CERN SX5 JUNE AND JULY 2006jnb/cms/docs/YE+1_photogrammetry_V...CMS – SX5 – YE+1 Photogrammetry YE+1 June and July 2006 CMS-SG-UR-0058 Version 2 2561_YEP1ZM_PG_V2.doc Page 3

CMS – SX5 – YE+1 Photogrammetry YE+1

June and July 2006CMS-SG-UR-0058 Version 2

2561_YEP1ZM_PG_V2.doc Page 1 / 33 J.F. FUCHS – R. GOUDARD – JD MAILLEFAUD

GENEVE, SUISSE Date: 19 November 2007 From: J.F. FUCHS PH/CMI

R. GOUDARD PH/CMI J.D. MAILLEFAUD PH/CMI

CMS-SG-UR-0058 EDMS: 768246

VERSION 2

CCMMSS –– YYEE++11

PPHHOOTTOOGGRRAAMMMMEETTRRYY OOFF TTHHEE YYEE++11 FFAACCEE ZZ-- ,, MMEE++11 LLAAYYEERR

CERN – SX5 – JUNE AND JULY 2006

To: A. BALL PH/CMO G. BENCZE PH/CMM E. CALVO PH/UCM J. BOS PH/CMM D. CAMPI PH/CMI D. EARTLY FNAL G. FABER PH/UCM W. FUNK PH/CMA A. GADDI PH/CMI H. GERWIG PH/CMI S. GURAGAIN PH/UCM J. P. GIROD PH/CMI A. HERVE PH/CMI M. HOHLMANN PH/UCM

A. LANARO PH/UFT P. INGENITO PH/CMM C. LASSEUR TS/SU P. LEVCHENKO PH/UCM D. LOVELESS PH/UCM T. RODRIGO TS/UCM A. SHARMA PH/CMM Z. SZILLAZI PH/CMM L. VEILLET PH/CMI D. WENMAN PH/UCM W. ZEUNER PH/CMM




TABLE OF CONTENTS

1 INTRODUCTION.............................................................................................3

1.1 Needs ......................................................................................................................................... 3

1.2 Measurements .......................................................................................................................... 3

2 COORDINATES SYSTEM..............................................................................4

2.1 Coordinate system.................................................................................................................... 4

2.2 Calculation of 3D coordinates ................................................................................................. 4

3 POINT NUMBERING AND ADAPTER........................................................5

3.1 Point numbering on the CSC chambers................................................................................. 5

3.2 Point numbering of the YE+1 ................................................................................................. 6

3.3 Alignment lines – description.................................................................................................. 8

3.4 Point numbering on the transfer plates ME+1 and targets................................................ 10

3.5 Point numbering and target on the sensor boxes for the CSC chambers ME+1/3 .......... 13

3.6 Point numbering and target on the sensor boxes ME12, ME11 and transfer plate......... 14

4 RESULTS – COORDINATES.......................................................................17

4.1 Coordinates – Reference points on YE+1 – Posts ............................................................... 17

4.2 Coordinates – Reference points on YE+1 – Green structure ............................................. 18

4.3 Coordinates of the points on the CSC chambers................................................................. 19

4.4 Coordinates and comparison – Line 15................................................................................ 25

4.5 Coordinates and comparison – Line 75................................................................................ 26

4.6 Coordinates and comparison – Line 135.............................................................................. 28







11 IINNTTRROODDUUCCTTIIOONN 1.1 Needs A photogrammetric measurement has been requested by Teresa RODRIGO and done on the Z- face of the Yoke Endcap YE+1 once the CSC Chambers and alignment system were installed. The goal of this measurement is to provide the 3D coordinates of the survey targets of all the devices installed on the Encap and in the Encap system. The measurement has been done on:

• The YE+1 reference points: the posts. • The welded points and coded points on the green structure. • The CSC chambers reference points. • The additional coded or no-coded targets • The alignment system devices reference points

1.2 Measurements The measurement took place in SX5 on the 21st of June 2006 and on the 4th of July 2006. The average RMS (one sigma) achieved for XYZ co-ordinates. This is the precision of the 3D coordinates measured at the centre of the survey target in the reference system.

Accuracy of the measurement RMS (XYZ): 0.3 mm All calculated 3D coordinates given correspond to the centre of the survey targets.




22 CCOOOORRDDIINNAATTEESS SSYYSSTTEEMM 2.1 Coordinate system The calculation has been done in the CMS system fixing given by the photogrammetry of the Yoke Endcap YE+1, made on the reference holes on the posts. For further details, please see the reports on EDMS: CMS-HE-UR-0013 version2 and CMS-SG-UR-0015.

Figure 1. Face view of the YE+1 Z- face

2.2 Calculation of 3D coordinates The coordinates have been calculated by a least square adjustment without constraints. The calculated coordinates have been transformed in the YE+1 CMS system by using a least square calculation adjustment without deformation.

All calculated coordinates are given as the centre of the survey targets.

X

Y




33 PPOOIINNTT NNUUMMBBEERRIINNGG AANNDD AADDAAPPTTEERR 3.1 Point numbering on the CSC chambers Measured points on CSC chambers and numbering

• A first one is a coded and permanent target. A code corresponds to a CSC chamber.

• Two other targets which are not coded but removable (button target). They equipped the reference holes of the CSC chamber. For a chamber called ME+1/X/YY, the two reference points are named YEP1_1XYY1 or YEP1_1XYY2, with 1 if the point is towards the centre of YE+1 and 2 in the other case.

X corresponds to the layer : 1 for inner and 2 for outer. YY corresponds to the number of the chamber: from 1 to 36 for inner, from 1 to 36 for outer. For example, the two reference points of the chamber ME+1/3/12 are named YEP1_13121 and YEP1_13122.

coded target YEP1_1XYY1YEP1_1XYY2

Chamber CSC ME+1/X/YY

Towrad YE+1 centre

Reference holeReference hole

Figure 2. Measured points on CSC chambers and numbering Photogrammetric button target with and without adapter

The reference holes of the CSC chambers are equipped with 6 mm pin button photogrammetric targets. These targets present a 5 mm offset with respect to the contact surface.

5 mm measured point:centre of

the target

pin: diameter 6 mm

Figure 3. Target for reference points on CSC chamber

The reference holes present a 6 mm diameter and there are not enough 6 mm pin targets to equip all points. That is why we also used an 8 mm diameter pin target with a 6 mm pin adapter: the offset of these targets values 3 mm and those of the adapters is 20 mm.




8H7 hole

diameter: 6 mm

20 mm

diameter: 6 mm

20 mm

3 mm

Figure 4. Target for reference points on CSC chamber

The measured point is the centre of the target.

3.2 Point numbering of the YE+1 The numbering used for the points on the YE+1 is those given in the previous measurement of the YE+1. For futher details, please see the EDMS report CMS-SG-UR-0015.

YEP1_3004

YEP1_3003

YEP1_3007

YEP1_3006

YEP1_3005

ME&RE+1/3/19ME&RE+1/3/01

ME&RE+1/2/18

ME&

RE+

1/3/

28M

E&R

E+1/

3/10

ME&

RE+

1/2/

10M

E&R

E+1/

2/28

ME&RE+1/3/02

ME&RE+1/3/23

ME&RE+1/3/05

ME&RE+1/3/32

ME&RE+1/2/14

ME&RE+1/2/14

ME&RE+1/2/32

ME&RE+1/2/24

ME&RE+1/2/06

YEP1_P_109

YEP1_P_088

YEP1_P_123

YEP1_P_122

YEP1_P_121YEP1_P_120

YEP1_P_119 YEP1_P_118

YEP1_P_117

YEP1_P_116

YEP1_P_115

YEP1_P_114

YEP1_P_113

YEP1_P_111

YEP1_P_112

YEP1_P_110


YEP1_P_106

YEP1_P_105

YEP1_P_104




YEP1_P_097

YEP1_P_096

YEP1_P_095


YEP1_P_092

YEP1_P_091

YEP1_P_090

YEP1_P_089

X

Y

YEP1_3014

YEP1_3010YEP1_3009

YEP1_3008

YEP1_3011

YEP1_3015

YEP1_3012YEP1_3013

YEP1_3002

YEP1_3001

YE+1face view

Figure 5. YE+1 reference points - posts




YE-1 reference points – targets and adapters for posts The posts are equipped with button photogrammetric targets with an adapter. The offset between the measured point and the contact surface values 8 mm. (3 mm for the target plus 5 mm for the adapter).

8H7 hole

5 mm

adapter

photogrammetric target

3 mm

Figure 6. Target and adapter for posts

The measured point is the centre of the target. YE+1 reference points – target and adapter for shoulders The shoulders are equipped with button photogrammetric target presenting a 20 mm offset with respect to the contact surface.

20 mm

measured point:centre of

the target

Figure 7. Target and adapter for shoulders





3.3 Alignment lines – description

Alignment line 15

Alignment line 75

Alignment line 135

Alignment line 195

Alignment line 255

Alignment line 315

Figure 8. Alignment lines on YE+1 The six concentric alignment lines have been installed. Each line is equipped with:

A transfer plate provided by David EARTLY. These transfer plates, named transfer plates ME+1, have been calibrated at CERN on February 2006: please see the EDMS report at the following address: CMS-ME-UR-0004.

Two sensor boxes also provided by David EARTLY and fixed to the chamber ME

RE+1/3.

Two sensor boxes (ME12_top and ME12_bottom) provided by Teresa RODRIGO is fixed to the chamber ME RE+1/2.

A transfer plate and a sensor box (ME11) also provided by Teresa RODRIGO is fixed to

YN1.




LINE 15

LINE 15

towards the centre of the YE+1Transfer Plate ME+1 PT1

ME+1/3/03 ME+1/3/03

LINE 75

ME+1/3/09

ME+1/3/09

ME+1/2/08

ME+1/2/08Transfer Plate ME+1 PT2

LINE 75

towards the centre of the YE+1

TP YN1

ME+1/1

LINE 135

ME+1/3/14


LINE 135


LINE 195

ME+1/3/20

ME+1/3/20

ME+1/2/20


LINE 195


LINE 255

ME+1/3/27

ME+1/3/27

ME+1/2/26


LINE 255


TP YN1

ME+1/1

LINE 315

ME+1/3/33

ME+1/3/33

ME+1/2/32


LINE 315


TP YN1

ME+1/1

Figure 9. Alignment lines on YE+1




3.4 Point numbering on the transfer plates ME+1 and targets The numbering used for the reference points of the transfer plates ME+1 is namely those defined during the calibration: please see report on EDMS, CMS-ME-UR-0004. The name of the EndCap, “YEP1_”, is added in front of each point number.

11091107

11081112

111311111103

t i f th t f l t

11021110

1101

11061104

1105

ME+1 PT1

1203

top view of the transfer-plate

1202

12101201

1206 1204

1205

12091207

12081212

12131211

ME+1 PT2

13091307

13081312

131313111303

1302

1310

1301

13061304

1305

ME+1 PT3

14091407

14081412

14131411

1403

140214101401

14061404

1405

ME+1 PT4




15091507

15081512

15131511

1503

1502

15011506

1504

1505

ME+1 PT5

16091607

16081612

16131611

1603

1602

1601

16061604

1605

ME+1 PT6

The transfer plates ME+1 have been calibrated at CERN on February 2006. The targets used for the calibration and for this measurement are the same. Please, see the report on EDMS CMS-ME-UR-0004. All the transfer plates have been equipped by David EARTLY. Points named from YEP1_XX01 to YEP1_XX03: 90 degrees target All the points, named from YEP1_1101 to YEP1_1103, from YEP1_1301 to YEP1_1303, from YEP1_1301 to YEP1_1303, from YEP1_1401 to YEP1_1403, from YEP1_1501 to YEP1_1503, and from YEP1_1601 to YEP1_1603, are measured with 90 degrees targets glued in the corresponding reference hole. There is no offset on the measurement of point with this sort of target.

measured point

Figure 10. Target used for YEP1_XX01, YEP1_XX02, and YEP1_XX03 points on Transfer Plates

The measured point is the centre of the target




Points named from YEP1_XX04 to YEP1_XX09: TBR 0.05-0.3-0.5 target All the points, named from YEP1_1104 to YEP1_1109, from YEP1_1304 to YEP1_1309, from YEP1_1904 to YEP1_1909, from YEP1_1404 to YEP1_1409, from YEP1_1504 to YEP1_1509, and from YEP1_1604 to YEP1_1609, are measured with TBR 0.05-0.3-0.5 targets. This target presents a 1.27 mm offset with respect to the surface contact.

1.27 mm measured point:centre of

the target

Figure 11. Target used for points named from YEP1_XX04 to YEP1_XX09 on Transfer Plates

The measured point is the centre of the target

Points named from YEP1_XX11 to YEP1_XX14: TBR 0.05-0.3-0.5 target Some additional points had been put on each transfer plate during the calibration. These points are materialized with stickers.

measured point:centre of

the target

Figure 12. Target used for points named from YEP1_XX11 to YEP1_XX14 on Transfer Plates





3.5 Point numbering and target on the sensor boxes for the CSC chambers ME+1/3 The reference points placed on the sensor boxes for the CSC chambers ME&RE+1/3 are numbered from YEP1_1XXX20 to YEP1_1XXX28, where XXX is the line number. For example, points on the sensor boxes on chamber 33 (line 315) are numbered from YEP1_131520 to YEP1_131525 for the first box and from YEP1_131526 to YEP1_131528 for the second one.

Sensor ME12 TOP from Teresa RODRIGO team.

ME+1/3/XX

YEP1_1XXX28

YEP1_1XXX26YEP1_1XXX27

YEP1_1XXX23

YEP1_1XXX25

YEP1_1XXX24

Transfer plate

ME+1/3/XX

YEP1_1XXX20YEP1_1XXX21

YEP1_1XXX22

Figure 13. Sensor boxes

Points from YEP1_1xxx20 to YEP1_1xxx25 are equipped with button photogrammetric target presenting a 1.27 mm offset from the contact surface.

1.27 mm measured point:centre of

the target

Figure 14. 1.27 mm button photogrammetric target

The three points YEP1_1xxx26, YEP1_1xxx27 and YEP1_1xxx28 are equipped with button photogrammetric target presenting a 5 mm offset from the contact surface.





the target

pin: diameter 6 mm

Figure 15. 5 mm button photogrammetric target


These devices have been equipped by David EARTLY. 3.6 Point numbering and target on the sensor boxes ME12, ME11 and transfer plate The numbering of all these points on sensor boxes and transfer plates has been defined by Teresa RODRIGO and Enrique CALVO ALAMILLO. Sensor boxes ME12_top and bottom:

Figure 16. Sensor boxes ME12_top and bottom

ME12_top ASPD

position 15º position 75º position 135º position 195º position 255º position 315ºPG target 1 1 5 9 13 17 21 PG target 2 2 6 10 14 18 22 PG target 3 3 7 11 15 19 23 PG target 4 4 8 12 16 20 24

All those points are numbered with the prefix YEP1_XXX_yyy

with XXX = 015°, 075°, 135°, 195°, 255°, 315° and yyy = 001 to 118.




ME12_bottom ASPD

position 15º position 75º position 135º position 195º position 255º position 315ºPG target 1 25 29 33 37 41 45 PG target 2 26 30 34 38 42 46 PG target 3 27 31 35 39 43 47 PG target 4 28 32 36 40 44 48

All those points are numbered with the prefix YEP1_XXX_yyy

with XXX = 015°, 075°, 135°, 195°, 255°, 315° and yyy = 001 to 118. Sensor box ME11 and transfer plate ME11

Figure 17. Sensor boxes ME11 and transfer plate ME11 Transfer plate ME11:

postion 15º postion 75º postion 135º postion 195º postion 255º postion 315ºPG target 1 49 57 65 73 81 89 PG target 2 50 58 66 74 82 90 PG target 3 51 59 67 75 83 91 PG target 4 52 60 68 76 84 92 PG target 5 53 61 69 77 85 93 PG target 6 54 62 70 78 86 94 PG target 7 55 63 71 79 87 95 PG target 8 56 64 72 80 88 96

All those points are numbered with the prefix YEP1_XXX_yyy with XXX = 015°, 075°, 135°, 195°, 255°, 315° and yyy = 001 to 118.




Sensor box ME11:

postion 15º postion 75º postion 135º postion 195º postion 255º postion 315ºPG target 1 97 101 105 109 113 117 PG target 2 98 102 106 110 114 118 PG target 3 99 103 107 111 115 119 PG target 4 100 104 108 112 116 120

All those points are numbered with the prefix YEP1_XXX_yyy with XXX = 015°, 075°, 135°, 195°, 255°, 315° and yyy = 001 to 118.

Targets used for Sensor boxes 11, 12 top and 12 bottom These sensor boxes have been equipped with button photogrammetric targets presenting a 3 mm offset with respect to the contact surface.


the target

Targets used for ME11 transfer plates On each transfer plate, reference holes named “PG target X” with X valuing 1, 5, and 7 have been equipped with a button photogrammetric target presenting a 3 mm offset from the contact surface. And the other reference holes, named “PG target Y” with Y valuing 2, 3, 4, 6 and 8 have been equipped with a 90 degrees photogrammetric target presenting a 15 mm offset with respect to the contact surface.

measured point

15 mm

The measured point is the centre of the target. All those points are numbered with the prefix YEP1_XXX_yyy

with XXX = 015°, 075°, 135°, 195°, 255°, 315° and yyy = 001 to 118.




44 RREESSUULLTTSS –– CCOOOORRDDIINNAATTEESS 4.1 Coordinates – Reference points on YE+1 – Posts

Coordinates measured on 2006 Coordinates measured on 2005 Comparison Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]

YEP1_P_088 4685.70 409.60 -728.50 YEP1_P_089 4863.91 1302.86 -631.72 4863.50 1302.60 -631.90 0.41 0.26 0.18 YEP1_P_090 4261.88 1987.08 -729.24 4261.50 1986.90 -728.90 0.38 0.18 -0.34 YEP1_P_091 4124.47 2887.56 -632.28 4124.30 2887.20 -632.40 0.17 0.36 0.12 YEP1_P_092 3325.33 3324.60 -730.37 3325.30 3324.30 -730.20 0.03 0.29 -0.17 YEP1_P_093 2887.66 4124.30 -632.64 2887.80 4123.50 -633.00 -0.14 0.80 0.36 YEP1_P_094 1987.00 4261.10 -731.50 YEP1_P_095 1303.17 4862.80 -633.95 1302.70 4862.70 -634.50 0.47 0.10 0.55 YEP1_P_096 410.37 4683.54 -731.43 409.90 4683.30 -731.20 0.47 0.24 -0.23 YEP1_P_098 -1217.60 4541.20 -731.00 YEP1_P_099 -2127.68 4562.32 -634.90 YEP1_P_100 -2697.16 3851.39 -730.32 -2696.80 3851.10 -730.20 -0.36 0.29 -0.12 YEP1_P_101 -3560.56 3559.60 -632.49 -3560.50 3559.60 -632.40 -0.06 0.00 -0.09 YEP1_P_102 -3853.18 2696.48 -729.52 -3852.70 2696.60 -729.40 -0.48 -0.12 -0.12 YEP1_P_103 -4563.58 2127.37 -632.10 -4563.30 2127.50 -631.90 -0.28 -0.13 -0.20 YEP1_P_104 -4542.68 1216.07 -729.17 -4542.20 1216.30 -728.90 -0.48 -0.23 -0.27 YEP1_P_105 -5016.12 438.84 -631.29 -5016.20 438.90 -631.10 0.08 -0.06 -0.19 YEP1_P_106 -4685.06 -410.23 -728.64 -4685.10 -409.80 -728.40 0.04 -0.43 -0.24 YEP1_P_107 -4863.49 -1302.61 -631.13 -4863.80 -1302.60 -631.30 0.31 -0.01 0.17 YEP1_P_108 -4262.18 -1986.40 -728.65 -4262.20 -1986.50 -728.40 0.02 0.10 -0.25 YEP1_P_109 -4124.50 -2887.30 -630.40 YEP1_P_110 -3325.00 -3324.18 -729.46 -3325.40 -3324.50 -729.10 0.40 0.32 -0.36 YEP1_P_111 -2887.70 -4121.56 -631.97 -2888.20 -4122.60 -631.90 0.50 1.04 -0.07 YEP1_P_113 -1302.67 -4862.33 -633.93 -1302.60 -4862.10 -633.90 -0.07 -0.23 -0.03 YEP1_P_114 -409.16 -4683.35 -729.22 -408.90 -4683.10 -729.10 -0.26 -0.25 -0.12 YEP1_P_115 438.81 -5013.75 -632.23 438.70 -5013.60 -632.30 0.11 -0.15 0.07 YEP1_P_116 1216.31 -4541.52 -729.80 1216.50 -4541.30 -731.20 -0.19 -0.22 1.40 YEP1_P_117 2127.95 -4560.92 -633.05 2128.00 -4560.90 -632.70 -0.05 -0.02 -0.35 YEP1_P_118 2697.39 -3850.82 -729.64 2697.80 -3850.60 -729.30 -0.41 -0.22 -0.34 YEP1_P_119 3559.69 -3559.50 -632.64 3559.90 -3559.50 -631.80 -0.21 0.00 -0.84 YEP1_P_120 3852.42 -2696.87 -729.29 3852.80 -2696.70 -728.70 -0.38 -0.17 -0.59 YEP1_P_121 4563.24 -2128.07 -631.26 4563.50 -2127.90 -630.90 -0.26 -0.17 -0.36 YEP1_P_122 4542.38 -1217.24 -728.48 4542.50 -1216.90 -728.60 -0.12 -0.34 0.12 YEP1_P_123 5015.94 -439.12 -631.16 5016.00 -445.00 -630.90 -0.06 5.88 -0.25 YEP1_P_124 4685.84 409.55 -728.56

points dX [mm] dY [mm] dZ [mm]Max 0.50 5.88 1.40 Min -0.48 -0.43 -0.84

Average -0.01 0.24 -0.09 Offset: 8 mm. Coordinates correspond to the centre of the target Apply an 8 mm correction in Z to get the value on the target contact surface




4.2 Coordinates – Reference points on YE+1 – Green structure Coordinates – Shoulders

Coordinates measured on 2006 Coordinates measured on 2005 Comparison Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]

YEP1_3000 -4659.70 5674.89 -759.49 -4658.80 5674.30 -760.10 -0.90 0.59 0.61 YEP1_3001 -4658.80 5674.30 -760.10 YEP1_3002 -6847.19 3049.73 -754.27 -6846.70 3049.70 -754.50 -0.49 0.03 0.23 YEP1_3003 -7453.61 1911.12 -762.77 -7453.10 1911.40 -763.00 -0.51 -0.28 0.23 YEP1_3004 -7450.73 -951.01 -758.94 -7451.00 -950.60 -759.30 0.27 -0.41 0.36 YEP1_3005 7196.79 2453.49 -751.84 7196.70 2454.20 -752.10 0.09 -0.71 0.26 YEP1_3006 7454.55 1294.92 -755.03 7455.40 1295.70 -754.90 -0.85 -0.78 -0.13 YEP1_3007 7450.30 -1165.10 -758.30 YEP1_3008 4959.70 -5743.60 -766.30 YEP1_3009 2671.60 -7062.30 -765.50 YEP1_3010 -2932.61 -6911.23 -761.89 -2933.50 -6913.00 -762.50 0.89 1.77 0.62 YEP1_3011 4630.80 5688.79 -759.32 4629.80 5688.80 -759.80 1.00 -0.01 0.48 YEP1_3012 2467.80 6936.10 -759.10 YEP1_3013 1465.80 7236.30 -760.10 YEP1_3014 -5114.84 -5653.97 -764.22 -5115.70 -5655.00 -764.70 0.86 1.03 0.48 YEP1_3015 5521.67 5341.95 -753.30

dX [mm] dY [mm] dZ [mm] Max 1.00 1.77 0.62 Min -0.90 -0.78 -0.13 Average 0.04 0.14 0.35

Offset: 20 mm. Coordinates correspond to the centre of the target Apply a 20 mm correction in Z to get the value on the target contact surface Coordinates – Coded targets

Points X [mm] Y [mm] Z [mm] YEP1_57 7372.04 -1186.97 -748.07 YEP1_58 7368.84 1274.43 -747.18 YEP1_59 7151.57 2364.36 -746.04 YEP1_60 2597.29 -7045.14 -754.88 YEP1_61 4923.97 -5621.38 -756.11 YEP1_62 -2857.00 -6773.92 -755.98 YEP1_57 7371.326 -1187.27 -748.958 YEP1_58 7368.134 1273.85 -747.634 YEP1_59 7151.097 2363.53 -746.236 YEP1_62 -2856.71 -6771.76 -756.259 YEP1_63 -5050.21 -5605.58 -752.426 YEP1_64 5460.249 5297.835 -748.75 YEP1_65 4709.286 5794.13 -750.006 YEP1_66 -7358.08 -980.097 -749.251 YEP1_67 -7348.68 1863.587 -754.113 YEP1_69 -5450.81 5297.531 -745.878 YEP1_70 -4737.83 5779.423 -748.065

Offset: 0.2 mm. Coordinates correspond to the centre of the target Apply a 0.2 mm correction in Z to get the value on the target contact surface




4.3 Coordinates of the points on the CSC chambers Coordinates – Reference points – chambers ME&RE+1/2/xx

Chambers Points X [mm] Y [mm] Z [mm] Offset [mm] ME&RE+1/2/01 YEP1_12011 2784.86 -0.16 -587.04 5.00 ME&RE+1/2/01 YEP1_12012 4591.05 -0.13 -586.77 23.00 ME&RE+1/2/02 YEP1_12021 2742.79 483.03 -860.98 5.00 ME&RE+1/2/02 YEP1_12022 4521.30 797.04 -860.38 23.00 ME&RE+1/2/03 YEP1_12031 2616.55 951.08 -586.29 5.00 ME&RE+1/2/03 YEP1_12032 4313.74 1569.41 -586.85 23.00 ME&RE+1/2/04 YEP1_12041 2411.51 1390.97 -860.90 5.00 ME&RE+1/2/04 YEP1_12042 3975.27 2294.50 -861.29 23.00 ME&RE+1/2/05 YEP1_12051 not measured - ME&RE+1/2/05 YEP1_12052 not measured - ME&RE+1/2/06 YEP1_12061 1789.71 2133.50 -861.28 5.00 ME&RE+1/2/06 YEP1_12061 not measured - ME&RE+1/2/07 YEP1_12071 not measured - ME&RE+1/2/07 YEP1_12072 not measured - ME&RE+1/2/08 YEP1_12081 952.54 2615.44 -861.77 5.00 ME&RE+1/2/08 YEP1_12082 1570.82 4312.24 -862.32 23.00 ME&RE+1/2/09 YEP1_12091 484.93 2740.98 -588.24 5.00 ME&RE+1/2/09 YEP1_12092 796.81 4519.52 -588.18 23.00 ME&RE+1/2/10 YEP1_12101 0.55 2785.60 -861.37 5.00 ME&RE+1/2/10 YEP1_12102 1.64 4591.90 -861.71 23.00 ME&RE+1/2/11 YEP1_12111 -482.50 2741.90 -587.65 5.00 ME&RE+1/2/11 YEP1_12112 -796.09 4520.13 -587.78 23.00 ME&RE+1/2/12 YEP1_12121 -952.90 2616.00 -862.18 5.00 ME&RE+1/2/12 YEP1_12122 -1571.14 4312.51 -862.50 23.00 ME&RE+1/2/13 YEP1_12131 -1392.41 2411.28 -587.68 5.00 ME&RE+1/2/13 YEP1_12132 -2296.38 3974.48 -588.18 23.00 ME&RE+1/2/14 YEP1_12141 -1789.74 2130.98 -862.13 5.00 ME&RE+1/2/14 YEP1_12142 -2951.80 3514.04 -864.64 23.00 ME&RE+1/2/15 YEP1_12151 -2133.61 1791.86 -585.76 5.00 ME&RE+1/2/15 YEP1_12152 -3518.00 2950.72 -586.26 23.00 ME&RE+1/2/16 YEP1_12161 -2410.71 1391.64 -861.12 5.00 ME&RE+1/2/16 YEP1_12162 -3975.73 2291.90 -860.47 23.00 ME&RE+1/2/17 YEP1_12171 -2616.38 951.80 -587.24 5.00 ME&RE+1/2/17 YEP1_12172 -4313.86 1567.84 -586.27 23.00 ME&RE+1/2/18 YEP1_12181 -2742.36 482.25 -865.08 5.00 ME&RE+1/2/18 YEP1_12182 -4520.75 796.80 -863.75 23.00 ME&RE+1/2/19 YEP1_12191 -2785.17 0.75 -596.91 5.00 ME&RE+1/2/19 YEP1_12192 -4591.41 0.01 -585.81 23.00 ME&RE+1/2/20 YEP1_12201 -2743.84 -483.66 -842.41 5.00 ME&RE+1/2/20 YEP1_12202 -4521.65 -797.41 -867.79 23.00 ME&RE+1/2/21 YEP1_12211 -2618.38 -951.87 -587.44 5.00 ME&RE+1/2/21 YEP1_12212 -4314.11 -1570.37 -585.46 23.00




Chambers Points X [mm] Y [mm] Z [mm] Offset [mm] ME&RE+1/2/22 YEP1_12221 -2413.72 -1393.58 -842.80 23.00 ME&RE+1/2/22 YEP1_12222 -3977.29 -2295.90 -847.28 23.00 ME&RE+1/2/23 YEP1_12231 -2132.93 -1788.74 -568.64 5.00 ME&RE+1/2/23 YEP1_12232 -3516.30 -2949.28 -574.82 23.00 ME&RE+1/2/24 YEP1_12241 -1789.85 -2134.35 -842.26 23.00 ME&RE+1/2/24 YEP1_12242 not measured - ME&RE+1/2/25 YEP1_12251 -1393.72 -2411.13 -569.24 5.00 ME&RE+1/2/25 YEP1_12252 -2294.85 -3975.39 -577.05 23.00 ME&RE+1/2/26 YEP1_12261 -952.51 -2616.23 -860.61 5.00 ME&RE+1/2/26 YEP1_12262 -1569.56 -4313.26 -861.48 23.00 ME&RE+1/2/27 YEP1_12271 -485.44 -2741.88 -586.59 5.00 ME&RE+1/2/27 YEP1_12272 -796.07 -4520.74 -587.53 23.00 ME&RE+1/2/28 YEP1_12281 -1.15 -2785.76 -860.08 5.00 ME&RE+1/2/28 YEP1_12282 -0.70 -4591.65 -860.34 23.00 ME&RE+1/2/29 YEP1_12291 483.54 -2742.67 -568.66 23.00 ME&RE+1/2/29 YEP1_12292 796.62 -4521.22 -575.19 23.00 ME&RE+1/2/30 YEP1_12301 952.68 -2617.50 -842.43 23.00 ME&RE+1/2/30 YEP1_12302 1569.32 -4314.43 -850.94 23.00 ME&RE+1/2/31 YEP1_12311 1391.59 -2413.16 -568.81 23.00 ME&RE+1/2/31 YEP1_12312 2296.02 -3976.38 -576.56 23.00 ME&RE+1/2/32 YEP1_12321 1790.33 -2133.03 -843.15 23.00 ME&RE+1/2/32 YEP1_12322 2951.47 -3516.00 -850.41 23.00 ME&RE+1/2/33 YEP1_12331 2133.04 -1790.36 -569.07 23.00 ME&RE+1/2/33 YEP1_12332 3516.50 -2951.14 -574.33 23.00 ME&RE+1/2/34 YEP1_12341 2412.88 -1392.35 -860.33 5.00 ME&RE+1/2/34 YEP1_12342 3976.76 -2295.09 -860.21 23.00 ME&RE+1/2/35 YEP1_12351 not measured - ME&RE+1/2/35 YEP1_12352 4313.96 -1570.05 -586.29 23.00 ME&RE+1/2/36 YEP1_12361 2743.97 -483.86 -860.97 5.00 ME&RE+1/2/36 YEP1_12362 4522.45 -798.22 -859.80 23.00

Offset: 23 or 5 mm Coordinates correspond to the centre of the target Apply a 23 or 5 mm correction in Z to get the value on the target contact surface




Coordinates – Reference points – chambers ME&RE+1/3/xx

Chambers Points X [mm] Y [mm] Z [mm] Offset [mm] ME&RE+1/3/01 YEP1_13011 5091.48 -0.87 -761.72 5.00 ME&RE+1/3/01 YEP1_13012 6795.55 -1.44 -761.81 23.00 ME&RE+1/3/02 YEP1_13021 5013.75 882.41 -763.02 5.00 ME&RE+1/3/02 YEP1_13022 6692.40 1177.92 -761.76 23.00 ME&RE+1/3/03 YEP1_13031 4784.97 1740.72 -763.62 5.00 ME&RE+1/3/03 YEP1_13032 6387.06 2322.39 -763.16 23.00 ME&RE+1/3/04 YEP1_13041 4410.33 2544.54 -763.68 5.00 ME&RE+1/3/04 YEP1_13042 5886.12 3397.08 -763.36 23.00 ME&RE+1/3/05 YEP1_13051 3900.75 3273.23 -764.25 5.00 ME&RE+1/3/05 YEP1_13052 5206.73 4367.31 -763.74 23.00 ME&RE+1/3/06 YEP1_13061 3273.37 3899.11 -763.65 5.00 ME&RE+1/3/06 YEP1_13062 4369.64 5204.38 -765.33 23.00 ME&RE+1/3/07 YEP1_13071 2544.57 4407.93 -764.24 5.00 ME&RE+1/3/07 YEP1_13072 3397.71 5883.19 -765.08 23.00 ME&RE+1/3/08 YEP1_13081 1742.45 4782.24 -764.76 5.00 ME&RE+1/3/08 YEP1_13082 Not measured - ME&RE+1/3/09 YEP1_13091 884.64 5011.83 -764.67 5.00 ME&RE+1/3/09 YEP1_13092 not measured - ME&RE+1/3/10 YEP1_13101 0.18 5090.19 -764.39 5.00 ME&RE+1/3/10 YEP1_13102 not measured - ME&RE+1/3/11 YEP1_13111 -882.93 5012.80 -764.54 5.00 ME&RE+1/3/11 YEP1_13112 not measured - ME&RE+1/3/12 YEP1_13121 -1741.93 4783.54 -764.46 5.00 ME&RE+1/3/12 YEP1_13122 -2324.15 6385.43 -764.61 23.00 ME&RE+1/3/13 YEP1_13131 -2544.93 4408.89 -764.57 5.00 ME&RE+1/3/13 YEP1_13132 -3397.81 5884.43 -764.09 23.00 ME&RE+1/3/14 YEP1_13141 -3273.18 3898.89 -762.99 5.00 ME&RE+1/3/14 YEP1_13142 -4368.35 5204.92 -763.58 23.00 ME&RE+1/3/15 YEP1_13151 -3900.89 3272.70 -763.53 5.00 ME&RE+1/3/15 YEP1_13152 -5206.14 4369.08 -763.21 23.00 ME&RE+1/3/16 YEP1_13161 -4408.36 2545.20 -763.75 5.00 ME&RE+1/3/16 YEP1_13162 -5884.69 3397.13 -763.15 23.00 ME&RE+1/3/17 YEP1_13171 -4784.05 1740.70 -763.43 5.00 ME&RE+1/3/17 YEP1_13172 -6386.47 2322.07 -762.03 23.00 ME&RE+1/3/18 YEP1_13181 -5014.58 883.68 -763.20 5.00 ME&RE+1/3/18 YEP1_13182 -6693.05 1178.92 -761.82 23.00 ME&RE+1/3/19 YEP1_13191 -5091.99 0.46 -763.27 5.00 ME&RE+1/3/19 YEP1_13192 -6796.12 -1.33 -762.31 23.00 ME&RE+1/3/20 YEP1_13201 -5015.27 -883.19 -762.33 5.00 ME&RE+1/3/20 YEP1_13202 -6693.51 -1181.05 -761.47 23.00 ME&RE+1/3/21 YEP1_13211 -4785.42 -1741.40 -745.71 23.00 ME&RE+1/3/21 YEP1_13212 -6386.52 -2324.35 -748.03 23.00 ME&RE+1/3/22 YEP1_13221 -4409.43 -2545.27 -745.03 23.00 ME&RE+1/3/22 YEP1_13222 -5885.32 -3396.57 -751.98 23.00 ME&RE+1/3/23 YEP1_13231 -3900.65 -3273.07 -744.27 23.00 ME&RE+1/3/23 YEP1_13232 -5206.84 -4367.17 -748.53 23.00




Chambers Points X [mm] Y [mm] Z [mm] Offset [mm] ME&RE+1/3/24 YEP1_13241 -3272.19 -3898.86 -743.25 23.00 ME&RE+1/3/24 YEP1_13242 -4368.45 -5203.07 -748.71 23.00 ME&RE+1/3/25 YEP1_13251 -2545.88 -4405.95 -746.60 23.00 ME&RE+1/3/25 YEP1_13252 -3397.08 -5882.09 -752.61 23.00 ME&RE+1/3/26 YEP1_13261 -1741.94 -4782.90 -764.91 5.00 ME&RE+1/3/26 YEP1_13262 -2324.51 -6384.81 -767.11 23.00 ME&RE+1/3/27 YEP1_13271 -883.11 -5014.44 -763.84 5.00 ME&RE+1/3/27 YEP1_13272 -1180.12 -6692.92 -765.84 23.00 ME&RE+1/3/28 YEP1_13281 -1.33 -5089.92 -763.23 5.00 ME&RE+1/3/28 YEP1_13282 32.66 -6990.27 -792.21 23.00 ME&RE+1/3/29 YEP1_13291 884.32 -5010.96 -748.02 5.00 ME&RE+1/3/29 YEP1_13292 1180.18 -6689.28 -752.69 23.00 ME&RE+1/3/30 YEP1_13301 1740.87 -4782.66 -748.15 23.00 ME&RE+1/3/30 YEP1_13302 2323.95 -6384.01 -754.24 23.00 ME&RE+1/3/31 YEP1_13311 2544.41 -4407.14 -745.23 23.00 ME&RE+1/3/31 YEP1_13312 3398.23 -5881.86 -752.40 23.00 ME&RE+1/3/32 YEP1_13321 3271.95 -3899.24 -745.59 23.00 ME&RE+1/3/32 YEP1_13322 4368.12 -5204.01 -750.74 23.00 ME&RE+1/3/33 YEP1_13331 3899.35 -3272.79 -745.22 23.00 ME&RE+1/3/33 YEP1_13332 5204.33 -4368.27 -749.09 23.00 ME&RE+1/3/34 YEP1_13341 4409.73 -2545.68 -763.20 5.00 ME&RE+1/3/34 YEP1_13342 5885.35 -3397.13 -762.36 23.00 ME&RE+1/3/35 YEP1_13351 4783.55 -1740.73 -763.68 5.00 ME&RE+1/3/35 YEP1_13352 6384.71 -2324.25 -762.80 23.00 ME&RE+1/3/36 YEP1_13361 5014.24 -884.47 -762.42 5.00 ME&RE+1/3/36 YEP1_13362 6692.51 -1180.74 -761.50 23.00

Offset: 23 or 5 mm Coordinates correspond to the centre of the target Apply a 23 or 5 mm correction in Z to get the value on the target contact surface




Coordinates – Coded targets – chambers ME&RE+1/2/xx

Chambers Points X [mm] Y [mm] Z [mm] ME&RE+1/2/01 none ME&RE+1/2/02 YEP1_38 3398.41 578.57 -794.98 ME&RE+1/2/03 none ME&RE+1/2/04 YEP1_39 3002.44 1714.30 -795.12 ME&RE+1/2/05 none ME&RE+1/2/06 YEP1_41 1206.51 3230.80 -794.29 ME&RE+1/2/07 none ME&RE+1/2/08 YEP1_42 22.00 3447.35 -795.57 ME&RE+1/2/09 none ME&RE+1/2/10 YEP1_43 -1165.56 3262.35 -795.96 ME&RE+1/2/11 none ME&RE+1/2/12 YEP1_44 -2223.71 2675.21 -795.55 ME&RE+1/2/13 none ME&RE+1/2/14 YEP1_45 -2982.05 1747.40 -795.07 ME&RE+1/2/15 none ME&RE+1/2/16 YEP1_46 -3416.87 626.34 -793.80 ME&RE+1/2/17 none ME&RE+1/2/18 YEP1_47 -3424.08 -579.83 -794.76 ME&RE+1/2/19 none ME&RE+1/2/20 YEP1_48 -2997.02 -1704.21 -794.32 ME&RE+1/2/21 none ME&RE+1/2/22 YEP1_49 -2233.59 -2636.15 -794.03 ME&RE+1/2/23 none ME&RE+1/2/24 YEP1_50 -1201.32 -3245.39 -794.65 ME&RE+1/2/25 none ME&RE+1/2/26 YEP1_51 -15.77 -3455.55 -794.50 ME&RE+1/2/27 none ME&RE+1/2/28 YEP1_52 1161.37 -3250.10 -795.37 ME&RE+1/2/29 none ME&RE+1/2/30 YEP1_53 2196.73 -2656.15 -795.11 ME&RE+1/2/31 none ME&RE+1/2/32 YEP1_54 2985.00 -1738.92 -795.09 ME&RE+1/2/33 none ME&RE+1/2/34 YEP1_55 3398.21 -613.91 -794.78 ME&RE+1/2/35 none ME&RE+1/2/36 YEP1_56 2228.54 2629.63 -795.16

Offset: 0.2 mm Coordinates correspond to the centre of the target Apply a 0.2 mm correction in Z to get the value on the target contact surface




Coordinates – Coded targets – chambers ME&RE+1/3/xx

Chambers Points X [mm] Y [mm] Z [mm] ME&RE+1/3/01 YEP1_2 5719.45 -101.24 -696.07 ME&RE+1/3/02 YEP1_3 5645.70 897.56 -695.54 ME&RE+1/3/03 YEP1_4 5381.93 1860.30 -697.44 ME&RE+1/3/04 YEP1_5 4954.69 2756.38 -697.34 ME&RE+1/3/05 YEP1_6 4402.53 3578.94 -698.39 ME&RE+1/3/06 YEP1_7 3706.17 4281.34 -698.69 ME&RE+1/3/07 YEP1_8 2901.32 4866.93 -699.52 ME&RE+1/3/08 YEP1_9 2021.34 5292.99 -699.06 ME&RE+1/3/09 YEP1_10 1091.53 5569.34 -699.06 ME&RE+1/3/10 YEP1_11 95.61 5670.04 -698.74 ME&RE+1/3/11 YEP1_12 -890.14 5606.37 -699.16 ME&RE+1/3/12 YEP1_13 -1851.31 5356.36 -698.04 ME&RE+1/3/13 YEP1_14 -2753.79 4958.53 -698.43 ME&RE+1/3/14 YEP1_15 -3572.71 4413.09 -698.39 ME&RE+1/3/15 YEP1_16 -4246.34 3750.96 -697.56 ME&RE+1/3/16 YEP1_17 -4855.18 2918.03 -697.22 ME&RE+1/3/17 YEP1_18 -5291.79 2026.19 -697.34 ME&RE+1/3/18 YEP1_19 -5565.57 1086.08 -696.26 ME&RE+1/3/19 YEP1_20 -5665.47 106.05 -696.48 ME&RE+1/3/20 YEP1_21 -5591.08 -877.79 -696.72 ME&RE+1/3/21 YEP1_22 -5353.01 -1844.35 -695.53 ME&RE+1/3/22 YEP1_23 -4997.75 -2719.50 -696.03 ME&RE+1/3/23 YEP1_24 -4398.58 -3562.41 -695.83 ME&RE+1/3/24 YEP1_25 -3703.72 -4278.25 -697.03 ME&RE+1/3/25 YEP1_26 -2914.25 -4852.64 -698.14 ME&RE+1/3/26 YEP1_27 -2017.52 -5286.86 -699.56 ME&RE+1/3/27 YEP1_28 -1062.84 -5565.86 -699.21 ME&RE+1/3/28 YEP1_29 -89.14 -5648.83 -698.80 ME&RE+1/3/29 YEP1_30 892.52 -5581.66 -699.40 ME&RE+1/3/30 YEP1_31 1848.19 -5339.11 -698.83 ME&RE+1/3/31 YEP1_32 2743.87 -4942.66 -699.10 ME&RE+1/3/32 YEP1_33 3564.95 -4385.94 -698.26 ME&RE+1/3/33 YEP1_34 4273.98 -3707.63 -697.45 ME&RE+1/3/34 YEP1_35 4863.14 -2902.55 -697.01 ME&RE+1/3/35 YEP1_36 5284.41 -2017.73 -697.24 ME&RE+1/3/36 YEP1_37 5553.99 -1073.04 -696.55





4.4 Coordinates and comparison – Line 15 Transfer plate ME+1 PT1:

Points X [mm] Y [mm] Z [mm] Offset [mm]YEP1_1101 7009.00 1674.97 -722.05 0.00 YEP1_1107 6908.71 1947.99 -818.59 1.27 YEP1_1108 6939.37 1926.22 -818.85 1.27 YEP1_1109 6923.67 1892.06 -818.44 1.27 YEP1_1111 6992.50 1980.31 -734.01 0.00 YEP1_1112 6974.02 1936.18 -733.99 0.00 YEP1_1113 7015.49 1908.71 -734.08 0.00

Offset: 0 or 1.27 mm Coordinates correspond to the centre of the target Apply a 0 or 1.27 mm correction in Z to get the value on the target contact surface Sensor boxes ME+1/3/03:

Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_101520 6585.76 1800.93 -819.20 1.27 YEP1_101521 6570.83 1856.90 -819.21 1.27 YEP1_101522 6555.11 1822.71 -819.00 1.27 YEP1_101523 4920.32 1356.22 -818.63 1.27 YEP1_101524 4905.28 1412.16 -818.53 1.27 YEP1_101525 4889.56 1377.94 -818.18 1.27 YEP1_101526 4555.08 1225.00 -847.03 5.00 YEP1_101527 4537.71 1323.51 -846.43 5.00 YEP1_101528 4433.14 1254.30 -846.50 5.00

Offset: 5 or 1.27 mm Coordinates correspond to the centre of the target Apply a 5 or 1.27 mm correction in Z to get the value on the target contact surface





Points X [mm] Y [mm] Z [mm] Offset [mm]YEP1_1202 1866.30 6960.55 -724.84 0.00 YEP1_1203 1731.52 6994.99 -677.25 0.00 YEP1_1207 1822.81 6942.19 -821.40 1.27 YEP1_1208 1801.23 6972.99 -821.49 1.27 YEP1_1209 1766.95 6957.50 -821.43 1.27 YEP1_1211 1858.66 7030.94 -736.51 0.00 YEP1_1212 1811.38 7007.21 -736.67 0.00 YEP1_1213 1787.15 7061.19 -736.63 0.00


Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_107520 1730.46 6603.84 -827.32 1.27 YEP1_107521 1674.61 6618.88 -826.40 1.27 YEP1_107522 1696.29 6588.23 -827.04 1.27 YEP1_107523 1285.06 4936.66 -820.59 1.27 YEP1_107524 1229.08 4951.50 -820.61 1.27 YEP1_107525 1250.89 4920.91 -820.18 1.27





Sensor boxes ME12 top and bottom, transfer plate on YN1 and sensor box ME11:

Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]YEP1_075_006 1277.61 4381.62 -931.45 1278.03 4383.28 -931.00 -0.42 -1.67 -0.45YEP1_075_007 1287.41 4454.85 -868.89 1287.26 4456.38 -868.00 0.15 -1.53 -0.89YEP1_075_008 1224.56 4395.98 -931.32 1224.90 4397.52 -931.00 -0.34 -1.53 -0.32YEP1_075_030 828.57 2704.96 -922.51 828.80 2706.74 -923.50 -0.22 -1.78 0.99YEP1_075_031 837.93 2778.29 -859.66 838.03 2779.84 -860.50 -0.10 -1.54 0.84YEP1_075_032 775.42 2719.33 -922.38 775.67 2720.97 -923.50 -0.25 -1.65 1.12YEP1_075_058 792.30 2683.33 -913.59 789.99 2685.54 -910.50 2.31 -2.22 -3.09YEP1_075_059 763.87 2603.31 -1042.96 763.16 2604.73 -1041.50 0.71 -1.43 -1.46YEP1_075_060 713.99 2704.87 -876.17 710.78 2706.77 -874.50 3.21 -1.90 -1.67YEP1_075_062 698.86 2619.85 -966.47 697.22 2621.37 -965.50 1.64 -1.52 -0.97YEP1_075_064 697.01 2619.97 -1104.35 697.22 2621.37 -1103.50 -0.21 -1.40 -0.85YEP1_075_101 769.38 2641.21 -1294.96 767.78 2641.29 -1290.00 1.60 -0.07 -4.96YEP1_075_102 777.37 2670.12 -1294.77 775.54 2670.26 -1290.00 1.83 -0.14 -4.77YEP1_075_103 738.82 2680.65 -1294.29 729.14 2651.64 -1290.00 9.68 29.01 -4.29

dX [mm] dY [mm] dZ [mm]Max 9.68 29.01 1.12Min -0.42 -2.22 -4.96

Average 1.40 0.76 -1.49

Comparison Meas. - Theo.Theoretical coordinatesMeasured coordinates

The theoretical coordinates have been provided by Teresa RODRIGO and Enrique CALVO ALAMILLO. Offset: please referee to part 3.6 of this report. Coordinates correspond to the centre of the target





Points X [mm] Y [mm] Z [mm] Offset [mm]YEP1_1301 -4995.79 5192.65 -675.74 0.00 YEP1_1302 -5094.41 5093.93 -723.34 0.00 YEP1_1307 -5008.57 5142.21 -819.38 1.27 YEP1_1308 -5046.05 5138.81 -819.42 1.27 YEP1_1309 -5049.55 5101.39 -819.51 1.27 YEP1_1311 -5071.85 5219.73 -734.86 0.00 YEP1_1312 -5078.11 5170.24 -734.85 0.00 YEP1_1313 -5127.43 5163.39 -734.79 0.00


Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_113520 -4760.90 4894.06 -820.33 1.27 YEP1_113521 -4801.86 4853.10 -820.48 1.27 YEP1_113522 -4764.32 4856.62 -820.35 1.27 YEP1_113523 -3542.72 3674.22 -818.55 1.27 YEP1_113524 -3583.54 3633.22 -818.83 1.27 YEP1_113525 -3546.06 3636.79 -818.35 1.27 YEP1_113526 -3222.86 3370.60 -848.12 5.00 YEP1_113527 -3291.74 3312.82 -847.47 5.00






Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_1403 -6908.48 -2052.58 -720.45 0.00 YEP1_1407 -6957.02 -1766.08 -817.15 1.27 YEP1_1408 -6972.84 -1800.18 -817.07 1.27 YEP1_1409 -6942.14 -1822.03 -817.06 1.27 YEP1_1411 -7055.67 -1782.40 -732.45 0.00 YEP1_1412 -7009.39 -1808.21 -732.41 0.00 YEP1_1413 -7040.49 -1855.27 -732.34 0.00


Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_119520 -6619.44 -1675.61 -817.93 1.27 YEP1_119521 -6604.26 -1731.48 -818.16 1.27 YEP1_119522 -6588.69 -1697.20 -818.11 1.27 YEP1_119523 -4954.41 -1228.50 -817.34 1.27 YEP1_119524 -4939.28 -1284.37 -817.59 1.27 YEP1_119525 -4923.67 -1250.10 -817.18 1.27

Offset: 5 or 1.27 mm Coordinates correspond to the centre of the target Apply a 5 or 1.27 mm correction in Z to get the value on the target contact surface Sensor boxes ME12 top and bottom, transfer plate on YN1 and sensor box ME11:

Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]YEP1_195_014 -4436.37 -1085.95 -930.01 -4435.05 -1084.84 -931.00 -1.33 -1.11 0.99YEP1_195_015 -4504.26 -1114.16 -866.72 -4502.97 -1113.39 -868.00 -1.29 -0.77 1.28YEP1_195_016 -4422.29 -1139.22 -929.75 -4420.81 -1137.97 -931.00 -1.48 -1.25 1.25YEP1_195_038 -2759.25 -635.60 -921.68 -2758.50 -635.61 -923.50 -0.74 0.01 1.82YEP1_195_039 -2827.26 -664.29 -859.03 -2826.43 -664.16 -860.50 -0.84 -0.13 1.47YEP1_195_040 -2745.06 -688.78 -921.56 -2744.27 -688.74 -923.50 -0.79 -0.05 1.94

dX [mm] dY [mm] dZ [mm]Max -0.74 0.01 1.94Min -1.48 -1.25 0.99

Average -1.08 -0.55 1.46

Measured coordinates Theoretical coordinates Comparison Meas. - Theo.






Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_1501 -2119.21 -6887.29 -729.04 0.00 YEP1_1503 -1730.59 -6991.64 -680.25 0.00 YEP1_1507 -1820.82 -6938.21 -823.65 1.27 YEP1_1508 -1799.11 -6968.85 -823.75 1.27 YEP1_1509 -1764.95 -6953.18 -823.55 1.27 YEP1_1511 -1856.00 -7030.00 -739.70 0.00 YEP1_1512 -1809.60 -7003.28 -739.40 0.00 YEP1_1513 -1779.85 -7054.15 -739.71 0.00


Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_125520 -1728.21 -6605.11 -832.54 1.27 YEP1_125521 -1672.38 -6619.96 -830.74 1.27 YEP1_125522 -1694.11 -6589.31 -831.51 1.27 YEP1_125523 -1283.80 -4939.30 -819.56 1.27 YEP1_125524 -1227.95 -4954.26 -819.82 1.27 YEP1_125525 -1249.67 -4923.53 -819.47 1.27 YEP1_125526 -1216.27 -4556.27 -847.71 5.00 YEP1_125527 -1122.40 -4590.47 -847.54 5.00 YEP1_125528 -1129.83 -4465.37 -847.40 5.00






Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]YEP1_255_018 -1277.34 -4382.92 -930.75 -1278.03 -4383.28 -931.00 0.69 0.36 0.25YEP1_255_019 -1286.61 -4456.15 -867.89 -1287.26 -4456.38 -868.00 0.64 0.23 0.11YEP1_255_020 -1224.21 -4397.04 -930.66 -1224.90 -4397.52 -931.00 0.69 0.48 0.34YEP1_255_042 -828.51 -2705.88 -921.33 -828.80 -2706.74 -923.50 0.29 0.86 2.17YEP1_255_043 -837.73 -2779.07 -858.75 -838.03 -2779.84 -860.50 0.30 0.77 1.75YEP1_255_044 -775.44 -2720.08 -921.66 -775.67 -2720.97 -923.50 0.23 0.89 1.84YEP1_255_082 -792.45 -2682.05 -908.31 -789.99 -2685.54 -910.50 -2.46 3.49 2.19YEP1_255_083 -764.28 -2602.29 -1039.00 -763.16 -2604.73 -1041.50 -1.12 2.45 2.50YEP1_255_084 -713.88 -2703.67 -871.47 -710.78 -2706.77 -874.50 -3.10 3.09 3.03YEP1_255_086 -698.97 -2618.88 -962.54 -697.22 -2621.37 -965.50 -1.76 2.49 2.96YEP1_255_088 -697.92 -2619.32 -1100.39 -697.22 -2621.37 -1103.50 -0.71 2.05 3.11

YEP1_255_0113 -769.08 -2641.99 -1294.80 -767.78 -2641.29 -1290.00 -1.30 -0.70 -4.80YEP1_255_0115 -730.37 -2652.53 -1294.83 -729.14 -2651.64 -1290.00 -1.24 -0.89 -4.83YEP1_255_0116 -738.34 -2681.52 -1294.84 -736.90 -2680.62 -1290.00 -1.43 -0.91 -4.84


Average -0.73 1.05 0.41







Points X [mm] Y [mm] Z [mm] Offset [mm]YEP1_1602 5094.24 -5092.99 -723.28 0.00 YEP1_1603 5192.37 -4994.45 -675.37 0.00 YEP1_1607 5101.20 -5047.62 -819.69 1.27 YEP1_1608 5138.66 -5044.11 -819.70 1.27 YEP1_1609 5142.20 -5006.70 -819.89 1.27 YEP1_1611 5167.34 -5119.60 -734.97 0.00 YEP1_1612 5160.23 -5068.69 -735.12 0.00 YEP1_1613 5218.29 -5069.87 -734.90 0.00


Points X [mm] Y [mm] Z [mm] Offset [mm] YEP1_131520 4853.50 -4801.29 -822.64 1.27 YEP1_131521 4894.32 -4760.29 -822.22 1.27 YEP1_131522 4856.89 -4763.89 -822.78 1.27 YEP1_131523 3634.32 -3582.07 -819.21 1.27 YEP1_131524 3675.18 -3541.11 -818.86 1.27 YEP1_131525 3637.73 -3544.63 -818.47 1.27 YEP1_131526 3338.77 -3331.14 -847.50 5.00 YEP1_131527 3415.34 -3266.84 -847.22 5.00 YEP1_131528 3303.05 -3210.89 -847.11 5.00






Points X [mm] Y [mm] Z [mm] X [mm] Y [mm] Z [mm] dX [mm] dY [mm] dZ [mm]YEP1_315_22 3158.01 -3297.46 -930.52 3157.02 -3298.44 -931.00 0.99 0.99 0.48YEP1_315_23 3216.73 -3342.17 -867.71 3215.71 -3342.99 -868.00 1.01 0.82 0.29YEP1_315_24 3196.81 -3258.39 -930.55 3195.91 -3259.55 -931.00 0.90 1.16 0.45YEP1_315_46 1929.35 -2070.42 -922.48 1929.71 -2071.13 -923.50 -0.36 0.71 1.02YEP1_315_47 1988.41 -2115.20 -859.60 1988.40 -2115.68 -860.50 0.01 0.47 0.90YEP1_315_48 1968.32 -2031.70 -922.56 1968.60 -2032.24 -923.50 -0.28 0.53 0.94YEP1_315_90 1926.31 -2030.44 -909.68 1930.76 -2026.92 -910.50 -4.44 -3.51 0.82YEP1_315_91 1871.77 -1965.71 -1040.34 1874.19 -1963.28 -1041.50 -2.42 -2.43 1.16YEP1_315_92 1984.15 -1973.27 -872.38 1988.74 -1968.94 -874.50 -4.59 -4.33 2.12YEP1_315_94 1918.48 -1917.67 -963.46 1921.56 -1914.49 -965.50 -3.08 -3.18 2.04YEP1_315_96 1920.40 -1916.94 -1101.45 1921.56 -1914.49 -1103.50 -1.16 -2.45 2.05YEP1_315_117 1902.96 -1987.12 -1292.01 1903.53 -1985.56 -1290.00 -0.57 -1.56 -2.01YEP1_315_118 1924.04 -2008.47 -1291.64 1924.75 -2006.77 -1290.00 -0.71 -1.71 -1.64YEP1_315_120 1952.49 -1980.16 -1291.55 1953.03 -1978.49 -1290.00 -0.54 -1.68 -1.55


Average -1.09 -1.15 0.50



Documents

CERN SX5 JUNE AND JULY 2006jnb/cms/docs/YE+1_photogrammetry_V...CMS – SX5 – YE+1 Photogrammetry YE+1 June and July 2006 CMS-SG-UR-0058 Version 2 2561_YEP1ZM_PG_V2.doc Page 3