Challenger series mono power tube amplifier - :: · PDF fileChallenger series mono power tube amplifier ... amplifier is similar to the mains voltage normaly supplied to ... This Audio

Challenger series mono power tube amplifier

INSTRUCTIONmanual for

CHALLENGERMONO POWER AMPLIFIER

_____________________________________

This handcrafted product was special made for your high demands,to display the music on ist finest way.

We guarantee,that this amplifier was carefully produced and tested in all details.

_____________________________________________________________________


Congratulations on your decision to become the proud owner of theAUDIO-VALVE Challenger power amplifier.

This manual has been prepared to help you understand the operationof your amplifier and to provide some information about its design and the variety of ways it may be used.

We have designed and manufactured this amplifier to faithfully and accurately reproduce music. This hand build instrument should give a lifetime of pleasure and with a little care and a full understanding of the operation recommendation in this manual the Challenger should provide trouble free performance.

Please take time to read this manualthoroughly before using your amplifier.

List of contents

- Warning and precautions page 3- Front panel - rear panel page 4- Drawing front panel page 4 a- Drawing rear panel page 4 b- Input - output terminals page 5- Polarity - phasing page 5- Installation and operation page 6- Automatic bias control ( ABR ) page 7- Specifications page 8


WARNING

This amplifier Challenger operates in class - A and is therefore capable of generating a moderately high temperatue which requires carefull placing to aviod any effect this heat may have on other equipment, funiture and fittings etc.

Do not remove the top cover from this ampllifier. Hazardous voltages are present. Any repair work should be referered to a suitable qualified and experienced service person.

Do not attemt to connect any input of this amplifier to any of its outputs.

Do not earth any output terminal or connect any of theseterminals together without following the instructions in this manual or seeking qualified assistance.

Do not place this amplifier in any position where liquidsor any foreign material may accidentally enter it.

Do not disconnect any in / output wire, while the amplifier is operating.

Do not connenct any voltage source short circut, earth / ground or appliance (other than suitable HiFi quality loudspeakers ) to any output terminal.

Some preamplifiers, prossesors, CD players etc produce large switching pulses when switched on, causing a loud click through the loudspeakers. For this reason, turn on all other equipment in your system and operate the Stand - by mode of the amplifier before turning on the Challenger.

Note: the Challenger power amplifier do not cause this problem.


FRONTPANEL

The front panel of the Challenger power amplifier incorporates with a small panel filled with two switches. These switches control the day to day function of the amplifier. The operation of this two switches is like following:

MAIN SWITCH

This heavy duty rocker switch is at the right side of this panel and switched the mains / line power of the amplifier On or OFF. A blue LED immediatly beside the switch illuminates to indicate that the power is ON.

This amplifier draws o moderate high current when switched on. It is not good practice to repeatedly active this switch ON and OFF rapidly.

STAND - BY SWITCH.

This switch on the left of the panel alters the operation STAND BY of the amplifier. Switch down is operation STAND BY , ( the LED is off).

REAR PANEL

The facilities on the rear panel of the Challenger may seem not so complex. The rear panel incorporates all of the terminals for connencting the input signals and the output signals to the loadspeaker. A reasonable understanding of this amplifier and the logical approachshould ensure that you are listening to this amplifier in a very short space of time without any difficults at all.

Please remember that the AUDIO VALVE Challenger power amplifier is a high quality electronic instrument capable of an exeptioneal level of performence.

Be sure that you understanding your requirements fully before you make any connection to this amplifier.


INPUT TERMINALSInput terminals for this Challenger power amplifier are easily accsessible and fitted to the lower centre area of the rear panel.RCA INPUT. These standart type of RCA terminals are for use with unbalanced signals from most sigal sources such as audio preamplifiers.XLR BALANCED INPUT. XLR connenctor fitted to the amplifier are for use with balanced line signals from audio preamplifiers etc. Balanced signals are carried via a three way cable that connects all three pins at each of the interconnect cable.

DO NOT operate this amplifier with both RCA and XLR cables connect at the same time.

When using the RCA connector, please place at the XLR input a " Dummy " plug, which has an intern short connection between gnd. and minus phase. OUTPUT TERMINALSOutput connections for the Loudspeakers are provided on the lower centre of the rear panel. Two pairs of heavy duty WBT,gold plated binding postes for each cannel are supplied.CONNECT your loudspeaker positive terminal to the amplifier (+) output terminal. Connect your loudspeaker negative terminal to the ( - ) output terminal.

POLARITY - PHASINGIt is important to achieve good stereo imaging in your listening room. By observing the wiring constructions above, each power amplifier / loudspeaker combination should be in phase. If you experience a poor stereo image and / or a lack of bass, check that the loudspeaker wiring has been connnect correctly. We recommend that you use one of the easily obtainable "test - disc" to help you ensure both phasing and channel orientation are correct. If in doupt, consult your Audio Valve dealer for advice.

Do not make any other connection to any of the amplifiers negative or positive output terminals.

Quality of the connections must be examined to ensure a highperformence trouble free operation is enjoyed.Check that the connections are tight, but do not overtighten with exessive use of spanners etc. If bare wires are used, make sure that no loose strands of wire short across to the other terminals or the ampplifier chassis. When using plugs such as Banana, be sure tu use good quality one`s with a firm fit.


XLR

RCA

Mainplug

Fuse

8 ohm

4 ohm

+

+

-

-

CHALLENGER

123

Feedback

Front-LED

GndGnd

N.C.Plus phase

Neg. Phase

Jumper

Top side from the Challenger PC. Board


INSTALLATION AND OPERATION

MAINS VOLTAGE

CHECK that the mains voltage printed on the rear of this amplifier is similar to the mains voltage normaly supplied to your area. If indoupt, please consult your AUDIO VALVE dealer.

PLACEMENT AND VENTILATION

This Audio Valve Challenger power amplifier is designd to operate at a moderately high temperature. The ideal location is on the rigid stand or floor mounted away from direct contact with any objects, materials or deep pile carpets which may be effected by the heat or which may interrupt the flow of air around the amplifier.When operating the amplifiers quite a lot of heat is generated which should be allowed to dissipate without restriction. Make sure that no objects are placed on the top of the amplifier. Always ensure adequate ventilations.

MAINS / LINE POWER connection is via supplied plug-in lead.The standart IEC socket connects the mains power at the amplifier end while a local mains plug is required at the wall end. In the event where a "local" plug needs to be fitted to the wall end of the lead, ensure the at the plugs is wired correctly by a suitable qualified or experienced person.

Ensure the main switch of the front of this amplifier is OFF before attempting any modification of the mains connection.

MAINS / LINE FUSE

A Mains / Line fuse is fitted within the IEC Mains / Line socket on the rear of the amplifier. A small draw at the bottom of this socket may be removed (after the IEC plug is removed) by levering it out with a flat blade screw driver. The fuse fitted should be razed at no greater than 6.3 ampere slow blow.

In the unusual event that this fuse should blow, you must first esthablish the cause of this failure, cure the fault and then replace the fuse with one of the same type.

DO NOT FIT A FUSE WITH HIGHER RATING.


AUTOMATIC BIAS CONTROL FUNCTION ( ABR )

Each power tube is controlled by an ABR. The correct function of the ABR is shown by three LEDs,next to each power tube.

When the amplifier is operating, no LED is shinning. In case that any of the power tubes is faulty one of the LEDs,which are together at the right side of the power tubes ,immidiatly indicated.

If this happens, you have to change the power tube of this place.After changing the power tube, the LED must be off again.If this does not happen, please check the fuse behind the power tube. A broken fuse is indicated by a shinning LEDunderneath the fuse. Please always and only use a fuse with the rate of 400 mA slow blow.

If still any of the LEDs is on, please contact your Audio-Valve dealer.

Please notice:

All handling at the open amplifier has to be done when the main power plug is disconnected .

In STAND BY MODE, one of the LEDs of the ABR of eachpower tube is shinning.

When the amplifier is driven in a very high level output,the ABRs are regulating the power tubes and there is a slightyshinning of the two LEDs together.


CHALLENGER SPECIFICATIONS:

prinzip: Parallel-push-pull power amp with parallel-symetrical-cross- coupled driver stage

tubes: 2*12AU7, 1*12AX7, 6*beam power pentodefor example: KT 88, EL 34, 6550 …..

operate: class - A

power output: 180 Watt (KT 88, or 6550 with sep. condenser bank)

power consumption: 320 Watt - Stand by mode - 80 Watt

max. short circuit current: 70 ampere between 2 ohm terminals

input sen. 0 dBm

input imp. 2 * 47K

output imp: 2-4-6-8 ohm

connectors: XLR & RCA input-jacket

power bandwide: 5-40.000 hz

distortion: 0,3% - 50 Watt (8 ohm load)

damping: 5

bias: autom. contolled with "ABR" for all power tubes

size: 43*28*24 cm, D-H-W

weight: 48 pounds

Stand-by mode: switchable


Certificate of Compliance Restriction of the use of Hazardous Substances (RoHS)

We certify that all of our products (exceptions see listed below) are compliant with the European UnionDirective 2002/95/EC for the Restriction of the use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS). No Lead (Pb), Cadmium (Cd), Mercury (Hg), Hexavalent Chromium (Cr+6), PBB or PBDE is intentionally added to these devices. Any trace impurities of these substances contained in the parts are below the RoHS specified threshold levels.All information provided in this Certificate of Compliance is accurate to the best of our knowledge as ofthe date this Certification was issued.

Certificate of Compliance

Registration, Evaluation, Authorization and Restriction of chemicals (REACh)

We declare that all of our products European Union Directive EC1907/206 for the Registration, Evaluation, Authorization and Restriction of chemicals (REACh), and contain none or less than 0.1% of the chemicals listed as hazardous chemicals in the REACh regulation. All information provided in this Certificate of Compliance is accurate to the best of our knowledge as of the date this Certification was issued.

Declaration of Conformity EMC and Low Voltage Directive (CE)

Product Name: AudioValve Model name: RKV MARK 3

This is to certify that the product listed above complies with the following European Union Council Directives and Standards relating to electromagnetic compatibility (EMC Directive 89/336/EEC) and the low voltage Directive (73/23/EEC).

This declaration of conformity of the European Communities is the result of an examination carried out byElectromagnetic Engineering Services, Inc. in accordance with European Standards EN 50081-1, EN 50082-1 and EN 60065 for low voltage, as laid down in Article 10 of the EMC Directive.

Helmut Becker, AudioValveUmbachsweg 7034 123 KASSEL - Germany


W A R R A N T Y

AUDIOVALVE warrants its components for a three-year period on all electronics and a 90 - day period on the tubes from the purchase date.

In the event of a failure of your amplifier, AUDIOVALVE will repair or readjust this unit or, should the occasion arise, will replace it provided that all conditions stipulated in this warranty are met.

In order to initiate service of any kind it is necessary to obtain distributor or dealer authorization prior to shipping the unit for service.

Any of the following conditions shall void the warranty:

Operation not in accordance with this manual.

Abuse , accidental damage or unauthorized modifications , as determined by AUDIOVALVE or its agents exclusively.

Removal, defacing or falsifying of the serial numbers.

Shipping without the original complete factory crates.

W A RR A N T Y R E GI ST R A T I O N

Please fill out and return this warranty form to the distributor within 15 days of the purchase date, or fill out our online warranty registration form at: w w w. a u d o v a lv e . i n f o

MODEL :

SERIAL NUMBER :

PURCHASE DATE :

AUTHORIZED AUDIO - VALVE DEALER:

PURCHASER`S NAME :

STREET ADDRESS :

CITY :

ZIP / POSTAL CODE :

http://www.audovalve.info/

















WARRANTY REGISTRATION

Please fill out and return this warranty form to the distributor within 15 days of the purchase date with this form here, or make it online on our webside.

• MODEL : _______________________________________________

• SERIAL NUMBER : _______________________________________

• PURCHASE DATE : ______________________________________

• AUTHORIZED AUDIOVALVE DEALER:

• PURCHASER`S NAME : ___________________________________

• STREET ADDRESS : ______________________________________

• CITY : __________________________________________________

ZIP / POSTAL CODE : _____________________________________

0561 - 701 33 600160 910 77 376

0561 – 60 2929 [email protected]

Fa. Helmut Becker ProduktionMarken: AUDIOVALVE & BE-TECUmbachsweg 7034 123 KASSEL - Germany

U-St.Ident.Nr.: 195 191 420WEEE-Reg.Nr.: DE81178274 Gerichtsstand: Kassel

12AX7 61896189

Fuse-LED

Bias LED

Fuse

0.63 s.b.

Documents

Challenger series mono power tube amplifier - :: · PDF fileChallenger series mono power tube amplifier ... amplifier is similar to the mains voltage normaly supplied to ... This Audio