© 2012 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION Ltd. retains all rights not expressly granted.This publication is RADVISION confidential. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by RADVISION Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by RADVISION Ltd. or its agents. RADVISION Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. RADVISION Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact RADVISION Ltd. and a copy will be provided to you. Unless otherwise indicated, RADVISION registered trademarks are registered in the United States and other territories. All registered trademarks recognized. All right reserved.For further information contact RADVISION or your local distributor or reseller. http://www.radvision.com

System Installation and ActivationConnect all cables to the SCOPIA XT4000 series Codec Unit (see overleaf). Power supply must be connected after all other connections have been established.1. Turn on the TV monitors. Monitor on HDMI1 is mandatory, monitor HDMI2 is optional.2. Make sure the remote control has batteries installed.3. Verify that the LED on the front panel of the Codec Unit is turned on.4. If the codec unit does not turn on automatically, press the 5. button on the remote control. The graphical menu appears on the monitors.6.

A

Moving the Camera On the general screen, 1. navigate to Control Camera using the arrow keys and press OK.Use the arrow keys to move 2. the camera to the preferred position. Press Back when done.3.

G

CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.

Network SettingsEnter your network settings. 1. For questions about this information, consult your system administrator. Then select Next.2.

Gatekeeper Settings Enter your Gatekeeper settings 1. and your E.164 number. For questions about this information, consult your system administrator. Then select Done.2.

E F

Country and Language of Interface

System Name field displays the 1. name of this Codec Unit as displayed in a video conference, for example:

Hong Kong, • or 9th Floor Conf Rm •

Use the remote control keypad 2. to type the name. Press OK to toggle letters or numbers and lower/upper case.Select the Country and preferred 3. Language. Then select Next.4.

CProduct RegistrationOpen the envelope that came with the XT4200.1. Locate the serial number and product key.2. On a computer, open a browser and navigate to 3. http://licensing.radvision.com.Complete the online registration form and enter the serial number and product 4. key. The web registration form returns a license key.Write down the license key and keep it in a safe place for future use.5.

B

Graphics and Image Setup If all the sides of the triangles 1 and 2 are visible on your monitor, select next.

Otherwise, press 1 to adjust the 1. position of the top left corner.Use the arrow keys to move 2. the selected triangle until it is fully visible on your monitor. Press OK when done.Press 2 to adjust the position of 3. the bottom right corner.Repeat the procedure using the 4. arrows. Press OK and Next when done.5.

D

SCOPIA XT4200 Quick Setup Guide

Package Content:SCOPIA XT4000 series Codec Unit•

SCOPIA XT XT4200 Camera•

SCOPIA XT 1-way Microphone POD•

SCOPIA XT Remote Control Unit•

Base Camera kit: 2.5m triple camera cable, •including power, VISCA and DVI-D/HDMI

DVI-I to VGA converter•

Cable LAN 4mt•

Cable HDMI M/M, 2.5M•

Power Supply and power cable•

1-way Microphone POD cable•

Remote Control Batteries•

PN 6

2111

-000

11 r

ev A

01

XT4200XT4200

SCOPIA XT4200 Quick Hardware Setup

CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.

Package Content:

Codec Unit

SCOPIA XT4200 Camera

1-way Microphone POD

Remote Control Unit and Batteries

Codec Unit Camera Cable

HDMI Cable

1-way Microphone POD cable

Ethernet Cable for LAN, 4m

Power Supply and Power Cable

DVI-I to VGA converter for PCs with VGA output only

XT4200

XT4200 Camera

Make sure to connect the cable into the IN connector.

4

15

14

8

5

2

Digital or Analog Media Device

Remote Control Batteries

Battery model: CR2025

LITHIUM BATTERY 3V

LITHIUM BATTERY 3V

DC IN 12V IN RS-232C OUT DVIIR SELECT

1 2 3

1 2 3 4 5 6 7 8 9

SYSTEMSELECT

Layouts PiP Inputs Help

SelectMemo

Far Near Presets

9

1

6

7

12

SCOPIA XT4000 series Codec Unit

Please set the system selector on the back of the camera to 7.

16

10 13

11

CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.

3

RADVISION Optional – Not Included Accessories

Audio Cable. Both sockets on the unit are dual purpose. They accept either an analog 3.5mm MiniJack cable or an optical Toslink cable with a Toslink mini-plug adapter. Optical digital audio format is S/PDIF. 1-way microphone POD is connected to the analog/optical input. Analog/optical output can be used for connection to analog or digital media device.

Optional microphone POD

DVI to DVI Cable

Non-RADVISION

HDMI Cable for second monitor

Ethernet Cable for LAN2. Second LAN is optional, and a license key is needed to unlock it.

VGA cable