CCIE RS v5.0 LAB Exam Precautions - SPOTO · H1：crypto isakmp key CCIE address 0.0.0.0 H1+ crypto keyring DMVPN vrf LOCALSP pre-shared-key address 0.0.0.0 0.0.0.0 key CCIE About

SPOTO IT人才培训机构 www.SPOTO.net 以伙伴关系帮助客户成功，帮助员工成功，帮助合作伙伴成功。SPOTO IT人才培训机构 www.SPOTO.net 以伙伴关系帮助客户成功，帮助员工成功，帮助合作伙伴成功。

CCIE RS v5.0 LAB Exam Precautions

SPOTO CCIE Club R&S V5.0

SPOTO IT人才培训机构 www.SPOTO.net 以伙伴关系帮助客户成功，帮助员工成功，帮助合作伙伴成功。

TS

Enter your desktop email and passwordto start the CCIE exam.


TS


TS


TS


TS


TS


TS


DIAG


DIAG


DIAG


DIAG


DIAG


TS Precautions• Seriously examine questions, which equipment can not be modified or can not be

deleted

• Each questions takes up to 8mins ,if don’t get out put , remember this questions on

txt file, do next questions.

• Do the simple questions first

• When you finish all questions, need check the out put again, and all device “write”

config again(must need to do)

• If this faults don’t make sure, remember it on txt, if it invalid changes, you will need

to restore

• Maye will face different IP address on really exam, show ip first

• BGP should be “clea ip bgp *”when you changed about BGP config

• Remember to write config

• When you finish all questions, write the config again on all device

• If you enable : logging console、logging on，you will need close them when you

finish all questions.


TS Precautions

• Text back path, if you don’t have enough time, don’t need to test, Ensure that the

main path is positive.

• Pay attention to control time,Stuck for more than 30 minutes to decisively skip doing

the back.


DIAG Precautions

• Read the all materials first , then start to do.

• Before choose , confirm whether the answer is correct

• When you recheck, choose device will need reselected

• If can’t select, select other device , then select correct device If face same answer ,

choose one will be ok.


CFG Precautions• The ip address maybe will defferent, show the ip address first

• Check every section when you finish this section config（show run + 现象）

• When you finish all section, check all section output again. And write all device config.

• All device will need write config, when you end some config. After Finish all config

should be write again 。

• IF some device face some BUG, like Direct connection is impossible but condif is corrct

:

1、shutdown no shutdown interface first，

2、IF also not up, check the config, ACL, IGP, or default this interface , config

again(copy the ip address and important config first)

3、If default also can‘t solve it , wite config , then reload this Device

4、Also can’t , copy this device all config to txt file , then default this device ,

config again.

5、IF BUG also have , write this area device config , then reload this Area all

device . Also can ask proctor 。

The time to handle BUG by yourself is controlled within 30min~60min


CFG Precautions

• When You finish every section, check output and status.

• BGP need remember “clea ip bgp * so or clea ip bgp *”

• Before config about yourself, check the preconfig first.

• When you plan config NAT , cost need config NAT device, because config NAT will be

slow. You can config NAT first , if very slow ,do other section

• If you Did not complete all Section， don’t enter “End session”

• *Jan 3 03:56:29.401: %AMDP2_FE-6-EXCESSCOLL: Ethernet2/0 TDR=0, TRC=0 When

you see this log message , reload this device.


CFG Precautions

When you config DMVPN, maybe will face BUG, make DMVPN not up

1、Before config Ipsec , shutdown the tunnel interface

2、Remember how to solve DMVPN issue .

3、Ipsec password check more time , not have Space end of password

4、IF DMVPn is UP , when you call Ipsec, the DMvpn can‘t up , no ipsec , or don’t call

Ipsec , also can pass.

5、If DMVPN does not always work, the default interface, and then the shutdown

interface, configure the brush into it, repeat several times until the neighbors can get up.

When you config ip nat outside , maybe the BGP neighbor will down, can config NAT first.

6、Default 4 times


CFG Precautions

H1：crypto isakmp key CCIE address 0.0.0.0

H1+

crypto keyring DMVPN vrf LOCALSP

pre-shared-key address 0.0.0.0 0.0.0.0 key CCIE

About these command , can’t copy ,need config about yourslef.

When you plan end the lab exam , need make sure can get all output if you have enough

time.

All de

Need write config first :Router#verify /md5 nvram:startup-config


1、Trouble

• 1、How to know proctor give you some trouble

• Check the MD5 value

• Repeatedly testing the main output

• 2、when you plan end this exam , to ask the proctor first , then end it.

When you end this exam , test all output again , then end this exam.


Never give up

• Keep in touch at all times (on the morning of the exam,

remember to check Skype before going to the exam room.

Is there any message?)

• Drink some refreshing drinks ， Breakfast is full.

• Delay in the examination room may be relatively large

• If the exam is tight, take a deep breath

• Don't give up


Never give UP

The winner will never give up, and the abandoner will never succeed！


Check Score

• When you end the exam, contact with Tutor.

• Check score, when you received email from cisco, then login

the website to seach. Can’t use Ipad to check score.


3Pass

• Don't offend the Proctor， Don't ask proctor very easy

questions.

Documents

CCIE RS v5.0 LAB Exam Precautions - SPOTO · H1：crypto isakmp key CCIE address 0.0.0.0 H1+ crypto keyring DMVPN vrf LOCALSP pre-shared-key address 0.0.0.0 0.0.0.0 key CCIE About