FunctionThe CDP 40T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.

Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias

POOL DEHUMIDIFIERS CDP

DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors

DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.

ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.

CDP 40T SWIMMING POOL DEHUMIDIFIER

FEATURES

Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal

cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion

resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected

to a ¾” hose• Outside connection to mains

Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water

heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)

Model CDP 40TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 400 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 3,8 AMax. power consumption 0,9 kWRefrigerant R407CQuantity of refrigerant 0,7 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 43 dB(A)Weight 57,5 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

INSTALLATION

POOL DEHUMIDIFIERS CDP

CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).

0

5

10

15

20

25

30

35

40

0 0,5 1,0 1,5 2,0 2,5

Temp. oC

L/H

CDP 40T

40% RH 60% RH 80% RH

Specific energy consumption (SEC): 0,47 kWh/l at 28°C & 60% RH

POOL DEHUMIDIFIERS CDP

DIMENSIONS CDP 40T

AccessoriesWireless remote control DRC1 Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter

dantherm.com

All dimensions are in mm.

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6

998 294

304

700

Drain outlet position

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6 430,7

50,6

The duct kit includes an extension for wall thickness from 70 to 366 mm.

A B C Wall opening

CDP 40T 465 998 642 610 x 110

Duct kits CDP 40T

c 80

146

106

235 73

FunctionThe CDP 50T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.

Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias

POOL DEHUMIDIFIERS CDP

DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors

DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.

ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.

CDP 50T SWIMMING POOL DEHUMIDIFIER

FEATURES

Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal

cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion

resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected

to a ¾” hose• Outside connection to mains

Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water

heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)

Model CDP 50TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 680 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 6,6 AMax. power consumption 1,5 kWRefrigerant R407CQuantity of refrigerant 0,9 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 44 dB(A)Weight 66 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4

dantherm.com

TECHNICAL DATA

CAPACITY CURVES

INSTALLATION

POOL DEHUMIDIFIERS CDP

CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).

0

5

10

15

20

25

30

35

40

0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0

Temp.

L/H

60% RH 80% RH

CDP 50T

40% RH

Specific energy consumption (SEC): 0,48 kWh/l at 28°C & 60% RH

°C

POOL DEHUMIDIFIERS CDP

DIMENSIONS CDP 50T

AccessoriesWireless remote control DRC1Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter

dantherm.com

All dimensions are in mm.

Duct kits CDP 50T

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6

1148 294

304

700

Drain outlet position

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6 430,7

50,6

The duct kit includes an extension for wall thickness from 70 to 366 mm.

A B C Wall opening

CDP 50T 616 1148 791 760 x 110

c 80

146

106

235 73

FunctionThe CDP 70T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.

Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias

POOL DEHUMIDIFIERS CDP

DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors

DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.

ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.

CDP 70T SWIMMING POOL DEHUMIDIFIER

FEATURES

Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal

cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion

resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected

to a ¾” hose• Outside connection to mains

Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water

heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)

Model CDP 70TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 900 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 8 AMax. power consumption 1,8 kWRefrigerant R407CQuantity of refrigerant 1,2 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 47 dB(A)Weight 77,5 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4

dantherm.com

TECHNICAL DATA

INSTALLATION

POOL DEHUMIDIFIERS CDP

0

5

10

15

20

25

30

35

40

0 1 2 3 4 5 6

Temp.

L/H

CDP 70T

40% RH 60% RH 80% RH

Specific energy consumption (SEC): 0,43 kWh/l at 28°C & 60% RH

CAPACITY CURVES

CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).

°C

POOL DEHUMIDIFIERS CDP

dantherm.com

All dimensions are in mm.

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6

1483 294

304

700

Drain outlet position

351 518

Surface appearance according to reference

CDP 70 T

1006419.82g

13-09-2016

"Thickness@@part1.SLDPRT"mm

351518

MATERIAL:

THICKNESS: WEIGHT:

REV. BY:

DATE:

REF.:

DATE:

REV.:

bof

Sheetmetal flatstate is based on Dantherm Air Handling A/S

All designs originated by Dantherm Air Handling A/S are the

table LZT 142 0001, category

PART NOproperty of said Company and will be protected by Patents.

8

SCALE: NOT TO SCALE

REV.:CDP 70 T

PAR

TN

O

process equipment and is only entended as a guide.

This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.

Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°

CDP 70 T 1483

CDP 50 T 1148

CDP 40 T 998

700

294

304

430,7

50,

6 430,7

50,6

DIMENSIONS CDP 70T

AccessoriesWireless remote control DRC1Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter

The duct kit includes an extension for wall thickness from 70 to 366 mm.

A B C Wall opening

CDP 70T 950 1483 1126 1095 x 110

Duct kits CDP 70T

c 80

146

106

235 73