Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
CC-MC200W ENG 1
Before using the computer, please thoroughly read this manual and keep it for future reference.
Please visit our website, where detailed instruc-tions with movies are available and the instruction manual can be downloaded.
Warning / Caution• Donotconcentrateonthecomputerwhileriding.Ridesafely!• Installthemagnet,sensor,andbracketsecurely.Checktheseperi-odically.
• Ifachildswallowsabattery,consultadoctorimmediately.• Donot leavethecomputer indirectsunlightfora longperiodoftime.
• Donotdisassemblethecomputer.• Donotdropthecomputertoavoidmalfunctionordamage.• Whenusing thecomputer installedon thebracket,change the
MODE bypressingonthefourdotsbelowthescreen,orbypress-ingontheSSEsimultaneously,tostartorstopthetimer.Pressinghardonotherareasmayresult inmalfunctionordamagetothecomputer.
• Besure to tighten thedialof theFlexTight™bracketbyhand.Tightening itstronglyusinga tool,etc.maydamagethescrewthread.
• Whencleaningthecomputer,bracketandsensor,donotusethin-ners,benzene,oralcohol.
• Disposeofusedbatteriesaccordingtolocalregulations.• LCDscreenmaybedistortedwhenviewedthroughpolarizedsun-glasslenses.
Wireless SensorThesensorwasdesignedtoreceivesignalswithinamaximumrangeof70cm,toreducechanceofinterference.Whenadjustingthewire-lesssensor,notethefollowing:• Signalscannotbereceivedifthedistancebetweenthesensorandthecomputer is too large.Thereceivingdistancemaybeshort-enedduetolowtemperatureandexhaustedbatteries.
• Signalscanbereceivedonlywhenthebackof thecomputer isfacingthesensor.
Interferencemayoccur,resultinginincorrectdata,ifthecomputeris:• NearaTV,PC,radio,motor,orinacarortrain.• Closetoarailroadcrossing,railwaytracks,TVstationsand/orra-darbase.
• Usingwithotherwirelessdevicesincloseproximity.
CATEYEMICRO Wireless
CYCLOCOMPUTERCC-MC200W
CC-MC200W ENG 2How to install the unit on your bicycle
SENSOR ZONE
SENSOR ZONE
SENSOR ZONE
SENSOR ZONE
SENSOR ZONE
5 mm
WhenattachingtheFlexTight™brackettothestem
1Attach the bracket to the stem or handlebar
2Install the sensor and magnet
TheFlexTight™bracketcanbeattachedtoeitherthestemorthehandlebar,dependingonhowthebracketfitsintothebracketband.Caution: Be sure to tighten the dial of the FlexTight™ bracket by hand.
Tightening it strongly using a tool, etc. may damage the screw thread.
Remove/Install the computer
Bracketband
Sensor Sensorrubberpad
Nylonties(x2)
Magnet
Bracketband
Bracketband
Handlebar
ClickDial
Cut
Cut
Whilesupportingitbyhand,
Pushitoutas if liftingthefrontup
Stem
Bracket
Bracket
Bracket
Dial Bracketrubberpad
Bracketrubberpad
Bracketrubberpad
Sensorrubberpad
*Installthesensorabovethefrontforkasmuchaspossible.
Speedsensor
Nylonties
Pullsecurely
Magnet
Spoke
Magnet
MagnetSENSOR ZONE
Speedsensor
Speedsensor
Magnet
Speedsensor
SENSOR ZONE
TotheSENSOR ZONE
WhenattachingtheFlexTight™brackettothehandlebarInstall the sensor and magnet
Themagnetpasses through thesensorzoneofthespeedsensor.
Thedistance fromthecom-puter to thesensor iswithinthetransmissiondatalength,andthebackofthecomputerfacesdownward.
Theclearancebetweenthesen-sor surfaceand themagnet iswithin5mm.
Caution:Round off the cut edge of the bracket band to prevent injury.*Tomountthebrackettoanaero-shapedhandlebaror largerstem,usetheoptionalnylonties
bracket.
*Thewheelmagnetmaybeinstalledanywhereonthespokeiftheinstal-lationconditionsaresatisfied.
1
2
CC-MC200W ENG 3
Performtheclearalldataoperationasshownbelow,whenyouusetheunit forthefirsttimeorrestoretheunit totheconditioncheckedatthefactory.
1 Clear all data (initialization)PresstheACbuttononthebackofthecomputer.
2 Select the speed unitsSelect“km/h”or“mph”.
MODE
km/h ↔ mph
MENU
Registerthesetting
3 Enter the tire circumferenceEnter the frontwheel tirecircumferenceofyourbicycleinmm.*Use“Tirecircumferencereference table”asaguide.
MODE
Increasethevalue
MODE
Movedigits(Press&hold) MENU
Registerthesetting
4 Set the clockPressingandholdingtheMODEbuttonswitchesthedisplayto“Displayedtime”,“Hour”,and“Min-ute”inorder.
MODE
12h ↔ 24h (AM↔PMwhen12hisselected),orincreasesthevalue MODE
Switchthescreenormovedigits
5 Press the MENU button to complete setting
MENU
Registerthesetting(Finish)
AC
Operation testAfterinstalled,checkthatthecomputerdisplaysthespeedbyturningthefrontwheel.Whenitisnotdisplayed,checktheinstallationcondi-tions , and again(page2).
Preparing the computer
L mm
ETRTO Tire size L (mm)47-203 12x1.75 93554-203 12x1.95 94040-254 14x1.50 102047-254 14x1.75 105540-305 16x1.50 118547-305 16x1.75 119554-305 16x2.00 124528-349 16x1-1/8 129037-349 16x1-3/8 130032-369 17x1-1/4(369) 134040-355 18x1.50 134047-355 18x1.75 135032-406 20x1.25 145035-406 20x1.35 146040-406 20x1.50 149047-406 20x1.75 151550-406 20x1.95 156528-451 20x1-1/8 154537-451 20x1-3/8 161537-501 22x1-3/8 177040-501 22x1-1/2 178547-507 24x1.75 189050-507 24x2.00 192554-507 24x2.125 196525-520 24x1(520) 1753
24x3/4Tubuler 178528-540 24x1-1/8 179532-540 24x1-1/4 190525-559 26x1(559) 191332-559 26x1.25 195037-559 26x1.40 200540-559 26x1.50 201047-559 26x1.75 202350-559 26x1.95 205054-559 26x2.10 2068
ETRTO Tire size L (mm)57-559 26x2.125 207058-559 26x2.35 208375-559 26x3.00 217028-590 26x1-1/8 197037-590 26x1-3/8 206837-584 26x1-1/2 2100
650CTubuler26x7/8 1920
20-571 650x20C 193823-571 650x23C 1944
25-571 650x25C26x1(571) 1952
40-590 650x38A 212540-584 650x38B 210525-630 27x1(630) 214528-630 27x1-1/8 215532-630 27x1-1/4 216137-630 27x1-3/8 216918-622 700x18C 207019-622 700x19C 208020-622 700x20C 208623-622 700x23C 209625-622 700x25C 210528-622 700x28C 213630-622 700x30C 214632-622 700x32C 2155
700CTubuler 213035-622 700x35C 216838-622 700x38C 218040-622 700x40C 220042-622 700x42C 222444-622 700x44C 223545-622 700x45C 224247-622 700x47C 226854-622 29x2.1 228860-622 29x2.3 2326
SSE
Dotsection
AC
MENU
MODE
Displayformat
Hour Minute
Batterycasecover
Tire circumferenceYoucanfindthetirecircumference(L)ofyourtiresizeinthechartbe-low,oractuallymeasurethetirecircumference(L)ofyourbicycle.• How to measure the tire circumference (L)Forthemostaccuratemeasurement,doawheelrollout.With the tiresunderproperpressure,placethevalvestematthebottom.Markthespoton the floorandwith the rider’sweighton thebike,rollexactlyonewheelrevolution inastraight line(until thevalvecomesaroundagain to thebottom).Markwhere thevalvestemisandmeasurethedistance.
• Tire circumference reference table*Generally,thetiresizeorETRTOisindicatedonthesideofthetire.
Tire size icon
Auto mode icon
CC-MC200W ENG 4Operating the computer [Measuring screen]
Clock display
Elapsed Time0:00’00”–9:59’59”
Stop watch (*2)0:00’00-9:59’59”
Total Distance0–99999km[mile]
Trip Distance0.00–999.99km[mile]
Maximum Speed0.0–105.9km/h[0.0–65.0mph]
Trip Distance-20.00–999.99km[mile]
Average Speed (*1)0.0–105.9km/h[0.0–65.0mph]
Starting / Stopping measurementTherearetwomeasurementmethods;manualmodeandautomode.
Settingmethod
See“Changing thecomputersettings:Selecting theautomode”(Page7).
Thespeedunit(km/hormph)flashesduringmeasurement.*Themaximumspeedandtotaldistanceareupdatedregardlessofstart/stopofthemeasurement.• Auto mode ( illuminated)Measurementsstartautomaticallywhenthebicycleisinmotion.
START STOP
• Manual modePresstheSSEbuttontogetherwiththeunit tostart/stopthemeasurement.
SSE+MODE
Starting/Stoppingmeasurement
*Whenthecomputer isremovedfromthebracket,press theSSEbuttononthefrontandtheMODEbuttononthebacksimultane-ously.
Resetting dataPressingandholdingSSE togetherwith theuniton themeasurementscreenresetsanymeasurementdata,ex-cept thetotaldistance(Odo), tripdistance-2(Dst2),andstopwatch( ).*Thetotaldistance(ODO)isnotreset.
• Resetting separately the trip distance-2 and stop watchToresetthecurrentlydisplayeddata,displaytripdistance2(Dst2)orthestopwatch( ),andholddownthemainunitalongwiththeSSE.*How to reset the trip distance 2 (Dst2) and the
stopwatch displayed in top row of screenDisplaythecurrentspeed(Spd)inbottomrowofscreenandperformtheresetoperation.
Switching computer functionPressingtheMODEbuttonswitchesthemeasurementdataatthebottomintheordershowninthefollowingfigure.
Current speed0.0( :4.0/ :3.0)–105.9km/h[0.0( :3.0/ :2.0)–65.0mph]*“Spd”iconisdisplayedwhendisplay-ingcurrentspeedatthebottom.
Sensor signal iconFlashesinsynchwithasensorsignal.
Pace arrow Indicateswhether thecurrentspeedis faster ( )orslower ( ) than theaveragespeed.
Speed unit
*1 WhenTmabout10hours,orDstexceeds999.99km,.Ewillappear.Resetthedata.
*2 Itappearsonlyintheautomode.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
Click
Click
MODE operation when the computer is mount-
ed on the bracket
SSE+MODE
SSE
ON
OFF
SSE+MODE(Press&hold)
CC-MC200W ENG 5Operating the computer [Various functions]
Setting the function to displayDisplayingonlyselecteddatacanbedone.
Tm Dst Dst2 Av
MxOdo
Tm Dst Av
Mx
Settingmethod
See“Changingthecomputersettings:Settingthefunction”(Page7).
*Thecurrentspeed(Spd),andtheelapsedtime(Tm)cannotbehidden.*Whenyouhidethefunctionassignedtothetopdisplay,theupperdis-playreturnstothecurrentspeed(Spd).
*Theunitkeepsrecordinghiddendataonbackgroundandeachmea-surementdataisupdatedwhendisplayed(exceptforthestopwatch).
Stop watch Thetimecanbemeasuredregardlessofstart/stopofthemeasurement.Itcanbeusedwhentheautomodeison( illuminated).• Start/Stop: PresstheSSEbuttontogetherwiththeunit. flashes
duringmeasurement.• Reset: Displaythestopwatch( ),andholddownthemain
unitalongwiththeSSEbutton.*How to reset the trip distance 2 (Dst2) and the stop-
watch displayed in top row of screenDisplaythecurrentspeed(Spd)inbottomrowofscreenandperformtheresetoperation.
=
MODE
Upper display selectionAnydatacanbeselectedforthetopdisplay,andconstantlybedisplayed.
TmTm
SpdSpd TmTm
SpdSpd
Settingmethod
See“Changingthecomputersettings:Settingtheupperdis-play”(Page6).
*Thestopwatchcannotbesetwhentheauto-modeisoff.
Power-saving functionIf thecomputerhasnotreceivedasignal for10minutes,power-savingscreenwillactivateandonlytheclockwillbedisplayed.WhenyoupressMODE,or thecomputerreceivesasensorsignal, themeasuringscreenreappears.
*Ifanother12hoursof inactivityelapses in thepower-savingscreen,only thespeedunit isdisplayedon thescreen.Withsuchascreen,pressingtheMODEbuttonreturnstothemeasurementscreen.
SSE+MODE
Starting/Stoppingmeasurement
Power-saving screen
Sleep
10minutes
12hours
MODE
Backlight (Night mode )Withthenightmodeturnedon,pressingtheMODEbuttonturnsonthebacklight(for5seconds).Pressinganybuttonwhilethebacklightisstillonextendstheilluminationforanother5seconds.
Settingmethod
PressingandholdingtheMODEbuttonproceedstosettingthenightmode.Pressingandholdingthebuttonagainturnsonthenightmode,andreturnstothemeasurementscreen.
*Thenightmodeisautomaticallyturnedoffwithoutanysignalreceivedfor10minutes.
*YoucanswitchON/OFFalsofromthemenuscreen.See“Changingthecomputersettings:Settingthenightmode”(Page6).
*When (batteryicon)isturnedon,thebacklightisnotturnedonevenifthenightmodeison.
ON
MODE
OFF
Measuringscreen
Selectingthenightmodescreen
ON
ON
MODE(Press&hold)
Measuring screen
MENU
MENU
MODE
MODE
MODE
MODE
MODE
Selecting the night mode
Switching the circumference
Setting the upper display
Selecting the auto mode
Setting the tire circumference
Setting the function
Setting the clock
Entering the total distance
MODE
MODE
MODE
MODE
MODE
MODE
Selecting the night modeSelectON/OFFofthenightmode.*PressingandholdingtheMODEbuttonshortcuts tothisscreenfromthemeasurementscreen.
Switching the circumference ( )Switch and ofthetirecircumferencecurrentlyselected.*Thecircumference issetona low-speedorientedbasis; therefore, it issuitableforMTB.
MODE
A ↔ B
MODE
MODE
MENU
Selecting the measurement unit
Changing the settings
Changing the settings
Changing the settings
(Press&hold)
(Press&hold)
(Press&hold)
Register the setting
CC-MC200W ENG 6Changing the computer settings [Menu screen]
PressingMENUonthemeasurementscreenchangestothemenuscreen.Varioussettingscanbechangedonthemenuscreen.*Afterchangesaremade,besuretoregisterthesetting(s)bypressingtheMENUbutton.*Leavingthemenuscreenwithoutanyoperationfor1minutesreturnstothemeasurementscreen,andchang-esarenotsaved.
MODE
Setting the upper displaySelectthefunctionfortheupperdisplay.
MODE
To“Settingthetirecircumference”
From“Selectingthemeasurementunit”
Spd
Tm Dst Dst2 Av
Odo MxMODE
MODE
ON ↔ OFF
MENU
MENU
Register the setting
Register the setting
Changing the settings Changing the settings
Changing the settings
Changing the settings
(Press&hold) (Press&hold)
(Press&hold)
(Press&hold)
(Press&hold)
(Press&hold)
(Press&hold)(Press&hold)
CC-MC200W ENG 7Changing the computer settings [Menu screen]
Setting the clockSettheclock.
Setting the functionSelectthefunctiontobehidden.
Selecting the auto modeSelectON/OFFoftheautomode.
MODE
MODE
MODEMODE
MODE
12h ↔ 24h
12h24h MODE
AM ↔ PM
MODE
ON ↔ OFF
MODE
MODE
MODE
MODE
MODE
MODE
MODE
To“Enteringthetotaldistance”To“Settingthefunction”
From“Switchingthecircumference” From“Settingtheclock”
0–23[1–12]
Hour Minute
00–59
MODE
Setting the tire circumferenceEnterthetirecircumference.
MODE MODE
MODEMODE
ON ↔ OFF
0100–3999
Av → Mx → Odo
Dst
MODE MODE
Increasethevalue
Increasethevalue
Movedigits(press&hold)
Switchthescreen(press&hold)
(Press&hold)
MENU
MENU
Register the setting
Register the setting
MENU
MENU
Register the setting
Register the setting
Entering the total distanceEnterthetotaldistance.*Onceyouenteranyvaluetothetotaldistance,youcanstartfromthevalueyouentered.Usethisfunctionwhenyourenewand/orresetyourunit.
Selecting the measurement unitSelectthespeedunit(km/hormph).
MODE
MODE km/h ↔ mph
MODE
MODE
MODE
To“Selectingthenightmode”
From“Selectingtheautomode”
Changing the settings
Changing the settings
(Press&hold)
(Press&hold)
MENU
MENU
Register the setting
Register the setting
CC-MC200W ENG 8Changing the computer settings [Menu screen]
MODE
MODE
00000–99999Movedigits(press&hold)
Increasethevalue
CC-MC200W ENG 9In use
MaintenanceTocleanthecomputeroraccessories,usedilutedneutraldetergentonasoftcloth,andwipeitoffwithadrycloth.
Replacing the batteryComputerWhen (batteryicon)isturnedon,replacethebattery.Installanewlithiumbattery(CR2032)withthe(+)sidefacingupward.*Afterreplacingthecomputerbattery,followtheproceduredescribed in“Preparingthecomputer”(Page3).
SensorWhenthespeedisnotdisplayedevenaf-teradjustingcorrectly,replacethebattery.
Insertnewlithiumbatteries(CR2032)withthe(+)signupward,andclosethebatterycoverfirmly.*Afterreplacement,checkthepositionsofthesensorandmagnet.
COIN
CR2032
COIN
CR2032
TroubleshootingThe sensor signal icon does not flash (the speed is not displayed). (Movethecomputernearthesensor,andturnthefrontwheel.Ifthesensorsignal iconflashes, thistroublemaybeamatterof transmissiondistanceduetobatterydrain,butnotanymalfunction.)
Checkthattheclearancebetweenthesensorandmagnetisnottoolarge.(Clearance:within5mm)
Checkthatthemagnetpassesthroughthesensorzonecorrectly.
Adjustthepositionsofthemagnetandsensor.
Isthecomputerinstalledatthecorrectangle?
Backofcomputermustfacetowardthesensor.
Checkthatthedistancebetweenthecomputerandsensoriscorrect.(Distance:within20to70cm)
Installthesensorwithinthespecifiedrange.
Isthecomputerorsensorbatteryweak?Inwinter,batteryperformancediminishes.
Replacewithnewbatteriesaccordingtotheprocedurespeci-fiedinthesection“Replacingthebattery”.
Nothing is displayed by pressing the button.
Replace thecomputerbatteryaccording to theprocedurespecifiedinthesection“Replacingthebattery”.
Incorrect data appear.
Clearallaccordingtotheproceduredescribed in“Preparingthecomputer”(Page3).
The backlight is not turned on.
Checkif (batteryicon)isturnedon.
Replace thecomputerbatteryaccording to theprocedurespecifiedinthesection“Replacingthebattery”.
Close
Close
Open
Open
Specification
Battery/Batterylife
Computer: Lithiumbattery(CR2032)x1/Approx.1years(Ifthecomputerisusedfor1hour/day;thebatterylifewillvarydependingontheconditionsofuse.)
Sensor: Lithiumbattery(CR2032)x1/UnitTotalDistancereachesabout10000km(6250mile)
* Itmaybeshortenedsignificantlywhenbacklightisusedfrequently.* Thisistheaveragefigureofbeingusedunder20°Ctemperatureandthedistancebetweenthecom-puterandthesensoris65cm.
* Thefactory-loadedbatterylifemightbeshorterthantheabove-mentionedspecification.Controller 4bit,1-chipmicrocomputer(Crystalcontrolledoscillator)Display LiquidcrystaldisplaySensor NocontactmagneticsensorTransmissiondistance Between20and70cm
Tirecircumferencerange
0100mm-3999mm(Initialvalue:A=2096mm,B=2050mm)
Workingtemperature
0°F-104°F(0°C-40°C)(ThisproductwillnotdisplayappropriatelywhenexceedingtheWorkingTemperaturerange.SlowresponseorblackLCDatlowerorhighertemperaturemayhappenrespectively.)
Dimensions/weight
Computer: 2-7/64”x1-27/64”x11/16”(53.5x36x17.5mm)/0.92oz(26g)
Sensor: 1-41/64”x1-27/64”x19/32”(41.5x36x15mm)/0.53oz(15g)
* Thespecificationsanddesignaresubjecttochangewithoutnotice.
Limited warranty2-Year Computer/Sensor only(Accessories and Battery Consumption excluded)CatEyecyclecomputersarewarrantedtobefreeofdefectsfrommaterialsandworkmanshipforaperiodoftwoyearsfromoriginalpurchase.Iftheproductfailstoworkduetonormaluse,CatEyewillrepairorreplacethedefectatnocharge.ServicemustbeperformedbyCatEyeoranauthorizedretailer.Toreturntheproduct,packitcarefullyandenclosethewarrantycertificate(proofofpurchase)with instructionforrepair.Pleasewriteortypeyournameandaddressclearlyonthewarrantycertificate. Insurance,handlingandtransportationchargestoCatEyeshallbebornebypersondesiringservice.ForUKandREPUBLICOFIRELANDconsumers,pleasereturntotheplaceofpurchase.Thisdoesnotaffectyourstatutoryrights.
2-8-25,Kuwazu,HigashiSumiyoshi-ku,Osaka546-0041JapanAttn:CATEYECustomerServiceSectionPhone :(06)6719-6863 Fax :(06)6719-6033E-mail :[email protected] URL :http://www.cateye.com
[For US Customers]CATEYE AMERICA, INC.2825WildernessPlaceSuite1200,BoulderCO80301-5494USAPhone :303.443.4595 TollFree :800.5CATEYEFax :303.473.0006 E-mail :[email protected]
1600280N 16021931602196 16029801602190 1665150
CR2032
1699691N
Partskit Wheelmagnet NylontiebracketLithiumbatterySpeedsensor Bracketband Bracket
Spare accessoriesStandard accessories Optional accessories