Upload
andrei-kolozsvari
View
316
Download
3
Embed Size (px)
Citation preview
7/21/2019 catalog Megaprofil 2013 (1).pdf
1/191
ECHNICAL CAALOGUE2013
VERSION 1.1
7/21/2019 catalog Megaprofil 2013 (1).pdf
2/1912
THE NETHE RLANDS
MEGAPROFIL
DIVISIONS
MEGAPROFIL
HeadquartersStr. Principal nr. 58, Buziajud. TimiTel: 0256 307 700
Fax: F: 0256 307 729Email: [email protected]
www.megaprofil.ro
7/21/2019 catalog Megaprofil 2013 (1).pdf
3/1913
ECHNICAL CAALOGUE2013
MEGAPROFIL is a famous manufacturer of steel panels for wallsand roofs, adequate mainly for new constructions and restorationworks in the agricultural sector, do-it-yourself sector, for construc-tions of roofs and private housings.
The quality of our products is guaranteed by our experience in thefield. Consequently, we use only high quality steel, galvanized andcovered with protection coatings, to ensure a longer operationallife.
Our experienced staff provides customized solutions, according toyour requirements. Thus, we make available for you a wide range
of profiles for walls and roofs, sandwich panels, roof tile panels,Perma tile, galvanized profiles, as well as sliding door tracks andaccessories.
In order to guarantee a fast delivery, we can provide a wide rangeof products available from stock, with standard lengths and co-lours (see the indications in red).
All metal profiles, sandwich panels and panels imitating tiles maybe ordered directly in various colours and sizes, according to yourneeds.
The order shall be delivered directly to your address.
The Sales Department shall always provide you with the technicalinformation you need and they shall advise you for the selectionof the correct product.
7/21/2019 catalog Megaprofil 2013 (1).pdf
4/1914
CONTENTS
Megaprofil is not claiming responsibility for the printing mistakes
and they reserve the right to modify at any moment the technicalspecifications of their products, without previous notice.
MRRO011-0
1.W
ALLSANDROOFPROFILES
8.116,5.1180
16,5.137,5.1100
35.207.1035
38.250.1000
45.333.1000
76.18.988 (SINUS)
OPTIC PROFILE
PLANK PROFILE
1-1
1-4
1-7
1-10
1-13
1-16
1-18
1-19
2.T
ECHNICALPROFILES
DECK 115.600
DECK 125.600
DECK 160.600
85.280.1120
135.310.930
153.280.840
158.250.750
200.420.750
58.210.840
POLYURETHANE ROOF
POLYURETHANE WALL
MINERAL WOOL
ROOF PANEL MINERAL
WOOL
WALL PANEL MINERAL
WOOL
ECOPANEL
ACOUSTIC PANELS
POLYURETHANE RIGID
PLATE
FOR POLYURETHANE
ROOF
2-1
2-3
2-5
2-7
2-10
2-13
2-16
2-19
2-22
3-1
3-5
3-9
3-10
3-13
3-16
3-18
3-20
3-21
4.
ROOFTILEPANELS
3.
INSULATEDPANELS
INFORMATION REGARDING
ROOF TILE PANELS
MEGA ROYAL
MEGA CLASSIC
MEGA RUSTICA
PERMA
4-1
4-3
4-4
4-5
4-6
7/21/2019 catalog Megaprofil 2013 (1).pdf
5/1915
DIVISIONS 3
GENERAL PRESENTATION OF ROOFING LAYERS 6COLOUR PALETTE 10
5.
GALVANIZEDPROFILES
Z PURLIN
MANUFACTURED BY MEGAPROFIL
Z PURLIN
MANUFACTURED BY JORIS IDE NV
Z PURLIN
INFORMATION
Z STRUCTURES
PURLIN
PURLIN
INFORMATION
FIXATION PROFILE
30/30/30-1.5
PROFILE
BOTTLE AND HALF BOTTLE-LIKE
PROFILES
C PROFILES
DRYWALL PROFILES
5-1
5-3
5-5
5-24
5-32
5-33
5-38
5-39
5-40
5-41
5-43
6.
ACCESSORIES
WALL AND ROOF PROFILES
FINISHING PROFILES
APPLICATIONS
FILLING STRIPS
ROOF-TILE LIGHT PANELS
FIXATION MATERIALS
PIPE FEED-THROUGH PARTS
FOR INSULATED PANELS
PVC FINISHING PROFILES
PVC ROOF LIGHTS
FILLING STRIPS
FOR ROOF TILE PANELS
FINISHING PARTS
GUTTERS
POLYESTER GUTTERS
PVC GUTTERS
6-1
6-2
6-3
6-4
6-5
6-7
6-8
6-10
6-11
6-12
6-13
6-15
8.
FINISHINGPROFILE
PROFILED ROOF SHEET
PROFILED WALL SHEET
SANDWICH PANELS
FOR ROOF
SANDWICH PANELS
FOR WALL
ROOF TILE PLATES
ROOF TILE PLATES
WITH INSULATION, PERMAPAN
8-1
8-8
8-15
8-22
8-27
8-33
7.
APPLICATIONSANDASSEMB
LY
HANDLING INSTRUCTIONS
MOUNTING OF PROFILES
MOUNTING
OF INSULATING PANELS
MOUNTING
OF ROOF TILE PANELS
7-1
7-3
7-6
7-7
7/21/2019 catalog Megaprofil 2013 (1).pdf
6/1916
INDICAORS FOR HE SELECION OF PRE-PAINED SEEL
Application on the
outside
Raw materialSteel quality: S280GD, S250GD, according to EN10147Standard Sendzimir galvanization: Z225 or 225 g zinc per m2of plate (painted HPS200ULTRA and PRISMA ZA265) or 265 g/m2(95%zinc + 5% aluminium), which provides additional resistance to corrosion.
The applications and advantages depend of the type and thickness of the painted surface (coating) on the outer side. The inner side isprovided with a standard layer (primer) of 15 , painted with the RAL 9002 colour.
Interior aggressive
environmentStable
construction
Sandwich panelwith inner side:
COLORFARMR BP
PLATISOL 300
Sandwich panel
with inner side:
FOOD SAFE
POLYURETHANE 50
HPS200R ULTRA
POLYESTER 35
POLYURETHANE 50
HPS200R ULTRA
Food industry
Architectural
colors
POLYESTER 35
POLYURETHANE
50
High UV resistance
Oceanic environment
and heavy industry
Resistant to chemical
substances
Specific requirements of
strength and resistance
to mud
Oceanic environment
and heavy industry
POLYESTER
25
PVDF
25
Polyester
15
NO NO NO NO
NO NO
NO
NO
NO
PLATISOL
200
PRODUC INDICAORS FOR PRE-PAINED SEEL
GENERAL PRESENAION
YES
YES YES
YES YES
YES
YES
YES YES
YES
7/21/2019 catalog Megaprofil 2013 (1).pdf
7/1917
SANDARD RANGE OF PRODUCS FOR PRE-PAINED SEEL
Polyester 15 (PE15) =15 microns of polyester
Upper layer
Pre-treatment
Zinc Z100
Steel
Zinc Z100
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc Z225
Steel
Zinc Z225
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc Z225
Steel
Zinc Z225
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc ZA265
Steel
Zinc ZA265
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc ZA265
Steel
Zinc ZA265
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc Z225
Steel
Zinc Z225
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc Z225
Steel
Zinc Z225
Pre-treatment
Lower layer
Upper layer
Primer
Pre-treatment
Zinc Z225
Steel
Zinc Z225
Pre-treatment
Lower layer
Polyvinylidene difluoride 25 (PVDF25) =5 primer + 20 topcoat PVDF
Plastisol 200 (PS200) = primer + 200 PVC layer +longitudinal engraving or with leather pattern
Polyurethane 55 (PUR50) = primer + 200 PVC layer +scintilla engraving
TURBID (PE25) =primer + 200 PVC layer + turbid lacquer
Note: - Reduced adherence due to less profound engraving than in the case of longitudinal or leather pattern one - Excellent resistance: CONFIDEX warranty of up to 40 years (upon request, together with the order)
Note: - Excellent resistance: CONFIDEX warranty of up to 25 years (upon request, together with the order)
Polyurethane 35 (PUR35) =15 primer + 20 polyurethane
HPS200 ULRA (PS200H) = primer + 200 PVClayer + scintilla engraving
Polyester 25 (PE25) =5 primer + 20 polyester
COATINGS
SANDARD RANGE OF PRODUCS
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
8/1918
SPECIAL INERIOR PLAE FOR SANDWICH PANELS
SANDARD RANGE OF PRODUCS
COATINGS
Agricultural sector:
Upper layer
Primer
Pre-treatment
Zinc ZA265
Steel
Zinc ZA265
Pre-treatment
Lower layerAdvantages:Very good resistance against corrosionand humidity, good resistance to
many chemicals occurring in stables
Advantages:Good resistance against corrosion andhumidity, good resistance to manychemicals occurring in stables
Upper layer
Primer
Pre-treatment
Zinc ZA265
Steel
Zinc ZA265
Pre-treatment
Lower layer
COLORFARM BP (CF35) = high quality primer + 30 flexible copolymer
PLASTISOL 300 (PS300)= standard primer + 300 fine plastisol
Food industry
Foodsafe manual according to NF P75-401-1
Ai1Non-aggressive
environmentPeriodic
maintenanceLow air humidity
Btw -40C and+25C
PE15 orPE25
*
Storage of dry packaging or frozen prod-ucts (except for bulk fish), sorting andpackaging areas
Ai2Non-aggressive
environmentPeriodic
maintenanceMedium air
humidityBtw 0C and
+25CPE15PE25
Storage (fruit and vegetables) in controlledenvironments, preservation of dairies
Ai3Non-aggressive
environmentLess intensive
cleaningHigh air humidity
Btw 0Cand+25C
PURE 35**
Storage and processing in moist environ-ments (salads, flowers, fruit). Production ofice frozen meat
Ai4
Environmentwith minimum
level ofaggression
Less intensivecleaning
MoistBtw 0C and
+25oCWine cellars, butcheries, sausagesprocessing, butter processing
Ai5Aggressive
environmentIntensivecleaning
Very moistBtw 0C and
+35CPVC 150
***Mushrooms farms, halls for cheese, storageand freezing of bulk fish
Ai6Very aggressive
environmentVery intensive
cleaningSaturated
Btw 0C and+40oC
Entrails, sorting, brining, dairy products orcheese factories, sea fruit
* RAL 9001, RAL 9002, RAL 9010
** RAL 9002, RAL 9010
*** PVC LAMINATED FILMS 150M: RAL 9001, RAL 9002, RAL 9010
7/21/2019 catalog Megaprofil 2013 (1).pdf
9/1919
ECHNICAL SPECIFICAIONS
TECHNICALSPECIFICATIONS
PE15 PE25 PVDF25 PUR35 PS200HPS200ULTRA
PUR50 TURBID
Ductility 3T 3T 2T 2T 3T 1.5T 1.5T 1T
Resistance to corrosion(salt fog testing)
150hours
360hours
500hours
500hours
700hours
1000hours
700hours
360hours
Resistance to UV RUV2 RUV4 RUV4 RUV2 RUV4 RUV4 RUV4
Classification for fireCSTB NF EN 13501-1
MOA1
MOA1
MOA1
MOA1-2
A1
Hardness/resistance toscratching
HB-H HB-H HB-H HB-H 4-6B 4-6B F-H F
Resistance to acids andbases
GoodVerygood
Good Good Good Good Good
Resistance to chemicals GoodExcel-lent
Good Good Good Good Good
COATINGS
PROPERIES
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
10/19110
COLOUR CHAR
MEGAPROFIL
RAL 1015 RAL 3000 RAL 3005 RAL 3011 RAL 5005
RAL 5008
RAL 6021
RAL 8017
RAL 9007 RAL 9010
RAL 9001 RAL 9002 RAL 9005 RAL 9006
RAL 5010
RAL 9001
RAL 6003
RAL 9002
RAL 6005
RAL 9005
RAL 6011
RAL 9006
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
11/1911-1
ROOF AND WALLS PROFILES
8.116,5.1180
APPLICAION
Wall
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.25| 0.40 | 0.50 | 0.60
Polyester-silicone 25 14 standard colours thickness 0.40| 0.45 | 0.50 | 0.60 | 0.75 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMODULE W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.35 15.00 15.00 0.38 0.66 75.60
0.45 3.76 17.90 17.90 0.45 0.79 93.40
0.50 4.17 22.00 22.00 0.54 0.97 112.70
0.60 4.59 31.80 31.80 0.74 1.40 155.90
0.75 6.24 46.80 46.80 1.05 2.06 231.50
7/21/2019 catalog Megaprofil 2013 (1).pdf
12/1911-2
8.116,5.1180
ROOF AND WALLS PROFILES
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 3.78 3.02 2.52 2.16 1.88 1.48 1.20 0.99 0.83 0.71 0.61 0.53 0.47 0.42 0.37 0.33 0.30
L/150 3.78 3.02 1.89 1.19 0.80 0.56 0.41 0.31 0.24 0.19 0.15 0.12 0.10 0.08 0.07 0.06 0.05
L/200 3.78 2.45 1.42 0.89 0.60 0.42 0.31 0.23 0.18 0.14 0.11 0.09 0.07 0.06 0.05 0.04 0.04
L/250 3.78 1.96 1.13 0.71 0.48 0.34 0.25 0.18 0.14 0.11 0.09 0.07 0.06 0.05 0.04 0.04 0.03
0.45
SLU 4.67 3.74 3.11 2.67 2.24 1.77 1.43 1.18 0.99 0.85 0.73 0.64 0.56 0.50 0.44 0.40 0.36
L/150 4.67 3.74 2.24 1.41 0.95 0.66 0.48 0.36 0.28 0.22 0.18 0.14 0.12 0.10 0.08 0.07 0.06
L/200 4.67 2.90 1.68 1.06 0.71 0.50 0.36 0.27 0.21 0.17 0.13 0.11 0.09 0.07 0.06 0.05 0.05
L/250 4.54 2.32 1.34 0.85 0.57 0.40 0.29 0.22 0.17 0.13 0.11 0.09 0.07 0.06 0.05 0.04 0.04
0.50
SLU 5.64 4.51 3.76 3.22 2.75 2.17 1.76 1.45 1.22 1.04 0.90 0.78 0.69 0.61 0.54 0.49 0.44
L/150 5.64 4.51 2.69 1.69 1.13 0.80 0.58 0.44 0.34 0.26 0.21 0.17 0.14 0.12 0.10 0.08 0.07
L/200 5.64 3.48 2.02 1.27 0.85 0.60 0.44 0.33 0.25 0.20 0.16 0.13 0.11 0.09 0.07 0.06 0.05
L/250 5.44 2.79 1.61 1.02 0.68 0.48 0.35 0.26 0.20 0.16 0.13 0.10 0.09 0.07 0.06 0.05 0.04
0.60
SLU 7.80 6.24 5.20 4.45 3.90 3.14 2.54 2.10 1.77 1.51 1.30 1.13 0.99 0.88 0.79 0.70 0.64
L/150 7.80 6.24 3.68 2.32 1.55 1.09 0.80 0.60 0.46 0.36 0.29 0.24 0.19 0.16 0.14 0.12 0.10
L/200 7.80 4.77 2.76 1.74 1.17 0.82 0.60 0.45 0.35 0.27 0.22 0.18 0.15 0.12 0.10 0.09 0.07
L/250 7.46 3.82 2.21 1.39 0.93 0.65 0.48 0.36 0.28 0.22 0.17 0.14 0.12 0.10 0.08 0.07 0.06
0.75
SLU 11.58 9.26 7.72 6.61 5.79 4.62 3.74 3.09 2.60 2.22 1.91 1.66 1.46 1.30 1.16 1.04 0.94
L/150 11.58 9.03 5.23 3.29 2.21 1.55 1.13 0.85 0.65 0.51 0.41 0.33 0.28 0.23 0.19 0.16 0.14
L/200 11.58 6.77 3.92 2.47 1.65 1.16 0.85 0.64 0.49 0.39 0.31 0.25 0.21 0.17 0.15 0.12 0.11
L/250 10.58 5.42 3.14 1.97 1.32 0.93 0.68 0.51 0.39 0.31 0.25 0.20 0.17 0.14 0.12 0.10 0.08
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 1.42 1.13 0.92 0.76 0.64 0.55 0.48 0.42 0.38 0.34 0.30 0.28 0.25 0.23 0.21 0.20 0.18
L/150 1.42 1.13 0.92 0.76 0.64 0.55 0.48 0.42 0.38 0.34 0.30 0.28 0.24 0.20 0.17 0.15 0.12
L/200 1.42 1.13 0.92 0.76 0.64 0.55 0.48 0.42 0.38 0.34 0.27 0.22 0.18 0.15 0.13 0.11 0.09
L/250 1.42 1.13 0.92 0.76 0.64 0.55 0.48 0.42 0.35 0.27 0.22 0.18 0.15 0.12 0.10 0.09 0.07
0.45
SLU 1.75 1.40 1.13 0.93 0.79 0.68 0.59 0.52 0.46 0.41 0.37 0.34 0.31 0.28 0.26 0.24 0.22
L/150 1.75 1.40 1.13 0.93 0.79 0.68 0.59 0.52 0.46 0.41 0.37 0.34 0.29 0.24 0.20 0.17 0.15
L/200 1.75 1.40 1.13 0.93 0.79 0.68 0.59 0.52 0.46 0.40 0.32 0.26 0.22 0.18 0.15 0.13 0.11
L/250 1.75 1.40 1.13 0.93 0.79 0.68 0.59 0.52 0.41 0.32 0.26 0.21 0.17 0.14 0.12 0.10 0.09
0.50
SLU 2.11 1.69 1.37 1.13 0.95 0.82 0.71 0.63 0.56 0.50 0.45 0.41 0.37 0.34 0.31 0.29 0.27
L/150 2.11 1.69 1.37 1.13 0.95 0.82 0.71 0.63 0.56 0.50 0.45 0.41 0.35 0.29 0.24 0.21 0.18
L/200 2.11 1.69 1.37 1.13 0.95 0.82 0.71 0.63 0.56 0.48 0.39 0.31 0.26 0.22 0.18 0.15 0.13
L/250 2.11 1.69 1.37 1.13 0.95 0.82 0.71 0.63 0.49 0.39 0.31 0.25 0.21 0.17 0.15 0.12 0.11
0.60
SLU 2.92 2.34 1.91 1.58 1.34 1.15 1.00 0.88 0.79 0.70 0.64 0.58 0.53 0.48 0.44 0.41 0.38
L/150 2.92 2.34 1.91 1.58 1.34 1.15 1.00 0.88 0.79 0.70 0.64 0.57 0.47 0.39 0.33 0.28 0.24
L/200 2.92 2.34 1.91 1.58 1.34 1.15 1.00 0.88 0.79 0.66 0.53 0.43 0.36 0.30 0.25 0.21 0.18
L/250 2.92 2.34 1.91 1.58 1.34 1.15 1.00 0.87 0.67 0.53 0.42 0.34 0.28 0.24 0.20 0.17 0.15
0.75
SLU 4.34 3.47 2.83 2.34 1.98 1.70 1.48 1.31 1.16 1.04 0.94 0.85 0.78 0.71 0.66 0.61 0.56
L/150 4.34 3.47 2.83 2.34 1.98 1.70 1.48 1.31 1.16 1.04 0.94 0.82 0.67 0.56 0.47 0.40 0.34
L/200 4.34 3.47 2.83 2.34 1.98 1.70 1.48 1.31 1.16 0.94 0.75 0.61 0.50 0.42 0.35 0.30 0.26
L/250 4.34 3.47 2.83 2.34 1.98 1.70 1.48 1.24 0.96 0.75 0.60 0.49 0.40 0.34 0.28 0.24 0.21
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
13/1911-3
ROOF AND WALLS PROFILES
8.116,5.1180
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 1.65 1.32 1.09 0.90 0.76 0.66 0.57 0.51 0.45 0.40 0.37 0.33 0.30 0.28 0.26 0.24 0.22
L/150 1.65 1.32 1.09 0.90 0.76 0.66 0.57 0.51 0.45 0.36 0.29 0.23 0.19 0.16 0.13 0.11 0.10
L/200 1.65 1.32 1.09 0.90 0.76 0.66 0.57 0.44 0.34 0.27 0.21 0.17 0.14 0.12 0.10 0.09 0.07
L/250 1.65 1.32 1.09 0.90 0.76 0.65 0.47 0.35 0.27 0.21 0.17 0.14 0.12 0.10 0.08 0.07 0.06
0.45
SLU 2.04 1.63 1.34 1.11 0.94 0.80 0.70 0.62 0.55 0.49 0.45 0.40 0.37 0.34 0.31 0.29 0.27
L/150 2.04 1.63 1.34 1.11 0.94 0.80 0.70 0.62 0.54 0.42 0.34 0.28 0.23 0.19 0.16 0.14 0.12
L/200 2.04 1.63 1.34 1.11 0.94 0.80 0.70 0.52 0.40 0.32 0.25 0.21 0.17 0.14 0.12 0.10 0.09
L/250 2.04 1.63 1.34 1.11 0.94 0.77 0.56 0.42 0.32 0.25 0.20 0.17 0.14 0.11 0.10 0.08 0.07
0.50
SLU 2.47 1.97 1.62 1.34 1.13 0.98 0.85 0.75 0.67 0.60 0.54 0.49 0.45 0.41 0.38 0.35 0.32
L/150 2.47 1.97 1.62 1.34 1.13 0.98 0.85 0.75 0.65 0.51 0.41 0.33 0.27 0.23 0.19 0.16 0.14
L/200 2.47 1.97 1.62 1.34 1.13 0.98 0.84 0.63 0.48 0.38 0.31 0.25 0.20 0.17 0.14 0.12 0.10
L/250 2.47 1.97 1.62 1.34 1.13 0.92 0.67 0.50 0.39 0.30 0.24 0.20 0.16 0.14 0.11 0.10 0.08
0.60
SLU 3.41 2.73 2.26 1.87 1.59 1.37 1.19 1.05 0.94 0.84 0.76 0.69 0.63 0.58 0.53 0.49 0.46
L/150 3.41 2.73 2.26 1.87 1.59 1.37 1.19 1.05 0.89 0.70 0.56 0.45 0.37 0.31 0.26 0.22 0.19
L/200 3.41 2.73 2.26 1.87 1.59 1.37 1.15 0.86 0.66 0.52 0.42 0.34 0.28 0.23 0.20 0.17 0.14
L/250 3.41 2.73 2.26 1.87 1.59 1.26 0.92 0.69 0.53 0.42 0.33 0.27 0.22 0.19 0.16 0.13 0.11
0.75
SLU 5.06 4.05 3.35 2.78 2.35 2.02 1.77 1.56 1.39 1.25 1.13 1.02 0.94 0.86 0.79 0.73 0.68
L/150 5.06 4.05 3.35 2.78 2.35 2.02 1.77 1.56 1.26 0.99 0.79 0.64 0.53 0.44 0.37 0.32 0.27
L/200 5.06 4.05 3.35 2.78 2.35 2.02 1.63 1.22 0.94 0.74 0.59 0.48 0.40 0.33 0.28 0.24 0.20
L/250 5.06 4.05 3.35 2.78 2.35 1.79 1.30 0.98 0.75 0.59 0.47 0.39 0.32 0.27 0.22 0.19 0.16
ables containing loads determined according to EC3-1-3-2001Te calculation load for SLU must include thesafety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
7/21/2019 catalog Megaprofil 2013 (1).pdf
14/1911-4
16.5.137,5.1100
ROOF
WALL
ROOF AND WALLS PROFILES
APPLICAION
Roof, wall
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.25| 0.40 | 0.50 | 0.60
Polyester-silicone 25 14 standard colours thickness 0.40| 0.45 | 0.50 | 0.60
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.58 28.90 28.90 1.54 1.23 653.00
0.45 4.04 33.60 33.60 1.85 1.48 886.00
0.50 4.48 42.80 42.80 2.14 1.72 1119.00
0.60 4.93 63.00 63.00 2.72 2.17 1430.00
7/21/2019 catalog Megaprofil 2013 (1).pdf
15/1911-5
ROOF AND WALLS PROFILES
16.5.137,5.1100
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 14.50 9.28 6.44 4.73 3.63 2.86 2.32 1.92 1.61 1.37 1.18 1.03 0.91 0.80 0.72 0.64 0.58
L/150 14.50 9.28 6.44 4.73 3.23 2.27 1.66 1.24 0.96 0.75 0.60 0.49 0.40 0.34 0.28 0.24 0.21
L/200 14.50 9.28 5.75 3.62 2.43 1.70 1.24 0.93 0.72 0.57 0.45 0.37 0.30 0.25 0.21 0.18 0.16
L/250 14.50 7.95 4.60 2.90 1.94 1.36 0.99 0.75 0.57 0.45 0.36 0.29 0.24 0.20 0.17 0.14 0.12
0.45
SLU 17.00 10.88 7.56 5.55 4.25 3.36 2.72 2.25 1.89 1.61 1.39 1.21 1.06 0.94 0.84 0.75 0.68
L/150 17.00 10.88 7.56 5.55 3.89 2.73 1.99 1.49 1.15 0.91 0.72 0.59 0.49 0.40 0.34 0.29 0.25
L/200 17.00 10.88 6.91 4.35 2.91 2.05 1.49 1.12 0.86 0.68 0.54 0.44 0.36 0.30 0.26 0.22 0.19
L/250 17.00 9.55 5.53 3.48 2.33 1.64 1.19 0.90 0.69 0.54 0.43 0.35 0.29 0.24 0.20 0.17 0.15
0.50
SLU 21.50 13.76 9.56 7.02 5.38 4.25 3.44 2.84 2.39 2.04 1.76 1.53 1.34 1.19 1.06 0.95 0.86
L/150 21.50 13.76 9.56 6.71 4.49 3.16 2.30 1.73 1.33 1.05 0.84 0.68 0.56 0.47 0.39 0.34 0.29
L/200 21.50 13.76 7.99 5.03 3.37 2.37 1.73 1.30 1.00 0.79 0.63 0.51 0.42 0.35 0.30 0.25 0.22
L/250 21.50 11.04 6.39 4.02 2.70 1.89 1.38 1.04 0.80 0.63 0.50 0.41 0.34 0.28 0.24 0.20 0.17
0.60
SLU 31.50 20.16 14.00 10.29 7.88 6.22 5.04 4.17 3.50 2.98 2.57 2.24 1.97 1.74 1.56 1.40 1.26
L/150 31.50 20.16 13.54 8.53 5.71 4.01 2.92 2.20 1.69 1.33 1.07 0.87 0.71 0.60 0.50 0.43 0.37
L/200 31.50 17.55 10.15 6.39 4.28 3.01 2.19 1.65 1.27 1.00 0.80 0.65 0.54 0.45 0.38 0.32 0.27
L/250 27.42 14.04 8.12 5.12 3.43 2.41 1.75 1.32 1.02 0.80 0.64 0.52 0.43 0.36 0.30 0.26 0.22
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.11 0.98 0.87 0.78 0.71 0.64 0.58
L/150 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.11 0.98 0.87 0.78 0.69 0.59 0.50
L/200 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.10 0.90 0.74 0.62 0.52 0.44 0.38
L/250 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.40 1.10 0.88 0.72 0.59 0.49 0.42 0.35 0.30
0.45
SLU 10.50 7.48 5.61 4.38 3.51 2.89 2.41 2.05 1.76 1.53 1.34 1.19 1.06 0.94 0.84 0.75 0.68
L/150 10.50 7.48 5.61 4.38 3.51 2.89 2.41 2.05 1.76 1.53 1.34 1.19 1.06 0.94 0.83 0.71 0.61
L/200 10.50 7.48 5.61 4.38 3.51 2.89 2.41 2.05 1.76 1.53 1.33 1.08 0.89 0.74 0.62 0.53 0.45
L/250 10.50 7.48 5.61 4.38 3.51 2.89 2.41 2.05 1.68 1.32 1.06 0.86 0.71 0.59 0.50 0.42 0.36
0.50
SLU 13.27 9.45 7.10 5.53 4.44 3.65 3.05 2.59 2.23 1.93 1.70 1.50 1.34 1.19 1.06 0.95 0.86
L/150 13.27 9.45 7.10 5.53 4.44 3.65 3.05 2.59 2.23 1.93 1.70 1.50 1.34 1.14 0.96 0.82 0.70
L/200 13.27 9.45 7.10 5.53 4.44 3.65 3.05 2.59 2.23 1.92 1.53 1.25 1.03 0.86 0.72 0.61 0.53
L/250 13.27 9.45 7.10 5.53 4.44 3.65 3.05 2.53 1.95 1.53 1.23 1.00 0.82 0.69 0.58 0.49 0.42
0.60
SLU 18.10 12.99 9.81 7.69 6.20 5.11 4.29 3.65 3.14 2.74 2.41 2.13 1.90 1.71 1.54 1.40 1.26
L/150 18.10 12.99 9.81 7.69 6.20 5.11 4.29 3.65 3.14 2.74 2.41 2.11 1.74 1.45 1.22 1.04 0.89
L/200 18.10 12.99 9.81 7.69 6.20 5.11 4.29 3.65 3.10 2.44 1.95 1.59 1.31 1.09 0.92 0.78 0.67
L/250 18.10 12.99 9.81 7.69 6.20 5.11 4.28 3.22 2.48 1.95 1.56 1.27 1.04 0.87 0.73 0.62 0.53
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
16/1911-6
16.5.137,5.1100
ROOF AND WALLS PROFILES
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
0.40
SLU 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.11 0.98 0.87 0.78 0.71 0.64 0.58
L/150 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.11 0.98 0.87 0.78 0.69 0.59 0.50
L/200 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.44 1.26 1.10 0.90 0.74 0.62 0.52 0.44 0.38
L/250 8.30 5.96 4.50 3.53 2.85 2.35 1.97 1.68 1.40 1.10 0.88 0.72 0.59 0.49 0.42 0.35 0.30
0.45
SLU 12.67 9.06 6.82 5.33 4.29 3.53 2.95 2.51 2.16 1.88 1.65 1.46 1.30 1.17 1.05 0.94 0.85
L/150 12.67 9.06 6.82 5.33 4.29 3.53 2.95 2.51 2.16 1.88 1.65 1.44 1.18 0.99 0.83 0.71 0.61
L/200 12.67 9.06 6.82 5.33 4.29 3.53 2.95 2.51 2.11 1.66 1.33 1.08 0.89 0.74 0.62 0.53 0.45
L/250 12.67 9.06 6.82 5.33 4.29 3.53 2.91 2.19 1.68 1.32 1.06 0.86 0.71 0.59 0.50 0.42 0.36
0.50
SLU 16.01 11.45 8.62 6.74 5.42 4.46 3.73 3.17 2.73 2.38 2.09 1.85 1.65 1.48 1.33 1.19 1.08
L/150 16.01 11.45 8.62 6.74 5.42 4.46 3.73 3.17 2.73 2.38 2.05 1.66 1.37 1.14 0.96 0.82 0.70
L/200 16.01 11.45 8.62 6.74 5.42 4.46 3.73 3.16 2.44 1.92 1.53 1.25 1.03 0.86 0.72 0.61 0.53
L/250 16.01 11.45 8.62 6.74 5.42 4.46 3.37 2.53 1.95 1.53 1.23 1.00 0.82 0.69 0.58 0.49 0.42
0.60
SLU 21.79 15.70 11.89 9.35 7.55 6.23 5.24 4.46 3.85 3.36 2.96 2.62 2.34 2.10 1.90 1.72 1.57
L/150 21.79 15.70 11.89 9.35 7.55 6.23 5.24 4.46 3.85 3.25 2.60 2.11 1.74 1.45 1.22 1.04 0.89
L/200 21.79 15.70 11.89 9.35 7.55 6.23 5.24 4.02 3.10 2.44 1.95 1.59 1.31 1.09 0.92 0.78 0.67
L/250 21.79 15.70 11.89 9.35 7.55 5.87 4.28 3.22 2.48 1.95 1.56 1.27 1.04 0.87 0.73 0.62 0.53
ables containing loads determined according to EC3-1-3-2001
Te calculation load for SLU must include thesafety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
7/21/2019 catalog Megaprofil 2013 (1).pdf
17/1911-7
ROOF AND WALLS PROFILES
35.207.1035
APPLICAION
Walls made of panels with one layer
Walls made of panels with double layer (with interior chamber)
The vertical positioning is the standard one, but they may also be mounted horizontally
They may be used for the construction of containers, false ceilings, for fencing the sites, for interior walls
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m
2
thickness 0.40| 0.50 | 0.60 | 0.75 mmPolyester-silicone 25 14 standard colours thickness 0.40| 0.45 | 0.50 | 0.60 | 0.75 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.81 57.70 59.30 4.45 2.54 610.00
0.45 4.29 67.90 80.10 5.24 2.99 970.00
0.50 4.76 82.00 90.30 6.32 3.61 1350.00
0.60 5.24 104.50 107.50 8.06 4.60 2094.00
0.75 7.12 132.30 136.80 10.20 5.82 2852.00
A small channel on the side of
the plate ensures the perfect
mounting and fastening of the
screws.
Maximum length 10 m
7/21/2019 catalog Megaprofil 2013 (1).pdf
18/1911-8
35.207.1035
ROOF AND WALLS PROFILES
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 7.38 4.72 3.28 2.41 1.84 1.46 1.18 0.98 0.82 0.70 0.60 0.52 0.46 0.41 0.36 0.33 0.30
L/150 7.38 4.72 2.77 1.74 1.17 0.82 0.60 0.45 0.35 0.27 0.22 0.18 0.15 0.12 0.10 0.09 0.07
L/200 7.01 3.59 2.08 1.31 0.88 0.62 0.45 0.34 0.26 0.20 0.16 0.13 0.11 0.09 0.08 0.07 0.06
L/250 5.61 2.87 1.66 1.05 0.70 0.49 0.36 0.27 0.21 0.16 0.13 0.11 0.09 0.07 0.06 0.05 0.04
0.45
SLU 10.00 6.40 4.44 3.27 2.50 1.98 1.60 1.32 1.11 0.95 0.82 0.71 0.63 0.55 0.49 0.44 0.40
L/150 10.00 5.63 3.26 2.05 1.38 0.97 0.70 0.53 0.41 0.32 0.26 0.21 0.17 0.14 0.12 0.10 0.09
L/200 8.25 4.23 2.45 1.54 1.03 0.72 0.53 0.40 0.31 0.24 0.19 0.16 0.13 0.11 0.09 0.08 0.07
L/250 6.60 3.38 1.96 1.23 0.83 0.58 0.42 0.32 0.24 0.19 0.15 0.13 0.10 0.09 0.07 0.06 0.05
0.50
SLU 11.25 7.20 5.00 3.67 2.81 2.22 1.80 1.49 1.25 1.07 0.92 0.80 0.70 0.62 0.56 0.50 0.45
L/150 11.25 6.80 3.93 2.48 1.66 1.17 0.85 0.64 0.49 0.39 0.31 0.25 0.21 0.17 0.15 0.12 0.11
L/200 9.95 5.10 2.95 1.86 1.24 0.87 0.64 0.48 0.37 0.29 0.23 0.19 0.16 0.13 0.11 0.09 0.08
L/250 7.96 4.08 2.36 1.49 1.00 0.70 0.51 0.38 0.29 0.23 0.19 0.15 0.12 0.10 0.09 0.07 0.06
0.60
SLU 13.50 8.64 6.00 4.41 3.38 2.67 2.16 1.79 1.50 1.28 1.10 0.96 0.84 0.75 0.67 0.60 0.54
L/150 13.50 8.64 5.02 3.16 2.12 1.49 1.08 0.81 0.63 0.49 0.39 0.32 0.26 0.22 0.19 0.16 0.14
L/200 12.69 6.50 3.76 2.37 1.59 1.11 0.81 0.61 0.47 0.37 0.30 0.24 0.20 0.17 0.14 0.12 0.10
L/250 10.16 5.20 3.01 1.89 1.27 0.89 0.65 0.49 0.38 0.30 0.24 0.19 0.16 0.13 0.11 0.09 0.08
0.75
SLU 17.13 10.96 7.61 5.59 4.28 3.38 2.74 2.26 1.90 1.62 1.40 1.22 1.07 0.95 0.85 0.76 0.69
L/150 17.13 10.96 6.35 4.00 2.68 1.88 1.37 1.03 0.79 0.62 0.50 0.41 0.33 0.28 0.24 0.20 0.17
L/200 16.07 8.23 4.76 3.00 2.01 1.41 1.03 0.77 0.60 0.47 0.37 0.30 0.25 0.21 0.18 0.15 0.13
L/250 12.85 6.58 3.81 2.40 1.61 1.13 0.82 0.62 0.48 0.37 0.30 0.24 0.20 0.17 0.14 0.12 0.10
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 4.03 2.90 2.20 1.73 1.40 1.16 0.97 0.83 0.72 0.62 0.55 0.49 0.44 0.39 0.35 0.32 0.29
L/150 4.03 2.90 2.20 1.73 1.40 1.16 0.97 0.83 0.72 0.62 0.53 0.43 0.36 0.30 0.25 0.21 0.18
L/200 4.03 2.90 2.20 1.73 1.40 1.16 0.97 0.82 0.63 0.50 0.40 0.32 0.27 0.22 0.19 0.16 0.14
L/250 4.03 2.90 2.20 1.73 1.40 1.16 0.88 0.66 0.51 0.40 0.32 0.26 0.21 0.18 0.15 0.13 0.11
0.45
SLU 5.95 4.26 3.21 2.51 2.02 1.66 1.39 1.18 1.02 0.88 0.78 0.69 0.61 0.55 0.49 0.44 0.40
L/150 5.95 4.26 3.21 2.51 2.02 1.66 1.39 1.18 0.99 0.78 0.63 0.51 0.42 0.35 0.29 0.25 0.21
L/200 5.95 4.26 3.21 2.51 2.02 1.66 1.29 0.97 0.75 0.59 0.47 0.38 0.31 0.26 0.22 0.19 0.16
L/250 5.95 4.26 3.21 2.51 2.01 1.41 1.03 0.77 0.60 0.47 0.38 0.31 0.25 0.21 0.18 0.15 0.13
0.50
SLU 7.44 5.26 3.92 3.05 2.43 1.99 1.66 1.41 1.21 1.05 0.92 0.80 0.70 0.62 0.56 0.50 0.45
L/150 7.44 5.26 3.92 3.05 2.43 1.99 1.66 1.41 1.20 0.94 0.76 0.61 0.51 0.42 0.36 0.30 0.26
L/200 7.44 5.26 3.92 3.05 2.43 1.99 1.55 1.17 0.90 0.71 0.57 0.46 0.38 0.32 0.27 0.23 0.19
L/250 7.44 5.26 3.92 3.05 2.43 1.71 1.24 0.93 0.72 0.57 0.45 0.37 0.30 0.25 0.21 0.18 0.16
0.60
SLU 10.00 6.97 5.14 3.96 3.14 2.55 2.12 1.79 1.50 1.28 1.10 0.96 0.84 0.75 0.67 0.60 0.54
L/150 10.00 6.97 5.14 3.96 3.14 2.55 2.12 1.79 1.50 1.20 0.96 0.78 0.65 0.54 0.45 0.39 0.33
L/200 10.00 6.97 5.14 3.96 3.14 2.55 1.98 1.49 1.15 0.90 0.72 0.59 0.48 0.40 0.34 0.29 0.25
L/250 10.00 6.97 5.14 3.96 3.10 2.17 1.59 1.19 0.92 0.72 0.58 0.47 0.39 0.32 0.27 0.23 0.20
0.75
SLU 13.05 9.06 6.67 5.12 4.05 3.29 2.73 2.26 1.90 1.62 1.40 1.22 1.07 0.95 0.85 0.76 0.69
L/150 13.05 9.06 6.67 5.12 4.05 3.29 2.73 2.26 1.90 1.52 1.22 0.99 0.82 0.68 0.57 0.49 0.42
L/200 13.05 9.06 6.67 5.12 4.05 3.29 2.51 1.88 1.45 1.14 0.91 0.74 0.61 0.51 0.43 0.37 0.31
L/250 13.05 9.06 6.67 5.12 3.92 2.75 2.01 1.51 1.16 0.91 0.73 0.59 0.49 0.41 0.34 0.29 0.25
MRRO011-0
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
19/1911-9
ROOF AND WALLS PROFILES
35.207.1035
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 4.84 3.50 2.67 2.10 1.70 1.41 1.19 1.01 0.88 0.77 0.67 0.60 0.54 0.48 0.44 0.40 0.36
L/150 4.84 3.50 2.67 2.10 1.70 1.41 1.15 0.86 0.67 0.52 0.42 0.34 0.28 0.23 0.20 0.17 0.14
L/200 4.84 3.50 2.67 2.10 1.68 1.18 0.86 0.65 0.50 0.39 0.31 0.26 0.21 0.18 0.15 0.13 0.11
L/250 4.84 3.50 2.67 2.01 1.35 0.95 0.69 0.52 0.40 0.31 0.25 0.20 0.17 0.14 0.12 0.10 0.09
0.45
SLU 7.17 5.15 3.89 3.05 2.46 2.03 1.70 1.45 1.25 1.09 0.95 0.85 0.75 0.68 0.61 0.55 0.50
L/150 7.17 5.15 3.89 3.05 2.46 1.86 1.35 1.02 0.78 0.62 0.49 0.40 0.33 0.28 0.23 0.20 0.17
L/200 7.17 5.15 3.89 2.96 1.98 1.39 1.02 0.76 0.59 0.46 0.37 0.30 0.25 0.21 0.17 0.15 0.13
L/250 7.17 5.15 3.76 2.37 1.59 1.11 0.81 0.61 0.47 0.37 0.30 0.24 0.20 0.17 0.14 0.12 0.10
0.50
SLU 9.00 6.39 4.78 3.72 2.98 2.44 2.04 1.73 1.48 1.29 1.13 1.00 0.88 0.78 0.69 0.62 0.56
L/150 9.00 6.39 4.78 3.72 2.98 2.24 1.63 1.23 0.95 0.74 0.60 0.48 0.40 0.33 0.28 0.24 0.20
L/200 9.00 6.39 4.78 3.57 2.39 1.68 1.23 0.92 0.71 0.56 0.45 0.36 0.30 0.25 0.21 0.18 0.15
L/250 9.00 6.39 4.54 2.86 1.91 1.34 0.98 0.74 0.57 0.45 0.36 0.29 0.24 0.20 0.17 0.14 0.12
0.60
SLU 12.15 8.49 6.29 4.85 3.85 3.14 2.61 2.20 1.88 1.60 1.38 1.20 1.05 0.93 0.83 0.75 0.68
L/150 12.15 8.49 6.29 4.85 3.85 2.86 2.08 1.57 1.21 0.95 0.76 0.62 0.51 0.42 0.36 0.30 0.26
L/200 12.15 8.49 6.29 4.56 3.05 2.14 1.56 1.17 0.90 0.71 0.57 0.46 0.38 0.32 0.27 0.23 0.20
L/250 12.15 8.49 5.79 3.64 2.44 1.71 1.25 0.94 0.72 0.57 0.46 0.37 0.31 0.25 0.21 0.18 0.16
0.75
SLU 15.87 11.06 8.16 6.28 4.98 4.05 3.36 2.83 2.38 2.03 1.75 1.52 1.34 1.19 1.06 0.95 0.86
L/150 15.87 11.06 8.16 6.28 4.98 3.62 2.64 1.98 1.53 1.20 0.96 0.78 0.64 0.54 0.45 0.38 0.33
L/200 15.87 11.06 8.16 5.76 3.86 2.71 1.98 1.49 1.14 0.90 0.72 0.59 0.48 0.40 0.34 0.29 0.25
L/250 15.87 11.06 7.32 4.61 3.09 2.17 1.58 1.19 0.92 0.72 0.58 0.47 0.39 0.32 0.27 0.23 0.20
ables containing loads determined according to EC3-1-3-2001Te calculation load for SLU must include thesafety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
7/21/2019 catalog Megaprofil 2013 (1).pdf
20/1911-10
38.250.1000
ROOF AND WALLS PROFILES
APPLICAION
Profiled sheet for pitched roofs
For industrial, agricultural, and commercial applications: industrial halls, warehouses, garages etc.
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.40 | 0.45 | 0.50 | 0.60 | 0.75 mm
Polyester-silicone 25 14 standard colours thickness 0.40 | 0.45 | 0.50 | 0.60 | 0.75 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHT MAX. BENDINGMOMENT
MAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.94 87.30 87.30 9.20 3.84 717.00
0.45 4.44 94.80 94.80 10.60 4.17 886.00
0.50 4.92 103.30 103.30 11.50 4.50 1070.00
0.60 5.42 117.20 117.20 13.30 5.16 1480.00
0.75 7.34 150.50 150.50 16.50 6.62 2198.00
7/21/2019 catalog Megaprofil 2013 (1).pdf
21/1911-11
ROOF AND WALLS PROFILES
38.250.1000
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 10.88 6.96 4.83 3.55 2.72 2.15 1.74 1.44 1.21 1.03 0.89 0.77 0.68 0.60 0.54 0.48 0.44
L/150 10.88 6.96 4.83 3.55 2.42 1.70 1.24 0.93 0.72 0.56 0.45 0.37 0.30 0.25 0.21 0.18 0.15
L/200 10.88 6.96 4.29 2.70 1.81 1.27 0.93 0.70 0.54 0.42 0.34 0.27 0.23 0.19 0.16 0.14 0.12
L/250 10.88 5.94 3.43 2.16 1.45 1.02 0.74 0.56 0.43 0.34 0.27 0.22 0.18 0.15 0.13 0.11 0.09
0.45
SLU 11.88 7.60 5.28 3.88 2.97 2.35 1.90 1.57 1.32 1.12 0.97 0.84 0.74 0.66 0.59 0.53 0.48
L/150 11.88 7.60 5.28 3.88 2.78 1.95 1.42 1.07 0.82 0.65 0.52 0.42 0.35 0.29 0.24 0.21 0.18
L/200 11.88 7.60 4.95 3.12 2.09 1.47 1.07 0.80 0.62 0.49 0.39 0.32 0.26 0.22 0.18 0.16 0.13
L/250 11.88 6.84 3.96 2.49 1.67 1.17 0.85 0.64 0.49 0.39 0.31 0.25 0.21 0.17 0.15 0.12 0.11
0.50
SLU 12.88 8.24 5.72 4.20 3.22 2.54 2.06 1.70 1.43 1.22 1.05 0.92 0.80 0.71 0.64 0.57 0.52
L/150 12.88 8.24 5.72 4.20 3.02 2.12 1.55 1.16 0.89 0.70 0.56 0.46 0.38 0.31 0.27 0.23 0.19
L/200 12.88 8.24 5.37 3.38 2.26 1.59 1.16 0.87 0.67 0.53 0.42 0.34 0.28 0.24 0.20 0.17 0.14
L/250 12.88 7.42 4.29 2.70 1.81 1.27 0.93 0.70 0.54 0.42 0.34 0.27 0.23 0.19 0.16 0.14 0.12
0.60
SLU 14.63 9.36 6.50 4.78 3.66 2.89 2.34 1.93 1.63 1.38 1.19 1.04 0.91 0.81 0.72 0.65 0.59
L/150 14.63 9.36 6.50 4.78 3.49 2.45 1.79 1.34 1.03 0.81 0.65 0.53 0.44 0.36 0.31 0.26 0.22
L/200 14.63 9.36 6.21 3.91 2.62 1.84 1.34 1.01 0.78 0.61 0.49 0.40 0.33 0.27 0.23 0.20 0.17
L/250 14.63 8.58 4.97 3.13 2.09 1.47 1.07 0.81 0.62 0.49 0.39 0.32 0.26 0.22 0.18 0.16 0.13
0.75
SLU 18.81 12.04 8.36 6.14 4.70 3.72 3.01 2.49 2.09 1.78 1.54 1.34 1.18 1.04 0.93 0.83 0.75
L/150 18.81 12.04 8.36 6.14 4.33 3.04 2.22 1.67 1.28 1.01 0.81 0.66 0.54 0.45 0.38 0.32 0.28
L/200 18.81 12.04 7.70 4.85 3.25 2.28 1.66 1.25 0.96 0.76 0.61 0.49 0.41 0.34 0.29 0.24 0.21
L/250 18.81 10.64 6.16 3.88 2.60 1.83 1.33 1.00 0.77 0.61 0.48 0.39 0.32 0.27 0.23 0.19 0.17
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 5.19 3.79 2.91 2.31 1.88 1.56 1.32 1.13 0.98 0.86 0.76 0.68 0.60 0.55 0.49 0.45 0.41
L/150 5.19 3.79 2.91 2.31 1.88 1.56 1.32 1.13 0.98 0.86 0.76 0.68 0.60 0.55 0.49 0.44 0.38
L/200 5.19 3.79 2.91 2.31 1.88 1.56 1.32 1.13 0.98 0.86 0.76 0.67 0.55 0.46 0.39 0.33 0.28
L/250 5.19 3.79 2.91 2.31 1.88 1.56 1.32 1.13 0.98 0.82 0.66 0.54 0.44 0.37 0.31 0.26 0.23
0.45
SLU 6.11 4.43 3.38 2.67 2.16 1.79 1.51 1.29 1.12 0.98 0.86 0.76 0.68 0.61 0.56 0.51 0.46
L/150 6.11 4.43 3.38 2.67 2.16 1.79 1.51 1.29 1.12 0.98 0.86 0.76 0.68 0.61 0.56 0.51 0.43
L/200 6.11 4.43 3.38 2.67 2.16 1.79 1.51 1.29 1.12 0.98 0.86 0.76 0.64 0.53 0.45 0.38 0.33
L/250 6.11 4.43 3.38 2.67 2.16 1.79 1.51 1.29 1.12 0.95 0.76 0.62 0.51 0.42 0.36 0.30 0.26
0.50
SLU 7.05 5.08 3.85 3.03 2.45 2.02 1.70 1.45 1.25 1.09 0.96 0.85 0.76 0.68 0.62 0.56 0.51
L/150 7.05 5.08 3.85 3.03 2.45 2.02 1.70 1.45 1.25 1.09 0.96 0.85 0.76 0.68 0.62 0.55 0.47
L/200 7.05 5.08 3.85 3.03 2.45 2.02 1.70 1.45 1.25 1.09 0.96 0.84 0.69 0.58 0.48 0.41 0.35
L/250 7.05 5.08 3.85 3.03 2.45 2.02 1.70 1.45 1.25 1.03 0.82 0.67 0.55 0.46 0.39 0.33 0.28
0.60
SLU 8.90 6.35 4.77 3.73 2.99 2.46 2.06 1.75 1.50 1.31 1.15 1.01 0.90 0.81 0.72 0.65 0.59
L/150 8.90 6.35 4.77 3.73 2.99 2.46 2.06 1.75 1.50 1.31 1.15 1.01 0.90 0.81 0.72 0.64 0.54
L/200 8.90 6.35 4.77 3.73 2.99 2.46 2.06 1.75 1.50 1.31 1.15 0.97 0.80 0.67 0.56 0.48 0.41
L/250 8.90 6.35 4.77 3.73 2.99 2.46 2.06 1.75 1.50 1.19 0.95 0.78 0.64 0.53 0.45 0.38 0.33
0.75
SLU 12.29 8.70 6.50 5.05 4.04 3.30 2.76 2.33 2.00 1.74 1.52 1.34 1.18 1.04 0.93 0.83 0.75
L/150 12.29 8.70 6.50 5.05 4.04 3.30 2.76 2.33 2.00 1.74 1.52 1.34 1.18 1.04 0.93 0.79 0.68
L/200 12.29 8.70 6.50 5.05 4.04 3.30 2.76 2.33 2.00 1.74 1.48 1.20 0.99 0.83 0.70 0.59 0.51
L/250 12.29 8.70 6.50 5.05 4.04 3.30 2.76 2.33 1.88 1.48 1.18 0.96 0.79 0.66 0.56 0.47 0.41
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
22/191
38.250.1000
ROOF AND WALLS PROFILES
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 6.22 4.56 3.50 2.79 2.28 1.90 1.61 1.38 1.20 1.05 0.93 0.83 0.74 0.67 0.61 0.55 0.50
L/150 6.22 4.56 3.50 2.79 2.28 1.90 1.61 1.38 1.20 1.05 0.87 0.70 0.58 0.48 0.41 0.35 0.30
L/200 6.22 4.56 3.50 2.79 2.28 1.90 1.61 1.34 1.03 0.81 0.65 0.53 0.44 0.36 0.31 0.26 0.22
L/250 6.22 4.56 3.50 2.79 2.28 1.90 1.43 1.07 0.83 0.65 0.52 0.42 0.35 0.29 0.24 0.21 0.18
0.45
SLU 7.33 5.34 4.08 3.23 2.63 2.18 1.84 1.58 1.36 1.19 1.05 0.94 0.84 0.76 0.68 0.62 0.57
L/150 7.33 5.34 4.08 3.23 2.63 2.18 1.84 1.58 1.36 1.19 1.00 0.81 0.67 0.56 0.47 0.40 0.34
L/200 7.33 5.34 4.08 3.23 2.63 2.18 1.84 1.54 1.19 0.94 0.75 0.61 0.50 0.42 0.35 0.30 0.26
L/250 7.33 5.34 4.08 3.23 2.63 2.18 1.64 1.24 0.95 0.75 0.60 0.49 0.40 0.33 0.28 0.24 0.21
0.50
SLU 8.47 6.13 4.66 3.68 2.98 2.47 2.08 1.77 1.53 1.34 1.18 1.05 0.94 0.84 0.76 0.69 0.63
L/150 8.47 6.13 4.66 3.68 2.98 2.47 2.08 1.77 1.53 1.34 1.08 0.88 0.73 0.60 0.51 0.43 0.37
L/200 8.47 6.13 4.66 3.68 2.98 2.47 2.08 1.67 1.29 1.01 0.81 0.66 0.54 0.45 0.38 0.33 0.28
L/250 8.47 6.13 4.66 3.68 2.98 2.45 1.78 1.34 1.03 0.81 0.65 0.53 0.44 0.36 0.31 0.26 0.22
0.60
SLU 10.73 7.68 5.79 4.54 3.65 3.01 2.52 2.14 1.84 1.61 1.41 1.25 1.11 1.00 0.90 0.81 0.73
L/150 10.73 7.68 5.79 4.54 3.65 3.01 2.52 2.14 1.84 1.56 1.25 1.02 0.84 0.70 0.59 0.50 0.43
L/200 10.73 7.68 5.79 4.54 3.65 3.01 2.52 1.94 1.49 1.17 0.94 0.76 0.63 0.52 0.44 0.38 0.32
L/250 10.73 7.68 5.79 4.54 3.65 2.83 2.06 1.55 1.19 0.94 0.75 0.61 0.50 0.42 0.35 0.30 0.26
0.75
SLU 14.86 10.55 7.91 6.16 4.94 4.05 3.38 2.87 2.46 2.14 1.88 1.66 1.47 1.30 1.16 1.04 0.94
L/150 14.86 10.55 7.91 6.16 4.94 4.05 3.38 2.87 2.46 1.94 1.55 1.26 1.04 0.87 0.73 0.62 0.53
L/200 14.86 10.55 7.91 6.16 4.94 4.05 3.20 2.40 1.85 1.46 1.17 0.95 0.78 0.65 0.55 0.47 0.40
L/250 14.86 10.55 7.91 6.16 4.94 3.51 2.56 1.92 1.48 1.16 0.93 0.76 0.62 0.52 0.44 0.37 0.32
ables containing loads determined according to EC3-1-3-2001Te calculation load for SLU must include thesafety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
1-12
7/21/2019 catalog Megaprofil 2013 (1).pdf
23/191
ROOF AND WALLS PROFILES
45.333.1000
APPLICAION
Roof
PRODUC FEAURES
Length Standard length of up to max. 10 mMetal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.25| 0.40 | 0.50 | 0.60 mm
Polyester-silicone 25 14 standard colours thickness 0.40| 0.45 | 0.50 | 0.60 | 0.75 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.94 73.60 73.60 11.50 3.24 619.00
0.45 4.44 80.00 80.00 12.50 3.52 738.50
0.50 4.92 86.10 86.10 13.50 3.79 858.00
0.60 5.42 98.60 98.60 15.50 4.34 1097.00
0.75 7.37 117.50 117.50 18.40 5.17 1500.00
1-13
7/21/2019 catalog Megaprofil 2013 (1).pdf
24/191
45.333.1000
ROOF AND WALLS PROFILES
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 9.25 5.92 4.11 3.02 2.31 1.83 1.48 1.22 1.03 0.88 0.76 0.66 0.58 0.51 0.46 0.41 0.37
L/150 9.25 5.92 4.11 3.02 2.31 1.83 1.48 1.16 0.89 0.70 0.56 0.46 0.38 0.31 0.27 0.23 0.19
L/200 9.25 5.92 4.11 3.02 2.26 1.59 1.16 0.87 0.67 0.53 0.42 0.34 0.28 0.24 0.20 0.17 0.14
L/250 9.25 5.92 4.11 2.70 1.81 1.27 0.93 0.70 0.54 0.42 0.34 0.27 0.23 0.19 0.16 0.14 0.12
0.45
SLU 10.00 6.40 4.44 3.27 2.50 1.98 1.60 1.32 1.11 0.95 0.82 0.71 0.63 0.55 0.49 0.44 0.40
L/150 10.00 6.40 4.44 3.27 2.50 1.98 1.60 1.26 0.97 0.76 0.61 0.50 0.41 0.34 0.29 0.24 0.21
L/200 10.00 6.40 4.44 3.27 2.46 1.73 1.26 0.95 0.73 0.57 0.46 0.37 0.31 0.26 0.22 0.18 0.16
L/250 10.00 6.40 4.44 2.94 1.97 1.38 1.01 0.76 0.58 0.46 0.37 0.30 0.25 0.21 0.17 0.15 0.13
0.50
SLU 10.75 6.88 4.78 3.51 2.69 2.12 1.72 1.42 1.19 1.02 0.88 0.76 0.67 0.60 0.53 0.48 0.43
L/150 10.75 6.88 4.78 3.51 2.69 2.12 1.72 1.36 1.05 0.83 0.66 0.54 0.44 0.37 0.31 0.26 0.23
L/200 10.75 6.88 4.78 3.51 2.66 1.87 1.36 1.02 0.79 0.62 0.50 0.40 0.33 0.28 0.23 0.20 0.17
L/250 10.75 6.88 4.78 3.17 2.13 1.49 1.09 0.82 0.63 0.50 0.40 0.32 0.27 0.22 0.19 0.16 0.14
0.60
SLU 12.25 7.84 5.44 4.00 3.06 2.42 1.96 1.62 1.36 1.16 1.00 0.87 0.77 0.68 0.60 0.54 0.49
L/150 12.25 7.84 5.44 4.00 3.06 2.42 1.96 1.57 1.21 0.95 0.76 0.62 0.51 0.42 0.36 0.30 0.26
L/200 12.25 7.84 5.44 4.00 3.05 2.14 1.56 1.17 0.90 0.71 0.57 0.46 0.38 0.32 0.27 0.23 0.20
L/250 12.25 7.84 5.44 3.64 2.44 1.71 1.25 0.94 0.72 0.57 0.46 0.37 0.31 0.25 0.21 0.18 0.16
0.75
SLU 14.75 9.44 6.56 4.82 3.69 2.91 2.36 1.95 1.64 1.40 1.20 1.05 0.92 0.82 0.73 0.65 0.59
L/150 14.75 9.44 6.56 4.82 3.69 2.91 2.36 1.86 1.43 1.13 0.90 0.73 0.60 0.50 0.42 0.36 0.31
L/200 14.75 9.44 6.56 4.82 3.62 2.54 1.85 1.39 1.07 0.84 0.68 0.55 0.45 0.38 0.32 0.27 0.23
L/250 14.75 9.44 6.56 4.33 2.90 2.04 1.48 1.11 0.86 0.68 0.54 0.44 0.36 0.30 0.25 0.22 0.19
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 4.46 3.25 2.49 1.98 1.61 1.34 1.13 0.97 0.84 0.73 0.65 0.58 0.52 0.47 0.42 0.38 0.35
L/150 4.46 3.25 2.49 1.98 1.61 1.34 1.13 0.97 0.84 0.73 0.65 0.58 0.52 0.47 0.42 0.38 0.35
L/200 4.46 3.25 2.49 1.98 1.61 1.34 1.13 0.97 0.84 0.73 0.65 0.58 0.52 0.47 0.42 0.38 0.35
L/250 4.46 3.25 2.49 1.98 1.61 1.34 1.13 0.97 0.84 0.73 0.65 0.58 0.52 0.46 0.39 0.33 0.28
0.45
SLU 5.11 3.71 2.83 2.24 1.81 1.50 1.27 1.08 0.94 0.82 0.72 0.64 0.57 0.52 0.47 0.42 0.39
L/150 5.11 3.71 2.83 2.24 1.81 1.50 1.27 1.08 0.94 0.82 0.72 0.64 0.57 0.52 0.47 0.42 0.39
L/200 5.11 3.71 2.83 2.24 1.81 1.50 1.27 1.08 0.94 0.82 0.72 0.64 0.57 0.52 0.47 0.42 0.38
L/250 5.11 3.71 2.83 2.24 1.81 1.50 1.27 1.08 0.94 0.82 0.72 0.64 0.57 0.50 0.42 0.36 0.31
0.50
SLU 5.75 4.16 3.16 2.49 2.01 1.67 1.40 1.20 1.03 0.90 0.79 0.70 0.63 0.57 0.51 0.46 0.42
L/150 5.75 4.16 3.16 2.49 2.01 1.67 1.40 1.20 1.03 0.90 0.79 0.70 0.63 0.57 0.51 0.46 0.42
L/200 5.75 4.16 3.16 2.49 2.01 1.67 1.40 1.20 1.03 0.90 0.79 0.70 0.63 0.57 0.51 0.46 0.41
L/250 5.75 4.16 3.16 2.49 2.01 1.67 1.40 1.20 1.03 0.90 0.79 0.70 0.63 0.54 0.46 0.39 0.33
0.60
SLU 6.99 5.02 3.79 2.98 2.40 1.98 1.66 1.41 1.22 1.06 0.93 0.83 0.74 0.66 0.60 0.54 0.49
L/150 6.99 5.02 3.79 2.98 2.40 1.98 1.66 1.41 1.22 1.06 0.93 0.83 0.74 0.66 0.60 0.54 0.49
L/200 6.99 5.02 3.79 2.98 2.40 1.98 1.66 1.41 1.22 1.06 0.93 0.83 0.74 0.66 0.60 0.54 0.48
L/250 6.99 5.02 3.79 2.98 2.40 1.98 1.66 1.41 1.22 1.06 0.93 0.83 0.74 0.62 0.52 0.44 0.38
0.75
SLU 9.00 6.42 4.82 3.76 3.02 2.48 2.08 1.76 1.52 1.32 1.16 1.02 0.91 0.82 0.73 0.65 0.59
L/150 9.00 6.42 4.82 3.76 3.02 2.48 2.08 1.76 1.52 1.32 1.16 1.02 0.91 0.82 0.73 0.65 0.59
L/200 9.00 6.42 4.82 3.76 3.02 2.48 2.08 1.76 1.52 1.32 1.16 1.02 0.91 0.82 0.73 0.65 0.57
L/250 9.00 6.42 4.82 3.76 3.02 2.48 2.08 1.76 1.52 1.32 1.16 1.02 0.88 0.74 0.62 0.53 0.45
1-14
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
25/191
ROOF AND WALLS PROFILES
45.333.1000
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 3.80 4.00
0.40
SLU 5.34 3.91 3.00 2.39 1.95 1.62 1.37 1.18 1.02 0.90 0.79 0.71 0.63 0.57 0.52 0.47 0.43
L/150 5.34 3.91 3.00 2.39 1.95 1.62 1.37 1.18 1.02 0.90 0.79 0.71 0.63 0.57 0.51 0.43 0.37
L/200 5.34 3.91 3.00 2.39 1.95 1.62 1.37 1.18 1.02 0.90 0.79 0.66 0.54 0.45 0.38 0.33 0.28
L/250 5.34 3.91 3.00 2.39 1.95 1.62 1.37 1.18 1.02 0.81 0.65 0.53 0.44 0.36 0.31 0.26 0.22
0.45
SLU 6.13 4.47 3.42 2.71 2.20 1.83 1.54 1.32 1.15 1.00 0.88 0.79 0.70 0.63 0.57 0.52 0.48
L/150 6.13 4.47 3.42 2.71 2.20 1.83 1.54 1.32 1.15 1.00 0.88 0.79 0.70 0.63 0.55 0.47 0.40
L/200 6.13 4.47 3.42 2.71 2.20 1.83 1.54 1.32 1.15 1.00 0.88 0.72 0.59 0.49 0.42 0.35 0.30
L/250 6.13 4.47 3.42 2.71 2.20 1.83 1.54 1.32 1.12 0.88 0.71 0.57 0.47 0.39 0.33 0.28 0.24
0.50
SLU 6.91 5.01 3.82 3.02 2.45 2.03 1.71 1.46 1.26 1.10 0.97 0.86 0.77 0.70 0.63 0.57 0.52
L/150 6.91 5.01 3.82 3.02 2.45 2.03 1.71 1.46 1.26 1.10 0.97 0.86 0.77 0.70 0.60 0.51 0.44
L/200 6.91 5.01 3.82 3.02 2.45 2.03 1.71 1.46 1.26 1.10 0.95 0.78 0.64 0.53 0.45 0.38 0.33
L/250 6.91 5.01 3.82 3.02 2.45 2.03 1.71 1.46 1.21 0.95 0.76 0.62 0.51 0.43 0.36 0.31 0.26
0.60
SLU 8.41 6.06 4.60 3.61 2.92 2.41 2.03 1.73 1.49 1.30 1.14 1.02 0.91 0.81 0.74 0.67 0.61
L/150 8.41 6.06 4.60 3.61 2.92 2.41 2.03 1.73 1.49 1.30 1.14 1.02 0.91 0.81 0.69 0.58 0.50
L/200 8.41 6.06 4.60 3.61 2.92 2.41 2.03 1.73 1.49 1.30 1.09 0.89 0.73 0.61 0.52 0.44 0.38
L/250 8.41 6.06 4.60 3.61 2.92 2.41 2.03 1.73 1.39 1.09 0.88 0.71 0.59 0.49 0.41 0.35 0.30
0.75
SLU 10.85 7.77 5.86 4.58 3.69 3.04 2.54 2.16 1.86 1.62 1.42 1.26 1.12 1.01 0.91 0.82 0.74
L/150 10.85 7.77 5.86 4.58 3.69 3.04 2.54 2.16 1.86 1.62 1.42 1.26 1.12 0.97 0.82 0.69 0.59
L/200 10.85 7.77 5.86 4.58 3.69 3.04 2.54 2.16 1.86 1.62 1.30 1.06 0.87 0.73 0.61 0.52 0.45
L/250 10.85 7.77 5.86 4.58 3.69 3.04 2.54 2.14 1.65 1.30 1.04 0.85 0.70 0.58 0.49 0.42 0.36
ables containing loads determined according to EC3-1-3-2001Te calculation load for SLU must include thesafety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
1-15
7/21/2019 catalog Megaprofil 2013 (1).pdf
26/191
76.18.988 (SINUS)
ROOF AND WALLS PROFILES
APPLICAION
Exterior plate for double insulated wall or roof
Vertical or horizontal mounting of plates for the wall
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.25 | 0.40 | 0.50 | 0.60
Polyester-silicone 25 14 standard colours thickness 0.40 | 0.45 | 0.50 | 0.60 | 0.75 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHT MAX. BENDINGMOMENT
MAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT W
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.40 3.97 37.50 37.50 2.00 1.65 655.00
0.45 4.46 45.90 45.90 2.50 2.02 925.00
0.50 4.96 54.30 54.30 2.90 2.39 1149.00
0.60 5.45 67.50 67.50 3.60 2.97 2105.00
0.75 7.14 72.90 72.90 3.90 3.21 2750.00
1-16
7/21/2019 catalog Megaprofil 2013 (1).pdf
27/191
ROOF AND WALLS PROFILES
76.18.988 (SINUS)
TABLE OF USED SPANS (M)
ADMITTEDLOAD
THICKNESS PURLIN DISTANCE
kg/m mmF/150 F/200 F/250 F/300 F/150 F/200 F/250 F/300 F/150 F/200 F/250 F/300
60
0.40 1.60 1.40 1.25 1.15 2.20 1.95 1.80 1.90 1.90 1.70 1.85 1.55
0.45 1.65 1.45 1.33 1.23 2.25 2.03 1.88 1.95 2.05 1.85 1.93 1.63
0.50 1.70 1.50 1.40 1.30 2.30 2.10 1.95 2.00 2.20 2.00 2.00 1.70
0.60 1.80 1.60 1.55 1.45 2.40 2.25 2.10 2.10 2.50 2.30 2.15 1.85
0.75 1.90 1.70 1.65 1.55 2.50 2.35 2.20 2.20 2.45 2.45 2.25 1.95
80
0.40 1.35 1.30 1.20 1.20 1.95 1.75 1.60 1.50 1.85 1.65 1.50 1.40
0.45 1.43 1.35 1.25 1.23 2.03 1.83 1.68 1.58 1.93 1.73 1.58 1.48
0.50 1.50 1.40 1.30 1.25 2.10 1.90 1.75 1.65 2.00 1.80 1.65 1.55
0.60 1.65 1.50 1.40 1.30 2.25 2.05 1.90 1.80 2.15 1.95 1.80 1.70
0.75 1.75 1.60 1.50 1.40 2.35 2.15 2.00 1.90 2.25 2.05 1.90 1.80
100
0.40 1.35 1.20 1.10 1.05 1.80 1.60 1.55 1.45 1.75 1.50 1.45 1.35
0.45 1.40 1.25 1.15 1.10 1.88 1.68 1.60 1.50 1.80 1.58 1.50 1.40
0.50 1.45 1.30 1.20 1.15 1.95 1.75 1.65 1.55 1.85 1.65 1.55 1.45
0.60 1.55 1.40 1.30 1.25 2.10 1.90 1.75 1.65 1.95 1.80 1.65 1.55
0.75 1.65 1.50 1.40 1.35 2.20 2.00 1.85 1.75 2.05 1.90 1.75 1.65
120
0.40 1.25 1.20 1.05 1.00 1.65 1.50 1.45 1.45 1.55 1.40 1.35 1.25
0.45 1.30 1.23 1.10 1.03 1.73 1.58 1.50 1.50 1.63 1.48 1.40 1.30
0.50 1.35 1.25 1.15 1.05 1.80 1.65 1.55 1.55 1.70 1.55 1.45 1.35
0.60 1.45 1.30 1.25 1.10 1.95 1.80 1.65 1.65 1.85 1.70 1.55 1.45
0.75 1.55 1.42 1.35 1.25 2.05 1.90 1.75 1.75 1.95 1.75 1.65 1.55
150
0.40 1.15 1.05 0.95 0.95 1.60 1.45 1.25 1.25 1.50 1.35 1.25 1.15
0.45 1.20 1.10 1.00 0.98 1.65 1.50 1.33 1.30 1.55 1.40 1.30 1.20
0.50 1.25 1.15 1.05 1.00 1.70 1.55 1.40 1.35 1.60 1.45 1.35 1.25
0.60 1.35 1.25 1.15 1.05 1.80 1.65 1.55 1.45 1.70 1.55 1.45 1.35
0.75 1.45 1.35 1.25 1.15 1.90 1.75 1.65 1.55 1.80 1.65 1.55 1.45
170
0.40 1.10 0.80 0.90 0.85 1.45 1.30 1.25 1.20 1.45 1.30 1.20 1.10
0.45 1.15 0.90 0.95 0.90 1.53 1.38 1.30 1.25 1.50 1.35 1.25 1.15
0.50 1.20 1.00 1.00 0.95 1.60 1.45 1.35 1.30 1.55 1.40 1.30 1.20
0.60 1.30 1.20 1.10 1.05 1.75 1.60 1.45 1.40 1.65 1.50 1.40 1.30
0.75 1.35 1.25 1.15 1.10 1.80 1.65 1.50 1.45 1.70 1.55 1.45 1.35
200
0.40 1.00 0.90 0.80 0.75 1.40 1.25 1.15 1.10 1.35 1.20 1.10 1.00
0.45 1.05 0.95 0.85 0.80 1.45 1.30 1.20 1.15 1.40 1.25 1.15 1.05
0.50 1.10 1.00 0.90 0.85 1.50 1.35 1.25 1.20 1.45 1.30 1.20 1.10
0.60 1.20 1.10 1.00 0.95 1.60 1.45 1.35 1.30 1.55 1.40 1.30 1.20
0.75 1.30 1.20 1.10 1.05 1.70 1.55 1.45 1.40 1.65 1.50 1.40 1.30
1-17
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
28/191
OPIC PROFILES
ROOF AND WALLS PROFILES
APPLICAION
Profiles for doors and gates
PRODUC FEAURES
Length Standard length of 1 m up to max. 8 mMetal Steel sheet S 250 GD
Finishing Polyester and plastisol according to the colour palette
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.25 | 0.40 | 0.50 | 0.60
Polyester-silicone 25 14 standard colours thickness 0.40 | 0.45 | 0.50 | 0.60 | 0.75 mm
1-18
7/21/2019 catalog Megaprofil 2013 (1).pdf
29/191
ROOF AND WALLS PROFILES
PLANK PROFILES
APPLICAION
Exterior plating for vertical facades
Vertical or horizontal mounting
PRODUC FEAURES
Length Standard length of up to max. 10 m
Metal Steel sheet S 250 GD
Finishing Polyester, available in a wide range of colours
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Walls made of double layer (support) panelsHorizontal or vertical positionThe width of the plank profile is 300 mmThe width of the joint is 20 mm
Minimum length: 0.5 m, maximum length: 6 m
For the range of colours, please contact ourSales Department.
Minimum length: 0.50 m max. length: 6 m
INVISIBLE FASENING WIH OPEN JOINS
1-19
7/21/2019 catalog Megaprofil 2013 (1).pdf
30/191
PLANK PROFILES
ROOF AND WALLS PROFILES
MOUNING
FINISHING PROFILES, CUSOMIZED FOLDING
Examples:
Dropping vessel Vertical joint Angle bracket
1-20
7/21/2019 catalog Megaprofil 2013 (1).pdf
31/191
TECHNICAL PROFILE
DECK 115.600
APPLICAION
Interior plate from insulated panels with double layer for walls
The interior deck is made up of a horizontal combination of purlins and filled with insulating material, supporting the exterior plate
PRODUC FEAURES
Length Standard lengths between 1.5 m and 12.5 m
Metal Steel sheet S 280 GD
Finishing Polyester according to the colour range at page 12
Accessories Finishing profiles, strips for thermal bridge breakthrough, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g zinc/m2 thickness 0.75 | 0.88 | 1.0 mm
Polyester-interior 15 m RAL 2002 thickness 0.75 | 0.88 | 1.0 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT IW
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.75 9.09 287.00 328.70 85.20 11.30 1680
0.88 10.65 384.00 439.30 111.00 15.10 2240
1.00 12.09 476.00 544.00 135.20 18.70 2810
2-1
7/21/2019 catalog Megaprofil 2013 (1).pdf
32/191
TABLE OF USED SPANS (M)
ADMITTEDLOAD
THICKNESS PURLIN DISTANCE
kg/m mmF/150 F/200 F/250 F/300 F/150 F/200 F/250 F/300 F/150 F/200 F/250 F/300
60
0.75 5.34 4.61 4.51 4.24 5.41 5.41 5.41 5.41 6.04 5.70 5.32 5.00
0.88 5.84 5.04 4.92 4.63 6.25 6.25 6.25 6.24 6.88 6.30 5.81 5.46
1.00 6.23 5.38 4.78 4.95 6.95 6.95 6.95 6.66 7.35 6.70 6.20 5.83
70
0.75 5.00 4.61 4.28 4.03 5.00 5.00 5.00 5.00 5.60 5.40 5.05 4.75
0.88 5.55 5.04 4.68 4.40 5.79 5.79 5.79 5.79 6.47 5.90 5.51 5.19
1.00 5.92 5.38 4.78 4.70 6.44 6.44 6.44 6.33 6.98 6.30 5.89 5.54
80
0.75 4.68 4.61 4.10 3.85 4.68 4.68 4.68 4.68 5.23 5.20 4.83 4.54
0.88 5.30 5.04 4.47 4.21 5.41 5.41 5.41 5.41 6.05 5.70 5.27 4.96
1.00 5.66 5.38 4.78 4.50 6.02 6.02 6.02 6.02 6.68 6.10 5.63 5.30
90
0.75 4.41 4.41 3.94 3.71 4.41 4.41 4.41 4.41 4.93 4.90 4.64 4.37
0.88 5.10 5.04 4.30 4.05 5.10 5.10 5.10 5.10 5.70 5.50 5.07 4.77
1.00 5.45 5.38 4.78 4.32 5.68 5.68 5.68 5.68 6.35 5.80 5.42 5.10
100
0.75 4.19 4.19 3.80 3.58 4.19 4.19 4.19 4.19 4.68 4.70 4.48 4.22
0.88 4.84 4.84 4.15 3.91 4.84 4.84 4.84 4.84 5.41 5.30 4.90 4.61
1.00 5.26 5.38 4.78 4.17 5.39 5.39 5.39 5.39 6.02 5.60 5.23 4.92
120
0.75 3.82 3.82 3.58 3.37 3.82 3.82 3.82 3.82 4.27 4.30 4.22 3.97
0.88 4.42 4.42 3.91 3.68 4.42 4.42 4.42 4.42 4.94 4.90 4.61 4.34
1.00 4.92 4.92 4.78 3.93 4.92 4.92 4.92 4.92 5.50 5.30 4.92 4.63
150
0.75 3.42 3.42 3.32 3.13 3.42 3.42 3.42 3.42 3.82 3.80 3.82 3.69
0.88 3.95 3.95 3.63 3.41 3.95 3.95 3.95 3.95 4/42 4.40 4.28 4.03
1.00 4.40 4.40 4.40 3.65 4.40 4.40 4.40 4/40 4.92 4.90 4.57 4.30
200
0.75 2.96 2.96 2.96 2.84 2.96 2.96 2.96 2.96 3.31 3.30 3.31 3.31
0.88 3.42 3.42 3.30 3.10 3.42 3.42 3.42 3.42 3.83 3.80 3.83 3.66
1.00 3.81 3.81 3.81 3.31 3.81 3.81 3.81 3.81 4.26 4.30 4.15 3.91
DECK 115.600
TECHNICAL PROFILE
2-2
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
33/191
TECHNICAL PROFILE
DECK 125.600
APPLICAION
Interior plate from insulated panels with double layer for walls
The interior deck is made up of a horizontal combination of purlins and filled with insulating material, supporting the exterior plate
PRODUC FEAURES
Length Standard lengths between 1.5 m and 12.5 m
Metal Steel sheet S 280 GD
Finishing Polyester according to the colour range at page 12
Accessories Finishing profiles, strips for thermal bridge breakthrough, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g/m2 thickness 0.75 | 0.88 | 1.0 mm
Polyester-interior 15 m RAL 9002 thickness 0.75 | 0.88 | 1.0 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT IW
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.75 9.45 242.00 297.00 85.20 11.30 1680.00
0.88 11.08 323.00 351.00 111.00 15.10 2240.00
1.00 12.57 400.00 399.00 135.20 18.70 2810.00
2-3
7/21/2019 catalog Megaprofil 2013 (1).pdf
34/191
TABLE OF USED SPANS (M)
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 1.15 1.04 0.93 0.85 0.77 0.71 0.65 0.57 0.51 0.45 0.41 0.37 0.33 0.3 0.27 0.25 0.23 0.21 0.19 0.18 0.16 0.15 0.14
L/200 1.15 0.98 0.84 0.72 0.63 0.55 0.49 0.43 0.38 0.34 0.31 0.28 0.25 0.23 0.2 0.19 0.17 0.16 0.14 0.13 0.12 0.11 0.1
L/300 0.77 0.65 0.56 0.48 0.42 0.37 0.32 0.29 0.25 0.23 0.2 0.18 0.17 0.15 0.14 0.12 0.11 0.1 0.1 0.09 0.08 0.08 0.07
0.88 11
L/150 1.48 1.33 1.2 1.09 0.99 0.88 0.78 0.69 0.61 0.55 0.49 0.44 0.4 0.36 0.33 0.3 0.27 0.25 0.23 0.21 0.2 0.18 0.17
L/200 1.38 1.17 1.01 0.87 0.76 0.66 0.58 0.52 0.46 0.41 0.37 0.33 0.3 0.27 0.25 0.22 0.2 0.19 0.17 0.16 0.15 0.14 0.13
L/300 0.92 0.78 0.67 0.58 0.5 0.44 0.39 0.34 0.31 0.27 0.24 0.22 0.2 0.18 0.16 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08
1 12.5
L/150 1.79 1.61 1.45 1.32 1.16 1.01 0.89 0.79 0.7 0.63 0.56 0.51 0.46 0.41 0.38 0.34 0.31 0.29 0.26 0.24 0.22 0.21 0.19
L/200 1.58 1.35 1.15 1 0.87 0.76 0.67 0.59 0.53 0.47 0.42 0.38 0.34 0.31 0.28 0.26 0.24 0.22 0.2 0.18 0.17 0.16 0.14
L/300 1.06 0.9 0.77 0.67 0.58 0.51 0.45 0.39 0.35 0.31 0.28 0.25 0.23 0.21 0.19 0.17 0.16 0.14 0.13 0.12 0.11 0.1 0.1
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 1.17 1.05 0.95 0.86 0.78 0.72 0.66 0.61 0.56 0.52 0.48 0.45 0.42 0.39 0.37 0.35 0.33 0.31 0.29 0.28 0.26 0.25 0.24
L/200 1.17 1.05 0.95 0.86 0.78 0.72 0.66 0.61 0.56 0.52 0.48 0.45 0.42 0.39 0.37 0.35 0.33 0.31 0.29 0.28 0.26 0.25 0.24
L/300 1.17 1.05 0.95 0.86 0.78 0.72 0.66 0.61 0.56 0.52 0.48 0.44 0.4 0.36 0.33 0.3 0.27 0.25 0.23 0.21 0.2 0.18 0.17
0.88 11
L/150 1.64 1.47 1.33 1.2 1.1 1 0.92 0.85 0.79 0.73 0.68 0.63 0.59 0.55 0.52 0.49 0.46 0.43 0.41 0.39 0.37 0.35 0.33
L/200 1.64 1.47 1.33 1.2 1.1 1 0.92 0.85 0.79 0.73 0.68 0.63 0.59 0.55 0.52 0.49 0.46 0.43 0.41 0.38 0.35 0.33 0.3
L/300 1.64 1.47 1.33 1.2 1.1 1 0.92 0.83 0.74 0.66 0.59 0.53 0.48 0.43 0.39 0.36 0.33 0.3 0.28 0.26 0.24 0.22 0.2
1 12.5L/150 2.07 1.86 1.68 1.52 1.39 1.27 1.17 1.07 0.99 0.92 0.86 0.8 0.75 0.7 0.66 0.62 0.58 0.55 0.52 0.49 0.47 0.44 0.42L/200 2.07 1.86 1.68 1.52 1.39 1.27 1.17 1.07 0.99 0.92 0.86 0.8 0.75 0.7 0.66 0.62 0.57 0.52 0.48 0.44 0.41 0.38 0.35
L/300 2.07 1.86 1.68 1.52 1.36 1.22 1.07 0.95 0.84 0.75 0.68 0.61 0.55 0.5 0.45 0.41 0.38 0.35 0.32 0.29 0.27 0.25 0.23
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 1.46 1.31 1.19 1.08 0.98 0.9 0.82 0.76 0.7 0.65 0.6 0.56 0.53 0.49 0.46 0.44 0.41 0.39 0.36 0.33 0.31 0.28 0.26
L/200 1.46 1.31 1.19 1.08 0.98 0.9 0.82 0.76 0.7 0.64 0.58 0.52 0.47 0.43 0.39 0.35 0.32 0.3 0.27 0.25 0.23 0.21 0.2
L/300 1.45 1.23 1.06 0.91 0.79 0.69 0.61 0.54 0.48 0.43 0.38 0.35 0.31 0.28 0.26 0.23 0.21 0.2 0.18 0.17 0.15 0.14 0.13
0.88 11
L/150 20.5 1.84 1.66 1.51 1.37 1.26 1.15 1.06 0.98 0.91 0.85 0.79 0.74 0.68 0.62 0.56 0.52 0.47 0.43 0.4 0.37 0.34 0.32
L/200 2.05 1.84 1.66 1.51 1.37 1.25 1.1 0.97 0.86 0.77 0.69 0.62 0.56 0.51 0.46 0.42 0.39 0.35 0.33 0.3 0.28 0.26 0.24
L/300 1.74 1.48 1.27 1.09 0.95 0.83 0.73 0.55 0.58 0.51 0.46 0.42 0.38 0.34 0.31 0.28 0.26 0.24 0.22 0.2 0.18 0.17 0.16
1 12.5
L/150 2.59 2.33 2.1 1.9 1.74 1.59 1.46 1.34 1.24 1.15 1.06 0.95 0.86 0.78 0.71 0.65 0.59 0.54 0.5 0.46 0.42 0.39 0.36
L/200 2.59 2.33 2.1 1.88 1.64 1.43 1.26 1.12 0.99 0.89 0.79 0.72 0.65 0.59 0.53 0.49 0.44 0.41 0.37 0.34 0.32 0.29 0.27
L/300 1.99 1.7 1.45 1.26 1.09 0.96 0.84 0.74 0.66 0.59 0.53 0.48 0.43 0.39 0.35 0.32 0.3 0.27 0.25 0.23 0.21 0.2 0.18
Suction
DECK 125.600
TECHNICAL PROFILE
2-4
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
35/191
Pressure
TABLE OF USED SPANS (M)
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 0.96 0.86 0.78 0.71 0.64 0.59 0.54 0.50 0.46 0.43 0.40 0.37 0.35 0.32 0.30 0.29 0.27 0.25 0.24 0.23 0.22 0.21 0.20
L/200 0.96 0.86 0.78 0.71 0.64 0.59 0.54 0.50 0.46 0.43 0.40 0.37 0.35 0.32 0.30 0.29 0.27 0.25 0.24 0.22 0.20 0.19 0.17
L/300 0.96 0.86 0.78 0.71 0.64 0.59 0.54 0.48 0.42 0.38 0.34 0.31 0.28 0.25 0.23 0.21 0.19 0.17 0.16 0.15 0.14 0.13 0.12
0.88 11
L/150 1.40 1.26 1.13 1.03 0.94 0.86 0.79 0.73 0.67 0.62 0.58 0.54 0.50 0.47 0.44 0.42 0.39 0.37 0.35 0.33 0.31 0.29 0.27
L/200 1.40 1.26 1.13 1.03 0.94 0.86 0.79 0.73 0.67 0.62 0.58 0.53 0.48 0.43 0.40 0.36 0.33 0.30 0.28 0.26 0.24 0.22 0.20
L/300 1.40 1.26 1.08 0.93 0.81 0.71 0.62 0.55 0.49 0.44 0.39 0.35 0.32 0.29 0.26 0.24 0.22 0.20 0.19 0.17 0.16 0.15 0.13
1 12.5
L/150 1.81 1.62 1.46 1.33 1.21 1.11 1.02 0.94 0.87 0.80 0.75 0.70 0.65 0.61 0.57 0.54 0.50 0.46 0.42 0.39 0.36 0.33 0.31
L/200 1.81 1.62 1.46 1.33 1.21 1.11 1.02 0.94 0.84 0.75 0.67 0.61 0.55 0.50 0.45 0.41 0.38 0.34 0.32 0.29 0.27 0.25 0.23
L/300 1.69 1.43 1.23 1.06 0.92 0.81 0.71 0.63 0.56 0.50 0.45 0.40 0.36 0.33 0.30 0.27 0.25 0.23 0.21 0.19 0.18 0.17 0.15
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 1.00 0.90 0.81 0.73 0.67 0.61 0.56 0.52 0.48 0.44 0.41 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.25 0.24 0.22 0.21 0.20
L/200 1.00 0.90 0.81 0.73 0.67 0.61 0.56 0.52 0.48 0.44 0.41 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.25 0.24 0.22 0.21 0.20
L/300 1.00 0.90 0.81 0.73 0.67 0.61 0.56 0.52 0.48 0.44 0.41 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.25 0.24 0.22 0.21 0.20
0.88 11
L/150 1.44 1.32 1.19 1.08 0.98 0.90 0.83 0.76 0.70 0.65 0.61 0.57 0.53 0.49 0.46 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
L/200 1.44 1.32 1.19 1.08 0.98 0.90 0.83 0.76 0.70 0.65 0.61 0.57 0.53 0.49 0.46 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
L/300 1.44 1.32 1.19 1.08 0.98 0.90 0.83 0.76 0.70 0.65 0.61 0.57 0.53 0.49 0.46 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
1 12.5L/150 1.82 1.67 1.54 1.40 1.27 1.16 1.07 0.99 0.91 0.84 0.79 0.73 0.68 0.64 0.60 0.57 0.53 0.50 0.48 0.45 0.43 0.40 0.38L/200 1.82 1.67 1.54 1.40 1.27 1.16 1.07 0.99 0.91 0.84 0.79 0.73 0.68 0.64 0.60 0.57 0.53 0.50 0.48 0.45 0.43 0.40 0.38
L/300 1.82 1.67 1.54 1.40 1.27 1.16 1.07 0.99 0.91 0.84 0.79 0.73 0.68 0.64 0.60 0.57 0.53 0.50 0.48 0.45 0.43 0.40 0.37
THICKNESS GF
MAXADMITTED DISTANCES L [M] DEPENDING ON ALLOWED Q LOADS [KN/M2]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 94.0 9.25 9.50 9.75 10.00
0.75 9.4
L/150 1.24 1.12 1.01 0.92 0.84 0.76 0.70 0.65 0.60 0.55 0.52 0.48 0.45 0.42 0.39 0.37 0.35 0.33 0.31 0.30 0.28 0.27 0.25
L/200 1.24 1.12 1.01 0.92 0.84 0.76 0.70 0.65 0.60 0.55 0.52 0.48 0.45 0.42 0.39 0.37 0.35 0.33 0.31 0.30 0.28 0.27 0.25
L/300 1.24 1.12 1.01 0.92 0.84 0.76 0.70 0.65 0.60 0.55 0.52 0.48 0.45 0.42 0.39 0.37 0.35 0.33 0.31 0.28 0.26 0.24 0.22
0.88 11
L/150 1.72 1.59 1.47 1.35 1.23 1.12 1.03 0.95 0.88 0.82 0.76 0.71 0.66 0.62 0.58 0.55 0.51 0.49 0.46 0.43 0.41 0.39 0.37
L/200 1.72 1.59 1.47 1.35 1.23 1.12 1.03 0.95 0.88 0.82 0.76 0.71 0.66 0.62 0.58 0.55 0.51 0.49 0.46 0.43 0.41 0.39 0.37
L/300 1.72 1.59 1.47 1.35 1.23 1.12 1.03 0.95 0.88 0.82 0.74 0.67 0.60 0.55 0.50 0.45 0.41 0.38 0.35 0.42 0.30 0.27 0.25
1 12.5
L/150 2.17 2.00 1.85 1.71 1.59 1.46 1.34 1.23 1.14 1.06 0.98 0.92 0.86 0.80 0.75 0.71 0.67 0.63 0.59 0.56 0.53 0.75 0.71
L/200 2.17 2.00 1.85 1.71 1.59 1.46 1.34 1.23 1.14 1.06 0.98 0.92 0.86 0.80 0.75 0.71 0.67 0.63 0.59 0.55 0.51 0.59 0.55
L/300 2.17 2.00 1.85 1.71 1.59 1.46 1.34 1.19 1.06 0.94 0.85 0.76 0.69 0.62 0.57 0.52 0.47 0.43 0.40 0.37 0.34 0.40 0.37
TECHNICAL PROFILE
DECK 125.600
2-5
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
36/191
DECK 160.600
TECHNICAL PROFILE
APPLICAION
Interior plate from insulated panels with double layer for walls
The interior deck is made up of a horizontal combination of purlins and it is filled with insulating material, supporting the plate
PRODUC FEAURES
Length Standard lengths between 1.5 m and 12.5 m
Metal Steel sheet S 280 GD
Finishing Polyester according to the colour range at page 13
Accessories Finishing profiles, strips for thermal bridge breakthrough, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g/m2 thickness 0.75 | 0.88 | 1.0 mm
Polyester-interior 15 m RAL 9002 thickness 0.75 | 0.88 | 1.0 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHT MAX. BENDINGMOMENT
MAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT IW
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.75 10.10 389.40 389.40 133.90 15.30 1680
0.88 11.83 450.50 450.50 148.60 17.70 2240
1.00 13.43 511.60 511.60 175.10 20.10 2810
2-6
7/21/2019 catalog Megaprofil 2013 (1).pdf
37/191
TECHNICAL PROFILE
DECK 160.600
ONE SPAN
THICKNESS G F MAX ADMITTED Q LOADS [KN.M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 9.00 9.25 9.50 9.75 10.00
0.75 10.10
SLU 1.00 0.95 0.90 0.82 0.75 0.69 0.63 0.58 0.54 0.50 0.46 0.43 0.40 0.38 0.35 0.33 0.31 0.30 0.28 0.27 0.25 0.24 0.23
L.150 1.00 0.95 0.90 0.82 0.75 0.69 0.63 0.58 0.54 0.50 0.46 0.43 0.40 0.38 0.35 0.33 0.31 0.30 0.28 0.27 0.25 0.24 0.23
L.200 1.00 0.95 0.90 0.82 0.75 0.69 0.63 0.58 0.54 0.50 0.46 0.43 0.40 0.38 0.35 0.33 0.31 0.30 0.28 0.27 0.25 0.24 0.23
L.300 1.00 0.95 0.90 0.82 0.75 0.69 0.63 0.58 0.54 0.50 0.46 0.43 0.40 0.38 0.35 0.33 0.31 0.30 0.28 0.27 0.25 0.24 0.22
0.88 11.83
SLU 1.53 1.45 1.35 1.22 1.11 1.02 0.94 0.86 0.80 0.74 0.69 0.64 0.60 0.56 0.53 0.50 0.47 0.44 0.42 0.39 0.37 0.35 0.34
L.150 1.53 1.45 1.35 1.22 1.11 1.02 0.94 0.86 0.80 0.74 0.69 0.64 0.60 0.56 0.53 0.50 0.47 0.44 0.42 0.39 0.37 0.35 0.34
L.200 1.53 1.45 1.35 1.22 1.11 1.02 0.94 0.86 0.80 0.74 0.69 0.64 0.60 0.56 0.53 0.50 0.47 0.44 0.42 0.39 0.37 0.35 0.34
L.300 1.53 1.45 1.35 1.22 1.11 1.02 0.94 0.86 0.80 0.74 0.69 0.64 0.60 0.56 0.51 0.47 0.43 0.39 0.36 0.33 0.31 0.28 0.26
1.00 13.43
SLU 2.01 1.90 1.75 1.59 1.45 1.32 1.22 1.12 1.04 0.96 0.89 0.83 0.78 0.73 0.68 0.64 0.61 0.57 0.54 0.51 0.49 0.46 0.44
L.150 2.01 1.90 1.75 1.59 1.45 1.32 1.22 1.12 1.04 0.96 0.89 0.83 0.78 0.73 0.68 0.64 0.61 0.57 0.54 0.51 0.49 0.46 0.44
L.200 2.01 1.90 1.75 1.59 1.45 1.32 1.22 1.12 1.04 0.96 0.89 0.83 0.78 0.73 0.68 0.64 0.61 0.57 0.54 0.51 0.49 0.46 0.44
L.300 2.01 1.90 1.75 1.59 1.45 1.32 1.22 1.12 1.04 0.96 0.87 0.79 0.71 0.64 0.59 0.53 0.49 0.45 0.41 0.38 0.35 0.32 0.30
WO SPANS
THICKNESS G F MAX ADMITTED Q LOADS [KN.M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 9.00 9.25 9.50 9.75 10.00
0.75 10.10
SLU 1.13 1.05 0.97 0.91 0.84 0.79 0.74 0.70 0.65 0.62 0.58 0.55 0.52 0.49 0.47 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
L.150 1.13 1.05 0.97 0.91 0.84 0.79 0.74 0.70 0.65 0.62 0.58 0.55 0.52 0.49 0.47 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
L.200 1.13 1.05 0.97 0.91 0.84 0.79 0.74 0.70 0.65 0.62 0.58 0.55 0.52 0.49 0.47 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
L.300 1.13 1.05 0.97 0.91 0.84 0.79 0.74 0.70 0.65 0.62 0.58 0.55 0.52 0.49 0.47 0.44 0.41 0.39 0.37 0.35 0.33 0.31 0.30
0.88 11.83
SLU 1.56 1.44 1.33 1.23 1.15 1.07 1.00 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.62 0.58 0.55 0.52 0.49 0.46 0.44 0.42 0.40
L.150 1.56 1.44 1.33 1.23 1.15 1.07 1.00 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.62 0.58 0.55 0.52 0.49 0.46 0.44 0.42 0.40
L.200 1.56 1.44 1.33 1.23 1.15 1.07 1.00 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.62 0.58 0.55 0.52 0.49 0.46 0.44 0.42 0.40
L.300 1.56 1.44 1.33 1.23 1.15 1.07 1.00 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.62 0.58 0.55 0.52 0.49 0.46 0.44 0.42 0.40
1.00 13.43
SLU 1.94 1.79 1.65 1.53 1.42 1.33 1.24 1.16 1.09 1.02 0.96 0.91 0.86 0.81 0.77 0.72 0.68 0.64 0.60 0.57 0.54 0.52 0.49
L.150 1.94 1.79 1.65 1.53 1.42 1.33 1.24 1.16 1.09 1.02 0.96 0.91 0.86 0.81 0.77 0.72 0.68 0.64 0.60 0.57 0.54 0.52 0.49
L.200 1.94 1.79 1.65 1.53 M2 1.33 1.24 1.16 1.09 1.02 0.96 0.91 0.86 0.81 0.77 0.72 0.68 0.64 0.60 0.57 0.54 0.52 0.49
L.300 1.94 1.79 1.65 1.53 1.42 1.33 1.24 1.16 1.09 1.02 0.96 0.91 0.86 0.81 0.77 0.72 0.68 0.64 0.60 0.57 0.54 0.52 0.49
HREE SPANS
THICKNESS G F MAX ADMITTED Q LOADS [KN.M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00 8.25 8.50 8.75 9.00 9.25 9.50 9.75 10.00
0.75 10.10
SLU 1.26 1.19 1.13 1.08 1.01 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.63 0.59 0.55 0.52 0.49 0.46 0.44 0.41 0.39 0.37 0.35
L.150 1.26 1.19 1.13 1.08 1.01 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.63 0.59 0.55 0.52 0.49 0.46 0.44 0.41 0.39 0.37 0.35
L.200 1.26 1.19 1.13 1.08 1.01 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.63 0.59 0.55 0.52 0.49 0.46 0.44 0.41 0.39 0.37 0.35
L.300 1.26 1.19 1.13 1.08 1.01 0.94 0.88 0.83 0.78 0.74 0.70 0.66 0.63 0.59 0.55 0.52 0.49 0.46 0.44 0.41 0.39 0.37 0.35
0.88 11.83
SLU 1.85 1.71 1.58 1.47 1.37 1.28 1.20 1.13 1.06 1.00 0.94 0.89 0.84 0.80 0.76 0.72 0.68 0.65 0.61 0.58 0.55 0.52 0.49
L.150 1.85 1.71 1.58 1.47 1.37 1.28 1.20 1.13 1.06 1.00 0.94 0.89 0.84 0.80 0.76 0.72 0.68 0.65 0.61 0.58 0.55 0.52 0.49
L.200 1.85 1.71 1.58 1.47 1.37 1.28 1.20 1.13 1.06 1.00 0.94 0.89 0.84 0.80 0.76 0.72 0.68 0.65 0.61 0.58 0.55 0.52 0.49
L.300 1.85 1.71 1.58 1.47 1.37 1.28 1.20 1.13 1.06 1.00 0.94 0.89 0.84 0.80 0.76 0.72 0.68 0.65 0.61 0.58 0.55 0.52 0.49
1.00 13.43
SLU 2.31 2.13 1.97 1.83 1.71 1.59 1.49 1.40 1.31 1.24 1.17 1.10 1.04 0.99 0.93 0.89 0.84 0.80 0.76 0.72 0.68 0.64 0.61
L.150 2.31 2.13 1.97 1.83 1.71 1.59 1.49 1.40 1.31 1.24 1.17 1.10 1.04 0.99 0.93 0.89 0.84 0.80 0.76 0.72 0.68 0.64 0.61
L.200 2.31 2.13 1.97 1.83 1.71 1.59 1.49 1.40 1.31 1.24 1.17 1.10 1.04 0.99 0.93 0.89 0.84 0.80 0.76 0.72 0.68 0.64 0.61
L.300 2.31 2.13 1.97 1.83 1.71 1.59 1.49 1.40 1.31 1.24 1.17 1.10 1.04 0.99 0.93 0.89 0.84 0.80 0.76 0.72 0.66 0.61 0.57
2-7
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
38/191
APPLICAION
Independent lower plate for flat roofs (clear span 3-5 m)
PRODUC FEAURES
Length Standard lengths between 1.5 m and 12.5 m
Metal Steel sheet S 280 GD
Finishing Polyester according to the colour range at page 12
Accessories Finishing profiles, strips for thermal bridge breakthrough, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g/m2 thickness 0.75 | 0.88 | 1.0 mm
Polyester-interior 15 m RAL 9002 thickness 0.75 | 0.88 | 1.0 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT IW
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.75 7.96 430.00 430.00 77.45 16.90 2295.00
0.88 9.32 516.00 516.00 95.65 20.28 3032.00
1.00 10.58 595.00 595.00 112.50 23.41 3785.00
1.25 13.21 756.00 756.00 144.80 29.70 5574.00
85.280.1120
TECHNICAL PROFILE
2-8
7/21/2019 catalog Megaprofil 2013 (1).pdf
39/191
TECHNICAL PROFILE
85.280.1120
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00
0.75
SLU 3.82 3.26 2.81 2.45 2.15 1.90 1.70 1.52 1.38 1.25 1.14 1.04 0.96 0.88 0.81 0.76 0.70
L/200 2.31 1.82 1.46 1.18 0.98 0.81 0.69 0.58 0.50 0.43 0.38 0.33 0.29 0.26 0.23 0.20 0.18
L/250 1.85 1.46 1.17 0.95 0.78 0.65 0.55 0.47 0.40 0.35 0.30 0.26 0.23 0.20 0.18 0.16 0.15
L/300 1.54 1.21 0.97 0.79 0.65 0.54 0.46 0.39 0.33 0.29 0.25 0.22 0.19 0.17 0.15 0.14 0.12
0.88
SLU 4.59 3.91 3.37 2.94 2.58 2.29 2.04 1.83 1.65 1.50 1.36 1.25 1.15 1.06 0.98 0.91 0.84
L/200 2.86 2.25 1.80 1.46 1.21 1.00 0.85 0.72 0.62 0.53 0.46 0.41 0.36 0.32 0.28 0.25 0.22
L/250 2.29 1.80 1.44 1.17 0.96 0.80 0.68 0.58 0.49 0.43 0.37 0.32 0.29 0.25 0.22 0.20 0.18
L/300 1.90 1.50 1.20 0.98 0.80 0.67 0.56 0.48 0.41 0.36 0.31 0.27 0.24 0.21 0.19 0.17 0.15
1.00
SLU 5.29 4.51 3.89 3.38 2.98 2.64 2.35 2.11 1.90 1.73 1.57 1.44 1.32 1.22 1.13 1.04 0.97
L/200 3.36 2.64 2.12 1.72 1.42 1.18 1.00 0.85 0.73 0.63 0.55 0.48 0.42 0.37 0.33 0.29 0.26
L/250 2.69 2.11 1.69 1.38 1.13 0.95 0.80 0.68 0.58 0.50 0.44 0.38 0.34 0.30 0.26 0.24 0.21
L/300 2.24 1.76 1.41 1.15 0.95 0.79 0.66 0.56 0.48 0.42 0.36 0.32 0.28 0.25 0.22 0.20 0.18
1.25
SLU 6.72 5.73 4.94 4.30 3.78 3.35 2.99 2.68 2.42 2.19 2.00 1.83 1.68 1.55 1.43 1.33 1.23
L/200 4.32 3.40 2.72 2.21 1.82 1.52 1.28 1.09 0.93 0.81 0.70 0.61 0.54 0.48 0.43 0.38 0.34
L/250 3.46 2.72 2.18 1.77 1.46 1.22 1.03 0.87 0.75 0.65 0.56 0.49 0.43 0.38 0.34 0.30 0.27
L/300 2.88 2.27 1.82 1.48 1.22 1.01 0.85 0.73 0.62 0.54 0.47 0.41 0.36 0.32 0.28 0.25 0.23
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00
0.75
SLU 2.87 2.52 2.23 1.99 1.79 1.62 1.47 1.34 1.23 1.13 1.04 0.97 0.90 0.83 0.78 0.73 0.68L/200 2.87 2.52 2.23 1.99 1.79 1.62 1.47 1.34 1.22 1.05 0.92 0.80 0.71 0.62 0.55 0.50 0.44
L/250 2.87 2.52 2.23 1.99 1.79 1.59 1.34 1.14 0.97 0.84 0.73 0.64 0.56 0.50 0.44 0.40 0.36
L/300 2.87 2.52 2.23 1.93 1.59 1.32 1.11 0.95 0.81 0.70 0.61 0.53 0.47 0.42 0.37 0.33 0.30
0.88
SLU 3.57 3.13 2.77 2.47 2.22 2.00 1.82 1.65 1.51 1.39 1.28 1.19 1.10 1.02 0.95 0.89 0.84
L/200 3.57 3.13 2.77 2.47 2.22 2.00 1.82 1.65 1.51 1.30 1.13 0.99 0.87 0.77 0.69 0.61 0.55
L/250 3.57 3.13 2.77 2.47 2.22 1.96 1.65 1.40 1.20 1.04 0.90 0.79 0.70 0.62 0.55 0.49 0.44
L/300 3.57 3.13 2.77 2.38 1.96 1.63 1.38 1.17 1.00 0.87 0.75 0.66 0.58 0.51 0.46 0.41 0.37
1.00
SLU 4.24 3.72 3.28 2.92 2.62 2.36 2.14 1.95 1.78 1.64 1.51 1.39 1.29 1.20 1.12 1.04 0.97
L/200 4.24 3.72 3.28 2.92 2.62 2.36 2.14 1.95 1.77 1.53 1.33 1.16 1.02 0.91 0.81 0.72 0.65
L/250 4.24 3.72 3.28 2.92 2.62 2.31 1.94 1.65 1.42 1.22 1.06 0.93 0.82 0.73 0.64 0.58 0.52
L/300 4.24 3.72 3.28 2.80 2.30 1.92 1.62 1.38 1.18 1.02 0.89 0.78 0.68 0.60 0.54 0.48 0.43
1.25
SLU 5.67 4.95 4.37 3.88 3.47 3.12 2.83 2.57 2.35 2.15 1.98 1.83 1.68 1.55 1.43 1.33 1.23
L/200 5.67 4.95 4.37 3.88 3.47 3.12 2.83 2.57 2.28 1.97 1.71 1.50 1.32 1.17 1.04 0.93 0.83
L/250 5.67 4.95 4.37 3.88 3.47 2.97 2.50 2.13 1.82 1.57 1.37 1.20 1.05 0.93 0.83 0.74 0.66
L/300 5.67 4.95 4.37 3.60 2.97 2.47 2.08 1.77 1.52 1.31 1.14 1.00 0.88 0.78 0.69 0.62 0.55
2-9
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
40/191
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00
0.75
SLU 3.48 3.07 2.72 2.43 2.19 1.98 1.80 1.64 1.51 1.39 1.28 1.18 1.10 1.02 0.96 0.90 0.84
L/200 3.48 3.07 2.72 2.28 1.88 1.56 1.32 1.12 0.96 0.83 0.72 0.63 0.56 0.49 0.44 0.39 0.35
L/250 3.48 2.80 2.24 1.82 1.50 1.25 1.05 0.90 0.77 0.66 0.58 0.51 0.44 0.39 0.35 0.31 0.28
L/300 2.97 2.33 1.87 1.52 1.25 1.04 0.88 0.75 0.64 0.55 0.48 0.42 0.37 0.33 0.29 0.26 0.23
0.88
SLU 4.35 3.82 3.38 3.02 2.71 2.45 2.22 2.03 1.86 1.71 1.58 1.46 1.35 1.26 1.18 1.10 1.03
L/200 4.35 3.82 3.38 2.81 2.32 1.93 1.63 1.38 1.19 1.03 0.89 0.78 0.69 0.61 0.54 0.48 0.43
L/250 4.35 3.46 2.77 2.25 1.85 1.55 1.30 1.11 0.95 0.82 0.71 0.62 0.55 0.49 0.43 0.39 0.35
L/300 3.66 2.88 2.31 1.88 1.55 1.29 1.09 0.92 0.79 0.68 0.59 0.52 0.46 0.41 0.36 0.32 0.29
1.00
SLU 5.17 4.53 4.01 3.58 3.21 2.89 2.62 2.39 2.19 2.01 1.85 1.71 1.59 1.48 1.38 1.29 1.21
L/200 5.17 4.53 4.01 3.31 2.73 2.27 1.91 1.63 1.40 1.21 1.05 0.92 0.81 0.71 0.64 0.57 0.51
L/250 5.17 4.07 3.26 2.65 2.18 1.82 1.53 1.30 1.12 0.96 0.84 0.73 0.65 0.57 0.51 0.45 0.41
L/300 4.31 3.39 2.71 2.21 1.82 1.52 1.28 1.09 0.93 0.80 0.70 0.61 0.54 0.48 0.42 0.38 0.34
1.25
SLU 6.92 6.06 5.35 4.75 4.26 3.83 3.47 3.16 2.89 2.65 2.44 2.25 2.09 1.94 1.79 1.66 1.54
L/200 6.92 6.06 5.24 4.26 3.51 2.93 2.46 2.10 1.80 1.55 1.35 1.18 1.04 0.92 0.82 0.73 0.65
L/250 6.65 5.23 4.19 3.41 2.81 2.34 1.97 1.68 1.44 1.24 1.08 0.94 0.83 0.74 0.65 0.58 0.52
L/300 5.54 4.36 3.49 2.84 2.34 1.95 1.64 1.40 1.20 1.03 0.90 0.79 0.69 0.61 0.55 0.49 0.44
ables containing loads determined according to EC3-1-3-2001Te calculation load for SLU must include
the safety factorsFor SLS the safety factors = 1.0Continuous load [kN/m2]
85.280.1120
TECHNICAL PROFILE
2-10
7/21/2019 catalog Megaprofil 2013 (1).pdf
41/191
TECHNICAL PROFILE
135.310.930
APPLICAION
Independent lower plate for flat roofs (clear span 4-8 m)
PRODUC FEAURES
Length Standard lengths between 1.5 m and 15.5 mMetal Steel sheet S 280 GD
Finishing Polyester according to the colour range at page 12
Accessories Finishing profiles, sealing strips, see the chapter Accessories
STANDARD EXECUTION
Galva 140 g/m2 thickness 0.75 | 0.88 | 1.0 | 1.25 mm
Polyester-interior 15 m RAL 9002 thickness 0.75 | 0.88 | 1.0 | 1.25 mm
ECHNICAL SPECIFICAIONS
DEFAULTTHICKNESS
WEIGHTMAX. BENDING
MOMENTMAXIMUMMOMENT
MOMENT OFINERTIA I
RESISTANCEMOMENT IW
BEARINGREACTION
mm kg/m2 kg.m kg.m cm4 cm3 kg
0.75 9.58 822.00 822.00 267.00 32.33 2268
0.88 11.23 984.00 984.00 318.00 38.69 3300
1.00 12.74 1125.00 1125.00 363.00 44.21 4220
1.25 15.90 1417.00 1417.00 458.00 55.69 6430
2-11
7/21/2019 catalog Megaprofil 2013 (1).pdf
42/191
ONE SPAN
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00
0.75
SLU 4.11 3.64 3.25 2.91 2.63 2.39 2.17 1.99 1.83 1.68 1.56 1.44 1.34 1.25 1.17 1.09 1.03
L/200 3.36 2.80 2.36 2.01 1.72 1.49 1.29 1.13 1.00 0.88 0.78 0.70 0.63 0.56 0.51 0.46 0.42
L/250 2.69 2.24 1.89 1.61 1.38 1.19 1.04 0.91 0.80 0.71 0.63 0.56 0.50 0.45 0.41 0.37 0.34
L/300 2.24 1.87 1.58 1.34 1.15 0.99 0.86 0.76 0.66 0.59 0.52 0.47 0.42 0.38 0.34 0.31 0.28
0.88
SLU 4.92 4.36 3.89 3.49 3.15 2.86 2.60 2.38 2.19 2.02 1.86 1.73 1.61 1.50 1.40 1.31 1.23
L/200 4.01 3.34 2.81 2.39 2.05 1.77 1.54 1.35 1.19 1.05 0.93 0.83 0.75 0.67 0.61 0.55 0.50
L/250 3.21 2.67 2.25 1.91 1.64 1.42 1.23 1.08 0.95 0.84 0.75 0.67 0.60 0.54 0.49 0.44 0.40
L/300 2.67 2.23 1.88 1.60 1.37 1.18 1.03 0.90 0.79 0.70 0.62 0.56 0.50 0.45 0.41 0.37 0.33
1.00
SLU 5.63 4.98 4.44 3.99 3.60 3.27 2.98 2.72 2.50 2.30 2.13 1.98 1.84 1.71 1.60 1.50 1.41
L/200 4.57 3.81 3.21 2.73 2.34 2.02 1.76 1.54 1.36 1.20 1.07 0.95 0.85 0.77 0.69 0.63 0.57
L/250 3.66 3.05 2.57 2.19 1.87 1.62 1.41 1.23 1.08 0.96 0.85 0.76 0.68 0.61 0.56 0.50 0.46
L/300 3.05 2.54 2.14 1.82 1.56 1.35 1.17 1.03 0.90 0.80 0.71 0.63 0.57 0.51 0.46 0.42 0.38
1.25
SLU 7.09 6.28 5.60 5.02 4.53 4.11 3.75 3.43 3.15 2.90 2.68 2.49 2.31 2.16 2.02 1.89 1.77
L/200 5.77 4.81 4.05 3.45 2.95 2.55 2.22 1.94 1.71 1.51 1.34 1.20 1.08 0.97 0.88 0.79 0.72
L/250 4.62 3.85 3.24 2.76 2.36 2.04 1.78 1.55 1.37 1.21 1.08 0.96 0.86 0.78 0.70 0.63 0.58
L/300 3.85 3.21 2.70 2.30 1.97 1.70 1.48 1.30 1.14 1.01 0.90 0.80 0.72 0.65 0.58 0.53 0.48
WO SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00
0.75
SLU 2.61 2.38 2.18 2.01 1.85 1.72 1.60 1.49 1.39 1.30 1.22 1.15 1.08 1.02 0.96 0.91 0.87L/200 2.61 2.38 2.18 2.01 1.85 1.72 1.60 1.49 1.39 1.30 1.22 1.15 1.08 1.02 0.96 0.91 0.87
L/250 2.61 2.38 2.18 2.01 1.85 1.72 1.60 1.49 1.39 1.30 1.22 1.15 1.08 1.02 0.96 0.90 0.82
L/300 2.61 2.38 2.18 2.01 1.85 1.72 1.60 1.49 1.39 1.30 1.22 1.14 1.02 0.92 0.83 0.75 0.68
0.88
SLU 3.43 3.12 2.85 2.61 2.41 2.22 2.06 1.92 1.79 1.67 1.56 1.47 1.38 1.30 1.23 1.16 1.10
L/200 3.43 3.12 2.85 2.61 2.41 2.22 2.06 1.92 1.79 1.67 1.56 1.47 1.38 1.30 1.23 1.16 1.10
L/250 3.43 3.12 2.85 2.61 2.41 2.22 2.06 1.92 1.79 1.67 1.56 1.47 1.38 1.30 1.19 1.07 0.98
L/300 3.43 3.12 2.85 2.61 2.41 2.22 2.06 1.92 1.79 1.67 1.52 1.36 1.22 1.09 0.99 0.90 0.81
1.00
SLU 4.11 3.73 3.40 3.12 2.87 2.65 2.45 2.28 2.12 1.98 1.85 1.74 1.63 1.54 1.45 1.37 1.30
L/200 4.11 3.73 3.40 3.12 2.87 2.65 2.45 2.28 2.12 1.98 1.85 1.74 1.63 1.54 1.45 1.37 1.30
L/250 4.11 3.73 3.40 3.12 2.87 2.65 2.45 2.28 2.12 1.98 1.85 1.74 1.63 1.50 1.35 1.23 1.12
L/300 4.11 3.73 3.40 3.12 2.87 2.65 2.45 2.28 2.12 1.95 1.73 1.55 1.39 1.25 1.13 1.02 0.93
1.25
SLU 5.58 5.05 4.60 4.20 3.86 3.55 3.28 3.04 2.83 2.64 2.46 2.31 2.16 2.04 1.92 1.81 1.71
L/200 5.58 5.05 4.60 4.20 3.86 3.55 3.28 3.04 2.83 2.64 2.46 2.31 2.16 2.04 1.92 1.81 1.71
L/250 5.58 5.05 4.60 4.20 3.86 3.55 3.28 3.04 2.83 2.64 2.46 2.31 2.10 1.89 1.71 1.55 1.41
L/300 5.58 5.05 4.60 4.20 3.86 3.55 3.28 3.04 2.78 2.46 2.19 1.95 1.75 1.58 1.42 1.29 1.17
135.310.930
TECHNICAL PROFILE
2-12
MRRO011-0
7/21/2019 catalog Megaprofil 2013 (1).pdf
43/191
TECHNICAL PROFILE
135.310.930
THREE SPANS
THICKNESS F MAX ADMITTED Q LOADS [KN/M2] DEPENDING ON ALLOWED DISTANCES L[M]
4.00 4.25 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 7.00 7.25 7.50 7.75 8.00
0.75
SLU 3.15 2.88 2.64 2.43 2.25 2.08 1.94 1.81 1.69 1.58 1.49 1.40 1.32 1.24 1.18 1.11 1.06
L/200 3.15 2.88 2.64 2.43 2.25 2.08 1.94 1.81 1.69 1.58 1.49 1.35 1.21 1.09 0.98 0.89 0.81
L/250 3.15 2.88 2.64 2.43 2.25 2.08 1.94 1.74 1.53 1.36 1.21 1.08 0.97 0.87 0.79 0.71 0.65
L/300 3.15 2.88 2.64 2.43 2.21 1.91 1.66 1.45 1.28 1.13 1.01 0.90 0.80 0.72 0.65 0.59 0.54
0.88
SLU 4.15 3.78 3.46 3.17 2.93 2.71 2.51 2.34 2.18 2.04 1.91 1.79 1.69 1.59 1.50 1.42 1.35
L/200 4.15 3.78 3.46 3.17 2.93 2.71 2.51 2.34 2.18 2.02 1.80 1.60 1.44 1.29 1.17 1.06 0.96
L/250 4.15 3.78 3.46 3.17 2.93 2.71 2.37 2.08 1.83 1.62 1.44 1.28 1.15 1.04 0.94 0.85 0.77
L/300 4.15 3.78 3.46 3.07 2.63 2.27 1.98 1.73 1.52 1.35 1.20 1.07 0.96 0.86 0.78 0.71 0.64
1.00
SLU 4.99 4.53 4.14