Current issue date: 21 May 2020 Original approval(s):Expiry date: 24 May 2021 ISO 9001 - 25 May 2006 Certificate identity number: 10268915

Certificate of Approval

David Derrick

Area Operations Manager UK & Ireland

Issued by: Lloyd's Register Quality Assurance Limited

Lloyd's Register Group Limited, its affiliates and subsidiaries, including Lloyd's Register Quality Assurance Limited (LRQA), and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract.Issued by: Lloyd's Register Quality Assurance Limited, 1 Trinity Park, Bickenhill Lane, Birmingham B37 7ES, United Kingdom

Page 1 of 2

This is to certify that the Management System of:

ARRK Europe LimitedLondon Gateway Logistics Centre, North One, North Sea Crossing, Stanford-le-Hope, SS17 9ER,United Kingdom

has been approved by Lloyd's Register to the following standards:

ISO 9001:2015Approval number(s): ISO 9001 – 0005219

This certificate is valid only in association with the certificate schedule bearing the same number on which the locations applicable to this approval are listed.

The scope of this approval is applicable to:

Design, procurement and predictive analysis of vehicles and components, prototype build and assembly. Management of the customer and supplier relationships.

Certificate identity number: 10268915

Certificate Schedule

Lloyd's Register Group Limited, its affiliates and subsidiaries, including Lloyd's Register Quality Assurance Limited (LRQA), and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract.Issued by: Lloyd's Register Quality Assurance Limited, 1 Trinity Park, Bickenhill Lane, Birmingham B37 7ES, United Kingdom

Page 2 of 2

Location Activities

London Gateway Logistics Centre, North One, North Sea Crossing, Stanford-le-Hope, SS17 9ER,United Kingdom

ISO 9001:2015Design, procurement and predictive analysis of vehicles and components, prototype build and assembly. Management of the customer and supplier relationships.

Units 27-30, Laurence Industrial Estate, Eastwoodbury Lane, Southend-on-Sea, SS2 6RH, United Kingdom

ISO 9001:2015Design, procurement and predictive analysis of vehicles and components, prototype build and assembly. Management of the customer and supplier relationships.

The use of the UKAS Accreditation Mark indicates accreditation in respect of those activities covered by the accreditation certificate number 015 held by NQA. NQA is a trading name of NQA Certification Limited, Registration No. 09351758. Registered Office: Warwick House, Houghton Hall Park, Houghton Regis, Dunstable Bedfordshire LU5 5ZX, United Kingdom. This certificate is the property of NQA and must be returned on request.

Page 1 of 1

This is to certify that the Quality Management System of:

Arrk Europe Limited (Nuneaton Technical Centre)

Caldwell Road, Nuneaton, Warwickshire, CV11 4NG, United Kingdom

applicable to:

The manufacture of composite panels, assemblies and metals for the aerospace

markets

has been assessed and registered by NQA against the provisions of:

ISO 9001:2015

This registration is subject to the company maintaining a quality management system, to the

above standard, which will be monitored by NQA

FManaging Director

Certificate No. 124967

11 November 2014ISO Approval Date:

Reissued: 29 November 2019

Valid Until: 10 November 2020

EAC Code: 14, 17

The use of the UKAS Accreditation Mark indicates accreditation in respect of those activities covered by the accreditation certificate number 015 held by NQA. NQA is a trading name of NQA Certification Limited, Registration No. 09351758. Registered Office: Warwick House, Houghton Hall Park, Houghton Regis, Dunstable Bedfordshire LU5 5ZX, United Kingdom. This certificate is the property of NQA and must be returned on request.

Page 1 of 1

This is to certify that the Quality Management System of:

Arrk Europe Ltd

Gloucester Technical Centre, Olympus Park, Quedgeley, Gloucester, GL2 4NF, United

Kingdom

applicable to:

Project management and manufacture of prototype of parts and services including

non-export tooling

has been assessed and registered by NQA against the provisions of:

ISO 9001:2015

This registration is subject to the company maintaining a quality management system, to the

above standard, which will be monitored by NQA

FManaging Director

Certificate No. 25068/1

30 April 2015ISO Approval Date:

Reissued: 14 April 2020

Valid Until: 2 May 2023

EAC Code: 23

The use of the UKAS Accreditation Mark indicates accreditation in respect of those activities covered by the accreditation certificate number 015 held by NQA. NQA is a trading name of NQA Certification Limited, Registration No. 09351758. Registered Office: Warwick House, Houghton Hall Park, Houghton Regis, Dunstable Bedfordshire LU5 5ZX, United Kingdom. This certificate is the property of NQA and must be returned on request.

Page 1 of 1

This is to certify that the Environmental Management System of:

Arrk Europe Ltd

Gloucester Technical Centre, Olympus Park, Quedgeley, Gloucester, GL2 4NF, United

Kingdom

applicable to:

Project management and manufacture of prototype of parts and services including

non-export tooling

has been assessed and registered by NQA against the provisions of:

ISO 14001:2015

This registration is subject to the company maintaining an environmental management

system, to the above standard, which will be monitored by NQA

FManaging Director

Certificate No. E8781/2

23 April 2015ISO Approval Date:

Reissued: 14 April 2020

Valid Until: 2 May 2023

EAC Code: 23