Certificate of Compliance - Bel - Power · CERTIFICATE No. P15220260 Order No. 293466 Page 1/3 Date of issue 25-09-2015 Juan Z. Kleppenes Certification Department Nemko AS Gaustadalléen

DQD 507 Rev. 2012-05-22 Page 1

Certificate of Compliance Certificate: 70036130 (170351) Master Contract: 170351

Project: 70044582 Date Issued: 2015-09-02

Issued to: Bel Fuse Inc. 206 Van Vorst St Jersey City, New Jersey 07302 USA

Attention: Editha S. Vergara

The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent

indicator 'US' for US only or without either indicator for Canada only.

Issued by: Maggie Lam Maggie Lam

PRODUCTS CLASS - 531111 - POWER SUPPLIES-Component Type (CSA 60950-1-07-2nd Ed) CLASS - 531191 - POWER SUPPLIES-Component Type (UL 60950-1-2nd Ed) Certified to U.S.Stds Component type power supplies intended for use with Information Technology and Business Equipment, where the suitability of the combination is to be determined by CSA Group. AC/DC Switching Power Supply, Models PFE3000-12-069RA and SPAFFIV-05G, model designation may be followed by suffix SXXX denoting non-safety critical option. Electrical Ratings: Model PFE3000-12-069RA Input rated 100-277Vac/240-380 Vdc, 17-12.5A AC/13-9 A DC, 50-60 Hz; Outputs rated (V1)* 12.3V dc, 244A, (V2) 12V dc, 5A, Total maximum output power shall not exceed 3060 W, 45 °C ambient. *Note: V1 output is derated as per the below conditions:

1400 W at 100-200 Vac, 45 °C ambient 2250 W at 200-277 Vac/240-380 Vdc, 55 °C ambient 1050 W at 100-200 Vac, 55 °C ambient

Certificate: 70036130

Project: 70044582

Master Contract: 170351

Date Issued: 2015-09-02

DQD 507 Rev. 2012-05-22 Page 2

Model SPAFFIV-05G Input rated 200-277Vac/240-380 Vdc, 17-12.5A AC/13-9 A DC, 50-60 Hz; Outputs rated (V1)* 12.25V dc, 244A, (V2) 12V dc, 5A, Total maximum output power shall not exceed 3000 W, 45 °C ambient. *Note: V1 output is derated as per the below condition:

2250 W at 200-277 Vac/240-380 Vdc, 55 °C ambient APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No 60950-1-07, +Am.1:2011 +Am.2:2014

Information Technology Equipment - Safety - Part 1: General Requirements

UL 60950-1-2014 Information Technology Equipment - Safety - Part 1: General Requirements

CONDITIONS OF ACCEPTABILITY 1. This component has been judged on the basis of the required spacings in the Standard for Safety of

Information Technology Equipment, CSA/UL 60950-1, Second Edition +Am. 1 +Am. 2, Sub-clause 2.10, which would cover the component itself if submitted for Listing.

2. The equipment has been evaluated for use in Pollution Degree 2 environment. 3. The Clearance values of the Power Supply Unit (PSU) have been evaluated for an altitude of 4000 m,

under IEC60664-1: 1992 Table A.2 (altitude correction factor is 1.29). 4. The ground path from the input connector to the PSU case meets protective bonding and has been

evaluated at 80 A. 5. The PSU has been evaluated for use in Class I equipment. 6. The secondary outputs of the PSU are SELV. 7. V2 output is non-hazardous energy level. V1 output is at hazardous energy level. 8. The PSU has been evaluated for a TN (Including TN-S and TN-C) and TT systems power source. 9. The PSU has been evaluated for use with a Phase – Neutral power source. 10. All Isolating transformers isolation barrier insulation temperatures have been measured within the

winding on the insulator. The internal temperature did not exceed the insulation Class limits for NORMAL operation and ABNORMAL operation.

11. The temperature of the Isolating Transformers, T4, T3/T9/T14/T15, T6/T7/T8/T11 isolation barrier shall be assessed in the end application. T4, T3/T9/T14/T15 employ an OBJY3 electrical insulation system designated Class F. Transformers, T6/T7/T8/T11, employs a Class B insulation system.

12. The connector current interruption test (Hot Plugging test) was conducted on the secondary connector of the PSU for 100 cycles.

13. The PSU is not intended for use in vehicles, on board ships or aircraft. 14. The front face of the PSU may be a part of the front of the end product. The front face of the PSU did

pass the ‘Impact Test’.

DQD 507 Rev. 2012-05-22 Page 1

Supplement to Certificate of Compliance

Certificate: 70036130 (170351) Master Contract: 170351

The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate.

Product Certification History

Project Date Description

70044582 2015-09-02 Update Report 70036130 to change the EMI capacitors (C7, C16, C17) values

70036130 2015-06-26 AC/DC Switching Power Supply, Models PFE3000-12-069RA and SPAFFIV-05G. (C/US) (transferred from 173688 - 2650530 and upgraded to include Am2).

CERTIFICATENo. P15220260

Order No. 293466 Page 1/3

Date of issue 25-09-2015

Juan Z. KleppenesCertification Department

Nemko ASGaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, NorwayTEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL [email protected] NUMBER NO974404532 nemko.com

Product AC/DC or DC/DC Switching Power

Applicant Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Manufacturer Bel Fuse Inc.206 Van Vorst St.Jersey City, NJ 07302USA

Factory BPS Asia Pacific Electronics (Shenzhen) Co., Ltd.Building# 6, Nanming Road, Gongming Town HuahongXintong Industrial ParkGuangming District, Shenzhen 518108China

See next page(s)

Ratings Input: 100-277 Vac, 17-12.5A, 50-60Hz or 240-380 Vdc, 13-9A

Trade mark

Model / Type Ref. PFE3000-12-069RA, PFE3000-S361

Principal characteristics DC Output(s): V1*: 12.3V, 244A: V2: 12V, 5A. Total Maximum Power: 3060W, 45ºC ambient. The model name may be followed by SXXX indicating non-safety critical option

See next page(s)

A sample of the product was testedand found to be in conformity with

OFF EN 60950-1:2006;A11;A1;A12;A2

Validity This certificate documents conformity with the standards shown, and also applies as license foruse of Nemkos name and certification mark. The certificate and license is valid as long as theapplicable conditions are complied with, and provided that any changes to the product are notifiedto Nemko for acceptance prior to implementation.New standards or amendments to the standards may imply that the product design must beupdated and/or that re-testing and re-certification is necessary.

Additional information See next page(s)

The abovementioned certified equipment complies with current regulatory requirements regardingelectrical safety in Norway and other EU/EEA member states, as far as this can be checked.Compliance with requirements regarding building-in, protection against electric shock and






Electromagnetic Compatibility (EMC) must be checked when the equipment is built-in a completedproduct or forms a part of a complete system.

Additional model(s) See next page(s)






Product AC/DC or DC/DC Switching Power

Pos. No 1Model / Type Ref. SPAFFIV-05GTrade mark (if different from page 1) Rating Input: 200-277 Vac, 17-12.5A, 50-60Hz or 240-380 Vdc, 13-9APrincipal characteristics DC Output(s): V1: 12.25V, 244A; V2: 12V, 5A Total Maximum Power:

3000W 45ºC ambient. The model name may be followed by SXXX indicatingnon-safety critical option

Ref. Certif. No.

NO88555

Gaustadalléen 30

NO-0373 Oslo, Norway

Date: 25-09-2015 Signature: Juan Z. Kleppenes

Certification Department

Issued 2007-04 1/1

IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL

EQUIPMENT (IECEE) CB SCHEME

SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DES

EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC

CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC

Product

ProduitAC/DC or DC/DC Switching Power Supply

Name and address of the applicant

Nom et adresse du demandeur

Name and address of the manufacturer

Nom et adresse du fabricant

Name and address of the factory

Nom et adresse de l'usine

Note: When more than one factory, please report on page 2

Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page Additional information on page 2

Ratings and principal characteristics

Valeurs nominales et caractéristiques principalesInput: 200-277 Vac, 17-12.5A, 50-60Hz or 240-380 Vdc, 13-9A

Trademark (if any)

Marque de fabrique (si elle existe)

Type of Manufacturer’s Testing Laboratories used

Type de programme du laboratoire d’essais constructeur

Model / Type Ref.

Ref. De typeSPAFFIV-05G

Additional information (if necessary may also be

reported on page 2)

Les informations complémentaires (si nécessaire,

peuvent être indiqués sur la deuxième page

DC Output(s): V1: 12.25V, 244A; V2: 12V, 5A Total Maximum Power:

3000W 45ºC ambient. The model name may be followed by SXXX

indicating non-safety critical option Additional information on page 2

A sample of the product was tested and found

to be in conformity with

Un échantillon de ce produit a été essayé et a été

considéré conforme à la

IEC 60950-1(ed.2);am1;am2

As shown in the Test Report Ref. No. which forms part

of this Certificate

Comme indiqué dans le Rapport dessais numéro de

référence qui constitue partie de ce Certificat

293466

This CB Test Certificate is issued by the National Certification Body

Ce Certificat dessai OC est établi par l'Organisme National de Certification

Ref. Certif. No.

NO88556

Gaustadalléen 30




Issued 2007-04 1/1






Product












Trademark (if any)




Model / Type Ref.

Ref. De typePFE3000-12-069RA, PFE3000-S361


reported on page 2)



DC Output(s): V1*: 12.3V, 244A: V2: 12V, 5A. Total Maximum Power: 3060

W, 45ºC ambient. The model name may be followed by SXXX indicating

non-safety critical option Additional information on page 2





IEC 60950-1(ed.2);am1;am2


of this Certificate



293466



Ref. Certif. No.

NO88556

Gaustadalléen 30




Issued 2007-04 1/1






Product












Trademark (if any)




Model / Type Ref.

Ref. De typePFE3000-12-069RA, PFE3000-S361


reported on page 2)



DC Output(s): V1*: 12.3V, 244A: V2: 12V, 5A. Total Maximum Power: 3060

W, 45ºC ambient. The model name may be followed by SXXX indicating

non-safety critical option Additional information on page 2





IEC 60950-1(ed.2);am1;am2


of this Certificate



293466



Test Report issued under the responsibility of

www.nemko.com

TEST REPORT

IEC 60950-1 Information technology equipment – Safety –

Part 1: General requirements

Report Number. ............................. : 293466

Date of issue ................................... : 22 September 2015

Total number of pages ..................... 62

Applicant’s name ........................... : Bel Fuse Inc.

Address ........................................... : 206 Van Vorst St., Jersey City, NJ 07302

Test specification:

Standard .......................................... : IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013

Test procedure ................................ : CB-Scheme

Non-standard test method ............... : N/A

Test Report Form No. .................... : IEC60950_1F

Test Report Form(s) Originator ....... : SGS Fimko Ltd

Master TRF ..................................... : Dated 2014-02

Copyright © 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

General disclaimer:

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report.

Page 2 of 62 Report No 293466

TRF No. IEC60950_1F

Test item description .................... : AC/DC or DC/DC Switching Power Supply

Trade Mark ...................................... :

Manufacturer ................................... : Same as Applicant

Model/Type reference...................... : PFE3000-12-069RA, PFE3000-S361 and SPAFFIV-05G (maybe followed by SXXX indicating non-safety critical option)

Ratings ............................................ : Model PFE3000-12-069RA and PFE3000-S361

Input: 100-277 Vac, 17-12.5 A, 50-60 Hz or 240-380 Vdc, 13-9 A

Output(s), DC: V1*: 12.3 V, 244 A ; V2: 12 V, 5 A

Total Maximum Power: 3060 W, 45 °C ambient

*Note: V1 output is derated as per the below conditions: 1400 W at 100-200 Vac, 45 °C ambient 1050 W at 100-200 Vac, 55 °C ambient

2250 W at 200-277 Vac / 240-380 Vdc, 55 °C ambient

Model SPAFFIV-05G:

Input: 200-277 Vac, 17-12.5 A, 50-60 Hz or 240-380 Vdc, 13-9 A

Output(s), DC: V1*: 12.25 V, 244 A ; V2: 12 V, 5 A

Total Maximum Power: 3000 W, 45 °C ambient

*Note: V1 output is derated as per the below condition:

2250 W at 200-277 Vac / 240-380 Vdc, 55 °C ambient

Testing procedure and testing location:

CB Testing Laboratory: Nemko USA Inc.

Testing location/ address ............................: 2210 Faraday Ave. Suite 150, Carlsbad, CA 92008, USA

Testing procedure:CTF-3 BPS Pacific Electronics (Shenzhen) Co.,Ltd.

Testing location/ address ........................... : Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA

Tested by (name + signature) ..................... : George Daverin

Approved by (name + signature) ................ : Jeff Busch


TRF No. IEC60950_1F

Report History:

Modification1: Report 277712 has been modified due to change of Y2-capcitors C7(main board) and C16/C17 (Input board) ratings and addition of model PFE3000-S361.

List of Attachments (including a total number of pages in each attachment):

Attachment 1: European Group Differences and National Deviations .......................................... 83 pages

Documented deviations contain individual national documents for several European countries that are already documented in the European Group Deviations. The European Group Differences: EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013 are considered “Normative”. The individual national documents (Denmark, Finland, Germany, Ireland, Norway, Spain, Sweden, Switzerland and United Kingdom) are considered “Informative” and included at the manufacturer’s request.

Attachment 2: Miscellaneous Documentation, e.g. Photos, etc. .................................................. 34 pages (Not for publication – Engineering use only)


TRF No. IEC60950_1F

Summary of testing

General All comments relate to all models, unless specifically stated.

Power supply The equipment is an enclosed, Class I switch mode power supply with universal AC input or Class I with DC input. With multiple DC voltage outputs for building-in. This report covers multiple models and all comments / tests apply to all models unless otherwise indicated. Testing was conducted on various models as indicated.

1.1.2; The unit is intended to operate at an altitude of up to 4000m.

This equipment is intended to be operated at an altitude of up to 4000 m, so the clearance is multiplied by the altitude correction factor (1.29), specified in table A.2 of IEC 60664-1 2nd Edition:2007-04. Refer to Tables 2.10.3 and 2.10.4.

1.5, 3.2.5; Power supply cord set. A power supply cord set is not provided with the power supply. A power supply cord set, complying with the national regulations of the country in which the product is to be sold, shall be provided with the end-use equipment.

1.7.2; Safety instructions. Instructions and equipment markings related to safety are to be provided in a language, which is acceptable in the country in which the equipment is to be sold. English language verified.

1.7.2.4; IT power distribution systems The equipment complies with the requirements for connection to the Norwegian IT power systems. The following information should be given (but is not required) in the installation instruction: “This product is also designed for IT power system with Phase to Phase voltage 230V.”

2.7.4; Number and location of protective devices. In Norway, IT power distribution system is used. Equipment with a single protective device is accepted in Norway. Other countries may have additional requirements. Equipment normal configuration is provided with a single fuse (F1) in the line phase of the input, however the power may be supplied with an optional fuse (F2) in the neutral phase of the input.

2.7.6; Warning to service personnel. After operation of the protective device, the equipment is still under voltage if it is connected to an IT-power system. A warning is required for service personnel. Norway does not require this warning.

5.2: Electric Strength test Increased test voltages for Basic insulation applied to the equipment, based on measured working voltages.


TRF No. IEC60950_1F

Summary of testing:

Tests performed (name of test and test clause):

1) Input Test .................................................... 1.6.2

2) Durability Test ........................................... 1.7.11

3) Energy Hazard ......................................... 2.1.1.5

4) Capacitance Discharge Test .................... 2.1.1.7

5) SELV Reliability Test ..................................... 2.2

6) Protective Bonding Test ........................... 2.6.3.4

7) Humidity Test .............................................. 2.9.2

8) Working Voltage Measurement ................. 2.10.2

9) Hazardous Voltage Measurement ............ 2.10.2

10) Cemented Joint ................................... 2.10.5.5

10) Impact test ................................................ 4.2.5

11) Handel Loading test………………………….4.3.2

12) Connector Interruption test ....................... 4.3.5

13) Heating Test ............................................. 4.5.1

14) Touch Current Test ...................................... 5.1

15) Electric Strength Test ............................... 5.2.2

16) Component Failure Test .............................. 5.3

17) Abnormal Operation Test ............................. 5.3

18) PS Output Overload and Short Test ............ 5.3

Testing location:

BPS Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA


TRF No. IEC60950_1F

Summary of compliance with National Differences:

List of countries addressed

Austria (AT), Australia (AU), Canada (CA), China (CH), Denmark (DK), Finland (FI), Germany (DE), Ireland (IE), Israel (IS), Korea (KR), Norway (NO), Slovenia (SI), Spain (ES), Sweden (SE), Switzerland (CH), United Kingdom (GB), United States of America (US)

The product fulfils the requirements of : EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013


TRF No. IEC60950_1F

Copy of marking plate: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective Certification Bodies that own these marks.


TRF No. IEC60950_1F

Calibration All instruments used in the tests given in this test report are calibrated and traceable to national or international standards. Further information about traceability will be given on request.

Measurement uncertainty

Measurement uncertainties are calculated for all instruments and instrument set-ups given in this report. Calculations are based on the principles given in the standard EA-4/02 (Dec. 1999), IEC Guide 115:2007, Nemko routine L227 and other relevant internal Nemko-procedures. Further information about measurement uncertainties will be given on request.

Evaluation of results If not explicitly stated otherwise in the standard, the test is passed if the measured value is equal to or below (above) the limit line, regardless of the measurement uncertainty. If the measured value is above (below) the limit line, the test is not passed - ref IEC Guide 115:2007, and Nemko routine L220. The instrumentation accuracy is within limits agreed by IECEE-CTL (ref. Nemko routine L227).


TRF No. IEC60950_1F

Test item particulars:

Equipment mobility ...................................................... : [] movable [] hand-held [] transportable [] stationary [ X ] for building-in [] direct plug-in

Connection to the mains ............................................. : [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [X] not directly connected to the mains [ X ] DC Mains

Operating condition ..................................................... : [ X ] continuous [] rated operating / resting time:

Access location .......................................................... : [] operator accessible [] restricted access location [X] Equipment for building –in, to be evaluated in end use equipment.

Over voltage category (OVC) .................................... : [] OVC I [ X ] OVC II [] OVC III [] OVC IV [] other:

Mains supply tolerance (%) or absolute mains supply values ......................................................................... :

90 to 300 Vac for PFE3000 Series 180 to 300 Vac for SPAFFIV-05G 192 to 400 Vdc (both models)

Tested for IT power systems ..................................... : [X] Yes (Norway only) [ ] No

IT testing, phase-phase voltage (V) .......................... : 230V

Class of equipment .................................................... : [X] Class I (For AC input) [ ] Class II [X] Class III (For DC input) [] Not classified

Considered current rating of protective device as part of the building installation (A) .................................... :

40 A (per manufactures specification)

Pollution degree (PD) ................................................. : [] PD 1 [ X ] PD 2 [] PD 3

IP protection class ...................................................... : IP20

Altitude during operation (m) ..................................... : 4000 m

Altitude of test laboratory (m) .................................... : 100 m

Mass of equipment (kg) ............................................. : 2.53 kg PFE3000 Series

2.78 kg SPAFFIV-05G

Possible test case verdicts:

- test case does not apply to the test object ................ : N/A

- test object does meet the requirement ...................... : P (Pass)

- test object does not meet the requirement ................ : F (Fail)

Testing ........................................................................ :

Date of receipt of test item ........................................... : March,2015: Septermber,2015

Date (s) of performance of tests .................................. : March,2015: Septermber,2015


TRF No. IEC60950_1F

General remarks:

"(See Enclosure #)" refers to additional information appended to the report.

"(See appended table)" refers to a table appended to the report.

Throughout this report a comma / point is used as the decimal separator.

Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:

The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided .... :

Yes

Not applicable

When differences exist; they shall be identified in the General product information section.

Name and address of factory (ies) :

BPS Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District 518108 Shenzhen PEOPLE'S REPUBLIC OF CHINA

General product information:

This test report is based on Nemko test report Ref. No. 277712 with appended CB cert Ref. No.NO85140, evaluated to the requirement of IEC60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013. This test report includes the addition of a model name. PFE3000-S361 is exactly the same as PFE3000-12-069RA except for Multiple square holes on the side of the enclosure. Therefore only temperature data, table 4.5, was included to document this addition. Additionally the values of the Y2 capacitors and some of the bulk capacitors were changed, Table 5.1 was updated to document this change. Additionally, table 1.5.1 was added to this report. For continuity, the entire report has been reissued, including the additional evaluation highlighted in bold text.

The subject models are component type power supplies, intended for building in, provided with an overall metal enclosure, housing components operating at hazardous and SELV voltages. Multiple hexagonal holes are provided on the front and square holes on the rear of the enclosure.

Supplies can operate from AC input or DC Input, with DC outputs

The following PWB assemblies are provided: Main PWB is installed on multiple stand-offs secured to the chassis bottom by machine screws; Control PWB is mounted vertically along the side of the main PWB, and connected to the Main PWB through multi-pin connectors. Insulating foil is provided between PWB assemblies and enclosure panels.

The units are equipped with an input connector for power connection, fan and LED.

The models covered in this report do not connect directly to Mains. They are provided with connectors that interface with the host system. Class B or permanent connection to Mains must be determined in the end use equipment.

Model Differences:

SPAFFIV-05G is exactly the same as PFE3000-12-069RA except for AC input voltage rating, V1 output voltage rating, wider chassis (refer to appended table 1.5.1) and different location of bonding conductor.

PFE3000-S361 is exactly the same as PFE3000-12-069RA except for Multiple square holes on the side of the enclosure


TRF No. IEC60950_1F

Conditions of Acceptability:

The following must be evaluated at end use:

1. The equipment has been evaluated for use in Pollution Degree 2 environment. 2. The Clearance values of the Power Supply Unit (PSU) have been evaluated for an altitude of 4000 m,

under IEC 60664-1:1992 Table A.2 (altitude correction factor is 1.29). 3. The ground path from the input connector to the PSU case meets protective bonding and has been

evaluated at 80 A. 4. The PSU has been evaluated for use in Class I equipment.

5. The secondary outputs of the PSU are SELV. 6. V2 output is non-hazardous energy level. V1 output is at hazardous energy level.

7. The PSU has been evaluated for a TN (Including TN-S and TN-C) and TT and IT (Norway only) systems power source.

8. The PSU has been evaluated for use with a Phase – Neutral power source.

9. All Isolating transformers isolation barrier insulation temperatures have been measured within the winding on the insulator. The internal temperature did not exceed the insulation Class limits for NORMAL operation and ABNORMAL operation.

10. The temperature of the Isolating Transformers, T4, T3/T9/T14/T15, T6/T7/T8/T11 isolation barrier shall be assessed in the end application. T4, T3/T9/T14/T15 employ an OBJY3 electrical insulation system designated Class F. Transformers, T6/T7/T8/T11, employs a Class B insulation system.

11. The connector current interruption test (Hot Plugging test) was conducted on the secondary connector of the PSU for 100 cycles.

12. The PSU is not intended for use in vehicles, on board ships or aircraft.

13. The front face of the PSU may be a part of the front of the end product. The front face of the PSU did pass the ‘Impact Test’.

14. Equipment is rated higher than 16A. Type of connection to Mains must be determine in the end use equipment.

15. The suitability of fusing included in the PSU construction, must be evaluated in the end use equipment.

Abbreviations used in the report:

- normal conditions ...................................... N.C. - single fault conditions ........................ S.F.C - functional insulation ..................................... OP - basic insulation ....................................... BI - double insulation ........................................... DI - supplementary insulation ........................ SI - between parts of opposite polarity ............. BOP - reinforced insulation ................................ RI

Indicate used abbreviations (if any): .......... None

Documents

Certificate of Compliance - Bel - Power · CERTIFICATE No. P15220260 Order No. 293466 Page 1/3 Date of issue 25-09-2015 Juan Z. Kleppenes Certification Department Nemko AS Gaustadalléen