FunctionThe CDT 30 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.

Applications• Damage service• Building drying• Water works• Dry storing

Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels

Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra

Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function

DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

CDT 30MOBILE DEHUMIDIFIER

FEATURES

MOBILE DEHUMIDIFIERS CDT

Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter

CDT 30

RAMIRENT

Specific energy consumption (SEC)• 0,45 kWh/l at 30°C & 80% RH• 0,81 kWh/l at 20°C & 60% RH

Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)

Also available in this series:CDT 30 SCDT 40CDT 40 SCDT 60CDT 90(see separate data sheets)

Model CDT 30Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 250 m³/hPower supply 230 V/50 HzMax. ampere consumption 2,7 AMax. power consumption 0,590 kWRefrigerant R 134aCompressor type RotarySound level (at 1 metre) 56 dB(A)Water container capacity 7 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 32 kg

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS

MOBILE DEHUMIDIFIERS CDT

Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.

AND WILL BE PROTECTED BY PATENTS

table LZT 142 0001, category

ohr

03-01-2012

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO

8Surface appearance according to reference BEND RADII:

ARE THE PROPERTY OF SAID COMPANY

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

650

506

427

Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.

AND WILL BE PROTECTED BY PATENTS

table LZT 142 0001, category

ohr

03-01-2012

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO

8Surface appearance according to reference BEND RADII:

ARE THE PROPERTY OF SAID COMPANY

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

650

506

427

Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.

AND WILL BE PROTECTED BY PATENTS

table LZT 142 0001, category

ohr

03-01-2012

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

65610.26g

SCALE: NOT TO SCALE

351 189

351189

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO

8Surface appearance according to reference BEND RADII:

ARE THE PROPERTY OF SAID COMPANY

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

REV.:

RE

V.:

CDT 30 MK II

CDT 30 MK II

PA

RT

NO

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

650

506

427

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,60

5

10

15

20

25

30

35°C

L/H

60%40% 80%

All dimensions are in mm.

736

650

426

RAMIRENT

FunctionThe CDT 40 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.

Applications• Damage service• Building drying• Water works• Dry storing

Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels

Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra

Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function

DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

CDT 40MOBILE DEHUMIDIFIER

FEATURES

MOBILE DEHUMIDIFIERS CDT

Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter

CDT 40

RAMIRENT

Specific energy consumption (SEC)• 0,50 kWh/l at 30°C & 80% RH• 0,66 kWh/l at 20°C & 60% RH

Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)

Also available in this series:CDT 30CDT 30 SCDT 40 SCDT 60CDT 90(see separate data sheets)

Model CDT 40Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 350 m³/hPower supply 230 V/50 HzMax. ampere consumption 3,6 AMax. power consumption 0,82 kWRefrigerant R 407CCompressor type RotarySound level (at 1 metre) 59 dB(A)Water container capacity 14 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 43 kg

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS

MOBILE DEHUMIDIFIERS CDT

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012

SCALE: NOT TO SCALE 351191

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191

only entended as a guide.

CDT 40 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

825

540

545

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012

SCALE: NOT TO SCALE 351191

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191

only entended as a guide.

CDT 40 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

825

540

545

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 40 MK II

ohr

93699.24g

BEND RADII:

24-05-2012

SCALE: NOT TO SCALE 351191

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191

only entended as a guide.

CDT 40 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

740

825

540

545

0

5

10

15

20

25

30

35°C

L/H

40% 60% 80%

0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8

All dimensions are in mm.

823

736

539

542

RAMIRENT

FunctionThe CDT 60 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.

Applications• Damage service• Building drying• Water works• Dry storing

Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels

Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra

Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function

DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

CDT 60MOBILE DEHUMIDIFIER

FEATURES

MOBILE DEHUMIDIFIERS CDT

Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter

CDT 60

RAMIRENT

Specific energy consumption (SEC)• 0,43 kWh/l at 30°C & 80% RH• 0,67 kWh/l at 20°C & 60% RH

Accessories½” drain outletRemote hygrostatWall bracketDual voltage kitCondensate pump in a cassette(see separate data sheet)

Also available in this series:CDT 30CDT 30 SCDT 40CDT 40 SCDT 90(see separate data sheets)

Model CDT 60Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 725 m³/hPower supply 230 V/50 HzMax. ampere consumption 4,9 AMax. power consumption 1,12 kWRefrigerant R 407cCompressor type RotarySound level (at 1 metre) 62 dB(A)Water container capacity 14 litresColour - water container and wheel cap RAL 7015Colour - front grille RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 47 kg

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS

MOBILE DEHUMIDIFIERS CDT

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.

CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

25-05-2012

SCALE: NOT TO SCALE

351 193

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

820

905

540

542

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.

CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

25-05-2012

SCALE: NOT TO SCALE

351 193

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

820

905

540

542

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.

CDT 60 MK II

99141.12g

BEND RADII:

CDT 60 MK II

ohr

351193

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)

25-05-2012

SCALE: NOT TO SCALE

351 193

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

820

905

540

542

0

5

10

15

20

25

30

35° C

L/H

40% 60% 80%

0 0,5 1,0 1,5 2,0 2,5 3,0

All dimensions are in mm.

903

816

539

RAMIRENT

FunctionThe CDT 90 is a robust, cost-effective and energy-efficient, reliable mobile de-humidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led to the drain.

Applications• Damage service• Building drying• Water works• Dry storing

Dehumidifier• High capacity• Low energy consumption• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Large wheels

Water drain• Fitted with a drain outlet for connection to a ½” water hose

Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function

DefrostingActive, demand-controlled defrosting which is activated through a tempera-ture sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

CDT 90MOBILE DEHUMIDIFIER

FEATURES

MOBILE DEHUMIDIFIERS CDT

Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter

CDT 90

RAMIRENT

Specific energy consumption (SEC)• 0,42 kWh/l at 30°C & 80% RH• 0,71 kWh/l at 20°C & 60% RH

AccessoriesRemote hygrostatDual voltage kit(see separate data sheet)

Also available in this series:CDT 30CDT 30 SCDT 40CDT 40 SCDT 60(see separate data sheets)

Model CDT 90Operating range – humidity 40-100% RHOperating range – temperature 3-32°CAir volume 1000 m³/hPower supply 230 V/50 HzMax. ampere consumption 7,2 AMax. power consumption 1,64 kWRefrigerant R 407cCompressor type RotarySound level (at 1 metre) 62 dB(A)Colour - wheel cap RAL 7015Colour - front grill RAL 7044Colour - control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel material PPControl panel material ABSWeight 62 kg

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

DIMENSIONS

MOBILE DEHUMIDIFIERS CDT

ohr

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011

SCALE: NOT TO SCALE 351194

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194

only entended as a guide.

CDT 90 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

895

980

593

650

ohr

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011

SCALE: NOT TO SCALE 351194

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194

only entended as a guide.

CDT 90 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

895

980

593

650

ohr

Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)

CDT 90 MK II

355066.95g

BEND RADII:

23-12-2011

SCALE: NOT TO SCALE 351194

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

PART NO REV.:

RE

V.:

PA

RT

NO

Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194

only entended as a guide.

CDT 90 MK II

8

Sheetmetal flatstate is based on Dantherm A/S process equipment and is

table LZT 142 0001, category Surface appearance according to reference

ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS

THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S

Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°

895

980

593

650

0

5

10

15

20

25

30

35° C

L/H

40% 60% 80%

0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5

All dimensions are in mm.

977

894

593

RAMIRENT