, please enquire.

GuTTeriNGBlack 100mm (4”) half-round guttering and downpipes are fitted to the front and rear.

BarGe BoarDsAll in pressure treated, prepared timber, fixed with rust-resisting nails. Your Carriage House will include a 100mm overhang, underlined, to each gable end.


THe CHesTer raNGeWaLL CoNsTruCTioNWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres.

WaLL CLaDDiNGselected high-quality shiplap 19mm x 125mm (¾”x 5”), pressure treated to ensure a long maintenance-free life. Weatherboard and Loglap are available as options. all boarding is fixed with stainless steel nails.

WaLL LiNiNGa traditional eco-breather membrane to meet the requirements of Bs 4016 Type 2 is placed between the studwork and exterior cladding in all wall panels. Various internal wall linings and insulation are available on request.

rooF CoNsTruCTioNroofs are of a trussed rafter design and manufactured to Bs5268 Part 2 2002, Part 3 2006, Bs6399 Part 1 1996 and Part 2 1997. as standard, the roof pitch is 22.5°, then boarded with 18mm os Board and covered with onduvilla tiles. Gable end roofs or hipped roofs are available. options include onduline or felt tiles or the pitch of the trusses can be increased up to 35° to accommodate slate or clay tiles.

soFFiTs aND FasCiasAre fitted as standard and soffits and fascias are 150mm x 25mm (6" x 1") and pressure treated.

eNTraNCesentrance ways to Carriage Houses are constructed using 150mm x 150mm (6” x 6”) Oak with 610mm (24”) curved bracing. Centre support posts are placed on a 150mm (6") staddle stone.

Doors & WiNDoWsare not included as standard. a wide range of double doors, personal doors and windows are available on request.

HeiGHTMeasures 2505mm (8’ 2”) to eaves when on a single course of brickwork. Carriage Houses are available with an eaves height of 2473mm (9’) as an option. apex heights will vary depending upon the width of the building, please enquire.

GuTTeriNGBlack 100mm (4”) half-round guttering and downpipes are fitted as standard.

TiMBer TreaTMeNTall timber is pressure treated or VaC VaC treated (excluding doors).

TiLeD rooF oPTioNsTo accommodate Clay or slate tiles we increase the pitch of the roof up to a maximum of 35°. Please telephone one of our specialist advisors to discuss the preferred option to suit your requirements and locality.

Ga

ra

Ge

s &

Ca

rr

iaG

e H

ou

se

s

CarriaGe houSe SPeCifiCationS

For any Garage or Carriage House with an eaves height over 2.5m, (not including the height of the roof), full scaffolding will be required.

Please Note: Timber sizes quoted are sawn dimensions and are slightly smaller after planing. We reserve the right to alter our specifications without notice.

Up to 35° Pitch for a tiled roof

Up to 35° Pitch for a tiled roof

Chart Chester Chester

5.4m (18') Wide 3.0m x 5.4m (10' x 18') 1 Bay £2,995 £5,115 £4,150

3.0m (10') Bays 6.1m x 5.4m (20' x 18') 2 Bays £4,925 £7,995 £6,395

9.1m x 5.4m (30' x 18') 3 Bays £6,950 £10,875 £8,645

12.2m x 5.4m (40' x 18') 4 Bays £8,995 £14,295 £10,995

3.6m (12') Bays 3.6m x 5.4m (12' x 18') 1 Bays £3,175 £5,495 £4,395

7.3m x 5.4m (24' x 18') 2 Bays £5,495 £9,325 £7,525

10.9m x 5.4m (36' x 18') 3 Bays £7,450 £13,325 £10,645

14.6m x 5.4m (48' x 18') 4 Bays £9,495 £16,995 £13,745

6.1m (20') Wide 3.0m x 6.1m (10' x 20') 1 Bay £3,450 £5,775 £4,595

3.0m (10') Bays 6.1m x 6.1m (20' x 20') 2 Bays £5,495 £9,445 £7,565

9.1m x 6.1m (30' x 20') 3 Bays £7,795 £13,195 £10,445

12.2m x 6.1m (40' x 20') 4 Bays £9,875 £16,945 £13,545

3.6m (12') Bays 3.6m x 6.1m (12' x 20') 1 Bay £5,495 £9,445 £7,565

7.3m x 6.1m (24' x 20') 2 Bays £7,795 £13,195 £10,445

10.9m x 6.1m (36' x 20') 3 Bays £9,875 £16,945 £13,545

14.6m x 6.1m (48' x 20') 4 Bays £10,595 £18,995 £15,285

7.2m (24') Wide 3.0m x 7.3m (10' x 24') 1 Bay £3,795 £6,375 £5,175

3.0m (10') Bays 6.1m x 7.3m (20' x 24') 2 Bays £6,045 £10,825 £8,650

9.1m x 7.3m (30' x 24') 3 Bays £8,515 £15,145 £12,195

12.2m x 7.3m (40' x 24') 4 Bays £10,825 £19,550 £13,665

3.6m (12') Bays 3.6m x 7.3m (12' x 24') 1 Bay £3,995 £6,845 £5,475

7.3m x 7.3m (24' x 24') 2 Bays £6,375 £11,545 £9,215

10.9m x 7.3m (36' x 24') 3 Bays £9,175 £16,225 £12,975

14.6m x 7.3m (48' x 24') 4 Bays £11,545 £20,785 £16,850


Attach a Workshop 3.0m x 5.4m (10' x 18') £3,245 £4,650 £3,695

3.0m x 6.1m (10' x 20') £3,495 £5,115 £4,095

3.0m x 7.3m (10 x 24') £3,950 £5,750 £4,645

3.6m x 5.4m (12' x 18') £3,395 £5,295 £4,225

3.6m x 6.1m (12' x 20') £3,845 £5,575 £4,495

3.6m x 7.3m (12' x 24') £4,225 £6,050 £4,875


Attach a Garage 3.0m x 5.4m (10' x 18') £3,395 £4,815 £3,845

3.0m x 6.1m (10' x 20') £3,715 £5,245 £4,225

3.0m x 7.3m (10 x 24') £4,095 £5,825 £4,650

3.6m x 5.4m (12' x 18') £3,495 £5,435 £4,345

3.6m x 6.1m (12' x 20') £3,995 £5,715 £4,575

3.6m x 7.3m (12' x 24') £4,335 £6,215 £4,995

The above prices include a 1200mm x 1050mm (47" x 41") opening double glazed casement window and a 838mm wide personal door.

The above prices include a set of 2.2m (7') double doors


Carriage House PriCes

All prices exclude VAT. Prices include installation - Refer to page 3 for delivery charges

Car Port PriCeS

For any Garage or Carriage House with an eaves height of 2.5m and over, (not including the height of the roof) full scaffolding will be required.

5.4m Deep Car PortPressure Treated

Softwood PostsOak

Posts

3.0m x 5.4m (10' x 18') £4,375 £6,245

6.1m x 5.4m (20' x 18') £7,995 £11,195

9.1m x 5.4m (30 x 18') £11,650 £16,145

6.1m Deep Car Port

3.6m x 6.1m (10' x 20') £4,775 £6,795

6.1m x 6.1m (20' x 20') £8,650 £11,945

9.1m x 6.1m (30' x 20') £12,525 £17,115

Car PorTsall sides on our Car Ports are open but have the flexibility to

have one or two sides enclosed, depending on your needs;

location, privacy and prevailing wind direction. once enclosed

on three sides, the building becomes a ‘Carriage House’.

our Car Ports come with either pressure treated softwood posts

or upgrade to our oak posts.

sLaTe or CLaY TiLesour Car Ports are available to take slate or clay tiles, please call to discuss.


Ca

rr

iaG

e H

ou

se

s &

Ca

r P

or

Ts


THe CLiPPer raNGeWaLL CoNsTruCTioNWalls are built with 75mm x 50mm (3” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGSelected high-quality Shiplap 16mm x 150mm (⅝” x 6”), pressure treated to ensure a long maintenance-free life. All boarding is fixed with rust resisting nails. Weatherboard is available as an option.

WaLL LiNiNGa traditional wall eco-breather membrane made to meet the requirements of Bs 4016 Type 2 is placed between the studwork and exterior cladding in all panels and doors. Various wall linings and insulation are available on request.

rooF CoNsTruCTioNPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, covered with 11mm os Board and black onduline roof sheeting or 38kg green mineral felt. Further options include coloured onduline.

Doorsa single 838mm (2’ 9”) wide x 2082mm (6’ 10”) high framed, ledged and braced door faced with shiplap, secured with 450mm (18") T hinges and a pad bolt. Larger single or double doors are available.

WiNDoWsOne 980mm x 660mm (39” x 26”) single glazed pressure treated window (1 x opening, 1 x fixed pane) or 1 x clear roof sheet is included in every 3.6m length of roof as standard. Two pressure treated windows are fitted as standard in our longer Workshops. Alternative an extensive range of single glazed or double glazed windows are available.

HeiGHT2235mm (7’ 4”) to eaves height, when on a single course of brickwork (brickwork is required if the gable end is 3.6m or greater). apex heights will vary depending upon the width of the building, please enquire.


FLooriNGFloors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 400mm (14”) centres and covered with 18mm os Board.


THe CHarT raNGeWaLL CoNsTruCTioNWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

WaLL CLaDDiNGSelected high-quality Shiplap 16mm x 150mm (⅝” x 6”), pressure treated to ensure a long maintenance-free life. All boarding is fixed with rust resisting nails. Weatherboard is available as an option.

WaLL LiNiNGa traditional wall eco-breather membrane made to meet the requirements of Bs 4016 Type 2 is placed between the studwork and exterior cladding of all wall panels and joinery grade doors. Various wall linings and insulation are available on request.

rooF CoNsTruCTioNPurlins are 150mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, boarded with 18mm os Board and covered with Black onduvilla light weight tiles, (shaded brown and red are also available). Further options include 38kg Green mineral felt or felt tiles.

Doorsas standard your Workshop will include a single 838mm x 2082mm (2’ 9” x 6’ 10”) personal door, morticed, ledged and braced framed, faced with Shiplap and fitted with a five levered morticed door lock. This door is hung in a separate door frame; inward or outward opening.

WiNDoWsOne 980mm x 660mm (39” x 26”) single glazed pressure treated window (1 x opening, 1 x fixed pane) or 1 x clear roof sheet is included in buildings up to and including 3.6m (12’) in length. Two windows are fitted as standard in longer workshops. Alternative single glazed or double glazed windows are available.

HeiGHTTo eaves 2235mm (7’ 4”) when on a single course of brickwork (brickwork is required if the gable end is 3.6m or greater). apex heights will vary depending upon the width of the building, please enquire.


BarGe BoarDsAre pressure treated, prepared timber, fixed with rust-resisting nails. 100mm overhangs to each gable end, underlined.

FLoorsFloors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 400mm (14”) centres and covered with 18mm Ply.

TiMBer TreaTMeNTall timber is pressure treated adding to the longevity of your building, (excluding roof purlins and doors).


WorkShoP SPeCifiCationS

For any Garage or Carriage House with an eaves height of over 2.5m, (not including the height of the roof) full scaffolding will be required.

Clipper Chart

2.4m (8') Wide 2.4m x 2.4m (8' x 8') £2,095 £2,445

3.0m x 2.4m (10' x 8') £2,295 £2,745

3.6m x 2.4m (12' x 8') £2,525 £2,850

4.2m x 2.4m (14' x 8') £3,235 £3,715

4.8m x 2.4m (16' x 8') £3,425 £3,950

5.4m x 2.4m (18' x 8') £3,715 £4,345

3.0m (10') Wide 3.0m x 3.0m (10' x 10') £2,445 £2,945

3.6m x 3.0m (12' x 10') £2,695 £3,295

4.2m x 3.0m (14' x 10') £3,395 £3,995

4.8m x 3.0m (16' x 10') £3,595 £4,295

5.4m x 3.0m (18' x 10') £3,945 £4,645

3.6m (12') Wide 3.0m x 3.6m (10' x 12') £2,645 £3,295

3.6m x 3.6m (12' x 12') £2,745 £3,495

4.2m x 3.6m (14' x 12') £3,445 £4,225

4.8m x 3.6m (16' x 12') £3,765 £4,645

5.4m x 3.6m (18' x 12') £3,995 £5,050


Wo

rk

sH

oP

s

WorkShoP PriCeS



DeLiVerY aCross THe uk & euroPeuNiTeD kiNGDoM DeLiVerY & BuiLDiNG iNsTaLLaTioN:in almost all cases we deliver and install our buildings. Where the option for DiY is preferred we have established relations with several reliable hauliers or clients can arrange their own collection. Please contact our support team for further details. You will be supplied you with self-assembly Guidelines drawn up for your building.

DeLiVerY To THe CHaNNeL isLaNDs:Our Equestrian buildings are available on a DIY basis to the Channel Islands. We offer guidance on how to arrange this, having helped many customers from the Channel islands organize this over many years. Please call our support team to discuss this further.

FraNCe & euroPeaN DeLiVerY & iNsTaLLaTioN:We have established experience of delivering our buildings down through France and across europe. We are ideally positioned here in kent, within close proximity to Dover Docks and Calais, to supply our clients across mainland europe. We work closely with two hauliers who travel from kent across europe weekly and can deliver your buildings for self assembly. We can advise on planning applications and VaT exemption, if applicable.our aim is always to ensure the purchase of your Chart Garages is as stress free as possible and that you will go on to enjoy many years of pleasure from our buildings.

DiY CoLLeCTioN:From our Workshops here in ashford, TN23 4FH. You will be supplied with self-assembly Guidelines drawn up for your building.

PreParaTioN & PLaNNiNG serViCePLaNNiNG aND aDViCe serViCe:We can support you with your planning application, providing you with elevated drawings to accompany your planning application. In addition, our support staff can talk you through the design of your equestrian building and give general advice regarding groundworks that may need to be completed prior to assembly.

Do i NeeD PLaNNiNG PerMissioN:Whilst this will not be the answer you will want to hear, in 99% of cases the answer is yes. We would always suggest that a telephone call to your local Council is a good idea. They should give you some good, free advice and in most cases visit you. Listening to their suggestions in the first place may possibly save you time and money. Whilst we cannot give you the advice that a Planning Consultant can, we are able to offer you a helping hand, based on our experience over the years.

HoW LoNG WiLL PLaNNiNG PerMissioN Take:approximately 8 - 10 weeks.

CaN i rePLaCe oLD BuiLDiNGs:Yes, but always make sure you are building like-for-like. Do not exceed the original ground floor area or height. We suggest that you take some photographs of the original buildings. We would advise that you always refer to your local Planning Portal as each local authority does have the right to implement their own rules.

HoW Do i Go aBouT GeTTiNG PLaNNiNG PerMissioN:Firstly, you will need to ask your local Council for the necessary forms if submitting a paper submission alternatively apply on line. These are not as daunting as you may think. The Council will need a scaled site plan, clearly marked with the position of your new buildings and six copies of elevated Drawings. We can supply elevated Drawings to you, if required we can also advise on site Plan preparations. Finally, a cheque or BaCs transfer will need to be sent to the Council along with your chosen application process.

DeLiVerY DaY:on the delivery day it is imperative that our team can get easy and close access to the erecting site. They will work productively and courteously and leave the site tidy.

ProjeCT CoMPLeTioN:on completion, our senior installer will require you to ensure everything has been carried out to your satisfaction and will then require the final payment.

frequently aSkeD queStionS


DiY TiMBer BuiLDiNGsWe offer substantial discounts for DIY buildings collected from our Workshops in Ashford.Buildings are supplied complete. all the components are cut to size, and all the necessary screws, nails and bolts are included in order to make the assembly process as straight forward as possible.self assembly Guidelines and Panel Plans are included and in the unlikely event you encounter a problem, we have experienced staff available to offer advice, over the phone.The tools you will need include a hammer, hand saw, cordless screwdriver and a hammer drill.Please remember we are assembling buildings on a daily basis and it is highly unlikely that you would be able to match this time.

Health and Safety is uppermost in our minds and we would urge you to take great care. The wall panels of our buildings are very heavy, so lifting them can be an issue. Particular care must be taken when on roofs and Scaffold Towers should be used. We would further recommend the use of safety boots and protective eye wear at all times. in the event you need advice we would suggest speaking to your local Health and safety executive, useful information can be found on their website: www.hse.gov.uk

TiMBer TreaTMeNTChart Garages, along with probably 98% of the Country’s leading timber frame building manufacturers have been using a pressure treatment process for twenty years, to Bs & eu standards.

WHaT is TaNaLiseD TiMBer:Tanalised timber has been impregnated with Tanalith e (used to pressure treat timber) , a waterborne product based on copper triazole technology. Copper is derived from recycled sources and triazoles are organic biodegradable biocides, commonly used to protect many of the food crops we eat.This type of timber treatment is used extensively throughout the world and is used in the construction of timber buildings; eg within timber garages, play ground equipment, fencing, timber decking, the list is endless.Pressure treated timber ensures a long maintenance-free life against fungal decay (rot) and insect attack.

WHaT is THe DiFFereNCe BeTWeeN Pressure TreaTiNG, DiPPeD & sPraYeD TiMBer:Buildings that have been manufactured and then dipped or sprayed do not offer the same long term protection. This is a considerably cheaper option with untreated timber costing approximately 15% less than timber that has been pressure treated. This represents a substantial saving to the manufac-turer who doesn't use pressure treated timbers.Perhaps more frustratingly, if your building has not been pressure treated it will require repeated treatments, by yourself, during its life at additional cost and inconvenience to you.

WHY CHoose TaNaLiseD TiMBer:Do you want to spend time and money every year treating your building or do you want the maintenance-free option that opting for Chart’s Tanalised timber offers? Our aim here at Chart Garages is to offer you a building with minimal maintenance during its life except keeping it cobweb free!

FAQ

S


[email protected]

+44 (0)1233 611123

www.chartfencing.co.uk

+44 (0)1233 626188

www.chartgardenbuildings.co.uk

+44 (0)1233 229898

Garden [email protected]

+44 (0)1233 229898

Please Note: Timber sizes quoted are sawn dimensions and are slightly smaller after planing.

We reserve the right to make any changes at any time, without notice, in prices, colours, materials, and specifications, and also to discontinue products. E&OE. 07.2020

Chart Garages, Stables & Garden Rooms, UK & European Sales Office . Chart Fencing Office

Chart House, Dencora Way, ashford, kent TN23 4FH

www.chartgarages.co.uk

Documents

Chart GaraGES Specifications & Prices · Floors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 400mm (14”) centres and covered with 18mm Ply. TiMBer Trea TMeNT