CCNA 2 Praktice Exam Answer 90%

8/3/2019 CCNA 2 Praktice Exam Answer 90%

1/45

1 Top of Form

What are two switching functions of a router? (Choose two.)

The router encapsulates the packet in the appropriate data link frame type for the outgoing data link.

The router re-encapsulates the packet in a new frame, which results in a change of the Layer 2 header at each

hop.

The router determines the exit interface after data encapsulation.

The router changes the source logical address to the forwarding router interface logical address.

The router re-encapsulates the IP packet if no matching entry is found in the routing table and no defaultroute is configured.

Bottom of Form

2 Top of Form

Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once theadministrator is connected to the router, which password should the administrator enter at the R1> prompt toaccess the privileged EXEC mode?

Cisco001
http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml


2/45

Cisco123

Cisco789

Cisco901Bottom of Form

3 Top of Form

Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is trueregarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?

The router chooses the first path that it learned and installs only that route in the routing table.

The router chooses the path with the lowest administrative distance and installs only that route in the routingtable.

The router chooses the highest routing ID based on the advertised network IP addresses and installs only thatroute in the routing table.
http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml


3/45

The router installs all the equal cost paths in the routing table but sends packets out only one, holding theothers in reserve in case the primary route goes down.

The router installs all the equal cost paths in the routing table and performs equal cost load balancing to sendpackets out multiple exit interfaces.

Bottom of Form

4 Top of Form

Refer to the exhibit. The network administrator is planning IP addressing of a new network. What part of thisaddressing scheme must be changed to allow communication between host A and the server?

the IP address of the server

the default gateway of host A

the IP address of host A

the default gateway of the server


4/45

Bottom of Form

5 Top of Form

Refer to the exhibit. RIPv2 has been configured on routers R1 and R2. Users on LAN1 complain that they


5/45

cannot reach the users on LAN3. Which two commands should be applied to the configuration to remedy theproblem? (Choose two.)


6/45

Bottom of Form

6 Top of Form

A network administrator has enabled RIP on routers B and C in the network diagram. Which of the followingcommands will prevent RIP updates from being sent to Router A?

A(config)# router ripA(config-router)# passive-interface S0/0

B(config)# router ripB(config-router)# network 192.168.25.48B(config-router)# network 192.168.25.64


7/45

A(config)# router ripA(config-router)# no network 192.168.25.32

B(config)# router ripB(config-router)# passive-interface S0/0

A(config)# no router rip

Bottom of Form

7 Top of Form

What are two functions of a router? (Choose two.)

It connects multiple IP networks.

It controls the flow of data via the use of Layer 2 addresses.

It determines the best path to send packets.

It manages the VLAN database.

It increases the size of the broadcast domain.

Bottom of Form

8 Top of Form


8/45

Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface ofRouter2 in order to put the interface in the same network as the serial interface of Router1?

IP 172.16.0.18, subnet mask 255.255.255.0

IP 172.16.32.15, subnet mask 255.255.255.240

IP 172.16.0.18, subnet mask 255.255.255.252

IP 172.16.32.18, subnet mask 255.255.255.252

Bottom of Form

9 Top of Form


9/45

Refer to the exhibit. Hosts on the BOS Fa0/0 LAN are able to ping the Fa0/1 interface on the JAX router and allinterfaces on the BOS and ORL routers. Why would hosts from the 10.0.0.0/24 network not be able to ping hostson the Fa0/0 LAN of the JAX router?

The JAX router has the wrong process ID.

The JAX router needs the network 10.0.0.0 0.0.0.255 area 0 command.

The JAX router needs the network 192.168.3.0 0.0.0.255 area 0 command.

The BOS router needs the network 192.168.3.0 0.0.0.255 area 0 command.

Bottom of Form

10 Top of Form


10/45

Refer to the exhibit. What information can be determined from the highlighted output?

R1 is originating the route 172.30.200.32/28.

Automatic summarization is disabled.

The 172.30.200.16/28 network is one hop away from R1.

A classful routing protocol is being used.

Bottom of Form

11 Top of Form


11/45

Refer to the exhibit. What needs to be done to allow these two routers to connect successfully?

Add a clock rate to S0/0/0 on R1.

Add an interface description to S0/0/1 on R2.

Change the serial interface on R2 to S0/0/0 so that it matches R1.

Change the IP address of S0/0/1 on R2 so that it is in the same subnet as R1.

Bottom of Form

12 Top of Form


12/45

Refer to the exhibit. What OSPF networkstatements are required for the router B to advertise the threenetworks that are attached?

router ospf 1network 10.0.0.0 0.0.0.255 area 0

router ospf 1

network 10.1.1.0 0.3.255.255 area 0network 10.10.1.0 0.255.255.255 area 0network 10.20.1.0 0.255.255.255 area 0



13/45

network 10.10.1.0 0.0.255.255 area 0network 10.20.1.0 0.0.255.255 area 0


network 10.10.1.0 0.0.0.255 area 0network 10.20.1.0 0.0.0.255 area 0

Bottom of Form

13 Top of Form


14/45

Refer to the exhibit. A network designer is testing a prototype of WAN connections. All of the routers in theexhibit are configured for OSPF routing. The design requires that the path between routers A and D through ISP-A is the primary and the path through ISP-B servers as a backup. The designer notices that router A has twoequal-cost paths to the LAN on router D. How can the designer correct this problem?

Issue a clock rate 2000000 interface command on S0/0/1 of router ISP-B.

Change the default OSPF reference bandwidth on router A.

Configure two static routes with administrative distances of 10.


15/45

Use the bandwidth command to change the default bandwidth on the link to router B.

Bottom of Form

14 Top of Form

Because of a topology change, the next hop IP address in the current static route must be reconfigured. How cana static route entry be altered to accommodate a topology change?

Keep the existing static route and configure a new static route with the correct next hop IP address.

Negate the existing static route and configure a new static route with the correct next hop IP address.

Do nothing. The existing static route will automatically update the next hop entry with the new IP address.

Keep the existing static route, reload the router, and configure a new static route with the correct next hop IPaddress.

Bottom of Form

15 Top of Form


16/45

Refer to the exhibit. Based on the output from the show running-config and debug ip rip commands, what aretwo of the routes that are added to the routing table of R1? (Choose two.)

R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1

R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0

S 192.168.1.0/24 [1/0] via FastEthernet0/0

R 192.168.9.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/0

R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0

Bottom of Form


17/45

16 Top of Form

Refer to the exhibit. All routers are configured with RIPv2 active on all interfaces. Automatic summarization isin effect. Why does the routing table on R3 include the 209.165.200.228/30 network but not the 172.30.1.0/24and 172.30.2.0/24 networks?

CIDR is required to route supernets.

There is no default gateway configured.

The 172.30.0.0/16 subnets are discontiguous.

RIPv2 cannot route networks with variable subnets.


18/45

Bottom of Form

17 Top of Form

Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this?

The two routers are connected on a multiaccess network.

The hello and dead intervals are different on the two routers.

They have different OSPF router IDs.

They have different process IDs.

Bottom of Form


19/45

18 Top of Form

What is the function of the OSPF LSR packet?

It is used to confirm the receipt of LSUs.

It is used to establish and maintain adjacency with other OSPF routers.

It is used by the receiving routers to request more information about any entry in the DBD.

It is used to check the database synchronization between routers.

Bottom of Form

19 Top of Form

Which network design feature requires the deployment of a classless routing protocol?

private IP addressing

advertising default routes

variable length subnet masks

summarization on major network boundaries

Bottom of Form

20 Top of Form
http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml


20/45

Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distancevalues. All devices are properly configured and the destination network is advertised by both protocols.

Which path will be used to transmit the data packets from PC1 to PC2?

The packets will travel via R2-R1.

The packets will travel via R2-R3.

The traffic will be load-balanced between two paths via R2-R1 and via R2-R3.

The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the backup path.

Bottom of Form

21 Top of Form

A router has EIGRP configured as the only routing protocol. In what way might EIGRP respond if there is no


21/45

feasible successor route to a destination network and the successor route fails?

It broadcasts hello packets to all routers in the network to re-establish neighbor adjacencies.

It sends queries to adjacent neighbors until a new successor route is found.

It immediately sends its entire routing table to its neighbors.

It will set the metric for the failed route to infinity.

Bottom of Form

22 Top of Form

Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?

It is the value assigned by the Dijkstra algorithm that designates the number of hops in the network.

It is the value used by the DUAL algorithm to determine the bandwidth for the link.

It is the metric, which is cost.

It is the administrative distance.


22/45

Bottom of Form

23 Top of Form

Refer to the exhibit. All router interfaces are configured with an IP address and are operational. If no routingprotocols or static routes are configured, what information will be included in the show ip route command

output for router A?

All of the 192.168.x.0 networks will be in the routing table.

Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24 will be in the routing table.

The routing table will be empty because routes and dynamic routes have not been configured.

A default route is automatically installed in the routing table to allow connectivity between the networks.

Bottom of Form

24 Top of Form


23/45

Refer to the exhibit. The network administrator issues the command no ip classless on Router1. Whatforwarding action will take place on a packet that is received by Router1 and is destined for host 192.168.0.26?

The packet will be dropped.

The packet will be forwarded to the gateway of last resort.

The packet will match the 192.168.0.0 network and be forwarded out Serial 0/0.

The packet will most closely match the 192.168.0.8 subnet and be forwarded out Serial 0/1.

Bottom of Form

25 Top of Form

Using default settings, what is the next step in the router boot sequence after the IOS loads from flash?

Perform the POST routine.

Search for a backup IOS in ROM.

Load the bootstrap program from ROM.


24/45

Load the running-config file from RAM.

Locate and load the startup-config file from NVRAM.

Bottom of Form

26 Top of Form

Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet network attached to R3. R1learned Path A to network 10.2.0.0/16 from a static route and Path B to network 10.2.0.0/16 from EIGRP. Whichroute will R1 install in its routing table?

Both routes are installed and load balancing occurs across both paths.

The route via Path B is installed because the EIGRP route has the best metric to network 10.2.0.0/16.

The route via Path A is installed because the static route has the best metric to network 10.2.0.0/16.


25/45

The route via Path B is installed because the EIGRP route has the lowest administrative distance to network10.2.0.0/16.

The route via Path A is installed because the static route has the lowest administrative distance to network10.2.0.0/16.

Bottom of Form

27 Top of Form

What command would the network administrator apply to a router that is running OSPF to advertise the entirerange of addresses included in 172.16.0.0/19 in area 0?

R1(config-router)# network 172.16.0.0 0.0.0.255 area 0




Bottom of Form

28 Top of Form


26/45

Refer to the exhibit. How many routes are child routes?

1

3

4

6

Bottom of Form

29 Top of Form

Which router mode is accessed by entering the enable command?

user EXEC

privileged EXEC

global configuration

interface configuration

Bottom of Form

30 Top of Form


27/45

Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding trafficbetween BR and HQ?

RIP

RIPv2

EIGRP

static routes

Bottom of Form

31 Top of Form


28/45

Refer to the exhibit. When a static IP address is being configured on the host, what address should be used forthe default gateway?

10.1.1.1

10.1.1.2

172.16.1.1

192.168.1.1

Bottom of Form

32 Top of Form


29/45

Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running theEIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but theycannot form an EIGRP neighbor adjacency.

What action should be taken to solve this problem?

Enable the serial interfaces of both routers.

Configure EIGRP to send periodic updates.

Configure the same hello interval between the routers.

Configure both routers with the same EIGRP process ID.

Bottom of Form


30/45

33 Top of Form

Refer to the exhibit. Routers RTRA and RTRB are running OSPF. What entry does RTRA add in the routingtable when Serial 0/0/0 receives an update about the network that is attached to RTRB?

O 172.16.7.0/30 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0

O 172.16.7.16/28 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0

O 172.16.7.0/24 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0

O 172.16.0.0/16 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0

Bottom of Form

34 Top of Form


31/45

Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hostson the Internet fail. What is the reason for this problem?

The FastEthernet interface of R1 is disabled.

One of the default routes is configured incorrectly.

A routing protocol is not configured on both routers.

The default gateway has not been configured on host A.


32/45

Bottom of Form

35 Top of Form

Refer to the exhibit. All interfaces are configured with the correct IP addresses and subnet masks. OSPF hasbeen configured as the routing protocol. During troubleshooting, it is determined that hosts on network B canping the Lo0 interface on R1 but are unable to reach hosts on network A. What is the cause of the problem?

Routers R1 and R2 have incorrect router IDs configured.

Router R1 is unable to form a neighbor relationship with router R2.


33/45

Routers R1 and R2 have been configured in different OSPF areas.

The configuration of router R1 fails to include network A in the OSPF routing process.

Bottom of Form

36 Top of Form

Refer to the exhibit. All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable toaccess each other. What can be the cause of this problem?

Because RIPv1 is a classless protocol, it does not support this access.

RIPv1 does not support discontiguous networks.


34/45

RIPv1 does not support load balancing.

RIPv1 does not support automatic summarization.

Bottom of Form

37 Top of Form

Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRPon the Paris router? (Choose three.)

Paris(config)# router eigrp 100

Paris(config)# router eigrp

Paris(config-router)# network 192.168.6.0



35/45



Bottom of Form

38 Top of Form

What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency?(Choose two.)

The routers must elect a designated router.

The routers must agree on the network type.

The routers must use the same dead interval.

The routers must exchange link state requests.

The routers must exchange database description packets.

Bottom of Form

39 Top of Form


36/45

Refer to the exhibit. A network engineer has run the show version command on R3. Upon rebooting, R3 doesnot load the start-up configuration settings.

What could be the cause of this problem?

There is insufficient NVRAM.

There is insufficient flash memory.

The configuration register is not configured with the default setting.

The system image file is not located in NVRAM.

Bottom of Form

40 Top of Form


37/45

Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which

two facts are true about the forwarding of route information by R1? (Choose two.)

R1 will forward the route information for subnet 192.168.100.0/30.

R1 will not forward route information for subnet 192.168.100.4/30.

R1 will forward the route information with an administrative distance set to 50.

R1 will forward the summarized route information for network 192.168.100.0/24.

R1 will forward route information for subnet 10.10.10.0/30 out the serial interface.

Bottom of Form

41 Top of Form


38/45

Refer to the exhibit. All routes are advertised and fully operational on all routers. Which statement is true about

the path that the data will take from router A to router B?If EIGRP is used with default configurations, the data will be equally distributed between two paths A, D,B and A, C, B.

If RIPv1 is used with default configurations, the data will be load-balanced on all paths.

If EIGRP and OSPF are both used with default configurations, the data will be sent through paths learned bythe OSPF protocol.

If RIPv2 is used with default configurations, the data will be equally distributed between two paths A, D,B and A, C, D.

Bottom of Form

42 Top of FormHow does route poisoning prevent routing loops?

New routing updates are ignored until the network has converged.


39/45

Failed routes are advertised with a metric of infinity.

A route is marked as unavailable when its Time to Live is exceeded.

The unreachable route is cleared from the routing table after the invalid timer expires.

Bottom of Form

43 Top of Form

Refer to the exhibit. A network administrator has configured R1 as shown, and all interfaces are functioningcorrectly. A ping from R1 to 172.16.1.1 fails. What could be the cause of this problem?

The serial interface on R1 is configured incorrectly.


40/45

The default route is configured incorrectly.

The default-information originate command must be issued on R1.

Autosummarization must be disabled on R1.

Bottom of Form

44 Top of Form

A network is configured with the IP, IPX, and AppleTalk protocols. Which routing protocol is recommended forthis network?

RIPv1

RIPv2

EIGRP

OSPF

Bottom of Form

45 Top of Form


41/45

Refer to the exhibit. Which network command will prevent EIGRP on router RA from advertising the Ethernetnetworks but will allow the advertisement of all networks on the WAN links?

RA(config-router)# network 172.16.1.0 0.0.0.0





Bottom of Form

46 Top of Form


42/45

Which two statements are true regarding link-state routing protocols? (Choose two.)

They are aware of the complete network topology.

They offer rapid convergence times in large networks.

They do not include subnet masks in their routing updates.

They rely on decreasing hop counts to determine the best path.

They do not work well in networks that require special hierarchical designs.

They pass their entire routing tables to their directly connected neighbors only.

Bottom of Form

47 Top of Form

Which router component is used to store the routing table?Flash

NVRAM

ROM

SDRAM

Bottom of Form

48 Top of Form


43/45

Refer to the exhibit. What summarization should R2 use to advertise its LAN networks to R1?

172.16.0.0/24

172.16.4.0/22

172.16.4.0/23

172.16.4.0/24

Bottom of Form

49 Top of Form


44/45

Refer to the exhibit. What happens to a packet that has 172.16.0.0/16 as the best match in the routing table that isshown?

The packet is discarded.

The packet is flooded out all interfaces.

The packet is forwarded via Serial0/0/0.

The packet is forwarded via FastEthernet0/0.

Bottom of Form

50 Top of Form

A router that is using RIPv2 learns of the network 10.10.10.0/24 from two different neighbors. Which value is

used by RIPv2 to select the best path to the network?route metric

subnet mask


45/45

longest match

administrative distance

Bottom of Form

Documents

CCNA 2 Praktice Exam Answer 90%