Catalog Free

Solar power, wind power and power systems for alternative energy

Alternative Energy Equipment & Consultation for Residential, Commercial and Industrial Applications

SOLAR AND WIND POWER

6080 Knoll Dr. Middleville, Michigan 49333 Tel: (269)-795-5285 Fax: (269) 795-4365

Catalog Information

Our catalog reflects the most current information and equipment specifications, however minor changes can and do occur with manufacturers so the information is subject to change without notice. We will advise you of any changes prior to your order.

Prices shown are the MSRP for planning and budgetary purposes. Contact us for actual prices based on the particular item discount, quantity pricing or system package pricing.

Event Horizon

(269) 795-5285 © 2004 eventhorizons.net All rights reserved

Dedication. Professional Assistance. Excellent Prices.

.

http://www.solar4power.com/

http://www.poweriseverything.com/

Index Page 1 of 2 - Advanced Energy Group Products Catalog - Solar, wind and alternative power equipment.

ModulesSunWize SW seriesSunWize OEM seriesSunWize SW & OEM kits

Shell Solar SM seriesShell Solar SP & SQ seriesShell Solars ST seriesAstroPower AP & APxUniSolarUniSolar Roofing ProductsSanyoSharpGlobal Solar

.Module Interconnect/Output cables

MountsSunwize MountsPower-Fab MountsUniRac MountsZomeworks Mounts

ControllersSunWize-SW-IL6 Charge RegulatorSunWize-Steca Controller SunWize-Solsum ControllerMorningstar Prostar & SunSaver ControllersMorningstar SunGrd, SunLight, TriStar ControllersXantrex-CSeries ControllersSpecialtyConcepts ControllersRVPowerProducts ControllersOutback MX60 ControllerSunWize Lighting System Controller

Meters_Various

Wind TurbinesSouthwest Windpower Air-XSouthwest Windpower WhisperSunWize J-Box Assembly for Air-X

Water Pumps Aerovironment Solar Pump ControllerDankoff Solar Surface PumpsShurflo WaterpumpsGrundfos SQFlex, SA-1500 & Sizing ChartWaterpumping System Sizing Worksheet

RefrigeratorsSunDanzer RefrigeratorsSunDanzer Battery-Free RefrigeratorSunFrost Refrigerators

LightingSteca Lighting ProductsESL lampsLED fixtures and lampsFluorescent fixtures and lampsLPS fixtures and lampsSunWize PIR lights and systemsUni-Solar Lighting KitsOutdoor Solar Lantern

Electrical & SwitchgearConnect Energy PV Sys. Combiner BoxOutback PSPV and PSSB CombinerOutback Power System DCOutback Power System ACLightning ArrestorsAnalog MetersSafety SwitchesXantrex DC Disconnect & AccessoriesATO & 'SEA' Fuses, Fuse BlocksCircuit Breakers

Index Page 2 of 2 - Advanced Energy Group Products Catalog - Solar, wind and alternative power equipment.

BatteriesConcorde BatteriesMK BatteryIBE BatteriesRolls Battery EngineeringBattery Desulfators & Vent CapsSunWize Battery EnclosuresBattery CablesOutback Power Battery RacksSamlex SEC Battery ChargersXantrex Truecharge Battery Chargers Iota DLS Battery Chargers

InvertersOutback FX2000 Inverters Xantrex SunTieXR InvertersXantrex SW & SW+ InvertersXantrex DR InvertersXantrex UX, TS and Freedom 458 InvertersXantrex PROsine InvertersXantrex PROwatt InvertersSMA SunnyBoy InvertersExeltech XP InvertersGenius InvertersInvertek Inverters

Xantrex Power CentersSunWize Power CentersXantrex Accesories

FusesWire and CableFittingsTerminal BlocksWiring Reference Guide

Hardware

SunWize SystemsSW Solar Connect ProgramSW Residential Grid-Tie SystemsSW Battery ChargersSW Portable Energy SystemSW Portable Power GeneratorSW Solisto Solar Home SystemSW Power Ready SystemsSW Power StationSW Industrial DC Power SupplySW Backup Electric SystemsSW Designer Solar Lighting Systems

Shell Solar RV Power KitsShell Solar earthsafe Kits

.

MODULES

3/03

Solar Modules

SW Series Solar ModulesSunWize® Solar Modules deliver top-quality performance forall photovoltaic applications including rural electrification,water pumping, telemetry, communications, and generalbattery charging. SunWize modules can be used in single-module and multiple-module installations and are ideal forhigh voltage, grid-tied inverters. Each module consists of 36solar cells connected in series providing maximum chargingpower. UL listed, FM approved and ISPRA certified.

FEATURES:• The glass surface is impact resistant and allows maximum light transmission.

• Single crystalline solar cells are encapsulated and bonded to the glass in multiple layers of ethylene vinyl

acetate (EVA) and laminated with a white Tedlar™ backinginsuring long life in severe environmental conditions.

• A weather resistant junction box accommodates all wiring methods including moisture-tight strain relief connectors andelectrical conduit. Bypass diodes insure reliable operation.

• Anodized aluminum tubular frames add strength and durability to the modules. Pre-drilled mounting holes.

• SunWize modules are manufactured to comply with U.S. and international standards and are factory tested to verify superior performance.

• All SunWize modules carry a 20-year, 80% power output warranty.

SunWize®

Rated current and voltage at Maximum Power Point (MPP)

Model Rated Power Rated Voltage Rated Current Open Circuit Short Circuit Dimensions Unit Weight(Watts) (Vmp) (Imp) Voltage (Voc) Current (Isc) (inches) (lbs.) MSRP

SW85 85 17.4 4.88 21.4 5.70 56.89” x 22.83” 23 $542.00SW90 90 17.4 5.17 21.4 5.90 56.89” x 22.83” 23 $575.00SW100 100 16.7 6.00 21.0 6.70 56.93” x 25.43” 26 $645.00SW115 115 16.7 6.89 21.0 7.65 56.93” x 25.43” 26 $740.00SW120 120 16.7 7.18 21.0 8.00 56.93” x 25.43” 26 $772.00

SunWize SW85 & SW90

SunWize SW115 and SW120

SW 85 and SW 90 Module Dimensions

SW Series Module Junction Box

A d v a n c e d E n e r g y G r o u p

Solar Modules

MOD

ULES

3/03

OEM Series Solar ModulesSunWize® OEM modules deliver top-quality performance for all photovoltaic applicationsincluding rural electrification, water pumping, telemetry, communications, and general batterycharging. Ideal for AC and DC installations, SunWize OEM modules can be used in single-module and multiple-module systems. Each module consists of 36 solar cells connected inseries providing maximum charging power. The glass surface is impact resistant and allowsmaximum light transmission. Single crystalline solar cells are encapsulated and bonded to theglass in multiple layers of ethylene vinyl acetate (EVA) and laminated with a white Tedlar™backing insuring long life in severe environmental conditions. Bypass diodes contained within thejunction box insure reliable operation. Anodized aluminum tubular frames add strength anddurability to the modules. Includes pre-drilled mounting holes. The weather resistant junction boxaccommodates all wiring methods including moisture-tight strain relief connectors and electricalconduit. SunWize modules carry a 20-year, 80% power output warranty. FM approved.

SunWize®


Model Rated Power Rated Voltage Rated Current Open Circuit Short Circuit Dimensions Unit Weight(Watts) (Vmp) (Imp) Voltage (Voc) Current (Isc) (inches) (lbs.) MSRP

OEM5 5 16.4 0.31 20.5 0.38 11.82” x 9.84” 3 $81.00

OEM10 10 16.4 0.61 21.0 0.70 15.15” x 14.76” 4.5 $111.00

OEM20 20 16.5 1.22 21.0 1.38 20.86” x 16.93” 6.5 $171.00

OEM40 40 16.7 2.40 21.0 2.68 38.38” x 17.13” 12.5 $271.00

MODULE DIMENSIONS

A

BE

C

D

Ø.275

OEM A B C D E5 9.84 11.82 8.66 7.87 –

10 14.76 15.15 13.58 9.84 –20 16.93 20.86 15.75 9.84 –40 17.13 38.38 15.90 9.84 23.64

SunWize OEM5

SunWize OEM20

SunWize OEM10

SunWize OEM40


MODULES

3/03 5

Solar Modules

SunWize OEM and SW Solar Module kits include a solar module and the SunWize SWIL6 prewiredvoltage regulator with output cable. The OEM kits are also offered with a fixed tilt, 45˚ side-of-polemount. Each kit is also available without the mount. The SWIL6 is mounted in the module junctionbox. The waterproof controller features a multi-function LED indicator and fuse protection.SunWize single crystalline, high-efficiency solar modules are manufactured to exceed industrystandards providing exceptional reliability and maximum power output. A twenty-year warrantyreflects the superior quality and assures long product life. The aluminum side-of-pole mountsinclude two clamps for nominal 2.5” through 4” poles (OD 2.875” through 4.5”). OEM 5 & 10 kitsinclude a 5 ft.cable, the OEM 20 & 40 and the SW85 & 90 kits include a 10 ft. cable (#12 AWG).

SunWize® OEM and SW Solar Module Kits

SunWize OEM 10 Kit


Model Rated Power Rated Voltage Rated Current Open Circuit Short Circuit Dimensions Kit Weight(Watts) (Vmp) (Imp) Voltage (Voc) Current (Isc) (inches) (lbs) MSRP

OEM5 kit 5 16.4 0.31 20.5 0.38 11.82” x 9.84” 7.0 $179.00OEM5 kit without mount 5.75 $159.00




SW85 kitwithout mount 85 17.4 4.88 21,4 5.70 56.89” x 22.83” 23.0 $696.00

SW90 kitwithout mount 90 17.4 5.17 21.4 5.90 56.89” x 22.83” 23.0 $729.00

Note: modules, charge controllers and mounts can be purchased separately.

SunWize Spotlight

LOCATION:Dry Tortugas National Park, Florida

APPLICATION:Facility power system

SYSTEM:SunWize 14.4 kW PV Hybrid System


Solar Modules

MOD

ULES

3/03

SM Series Solar Module Features• The SM Series has a square-shaped solar cell providing the highest

power density of all Shell Solar modules• The SM Series is Shell Solar’s premium modules with the longest

service record having been deployed in the field for over 25 years• Mono-crystalline Power Max® solar cells, are textured and

anti-reflection coated for maximum output ratios• Highly transparent tempered glass delivers more power and

ensures high impact resistance and protection against hail, snow, ice and storms

Shell Solar

Shell SM110-24P

110

35.0

3.15

43.5

3.45

600

24

51.8 (1316)

26 (660)

2.2 (56)

1.6 (40)

25.1 (11.5)

ProCharger TM - CR

screws

mounting holes

no

IEC61215

UL-Listing 1703

TÜVIsolationClassII

25

715.00

Shell SM55

55

17.4

3.15

21.7

3.40

600

12

50.9 (1293)

13 (329)

1.3 (35)

1.3 (35)

12 (5.5)

ProCharger TM - S

screws

mounting holes

no

IEC61215

UL-Listing 1703


25

$390.00

MODULE TYPE

Electrical Characteristics

Peak power (Pmpp)

Peak power voltage (Vmpp)

Peak power current (Impp)

Open circuit voltage (Voc)

Short circuit current (Isc)

Maximum system voltage (Vsyst. max)

Nominal voltage

Physical Characteristics

Length

Width

Depth including junction box

Depth excluding junction box

Weight

Junction box

Connection type

Mechanical mount

Mounting bolts included

Certificates

Limited Peak Power Warranty

MSRP

Power specifications are at Standard Test Conditions (STC): irradiance level 1000W/m2, spectrum AM 1.5 and cell temperature 25ºC.

(W)

(V)

(A)

(V)

(A)

(V)

(V)

(mm)

(mm)

(mm)

(mm)

(kg)

(years)

in.

in.

in.

in.

lbs.

Shell SM50-H

50

15.9

3.15

19.8

3.40

600

12

48 (1220)

13 (329)

1.3 (35)

1.3 (35)

11.5 (5.2)

ProCharger TM - S

screws

mounting holes

no

IEC61215

UL-Listing 1703


25

$370.00

Shell SM110-12P

110

17.5

6.3

21.7

6.9

600

12

51.8 (1316)

26 (660)

2.2 (56)

1.6 (40)

25.1 (11.5)

ProCharger TM - CR

screws

mounting holes

no

IEC61215

UL-Listing 1703


25

$715.00

Shell SM110-12P, Shell SM110-24-PShell SM55


MODULES

3/03

Solar Modules

SP Series Solar Modules - see important information below.• The SP Series was Shell Solar’s most popular and best selling module,however, it has been improved - see Shell SQ Modules. The SP Series is available only until current inventory is gone.

Check for availability or use the newest SQ Series modules.• The SP modules are high quality, single crystalline PowerMax®

technology used in other Shell Solar modules. They are laminated to tempered glass and include anodized aluminum frames.

• Modules can be wired in series or parallel to attain required power levels.

• The universal conduit-ready junction box design allows for easy field replacement of diodes. In addition, cable assemblies are field replaceable for the Shell SP140-PC and the SP150-PC.

• Built-in bypass diodes ensure peak system performance.

Shell Solar

Shell SP140-PC and Shell SP150-PC

Shell SP75

75

8.50*/17.0

8.8*/4.4

10.85*/21.7

9.6*/4.8

600

6*/12

47.2 (1200)

20.8 (527)

2.2 (56)

1.3 (34)

16.7 (7.6)

ProCharger TM - CR

screws

mounting holes

no

IEC61215

UL-Listing 1703


FM

25

$489.00

Shell SP150-PC

150

34.0

4.4

43.4

4.8

600

24

63.9 (1622)

32.1 (814)

2.2 (56)

1.6 (40)

38 (17.2)

ProCharger TM - CR

cable

mounting holes

no

IEC61215

UL-Listing 1703


25

$975.00

MODULE TYPE


Peak power (Pmpp)






Nominal voltage


Length

Width



Weight

Junction box

Connection type

Mechanical mount


Certificates


MSRP

*The Shell SP75 and Shell SP70 may be reconfigured in the field for 6V operation.Power specifications are at Standard Test Conditions (STC): irradiance level 1000W/m2, spectrum AM 1.5 and cell temperature 25ºC.

(W)

(V)

(A)

(V)

(A)

(V)

(V)

(mm)

(mm)

(mm)

(mm)

(kg)

(years)

in.

in.

in.

in.

lbs.

Shell SP70

70

8.25*/16.5

8.50*/4.25

10.7*/21.4

9.4*/4.7

600

6*/12

47.2 (1200)

20.8 (527)

2.2 (56)

1.3 (34)

16.7 (7.6)

ProCharger TM - CR

screws

mounting holes

no

IEC61215

UL-Listing 1703


FM

25

$455.00

Shell SP140-PC

140

33.0

4.25

42.8

4.7

600

24

63.9 (1622)

32.1 (814)

2.2 (56)

1.6 (40)

38 (17.2)

ProCharger TM - CR

cable

mounting holes

no

IEC61215

UL-Listing 1703


25

$910.00

UPDATE: Shell SP70 and Shell SP75 are no longer available.


go

UPDATE:

go

The

go

SP

go

Series

go

is

go

available

go

only

go

until

go

current

go

inventory

go

is

go

gone.

go

Check

go

for

go

availability

go

or

go

use

go

the

go

newest

go

SQ

go

Series

go

modules.

Shell SolarProduct Information Sheet

Shell SQ75 Photovoltaic Solar Module

GeneralThe Shell SQ75 module contains 36 seriesconnected 125 x 125 mm PowerMax® mono-crystalline silicon solar cells.

The Shell SQ75 can generate a peak power of 75 watts at 17 volts.

The Shell SQ75 solar module has beendesigned for grid connected and industrialapplications.

Qualificationsand CertificatesThe Shell SQ75 solar module meets thefollowing requirements:

• IEC 61215 (Pending)

• UL - Listing 1703

• FM approved

• TÜV Safety Class II (Pending)

All Shell Solar modules are produced in EN-ISO 9001certified factories.

Limited Warranties• Peak Power for 25 years*

*See Shell Solar Limited Warranty for PV-Modules

Shell SQ75 Module

Junction BoxThe junction box provides a high quality, dustprotected and splash proof IP54-rated housing.The housing contains a rigid connection blockwith screw terminals and by-pass diodesproviding "hot spot" protection for the solar cells.

Benefits• PowerMax® mono-crystalline solar cells

deliver maximum power output even underreduced light conditions.

• Dense packing of cells provides more powerwhere space is a limitation and creates auniform aesthetic.

• Ideal for large grid connected systems wherehigh power density minimizes system costs.

• Tight electrical specifications guaranteeindustry leading energy yield performance.

• Highly transparent tempered glass deliversmore power and ensures high impactresistance and protection against hail, snow,ice, and storms.

• Over 300MW of cumulative installedexperience has been applied to the evolutionof our mono-crystalline range to ensure thatour products have a long and reliable servicelife backed by a 25 year warranty.

ProCharger™–CR Junction Box

Maximum conductor cross-section: 4 mm2

Type of protection: IP54

Number of by-pass diodes: 2

ELECTRICAL EQUIPMENT, CHECK WITH YOUR INSTALLER

Due to continuous research and product improvement the specifications in this Product Information Sheet aresubject to change without notice. Specifications can varyslightly. For installation and operation instructions, seethe applicable manuals. No rights can be derived fromthis Product Information Sheet and Shell Solar assumesno liability whatsoever connected to or resulting from the use of any information contained herein.

MechanicalSpecifications Module A torsion and corrosion-resistant anodizedaluminium frame ensures dependableperformance, even under harsh weatherconditions. Pre-drilled mounting holes areprovided for ease of installation.

Outside dimensions (in) 47.2 x 20.8

Thickness (inc. junction box) (in) 2.2

Thickness (exc. junction box) (in) 1.3

Weight (lbs) 16.7

For installation instructions, please refer to the Installation Manual which is availablefrom Shell Solar.

Electrical CharacteristicsData at Standard Test Conditions (STC)

STC: irradiance level 1000W/m2, spectrum AM 1.5 and cell temperature 25°C

Rated power Pr 75W

Peak power Pmpp 75W

Peak power voltage Vmpp 8.5*/17V

Peak power current Impp 8.8*/4.4A

Open circuit voltage Voc 10.85*/21.7V

Short circuit current Isc 9.6*/4.8A

Series fuse rating 15A

Minimum peak power Pmpp min 70W

The abbreviation ‘mpp’ stands for MaximumPower Point.

Typical data at Nominal Operating CellTemperature (NOCT) conditions

NOCT: 800W/m2 irradiance level, AM 1.5spectrum, wind velocity 1m/s, Tamb 20°C

Temperature TNOCT 46°C

Mpp power Pmpp 54W

Mpp voltage Vmpp 15.4V

Open circuit voltage Voc 19.9V

Short circuit current Isc 3.9A

* The Shell SQ75 may be reconfigured in thefield for 6V operation

Typical data at low irradiance

The relative reduction of module efficiency at an irradiance of 200W/m2 in relation to1000W/m2 both at 25°C cell temperature and AM 1.5 spectrum is 8%.

Temperature coefficients

α Pmpp -0.52%/°C

α Vmpp -84mV/°C

α Isc 1.4mA/°C

α Voc -81mV/°C

Typical I/V CharacteristicsThe I/V graph below shows the typicalperformance of the solar module at variouslevels of irradiance.

The I/V graph below shows the typicalperformance of the solar module at various celltemperatures.

0

1

2

3

4

5

0 5 10 15 20 25

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

1000W/m²

800W/m²

600W/m²

400W/m²

Cell temperature 25°C

200W/m²

0

1

2

3

4

5

0 5 10 15 20 25

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

40°C

20°C

50°C

30°C

60°C

Irradiance : 1000 W/m²

47.2

(120

0)

25.3

(643

)

46.1

(117

2)

20.8 (527)

1.3 (34)

2.2 (56)

19 (483)

Shell SQ75Photovoltaic Solar Module

V4/SQ75/08/03/US

*inches (mm)

Maximum system voltage: 600 Vdc (UL)and 715 Vdc (TÜV Safety Class II)


Shell SQ80 Photovoltaic Solar Module

GeneralThe Shell SQ80 module contains 36 seriesconnected 125 x 125 mm PowerMax® mono-crystalline silicon solar cells.

The Shell SQ80 can generate a peak power of 80 watts at 17.5 volts.

The Shell SQ80 solar module has beendesigned for grid connected and industrialapplications.

Qualificationsand CertificatesThe Shell SQ80 solar module meets thefollowing requirements:


• UL - Listing 1703

• FM approved





Shell SQ80 Module

Junction BoxThe junction box provides a high quality, dustprotected and splash proof IP54-rated housing.The housing contains a rigid connection blockwith screw terminals and by-pass diodesproviding "hot spot" protection for the solar cells.








ProCharger™–CR Junction Box










Weight (lbs) 16.7




Rated power Pr 80W

Peak power Pmpp 80W

Peak power voltage Vmpp 8.75*/17.5V

Peak power current Impp 9.17*/4.58A

Open circuit voltage Voc 10.9*/21.8V

Short circuit current Isc 9.7*/4.85A







Mpp power Pmpp 58W

Mpp voltage Vmpp 16V

Open circuit voltage Voc 20V


* The Shell SQ80 may be reconfigured in the field for 6V operation




α Pmpp -0.52%/°C

α Vmpp -84mV/°C

α Isc 1.4mA/°C

α Voc -81mV/°C



0

1

2

3

4

5

0 5 10 15 20 25

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

1000W/m²

800W/m²

600W/m²

400W/m²


200W/m²

0

1

2

3

4

5

0 5 10 15 20 25

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

40°C

20°C

50°C

30°C

60°C


47.2

(120

0)

25.3

(643

)

46.1

(117

2)

20.8 (527)

1.3 (34)

2.2 (56)

19 (483)

Shell SQ80Photovoltaic Solar Module

V4/SQ80/08/03/US

*inches (mm)



Shell SQ150-PC Photovoltaic Solar Module

GeneralThe Shell SQ150-PC module contains 72 seriesconnected 125 x 125 mm PowerMax® mono-crystalline silicon solar cells.

The Shell SQ150-PC can generate a peakpower of 150 watts at 34.0 volts.

The Shell SQ150-PC solar module has beendesigned for grid connected and industrialapplications.

The Shell SQ150-P is the non-cable version ofthe Shell SQ150-PC and is available uponspecial order. The Shell SQ150-P does notinclude the cable and fitting asssembly.

Qualificationsand CertificatesThe Shell SQ150-PC solar module meets thefollowing requirements:


• UL – Listing 1703

• FM approved (Shell SQ150-P only)





Shell SQ150-PC Module

Junction BoxThe junction box provides a high quality, dustprotected and splash proof IP54-rated housing.The housing contains a rigid connection block with screw terminals and by-pass diodes providing"hot spot" protection for the solar cells.

For ease of installation, the junction box includesmale and female MultiContact® flying cables.

The universal junction box design allows for easy,field replacement of diode or cable assemblies.








• Cables and MultiContact® plugs pre-assembled to reduce installation time ingrid connected applications

ProCharger™–CR Cable Junction Box










Weight (lbs) 38

Cable length - male (in) 51

Cable length + female (in) 39




Rated power Pr 150W

Peak power* Pmpp* 150W

Peak power voltage Vmpp 34V

Peak power current Impp 4.4A




Minimum peak power Pmpp min 142.5W

*Tolerance on Peak Power ±5%





Mpp power Pmpp 108W







α Pmpp -0.52%/°C

α Vmpp -167mV/°C

α Isc 1.4mA/°C

α Voc -161mV/°C



Shell SQ150-PCPhotovoltaic Solar Module

0

1

2

3

4

5

0 5 10 15 20 25 30 35 40 45

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

1000W/m²

800W/m²

600W/m²

400W/m²


200W/m²

0

1

2

3

4

5

0 5 10 15 20 25 30 35 40 45

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

40°C

20°C

50°C

30°C

60°C


Do Not Use As Grip

63.9

(162

2)62

.5 (1

589)

25.3

(643

)

32.1 (814)

1.6 (40)

2.2 (56)

30.3 (769)

V4/SQ150--PC/08/03/US

*inches (mm)



Shell SQ160-PC Photovoltaic Solar Module

GeneralThe Shell SQ160-PC module contains 72 seriesconnected 125 x 125 mm PowerMax® mono-crystalline silicon solar cells.

The Shell SQ160-PC can generate a peakpower of 160 watts at 35.0 volts.

The Shell SQ160-PC solar module has beendesigned for grid connected and industrialapplications.

The Shell SQ160-P is the non-cable version ofthe Shell SQ160-PC and is available uponspecial order. The Shell SQ160-P does notinclude the cable and fitting asssembly.

Qualificationsand CertificatesThe Shell SQ160-PC solar module meets thefollowing requirements:


• UL – Listing 1703

• FM approved (Shell SQ160-P only)





Shell SQ160-PC Module

Junction BoxThe junction box provides a high quality, dustprotected and splash proof IP54-rated housing.The housing contains a rigid connection block with screw terminals and by-pass diodes providing"hot spot" protection for the solar cells.

For ease of installation, the junction box includesmale and female MultiContact® flying cables.

The universal junction box design allows for easy,field replacement of diode or cable assemblies.








• Cables and MultiContact® plugs pre-assembled to reduce installation time ingrid connected applications

ProCharger™–CR Cable Junction Box










Weight (lbs) 38

Cable length - male (in) 51

Cable length + female (in) 39




Rated power Pr 160W

Peak power* Pmpp* 160W

Peak power voltage Vmpp 35V

Peak power current Impp 4.58A





*Tolerance on Peak Power ±5%





Mpp power Pmpp 115W


Open circuit voltage Voc 40V





α Pmpp -0.52%/°C

α Vmpp -167mV/°C

α Isc 1.4mA/°C

α Voc -161mV/°C



0

1

2

3

4

5

0 5 10 15 20 25 30 35 40 45

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

1000W/m²

800W/m²

600W/m²

400W/m²


200W/m²

0

1

2

3

4

5

0 5 10 15 20 25 30 35 40 45

Module Voltage (V)

Mo

du

le C

urr

en

t (A

)

40°C

20°C

50°C

30°C

60°C


Do Not Use As Grip

63.9

(162

2)62

.5 (1

589)

25.3

(643

)

32.1 (814)

1.6 (40)

2.2 (56)

30.3 (769)

Shell SQ160-PCPhotovoltaic Solar Module

V4/SQ160--PC/08/03/US

*inches (mm)


Solar Modules

MOD

ULES

3/03

ST Series Solar Module Features• Multiple layer CIS solar cells capture a broad spectrum of light to

deliver excellent power performance even in reduced light conditions

• Conductive front layer of zinc oxide provides superior light transmission to enhance output

• Black anodized aluminum frame secures the glass front laminate for durability

• Uniform flat-black appearance is visually compatible with a varietyof installation requirements

• 10 year limited warranty on power output

Shell Solar

Shell ST40(not shown to scale)

MODULE TYPE


Peak power (Pmpp)






Nominal voltage


Length

Width



Weight

Junction box

Connection type

Mechanical mount


Certificates


MSRP

Power specifications are at Standard Test Conditions (STC): irradiance level 1000W/m2, spectrum AM 1.5 and cell temperature 25ºC.

(W)

(V)

(A)

(V)

(A)

(V)

(V)

(mm)

(mm)

(mm)

(mm)

(kg)

(years)

in.

in.

in.

in.

lbs.

Shell ST5

5

15.6

0.32

22.9

0.39

25

12

12.9 (328)

8.1 (206)

1.3 (35)

1.3 (35)

3.1 (1.4)

n/a

cable

mounting holes

no

UL-Listing 1703

FM

10

$75.00

Shell ST10

10

15.6

0.64

22.9

0.77

25

12

15.3 (387)

12.9 (328)

1.3 (35)

1.3 (35)

5.2 (2.4)

n/a

cable

mounting holes

no

UL-Listing 1703

FM

10

$132.00

Shell ST40

40

16.6

2.41

23.3

2.68

600

12

50.9 (1293)

12.9 (328)

1.3 (35)

1.3 (35)

15.4 (7)

ProCharger TM - S

screws

mounting holes

no

UL-Listing 1703

10

$300.00

Shell ST20

20

15.6

1.29

22.9

1.54

25

12

29.5 (748)

12.9 (328)

1.3 (35)

1.3 (35)

9 (4.1)

n/a

cable

mounting holes

no

UL-Listing 1703

10

$226.00

Shell ST5 Shell ST10 Shell ST20


MODULES

3/03

Solar Modules

AP Module Features All AstroPower modules are manufactured to withstand the harshest climate extremes. Weatherresistant junction boxes, including protective bypass diodes, allow easy and safe field inter-connection. Heavy-duty anodized aluminum frames provide strength and convenient mountingaccess. All AstroPower modules are UL listed and carry a 20-year warranty. Also available inblack frame – special order.

APx Module FeaturesThe APx-130 and 140 apply AstroPower's APex™ polycrystallinesilicon technology in a ultra-large module format. The bluebacksheet and black frame provide a uniform visual appearancethat make this product ideal for large-scale commercial orindustrial installations. UL listed, 20-year warranty.

AstroPower


Model Rated Power Rated Voltage Rated Current Open Circuit Short Circuit Dimensions Unit Weight(Watts) (Vmp) (Imp) Voltage (Voc) Current (Isc) (inches) (lbs) MSRP

AP-50 50 16.7 3.0 21.5 3.3 33.8” x 26” 16.6 $335.00

AP-110 110 16.7 6.6 20.7 7.5 58.1” x 26” 26.1 $725.00

AP-120 120 16.9 7.1 21.0 7.7 58.1” x 26” 26.1 $785.00

APx-130 130 15.3 8.5 19.1 9.9 34.5” x 77.2” 46.0 $785.00

APx-140 140 15.7 8.9 19.4 10.1 34.5” x 77.2” 46.0 $845.00

APx-130/140

AP-110/120

AP-50

Specifications/Physical CharacteristicsModel Name AP-50 AP-110 APx-130

AP-120 APx-140

Length, inches [mm] 33.8 [859] 58.1 [1477] 77.2 [1961Width, inches [mm] 26.0 [661] 26.0 [661] 34.5 [875]Depth (frame), inches [mm] 1.4 [35] 1.4 [35] 1.4 [35]Depth (including j-box), inches [mm] 2.1 [54] 2.1 [54] 2.1 [54]Weight, pounds [kg] 10.0 [4.5] 26.1 [11.9] 46.0 [20.9]

Mounting Holes:“A” - Center Spacing, inches [mm] 18.9 [481] 25.3 [643] 46.7 [1186]“B” - Edge Distance, inches [mm] 7.4 [189] 16.4 [417] 15.3 [388]“C” - Width Spacing, inches [mm] 24.3 [616] 24.3 [616] 32.8 [832]“D” - Outer Spacing, inches [mm] n/a n/a n/a“E” - Outer Edge Spacing, inches, [mm] n/a n/a n/aDiameter mounting holes, inches [mm] .26 [6.7] .26 [6.7] .26 [6.7]

A

C

B

D

E


Solar Modules

MOD

ULES

3/03



US-3 2.68 8.10 0.33 12.0 0.40 11.26” x 8.07” 1.7 $53.00

US-5 5 16.5 0.30 23.8 0.37 19.33” x 8.07” 2.5 $66.00

US-11 10.3 16.5 0.62 23.8 0.78 19.33” x 15.08” 3.6 $128.00

US-21 21 16.5 1.27 23.8 1.59 36.54” x 15.07” 6.6 $177.00

US-32 32 16.5 1.94 23.8 2.40 53.78” x 15.07” 10.0 $226.00

US-42 42 16.5 2.54 23.8 3.17 36.55” x 29.18” 13.8 $277.00

US-64 64 16.5 3.88 23.8 4.80 53.78” x 29.18” 20.2 $405.00

US-116 116 30.0 3.88 43.2 4.80 97.00” x 30.20” 44 $721.00

UNI-POWER™ Module Features UNI-POWER modules are exceptional in performance and durability. The heart of theUNI-POWER module is the Triple Junction silicon solar cell unique to Uni-Solar. Each cellis composed of three semiconductor junctions stacked on top of each other for diverselight level absorption. This spectrum splitting capability is the key to higher efficiencyand superior operation in low lightlevels. The cell junctions aredeposited onto a stainless steel filmencapsulated in UV stabilized EVA

polymers and laminated to a Galvalume™ coated, steel backing plate.The modules feature a clear Tefzel® front covering. The unbreakable,non-glass module is bonded to an anodized aluminum frame forstrength. Frame includes mounting holes. The US-116, US-64, US-42and US-32 feature bypass diodes, weather resistant junction boxeswith 1/2 NPT knock outs and carry a twenty-year limited warranty.The US-21, US-11 and US-5 carry a ten-year limited warranty andinclude an 8’ cable. The US-3 features a built-in blocking diode andcarries a three-year limited warranty. US-116 is configured for 24 voltoperation, all others 12 volt operation. All are UL listed.

UNI-SOLAR®

Flexible Solar Battery ChargersEach UNI-SOLAR battery charger incorporates the same Triple Junction solarcell technology as the Uni-Power module. The flexible modules areexceptionally durable and are encapsulated in EVA and bonded and stitchedto a cushioned, vinyl and foam backing material. The modules feature a clearTefzel® front covering. Bypass diodes are connected across each cell,allowing the modules (excluding FLX-5) to produce power even whenpartially shaded. Blocking diodes are included in a small sealed junction boxlocated at the top of the module. Each panel has 8 feet of cable with 2-pinSAE connector, and is packaged with a 2-foot fused battery cable. Thesemodules carry a three-year limited warranty and are UL listed.

UNI-SOLAR®


FLX-5 5 16.5 0.30 23.8 0.37 21.80” x 9.71” 1.18 $95.00

FLX-11 10.3 16.5 0.62 23.8 0.78 21.80” x 16.70” 2.00 $159.00

FLX-32 32 16.5 1.94 23.8 2.40 56.27” x16.70” 4.70 $325.00


UniSolar US-3

From top: US-64, US-42, US-32From top: US-21, US-11, US-5


Model Rated Power Rated Voltage Rate Current Open Circuit Short Circuit Dimensions Unit Weight(Watts) (Vmp) (Imp) Voltage (Voc) Current (Isc) (feet) (lbs) MSRP

SHR-17 17 9 1.9 13 2.35 7.2’ x 1’ 1.4 $142.00

MODULES

3/03

Solar Modules

PV ShinglesThe flexible thin-film solar cell shingles can be installed in new construction nailed in place usingcommon roofing nails on conventional roof decking over 30-lb felt underlayment. They can also beplaced over existing roofing. The surface is textured to blend and complement the granularsurface of the surrounding conventional shingles. Two, 12” long, 18-gauge lead wires exit from theunderside of each shingle. Lead wires on the backside of the head-lap pass through the roof deckto allow wiring connections to be made in the roof space. The sun warms the solar electric shingleproviding a bond that forms a weather-resistant covering. UL listed.

Field Applied PV Roofing LaminateField applied thin-film solar laminates can be applied to standing seam metal roofing materials inthe field for a total custom look. You don’t have to compromise the aesthetics of your home to getthe energy independence you want. The PVL Roofing Laminates are made exceptionally durableby encapsulation in UV stabilized polymers. Bypass diodes are connected across each cell,allowing the modules to produce power even when partially shaded. They come with the bondingadhesive factory applied on the back of the laminate. Rugged, weatherproof junction box.

• Lightweight, flexible product construction • Easy peel and stick installation • Roll shippable• UL listed, 20-year warranty (only on products installed by a UniSolar certified installer).

Uni-Solar PV Shingles

UNI-SOLAR® Roofing Products

Uni-Solar Field Applied PV Roofing Laminate

Model Rated Rated Rated Open Short Dimensions WeightPower Voltage Current Circuit Circuit (lbs.) MSRP

PVL-29T 29 7.5 3.88 10.8 4.8 55.5” x 15.5” 4.1 $229.00PVL-58T 58 15.0 3.88 21.6 4.8 102.75” x 15.5” 8.2 $415.00PVL-64T 64 16.5 3.88 23.8 4.8 112.15” x 15.5” 9.0 $449.00PVL-128T 128 33.0 3.88 47.6 4.8 216” x 15.5” 17.0 $849.00

Removing the backing and unrolling Uni-Solar PVL solar panels Locating and installing the PVL junction box


Sanyo HIT Solar ModulesSanyo’s HIT modules use a blend of amorphous and crystalline silicon to deliver a high cellconversion efficiency. All Sanyo modules feature MC connectors/cables pre-wired into a conduit-ready junction box and are equipped with factory installed bypass diodes to provide circuitprotection. The anodized aluminum tubular frames are designed for top down mounting clips.

Sanyo solar modules are ideal for grid-tie applications. Unlike other modules that include aguarantee of plus or minus 10% of their rated output, Sanyo offers a unique guarantee that theirmodules never produce less than the rated power output. Sanyo modules also outperform allother modules due to the fact that they maintain higher voltages at higher temperatures - whichmeans more power and better performance. The result is one of the highest Performance TestCondition ratings per watt (W ptc) for higher rebates in California. Performance Test Conditiontesting simulates the real world, high cell temperature modules are subjected to in the field.Check the SunWize System section for complete SunWize residential kits that include the Sanyomodules. UL Listed. 20 year limited warranty.

Model Watts Vmp Imp Voc Isc Dimensions Weight MSRP

HIP-G751BA2 167 51.4 3.23 64.9 3.63 52.0” x 35.24” 33 $1,136.00HIP-J54BA2 180 54.0 3.33 66.4 3.65 52.0” x 35.24” 33 $1,225.00

Solar Modules

MOD

ULES

12 3/03

Model Rated Power Rated Voltage Rated Current Deployed Stowed Unit Weight(Watts) (Vmp) (Imp) Dimensions Dimensions (lbs.) MSRP

P3A-12-66 12 19.6 0.60 10.5” x 46” x .06” 10.5” x 4.2” x 0.8” 0.99 $749.00P3-17-60 17 18.8 0.90 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $579.00 P3-17-72h 17 19.6 0.85 21.0” x 28” x 0.1” 10.5” x 8.5” x 1.2” 2.0 $579.00P3-25-60 25 18.8 1.30 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $775.00P3-25-72 25 19.6 1.30 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $775.00P3-30-60 30 18.8 1.50 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $839.00P3-30-72 30 19.6 1.50 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $839.00P3-36-72 36 19.6 1.80 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $999.00P3-42-108 42 18.8/37.6 2.2/1.1 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,199.00P3-48-108 48 18.8/37.6 2.5/1.3 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,349.00P3-56-108 56 18.8/37.6 3.0/1.5 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,549.00

Portable Power PacksPortable Power Packs are lightweight, foldable power sources for rugged, self-sustaining power. • Suitable for any portable 12V load or 24V above 40 watts • Blocking diodes • Standard 2 prong trailer plug provided • Fold into compact size for easy transport and deployment• Rip stop nylon backing available in Forest or Desert Camo or Forest Green.

Global Solar

P3-108 Portable Power Pack, shown deployed and stowed

Sanyo

Sanyo 167 watt HIT module

895 (35.24)

35 (35.26)

16 (0.63)

107 (0.63)

455 (17.93)

155

(6.1

1)

1320

(52.

0)

212.

5 (8

.37)

330

(13.

0)

212.

5 (8

.37)

330

(13.

0)

Junction Box with wiring (right);Cell structure of HIT solar cell (below)

Negative Positive

Top electrode Amorphous silicon

Single crystallinesiliconAmorphous siliconBottom electrode

Negative Positive


Module Output CablesModule Output Cables are used for connection from the solar array to the controller or PV combiner assemblies. Cables aresunlight-resistant, PVC tray cable and direct burial with red/black THHN conductors (rated 90˚ C, 600 volt). All are cut to lengthand outfitted with two strain-relief cord connectors for 1/2” NPT, one end terminated for connection into PV junction box, #10AWG with fork terminals, #8-6AWG with copper lugs.

MSRP MSRP MSRP MSRP

AWG-Conductors 10FT 20FT 30FT 50 FT

#10-2 $22.50 $33.25 $41.75 —————-#8-2 $41.50 $58.75 $77.25 $108.00#6-2 $47.50 $63.75 $83.00 $117.00

MODULES

3/03

Solar Modules

Module Output Cables

SunWize

Solar Module FeaturesSharp’s modules are designed for a variety of electrical power requirements. Based on crystalsilicon solar technology, the modules have superb durability to withstand rigorous operatingconditions. The 123 and 165 watt modules use multi-crystal silicon solar cells and the 175 and185 watt modules use single crystal silicon solar cells. The modules feature bypass diodes tominimize power drop caused by shade and BSF (Black Surface Field) structure to improve cellconversion efficiency. Aluminum frames. All modules are UL listed, include a 51” lead wire with MCconnectors and carry a 25-year warranty.

Sharp

Sharp ND-L3E1U 123W module

Sharp NT-S5E1U 185W module


ND-L3E1U 123 17.2 7.16 21.3 8.12 59.02” x 26.06” 30.87 $799.00NE-Q5E2U 165 34.6 4.77 43.1 5.46 62.00” x 32.52” 37.49 $1079.00NT-R5E1U 175 35.4 4.95 44.4 5.55 62.00” x 32.52” 37.49 $1159.00NT-S5E1U 185 36.2 5.11 44.9 5.75 62.00” x 32.52” 37.49 $1225.00

NE-Q5E2U 165W module

Physical Dimensions in inches

MODEL A B C D E F G H

175/185 62.0 32.5 1.8 30.9 19.1 7.3 30.5 51.1

165 62.0 32.5 1.8 30.9 19.1 7.3 30.5 51.1

123 59.0 26.0 1.8 29.5 n/a 9.8 24.4 51.1


T E C H N O L O G I E SSunWize ®

Sanyo HIT Solar ModulesSanyo’s HIT modules use a blend of amorphous and crystalline silicon to deliver a high cellconversion efficiency. All Sanyo modules feature MC connectors/cables pre-wired into a conduit-ready junction box and are equipped with factory installed bypass diodes to provide circuitprotection. The anodized aluminum tubular frames are designed for top down mounting clips.

Sanyo solar modules are ideal for grid-tie applications. Unlike other modules that include aguarantee of plus or minus 10% of their rated output, Sanyo offers a unique guarantee that theirmodules never produce less than the rated power output. Sanyo modules also outperform allother modules due to the fact that they maintain higher voltages at higher temperatures - whichmeans more power and better performance. The result is one of the highest Performance TestCondition ratings per watt (W ptc) for higher rebates in California. Performance Test Conditiontesting simulates the real world, high cell temperature modules are subjected to in the field.Check the SunWize System section for complete SunWize residential kits that include the Sanyomodules. UL Listed. 20 year limited warranty.


HIP-G751BA2 167 51.4 3.23 64.9 3.63 52.0” x 35.24” 33 $1,136.00HIP-J54BA2 180 54.0 3.33 66.4 3.65 52.0” x 35.24” 33 $1,225.00

Solar Modules

MOD

ULES

3/03

Model Rated Power Rated Voltage Rated Current Deployed Stowed Unit Weight(Watts) (Vmp) (Imp) Dimensions Dimensions (lbs.) MSRP

P3A-12-66 12 19.6 0.60 10.5” x 46” x .06” 10.5” x 4.2” x 0.8” 0.99 $749.00P3-17-60 17 18.8 0.90 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $579.00 P3-17-72h 17 19.6 0.85 21.0” x 28” x 0.1” 10.5” x 8.5” x 1.2” 2.0 $579.00P3-25-60 25 18.8 1.30 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $775.00P3-25-72 25 19.6 1.30 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $775.00P3-30-60 30 18.8 1.50 21.0” x 44” x 0.1” 10.5” x 8.5” x 1.2” 3.1 $839.00P3-30-72 30 19.6 1.50 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $839.00P3-36-72 36 19.6 1.80 21.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 3.7 $999.00P3-42-108 42 18.8/37.6 2.2/1.1 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,199.00P3-48-108 48 18.8/37.6 2.5/1.3 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,349.00P3-56-108 56 18.8/37.6 3.0/1.5 29.0” x 52” x 0.1” 10.5” x 8.5” x 1.4” 5.5 $1,549.00

Portable Power PacksPortable Power Packs are lightweight, foldable power sources for rugged, self-sustaining power. • Suitable for any portable 12V load or 24V above 40 watts • Blocking diodes • Standard 2 prong trailer plug provided • Fold into compact size for easy transport and deployment• Rip stop nylon backing available in Forest or Desert Camo or Forest Green.

Global Solar

P3-108 Portable Power Pack, shown deployed and stowed

Sanyo

Sanyo 167 watt HIT module

895 (35.24)

35 (35.26)

16 (0.63)

107 (0.63)

455 (17.93)

155

(6.1

1)

1320

(52.

0)

212.

5 (8

.37)

330

(13.

0)

212.

5 (8

.37)

330

(13.

0)

Junction Box with wiring (right);Cell structure of HIT solar cell (below)

Negative Positive

Top electrode Amorphous silicon

Single crystallinesiliconAmorphous siliconBottom electrode

Negative Positive

AWG-Conductors x Length For PV module(s) MSRP

MIC #10-2 x 21” US32 $11.25MIC #10-2 x 23” OEM20/40 $11.50MIC #10-2 x 29” SP70/75 $11.75MIC #10-2 x 33” SM110, AP50,110/120, SW85/90/100/115/120 $12.25MIC #10-2 x 35” US42, US64 $12.50MIC #10-2 x 39” SP140/150/Sanyo167/APx130/140 $12.75

Module Interconnects

Module Interconnects – Cable Assemblies (MIC)Module interconnect cables are used to wire modules to adjacent modules. Two conductorcables with #10AWG, red/black insulated, THHN stranded copper wires, can be used for seriesor parallel connection of 12, 24 and 48 VDC systems. Designed for easy installation to alljunction boxes, these cables (rated 90˚C, 600 volt) feature sunlight-resistant, PVC jacketed cablewith two liquid-tight cord connectors for 1/2” NPT openings. The cable jacketing is removed 3”from each end, exposing un-terminated wires. All PV modules (listed below) are designed toaccept bare wire termination. The Shell SP140/150, Sanyo 167 come with MC cables which canbe removed for parallel connection with MIC cables.

MIC Cable Assemblies

MOD

ULES

3/03

Module Interconnects – Liquid Tight Conduit Assemblies (LT)Liquid-tight conduit assemblies provide supplemental protection for individual wiring conductorsbetween adjacent PV modules. In high-voltage installations, they may be required to satisfy theNEC. Standard assemblies include two #10AWG THHN conductors (rated 90˚C, 600 volt),red/black, contained within 1/2” flexible non-metallic conduit with gray PVC straight fittings andlocknuts. The Shell SP140/150, Sanyo 167 come with MC cables which can be removed forparallel connection with LT conduit assemblies.

LT Conduit Assemblies

AWG-Conductors x Length For PV module(s) MSRP

MIC-LT #10-2 x 21” US32 $17.25MIC-LT #10-2 x 23” OEM20/40 $17.50MIC-LT #10-2 x 28” SP70/75 $17.75MIC-LT #10-2 x 33” SM110, AP50,110/120, SW85/90/100/115/120 $18.25MIC-LT #10-2 x 35” US42, US64 $18.75MIC-LT #10-2 x 39” SP140/150/Sanyo167/APx130/140 $19.00

Module Interconnects – MC® Cable Assemblies (Multi-Contact cables)Quality MC cables are assembled with automatic tooling for the highest degree of reliability.Used as module interconnects or output leads, SunWize UL listed MC cables are available withmale or female fittings on one end (specify M or F). Each cable includes MC connector, 1/2”non-metallic cord connector with a #10AWG type ‘USE’ 600 V rated outdoor black wire. Can beinstalled on conventional solar module junction box for ‘plug n play’ interconnection or added tosolar modules with existing MC connectors for extended distances.

MC Cable Assemblies Model Male or Female Length MSRP

MC#10 - 24 M or F 24” $12.25MC#10 - 36 M or F 36” $13.25MC#10 - 48 M or F 48” $13.75MC#10 - 72 M or F 72” $15.75MC#10 - 120 M or F 120” $18.25MC#10 - 240 M or F 240” $24.25MC#10 - 360 M or F 360” $29.25



Module Output CablesModule Output Cables are used for connection from the solar array to the controller or PV combiner assemblies. Cables aresunlight-resistant, PVC tray cable and direct burial with red/black THHN conductors (rated 90˚ C, 600 volt). All are cut to lengthand outfitted with two strain-relief cord connectors for 1/2” NPT, one end terminated for connection into PV junction box, #10AWG with fork terminals, #8-6AWG with copper lugs.

MSRP MSRP MSRP MSRP

AWG-Conductors 10FT 20FT 30FT 50 FT

#10-2 $22.50 $33.25 $41.75 —————-#8-2 $41.50 $58.75 $77.25 $108.00#6-2 $47.50 $63.75 $83.00 $117.00

MODULES

3/03

Solar Modules

Module Output Cables

Solar Module FeaturesSharp’s modules are designed for a variety of electrical power requirements. Based on crystalsilicon solar technology, the modules have superb durability to withstand rigorous operatingconditions. The 123 and 165 watt modules use multi-crystal silicon solar cells and the 175 and185 watt modules use single crystal silicon solar cells. The modules feature bypass diodes tominimize power drop caused by shade and BSF (Black Surface Field) structure to improve cellconversion efficiency. Aluminum frames. All modules are UL listed, include a 51” lead wire with MCconnectors and carry a 25-year warranty.

Sharp

Sharp ND-L3E1U 123W module

Sharp NT-S5E1U 185W module


ND-L3E1U 123 17.2 7.16 21.3 8.12 59.02” x 26.06” 30.87 $799.00NE-Q5E2U 165 34.6 4.77 43.1 5.46 62.00” x 32.52” 37.49 $1079.00NT-R5E1U 175 35.4 4.95 44.4 5.55 62.00” x 32.52” 37.49 $1159.00NT-S5E1U 185 36.2 5.11 44.9 5.75 62.00” x 32.52” 37.49 $1225.00

NE-Q5E2U 165W module

Physical Dimensions in inches

MODEL A B C D E F G H

175/185 62.0 32.5 1.8 30.9 19.1 7.3 30.5 51.1

165 62.0 32.5 1.8 30.9 19.1 7.3 30.5 51.1

123 59.0 26.0 1.8 29.5 n/a 9.8 24.4 51.1

A d v a n c e d E n e r g y G r o u pAEG

A d v a n c e d E n e r g y G r o u pAEG

MOUNTS

3/03

Module Mounts

Universal Side-of-Pole Mount – One Module, AdjustableSingle module side-of-pole mounts are made of 1/8” brushed aluminum and features a moduleclamping method that eliminates any need to drill additional holes. Mounts consist of a polesaddle bracket and a 0 to 90-degree adjustable mounting arm with tilt indicators. Clamps andbracket include captive stainless nuts for easy assembly, stainless bolts and two stainless bandclamps adjustable from 2” to 4” OD poles.

Number of Modules: 1

SunWize®

SW Adjustable SOP Mount

SunWize offers a wide variety of mounting options

Some customers fabricate their own mounts from wood or scrap metal. However, for those who desire documented quality

control, SunWize provides a range of alternatives. They include roof mounts, ground mounts, pole modules (both side-of-pole and

top-of-pole), rail mounts (as in offshore oil rig rails...or porch rails) as well as tracking mounts. Which mounts to choose depends

upon the specific application and customer preferences. Details such as site conditions (e.g. shade, terrain, annual snowfall),

size of the array, and structural considerations determine what products to select.

Once you determine what type of mount, the next question is with what material? Mounts can be fabricated from milled aluminum

(the most popular), anodized aluminum (for applications in highly corrosive climates such as marine environments), painted steel,

galvanized steel, or some combination such as a stainless steel pole collar with milled aluminum module rails.

Mounts are available as fixed racks or as trackers. Fixed racks are stationary. Trackers follow the movement of the sun in order

to improve module output for applications requiring the highest efficiency such as water pumping. There are pros and cons to the

tracking methodology. As with every aspect of your system, it is best to seek the advice of your SunWize dealer.

Module Type Part #

AstroPower AP50 950UNI1LRGKITBShell Solar ST5/ST10 950UNI1SMLKITB Shell Solar ST20/ST40 950UNI1SMLKITB Shell Solar SM50/55 950UNI1SMLKITB Shell Solar SP75 950UNI1LRGKITB

SunWize OEM5 950UNI1SMLKITB

Module Type Part #

SunWize OEM10 950UNI1MEDKITBSunWize OEM20 950UNI1MEDKITBSunWize OEM40 950UNI1MEDKITB

Uni-Solar US11 950UNI1US11Uni-Solar US21 950UNI1MEDKITBUni-Solar US32 950UNI1MEDKITB

11 gauge aluminum mounts are fixed at 45 degrees. Mounting brackets with slotted patternallows for U-bolt attachment to poles from 2” to 4” diameter, and can also be wall or roofmounted. The small mount includes 2” pipe U-bolt, the larger mount includes two stainlessband clamps for 2-4” diameter.

SunWize OEM Module 45˚ Angle Side-of-Pole Mounts – One Module

SW OEM 5 SOP Mount

SW OEM 5 SOP Mount detail

Number of Modules: 1

Module Type Part # MSRP

Uni-Solar US3/5 950SW5/10MTASSY $23.00

Shell Solar ST5/10 950SW5/10MTASSY $23.00

SunWize OEM5 950SW5/10MTASSY $23.00

SunWize OEM20/40 950UNILRGOEM-A $46.00

SW OEM 20/40 SOP Mount

MSRP950UNI1LRGKITB $59.00

950UNI1MEDKITB $55.00

950UNI1SMLKITB $48.00

950UNI1US11 $48.00


MOU

NTS

3/03

Module Mounts

Universal Roof/Ground Mount Support StructuresSunWize Universal roof/ground mount module support structures are engineered to endure theharshest environments. They feature a continuous slotted pattern on heavy gauge brushedaluminum channel supporting members. Three rail sizes, 96-1/4”, 104-1/2” and 118-1/2” long,allow mounting of any large-framed solar module without the need to drill additional holes,including solar modules by other manufacturers not listed in table below. Simply divide the raillength by the width (inches) of the module to determine how many will fit. All can ship UPS (add‘U’ suffix to 118” model).

Flush mount structures (USF) include four mounting feet and all stainless steel fasteners.Adjustable tilt models (USA) incorporate additional dual-telescoping support legs, infinitelyadjustable from 25 to 55 degrees. Our unique captive bolt design in the tilt leg allows for one-handed angle adjustment.

SunWize®

SW Universal Support Structure

FLUSH MOUNTS

# of Modules 3 4 5Module Type

AstroPower AP110/120 950SWUSF-96 950SWUSF-104AstroPower APx130/140 950SWUSF-118Sanyo 167/180 950SWUSF-118 (SY)Sharp 123 950SWUSF-96 950SWUSF-104Sharp 165/185 950SWUSF-104Shell Solar SP70/75 950SWUSF-96 950SWUSF-104Shell Solar SM110 950SWUSF-96 950SWUSF-104Shell Solar SP140/150 950SWUSF-96SunWize SW85/90 950SWUSF-96 950SWUSF-118 SunWize SW100/115/120 950SWUSF-96 950SWUSF-104UniSolar US42/64 950SWUSF-96 950SWUSF-118

ADJUSTABLE MODELS

# of Modules 3 4 5Module Type

AstroPower AP110/120 950SWUSA-96 950SWUSA-104AstroPower APx130/140 950SWUSA-118Sanyo 167/180 950SWUSA-118 (SY)Sharp 123 950SWUSA-96 950SWUSA-104Sharp 165/185 950SWUSA-104Shell Solar SP70/75 950SWUSA-96 950SWUSA-104Shell Solar SM110 950SWUSA-96 950SWUSA-104Shell Solar SP140/150 950SWUSA-96SunWize SW85/90 950SWUSA-96 950SWUSA-118 SunWize SW100/115/120 950SWUSA-96 950SWUSA-104UniSolar US42/64 950SWUSA-96 950SWUSA-118

Flush Mounts MSRP

950SWUSF-96 $139.00

950SWUSF-104 $159.00

950SWUSF-118 $189.00

950SWUSF-118u $199.00

SY versions

950SWUSF-118(SY) $189.00

950SWUSF-118u(SY) $199.00

Aluminum flush mount kits include four “Z” brackets and four stainless steel bolts. Fits all modules.

Model Weight MSRPFlush Mount Kits 0.5 lbs $6.00

Universal Single-Module Flush Mount Kits

SunWize Flush Mount Kits

Adj. Mounts MSRP

950SWUSA-96 $239.00

950SWUSA-104 $259.00

950SWUSA-118 $289.00

950SWUSA-118u $299.00

SY versions

950SWUSA-118(SY) $289.00

950SWUSA-118u(SY) $299.00


MOU

NTS

Module Mounts

Roof/Ground MountsRoof/Ground Mounts resemble an “A” frame and accommodate from 1 to 12 modules. Themounts are perfect for ground, roof and vertical surfaces. Racks with telescoping back legs areadjustable from 20 to 65 degrees. Racks with one piece leg have adjustable points at 30, 45 and 60 degrees. All racks are designed to withstand 30-lb/ft2 windload. Stainless steel modulemounting hardware is provided. Anchor bolts are not included. Standard racks are mill-finishaluminum. For harsh environments, racks are available in anodized aluminum. Available finishesare: Mill Aluminum (MA) and Anodized Aluminum (AA). You must specify which leg you prefer:TL– for telescoping leg or OPL– for a one-piece leg. Prices are for telescoping legs.

Power-Fab Mounts

Power-Fab Roof/Ground Mounts

Solar Module # of Modules Part # MSRP

AstroPower AP50 1 SWRGMAP501 $105.002 SWRGMAP502 $170.003 SWRGMAP503 $205.004 SWRGMAP504 $265.00

AstroPower AP110/120 1 SWRGMAP1101 $100.002 SWRGMAP1102 $165.003 SWRGMAP1103 $205.004 SWRGMAP1104 $290.005* SWRGMAP1105 $340.00

Sharp 123 1 SWRGMSH1231 $115.002 SWRGMSH1232 $180.003 SWRGMSH1233 $240.004 SWRGMSH1234 $315.00

Sharp 165/185 1 SWRGMSH1651 $125.002 SWRGMSH1652 $200.003 SWRGMSH1653 $270.004* SWRGMSH1654 $350.00

Shell ST40, SM50-H/55 1 SWRGMSM551 $90.002 SWRGMSM552 $120.003 SWRGMSM553 $145.004 SWRGMSM554 $180.005 SWRGMSM555 $200.006 SWRGMSM556 $240.008 SWRGMSM558 $320.00

Shell SM110 1 SWRGMSM1101 $115.002 SWRGMSM1102 $180.003 SWRGMSM1103 $240.004 SWRGMSM1104 $315.00

Shell SP70/75 1 SWRGMSP751 $95.002 SWRGMSP752 $145.00


Shell SP70/75 3 SWRGMSP753 $185.004 SWRGMSP754 $250.005 SWRGMSP755 $330.006* SWRGMSP756 $370.00

Shell SP140/150 1 SWRGMSP1401 $125.002 SWRGMSP1402 $200.003 SWRGMSP1403 $270.004 SWRGMSP1404 $350.00

SunWize SW85/90 1 SWRGMSW851 $100.002 SWRGMSW852 $155.003 SWRGMSW853 $195.004 SWRGMSW854 $265.005* SWRGMSW855 $350.00

SunWize SW100/115/120 1 SWRGMSW1151 $105.002 SWRGMSW1152 $175.003 SWRGMSW1153 $215.004 SWRGMSW1154 $305.005* SWRGMSW1155 $360.00

Uni-Solar US32 1 SWRGMUS321 $90.002 SWRGMUS322 $120.003 SWRGMUS323 $155.004 SWRGMUS324 $180.00

Uni-Solar US42 1 SWRGMUS421 $110.002 SWRGMUS422 $175.003 SWRGMUS423 $240.004* SWRGMUS424 $285.00

Uni-Solar US64 1 SWRGMUS641 $120.002 SWRGMUS642 $175.003 SWRGMUS643 $240.004* SWRGMUS644 $330.00

* cannot ship via UPS

SunWize Spotlight

LOCATION:Troy, New York

APPLICATION:Residential power

SYSTEM:5.25 kW PV system

18 3/03


MOUNTS

3/03


AstroPower AP50 6 SWTTRGMAP506 $380.008 SWTTRGMAP508 $405.00

10 SWTTRGMAP5010 $475.00AstroPower AP110/120 6 SWTTRGMAP1106 $390.00

8 SWTTRGMAP1108 $465.0010 SWTTRGMAP11010 $525.00

Sharp 123 6 SWTTRGMSH1236 $410.008 SWTTRGMSH1238 $475.00

Sharp 165/185 6 SWTTRGMSH1656 $505.008* SWTTRGMSH1658 $590.00

10* SWTTRGMSH16510 $680.00Shell SM50-H/55 6 SWTTRGMSM556 $360.00

8 SWTTRGMSM558 $370.0010 SWTTRGMSM5510 $390.0012 SWTTRGMSM5512 $410.00


Shell SM110 6 SWTTRGMSM1106 $410.008 SWTTRGMSM1108 $475.00

Shell SP70/75 6 SWTTRGMSP756 $380.008 SWTTRGMSP758 $405.00

10 SWTTRGMSP7510 $475.0012 SWTTRGMSP7512 $570.00

Shell SP140/150 6 SWTTRGMSP1406 $505.008 SWTTRGMSP1408 $590.00

SunWize SW85/90 6 SWTTRGMSW856 $400.008 SWTTRGMSW858 $425.00

10 SWTTRGMSW8510 $500.00SunWize SW100/115/120 6 SWTTRGMSW1156 $410.00

8 SWTTRGMSW1158 $490.0010 SWTTRGMSW11510 $555.00

Uni-Solar US64 6 SWTTRGMUS646 $465.00

Module Mounts

Low-Profile Roof/Ground MountThe module length is vertical and modules are mounted side by side. Standard finish is MillAluminum. Optional finishes is Anodized Aluminum (AA). You must specify which leg you prefer:TL– for telescoping leg (adjustable from 20 to 65 degrees) or OPL– for a one-piece leg (with adjustment points of 30, 45 and 60 degrees). Prices are fortelescoping legs.

Power-Fab Low-Profile Roof Ground Mount


AstroPower AP50 4 SWLPRGMAP504 $310.006 SWLPRGMAP506 $380.00

AstroPower AP110/120 4 SWLPRGMAP1104 $320.006 SWLPRGMAP1106 $400.008 SWLPRGMAP1108 $470.00

Sharp 123 4 SWLPRGMSH1234 $330.006 SWLPRGMSH1236 $410.00

Sharp 165/185 4 SWLPRGMSH1654 $390.00Shell ST40, SM50-H/55 4 SWLPRGMSM554 $250.00

6 SWLPRGMSM556 $285.008 SWLPRGMSM558 $340.00

Shell SM110 4 SWLPRGMSM1104 $330.006 SWLPRGMSM1106 $410.00


Shell SP70/75 4 SWLPRGMSP754 $310.006 SWLPRGMSP756 $390.008 SWLPRGMSP758 $430.00

Shell SP140/150 4 SWLPRGMSP1404 $390.00SunWize SW85/90 4 SWLPRGMSW854 $325.00

6 SWLPRGMSW856 $410.008 SWLPRGMSW858 $455.00

SunWize SW100/115/120 4 SWLPRGMSW1154 $340.006 SWLPRGMSW1156 $420.008 SWLPRGMSW1158 $495.00

Uni-Solar US32 4 SWLPRGMUS324 $295.00Uni-Solar US42 4 SWLPRGMUS424 $330.00Uni-Solar US64 4 SWLPRGMUS644 $365.00

6 SWLPRGMUS646 $430.00

Power-Fab MountsTwo Tier Roof/Ground MountsTwo rows of modules with module length vertical. Standard finish is Mill Aluminum. Optional finishis: Anodized Aluminum (AA). You must specify which leg you prefer: TL – for telescoping leg orOPL – for a one piece leg–at tilt. Prices are for telescoping legs.

Power-Fab Two-TierRoof/Ground Mount



MOU

NTS

3/03

Module Mounts

Top-of-Pole MountsTop-of-Pole Mounts are designed with a collar ready to be mounted on a pole. The racksaccommodate different size poles and are adjustable for optimal sun angle from 15˚ to 65˚ in 10-degree increments. They can be rotated on the pole for manual tracking. Stainless steelmodule mounting hardware is included. Anchor bolts and poles are not included. Standard rackshave mill-finish aluminum module rails with painted steel pole collar and strong back. Mounts areavailable in galvanized steel and anodized aluminum.

Power-Fab Mounts

Solar # of Pole Part # MSRPModule Modules Size

AstroPower AP50 1 2” SWTPMAP501 $100.002 2” SWTPMAP502 $120.003 2.5” SWTPMAP503 $215.004 3” SWTPMAP504 $270.006 3” SWTPMAP506 $350.008 4” SWTPMAP508 $495.00

AstroPower AP110/120 1 2” SWTPMAP1101 $115.002 2.5” SWTPMAP1102 $210.003 3” SWTPMAP1103 $265.004 4” SWTPMAP1104 $330.006 4” SWTPMAP1106 $420.008 6” SWTPMAP1108 $660.00

10 6” SWTPMAP11010 $760.0012 6” SWTPMAP11012 $850.00

Sharp 123 1 2” SWTPMSH1231 $110.002 2.5” SWTPMSH1232 $215.003 3” SWTPMSH1233 $245.004 4” SWTPMSH1234 $360.006 4” SWTPMSH1236 $470.008 6” SWTPMSH1238 $660.00

10 6” SWTPMSH12310 $800.0012* 6” SWTPMSH12312 $900.00

Sharp 165/185 1 2” SWTPMSH1651 $110.002 3” SWTPMSH1652 $245.004 4” SWTPMSH1654 $420.006 6” SWTPMSH1656 $680.008 6” SWTPMSH1658 $860.00

10* 8” SWTPMSH16510 $1050.0012* 8” SWTPMSH16512 $1250.00

Shell ST40, SM50-H/55 1 2” SWTPMSM551 $100.002 2” SWTPMSM552 $110.003 2” SWTPMSM553 $125.004 2.5” SWTPMSM554 $200.006 3” SWTPMSM556 $245.008 4” SWTPMSM558 $360.00

10 4” SWTPMSM5510 $380.0012 4” SWTPMSM5512 $470.00

Shell SM110 1 2” SWTPMSM1101 $110.002 2.5” SWTPMSM1102 $210.003 3” SWTPMSM1103 $245.004 4” SWTPMSM1104 $360.006 4” SWTPMSM1106 $470.008 6” SWTPMSM1108 $660.00

10 6” SWTPMSM11010 $800.0012* 6” SWTPMSM11012 $880.00


Shell SP70/75 1 2” SWTPMSP751 $110.002 2” SWTPMSP752 $115.003 2.5” SWTPMSP753 $225.004 3” SWTPMSP754 $245.006 4” SWTPMSP756 $370.008 4” SWTPMSP758 $440.0010 6” SWTPMSP7510 $645.0012 6” SWTPMSP7512 $720.00

Shell SP140/150 1 2” SWTPMSP1401 $110.002 3” SWTPMSP1402 $245.004 4” SWTPMSP1404 $420.006 6” SWTPMSP1406 $680.008 6” SWTPMSP1408 $860.0010 8” SWTPMSP14010 $1050.00

SunWize SW85/90 1 2” SWTPMSW851 $115.002 2.5” SWTPMSW852 $210.003 3” SWTPMSW853 $240.004 3” SWTPMSW854 $290.006 4” SWTPMSW856 $400.008 6” SWTPMSW858 $645.00

10* 6” SWTPMSW8510 $695.0012 6” SWTPMSW8512 $760.00

SunWize SW100/115/120 1 2” SWTPMSW1151 $120.002 2.5” SWTPMSW1152 $220.003 3” SWTPMSW1153 $280.004 4” SWTPMSW1154 $350.006* 4” SWTPMSW1156 $440.008 6” SWTPMSW1158 $690.0010 6” SWTPMSW11510 $790.0012 6” SWTPMSW11512 $885.00

Uni-Solar US32 1 2” SWTPMUS321 $100.002 2” SWTPMUS322 $105.003 2” SWTPMUS323 $130.004 2.5” SWTPMUS324 $210.00

Uni-Solar US42 1 2” SWTPMUS421 $110.002 2” SWTPMUS422 $140.004 3” SWTPMUS424 $325.00

Uni-Solar US64 1 2” SWTPMUS641 $115.002 2.5” SWTPMUS642 $210.004 3” SWTPMUS644 $370.006 6” SWTPMUS646 $550.008 6” SWTPMUS648 $710.00

10* 6” SWTPMUS6410 $880.00



MOUNTS

3/03 21

Module Mounts


AstroPower AP50 1 SWSPMAP501 $105.002 SWSPMAP502 $195.003 SWSPMAP503 $245.004 SWSPMAP504 $360.00

AstroPower AP110/120 1 SWSPMAP1101 $175.002 SWSPMAP1102 $240.003 SWSPMAP1103 $330.00

Sharp 123 1 SWSPMSH1231 $165.002 SWSPMSH1232 $220.00

Sharp 165/185 1 SWSPMSH1651 $195.002 SWSPMSH1652 $290.00

Shell ST5/10* 1 SWSPMST101 $65.00(*price is for milled aluminum) 2 SWSPMST102 $135.00Shell ST40, SM50-H/55 1 SWSPMSM551 $95.00

2 SWSPMSM552 $165.003 SWSPMSM553 $185.004 SWSPMSM554 $220.00


Shell SM110 1 SWSPMSM1101 $165.002 SWSPMSM1102 $220.00

Shell SP70/75 1 SWSPMSP751 $100.002 SWSPMSP752 $185.003 SWSPMSP753 $240.004 SWSPMSP754 $290.00

Shell SP140/150 1 SWSPMSP1401 $195.00SunWize SW85/90 1 SWSPMSW851 $170.00

2 SWSPMSW852 $225.003 SWSPMSW853 $315.00

SunWize SW100/115/120 1 SWSPMSW1151 $185.002 SWSPMSW1152 $250.003 SWSPMSW1153 $345.00

Uni-Solar US32 1 SWSPMUS321 $95.002 SWSPMUS322 $165.00



Side-of-Pole MountsSide-of-Pole Mounts are mounted to the pole with either hose clamps or U-bolts (not provided).The racks accommodate different sized poles and are adjustable for optimal sun angle from 15˚ to65˚ in 10-degree increments. Pole size is determined by the number of modules to be mounted.Stainless steel module mounting hardware is included. Anchor bolts and poles are not included.Standard racks are available in both painted steel and mill-finish aluminum. For harsh environmentsracks are available in galvanized steel and anodized aluminum. Available finishes are: Mill Aluminum(MA), Anodized Aluminum (AA), Hot-Dip Galvanized Steel (GS) and Painted Steel (PS). All mountscome with adjustable band clamps for 3” to 5” poles. Pricing is for Painted Steel.

Power-Fab Side-of-Pole Mounts

Power-Fab Mounts

Uni-Rac U-PS Mount

Side-of-Pole MountsUniRac mounting structures incorporate a slotted mounting pattern that fits most PV modules onthe market and are manufactured of mill finish aluminum to withstand corrosion. • 120 mph wind load design • PV module mounting hardware and U-Bolts for pole mounting areincluded • Stainless steel hardware • 1-year limited warranty • Adjustable tilt 15˚ to 60˚

UNI-RAC™


AstroPower AP110/120 1 2.5” U-PS/26M $137.002 3” U-PS/52M $225.003 4” U-PS/80M $270.00

Sharp 123 1 2.5” U-PS/30XXL $156.002 3” U-PS/60XL $255.003 4” U-PS/80XL $290.00

Sharp 165/185 1 2.5” U-PS/32M $152.002 4” U-PS/72M $250.00

Shell SM110 1 2.5” U-PS/26M $137.002 3” U-PS/52M $225.003 4” U-PS/80M $270.00

Shell SP70/75 1 2.5” U-11/24M $106.002 2.5” U-PS/44M $184.003 3” U-PS/64M $240.004 4” U-PS/84M $280.00

Shell SP140/150 1 2.5” U-PS/32M $152.002 3” U-PS/64M $240.00


SunWize OEM5 2 2.5” U-11/20M $103.00SunWize OEM10 2 2.5” U-PS/32M $152.00SunWize OEM20/40 2 2.5” U-PS/36M $163.00

4 4” U-PS/72M $250.00SunWize SW85/90 1 2.5” U-11/24L $113.00

2 3” U-PS/52L $235.003 4” U-PS/80L $280.004 4” U-PS/96L $320.00

SunWize SW100/115/120 1 2.5” U-PS/26XXL $146.002 3” U-PS/52L $235.003 4” U-PS/80L $280.00

Uni-Solar US32 2 2.5” U-PS/32XL $158.00Uni-Solar US42 2 3” U-PS/60M $235.00

3 4” U-PS/88L $300.00Uni-Solar US64 1 2.5” U-PS/30XL $153.00

2 3” U-PS/60L $245.003 4” U-PS/88L $300.00


MOU

NTS

3/03

Module Mounts

SolarMount Universal Roof Mounts - Top DownSolarMounts offer an easy, fast and safe way to install a PV array on the roof of any building.• Top down clamps for framed PV modules. • Rooftop Assembly – An entire array can be fullyinstalled and wired on the roof 1 module at a time. • Easy Installation – Continuous, slotted railsprovide infinite adjustability for captive bolt positioning. • Bi-directional Mounting – Mount moduleshorizontally or vertically or use both orientations in limited space situations. • Meet Building CodeRequirements – SolarMounts securely attach the array to the roof in compliance with U.S. BuildingCodes. • SM108 and larger are usually shipped via Motor Freight due to their length. There is anadditional charge to ship model #’s SMR120 through SMR204 via UPS. Rails are cut in half. Orderthe cut and splice kit to ship UPS – #963UNIUPS-20 – MSRP-$20.00.

UNI-RAC™

Uni-Rac SolarMount

Solar # of OrderModule Modules Rail# – Clamp#

AstroPower AP110/120 2 SMR60-CT2C3 SMR84-CT3C4 SMR120-CT4C5 SMR144-CT5C6 SMR168-CT6C7 SMR192-CT7C

AstroPower APx130/140 2 SMR84-CT2C3 SMR120-CT3C4 SMR144-CT4C5 SMR180-CT5C

Sanyo 167/180 2 SMR84-C2S3 SMR108-C3S4 SMR144-C4S5 SMR180-C5S

Sharp 123 2 SMR60-CT2F3 SMR84-CT3F4 SMR120-CT4F5 SMR144-CT5F6 SMR168-CT6F7 SMR192-CT7F

Sharp 165/185 2 SMR72-CT2F3 SMR106-CT3F4 SMR144-CT4F5 SMR180-CT5F6 SMR204-CT6F

Shell SM110 2 SMR60-CT2D3 SMR84-CT3D4 SMR120-CT4D5 SMR144-CT5D6 SMR168-CT6D7 SMR192-CT7D

Shell SP70/75 2 SMR48-CT2C3 SMR72-CT3C

Solar # of OrderModule Modules Rail# – Clamp#

Shell SP70/75 4 SMR96-CT4C5 SMR120-CT5C6 SMR144-CT6C7 SMR156-CT7C8 SMR180-CT8C

Shell SP140/150 2 SMR72-CT2D3 SMR106-CT3D4 SMR144-CT4D5 SMR168-CT5D6 SMR204-CT6D

SunWize SW85/90 2 SMR60-CT2C3 SMR84-CT3C4 SMR106-CT4C5 SMR132-CT5C6 SMR156-CT6C7 SMR180-CT7C8 SMR204-CT8C

SunWize SW100/115/120 2 SMR60-CT2C3 SMR84-CT3C4 SMR120-CT4C5 SMR144-CT5C6 SMR168-CT6C7 SMR192-CT7C

Uni-Solar US64 2 SMR72-CT2B3 SMR96-CT3B4 SMR132-CT4B5 SMR156-CT5B6 SMR192-CT6B

Uni-Solar US116 2 SMR72-CT2E3 SMR96-CT3E4 SMR132-CT4E5 SMR168-CT5E6 SMR192-CT6E

Rails - includes 2 rails, L-feetand hardwareModel # of L-feet MSRPSMR48 4 $83.00SMR60 4 $99.00SMR72 4 $115.00SMR84 4 $131.00SMR96 4 $145.00SMR106 4 $157.00SMR108 4 $157.00SMR120 6 $178.00

Model # of L-feet MSRPSMR132 6 $190.00SMR144 6 $202.00SMR156 6 $214.00SMR168 6 $226.00SMR180 6 $238.00SMR192 8 $259.00SMR204 8 $271.00

Top Mounting Clamp Sets

CT2A through F $16.00

Model MSRPCT3A through F $20.00CT4A through F $24.00CT5A through F $28.00CT6A through F $32.00CT7A through F $36.00CT8A through F $40.00C2S $16.00C3S $20.00C4S $24.00C5S $28.00

Bottom Mounting Clamp Sets

Model MSRPCB2 $14.00CB3 $18.00CB4 $22.00CB5 $26.00CB6 $30.00CB7 $34.00CB8 $38.00


MOUNTS

3/03

SolarMount Tilt Leg KitsTilt Leg Kits are used to tilt the array to a more optimum angle to enhance overall systemperformance. These kits feature a quick locking adjustment that makes even seasonaladjustments fast and easy.

Low Profile Adjustable Tilt LegsUse the chart below to select the Low Profile Tilt Leg kit required for your modules. Total tilt legs(not kits) must equal half the total number of L-feet in your installation.

Low Profile Tilt Leg Sizing Chart (Tilt Angle Range in Degrees)

Module TLL2-12 or TLL3-12 TLL2-30 or TLL3-30 TLL2-44 or TLL3-44

AstroPower AP110/120 7-17 17-43 25-60+AstroPower APx130/140 5-13 13-32 19-49Sanyo 167/180 8-19 19-49 28-60+Sharp 123 7-16 17-43 25-60+Sharp 165/185 7-16 16-40 24-60+Shell SM110 8-19 19-48 28-60+Shell SP70/75 9-20 21-54 31-60+Shell SP140/150 7-15 16-39 23-60SunWize SW85/90/100/115/120 8-17 18-44 26-60+Uni-Solar US64 8-18 19-47 27-60+Uni-Solar US116 4-10 10-26 15-39

High Profile Adjustable Tilt Legs

Use the chart below to select the High Profile Tilt Leg Kit required for your rail sets. Order oneTLH Tilt Leg Kit for each rail set. TLH2 kits have 2 legs per kit; TLH4 kits have 4 legs per kit.

High Profile Tilt Leg Sizing Chart

Module Mounts

Uni-Rac Standoff

SolarMount AccessoriesRaised flange Standoff used for flashed, roof-mounted installations. Weight MSRP

STR3 1 each 3 inch standoff and fasteners 2 lbs. $18.00STR6 1 each 6 inch standoff and fasteners 2 lbs. $19.00963ACC001 No caulk roof flashing $ 9.00SP2 Splice Kits Required if two rail sets are spliced together. $16.00

Kit contains 2 each rail splices and fasteners

UNI-RAC™

Low Profile Kits

Legs Model per Kit MSRP

TLL2-12 2 $49.00

TLL2-30 2 $59.00

TLL2-44 2 $67.00

TLL3-12 3 $68.00

TLL3-30 3 $83.00

TLL3-44 3 $94.00

Rail Set TLH2-12 TLH2-44 TLH2-72

SMR48 9-21 31-60+ NASMR60 7-17 24-60+ 40-60+SMR72 6-14 20-54 33-60+SMR84 5-12 17-46 28-60+SMR96 4-10 15-40 24-60+SMR106 4-9 13-36 22-60+

Rail Set TLH4-18 TLH4-64 TLH4-104

SMR120 5-10 17-38 27-60+SMR132 4-9 15-35 24-59SMR144 4-8 14-32 22-53SMR156 4-8 13-29 20-49SMR168 3-7 12-27 19-45SMR180 3-7 11-25 18-42SMR192-216 Not recommended

High Profile Kits

Legs Model per Kit MSRP

TLH2-12 2 $37.00

TLH2-44 2 $54.00

TLH2-72 2 $68.00

TLH4-18 4 $65.00

TLH4-64 4 $99.00

TLH4-104 4 $129.00

# of Modules: 1Solar Module: Mounting Rack Model # MSRP

AstroPower AP110/120 U-RV/28 $70.00Sharp 123 U-RV/28 $70.00Sharp 165/185 U-RV/36 $80.00Shell SM110 U-RV/28 $70.00Shell SP70/75 U-RV/24 $65.00Shell SP140/150 U-RV/32 $75.00SunWize SW85/90 U-RV/24 $65.00SunWize SW100/115/120 U-RV/28 $70.00UniSolar US42 & US64 U-RV/32 $75.00

U-RV Mounts – Mounts designed to fold flat or tilt-up for RV rooftops.

Uni-Rac Splice Kit

Uni-Rac U-RV Mount



MOUNTS

3/03

Module Mounts


AstroPower AP50 1 SWSPMAP501 $105.002 SWSPMAP502 $195.003 SWSPMAP503 $245.004 SWSPMAP504 $360.00

AstroPower AP110/120 1 SWSPMAP1101 $175.002 SWSPMAP1102 $240.003 SWSPMAP1103 $330.00

Sharp 123 1 SWSPMSH1231 $165.002 SWSPMSH1232 $220.00

Sharp 165/185 1 SWSPMSH1651 $195.002 SWSPMSH1652 $290.00

Shell ST5/10* 1 SWSPMST101 $65.00(*price is for milled aluminum) 2 SWSPMST102 $135.00Shell ST40, SM50-H/55 1 SWSPMSM551 $95.00

2 SWSPMSM552 $165.003 SWSPMSM553 $185.004 SWSPMSM554 $220.00


Shell SM110 1 SWSPMSM1101 $165.002 SWSPMSM1102 $220.00

Shell SP70/75 1 SWSPMSP751 $100.002 SWSPMSP752 $185.003 SWSPMSP753 $240.004 SWSPMSP754 $290.00

Shell SP140/150 1 SWSPMSP1401 $195.00SunWize SW85/90 1 SWSPMSW851 $170.00

2 SWSPMSW852 $225.003 SWSPMSW853 $315.00

SunWize SW100/115/120 1 SWSPMSW1151 $185.002 SWSPMSW1152 $250.003 SWSPMSW1153 $345.00




Side-of-Pole MountsSide-of-Pole Mounts are mounted to the pole with either hose clamps or U-bolts (not provided).The racks accommodate different sized poles and are adjustable for optimal sun angle from 15˚ to65˚ in 10-degree increments. Pole size is determined by the number of modules to be mounted.Stainless steel module mounting hardware is included. Anchor bolts and poles are not included.Standard racks are available in both painted steel and mill-finish aluminum. For harsh environmentsracks are available in galvanized steel and anodized aluminum. Available finishes are: Mill Aluminum(MA), Anodized Aluminum (AA), Hot-Dip Galvanized Steel (GS) and Painted Steel (PS). All mountscome with adjustable band clamps for 3” to 5” poles. Pricing is for Painted Steel.

Power-Fab Side-of-Pole Mounts

Power-Fab Mounts

Uni-Rac U-PS Mount

Side-of-Pole MountsUniRac mounting structures incorporate a slotted mounting pattern that fits most PV modules onthe market and are manufactured of mill finish aluminum to withstand corrosion. • 120 mph wind load design • PV module mounting hardware and U-Bolts for pole mounting areincluded • Stainless steel hardware • 1-year limited warranty • Adjustable tilt 15˚ to 60˚

UNI-RAC™


AstroPower AP110/120 1 2.5” U-PS/26M $137.002 3” U-PS/52M $225.003 4” U-PS/80M $270.00

Sharp 123 1 2.5” U-PS/30XXL $156.002 3” U-PS/60XL $255.003 4” U-PS/80XL $290.00

Sharp 165/185 1 2.5” U-PS/32M $152.002 4” U-PS/72M $250.00

Shell SM110 1 2.5” U-PS/26M $137.002 3” U-PS/52M $225.003 4” U-PS/80M $270.00

Shell SP70/75 1 2.5” U-11/24M $106.002 2.5” U-PS/44M $184.003 3” U-PS/64M $240.004 4” U-PS/84M $280.00

Shell SP140/150 1 2.5” U-PS/32M $152.002 3” U-PS/64M $240.00


SunWize OEM5 2 2.5” U-11/20M $103.00SunWize OEM10 2 2.5” U-PS/32M $152.00SunWize OEM20/40 2 2.5” U-PS/36M $163.00

4 4” U-PS/72M $250.00SunWize SW85/90 1 2.5” U-11/24L $113.00

2 3” U-PS/52L $235.003 4” U-PS/80L $280.004 4” U-PS/96L $320.00

SunWize SW100/115/120 1 2.5” U-PS/26XXL $146.002 3” U-PS/52L $235.003 4” U-PS/80L $280.00

Uni-Solar US32 2 2.5” U-PS/32XL $158.00Uni-Solar US42 2 3” U-PS/60M $235.00

3 4” U-PS/88L $300.00Uni-Solar US64 1 2.5” U-PS/30XL $153.00

2 3” U-PS/60L $245.003 4” U-PS/88L $300.00

MOUNTS

3/03

Module Mounts

TrackRack™Tracking can increase electrical output of modules by 25% over that of a fixed rack. The sun’s heatmoves liquid from side to side, allowing gravity to turn the Track Rack and follow the sun. Nomoving parts to wear out or consume energy. The racks are ideal for applications such as waterpumping where constant power levels enhance system output. The UTR comes in five standardsizes for holding 2 to 14 modules and accommodates most PV modules. The Zomeworks J Clip™universal stainless steel, module-mounting clip eliminates the need for module-specific holes andincreases the flexibility of each rack model. The J-Clip allows you to change the module makeand size without purchasing a new rack, in most instances. All Zomeworks racks are guaranteedfor 10 years. Extra Clip Pack available – SW Part# UTRXCLI – MSRP $8.00.

UTR020 UTR040 UTRF64 UTRF90 UTRF120

Mounting Pole Diameter: 2.5” 3” 6” 6” 6”

MSRP $490.00 $860.00 $1320.00 $1493.00 $1686.00

ZOMEWORKS

Zomeworks TrackRack

Solar Module # of Modules Part #

AstroPower AP110/120 1 UTR0202 UTR0204 UTR0406 UTRF64*8 UTRF90

10 UTRF12012 UTRF120

Sanyo 167/180 1 UTR0202 UTR0404 UTRF646 UTRF908 UTRF120

Sharp 123 1 UTR0202 UTR0204 UTR0406 UTRF64*8 UTRF90

10 UTRF120Sharp 165/185 1 UTR020

2 UTR0404 UTRF906 UTRF908 UTRF120

ShellSM50-H/55 1 UTR0202 UTR0204 UTR0206 UTR0408 UTR040

10 UTRF6412 UTRF6414 UTRF64

Shell SM110 1 UTR0202 UTR0204 UTR0406 UTRF648 UTRF90


Shell SP70/75 1 UTR0202 UTR0204 UTR0406 UTRF648 UTRF64

Solar Module # of Modules Part #

Shell SP70/75 10 UTRF9012 UTRF9014 UTRF120

Shell SP140/150 1 UTR0202 UTR0404 UTRF646 UTRF908 UTRF120

SunWize SW85/90 1 UTR0202 UTR0204 UTR0406 UTRF64*8 UTRF90

10 UTRF9012 UTRF120

SunWize SW100/115/120 1 UTR0202 UTR0204 UTR0406 UTRF648 UTRF90


Uni-Solar US32 1 UTR0202 UTR0206 UTR0408 UTRF90

10 UTRF9012 UTRF9014 UTRF90

Uni-Solar US42 1 UTR0202 UTR0204 UTR0406 UTRF648 UTRF64

10 UTRF9012 UTRF90*14 UTRF120*

Uni-Solar US64 1 UTR0202 UTR0204 UTR0406 UTRF908 UTRF90

10 UTRF120

* extra set of rails required – MSRP $200.00



CONT

ROLL

ERS

Controllers

24 3/03

Solar Controller or Regulator

Once the solar modules are selected, wired together and mounted, it is time to get the energy produced by the modules safelyto the battery. The basic function of the charge controller is to keep the batteries from overcharging. This can occur if the solararray is producing even a small percentage of their rated power while the batteries are at or near full charge. If you keeppumping solar current into a full battery bank you will shorten its life. This can be significant if using sealed, maintenance freebatteries. If using flooded batteries, overcharging increases system maintenance. A good quality charge controller is essential toensure the integrity of a well-designed system.

Charge controllers can be as simple as “over-charge” protection or they can be fully automated offering low voltage alarms andremote reporting functions. Temperature compensation is one feature available on even the most basic of controllers and is highlyrecommended. Batteries and PV modules behave differently under different temperature conditions. Temperature compensationwill modify the solar charging current in response to battery temperature. A warm battery experiences faster chemical reactionsand therefore needs less voltage and current to fully charge. A cold battery needs more robust charging since cold temperaturesrob a battery of its capacity. We offer many types of charge controllers such as solid state shunt, series relay, pulse widthmodulated as well as the newest in the field, maximum power point tracking (MPPT). In order to choose the best charge controlscheme and hardware for your system it is good to do your homework and then discuss the choices with your dealer. The dealerwill combine his expertise of the technology with the information about your particular application and situation.

SW-IL6 Charge RegulatorThe SW-IL6 battery charge regulator is designed for 12-volt PV systems rated up to 100 watts. Thissmall regulator package fits into the junction box of most solar modules. The waterproof assemblyis encapsulated within a black ABS plastic shell with 4” lead wires. A pressure sensitive adhesivestrip is supplied for mounting. Designed to mount in the module junction box, the output cablefrom the charge regulator should be a minimum of #14 AWG up to 15 feet. For a greater distancesee the Wiring Reference Guide on page 78. Can also be installed on the battery. Featurestransient surge protection, Multi-function green LED indicator, reverse polarity protection,operating temperature: -35ºC to + 75ºC, temperature compensation, dual comparator - PWMcharging algorithm, self-consumption 4 ma., fixed 14.2 VDC. One-year warranty.

SunWize®

Other Features Include:

• Automatically adjusts for 12 V or 24 V system• Operating temperature range is -25° C to +40° C• World Bank and CE certified

• Temperature compensated overcharge and overdischargeprotection

• Protection against over temperature, battery overvoltage,module overcurrent, and load overcurrent

Model Voltage Rated PV Rated Load Dimensions Unit Current Current Weight MSRP

Solsum 5.0X 12/24 VDC 5 amps N/A 3.4” x 3.85” x 1.37” .22 lb. $39.00

Solsum 6.6X LVD 12/24 VDC 6 amps 6 amps 3.4” x 3.85” x 1.37” .22 lb. $49.00



SunWize Solsum ControllerThe SunWize-Steca Solsum Controller is an economical pulse-width modulated shunt controllerdesigned for small and mid-sized systems. Using the most up-to-date and innovativetechnology, the Solsum controllers fulfill the task of overcharge and over discharge protection. The overcharge protection operates as a pulse-width-modulated shunt controller and guaranteesfaster charging of the battery. A tri-color LED indicates three ranges of battery voltage and agreen LED indicates array current. These controllers include temperature compensated charging,MOSFET transistors and fuse protection. Solsum Controllers, certified for World Bank projects,ensure maintenance-free operation and long product life. One-year warranty.

SunWize Solsum Controller

Model Voltage Rated PV Current Dimensions Unit Weight MSRP

SW-IL6 12V 6 amps 1.25” x 1.5” x .40” 2.0 oz. $42.00

SunWize SW-IL6

CONTROLLERS

3/03

Controllers

SunWize Steca ControllerThe SunWize-Steca controller uses an advanced control algorithm that sets new standards forsolar charge technology. The state-of-charge algorithm combines battery temperature, batteryvoltage, and load discharge rate to determine the true battery SOC. The controller’s memory ofdischarge patterns enables the controller to know the degree of battery sulfation. This allowseven greater accuracy towards determining true battery SOC. The self-learning controller auto-matically adjusts for the capacity and age of the battery. The resultant battery SOC is displayedwithin a 10% accuracy range. The patented hybrid regulator design combines both series andshunt technology for nominal power consumption. Maximum wire gauge for terminal: 4 AWG.

The Tarom features adjustable set points that are stored in the controller's memory. AvailableTarom options are an external data logger, external shunts for measuring current and a remotetemperature sensor. Other options include control modules that load shed or PV shed based onthe battery SOC that is communicated with the controller over a DC databus. Two-year warranty.

SunWize®

SunWize Steca Controller

Model Voltage Rated Rated Dimensions Unit WeightPV Current Load Current (lbs.) MSRP

Alpha 12/24VDC 8 amps 8 amps 7.4" x 4" x 1.93" 1 $82.00

Alpha with LCD 12/24VDC 8 amps 8 amps 7.4" x 4" x 1.93" 1 $136.00

Gamma 12/24VDC 12 amps 12 amps 7.4" x 4" x 1.93" 1 $99.00

Gamma with LCD 12/24VDC 12 amps 12 amps 7.4" x 4" x 1.93" 1 $150.00

Sigma 12/24VDC 20 amps 20 amps 7.4" x 4" x 1.93" 1 $119.00

Sigma with LCD 12/24VDC 20 amps 20 amps 7.4" x 4" x 1.93" 1 $175.00

Omega 12/24VDC 30 amps 30 amps 7.4" x 4" x 1.93" 1 $150.00

Omega with LCD 12/24VDC 30 amps 30 amps 7.4" x 4" x 1.93" 1 $209.00

Tarom 235 12/24 VDC 35 amps 35 amps 7.4" x 4" x 1.93" 1 $319.00

Tarom 245 12/24VDC 45 amps 45 amps 7.4" x 4" x 1.93" 1 $369.00

Tarom 430 48VDC 30 amps 30 amps 7.4" x 4" x 1.93" 1 $425.00

• LCD display • Audible buzzer fault condition warning alarm

(not available with the LCD display)

• Opto-isolated fault condition warning alarm that can beconnected to any analog input monitoring device (notavailable with the LCD display)

Options:

SunWize-Steca and Solsum Controller Operational SettingsSunWize-Steca SunWize-Steca Solsum

Set point values based on: SOC algorithm Battery Voltage Battery Voltage

Load Disconnect Prewarning SOC < 40% 11.7 Volts NONE

Low Voltage Disconnect (LVD) SOC < 30% 11.1 Volts 11.1 Volts

Reconnection of Load after an LVD SOC > 50% 12.6 Volts 12.6 Volts

Equalization Charge* of 14.7 V occurs after SOC < 40% 11.7 Volts 12.4 Volts

Cycle Charge of 14.4 V occurs after SOC < 70% 12.4 Volts 12.4 Volts

Final Charge Voltage 13.7 Volts 13.7 Volts 13.7 Volts

Temperature Compensation -4mV/K/Cell -4mV/K/Cel -4mV/K/Cell

Voltage Values are doubled for 24 V systems* Not applicable to sealed gel or AGM batteries, equalization charge of 14.4 volts for Solsum controllers

Other Features Include:• TUV and UL recognized component • Automatically adjusts for 12 V or 24 V system• Automatic battery equalization can be disabled when

using gel or AGM type lead-acid batteries• Protection against over temperature, battery overvoltage,

module overcurrent, and load overcurrent• Low voltage disconnect and a low voltage warning

• Tricolor information LED and tricolor “SOC” LEDannunciating controller status, errors, and battery SOC

• IP 22 (NEMA 12) protection

• Operating temperature range is -25° C to +50° C

• Manual setting to override the SOC algorithm to allowSOC to be determined by temperature compensatedvoltage levels. This is useful when other loads areconnected directly to the battery.



CONT

ROLL

ERS

Controllers

3/03

Solar Controller or Regulator

Once the solar modules are selected, wired together and mounted, it is time to get the energy produced by the modules safelyto the battery. The basic function of the charge controller is to keep the batteries from overcharging. This can occur if the solararray is producing even a small percentage of their rated power while the batteries are at or near full charge. If you keeppumping solar current into a full battery bank you will shorten its life. This can be significant if using sealed, maintenance freebatteries. If using flooded batteries, overcharging increases system maintenance. A good quality charge controller is essential toensure the integrity of a well-designed system.

Charge controllers can be as simple as “over-charge” protection or they can be fully automated offering low voltage alarms andremote reporting functions. Temperature compensation is one feature available on even the most basic of controllers and is highlyrecommended. Batteries and PV modules behave differently under different temperature conditions. Temperature compensationwill modify the solar charging current in response to battery temperature. A warm battery experiences faster chemical reactionsand therefore needs less voltage and current to fully charge. A cold battery needs more robust charging since cold temperaturesrob a battery of its capacity. We offer many types of charge controllers such as solid state shunt, series relay, pulse widthmodulated as well as the newest in the field, maximum power point tracking (MPPT). In order to choose the best charge controlscheme and hardware for your system it is good to do your homework and then discuss the choices with your dealer. The dealerwill combine his expertise of the technology with the information about your particular application and situation.

SW-IL6 Charge RegulatorThe SW-IL6 battery charge regulator is designed for 12-volt PV systems rated up to 100 watts. Thissmall regulator package fits into the junction box of most solar modules. The waterproof assemblyis encapsulated within a black ABS plastic shell with 4” lead wires. A pressure sensitive adhesivestrip is supplied for mounting. Designed to mount in the module junction box, the output cablefrom the charge regulator should be a minimum of #14 AWG up to 15 feet. For a greater distancesee the Wiring Reference Guide on page 78. Can also be installed on the battery. Featurestransient surge protection, Multi-function green LED indicator, reverse polarity protection,operating temperature: -35ºC to + 75ºC, temperature compensation, dual comparator - PWMcharging algorithm, self-consumption 4 ma., fixed 14.2 VDC. One-year warranty.

SunWize®

Other Features Include:

• Automatically adjusts for 12 V or 24 V system• Operating temperature range is -25° C to +40° C• World Bank and CE certified

• Temperature compensated overcharge and overdischargeprotection

• Protection against over temperature, battery overvoltage,module overcurrent, and load overcurrent

Model Voltage Rated PV Rated Load Dimensions Unit Current Current Weight MSRP





SunWize Solsum ControllerThe SunWize-Steca Solsum Controller is an economical pulse-width modulated shunt controllerdesigned for small and mid-sized systems. Using the most up-to-date and innovativetechnology, the Solsum controllers fulfill the task of overcharge and over discharge protection. The overcharge protection operates as a pulse-width-modulated shunt controller and guaranteesfaster charging of the battery. A tri-color LED indicates three ranges of battery voltage and agreen LED indicates array current. These controllers include temperature compensated charging,MOSFET transistors and fuse protection. Solsum Controllers, certified for World Bank projects,ensure maintenance-free operation and long product life. One-year warranty.

SunWize Solsum Controller


SW-IL6 12V 6 amps 1.25” x 1.5” x .40” 2.0 oz. $42.00

SunWize SW-IL6

CONT

ROLL

ERS

Controllers

3/03

Model/ Voltage Rated Rated Dimensions Unit Weight Description PV Current Load Current (oz.) MSRP

PS 15 12/24V 15 amps 15 amps 6.01” x 4.14” 12 $112.00PS 15M (w/meter) 12/24V 15 amps 15 amps 6.01” x 4.14” 12 $179.00PS 15M-48V 48V 15 amps 15 amps 6.01” x 4.14” 12 $222.00PS 15M-48V-PG 48V 15 amps 15 amps 6.01” x 4.14” 12 $239.00PS 30 12/24V 30 amps 30 amps 6.01” x 4.14” 12 $152.00PS 30M 12/24V 30 amps 30 amps 6.01” x 4.14” 12 $219.00PS 30M-PG 12/24V 30 amps 30 amps 6.01” x 4.14” 12 $236.00Accessories:Remote Temperature SensorThe temperature sensor provides accurate battery charging where the controller and the battery experience different ambient temperatures. For maximum environmental protection, the sensor is encapsulated in epoxy inside a stainless steel housing. The RTP is easily installed by soldering 2 wires to the circuit board. Corrects fortemperatures from -30ºC (-22ºF) to +80ºC (+176ºF). Five-year warranty. 25 ft cable $32.00

ProStar Controller

ProStar ControllerThe ProStar features highly accurate set points, low voltage drops, and sealed & flooded controlparameters. Self-diagnostic testing provides assurance the controller is working correctly orindicates a fault is present. The self-diagnostics plus the currents displayed in the digital meter willprovide a comprehensive test of the controller. The ProStar’s constant voltage PWM regulation uses4 stages of charging including boost charging. Battery type selections are made via rotary switchand include gel, sealed or flooded. ProStar provides higher charging efficiency, increases thebattery capacity, reduces water loss, and extends the life of the battery. Five-year limited warranty.

Morningstar

• Low voltage disconnect• Operating temperatures of -40˚C to +85˚C• PWM battery charging

• Automatic equalization of wet batteries• PG models are positive ground• Temperature compensation

Features:

Morningstar - SunSaverSunSaver’s battery charging design closely copies the ProStar’s advanced charging algorithm.The series PWM algorithm is very stable, yet responds instantly to changing conditions. Theconstant voltage PWM charging is a proven advancement compared to the common on/off PVregulators. Five-year limited warranty. L models include Low Voltage Disconnect.

SunSaver

Model/Description

SS6-12 SS6L-12 SS10-12 SS10L-12SS10L-24SS20L-12SS20L-24

MSRP$48.00$59.00$55.00$70.00$76.00$95.00

$101.00

Dimensions6.0” x 2.2”6.0” x 2.2”6.0” x 2.2”6.0” x 2.2”6.0” x 2.2”6.0” x 2.2”6.0” x 2.2”

Unit Weight(oz.)

8888888

Voltage12V12V12V12V24V12V24V

RatedPV Current6.5 amps6.5 amps10 amps10 amps10 amps20 amps20 amps

RatedLoad Current

N/A6.0 amps

N/A10 amps10 amps20 amps20 amps

Features:• True 0-100% PWM duty cycle• Field selectable for sealed or flooded battery• Temperature compensation• Series design for constant voltage charging

• Pulse charging• Approved for use in hazardous

(Class 1, Div 2, groups A,B,C,D) locations• UL1604 listed and CSA 22.2 (Canada)• Operating temperatures of -40˚C to +85˚C


CONTROLLERS

3/03

Controllers

SunGuard-4The SunGuard is an economical controller that uses the same charging circuit as the SunSavercontroller. It offers true 0-100% PWM duty cycle and setpoint accuracy to 60mV. The SunGuardis fully encapsulated in epoxy potting and has an ABS plastic, impact-resistant case. Five-yearlimited warranty.

Morningstar

SunGuard-4

Model Voltage Rated PV Current Rated Load Current Dimensions Unit Weight MSRP

SL 10-12 12V 10 amps 10 amps 6” x 2.18” x 1.32” 9 oz $108.00SL 10-24 24V 10 amps 10 amps 6” x 2.18” x 1.32” 9 oz $116.00SL 20-12 12V 20 amps 20 amps 6” x 2.18” x 1.32” 9 oz $141.00SL 20-24 24V 20 amps 20 amps 6” x 2.18” x 1.32” 9 oz $148.00


SunGuard4 12V 4.5 amps 2” x 2.5” x 1.5” 3 oz. $30.00

Features:• Sealed/flooded battery select• Temperature compensation

• Parallel operation compatible• Adjustable 2-10 hours, 4 + 2, 6 + 2 or dusk

to dawn

TriStar ControllerThe TriStar is a three-function controller providing reliable solar battery charging, load control ordiversion regulation. This controller operates in only one of these modes at a time but two ormore controllers may be used to provide multiple functions. The digital meter option displaysself-test results, system information and controller setpoints. Remote temperature sensor optionrated from -30ºC (-22ºF) to +80ºC (+176ºF). White power-coated steel, indoor rated, verticalmounting enclosure. UL listed. Five-year warranty.

Features:• Standard model switch selectable for 12/24V or 48V battery• Choice of 7 regulation or LVD setpoints • Conduit-ready enclosure for large wire sizes• RS-232 comm port provides custom setpoints • Self test runs continuously

Charge Controller Mode: • Temperature compensation• PWM may be changed to “on-off” controller to minimize any possible telecom noiseLoad Control Mode: • Starts all loads including inductive• Short circuit and overload protection with automatic reconnectDiversion Control Mode: • May be used for solar, wind or hydroelectric

TriStar

Features:• Temperature compensation • Series design• Lightning protected • No need to derate

• Outdoor rated• Operating temperatures of -40˚C to +85˚C

Rated Rated UnitModel/Description Voltage PV Current Load Current Dimensions Weight MSRP

TS-45 12/24/48V 45 amps 45 amps 10.1” x 4.9” x 2.3” 4 lbs $169.00TS-60 12/24/48V 60 amps 60 amps 10.1” x 4.9” x 2.3” 4 lbs $219.00

TS Digital Meter $99.00TS Remote Digital Meter $136.00Remote Temperature Sensor $32.00

SunLIghtThe SunLight solar lighting controller combines the SunSaver PWM battery charging circuit with amicrocontroller for automatic lighting functions. The SunLight features a rotary switch to selectamong ten lighting time options including pre-dawn settings and LVD override protection. Detectsday and night using the PV array. Five-year limited warranty.

SunLight


CONT

ROLL

ERS

Controllers

28 3/03

Xantrex C12

C12 – PWM 3 stage solar charge, DC load and auto lighting controllerThe C12 has an LED status light displaying both charging functions and battery charge state at aglance. The load control function (LVD) will disconnect DC loads if batteries reach low-voltagecondition and reconnect once batteries are recharged. A simple one-time reconnect switch turnspower back on for ten minutes once in LVD. An optional temperature sensor ensures precisebattery charging regardless of battery temperature fluctuations. • Field adjustable setpoints withremovable knobs • Automatic reset of overload protection • Automatic control of lighting systemswith adjustable run duration from 2 to 8 hours or dusk to dawn. • ETL listed to UL1741 No. 2.Two-year warranty.

Rated RatedModel Voltage PV Current Load Current Dimensions Weight (lbs) MSRP

C12 12V 12 A 12 A 6.5” x 4.3” x 1.5” 1.5 $110.00

Xantrex

Model Voltage Rated PV Current Rated Load Current Dimensions Weight MSRP

C35 12/24V 35 A or 35 A 8.0”x5” x 2.5” 2.5 lbs $119.00C40 12/24/48V 40 A or 40 A 10” x 5” x 2.5” 3.0 lbs $159.00C60 12/24V 60 A or 60 A 10” x 5” x 2.5” 3.0 lbs $199.00

AccessoriesCM LCD digital display mounts on the front of the controller for C35, C40 & C60 $99.00CM/R-50 Remote LCD digital display with 50’ cable for C35, C40 & C60 $126.00CM/R-100 Remote LCD digital display with 100’ cable for C35, C40 & C60 $146.00BTS/15 Battery temperature sensor with 15’ cable for all C series and C12 controllers $29.00BTS/35 Battery temperature sensor with 35’ cable for all C series and C12 controllers $32.00

C-Series-Charge, Diversion or Load ControllersThese pulse width modulated (PWM), field adjustable controllers work as a solar charge controller or a DC load controller or a diversion controller. All models automatically initiate a three-stage battery charging cycle andfeature an LED status light displaying charging functions and battery state-of-charge. UL listed. Two-year warranty.

Xantrex C40 CM LCD digital display

Outback MX60

MX60 Charge ControllerThe MX60 Maximum Power Point Tracking (MPPT) charge controller enables your PV system toachieve its highest possible performance. It can be used with battery systems from 12 to 60VDCwith PV open circuit voltage as high as 125VDC. Setpoints are fully adjustable. The MX60 allowsyou to use a higher output voltage PV array with a lower voltage battery. The MX60 comesstandard with a display of the PV system’s performance. The four-line, 80 character, backlit LCDdisplay is used for programming and monitoring of the system’s operation. It can be connectedto the Mate system controller and display to allow monitoring of up to eight MX60 controllers.Opto-isolated RS232 port included. Two-year warranty.

Battery Rated MaximumModel Voltage PV Current PV Voc Dimensions Weight MSRP

MX-60 12-60 VDC 60 A 125 VDC 14.5” x 5.75” x 5.75” 12 lbs $649.00

OutBack Power


CONTROLLERS

3/03 29

The Automatic Sequencing Charger™ (ASC) is a very compact,efficient 100% solid-state battery charger regulator for use in PVsystems. The ASC is a negative-ground switching shunt regulator,housed in an anodized aluminum chassis and encapsulated in a hard epoxy resin. The terminal block accepts up to 10-gauge wire or a space connector, providing simple installation. The ASC is FMapproved for hazardous locations, UL listed, and provides lightning and reverse leakage protection. The ASC PLUS features a low-voltage load disconnect, a waterproof battery fuse, and a linear LED display indicating battery status.

The MARK/15™ is a solid-state charge controller for use in PV systems with currents up to 15amps. It includes a full-featured LCD meter to display battery voltage, array current and charge set-point. It is intended to flush-mount within a wall for a very distinctive appearance. Generalspecifications include fuse protection on both battery and array and bargraph battery conditionindicator. The Mark/15 is UL Recognized.

The MARK/22 is similar to the MARK/15 but is rated for 22 amps of PV current. It also has alow-power consumption LCD digital display, which can show two different system parameters -battery voltage and array current.

Specialty Concepts, Inc.

Mark 15

Rated PV Rated Load WeightModel Description Voltage Current Current Dimensions (lbs) MSRP

ASC-12/4 12 V 4 A n/a 6” x 3.5” x 3” 0.63 $46.00ASC-12/8 12 V 8 A n/a 6” x 3.5” x 3” 0.63 $49.00ASC-12/8 A Temp Compensation 12 V 8 A n/a 6” x 3.5” x 3” 0.63 $58.00ASC-12/8 AE Temp Comp, Low-volt Disc 12 V 8 A 10 A 6” x 3.5” x 3” 0.63 $70.00ASC-12/8 E Low-volt Disconnect 12 V 8 A 10 A 6” x 3.5” x 3” 0.63 $61.00ASC-12/12 12 V 12 A n/a 6” x 3.5” x 3” 0.63 $56.00ASC-12/12 A Temp Compensation 12 V 12 A n/a 6” x 3.5” x 3” 0.63 $66.00ASC-12/12 AE Temp Comp, Low-volt Disc 12 V 12 A 10 A 6” x 3.5” x 3” 0.63 $83.00ASC-12/12 E Low-volt Disconnect 12 V 12 A 10 A 6” x 3.5” x 3” 0.63 $72.00ASC-12/16 12 V 16A n/a 6.5” x 5” x 3” 1.00 $65.00ASC-12/16 A Temp Compensation 12 V 16A n/a 6.5” x 5” x 3” 1.00 $76.00ASC-12/16 AE Temp Comp, Low-volt Disc 12V 16A 10 A 6.5” x 5” x 3” 1.00 $92.00ASC-12/16 E Low-volt Disconnect 12 V 16A 10 A 6.5” x 5” x 3” 1.00 $81.00ASC-24/8 24 V 8 A n/a 6” x 3.5” x 3” 0.63 $49.00ASC-24/8 A Temp Compensation 24 V 8 A n/a 6” x 3.5” x 3” 0.63 $60.00ASC-24/8 AE Temp Comp, Low-volt Disc 24 V 8 A 10 A 6” x 3.5” x 3” 0.63 $76.00ASC-24/8 E Low-volt Disconnect 24 V 8 A 10 A 6” x 3.5” x 3” 0.63 $65.00ASC-24/16 24 V 16 A n/a 6.5” x 5” x 3” 1.00 $65.00ASC-24/16 A Temp Compensation 24 V 16 A n/a 6.5” x 5” x 3” 1.00 $76.00ASC-24/16 AE Temp Comp, Low-volt Disc 24 V 16 A 10 A 6.5” x 5” x 3” 1.00 $92.00ASC-24/16 E Low-volt Disconnect 24 V 16 A 10 A 6.5” x 5” x 3” 1.00 $81.00ASCP-12/15 Plus 12 V 15 A 10 A 6.5” x 5” x 3” 1.00 $90.00MARK/15-12 12 V 15 A n/a 9.5” x 6” x 4” 1.25 $99.00MARK/22-12 12 V 22 A n/a 9.5” x 6” x 4” 1.50 $114.00

ASC Charger

SunWize Economy Lighting System ControllerThis special purpose solar charge controller enables PWM battery charging and nighttimelighting control using a solar module as the dusk sensor. The unit includes a field-adjustabledusk timer for 2, 4, 6, 8, 10 hours or dusk to dawn. Includes load-ON setting for day test, statusLED’s and low battery load disconnect. Five-year warranty.

Model Voltage Max. Load & PV Current Dimensions MSRPPV12T 12 VDC 12 A 5.7” x 2.6” x 2.1” $90.00PV 12T Lighting Controller

Controllers A d v a n c e d E n e r g y G r o u p

CONT

ROLL

ERS

30 3/03

Model Voltage Rated Rated Dimensions Unit WeightPV Current Load Current (lbs) MSRP

Solar Boost 2000E 12 V 25 A 25 A 4.6” x 6.4” x 1.8” 2 $229.00

Solar Boost 6024HDL 48 V 60 A 60 A 10” x 8.75” x3.5” 9.5 lbs $589.00with display

Solar Boost 6024HL 48 V 60 A 60 A 10” x 8.75” x 3.5” 9.25lbs $509.00w/o display

Solar Boost 3048DL 24/48 V 30 A 30 A 10” x 8.75” x 3.5” 9 $559.00with display

Solar Boost 3048L 24/48 V 30 A 30 A 10” x 8.75” x 3.5” 8.75 $479.00



Accessories:

SB2000E Wall Mount Box –1/2” conduit knockouts 2 $28.00SB3048PDL front panel digital display – Add to SB3048L to make SB3048DL 1 $115.00SB50PDL front panel digital display – Add to SB50L to make SB50DL 1 $115.00SB50RD25 Remote display w/25’ cable for SB3048L, SB50L, SB6024HL 4.5” x 4/5” x 1.75” 2 $109.00Battery Temperature Sensor w/20’ cable for all RVPP controllers 1 $28.00SB6024HPDL front panel digital display – Add to SB6024HL to make SB6024HDL 2 $115.00

Controllers

Solar Boost 2000E

Solar Boost™ ControllersRV Power Products controllers employ Maximum Power Point Tracking (MPPT) which increasescharge current up to 30%. These controllers offer Pulse Width Modulation (PWM) charge voltagecontrol using reliable power MOSFET transistors. A fully automatic electronic current limit preventsoverload. A manual equalize function is also provided to periodically condition liquid electrolyte lead-acid batteries. A digital display shows battery voltage, solar panel current, output charge current,charge mode and state-of-charge. The controllers feature an advanced fully automatic three-stagecharge control system to ensure the battery is properly and fully charged. An optional digital displayfor both can be provided in the controller or as a remote panel installed up to 300’ away (or both). The 2000E includes a multifunction digital display. The 6024H is specially designed to receive a highvoltage 36V or 48V PV array input and charge a 12V or 24V battery at up to 60A. Solar Boost 3048,50 and 6024H are ETL listed. 36-month limited warranty.

RV Power Products

Features:• Patented MPPT technology• Multi-stage PWM charge control

• Durable powder coat finish• Conformal coated electronics

• 3 year extended warranty• Optional temperature compensation

Meters

TM-2020 Battery MeterThe TriMetric battery monitors are designed to assist in battery care, conservation and systemmaintenance of battery powered systems that use storage batteries with system voltage from 12-48 volts. The TM-2020 measures volts, amps and amp-hours and features a “battery % full”display and a “battery reminders” display.

TriMetric

TriMetric TM-2020

Model Voltage Dimensions MSRPTM-2020 12-24V 4.75” x 4.50” x 1.75” $199.0048V Adapter – Used to adapt TM-2020 for 48 volt use $30.00Wiremold Box for flush mounting #2348-2 $12.00



CONT

ROLL

ERS

Controllers

3/03

Xantrex C12

C12 – PWM 3 stage solar charge, DC load and auto lighting controllerThe C12 has an LED status light displaying both charging functions and battery charge state at aglance. The load control function (LVD) will disconnect DC loads if batteries reach low-voltagecondition and reconnect once batteries are recharged. A simple one-time reconnect switch turnspower back on for ten minutes once in LVD. An optional temperature sensor ensures precisebattery charging regardless of battery temperature fluctuations. • Field adjustable setpoints withremovable knobs • Automatic reset of overload protection • Automatic control of lighting systemswith adjustable run duration from 2 to 8 hours or dusk to dawn. • ETL listed to UL1741 No. 2.Two-year warranty.

Rated RatedModel Voltage PV Current Load Current Dimensions Weight (lbs) MSRP

C12 12V 12 A 12 A 6.5” x 4.3” x 1.5” 1.5 $110.00

Xantrex

Model Voltage Rated PV Current Rated Load Current Dimensions Weight MSRP

C35 12/24V 35 A or 35 A 8.0”x5” x 2.5” 2.5 lbs $119.00C40 12/24/48V 40 A or 40 A 10” x 5” x 2.5” 3.0 lbs $159.00C60 12/24V 60 A or 60 A 10” x 5” x 2.5” 3.0 lbs $199.00

AccessoriesCM LCD digital display mounts on the front of the controller for C35, C40 & C60 $99.00CM/R-50 Remote LCD digital display with 50’ cable for C35, C40 & C60 $126.00CM/R-100 Remote LCD digital display with 100’ cable for C35, C40 & C60 $146.00BTS/15 Battery temperature sensor with 15’ cable for all C series and C12 controllers $29.00BTS/35 Battery temperature sensor with 35’ cable for all C series and C12 controllers $32.00

C-Series-Charge, Diversion or Load ControllersThese pulse width modulated (PWM), field adjustable controllers work as a solar charge controller or a DC load controller or a diversion controller. All models automatically initiate a three-stage battery charging cycle andfeature an LED status light displaying charging functions and battery state-of-charge. UL listed. Two-year warranty.

Xantrex C40 CM LCD digital display

Outback MX60

MX60 Charge ControllerThe MX60 Maximum Power Point Tracking (MPPT) charge controller enables your PV system toachieve its highest possible performance. It can be used with battery systems from 12 to 60VDCwith PV open circuit voltage as high as 125VDC. Setpoints are fully adjustable. The MX60 allowsyou to use a higher output voltage PV array with a lower voltage battery. The MX60 comesstandard with a display of the PV system’s performance. The four-line, 80 character, backlit LCDdisplay is used for programming and monitoring of the system’s operation. It can be connectedto the Mate system controller and display to allow monitoring of up to eight MX60 controllers.Opto-isolated RS232 port included. Two-year warranty.

Battery Rated MaximumModel Voltage PV Current PV Voc Dimensions Weight MSRP

MX-60 12-60 VDC 60 A 125 VDC 14.5” x 5.75” x 5.75” 12 lbs $649.00

OutBack Power


CONTROLLERS

3/03

The Automatic Sequencing Charger™ (ASC) is a very compact,efficient 100% solid-state battery charger regulator for use in PVsystems. The ASC is a negative-ground switching shunt regulator,housed in an anodized aluminum chassis and encapsulated in a hard epoxy resin. The terminal block accepts up to 10-gauge wire or a space connector, providing simple installation. The ASC is FMapproved for hazardous locations, UL listed, and provides lightning and reverse leakage protection. The ASC PLUS features a low-voltage load disconnect, a waterproof battery fuse, and a linear LED display indicating battery status.

The MARK/15™ is a solid-state charge controller for use in PV systems with currents up to 15amps. It includes a full-featured LCD meter to display battery voltage, array current and charge set-point. It is intended to flush-mount within a wall for a very distinctive appearance. Generalspecifications include fuse protection on both battery and array and bargraph battery conditionindicator. The Mark/15 is UL Recognized.

The MARK/22 is similar to the MARK/15 but is rated for 22 amps of PV current. It also has alow-power consumption LCD digital display, which can show two different system parameters -battery voltage and array current.

Specialty Concepts, Inc.

Mark 15

Rated PV Rated Load WeightModel Description Voltage Current Current Dimensions (lbs) MSRP

ASC-12/4 12 V 4 A n/a 6” x 3.5” x 3” 0.63 $46.00ASC-12/8 12 V 8 A n/a 6” x 3.5” x 3” 0.63 $49.00ASC-12/8 A Temp Compensation 12 V 8 A n/a 6” x 3.5” x 3” 0.63 $58.00ASC-12/8 AE Temp Comp, Low-volt Disc 12 V 8 A 10 A 6” x 3.5” x 3” 0.63 $70.00ASC-12/8 E Low-volt Disconnect 12 V 8 A 10 A 6” x 3.5” x 3” 0.63 $61.00ASC-12/12 12 V 12 A n/a 6” x 3.5” x 3” 0.63 $56.00ASC-12/12 A Temp Compensation 12 V 12 A n/a 6” x 3.5” x 3” 0.63 $66.00ASC-12/12 AE Temp Comp, Low-volt Disc 12 V 12 A 10 A 6” x 3.5” x 3” 0.63 $83.00ASC-12/12 E Low-volt Disconnect 12 V 12 A 10 A 6” x 3.5” x 3” 0.63 $72.00ASC-12/16 12 V 16A n/a 6.5” x 5” x 3” 1.00 $65.00ASC-12/16 A Temp Compensation 12 V 16A n/a 6.5” x 5” x 3” 1.00 $76.00ASC-12/16 AE Temp Comp, Low-volt Disc 12V 16A 10 A 6.5” x 5” x 3” 1.00 $92.00ASC-12/16 E Low-volt Disconnect 12 V 16A 10 A 6.5” x 5” x 3” 1.00 $81.00ASC-24/8 24 V 8 A n/a 6” x 3.5” x 3” 0.63 $49.00ASC-24/8 A Temp Compensation 24 V 8 A n/a 6” x 3.5” x 3” 0.63 $60.00ASC-24/8 AE Temp Comp, Low-volt Disc 24 V 8 A 10 A 6” x 3.5” x 3” 0.63 $76.00ASC-24/8 E Low-volt Disconnect 24 V 8 A 10 A 6” x 3.5” x 3” 0.63 $65.00ASC-24/16 24 V 16 A n/a 6.5” x 5” x 3” 1.00 $65.00ASC-24/16 A Temp Compensation 24 V 16 A n/a 6.5” x 5” x 3” 1.00 $76.00ASC-24/16 AE Temp Comp, Low-volt Disc 24 V 16 A 10 A 6.5” x 5” x 3” 1.00 $92.00ASC-24/16 E Low-volt Disconnect 24 V 16 A 10 A 6.5” x 5” x 3” 1.00 $81.00ASCP-12/15 Plus 12 V 15 A 10 A 6.5” x 5” x 3” 1.00 $90.00MARK/15-12 12 V 15 A n/a 9.5” x 6” x 4” 1.25 $99.00MARK/22-12 12 V 22 A n/a 9.5” x 6” x 4” 1.50 $114.00

ASC Charger

SunWize Economy Lighting System ControllerThis special purpose solar charge controller enables PWM battery charging and nighttimelighting control using a solar module as the dusk sensor. The unit includes a field-adjustabledusk timer for 2, 4, 6, 8, 10 hours or dusk to dawn. Includes load-ON setting for day test, statusLED’s and low battery load disconnect. Five-year warranty.

Model Voltage Max. Load & PV Current Dimensions MSRPPV12T 12 VDC 12 A 5.7” x 2.6” x 2.1” $90.00PV 12T Lighting Controller

Controllers

CONTROLLERS

3/03

Meters

Link 10 (formerly E-Meter)Easy to use multicolor displays show volts, amps, amp hours consumed and operating timeremaining. The Link 10 allows you to select Automatic, Sleep and Scanning modes and calculateand display charging efficiency. By adding an optional prescaler, Link 10 can monitor singlebattery banks up to 500 volts. Compatible with 12 or 24 volt DC systems. Includes DC shunt. 18month warranty.

Dimensions: Face diameter: 2.5”, Barrel diameter: 1.95”, Depth: 3.15”

Xantrex

Xantrex Link 10 Model Weight MSRP

Link 10 Standard - w/500-amp shunt 8 oz $250.00Link 10 Choice - w/500-amp shunt, RS232 computer port, and alarm switch 8 oz $375.00Link 10 Deluxe - w/1000-amp shunt and RS232 computer port 8 oz $460.00Color-coded twisted pair cable - 25 ft. $44.00Prescaler - 0-100 volts to extend voltage range covered by meter $75.00

Xantrex TM500AThe TM500A provides easy to understand information such as produced and used DC current. It keeps track of the energy your system has available and energy consumed to ensure adequatereserve power capacity and longevity of your battery bank. It provides data on all critical systemfunctions and is capable of monitoring total accumulated charge power from sources such as PVarrays, wind power systems and generator sets. The TM500A comes with 50 feet of communicationcable and a 500 amp shunt. Compatible with 12 or 24 volt DC systems. Two-year warranty.

Xantrex TM500A

Model Dimensions Weight MSRP

TM500A - with shunt, 50’ cable, shunt board 3.88” x 5.377” x 1.25” 2.5 lbs $245.00TM500A-NS - no shunt, 50’ cable, shunt board 3.88” x 5.377” x 1.25” 2.5 lbs $195.00TM48 - high voltage shunt board for 48VDC systems $40.00

AC Watt hour MeterThis standard utility grade meter, certified and calibrated, is useful in PV-grid tied or stand- alonesystems for monitoring the solar energy production from sine wave DC-AC inverters. Rated forindoor/outdoor use for 120/240V-60Hz single-phase operation. Numeric display in kilowatt-hoursenables simple reading of energy produced. Meter socket, sold separately, includes meter ring,painted cast aluminum body with 1” threaded conduct hubs & GND lug. Meter seal is used todetermine unauthorized entry.

SunWize®

Model Size Weight MSRPkWhr Meter 6” dia. 4.5 $39.00Meter Socket 6” dia. 1.5 $29.00 Meter Seal NA NA $1.00

Xantrex Link 1000 (For use with Xantrex Freedom Series Inverters)The Link 1000 is an instrumentation and control panel designed for use with Freedom seriesinverter/chargers operated with a single battery bank. The Link 1000 is a monitoring system thatreads like a fuel gauge for the batteries displaying battery state-of-charge at a glance. You canindependently control inverter and charger functions. Compatible with 12 or 24 volt DC systems.Includes DC shunt. Thirty-month warranty.

Xantrex Link 1000 Model Dimensions Weight MSRP

Link 1000 with 500-amp shunt 3” x 4.75” x 1.1” 1.0 lbs $330.00

SHUNTS FOR ALL METERS MSRP500 amp shunt $30.00100 amp shunt $28.00

SunWize AC Watt hour Meter



CONT

ROLL

ERS

3/03

Model Voltage Rated Rated Dimensions Unit WeightPV Current Load Current (lbs) MSRP

Solar Boost 2000E 12 V 25 A 25 A 4.6” x 6.4” x 1.8” 2 $229.00

Solar Boost 6024HDL 48 V 60 A 60 A 10” x 8.75” x3.5” 9.5 lbs $589.00with display

Solar Boost 6024HL 48 V 60 A 60 A 10” x 8.75” x 3.5” 9.25lbs $509.00w/o display





Accessories:

SB2000E Wall Mount Box –1/2” conduit knockouts 2 $28.00SB3048PDL front panel digital display – Add to SB3048L to make SB3048DL 1 $115.00SB50PDL front panel digital display – Add to SB50L to make SB50DL 1 $115.00SB50RD25 Remote display w/25’ cable for SB3048L, SB50L, SB6024HL 4.5” x 4/5” x 1.75” 2 $109.00Battery Temperature Sensor w/20’ cable for all RVPP controllers 1 $28.00SB6024HPDL front panel digital display – Add to SB6024HL to make SB6024HDL 2 $115.00

Controllers

Solar Boost 2000E

Solar Boost™ ControllersRV Power Products controllers employ Maximum Power Point Tracking (MPPT) which increasescharge current up to 30%. These controllers offer Pulse Width Modulation (PWM) charge voltagecontrol using reliable power MOSFET transistors. A fully automatic electronic current limit preventsoverload. A manual equalize function is also provided to periodically condition liquid electrolyte lead-acid batteries. A digital display shows battery voltage, solar panel current, output charge current,charge mode and state-of-charge. The controllers feature an advanced fully automatic three-stagecharge control system to ensure the battery is properly and fully charged. An optional digital displayfor both can be provided in the controller or as a remote panel installed up to 300’ away (or both). The 2000E includes a multifunction digital display. The 6024H is specially designed to receive a highvoltage 36V or 48V PV array input and charge a 12V or 24V battery at up to 60A. Solar Boost 3048,50 and 6024H are ETL listed. 36-month limited warranty.

RV Power Products

Features:• Patented MPPT technology• Multi-stage PWM charge control

• Durable powder coat finish• Conformal coated electronics

• 3 year extended warranty• Optional temperature compensation

Meters

TM-2020 Battery MeterThe TriMetric battery monitors are designed to assist in battery care, conservation and systemmaintenance of battery powered systems that use storage batteries with system voltage from 12-48 volts. The TM-2020 measures volts, amps and amp-hours and features a “battery % full”display and a “battery reminders” display.

TriMetric

TriMetric TM-2020

Model Voltage Dimensions MSRPTM-2020 12-24V 4.75” x 4.50” x 1.75” $199.0048V Adapter – Used to adapt TM-2020 for 48 volt use $30.00Wiremold Box for flush mounting #2348-2 $12.00

Wind Turbines

WIN

DPOW

ER &

WAT

ER P

UMPS

52 3/03

Air-X Land LX-1 Wind Turbine

If the wind speed in your area averages 9 mph or greater, wind can be the most cost-effectiveway to generate electricity. Wind turbines can produce power day and night even in inclementweather. With equal amounts invested, wind turbines can generate up to four times moreelectricity than solar. A hybrid system with a wind turbine combined with solar panels is the mostefficient and reliable method to generate your own electricity.

Air-XThe Air-X features a new microprocessor-based peak power tracking controller resulting inincreased performance, improved battery charging capability and the elimination of “flutter”noise. The carbon-reinforced, fiber composite blades, with a modified pitch angle, furtherincrease power production. The circuit monitors the wind speed and slows the blades as itreaches its rated output preventing it from going into flutter. The Air-X Marine is powder coatedfor corrosion protection. Three-year warranty.

Southwest Windpower

Rotor Start Up Rated Power WeightAIR WIND TURBINES Voltage Diameter Wind Speed @ 28 mph (lbs) MSRP

Air X Land LX-1 12 V 46” 7 mph 400 W 13 $649.00Air X Land LX-2 24 V 46” 7 mph 400 W 13 $649.00Air X Marine MX-1 12 V 46” 7 mph 400 W 13 $875.00Air X Marine MX-2 24 V 46” 7 mph 400 W 13 $875.00

Air Industrial 12, 24 or 48 volt 46” 7 mph 400 W 14 $876.00no regulator (specify voltage)

Air Industrial Package with 12, 24 or 48 volt 46” 7 mph 400 W 15 $1,095.00regulator and dump load (specify voltage)

AIR & WINDSEEKER TOWER KITSAir Marine Tower Hardware Kit for aluminum powder coated masts $169.009’ Air Marine Aluminum Pole Set includes pole and stays only $179.00Roof Mount Kit with Seal does not include pole or lag screws (Air only) $99.00Roof Mount Kit without Seal does not include pole or lag screws (Air only) $79.00Roof Seal for roof mount kit (Air only) $31.0027’ Air Guyed Tower Kit does not include poles & anchors $99.0045’ Air Guyed Tower Kit does not include poles & anchors $170.00

ACCESSORIESCircuit Breaker 30 amp $24.00Circuit Breaker 50 amp $24.00Circuit Breaker 100 amp $46.00Stop Switch 50 amp $17.00Amp meter 30 amp $25.00External regulator and dump load for Air Industrial $209.00

SunWize® Wind Junction Box Assembly-AIRX-12/24This fully assembled wind turbine junction box is designed for use with single AIRX-12V or 24voltgenerator installations. The aluminum-3R enclosure, intended for U-bolt mounting at tower base,can be wall mounted on buildings or enclosures. The junction box provides a large wire terminalblock for up to #4 AWG and features a 25A current meter, a 50A run/stall switch, a 50A batterycircuit breaker and SOV type lightning surge arrestor with grounding lug. Two-year warranty.

Model Voltage Max Current Box Size Weight MSRP

WJB-AIRX 12/24 50A 11” X 9” X 5” 5.0 $339.00

SunWize® Wind Combiner Box Assembly-Two AIRX-12/24For installations with more than one wind turbine, this assembly has all the features of theJunction Box Assembly. It combines the output of two-AIRX wind turbines and allows forindependent monitoring, control and disconnection. Circuit breaker rated 100A, DC ammeter is0-50A. Two-year warranty.


WCB-2AIRX 12/24 100A 14” X 10” X 7” 10.0 $499.00

SunWize AIR-X Junction Box Assembly


WINDPOW

ER &W

ATER PUMPS

3/03

Wind Turbines

Rotor Start Up WeightWHISPER WIND TURBINES Voltage Diameter Wind Speed Rated Power (lbs) MSRP

H-40 with EZ Wire II 24 or 48 volt 7 feet 7.5 mph 900 W @28mph 47 $1,595.00

H-40 with EZ Wire I 12 volt 7 feet 7.5 mph 900 W @28mph 47 $1,895.00

H-80 with EZ Wire II 24 or 48 volt 10 feet 7.0 mph 1000 W @26mph 65 $1,995.00

H-80 with EZ Wire I 12 volt 10 feet 7.0 mph 1000 W @26mph 65 $2,365.00

H-80 Waterpumper 140 V, 3 phase 10 feet 6.5 mph 1000 W @26mph 86 $1,995.00

H-80 High Voltage 220 VDC 10 feet 7.0 mph 1000 W @26mph 65 $3,595.00

175 with EZ Wire I 24 or 48 volt 15 feet 7.1 mph 3200 W @24mph 155 $5,455.00

175 High Voltage 220 volt 15 feet 7.1 mph 3200 W @24mph 155 $7,325.00

H-40 Marine with EZ Wire II 24 or 48 volt 7 feet 7.5 mph 900 W @28mph 47 $1795.00

H-40 Marine with EZ Wire I 12 volt 7 feet 7.5 mph 900 W @28mph 47 $2095.00

H-80 Marine with EZ Wire II 24 or 48 volt 10 feet 7.0 mph 1000 W @ 26mph 65 $2195.00

H-80 Marine with EZ Wire I 12 volt 10 feet 7.0 mph 1000 W @26mph 65 $2565.00

WHISPER TOWER KITS Description MSRP24’ Whisper Guyed Tower Kit does not include poles & anchors (H40 & H80) $260.00

30’ Whisper Guyed Tower Kit does not include poles & anchors (H40 & H80) $435.00




30’ Whisper Guyed Tower Kit does not include poles & anchors (Whisper 175) $920.00

42’ Whisper Guyed Tower Kit does not include poles & anchors (Whisper 175) $990.00

70’ Whisper Guyed Tower Kit does not include poles & anchors (Whisper 175) $1,365.00

30’ EZ Tower - free standing includes pipe and base & delivery (H40 & H80) $1,699.00

Accessories For All Models: Description MSRP

36” Augers set of four earth anchors $55.00

36” Galvanized Augers set of four earth anchors $175.00

48” Augers set of four earth anchors $60.00

48” Galvanized Augers set of four earth anchors $200.00

60” Galvanized Augers set of four earth anchors (for 65’, 70’, 80’, 84’) $270.00

Southwest Windpower

EZ Wire II Controller

Whisper Wind TurbinesWhisper Turbines feature a cast aluminum frame and smooth, quiet operation. The H-40 and theH-80 models incorporate a permanent magnet brushless alternator and a high-efficiency,composite airfoil blade design. The H-80 has twice the swept blade area as the H40, providingdouble the potential energy. The 175 model will deliver in excess of 500 kWh per month in a 12mph wind and features a low wind startup. This turbine has a 15-foot rotor diameter providing175 sq. ft. of swept area. Two-year warranty.

The marine versions are designed for coastal and offshore applications featuring a powder coatingfor corrosion protection, stainless steel hardware, marine grade wire and watertight housings.

All models are equipped with the EZ Wire System Center that controls battery charging. Itscompact, safe cabinet design features easily settable voltage regulation points, load dump andload dump isolation from the battery. The EZ Wire I is designed to control wind/PV combosystems and the EZ Wire II controls the wind turbine only.

Whisper H80 Wind Turbine



Wind Turbines

WIN

DPOW

ER &

WAT

ER P

UMPS

3/03

Air-X Land LX-1 Wind Turbine

If the wind speed in your area averages 9 mph or greater, wind can be the most cost-effectiveway to generate electricity. Wind turbines can produce power day and night even in inclementweather. With equal amounts invested, wind turbines can generate up to four times moreelectricity than solar. A hybrid system with a wind turbine combined with solar panels is the mostefficient and reliable method to generate your own electricity.

Air-XThe Air-X features a new microprocessor-based peak power tracking controller resulting inincreased performance, improved battery charging capability and the elimination of “flutter”noise. The carbon-reinforced, fiber composite blades, with a modified pitch angle, furtherincrease power production. The circuit monitors the wind speed and slows the blades as itreaches its rated output preventing it from going into flutter. The Air-X Marine is powder coatedfor corrosion protection. Three-year warranty.

Southwest Windpower

Rotor Start Up Rated Power WeightAIR WIND TURBINES Voltage Diameter Wind Speed @ 28 mph (lbs) MSRP

Air X Land LX-1 12 V 46” 7 mph 400 W 13 $649.00Air X Land LX-2 24 V 46” 7 mph 400 W 13 $649.00Air X Marine MX-1 12 V 46” 7 mph 400 W 13 $875.00Air X Marine MX-2 24 V 46” 7 mph 400 W 13 $875.00

Air Industrial 12, 24 or 48 volt 46” 7 mph 400 W 14 $876.00no regulator (specify voltage)

Air Industrial Package with 12, 24 or 48 volt 46” 7 mph 400 W 15 $1,095.00regulator and dump load (specify voltage)

AIR & WINDSEEKER TOWER KITSAir Marine Tower Hardware Kit for aluminum powder coated masts $169.009’ Air Marine Aluminum Pole Set includes pole and stays only $179.00Roof Mount Kit with Seal does not include pole or lag screws (Air only) $99.00Roof Mount Kit without Seal does not include pole or lag screws (Air only) $79.00Roof Seal for roof mount kit (Air only) $31.0027’ Air Guyed Tower Kit does not include poles & anchors $99.0045’ Air Guyed Tower Kit does not include poles & anchors $170.00

ACCESSORIESCircuit Breaker 30 amp $24.00Circuit Breaker 50 amp $24.00Circuit Breaker 100 amp $46.00Stop Switch 50 amp $17.00Amp meter 30 amp $25.00External regulator and dump load for Air Industrial $209.00

SunWize® Wind Junction Box Assembly-AIRX-12/24This fully assembled wind turbine junction box is designed for use with single AIRX-12V or 24voltgenerator installations. The aluminum-3R enclosure, intended for U-bolt mounting at tower base,can be wall mounted on buildings or enclosures. The junction box provides a large wire terminalblock for up to #4 AWG and features a 25A current meter, a 50A run/stall switch, a 50A batterycircuit breaker and SOV type lightning surge arrestor with grounding lug. Two-year warranty.


WJB-AIRX 12/24 50A 11” X 9” X 5” 5.0 $339.00

SunWize® Wind Combiner Box Assembly-Two AIRX-12/24For installations with more than one wind turbine, this assembly has all the features of theJunction Box Assembly. It combines the output of two-AIRX wind turbines and allows forindependent monitoring, control and disconnection. Circuit breaker rated 100A, DC ammeter is0-50A. Two-year warranty.


WCB-2AIRX 12/24 100A 14” X 10” X 7” 10.0 $499.00

SunWize AIR-X Junction Box Assembly


Water Pumps

WIN

DPOW

ER &

WAT

ER P

UMPS

3/03

USPC 2000 Controller

Universal Solar Pump ControllerWater pumping is the most common use for the AeroVironment Universal Solar Pump Controller.It can operate nearly any standard AC motor up to 5 HP directly from a solar array. Less costly,locally made and serviceable pumps may be used. The USPC enables the water pumpingsystem to use a generator or the utility grid for a backup. A solar water pumping system usingthe USPC controller should be considered if you need more water or more lift than a Grundfossolar electric pumping system can handle. Two-year standard warranty.

AeroVironment

Solar powered water pumping systems are currently being used to irrigate crops, water thirsty livestock and provide potablewater, and should be considered for replacing generators and power line extensions. Unlike generator powered systems, solarwater pumping systems do not require trips for refueling or constant maintenance. Since solar water pumping systems producethe most water when it is sunny and hot, they are a natural power solution. The pump you use will depend on your applicationand the water source. A surface pump is a more economical solution if you are pumping from a water source close to thesurface. These pumps can push water a great distance or pressurize it for domestic water use. Submersible pumps can deliverwater from as far as 1200 feet. A common application is to use a submersible pump operating only during daylight hours whichpumps water into a storage tank. A separate system with a booster pump operating from a battery bank can pressurize thewater and deliver the water day or night.

There are several important factors you need to specify to choose the optimum solar pumping system design. The worksheet belowwill help you compile the information you need. Contact your dealer once you have this worksheet filled out for a price quote.

SIZING YOUR SOLAR PUMPING SYSTEM WORKSHEET

Type of Water Source (Check one): Stream, Lake or Pond Cistern or Dug Well Drilled/Deep Well

Other __________________ Season of operation (months)

Depth to Water: Ft. (Be sure to account for variations) Distance of Float Switch Cable __________________

Estimated Well Capacity: GPM Amount of Water Required: GPD (Winter) GPD (Spring)

Well Inside Diameter (If applicable) in. GPD (Summer) GPD (Fall)

Type of Application (Check one): Domestic Water Livestock Irrigation Other __________________

Vertical Lift Required From Water Surface to Outlet: ft. Type of Storage: Above Ground Other __________________

Geographical Location of System Temperature: ______ °F Min. ______ °F Max

Elevation Above Sea Level: ______ Ft.Distance from Solar Array to Pump: ______ ft.

Options: (please check if you would like one of the following): Float Switch Generator Backup

General Solar Pumping InformationFlow RatesGPD - Gallons per Day (To estimate GPD,

multiply GPH by peak sun hours for location)GPH - Gallons per Hour (To estimate GPH,

multiply GPM by 60 min./hour nGPM - Gallons per Minute)

Pump Performance Vs. Solar Array OutputAs voltage varies, flow rate will vary proportionallyAverage stays nearly constantWatts = Volts x Amps

Conversion FactorsFeet of Lift to PSIG - Divide Feet by 2.31US Gallons to Liters - Multiply Gallons by 3.785Feet to Meters - Divide Feet by 3.28

Consumption EstimatesPeople–10-100 GPD per person for all purposesLarge Livestock (horses, cattle) - 10 GPD per animalDairy Cattle - 35 GPD per animalSmall Livestock (sheep, hogs, etc.) - 2-4 GPD per animal100 Chickens - 4 GPD

Max PV Array Power Max Peak Dimensions WeightModel (Isc) Max Current Sustained Efficiency (Inches) (lbs.) MSRP

USPC 2000 18 amps 9.5 amps 2.2 kW 97% 18” x 9” x 6” 17 $2,500.00USPC 5000 18 amps 24 amps 5.5 kW 97% 18” x 9” x 6” 17 $4,200.00

WINDPOW

ER &W

ATER PUMPS

3/03 55

Water Pumps

The Flowlight booster pumps are a good choice to pressurize your water in a remote home from astorage tank in order to enjoy “city pressure.” The Solar Force and Solar Ram pumps are goodchoices to move the water from a spring or creek to a storage tank, especially when longpipelines are involved. These pumps can be operated from either a battery system or a solardirect system. Please contact your dealer to determine the correct pump for your application.One-year warranty.

Flowlight® Booster Pump

SHURflo 2088 series surface pumps offer an inexpensive, simple torebuild, rugged booster pump that can deliver up to 3.6 GPM from a 12 or 24 VDC battery bank. A good pump for a cabin or small homesystem. They can run dry without damage and are UL listed. The 9300model submersible pump will provide many years of service and can be rebuilt in the field with simple tools. This pump has become a favoritewith ranchers, remote homeowners and missionaries for the small solararrays needed and ease of use. This pump produces around 1 GPM from up to 220 feet of lift. The PowerTwin Pump is one of the most efficient high-flow, self-priming pumps and features a Santoprene®diaphragm, Viton® valves, and a thermally protected motor with heat sink. Includes dual manifoldsystem with 5/8” hose barb ports. One-year warranty.

SHURflo

Dankoff Solar Surface Pumps

SHURflo Power Twin Pump

SHURflo 2088 Surface Pump

Model Voltage Current Flow Rate Weight (lbs) MSRP

Demand Pumps2088-443-144 Standard 12VDC 9.1A 3.6GPM 4.8 $118.002088-514-145 High Flow 12VDC 9.0A 3.6GPM 6.8 $189.002088-414-534 Premium 12VDC 9.0A 3.6GPM 6.8 $254.852088-474-144 Standard 24VDC 2.71A 3.0GPM 4.9 $139.702088-574-534 Premium 24VDC 4.5A 3.6GPM 6.4 $256.202088-594-154 Standard 115VAC 0.94A 3.3GPM 5.1 $191.00170-061-29 Strainer for 2088’s Twist on strainer, stainless steel screen, 1/2”MPT inlet, 1/2”FPT outlet $12.004111-035 Power Twin 12VDC 12.1A 6.25GPM 7.9 $299.004000-421-114 Power Twin 24VDC 9.0A 6.5GPM 8.0 $299.00Submersible Pump Vertical Lift9325-043-011 Submersible 24VDC 2.6A 1.0GPM 6.0 220ft $745.00902-100 Pump Controller 24VDC with float switch terminals 2.0 $132.00902-200 Pump Controller 12/24VDC with weatherproof enclosure,

float switch terminals and water level probes 8.0 $325.00

Voltage Current Power Flow Rate Maximum WeightModel (VDC) (amps) (watts) (GPM) Vertical Lift (lbs.) MSRP

Flowlight, Booster 2920 12 7.5 .67 4.5 450 ft. 15 $540.00Flowlight, Booster 2910-12 (Low Speed) 12 6.0 .75 3.1 230 ft. 15 $520.00Sub Flowlight 2503-24 24 – 204 2.15 240 ft. 16 $475.00Slow Pump 1304-24 24 – 196 1.48 320 ft. 16 $475.00Slow Pump 2507-24 24 – 195 3.65 140 ft. 16 $475.00Accessories for Flowlight Booster PumpInline Filter (required to protect the pump from abrasive material) $44.00Purex PX-05 Filter Cartridge $32.00Easy Installation Kit (pressure switch, gauge, control valves and tee fitting) $98.00Dry Run Switch (prevents dry run damage) $50.00

Standard Model 2920-V Low Speed Model 2910-VPressure • PSI (kg/sq. cm) 30 (2.1) 40 (2.8) 50 (3.5) 65 (4.6) 30 (2.1) 40 (2.8) 50 (3.5) 65 (4.6)

Flow Rate • GPM (lpm) 4.5 (17) 4.5 (17) 4.6 (16) 4.1 (15) 3.4 (13) 3.3 (12) 3.1 (12) 2.7 (10)Current Draw • AMPS 12V 13 15 16 22 10 11 12 15

AMPS 24V 6.5 7.5 8 11 5 5.5 6 7.5AMPS 115VAC 1.7 2.0 2.1 2.9 AC not available

SHURflo 902-200 Controller



WINDPOW

ER &W

ATER PUMPS

3/03

Water Pumps

The Flowlight booster pumps are a good choice to pressurize your water in a remote home from astorage tank in order to enjoy “city pressure.” The Solar Force and Solar Ram pumps are goodchoices to move the water from a spring or creek to a storage tank, especially when longpipelines are involved. These pumps can be operated from either a battery system or a solardirect system. Please contact your dealer to determine the correct pump for your application.One-year warranty.

Flowlight® Booster Pump

SHURflo 2088 series surface pumps offer an inexpensive, simple torebuild, rugged booster pump that can deliver up to 3.6 GPM from a 12 or 24 VDC battery bank. A good pump for a cabin or small homesystem. They can run dry without damage and are UL listed. The 9300model submersible pump will provide many years of service and can be rebuilt in the field with simple tools. This pump has become a favoritewith ranchers, remote homeowners and missionaries for the small solararrays needed and ease of use. This pump produces around 1 GPM from up to 220 feet of lift. The PowerTwin Pump is one of the most efficient high-flow, self-priming pumps and features a Santoprene®diaphragm, Viton® valves, and a thermally protected motor with heat sink. Includes dual manifoldsystem with 5/8” hose barb ports. One-year warranty.

SHURflo

Dankoff Solar Surface Pumps

SHURflo Power Twin Pump

SHURflo 2088 Surface Pump

Model Voltage Current Flow Rate Weight (lbs) MSRP

Demand Pumps2088-443-144 Standard 12VDC 9.1A 3.6GPM 4.8 $118.002088-514-145 High Flow 12VDC 9.0A 3.6GPM 6.8 $189.002088-414-534 Premium 12VDC 9.0A 3.6GPM 6.8 $254.852088-474-144 Standard 24VDC 2.71A 3.0GPM 4.9 $139.702088-574-534 Premium 24VDC 4.5A 3.6GPM 6.4 $256.202088-594-154 Standard 115VAC 0.94A 3.3GPM 5.1 $191.00170-061-29 Strainer for 2088’s Twist on strainer, stainless steel screen, 1/2”MPT inlet, 1/2”FPT outlet $12.004111-035 Power Twin 12VDC 12.1A 6.25GPM 7.9 $299.004000-421-114 Power Twin 24VDC 9.0A 6.5GPM 8.0 $299.00Submersible Pump Vertical Lift9325-043-011 Submersible 24VDC 2.6A 1.0GPM 6.0 220ft $745.00902-100 Pump Controller 24VDC with float switch terminals 2.0 $132.00902-200 Pump Controller 12/24VDC with weatherproof enclosure,

float switch terminals and water level probes 8.0 $325.00

Voltage Current Power Flow Rate Maximum WeightModel (VDC) (amps) (watts) (GPM) Vertical Lift (lbs.) MSRP

Flowlight, Booster 2920 12 7.5 .67 4.5 450 ft. 15 $540.00Flowlight, Booster 2910-12 (Low Speed) 12 6.0 .75 3.1 230 ft. 15 $520.00Sub Flowlight 2503-24 24 – 204 2.15 240 ft. 16 $475.00Slow Pump 1304-24 24 – 196 1.48 320 ft. 16 $475.00Slow Pump 2507-24 24 – 195 3.65 140 ft. 16 $475.00Accessories for Flowlight Booster PumpInline Filter (required to protect the pump from abrasive material) $44.00Purex PX-05 Filter Cartridge $32.00Easy Installation Kit (pressure switch, gauge, control valves and tee fitting) $98.00Dry Run Switch (prevents dry run damage) $50.00

Standard Model 2920-V Low Speed Model 2910-VPressure • PSI (kg/sq. cm) 30 (2.1) 40 (2.8) 50 (3.5) 65 (4.6) 30 (2.1) 40 (2.8) 50 (3.5) 65 (4.6)

Flow Rate • GPM (lpm) 4.5 (17) 4.5 (17) 4.6 (16) 4.1 (15) 3.4 (13) 3.3 (12) 3.1 (12) 2.7 (10)Current Draw • AMPS 12V 13 15 16 22 10 11 12 15

AMPS 24V 6.5 7.5 8 11 5 5.5 6 7.5AMPS 115VAC 1.7 2.0 2.1 2.9 AC not available

SHURflo 902-200 Controller

Water Pumps

WIN

DPOW

ER &

WAT

ER P

UMPS

3/03

SQ FlexThe Grundfos SQ Flex pumping systems are a giant leap forward for solar water pumping. Grundfos, the world’slargest pump manufacturer, has reduced the cost of the pumps along with reducing the power needs. The result is aGrundfos centrifugal or helical rotor quality system for about the cost of a diaphragm pump. The Grundfos SQ Flexpumping system can also be powered by a wind generator if you have the right site. The Whisper H-80Waterpumper on page 53 is the required generator.

Features: • Up to 390 foot head applications • 30-300 VDC, or 90-240 VAC single-phase AC input.• Permanent magnet high efficiency motor • Overload protection • Over temperature protection • Dry running protection• Maximum Power Point Tracking to optimize pump operation according to DC Power available.• Power line communication with the CU200 (optional) to display operational conditions

Accessories: MSRPIO 100 – Simple On/Off switch box for Grundfos SQFlex solar electric system. No float switch terminals.*Use CU200 pump controller for the Grundfos SQ Flex if a float switch is needed. $109.00

IO 101 – Generator Interface Box for Grundfos SQFlex. Includes On/Off switch (replaces IO 100) and allows for operation of SQFlex pump for either solar or manual-start generator. No float switch terminals. *Add a CU200 pump controller for the Grundfos SQFlex if a float switch is needed. $327.00

IO 102 – Wind Generator Breaker Box. This box includes a rectifier for the wind generator and a stop switch, and allows the Grundfos SQFlex pump to operate from either the H80 wind generator or a combination of wind and solar. *Add a CU200 pump controller for the Grundfos SQFlex if a float switch is needed. $319.00

CU 200 – SQFlex Control Box. This controller and system monitor can be used with solar alone or in combination with the IO101 (for manual generator backup) and/or the IO102 ( for wind generator ). The CU200 will allow you to add a float switch to shut off the pump when the storage tank is full. The system monitor display on the CU200 shows the following: • Pump operation • Full Tank • Input Power ( Watts ) • Alarm Indicator for dry running, overvoltage, overload and overtemperature. $245.00

Water Level Switch – Mechanical float switch $31.00

GF 43 Solar Module – 43 Watts, Vmp: 141, Imp: 0.31, Voc: 196.2, Isc: 0.42, Dimensions: 52” x 32”, Weight: 33 lbs. $199.00

Grundfos

SQFlex Performance RangeSQFlex Solar Application Example

Model TDH Range (Ft.) Nominal GPM Length (In.) Output Size MSRP

3 SQF-2 120 - 390 3 47 1” NPT $1,475.006 SQF-2 120 - 390 6 48 1” NPT $1,475.0011 SQF-2 40 - 300 11 49 1 1/4” NPT $1,475.0025 SQF-3 0 - 40 25 33 1 1/2” NPT $1,475.0025 SQF-6 0 - 60 25 35 1 1/2” NPT $1,475.0040 SQF-3 0 - 20 40 37 2” NPT $1,475.0075 SQF-3 0 - 40 75 39 2” NPT $1,475.00

SQ Flex Pumps


WINDPOW

ER &W

ATER PUMPS

3/03 57

Water Pumps

SA-1500The Grundfos solar direct SP line of water pumps should be considered by anyone who wants todo the job right the first time. The pumps are a stainless steel centrifugal design with nodiaphragms to replace and a water-cooled motor.

The Solar Pump 1500 series operates from a solar array of 7 or 8 modules in series up to 2000watts. This series can pump water from a maximum depth of 650 feet. Common applications forthis series of the Grundfos Solar Pump 1500 are campground water systems, livestock watering,irrigation, and larger community water systems.

The SA-1500 controller is a pump controller and an inverter. There are many pump controlfeatures in the controller such as maximum power point tracking, low water sensing, and floatswitch terminals. This controller takes the DC power from the solar array and inverts it to 65 VAC,3 phase for the pump motors.

Accessories:Contact your dealer for the accessories to complete your water pumping systems.• A solar array tracker; using a tracker on a water pumping system may increase your water

production up to 25% • Submersible pump cable • Float switches • Solar modules

Grundfos

Grundfos SA-1500

SOLAR PUMP 1500 PUMPS

08045028 SP1 A-28

03315021 SP1.5 A-21

09315015 SP2 A-15

10315010 SP3 A-10

11875005 SP8 A-5

07315003 SP14 A-3

CONTROLLER

625100 SA1500 Controller

CABLE TERMINATION KIT

115099 Cable termination kit w/sock

MSRP

$1,315.00

$1,290.00

$1,199.00

$1,112.00

$1,112.00

$1,224.00

$1,558.00

$126.00

VoltageVDC

105 to 120

105 to 120

105 to 120

105 to 120

105 to 120

105 to 120

105 to 120

Current

14A

14A

14A

14A

14A

14A

14A

Weight(lbs)

39.9

37

34.8

32.2

32.9

42.1

9.7

Total VerticalLift (in feet)

328 to 656

262 to 394

164 to 394

98 to 230

7 to 92

7 to 49

Flow RateGPM

3 to 9

7 to 12

7 to 20

17 to 37

40 to 140

80 to 180

PowerWp

2000

2000

2000

2000

2000

2000

2000

Grundfos 1500 Sizing Chart on following page

SunWize Spotlight

LOCATION:New Orleans, Louisiana

APPLICATION:Portable Electric Power (PEP)

trailer for traffic monitoring

SYSTEM:SunWize® 246W

Power Ready System using 2 – Sharp 123W solar modules


WINDPOW

ER &W

ATER PUMPS

3/03 45

Water Pumps

Grundfos continued

Grundfos Solar Pump Sizing Chart


Water Pumps

WIN

DPOW

ER &

WAT

ER P

UMPS

54 3/03

USPC 2000 Controller

Universal Solar Pump ControllerWater pumping is the most common use for the AeroVironment Universal Solar Pump Controller.It can operate nearly any standard AC motor up to 5 HP directly from a solar array. Less costly,locally made and serviceable pumps may be used. The USPC enables the water pumpingsystem to use a generator or the utility grid for a backup. A solar water pumping system usingthe USPC controller should be considered if you need more water or more lift than a Grundfossolar electric pumping system can handle. Two-year standard warranty.

AeroVironment

Solar powered water pumping systems are currently being used to irrigate crops, water thirsty livestock and provide potablewater, and should be considered for replacing generators and power line extensions. Unlike generator powered systems, solarwater pumping systems do not require trips for refueling or constant maintenance. Since solar water pumping systems producethe most water when it is sunny and hot, they are a natural power solution. The pump you use will depend on your applicationand the water source. A surface pump is a more economical solution if you are pumping from a water source close to thesurface. These pumps can push water a great distance or pressurize it for domestic water use. Submersible pumps can deliverwater from as far as 1200 feet. A common application is to use a submersible pump operating only during daylight hours whichpumps water into a storage tank. A separate system with a booster pump operating from a battery bank can pressurize thewater and deliver the water day or night.

There are several important factors you need to specify to choose the optimum solar pumping system design. The worksheet belowwill help you compile the information you need. Contact your dealer once you have this worksheet filled out for a price quote.

SIZING YOUR SOLAR PUMPING SYSTEM WORKSHEET

Type of Water Source (Check one): Stream, Lake or Pond Cistern or Dug Well Drilled/Deep Well

Other __________________ Season of operation (months)

Depth to Water: Ft. (Be sure to account for variations) Distance of Float Switch Cable __________________

Estimated Well Capacity: GPM Amount of Water Required: GPD (Winter) GPD (Spring)

Well Inside Diameter (If applicable) in. GPD (Summer) GPD (Fall)

Type of Application (Check one): Domestic Water Livestock Irrigation Other __________________

Vertical Lift Required From Water Surface to Outlet: ft. Type of Storage: Above Ground Other __________________

Geographical Location of System Temperature: ______ °F Min. ______ °F Max

Elevation Above Sea Level: ______ Ft.Distance from Solar Array to Pump: ______ ft.

Options: (please check if you would like one of the following): Float Switch Generator Backup

General Solar Pumping InformationFlow RatesGPD - Gallons per Day (To estimate GPD,

multiply GPH by peak sun hours for location)GPH - Gallons per Hour (To estimate GPH,

multiply GPM by 60 min./hour nGPM - Gallons per Minute)

Pump Performance Vs. Solar Array OutputAs voltage varies, flow rate will vary proportionallyAverage stays nearly constantWatts = Volts x Amps

Conversion FactorsFeet of Lift to PSIG - Divide Feet by 2.31US Gallons to Liters - Multiply Gallons by 3.785Feet to Meters - Divide Feet by 3.28

Consumption EstimatesPeople–10-100 GPD per person for all purposesLarge Livestock (horses, cattle) - 10 GPD per animalDairy Cattle - 35 GPD per animalSmall Livestock (sheep, hogs, etc.) - 2-4 GPD per animal100 Chickens - 4 GPD

Max PV Array Power Max Peak Dimensions WeightModel (Isc) Max Current Sustained Efficiency (Inches) (lbs.) MSRP

USPC 2000 18 amps 9.5 amps 2.2 kW 97% 18” x 9” x 6” 17 $2,500.00USPC 5000 18 amps 24 amps 5.5 kW 97% 18” x 9” x 6” 17 $4,200.00


SunDanzer™ Solar DC Refrigerators and Freezers

Energy Efficient Refrigeration

Save on system costs with SunDanzer battery-poweredsolar refrigerators and freezers. These highly efficientunits with exceptionally low energy consumption require asmaller PV system for your refrigeration needs.

SunDanzer units feature 4.33" (110 mm) of polyurethaneinsulation and coated steel cabinets. The brushless DCmotor compressor operates on 12 or 24 VDC. A patentedlow-frost system in the freezer unit reduces frost build-upfor low maintenance. SunDanzer chest-style refrigeratorsand freezers are easy to clean using the drain hole at thebottom of the unit.

With thick insulation and a refrigeration system optimizedfor solar, SunDanzer refrigerators and freezers provideoutstanding economical and reliable operation.

SunDanzer cabinets are commercially produced by Electrolux ofSweden, one of the world's leading refrigeration unit manufacturers.

Part No. Description Capacity Shipping Dimensions Shipping Weight

271DCR165 Battery Powered Refrigerator 165 liter5.8 cubic ft

104W x 79D x 99H cm41W x 31D x 39H inches

57 kg125 lbs

271DCR225 Battery Powered Refrigerator 225 liter8 cubic ft


73 kg160 lbs

271DCF165 Battery Powered Freezer 165 liter5.8 cubic ft


57 kg125 lbs

271DCF225 Battery Powered Freezer 225 liter8 cubic ft


73 kg160 lbs

• Energy-efficient

• Automatic operation

• Thick polyurethane insulation

• Lockable lid

• Interior light in 225 liter models

• Corrosion resistant coated

steel exterior

• Patented low-frost system

• Easy to clean interior

• Adjustable thermostat

Features

Energy Consumption DC-165 DC-225@ 21°C (70°F):Refrigerator (12V)Freezer (12V)

(Amp-hr/day)723

(Amp-hr/day)830

@ 32°C (90°F):Refrigerator (12V)Freezer (12V)

(Amp-hr/day)1437

(Amp-hr/day)1745

Note: The energy test data are for comparative purposes only.Energy usage depends upon temperature, setpoints and usage.

Voltage Requirement: 12 or 24 VDCRefrigerant: R-134aPolyurethane Insulation: 110 mm (4.33")Output cable length: 2 m (6 ft)

Specifications

SunDanzer™ Battery Free Refrigerators

Energy Efficient Refrigeration

The revolutionary SunDanzer battery-free solarrefrigerator is designed for true "plug and play"operation, eliminating the need for batteries and chargecontrollers. In most applications, 95 to 120 watts of ratedpower are all that is needed. During cloudy weather,internal thermal storage keeps products cold for up to 7days, even in a tropical climate. The battery-free unit isdesigned to work in locations with at least 5 sun-hoursper day. The highly efficient refrigeration system uses avariable speed compressor and peak power tracking.

For areas with less than 5 sun-hours per day, SunWizeoffers high quality SunDanzer battery-poweredrefrigerators and freezers. Call SunWize for moreinformation.

SunDanzer cabinets are commercially produced by Electrolux ofSweden, one of the world's leading refrigeration unit manufacturers.

Part No. Description Capacity Shipping Dimensions Shipping Weight

271BFR105 Battery Free Refrigerator 105 liter

3.7 cubic ft

102W x 76D x 94H cm

40W x 30D x 37H inches

73 kg

160 lbs

• Thick polyurethane insulation

• Lockable lid

• Corrosion resistant coated steelexterior

• Easy to clean interior

• Thermal reserve status lights

• Low maintenance

• One year warranty

• Efficient chest-style cabinet

• No batteries required, no batterymaintenance

Features

Specifications

• Power requirements5.0 sun hours/day: 120 W5.5 sun hours/day: 115 W6.0 sun hours/day: 95 W

• Minimum solar insolation: 5.0 sun-hours/day• Voltage requirement: 12VDC nominal• Thermal reserve 7 days: 29°C/85°F• Refrigerant: R-134a

• Insulation: 110mm/4.33" polyurethane

LIGHTING

3/03 59

Refrigerators

In addition to being energy efficient and reliable, Sunfrost offers amenities not found inconventional household refrigerators such as food-saving, high humidity storage conditions,quiet operation, and rugged, one piece, easy-to-clean liners. Sunfrost refrigerators are customcrafted and may be ordered in a wide variety of color laminates and wood veneers. All modelsare available in 12VDC, 24VDC, 110AC or 220AC.

The RF19 refrigerator freezer has two equal sized compartments. The freezer is twice as large asthe freezer in the RF16 and the refrigerator compartment is slightly smaller. The RF19 is typicallymounted on a 13-inch high cabinet. It uses two quiet and highly efficient fans to cool the exteriorcooling coils.

The RF16 features two independent cooling systems and temperature controls. The cooling coilson the outside of the unit do not require fans. This model is usually mounted on a 13-inch highcabinet.

The RF12 is a single compressor refrigerator freezer that is passively cooled (no fans). It is typicallymounted on a 24-inch high cabinet. The matching cabinet has two large side by side drawers.

Sunfrost

Sunfrost RF19 shown mounted on a 13” cabinet

Model Energy Use/Day Energy Use/Day Dimensions Volume@70°F/21°C @90°F/32°C HxWxD (cu. feet) MSRP

RF12 Refrig/Freezer .30 KWhrs .53 KWhrs 49.50” x 34.50” x 27.75” 12 $2,199.00


RF19 Refrig/Freezer .77 KWhrs 1.03 KWhrs 66.00” x 34.50” x 27.75” 19 $3,099.00

F4 Freezer .35 KWhrs .45 KWhrs 31.50” x 34.50” x 27.75” 4 $1,550.00


* Crating is an additional charge. Please consult your dealer.

Solsum ESL

Solsum Energy Saving LampThe Solsum Energy Saving Lamp is a 12V compact fluorescent bulb with a long life and an 80%reduced consumption of electricity. Operating temperature range is 14°F to 122°F. Installs in any standard incandescent socket.

Model Voltage Wattage Current Avg. Life Span MSRP

ESL7 Cool White 12 VDC 7 W 580 mA 6000 hrs $20.00ESL11 Cool White 12 VDC 11 W 920 mA 6000 hrs. $20.00ESL 7 Warm White 12 VDC 7 W 580 mA 6000 hrs. $20.00ESL11 Warm White 12 VDC 11 W 920 mA 6000 hrs. $20.00

SolLED LED LampThe SolLED is a 12 V light emitting diode lamp that is three times brighter than a halogen lamp. Ithas a long life with a power consumption of less than 1 watt. Operating temperature range is -4°F to 122° F. Installs in any standard incandescent socket.

Model Voltage Wattage Current Lumens Avg. Life Span MSRP

SolLED .70 yellow 12 VDC .70 W 60 mA 15 100,000 hrs. $27.00SolLED .70 white 12 VDC .70 W 60 mA 11 100,000 hrs. $31.00SolLED .35 yellow 12 VDC .35 W 30 mA 8 100,000 hrs. $18.00SolLED .35 white 12 VDC .35 W 30 mA 6 100,000 hrs. $25.00

SolLED LED Lamp

Lighting

Steca



LIGHTING

3/03

Refrigerators

In addition to being energy efficient and reliable, Sunfrost offers amenities not found inconventional household refrigerators such as food-saving, high humidity storage conditions,quiet operation, and rugged, one piece, easy-to-clean liners. Sunfrost refrigerators are customcrafted and may be ordered in a wide variety of color laminates and wood veneers. All modelsare available in 12VDC, 24VDC, 110AC or 220AC.

The RF19 refrigerator freezer has two equal sized compartments. The freezer is twice as large asthe freezer in the RF16 and the refrigerator compartment is slightly smaller. The RF19 is typicallymounted on a 13-inch high cabinet. It uses two quiet and highly efficient fans to cool the exteriorcooling coils.

The RF16 features two independent cooling systems and temperature controls. The cooling coilson the outside of the unit do not require fans. This model is usually mounted on a 13-inch highcabinet.

The RF12 is a single compressor refrigerator freezer that is passively cooled (no fans). It is typicallymounted on a 24-inch high cabinet. The matching cabinet has two large side by side drawers.

Sunfrost

Sunfrost RF19 shown mounted on a 13” cabinet

Model Energy Use/Day Energy Use/Day Dimensions Volume@70°F/21°C @90°F/32°C HxWxD (cu. feet) MSRP



RF19 Refrig/Freezer .77 KWhrs 1.03 KWhrs 66.00” x 34.50” x 27.75” 19 $3,099.00



* Crating is an additional charge. Please consult your dealer.

Solsum ESL

Solsum Energy Saving LampThe Solsum Energy Saving Lamp is a 12V compact fluorescent bulb with a long life and an 80%reduced consumption of electricity. Operating temperature range is 14°F to 122°F. Installs in any standard incandescent socket.

Model Voltage Wattage Current Avg. Life Span MSRP

ESL7 Cool White 12 VDC 7 W 580 mA 6000 hrs $20.00ESL11 Cool White 12 VDC 11 W 920 mA 6000 hrs. $20.00ESL 7 Warm White 12 VDC 7 W 580 mA 6000 hrs. $20.00ESL11 Warm White 12 VDC 11 W 920 mA 6000 hrs. $20.00

SolLED LED LampThe SolLED is a 12 V light emitting diode lamp that is three times brighter than a halogen lamp. Ithas a long life with a power consumption of less than 1 watt. Operating temperature range is -4°F to 122° F. Installs in any standard incandescent socket.

Model Voltage Wattage Current Lumens Avg. Life Span MSRP

SolLED .70 yellow 12 VDC .70 W 60 mA 15 100,000 hrs. $27.00SolLED .70 white 12 VDC .70 W 60 mA 11 100,000 hrs. $31.00SolLED .35 yellow 12 VDC .35 W 30 mA 8 100,000 hrs. $18.00SolLED .35 white 12 VDC .35 W 30 mA 6 100,000 hrs. $25.00

SolLED LED Lamp

Lighting

Steca


LIGH

TING

60 3/03

Energy Saving Lamps - 115VACTop quality Edison base fluorescent lamps offer tremendous energy savings as compared totypical incandescent bulbs. Compact design can be used in most lamps and screw-in fixtures.Single use assembly with bulb. Installs in standard incandescent socket.

Model Watts Lumens Average Life Dimensions MSRP

ESL18 18 W 990 5000 hrs. 2” x 6.4” $6.75ESL26 26 W 1430 5000 hrs. 2” x 7.0” $8.50

ESL 18

Lighting

LED Outdoor Wall or Ceiling Lamp This unit contains 28 white LED's that are comparable to a 13-watt fluorescent or a 60-wattincandescent lamp. Ideal for bus stops, porches, and outbuildings. Housed in an outdoor, vandalresistant enclosure.

Model Voltage Current Dimensions Weight (lbs) MSRP

WP28 12 VDC 200 ma 8.5” x 4.5” x 4” 2 $239.00

LED Lamp

SunWize LED Fixture

SunWize 12 LED FixtureThis waterproof fixture uses 12 high-tech bright white LED's. The fixture features black powdercoated aluminum body with pivot adjustment, sealed 3" diameter glass lens and a ground stake.LED circuit is not harmed by reverse polarity. 100,000 hour rated life.

Model Voltage Current Dimensions Weight (lbs) MSRP12 LED Fixture 12V DC 0.08A 3" x 4" x 12' 1.5 $109.00

SunWize Spotlight System

SunWize Solar 12-LED Spotlight System This self-contained lighting system allows dusk to dawn operation of a 12 LED spotlight.Designed for flagpole lighting, small signage, entrance-walkway and path lighting. Fullyassembled system includes a 5-watt solar module, 7Ah sealed battery, automatic light controllerwith adjustable timer, and a 12 LED spotlight with 10 ft cable. The black powder coatedaluminum vandal resistant housing can mount to the wall or a pole. Includes two adjustable poleclamps. System requires minimum 4 hours sunlight for dusk/dawn operation. Ten-year solarmodule warranty, five-year light controller warranty.

Model Voltage Dimensions Weight (lbs) MSRPSpot Light System 12V DC 13" x 8.5" x 8.5" 14.0 lbs $499.00

Solar 4-LED FloodlightOutdoor Dusk to Dawn Solar/LED floodlight features four powerful bright white LED’s mounted in areflective parabolic housing. Wide coverage-use fixture can be aimed in all directions withmounting options of 12” tall ground stake or place atop a wood post or sign. Includes solar panel,4-AA / 900mAh Ni-Cad batteries. One-year warranty.

Model Dimensions Weight (lbs) MSRPSL4W 10.0” x 5.5” x3” 2.0 $135.00Solar Path Light


LIGH

TING

60 3/03

Energy Saving Lamps - 115VACTop quality Edison base fluorescent lamps offer tremendous energy savings as compared totypical incandescent bulbs. Compact design can be used in most lamps and screw-in fixtures.Single use assembly with bulb. Installs in standard incandescent socket.

Model Watts Lumens Average Life Dimensions MSRP

ESL18 18 W 990 5000 hrs. 2” x 6.4” $6.75ESL26 26 W 1430 5000 hrs. 2” x 7.0” $8.50

ESL 18

Lighting

LED Outdoor Wall or Ceiling Lamp This unit contains 28 white LED's that are comparable to a 13-watt fluorescent or a 60-wattincandescent lamp. Ideal for bus stops, porches, and outbuildings. Housed in an outdoor, vandalresistant enclosure.

Model Voltage Current Dimensions Weight (lbs) MSRP

WP28 12 VDC 200 ma 8.5” x 4.5” x 4” 2 $239.00

LED Lamp

SunWize LED Fixture

SunWize 12 LED FixtureThis waterproof fixture uses 12 high-tech bright white LED's. The fixture features black powdercoated aluminum body with pivot adjustment, sealed 3" diameter glass lens and a ground stake.LED circuit is not harmed by reverse polarity. 100,000 hour rated life.

Model Voltage Current Dimensions Weight (lbs) MSRP12 LED Fixture 12V DC 0.08A 3" x 4" x 12' 1.5 $109.00

SunWize Spotlight System

SunWize Solar 12-LED Spotlight System This self-contained lighting system allows dusk to dawn operation of a 12 LED spotlight.Designed for flagpole lighting, small signage, entrance-walkway and path lighting. Fullyassembled system includes a 5-watt solar module, 7Ah sealed battery, automatic light controllerwith adjustable timer, and a 12 LED spotlight with 10 ft cable. The black powder coatedaluminum vandal resistant housing can mount to the wall or a pole. Includes two adjustable poleclamps. System requires minimum 4 hours sunlight for dusk/dawn operation. Ten-year solarmodule warranty, five-year light controller warranty.

Model Voltage Dimensions Weight (lbs) MSRPSpot Light System 12V DC 13" x 8.5" x 8.5" 14.0 lbs $499.00

Solar 4-LED FloodlightOutdoor Dusk to Dawn Solar/LED floodlight features four powerful bright white LED’s mounted in areflective parabolic housing. Wide coverage-use fixture can be aimed in all directions withmounting options of 12” tall ground stake or place atop a wood post or sign. Includes solar panel,4-AA / 900mAh Ni-Cad batteries. One-year warranty.

Model Dimensions Weight (lbs) MSRPSL4W 10.0” x 5.5” x3” 2.0 $135.00Solar Path Light

LIGHTING

3/03

Lighting

PL Compact Fluorescents

Economy Fixture – Fluorescent IndoorThe slim line Trilight, 12 volt DC fixture offers a unique design allowing operation of one, two orthree 8 watt tubes. If one tube fails, the others will still work. Low power consumption; one tubeis <0.5 amp, three tubes are 0.85 amps (supplied with one tube). Includes on/off switch andunbreakable lens.

Rated Design WeightModel Voltage Tube Life Lumens Dimensions (lbs) MSRP

KL8 12 VDC 5000+ hours 400 15” x 3” x 1” 1 $20.008W Replacement Lamp $13.50

Replacement Lamps-Compact FluorescentTwin tube “PL” lamps are 4100K-color temperature. For fixture models 1001 and 2020.

Model Watts Average Life Lumens Base Length MSRP

RL001 13 W 10,000 hrs. 900 GX23 7.3” $16.00

RL002 36 W 10,000 hrs. 2900 2G11 16” $19.00

RL004 7 W 10,000 hrs. 450 G23 5.25” $14.00

RL001 (top) and RL002Compact Fluorescents

Trilight

Outdoor Wall Ceiling Fixture

Wall Ceiling Fixture – Fluorescent OutdoorAttractive and virtually indestructible, this wall/ceiling mount fixture is rated for use in wetlocations and features a molded prismatic polycarbonate lens and internal specular aluminumreflector. Fixture body can accept conduit wiring and includes energy efficient ballast and PLcompact fluorescent lamp. Fixture of choice for transit shelter lighting.

Model Voltage Lamp Watts Current Dimensions Weight (lbs) MSRP

2020-7 12 VDC 7 W 0.65 A 11” x 5” x 3” 2 lbs. $110.002020-13 12 VDC 13 W 1.25 A 11” x 5” x 3” 2 lbs. $120.00

Outdoor Floodlight

Floodlight – Fluorescent Outdoor

Directional floodlight is ideal for signs, wall washing, driveway or security lighting. Fixtures featureblack powder coated aluminum housing with 1/2” NPT swivel mount, a specular aluminum parabolicreflector, clear polymer lens, solid state electronic ballast and compact PL lamp. 24 VDC special order.

Model Voltage Lamp Watts Current Dimensions MSRP

1001-13 12 VDC 13 W 1.1 A 9.3” x 6.6” x 4.6” $122.501001-36 12 VDC 36 W 2.2 A 18.0” x 6.6” x 4.6” $275.00

Economy Floodlight – Fluorescent Outdoor

Non-metallic molded black fixture features a self contained ballast, a polished reflector, clear lensscrew cover and 1/2” NPT pivot mount. Twin tube replacement lamps are 4100K color temperature,10,000 hours average life.

Model Voltage Lamp Watts Dimensions Weight (lbs) MSRP

LIT-ELF12/9 12 VDC 9 W 9.3” x 4” x 4” 1.5 $87.50LIT-ELF12/13 12 VDC 13 W 9.3” x 4” x 4” 1.5 $87.50

Replacement Lamps-Compact Fluorescent 4 Pin Base

Model Watts Lumens Base Length MSRP

PL9 9 600 2G7 5.7" $10.00

PL13 13 900 2GX7 6.2" $11.50

Outdoor Economy Floodlight


Lighting

LIGH

TING

62 3/03

SunWize LPS Roadway Fixture

SunWize® 'SRX' LPS Roadway Fixture Low Pressure Sodium (LPS) light fixtures are useful for roadway, security or area lighting. Theseconstant-output LPS lamps produce monochromatic (yellow-orange) light, delivering the highestlumen per watt rating, even in freezing climates. Outdoor fixture housing is corrosion resistant, diecast aluminum for 2" pipe-arm mounting with hinged unbreakable prismatic lens. Designed for DCoperation. Includes DC ballast and SOX type-LPS 35 or 55W lamp.

DC Input Current Lamp Approx. WeightModel Voltage Draw Wattage Lumens Dimensions (lbs) MSRP

SRX-LPS 35 12V DC 3.0A 35 4800 27" x 7.5" x 9" 10.0 $470.00SRX-LPS 55 24V DC 2.0A 55 8000 27" x 7.5" x 9" 10.0 $529.00

Lamps - Low Pressure Sodium

Model Watts Lumens Base Length Average Life MSRP

SOX-35 35W 4800 lumens T17 8.5" long 16,000 hours $58.00

SOX-55 55W 8000 lumens T17 12.2" long 16,000 hours $99.00Low Pressure Sodium Lamp

DC Ballasts – LPSEnergy efficient, long life, solid state electronic ballast for use with SOX-LPS lamps.

Model Wattage Voltage Current Dimensions Weight (lbs) MSRP

DCB-SOX35 35W 12V DC 3.0A 1.5” X 1.5” X 5” 1.0 $85.00

DCB-SOX55 55W 24V DC 2.0A 1.5” X 2.5” X 9” 2.0 $105.00LPS DC Ballast

DC Ballasts – FluorescentEnergy efficient, long life, solid state electronic 12VDC ballast for use with single compactfluorescent lamps. 24-volt models are also available with minimum order. All are 2-wireconnection.

Model Wattage Dimensions Weight (oz) MSRP

2D12-1-9 5/7/9 1.9” x 1.9” x 2.5” 7 $35.00

2D12-1-13 13 1.9” x 1.9” x 2.5” 7 $39.00

2D12-1-32 18-40 5.4” x 1.9” x 1.4” 14 $59.00

Fluorescent DC Ballast

SunWize DC-PIR Floodlight

SunWize® DC-PIR Floodlight The DC-PIR Floodlight is a self-contained 12 V floodlight that requires no assembly and is readyto install. Just connect a solar module. The all aluminum, wall pack enclosure design can also bepole mounted. The sensor and fixture can be aimed up/down or left/right. The 12V PIR motionsensor allows day or night operation with adjustable 1-18 minute self-resetting timer. Includes PVcharge controller, 13W fluorescent floodlight and a sealed 17AH battery. Use with an OEM 10, 20or 40W module depending on regional location and frequency of operation.

Model Voltage Current Enclosure Size Weight (lbs) MSRP

DC-PIR-13W 12VDC 1.2A 11” x 9” x 5” 10.0 $449.00



Lighting

LIGH

TING

62 3/03

SunWize LPS Roadway Fixture

SunWize® 'SRX' LPS Roadway Fixture Low Pressure Sodium (LPS) light fixtures are useful for roadway, security or area lighting. Theseconstant-output LPS lamps produce monochromatic (yellow-orange) light, delivering the highestlumen per watt rating, even in freezing climates. Outdoor fixture housing is corrosion resistant, diecast aluminum for 2" pipe-arm mounting with hinged unbreakable prismatic lens. Designed for DCoperation. Includes DC ballast and SOX type-LPS 35 or 55W lamp.

DC Input Current Lamp Approx. WeightModel Voltage Draw Wattage Lumens Dimensions (lbs) MSRP

SRX-LPS 35 12V DC 3.0A 35 4800 27" x 7.5" x 9" 10.0 $470.00SRX-LPS 55 24V DC 2.0A 55 8000 27" x 7.5" x 9" 10.0 $529.00

Lamps - Low Pressure Sodium

Model Watts Lumens Base Length Average Life MSRP

SOX-35 35W 4800 lumens T17 8.5" long 16,000 hours $58.00

SOX-55 55W 8000 lumens T17 12.2" long 16,000 hours $99.00Low Pressure Sodium Lamp

DC Ballasts – LPSEnergy efficient, long life, solid state electronic ballast for use with SOX-LPS lamps.

Model Wattage Voltage Current Dimensions Weight (lbs) MSRP

DCB-SOX35 35W 12V DC 3.0A 1.5” X 1.5” X 5” 1.0 $85.00

DCB-SOX55 55W 24V DC 2.0A 1.5” X 2.5” X 9” 2.0 $105.00LPS DC Ballast

DC Ballasts – FluorescentEnergy efficient, long life, solid state electronic 12VDC ballast for use with single compactfluorescent lamps. 24-volt models are also available with minimum order. All are 2-wireconnection.

Model Wattage Dimensions Weight (oz) MSRP

2D12-1-9 5/7/9 1.9” x 1.9” x 2.5” 7 $35.00

2D12-1-13 13 1.9” x 1.9” x 2.5” 7 $39.00

2D12-1-32 18-40 5.4” x 1.9” x 1.4” 14 $59.00

Fluorescent DC Ballast




DC-PIR-13W 12VDC 1.2A 11” x 9” x 5” 10.0 $449.00

LIGHTING

3/03

Lighting




DC-PIR-13W 12VDC 1.2A 11” x 9” x 5” 10.0 $449.00

SunWize® Solar “Outbuilding” Light – PIR

This one of a kind lighting package is totally self-contained and intended for remote facilitieswithout power. The outbuilding light was created for park and recreation departments for use inpublic restrooms, equipment and storage shelters, and many other uses. Unique cost savingdesign features plug and play installation, incorporating a DC fluorescent light, solar chargecontroller, sealed battery pack, 10 ft. connection cable & mounting hardware. Includes a passiveinfrared (PIR) motion detector with adjustable run time for day or night only operation. Use ESL11 screw-type bulb for replacement.

Model Voltage Current Lamp Watts Battery size Dimensions MSRP

OBFL-11 12 VDC 1.0 A 11 W 7 Ah 8” x 8” x 8” $299.00

OBFL light w/motion detector

12VDC Motion Sensor- PIRThis passive infrared motion sensor detects heat and movement to activate 12 VDC lighting.Rated for outdoor use in wet locations. Includes sensitivity adjustment to deter false trigger andwill allow day or night only operation. Adjustable timer for 1 to 18 minutes, unit is self-resettingduring movement. Includes swivel base. UL listed.

Model Voltage Max. Load Current Dimensions MSRPPIR-2000/12 12 VDC 10 A 9.0” x 5.5” x 1.6“ $99.00Motion Sensor

“Outbuilding” Light System

SunWize® Solar “Outbuilding” Light – System

Complete solar lighting package with OBFL-11outbuilding/PIR light including Uni-Solar modulewith additional cable and flush mounting brackets. Select solar power kits depending on regional(or seasonal) use. Systems can provide up to 4 hours of timed operation per night.

Model Solar Wattage Recommended Geographic Use MSRP

OBFL-11/05W 5 W Southern US $369.00

OBFL-11/11W 11 W Southern US Latitudes $429.00

OBFL-11/21W 21 W Northern US Latitudes $489.00

OBFL-11/32W 32 W Canada $529.00



LIGHTING

3/03 63

Lighting

Outdoor Solar Lantern-FluorescentThe popular hanging lantern design is perfect for camping or emergency lighting. Durablemolded plastic is waterproof and self contained with a sealed battery and dual 6 watt lamps.Features a one or two lamp selection switch, 3 watt solar module with cord/plug, 115 VACadapter and charging LED. Built-in circuitry prevents battery overcharge and over-discharge.Solar panel packaged separately. Models for export (230VAC adapter) available.

Model MSRPOutdoor Solar Lantern $69.00

Fluorescent Solar Lantern

The UNI-KIT is a durable lighting system providing extended lighting hours. Simple plug-inconnections make it easy to install. A Power Control Center manages the system and easy toread indicators display current battery conditions. Each unit is complete with a 25-foot wire fromthe modules to the Power Control Center, a 10-foot wire for connecting lights, plus a 15-foot wire from the Power Control Center to the lights. UL listed. The Power Control Centercarries a one-year warranty. These systems can also power a 12 volt radio or television. Batterysold separately.

Model Rated Power Battery Capacity Performance MSRP

UNI-KIT 30 32 W 55-65 Ah 12-16 lamp hours $429.00UNI-KIT 60 64 W 90-120 Ah 24-32 lamp hours $679.00

UNI-KIT 30




OBFL-11 12 VDC 1.0 A 11 W 7 Ah 8” x 8” x 8” $299.00











OBFL-11/32W 32 W Canada $529.00

Uni-Solar Lighting Kits


LIGHTING

3/03 63

Lighting

Outdoor Solar Lantern-FluorescentThe popular hanging lantern design is perfect for camping or emergency lighting. Durablemolded plastic is waterproof and self contained with a sealed battery and dual 6 watt lamps.Features a one or two lamp selection switch, 3 watt solar module with cord/plug, 115 VACadapter and charging LED. Built-in circuitry prevents battery overcharge and over-discharge.Solar panel packaged separately. Models for export (230VAC adapter) available.

Model MSRPOutdoor Solar Lantern $69.00

Fluorescent Solar Lantern

The UNI-KIT is a durable lighting system providing extended lighting hours. Simple plug-inconnections make it easy to install. A Power Control Center manages the system and easy toread indicators display current battery conditions. Each unit is complete with a 25-foot wire fromthe modules to the Power Control Center, a 10-foot wire for connecting lights, plus a 15-foot wire from the Power Control Center to the lights. UL listed. The Power Control Centercarries a one-year warranty. These systems can also power a 12 volt radio or television. Batterysold separately.

Model Rated Power Battery Capacity Performance MSRP

UNI-KIT 30 32 W 55-65 Ah 12-16 lamp hours $429.00UNI-KIT 60 64 W 90-120 Ah 24-32 lamp hours $679.00

UNI-KIT 30




OBFL-11 12 VDC 1.0 A 11 W 7 Ah 8” x 8” x 8” $299.00











OBFL-11/32W 32 W Canada $529.00

Uni-Solar Lighting Kits

ELECTRICAL/HARDW

ARE

3/03 65

Electrical/Switchgear

PCB-10 Combiner Box

PV System Combiner BoxThe PCB10 is designed to combine multiple PV source circuits into one output circuit. Thiscombiner allows up to10 fused input circuits in a lockable, conduit-ready and rainproof 3Renclosure. PCB10 combiners are UL listed for 12, 24 or 48 VDC PV systems, maximum opencircuit voltage of 125VDC. Each combiner circuit can accept up to 15 amp fuses, type MDA orABC with the maximum combined PV source circuit current rating of 64 amps. Each input circuitis ‘ZNR’ surge protected and will accept #10AWG conductors including ground bar. The positiveand negative outputs are equipped with dual rated #1/0 AWG lugs.

Connect Energy

Combiner Model Dimensions Weight (lbs) MSRP

PCB10 10” x 8” x 4” 7.0 $229.00Fuse Model Current Rating Dimensions MSRPPCBF-10 10 A 0.25” x 1.25” $1.20PCBF-15 15 A 0.25” x 1.25” $1.20PCBF-5 5 A 0.25” x 1.25” $1.20PCBF-6 6 A 0.25” x 1.25” $1.20PCBF-8 8 A 0.25” x 1.25” $1.20

PSPV Combiner Box

PV Array CombinerThe PSPV Power System PV Array Combiner provides series overcurrent protection of PV modulecircuits allowing NEC compliant installation. Includes space for up to twelve 125 VDC ratedbreakers or eight 600 VDC rated fuse holders. Includes two positive output bus bars with two#1/0 terminals for single or dual output circuits. The type 3R outdoor rainproof enclosure can bemounted vertically or inclined to 14 degrees. Enclosure only without breakers or fuses.


PSPV 13.1” x 9.2” x 3.5” 6 lbs $139.00

PV Array Breakers for PSPVDIN rail snap-in mount with #2 AWG setscrew type compression terminals. UL listed. Maximumof twelve breakers. Approved for two wires per terminal. Ten-year warranty.

OBPV-6 PV breaker, 6 amp, 125 VDC $12.00OBPV-9 PV breaker, 9 amp, 125 VDC $12.00OBPV-10 PV breaker, 10 amp, 125 VDC $12.00OBPV-15 PV breaker, 15 amp, 125 VDC $12.00OBPV-30 PV breaker, 30 amp, 125 VDC $12.00

Fuseholder – 600 VDC for PSPV – maximum of eight fusesUSM-1 Single pole for DIN rail mounting. UL listed. Finger-safe touch design,

flip-up fuse cartridge for 13/32” x 1.5” fuses. 0.7” x 3” x 2.3” $15.00

Fuses – 600 VDC, 13/32” x 1.5” fast acting 100,000A interrupt rating.KLKD6 6 amps $12.00KLKD10 10 amps $12.00KLM12 12 amps $25.00KLM20 20 amps $25.00

OutBack Power Systems

PSPV PV Array Breakers

PSSB CombinerSpecifically designed to work with Sunny Boy inverter systems. The PSSB allows connection of up tosix low voltage sub-arrays in series to form a high voltage PV array. Each sub-array can have amaximum open circuit voltage of 100 VDC. Includes one segmented 600 VDC breaker assembly, withspace for one additional OBSP-15 or a dual pole AC breaker for the Sunny Boy output. Eliminates thehazards of wiring high voltage PV arrays. Aluminum, raintight, NEMA 3R outdoor enclosure.

Model Weight (lbs) MSRP

PSSB 13.1” x 9.2” x 3.5” 6 lbs $249.00OBSB-15 Segmenting breaker assembly, 6 pole 15A-100V DC/pole $110.00PSSB-MP Mounting Panel for PSSB + Sunny Boy inverter, 34” x 17 x 1” $99.00PSSB Combiner



ELECTRICAL/HARDW

ARE

3/03


PCB-10 Combiner Box

PV System Combiner BoxThe PCB10 is designed to combine multiple PV source circuits into one output circuit. Thiscombiner allows up to10 fused input circuits in a lockable, conduit-ready and rainproof 3Renclosure. PCB10 combiners are UL listed for 12, 24 or 48 VDC PV systems, maximum opencircuit voltage of 125VDC. Each combiner circuit can accept up to 15 amp fuses, type MDA orABC with the maximum combined PV source circuit current rating of 64 amps. Each input circuitis ‘ZNR’ surge protected and will accept #10AWG conductors including ground bar. The positiveand negative outputs are equipped with dual rated #1/0 AWG lugs.

Connect Energy

Combiner Model Dimensions Weight (lbs) MSRP

PCB10 10” x 8” x 4” 7.0 $229.00Fuse Model Current Rating Dimensions MSRPPCBF-10 10 A 0.25” x 1.25” $1.20PCBF-15 15 A 0.25” x 1.25” $1.20PCBF-5 5 A 0.25” x 1.25” $1.20PCBF-6 6 A 0.25” x 1.25” $1.20PCBF-8 8 A 0.25” x 1.25” $1.20

PSPV Combiner Box

PV Array CombinerThe PSPV Power System PV Array Combiner provides series overcurrent protection of PV modulecircuits allowing NEC compliant installation. Includes space for up to twelve 125 VDC ratedbreakers or eight 600 VDC rated fuse holders. Includes two positive output bus bars with two#1/0 terminals for single or dual output circuits. The type 3R outdoor rainproof enclosure can bemounted vertically or inclined to 14 degrees. Enclosure only without breakers or fuses.


PSPV 13.1” x 9.2” x 3.5” 6 lbs $139.00

PV Array Breakers for PSPVDIN rail snap-in mount with #2 AWG setscrew type compression terminals. UL listed. Maximumof twelve breakers. Approved for two wires per terminal. Ten-year warranty.

OBPV-6 PV breaker, 6 amp, 125 VDC $12.00OBPV-9 PV breaker, 9 amp, 125 VDC $12.00OBPV-10 PV breaker, 10 amp, 125 VDC $12.00OBPV-15 PV breaker, 15 amp, 125 VDC $12.00OBPV-30 PV breaker, 30 amp, 125 VDC $12.00

Fuseholder – 600 VDC for PSPV – maximum of eight fusesUSM-1 Single pole for DIN rail mounting. UL listed. Finger-safe touch design,

flip-up fuse cartridge for 13/32” x 1.5” fuses. 0.7” x 3” x 2.3” $15.00

Fuses – 600 VDC, 13/32” x 1.5” fast acting 100,000A interrupt rating.KLKD6 6 amps $12.00KLKD10 10 amps $12.00KLM12 12 amps $25.00KLM20 20 amps $25.00


PSPV PV Array Breakers

PSSB CombinerSpecifically designed to work with Sunny Boy inverter systems. The PSSB allows connection of up tosix low voltage sub-arrays in series to form a high voltage PV array. Each sub-array can have amaximum open circuit voltage of 100 VDC. Includes one segmented 600 VDC breaker assembly, withspace for one additional OBSP-15 or a dual pole AC breaker for the Sunny Boy output. Eliminates thehazards of wiring high voltage PV arrays. Aluminum, raintight, NEMA 3R outdoor enclosure.


PSSB 13.1” x 9.2” x 3.5” 6 lbs $249.00OBSB-15 Segmenting breaker assembly, 6 pole 15A-100V DC/pole $110.00PSSB-MP Mounting Panel for PSSB + Sunny Boy inverter, 34” x 17 x 1” $99.00PSSB Combiner

ELEC

TRIC

AL/

HARD

WAR

E

3/03


OutBack Power System DC

PSDC Enclosure

PSDC Enclosure The PSDC indoor enclosure is designed to integrate the DC overcurrent protection and wiringneeds of inverter/battery, PV charging systems and DC load distribution. Removable side panelsallow for direct DC wiring access for up to 4 FX or 2 SW/DR inverters. The PSDC includesmounting provisions for up to ten small (0.75” wide) and six medium (1” wide) or four large (1.5”wide) DC breakers. Charge controllers can be installed directly on top of the enclosure, or side-mounted by adding a charge controller bracket (CCB). Includes one 500-amp/50mV shunt,battery breaker, one combined ground/negative terminal bus bar and one isolated positive busbar, 3/4”, 1” and 2” knockouts. Forest green powder coated steel. ETL listed.

Model DC Breaker Dimensions Weight (lbs) MSRP

PSDC-250 250 amp 32.5” x 16” x 9” 38 $519.00PSDC-175 175 amp 32.5” x 16” x 9” 38 $519.00

DC Circuit Breaker 125 VDCThe PSDC holds a maximum of four large 1.5” breakers, six medium 1” breakers or ten small.75” breakers. The Amps Interrupt Capacity, AIC, rating is in accordance with UL 489. 125 VDC.

Current AIC Stud Space Model Rating Rating Terminal Size Required MSRP

OBDC-250 250 amp 25K at 65 VDC 3/8” stud One 1.5” $119.00OBDC-175 175 amp 25K at 65 VDC 3/8” stud One 1.5” $119.00OBDC-100 100 amp 25K at 65 VDC 1/4” stud One 1.0” $59.00OBDC-60 60 amp 7.5K at 80 VDC 1/4” stud One .75” $29.00OBDC-40 40 amp 7.5K at 80 VDC 1/4” stud One .75” $29.00OBDC-30 30 amp 7.5K at 80 VDC 1/4” stud One .75” $25.00OBDC-15 15 amp 7.5K at 80 VDC 1/4” stud One .75” $25.00OBDC-10 10 amp 7.5K at 80 VDC 1/4” stud One .75” $25.00

Charge Controller BracketAllows up to two OutBack MX60 controllers or three Xantrex C-Series to be mounted on eitherside of the PSDC enclosure with matching knockouts (up to three MX60, C-series or two RVPPSolar Boost units can be top mounted on the PSDC without the CCB).

Model MSRPCCB $39.00

OBDC-GFP/2 DC Ground Fault Protection SystemThe DC-GFP/2 is required by the NEC for PV arrays mounted on residential dwelling roofs. It canbe used with the PSDC or PSR. It protects wiring and system components for one or two PVarrays up to 60 amps at 125 VDC maximum. Requires three small breaker spaces in the PSDC.Includes a ground bus bar, neutral and ground connection wiring and mounting hardware. UL listed for a maximum of 125 VDC.

Model MSRP

OBDC-GFP/2 $129.00

CCB Bracket (shown mountedon the PSDC)

OBDC – GFP System

Terminal and Ground Bus BarsUse for adding more wire terminations or for isolating multiple positive/negative circuits. All models havethree #1/0 to 14 AWG and eight #6 to 14 AWG compression screw terminals (no ring lugs required).

Model Version MSRP

TBB Terminal bus bar with black insulators $19.00TBB-R Terminal bus bar with red insulators $19.00TBB-W Terminal bus bar with white insulators $19.00GBB Ground Bus bar - uninsulated $15.00GBB Ground Bus Bar

DC Overcurrent Protection


ELECTRICAL/HARDW

ARE

3/03


PSMP Mounting Plate

PSAC Enclosure The PSAC indoor enclosure is designed to integrate the AC overcurrent protection wiring needsof input/output from inverter/generator systems and AC load distribution. Removable side panelsallow for direct AC wiring access for up to 4 FX or 2 SW/DR inverters. The PSAC includes twobrackets with DIN rail mounts for up to eight Square-D QOU type AC breakers on each bracket.Includes one AC output bypass breaker assembly, a separate ground, isolated neutral and hotterminal bus bar standard. Space is available to install an optional X-240 auto transformer andadditional AC input/output/bypass breaker assemblies. Forest green powder coated steel. ETL listed.

Model Inverter Type AC Breaker Dimensions Weight MSRP

PSAC-60 One SW Series/FX Series 60 amp, 120VAC 32.5” x 10.5” x 9” 32 lbs $369.00PSAC-30 Small Inverters (DR Series) 30 amp, 120 VAC 32.5” x 10.5” x 9” 32 lbs $369.00

Circuit Breakers ‘QOU’ typeUL listed, 120/240 VAC, 48VDC, single pole ‘QOU’ breakers feature a ‘Visi-trip’ indicator and areintended for flush or surface mounting with reversible lugs, or DIN rail mount. Includes mountingfeet for convenient panel attachment. Wire lug size accepts #14 to # 2AWG.

Model Current Rating MSRPQOU10 10 A $17.50QOU15 15 A $17.50QOU20 20 A $21.50QOU30 30 A $21.50QOU40 40 A $28.00QOU60 60 A $28.00QOU30-2 (2-pole) 30 A $39.00QOU60-2 (2-pole) 60 A $39.00

AC Input/Output/Bypass Assemblies - PSACPacked as a complete kit with detailed instructions and drawings. Includes safety interlock.Allows bypassing of an inverter for maintenance or repair while maintaining power to AC loadssupplied from a generator or utility grid. Includes single and 2-pole QOU circuit breaker, safetyinterlock, wire, mounting screws and service lug.

Model Inverter Type AC Breaker MSRP

AC-IOB-60 One FX2000/SW series 60 amp $85.00AC-IOB-60D For two FX2000 or SW inverters 60 amp $159.00AC-IOB-30 One DR or other small inverter 30 amp $85.00AC-IOB-30D For two DR or other small inverters 30 amp $159.00

PSMP Mounting Plate and PSA Inverter Adapter for the PSDC and PSACThe PSMP is a two-piece power system mounting plate, pre-drilled, for PSAC and PSDC and up tofour FX or two SW or DR inverter/chargers. Split in half for UPS shipping. Forest green powdercoated steel. Includes fasteners.

The PSA adapts the side opening of a PSAC or PSDC to match the PS series inverter/charger.


PSMP 36” x 50” x 1” 46 lbs $179.00

PSA PS series inverter adapter plate for PSAC and PSDC $19.00

PSAC Enclosure

AC IOB Assemblies

QOU Type Circuit Breakers

OutBack Power System AC


ELEC

TRIC

AL/

HARD

WAR

E

68 3/03


Surge CapacitorsSurge capacitors help prevent damage to sensitive AC electrical equipment by controlling highvoltage surges too light or fast for a surge arrestor. They react continually with a slight voltageincrease and no delay. Includes 18” long-#12/2 wires.

Model Rated Voltage Dimensions MSRP

AC Capacitor 125/250 VAC 2.25” diam. x 4.5” $55.00

Lightning Arrestor shown withtop mount bracket (l) and sidemount bracket (r).

Lightning ArrestorsSilicon Oxide Varistor (SOV) lightning surge arrestors can handle high current surges that are toolarge for an MOV or capacitor. They provide protection to electrical equipment by reducingproblems due to lightning strikes or power surges. Surge arrestors react in as little as fivenanoseconds and begin to conduct when voltage rises above the nominal line voltage after aspecific time delay and handle an unlimited number of surges. The waterproof case is designedto install into a 1/2” knockout opening. Includes 18” long #12AWG wires. UL listed.

Model MSRPSide Mount $3.00Top Mount $9.00

Arrestor Mounting Bracket

Model Description Rated Voltage Dimensions Weight MSRP

LA302DC DC Arrestor up to 250VDC 2.25” diam. x 2.25” 1.0 $35.00LA602DC DC Arrestor up to 600VDC 2.25” diam. x 4.50” 1.5 $39.00LA302R AC Arrestor up to 300VAC 2.25” diam. x 2.25” 1.0 $35.00

Fuse Block System - ATO/ATC This fuse block system features a stylish, clear insulating cover that protects conductive partsand includes label recess for marking. Tin-plated copper buses allow 30 amp fuse rating percircuit, 100A max rating per block. Two styles -6 circuit with/without NEG bus, less fuses.

Model Description Dimensions MSRP

5025 6 circuit W/ Neg. bus 2.0” x 6.0” $27.005028 6 circuit 2.0” x 4.0” $24.00

Fuse Holder – In Line , ATO/ATCFor direct in line wiring for one type ATO/ATC fuse holder rated 30A max, with 4” #12AWG lead wires.

Model Description MSRP

46021 Fuse Holder $2.50 46019 Fuse Cover Clear $1.25

Fuse Holder – Water Resistant ATO/ATC Sealed, weather resistant body and cap with mounting tab for one type ATO/ATC fuse, rated 30amp max. with 8” x #12AWG lead wires.


46033 Water Resistant Fuse Holder $5.00

5025 Fuse Block

In Line Fuse Holder

Water Resistant Fuse Holder


ELEC

TRIC

AL/

HARD

WAR

E

70 3/03


DC Ammeter – AnalogUseful for measuring current flow from PV or wind sources to battery-draws 1ma. Accuracy 3%,2-3/4” face-flush mount, simple 2-wire connection from shunt.

Model Scale Dimensions Weight (lbs) MSRP

8005 25A 2.8” x 2.4” 0.24 $37.00

DC Voltmeter – AnalogMeter with 2-3/4” face-flush mount, 3% accuracy, simple 2-wire connections, draws 1ma.

Model Voltage Scale Dimensions Weight (lbs) MSRP

8003 8-16V DC 2.8” x 2.4” 0.23 $33.008240 18-32V V DC 2.8” x 2.4” 0.23 $42.00

Analog Meter PanelsAttractive slate gray powder coated 1/8’ aluminum panels flush mount 2-3/4” analog (or digital) meters.

Model Type Dimensions Weight MSRP

8013 Single Meter 3.75” x 5.25” 0.22 $23.008014 Dual Meters 7.50” x 5.25” 0.36 $29.00

DC Analog Ammeter

DC Analog Voltmeter

Analog Meter Mounting Panels


ELECTRICAL/HARDW

ARE

3/03

DC Battery SwitchUL listed to 32 VDC, these compact, high-amperage, vapor-proof rotary on/off switches allow ameans of disconnection between battery systems and DC loads up to 300 amps continuousrating (400A intermittent). Rugged molded Lexan® case design allows flush or surface mounting.Model 9001 allows switching from or combining two separate battery banks.

Model Dimensions Description MSRP

9003 4.0” x 4.0” x 2.7” ON/OFF $41.009001 4.0” x 4.0” x 2.7” OFF, #1, #2, BOTH $49.00

Mini-Battery SwitchVapor proof case design and small size allows compact installations for indoor or outdoor use.For use with 12/24 VDC battery systems, includes color-coded label with international ON-OFFsymbols. Contoured knob rotates 360 degrees for ease of operation. Rated 250 ampscontinuous, 600A surge, with 3/8” stud terminals.

Model Dimensions MSRP

9006 2.7” x 2.7” $29.00

DC Circuit Breaker – WaterproofWeatherproof, vapor proof DC circuit breaker combines switching and circuit protection functioninto one unit. Useful with 12/24/48V DC battery systems, this panel-mount, switchable-manualreset thermal breaker meets SAE marine & ignition standards. Designed to trip on fault currenteven if lever is held ‘ON’. High torque 5/16” studs accept up to # 2/0 AWG cables.

Model Current Rating Dimensions Weight MSRP

7129 100A 2.3” x 3.4” x 1.8 0.50 lbs $45.007033 150A 2.3” x 3.4” x 1.8 0.50 lbs $45.00

Solid Neutral KitIsolated solid neutral bus contains three AL. lugs for # 3-14AWG. Field installable for use withheavy duty disconnect switches.


SN03 1 $49.00


Waterproof DC Circuit Breaker

DC Battery Switch

Mini-Battery Switch

Solid Neutral Kit

250V Safety Switch

Safety Switches – 250V Fusible/OutdoorGeneral duty UL listed safety disconnect switches are rated outdoor NEMA 3R with externallockable switch handle. These safety switches serve as service disconnects and overcurrentdevices for AC or DC systems rated to 250 volts. Switches include main lugs, neutral bus andground screw.

Model # Poles Max Current Wire Size Dimensions Weight (lbs) MSRP

D221NRB 2 30A #14-8AWG 7.3” x 10.0” x 3.3” 6.0 $85.00D321NRB 3 30A #14-8AWG 7.3” x 10.0” x 3.3” 6.0 $119.00D222NRB 2 60A #12-2AWG 9.5” x 13.8” x 4.0” 11.0 $175.00D322NRB 3 60A #12-2AWG 9.5” x 13.8” x 4.0” 15.0 $199.00D223NRB 2 100A #10-1/0AWG 10.0” x 21.3” x 5.0” 17.0 $199.00


ELEC

TRIC

AL/

HARD

WAR

E

3/03

Electrical/SwitchgearFuses - Class RUL listed 125 VDC-250 VAC dual, element-time delay type fuse for use in general duty safetyswitches. 20,000 AIC interrupt rating.

Model Rated Current Dimensions MSRP

FRNR-20 20 A 0.56” diam. x 2.0” $7.75FRNR-30 30 A 0.56” diam. x 2.0” $7.75FRNR-40 40 A 0.81” diam. x 3.0” $13.90FRNR-50 50 A 0.81” diam. x 3.0” $13.90FRNR-60 60 A 0.81” diam. x 3.0” $13.90FRNR-80 80 A 1.06” diam. x 5.88” $31.00FRNR-100 100 A 1.06” diam. x 5.88” $31.00

Fuse Reducer - Class RFuse reducers allow smaller current rated fuses to be placed into the next larger current ratedenclosures, to increase space and lug size for larger wiring needs.


263-R Up to 30A into 60A space $19.00216-R From 35A to 60A into 100A space $27.00

Safety Switches- 600V Heavy-Duty Heavy-duty safety disconnect switches are offered fusible and non-fusible, indoor or outdoorwith external lockable switch handle. Service disconnect for AC or DC systems rated to 600volts. Wire lugs rated #14-6AWG. UL listed.

Model # Poles NEMA Rated Current Fusible Dimensions Weight (lbs) MSRP

H361 3 1 (indoor) 30A Yes 14.25” x 6” x 4.6” 10 $249.00 HU361 3 1 30A No 14.25” x 6” x 4.6” 10 $135.00H361RB 3 3R(outdoor) 30A Yes 15.25” x 6.5” x 4.75” 10 $459.00HU361RB 3 3R 30A No 15.25” x 6.5” x 4.75” 10 $249.00

Fuses- High Voltage AC/DCFor use with heavy duty fusible safety switches, 13/16” diameter x 5”.

Model Current Rating Max DC Voltage Dimensions MSRP

TRS12R 12A 600 5” x 13/16” $19.00A6Y15 15A 500 5” x 13/16” $29.00

AC Bypass Breaker Enclosure AssemblyUL listed, 120/240 VAC three-phase, main lug load centers can be used for distribution of ACgenerator power to bypass an AC inverter output circuit to household loads as a backup. Fullyassembled - includes solid neutral, main lugs, mechanical breaker interlock, and type ‘QO’ circuitbreakers. Indoor enclosure and cover.

Model # Spaces Current Rating Dimensions Weight (lbs) MSRP

BPB-60 3 60 A 5.9” x 13.1” x 3.4” 7.0 $199.00BPB-30 3 30 A 5.9” x 13.1” x 3.4” 7.0 $199.00

Class R Fuse

600V AC/DC Fuse

600V Safety Switch

AC Bypass Breaker Enclosure


ELECTRICAL/HARDW

ARE

3/03 73

Electrical/SwitchgearXANTREX DC Disconnects and Accessories The DC rated circuit breaker/disconnect with indoor enclosure ensures your installation’scompliance with NEC and other safety standard requirements. Designed to work specifically withSW and DR Series inverters and most solar charge controllers for residential and commercialapplications. Optional second inverter breaker, grounding/bonding block and circuit breakerallow field customization. ETL listed.


DC250 250 amp breaker with enclosure - for SW4024, SW5548,DR3624, DR2412 $329.00

DC175 175 amp breaker with enclosure - for SW4048, PS 2524,DR1512, DR1524, DR2424 $329.00

GJ250 Additional 250A breaker (field installable) for a second,stacked or unstacked SW or DR inverter $195.00

GJ175 Additional 175A breaker (field installable) for a second,stacked or unstacked SW or DR inverter $195.00

DCBB Negative/ground bonding block - connects up to two #4/0 AWG negative cables and ground system cables $50.00

CD60DC 60A circuit breaker for solar array input disconnect for C40/C60 – mounts on side of DC250/175 $39.00

CD15 15A circuit breaker for small DC load - mounts on side knockout of DC disconnect enclosure $29.00

CD20 20A circuit breaker for small DC load - mounts on side knockout of DC disconnect enclosure $29.00

Xantrex DC250 Disconnect

Electrical/Wire & CableTHHN/THWNGeneral purpose wiring, suitable for lighting and power in new or existing construction in residential, commercial and industrialsystems. Also used for power control circuits and relay panels. Single conductor, 19-strand copper with PVC insulationsheathed with nylon for easy pulling in conduits. Resistant to chemicals, oils, gasoline and flame. Rated 600 volts, 90˚C wet,75˚C dry. Sold by the foot.

AWG / Color O.D. Weight (lbs/1000ft) Ampacity (75˚C) MSRP#12THHN Red 0.14” 25 25A $0.17 per ft.#12THHN Black 0.14” 25 25A $0.17 per ft.#12THHN White 0.14” 25 25A $0.17 per ft.#12THHN Green 0.14” 25 25A $0.17 per ft.#10THHN Red 0.17” 39 35A $0.17 per ft.#10THHN Black 0.17” 39 35A $0.17 per ft.#10THHN White 0.17” 39 35A $0.17 per ft.#10THHN Green 0.17” 39 35A $0.17 per ft.#6THHN Red 0.25” 98 65A $0.50 per ft.#6THHN Black 0.25” 98 65A $0.50 per ft.#6THHN White 0.25” 98 65A $0.50 per ft.#6THHN Green 0.25” 98 65A $0.50 per ft.#4THHN Red 0.36” 115 85A $0.70 per ft.#4THHN Black 0.36” 115 85A $0.70 per ft.#4THHN White 0.36” 115 85A $0.70 per ft.


ELECTRICAL/HARDW

ARE

3/03


Fuses – Blade Type ATO/ATC Automotive standard 1/4” blade fuses for use in marine, RV and other systems with 12/24V DCcircuits (32V max).

Model Current Rating Color MSRP

ATO-1 1A black $0.30ATO-3 3A violet $0.30ATO-5 5A tan $0.30ATO-7.5 7.5A brown $0.30 ATO-10 10A red $0.30 ATO-15 15A lt. blue $0.35ATO-20 20A yellow $0.35ATO-25 25A natural $0.50 ATO-30 30A lt. Green $0.50

‘SEA’ Fuse Block System The most economical system for 100-300 ampere fusing for use with 12/24V DC systems.Features red glass filled nylon base with 5/16” non-ferrous studs supplied with two protectiveterminal boots for wiring up to #2/0 AWG.

Model Dimensions Weight (lbs) MSRP

5001 1.25” x 4.0” 0.29 $20.00

‘SEA’ Fuses – For 12/24 VDC systems. Interrupt capacity 2000 Amps.

Model Current Rating Dimensions Weight MSRP

5103 150A 0.75” X 2.70” 0.06 lbs $9.005105 200A 0.75” X 2.70” 0.06 lbs $9.005107 250A 0.75” X 2.70” 0.06 lbs $9.005108 300A 0.75” X 2.70” 0.06 lbs $9.00

Powerhouse Fuse Blocks – Class TPowerhouse inverter fuse blocks provide safe and reliable overcurrent protection for DC loadsconnected to battery systems of 12, 24 or 48VDC. This ‘one size fits all’ fuse block holds Class Tfuses (sold separately) from 100 to 400 amps and includes heavy-duty set screw lugs for up to#4/0 cable with a removable protective cover.


PH-FB 6.4” x 1.7” x 3.1” 0.4 $35.00

Class T Fuses For use on Powerhouse fuse blocks, rated 160VDC max. UL rated for DC service. Fast short-circuit response.

Model Size Dimensions Weight (lbs) MSRP

5112 110A 1.06” x 2.44” 0.19 $18.005116 200A 1.06” x 2.44” 0.19 $18.005119 300A 1.31” x 2.75” 0.29 $39.005121 400A 1.31” x 2.75” 0.29 $39.00

‘SEA’ Fuse Block

‘SEA’ Fuses

Powerhouse Fuse Blocks

Class T Fuse

Blade Type Fuse



ELEC

TRIC

AL/

HARD

WAR

E

3/03


Surge CapacitorsSurge capacitors help prevent damage to sensitive AC electrical equipment by controlling highvoltage surges too light or fast for a surge arrestor. They react continually with a slight voltageincrease and no delay. Includes 18” long-#12/2 wires.

Model Rated Voltage Dimensions MSRP

AC Capacitor 125/250 VAC 2.25” diam. x 4.5” $55.00

Lightning Arrestor shown withtop mount bracket (l) and sidemount bracket (r).

Lightning ArrestorsSilicon Oxide Varistor (SOV) lightning surge arrestors can handle high current surges that are toolarge for an MOV or capacitor. They provide protection to electrical equipment by reducingproblems due to lightning strikes or power surges. Surge arrestors react in as little as fivenanoseconds and begin to conduct when voltage rises above the nominal line voltage after aspecific time delay and handle an unlimited number of surges. The waterproof case is designedto install into a 1/2” knockout opening. Includes 18” long #12AWG wires. UL listed.

Model MSRPSide Mount $3.00Top Mount $9.00

Arrestor Mounting Bracket

Model Description Rated Voltage Dimensions Weight MSRP

LA302DC DC Arrestor up to 250VDC 2.25” diam. x 2.25” 1.0 $35.00LA602DC DC Arrestor up to 600VDC 2.25” diam. x 4.50” 1.5 $39.00LA302R AC Arrestor up to 300VAC 2.25” diam. x 2.25” 1.0 $35.00

Fuse Block System - ATO/ATC This fuse block system features a stylish, clear insulating cover that protects conductive partsand includes label recess for marking. Tin-plated copper buses allow 30 amp fuse rating percircuit, 100A max rating per block. Two styles -6 circuit with/without NEG bus, less fuses.

Model Description Dimensions MSRP

5025 6 circuit W/ Neg. bus 2.0” x 6.0” $27.005028 6 circuit 2.0” x 4.0” $24.00

Fuse Holder – In Line , ATO/ATCFor direct in line wiring for one type ATO/ATC fuse holder rated 30A max, with 4” #12AWG lead wires.


46021 Fuse Holder $2.50 46019 Fuse Cover Clear $1.25

Fuse Holder – Water Resistant ATO/ATC Sealed, weather resistant body and cap with mounting tab for one type ATO/ATC fuse, rated 30amp max. with 8” x #12AWG lead wires.


46033 Water Resistant Fuse Holder $5.00

5025 Fuse Block

In Line Fuse Holder

Water Resistant Fuse Holder

ELEC

TRIC

AL/

HARD

WAR

E

70 3/03


Toggle Circuit Breakers-AC/DC Toggle circuit breakers combine switching and circuit protection needs for 12/24/48 VDCsystems. Typically used for DC charge or load circuits rated 65 VDC/277V AC max. All are singlepole magnetic action in a phenolic case with screw terminals Compact size allows for less areaconsumed on DC panel assemblies 0.75” x 2”, toggle is red color. UL, CE recognized.

Model Current Rating Weight (lbs) MSRP

7205 10A 0.17 $17.007209 15A 0.17 $17.007213 20A 0.17 $17.007221 30A 0.17 $17.007225 40A 0.17 $17.007229 50A 0.17 $17.00

Mounting Panel – Toggle BreakersAttractive dark aluminum 1/8” panels hold one or two toggle type breakers or panel switches.


8072 for one breaker 2.63” x 3.75” 0.08 $17.008173 for two breakers 2.63” x 3.75” 0.08 $21.008035 circuit breaker screws (6 pk) – flat head, black to match panel $2.25

Digital Multi-Meter – 5 DC Circuit Breaker Panel AssemblyThis DC digital multi-meter displays voltage to 60 VDC and amperes to 500A. Includes shunt,high and low voltage alarms, and a 3 position switch for multiple battery banks, positive andnegative and ground buses, five - 15 amp, 65VDC circuit breakers are pre-wired for loaddistribution with 30 common DC load labels. Gray powder coated 1/8” aluminum panel.


8401 7.50” x 5.25” 3.45 $359.00

DC Ammeter – AnalogUseful for measuring current flow from PV or wind sources to battery-draws 1ma. Accuracy 3%,2-3/4” face-flush mount, simple 2-wire connection from shunt.

Model Scale Dimensions Weight (lbs) MSRP

8005 25A 2.8” x 2.4” 0.24 $37.00

DC Voltmeter – AnalogMeter with 2-3/4” face-flush mount, 3% accuracy, simple 2-wire connections, draws 1ma.

Model Voltage Scale Dimensions Weight (lbs) MSRP

8003 8-16V DC 2.8” x 2.4” 0.23 $33.008240 18-32V V DC 2.8” x 2.4” 0.23 $42.00

AC/DC Circuit Breakers

Toggle Breaker Mounting Panel

DC Analog Ammeter

Digital Multi Meter Assembly

DC Analog Voltmeter



Batteries

BATT

ERIE

S

3/03

Concorde Sun-Xtender Battery

Concorde – Sun-Xtender VRLA-AGMSun-Xtender batteries are absorbed glass matt (AGM) sealed, maintenance free, valve-regulated,lead-calcium alloy batteries designed for deep-cycle PV applications. These batteries featureimmobilized, non-spillable electrolyte in AGM microporous sun glass separators. The T series featurecopper alloy M8 terminals except on the PVX 340T & 420T which are M6. The L series featureheavy-duty “L” blade terminals. Both are designed for heavy duty, high current capacities. Sun-Xtenders have a wide range of operating temperatures from -40ºF (-40ºC) to 160ºF (72ºC) as well aslow self-discharge of approximately 1% per month at 77ºF (25ºC). All include 5/16” silicon bronzebolts for connection except the PVX340T and 420T which include 1/4” bolts. “Non-spillablebatteries” for transport-complies with DOT HMR49 Non-hazardous materials. UL recognized systemcomponent. Limited two-year warranty. Battery racks available, call for information.

Full charge termination voltage (@ 25C) = 14.40vDC, float charge at 13.4vDC Temperature compensation +/- 3.75mv per cell/C degrees @ 25C, from (0C to 40C)

Concorde

Storing Energy in Batteries

For systems requiring electrical energy storage for use when the sun is not shining, batteries are the answer. They are alsoknown as “accumulators” in other parts of the world, which is a very accurate name since their function is to accumulate or storeelectrons produced by solar modules. You won’t need batteries for grid-tie only systems where excess energy is fed into theelectric grid via the utility company or water pumping systems where energy is stored in the form of water pumped during theday and used at night. Typically, batteries are used in locations where grid power is not available or practical or for grid-tiesystems that double as home backup power systems. The battery-based, stand-alone (no other source of power) PV system has many practical uses such as radio transmitters, recreational vehicles and boats, park lighting, and remote home power.Stand-alone PV systems need a battery bank large enough to sustain the load for a period of time without being recharged.

There are two battery types used most often in PV applications: Valve Regulated Lead Acid (VRLA) and Flooded Lead Acid (FLA).VRLA technology includes gelled electrolyte and absorbed glass mat (AGM) batteries. All batteries in this catalog are rated fordeep-cycle applications. PV systems should not use batteries designed to start engines.

VRLA batteries are maintenance-free, non-spillable, and have a superior shelf life. A ‘gel’ battery is a VRLA storage battery that issealed using special pressure valves and should never be opened. An AGM battery offers the same features except the electrolyteis absorbed in separators of matted glass fibers and it provides better performance. Gel and AGM batteries are less susceptible tofreezing than FLA batteries. They also carry non-hazardous classifications and can be mounted in other positions beside horizontal.

FLA batteries are better for larger applications, such as remote homes, where greater currents are required. They offer the lowestinstalled cost if the location is accessible in order to water the battery periodically. FLA batteries take more punishment than gelor AGM types, however, are not suited for sites that are difficult to access or freezing climates. FLA batteries must be vented,can cause corrosion when near sensitive electronics and ship via truck freight.

There is a balance between battery life and the size of the battery bank. We recommend you consult with your dealer.

Expected life cycles versusdepth of discharge (DOD) @ 1-hour rate/25ºC (77ºF):

• 5200 @ 10% DOD• 1850 @ 30% DOD• 1050 @ 50% DOD

NEW Model OLD Model AH Capacity UnitNumber Number Voltage @ C/120 Dimensions Weight (lbs) MSRP

PVX-340T (PVX-1234T) 12 V 38 7.71” x 5.18” x 6.89” 25 $83.00PVX-420T (PVX-1240T) 12 V 45 7.71” x 5.18” x 8.46” 30 $106.00PVX-490T (PVX-1248T) 12 V 55 8.99 x 5.45 x 8.82 31 $116.00PVX-560T (PVX-1255T) 12 V 63 8.99 x 5.45 x 8.82 36 $124.00PVX-690T (PVX-1265T) 12 V 79 10.22 x 6.60 x 8.93 51 $155.00PVX-890T (PVX1285T) 12 V 102 12.90” x 6.75” x 8.96” 62 $189.00PVX-1040T (PVX-12100T) 12 V 120 12.00” x 6.77” x 8.93” 66 $202.00PVX-1080T (PVX-12105T) 12 V 126 12.90” x 6.75” x 8.96” 69 $211.00PVX-2120L* (PVX-12210L) 12 V 253 20.75” x 8.71” x 10.66” 138 $413.00PVX-2580L* (PVX-12255L) 12 V 305 20.72” x 10.94” x 10.23” 165 $489.00

* rope handles

BATTERIES

3/03

Batteries

VRLA- Gel The Deka Solar/MK Battery series of valve-regulated, gelled-electrolyte batteries is designed tooffer reliable, maintenance-free power for renewable energy applications where frequent deepcycles are required and minimum maintenance is desirable. The sealed construction eliminatesperiodic watering, corrosive acid fumes and spills. The electrolyte will not stratify so noequalization charging is required. Less than 2% per month standing loss means little deteriorationduring transport and storage. They are ideal for small to medium sized PV systems and are ratednon-spillable by ICAO, IATA and DOT. These batteries feature-polypropylene containers with selfsealing vents, lead-calcium plate alloy within sulfuric acid thixotropic gel. Batteries do not includeterminal bolts-all use 5/16”-18 x 1”(except for 8GU1 = 1/4”-20 x 1”) sold separately. Five-yearlimited warranty - free replacement on the first two years and pro-rated on the last three years ofthe warranty.

MK Battery

Deka Solar/MK Battery

Expected life cycles versusdepth of discharge (DOD) @ 20-hour rate + 20ºC :

• 3800 @ 10% DOD• 1500 @ 30% DOD• 650 @ 50% DOD

Model Voltage Capacity @ Bolt Dimensions Weight MSRP100 Hr. Rate Size L x W x H (lbs)

8GUI 12V 36 Ah 1/4” 7.75” x 5.13” x 7.25” 24 $97.008G22NF 12V 58 Ah 11/32” 9.40” x 5.50” x 9.25” 39 $147.008G24 12V 84 Ah 5/16” stud 10.88” x 6.75” x 9.88” 54 $193.008G27 12V 99 Ah 5/16” stud 12.75” x 6.75” x 9.88” 64 $219.008G31 12V 112 Ah 3/8” 12.90” x 6.75” x 9.40” 74 $255.008G4D 12V 210 Ah 3/8” 20.75” x 8.50” x 10.00” 131 $469.008G8D 12V 265 Ah 3/8” 20.75” x 11.0” x 10.00” 161 $561.008GGC2 6V 198 Ah 11/32” 10.25” x 7.13” x 10.88” 68 $255.00

VRLA–AGM MK Battery

VRLA–AGM Sealed, maintenance-free, valve-regulated type AGM batteries are available in smaller sizecapacity ratings, perfect for use with solar applications for powering lighter loads such astelemetry, SCADA, remote monitoring, UPS systems, LED and emergency lighting. Capacitydischarge ratings are at the 20-hour rate- 20ºC at -4ºF to 122ºF. Charge termination voltage-cyclic use = 14.40 VDC, float 13.80Vdc. Rated Non-Spillable-DOT. Two-year limited warranty.

Model Voltage Capacity @ Bolt Dimensions Weight MSRP100 Hr. Rate Size L x W x H (lbs)

ES 712 12 7 0.187” tab 5.95” x 2.56” x 3.70” 6 $24.00ES1212 12 12 0.187” tab 5.95” x 3.86” x 3.70” 9 $39.00ES1712 12 17 0.50” flag 7.13” x 2.99” x 6.58” 14 $49.00

Whether your application requires extended cycle life, long duration at low rates ofdischarge, minimal recharge time, or maximum high-rate performance, MK Batterymanufactures and distributes only the highest quality batteries available anywhere.Not only do we continually test our own batteries; we carefully evaluate othermanufacturers products as well. Moreover, we assess their overall capabilities aspotential suppliers to assure that we are delivering to you the most effectivetechnology for your unique requirements. "A battery is just a battery" does notapply here.


Batteries

BATT

ERIE

S

34 3/03

Rolls 4000 Series

Rolls 4000 and 5000 SeriesThe Rolls Battery flooded, deep-cycle line features extended standard warranties and doubleinsulated-enveloped positive plates that eliminate the possibility of separator misalignment,cracked separators, treeing or shorting at the bottom or sides. Each battery cell has increasedliquid reserve levels, resulting in fewer watering intervals. The rugged plate construction allowsfor a long cycling service - the 4000 series for a 10-year average life and the 5000 series for 15years. The 5000 series are constructed in a dual container. Each 2-volt cell is assembled in itsown inner polypropylene container within a moisture tight, protective outer container eliminatingshort circuits due to water or falling metal objects. Series 4000 batteries carry a 24-month freereplacement warranty (FOB factory) and include an 84-month adjustment period from date ofinstallation. Series 5000 batteries carry a 36-month free replacement warranty (FOB factory) andinclude a 120-month adjustment period from date of installation (USA only). Freight allowanceEast of the Mississippi on 1000 lb. minimum orders, West of Mississippi on 2000 lb. minimumorders. Are available dry charged. Bolt size is 5/16”.

Rolls Battery Engineering

4000 series expected lifecycles vs depth of discharge,@ 20 hr rate, +25ºC:

• 2240 @ 10% DOD• 1707 @ 30% DOD• 1280 @ 50% DOD


• 5500 @ 10% DOD• 4200 @ 30% DOD• 3200 @ 50% DOD

Capacity @ Dimensions Wet Weight Dry Weight Model Voltage 100 Hr. Rate L x W x H (lbs) (lbs) MSRP

4000 SeriesS-460 6 V 460 Ah 12.28” x 7.13” x 16.75” 129 90 $265.00

S-530 6 V 530 Ah 12.28” x 7.13” x16.75” 140 115 $295.00

5000 Series4-CS-17PS 4 V 770 Ah 14.38” x 8.25” x 18.25” 128 98 $425.00

4-KS-21PS 4 V 1557 Ah 15.75” x 9.75” x 24.75” 230 186 $860.00

4-KS-25PS 4 V 1900 Ah 15.75” x 10.63” x 24.75” 315 220 $1,075.00

6-CS-17PS 6 V 770 Ah 22” x 8.25” x 18.25” 221 178 $635.00

6-CS-21PS 6 V 963 Ah 22” x 9.75” x 18.25” 271 217 $795.00

6-CS-25PS 6 V 1156 Ah 22” x 11.25” x 18.25” 318 254 $960.00

8-CS-25PS 8V 1156 Ah 28.25 X 11.25 X 18.25 492 342 $1,275.00

Model Voltage Capacity @ Dimensions Weight MSRP100 Hr. Rate L x W x H (lbs)

85N-17 2 V 1020 Ah 6.62” x 6.5” x 24” 128 $445.0085N-25 2 V 1530 Ah 6.62” x 9.5” x 24” 184 $570.0085N-33 2 V 2040 Ah 6.62” x x 12.5” x 24” 242 $750.00

IBE flooded lead-antimony batteries feature flag type terminals on positive and negative postsfor easy connection. Heat sealed cell covers eliminate electrolyte leakage reducing corrosionbuild-up. A sealing compound around the edge of the case and cell reduces the problem ofelectrolyte corrosion at the edge of the steel case. The cell is a high-capacity industrial type fordeep cycle operation - 5000 cycles @ 20% DOD. Lifting handles are provided. Eight-year limitedwarranty - 5-year full and 3-year prorated. Price includes standard steel case with handles. Drycharge models available. Discounts available for 3 and 6 cell cases. 3/8”-16 X 1” battery boltssold separately

IBE 85N Battery

Industrial Battery Engineering



Batteries

BATT

ERIE

S

3/03

Rolls 4000 Series

Rolls 4000 and 5000 SeriesThe Rolls Battery flooded, deep-cycle line features extended standard warranties and doubleinsulated-enveloped positive plates that eliminate the possibility of separator misalignment,cracked separators, treeing or shorting at the bottom or sides. Each battery cell has increasedliquid reserve levels, resulting in fewer watering intervals. The rugged plate construction allowsfor a long cycling service - the 4000 series for a 10-year average life and the 5000 series for 15years. The 5000 series are constructed in a dual container. Each 2-volt cell is assembled in itsown inner polypropylene container within a moisture tight, protective outer container eliminatingshort circuits due to water or falling metal objects. Series 4000 batteries carry a 24-month freereplacement warranty (FOB factory) and include an 84-month adjustment period from date ofinstallation. Series 5000 batteries carry a 36-month free replacement warranty (FOB factory) andinclude a 120-month adjustment period from date of installation (USA only). Freight allowanceEast of the Mississippi on 1000 lb. minimum orders, West of Mississippi on 2000 lb. minimumorders. Are available dry charged. Bolt size is 5/16”.

Rolls Battery Engineering


• 2240 @ 10% DOD• 1707 @ 30% DOD• 1280 @ 50% DOD


• 5500 @ 10% DOD• 4200 @ 30% DOD• 3200 @ 50% DOD

Capacity @ Dimensions Wet Weight Dry Weight Model Voltage 100 Hr. Rate L x W x H (lbs) (lbs) MSRP

4000 SeriesS-460 6 V 460 Ah 12.28” x 7.13” x 16.75” 129 90 $265.00

S-530 6 V 530 Ah 12.28” x 7.13” x16.75” 140 115 $295.00

5000 Series4-CS-17PS 4 V 770 Ah 14.38” x 8.25” x 18.25” 128 98 $425.00

4-KS-21PS 4 V 1557 Ah 15.75” x 9.75” x 24.75” 230 186 $860.00

4-KS-25PS 4 V 1900 Ah 15.75” x 10.63” x 24.75” 315 220 $1,075.00

6-CS-17PS 6 V 770 Ah 22” x 8.25” x 18.25” 221 178 $635.00

6-CS-21PS 6 V 963 Ah 22” x 9.75” x 18.25” 271 217 $795.00

6-CS-25PS 6 V 1156 Ah 22” x 11.25” x 18.25” 318 254 $960.00

8-CS-25PS 8V 1156 Ah 28.25 X 11.25 X 18.25 492 342 $1,275.00

Model Voltage Capacity @ Dimensions Weight MSRP100 Hr. Rate L x W x H (lbs)

85N-17 2 V 1020 Ah 6.62” x 6.5” x 24” 128 $445.0085N-25 2 V 1530 Ah 6.62” x 9.5” x 24” 184 $570.0085N-33 2 V 2040 Ah 6.62” x x 12.5” x 24” 242 $750.00

IBE flooded lead-antimony batteries feature flag type terminals on positive and negative postsfor easy connection. Heat sealed cell covers eliminate electrolyte leakage reducing corrosionbuild-up. A sealing compound around the edge of the case and cell reduces the problem ofelectrolyte corrosion at the edge of the steel case. The cell is a high-capacity industrial type fordeep cycle operation - 5000 cycles @ 20% DOD. Lifting handles are provided. Eight-year limitedwarranty - 5-year full and 3-year prorated. Price includes standard steel case with handles. Drycharge models available. Discounts available for 3 and 6 cell cases. 3/8”-16 X 1” battery boltssold separately

IBE 85N Battery

Industrial Battery Engineering

BATTERIES

3/03

Battery Accessories

Innovative Energy Systems

DS-1000

DeSulfator Advantages• conditions battery• increases battery life• increases battery

performance• increases equipment

reliability• decreases battery

replacement costs• two-year warranty

Model Battery Capacity Power Consumption Dimensions Weight MSRP

DS-500 Up to 350 Amp hours 0.2 watts 2” x 3” x 1.5” 0.4 lbs $115.00DC-1000 350-1000 Amp hours 0.4 watts 3” x 3” x 1.5” 0.6 lbs $169.00

Battery safety vent caps reduce the maintenance of constantly replenishing the water in floodedbatteries. Condensing pellets within the cap capture and return electrolyte droplets into each cellduring the charging to assure better electrolyte maintenance. A flip-top design allows easierwatering without needing to remove the cap.

Model MSRPWater Miser Vent Caps $7.50

Water Miser Vent Cap

Water Miser Vent Caps

DeSulfator Battery ConditionersWhen a lead-acid battery is discharged, a soft, lead sulfate material forms on the battery plates.During the battery’s recharge, this material is lifted off of the plates and recombined into thebattery’s electrolyte solution. If, however, the battery is left in a partial state of discharge for asshort as 70 hours, the lead sulfate material will begin to harden and crystallize, forming apermanent insulative barrier. As this barrier becomes thicker, the battery’s ability to accept acharge or deliver energy is diminished, resulting in the perception that the battery is no longerusable. The accumulation of such deposits, otherwise known as sulfation, is the most destructiveprocess in the life of any lead-acid battery.

The DeSulfator battery conditioner is a pulse generator that extends the life of lead-acid batteriesand increases their efficiency. Using its patented sweeping pulse process, the DeSulfatorelectronically eliminates and prevents this life limiting process. Batteries protected by theDeSulfator will provide more energy and last longer than any other battery. Designed to operatewithout taking the battery out of service, it connects directly to the battery. The DeSulfator emits a“sweeping pulse” of energy to the battery set. The frequency at which these pulses are emittedare tuned to excite the structural components of the sulfate deposits. This process enablessulfation to revert back into the electrolyte solution. Simply attach the color-coded leads to the battery terminals. Its smart multi-plexing circuitry uses onlya fraction of a watt to continually condition the battery. It does not interfere with any type of batterycharging equipment and works on all types of lead-acid batteries including wet cell, sealed, gel-cellor absorbed electrolyte. Specify voltage when ordering: 12, 24, or 48. 12” lead length.

Braun’s R&D, a subsidiary of Braun’s Energy Products, who provides independent testing andevaluation to manufacturers of industrial and maintenance products, reached the followingconclusions after testing the DS-500:

1. The sweeping pulse technology improves the performance of most batteries.2. The sweeping pulse technology did not have any “negative” effects. The operation of the IESdevices was transparent to the operators of all of the vehicles tested.3. The DS500 Battery Conditioner proved significantly beneficial for most batteries.4. The units were more beneficial to newer batteries over “seasoned” batteries.

We have used the term “most batteries” because the Sweeping Pulse Technology cannot restorea battery that has structural damage. During our field evaluation we encountered severalstructurally damaged batteries. It should be noted that several of the damaged batteries actuallyshowed improvements in several tested areas, just not enough to return them to service. Wedefined “performance” in terms of available amperage and load voltage, i.e., higher availableamperage and high load voltage values equals a “stronger” battery.

Although we did not directly measure reserve capacity and life span, we believe that thesweeping pulse technology devices will have a positive effect on these characteristics. We basethis statement on the fact that these characteristics are directly influenced by the performance wedid measure.

DS-500


BATT

ERIE

S

3/03

Battery Enclosures

SunWize Premium Enclosures

Hinged Cover Battery EnclosuresSunWize premium F-series hinged cover enclosures are engineered specifically for the PV industryallowing the installer to add controllers and other electrical components. Additional back, side anddoor panels are available. Designed for outdoor use, NEMA type 3R/12 construction, enclosureshave bottom-to-top rain and dust proof vent design. A removable front opening door is lined witha sealing gasket and includes a special keyed cam-lock and dust cover. These enclosures arewhite powder coated aluminum for ultimate protection in severe climates. For applications inextreme hot or cold conditions, space is available for additional 1” foam insulation around the battery.

Features: • 3 models for either 1, 2 or 4 batteries (125 Ah) • Vertical design on 4 battery enclosure (2 + 2) with removable interior shelf • Passive venting with dust filtration pads• 1/4 turn cam-locking door latches with special key and dust cover • Electrical knockouts andground lug hole on rear • Rear-top of enclosure ‘hanger’ built in for easy installation ontomounting brackets • Vandal resistant mounting brackets and U-bolt sets are sold separately

SunWize®

Model Dimensions DIM.A Weight MSRP

F1 - 1 battery 20.75” x 16.00” x 9.38” 12 7/8 25 lbs $335.00

F2 - 2 batteries 20.75” x 16.00” x 14.38” 12 7/8 30 lbs $379.00

F4 - 4 batteries 32.00” x 16.00” x 14.38” 24 1/8 40 lbs $499.00

Extra Door Key – #E3-5-15, Cylinder type $4.50

SunWize Economy Enclosures

Economy Battery EnclosuresAvailable in five sizes, E-series economy battery enclosures are cost-effective solutions for housing oneto four batteries. These enclosures feature aluminum screw covers, NEMA 3R type rainproof, ventedconstruction, and an attractive brushed grain finish with rear 1/2” electrical knockouts. They include aremovable back panel for mounting PV controls and other components (except E1-19 size). The twosmall enclosures, have two external mounting feet sized for 2” pipe U-bolt attachment. The three largeenclosures, for housing 1, 2 or 4 (up to 126 Ah) batteries, include a door lock-hasp and rear wall/polemounting bracket holes. Brackets sold separately. Extra space is provided in all to allow for 1” foaminsulation around the battery. Tamper proof door screws can be added for extra security.


E1-19 11.38 x 9.25 x 5.08 4.0 lbs $95.00E1-55 14.50 x 10.25 x 7.50 6.0 lbs $125.00E1-125 17.00 x 16.00 x 9.50 12.0 lbs $139.00E2-250 17.00 x 16.00 x 15.00 17.0 lbs $159.00E4-500 32.00 x 16.00 x 15.00 25.0 lbs $249.00

Top Opening Battery EnclosuresExterior white powder coated finish, T-series battery enclosures are designed for housing largergroup 4D (250 Ah) & 8D (300 Ah) batteries and will house many other battery sizes as well. Theseenclosures feature 0.125” aluminum, NEMA 3R type rainproof-vented construction and include 3” x 5” channel skids with pad anchoring holes to provide ground clearance for a fork lift. Thecontinuous ST-ST hinged cover includes a prop rod, lock hasp and 1/2” side conduit entries. Allhave interior mounting panel studs on sides and top cover for additional PV control & componentmounting - panels are sold separately. Extra space is allowed for 2” foam insulation around thebattery and under top cover - add ‘F’ suffix to model number for foam insulation installed.

SW Top Opening Enclosure Model Quantity x Battery Group Dimensions Weight MSRP

T-3X4D 3 x 4D or 2 x 8D 20.00” x 31.25” x 23.75” 55.0 lbs $595.00

T-6X4D 6 x 4D or 4 x 8D 20.00” x 48.25” x 30.25” 100.0 lbs $765.00

T-6X8D 8 x 4D or 6 x 8D 20.00” x 48.25” x 40.25” 125.0 lbs $995.00


BATTERIES

3/03

Premium Mounting Brackets - for wall/pole mounting, ideal for F-series enclosuresMatching white power coat finish aluminum channels are used forwall or pole mounting. Slotted pattern allows U-bolt sizes from 2”to 8” (schedule 40 pipe) or larger band clamps. Brackets are firstmounted in place on wall or pole. Enclosure is then hung in placeon top bracket and bolted through lower bracket to secure‘carriage-bolts’ for vandal resistance.

Economy Enclosure Mounting Brackets - for wall or pole mounting, ideal for E-series enclosuresSame specs as above except with matching brushed grain finish.


F-BKTSET(Premium) 2” sq. x 13” long 2.0 lbs $35.00E-BKTSET(Economy) 2” sq. x 13’ long 2.0 lbs $29.00

Battery Enclosures

SW Economy EnclosureMounting Brackets

SW Premium Mounting Brackets

SunWize®

Mounting Brackets - for concrete padAluminum strut channels are used in combination with captive lock nuts and supplied with 3/8”ST-ST fasteners for attachment to enclosure bottom - allows clearance for air flow, flood waterand door opening. Concrete anchors not furnished. Requires four bottom holes added byinstaller. Can be used with either F or E series enclosures.


PD-MTGBKTSET 1-5/8” sq. x 20” long 4.0 lbs $45.00

SW Pad Brackets

SW Enclosure Mounting Panels

Hinged Cover Enclosure Mounting PanelsAll F-series enclosures include interior studs for mounting of ‘Rear’ and ‘Right-Side’ back panels andan interior door panel. Back panels are made of 0.080” brushed aluminum with four mounting holes.Right-side and door panels are blank, rear panels are either blank or with 39 pre-located holes for #8self tapping screws, allowing simple attachment of most commonly used PV controllers, breakers,terminal strips, surge arrestors, and ballasts.


F-HC-RP-B Rear panel-blank 15.50 x 6.50 0.70 lbs $12.00F-HC-RP-D Rear panel-drilled 15.50 x 6.50 0.70 lbs $15.00F-HC-RSP-1B Right side (one battery) 8.75 x 3.75 0.23 lbs $9.00F-HC-RSP-2/4B Right side (2/4 battery) 9.50 x 6.25 0.41 lbs $10.00F-HC-DRP-2/4B Door panel 9.44 x 8.88 0.58 lbs $12.00

Top Opening Enclosure Mounting Panels Blank panels are 0.125” brushed aluminum with four mounting holes for side and top coverlocations to allow attachment of PV charge controllers and other components. Side panel ‘MP-S’ fits all chest sizes. Top panel ‘MP-T’ fits both 6 x 4D & 6 x 8D enclosures.


MP-S Side Panel 15.50” x 6.50” 0.70 lbs. $12.00MP-T3x4D Top Panel 24.00” x 13.00” 3.50 lbs. $59.00MP-T Top Panel 24.00” x 24.00” 7.00 lbs. $99.00

Enclosure w/Mounting Panels


BATT

ERIE

S

3/03

AWG Length Color Weight (lbs) MSRP

4 8” black 0.4 $6.904 8” red 0.4 $6.904 13” black 0.5 $7.804 13” red 0.5 $7.804 16” black 0.6 $8.904 16” red 0.6 $8.904 24” black 0.8 $10.254 24” red 0.8 $10.25

2/0 8” black 0.6 $11.602/0 8” red 0.6 $11.60 2/0 13” black 0.7 $13.402/0 13” red 0.7 $13.402/0 16” black 0.8 $14.502/0 16” red 0.8 $14.502/0 24” black 1.3 $17.252/0 24” red 1.3 $17.252/0 36” black 1.6 $24.502/0 36” red 1.6 $24.50

AWG Length Color Weight (lbs) MSRP

2/0 48” black 2.2 $31.202/0 48” red 2.2 $31.202/0 60” black 2.7 $36.752/0 60” red 2.7 $36.75

4/0 8” black 0.8 $14.504/0 8” red 0.8 $14.504/0 13” black 1.1 $16.754/0 13” red 1.1 $16.754/0 18” black 1.3 $20.504/0 18” red 1.3 $20.504/0 24” black 1.7 $24.504/0 24” red 1.7 $24.504/0 36” black 2.4 $33.504/0 36” red 2.4 $33.504/0 48” black 3.1 $41.754/0 48” red 3.1 $41.754/0 60” black 3.9 $51.254/0 60” red 3.9 $51.25

Battery Terminal Hardware KitsSunWize battery hardware kits are necessary for connecting cabling to battery flag terminals. Kitscontain two bolt sets of high quality, stainless steel to eliminate corrosion. Each bolt set consists of ahex head screw, flat washers, lock-washer and hex nut.

Model MSRP1/4-20 x 1” $1.355/16-18 x 1” $1.753/8”-16 x 1” $2.00

Battery Cables

SW Battery Hardware Kit

SunWize®

Battery CablesSunWize high quality battery interconnect cables are the best value available featuring xtra-flex,multi-stranded copper cable - rated 105˚C degrees, 600 volt, (UL) type MTW/THW, CSA -TEW.All cables are assembled with large, tin-plated copper lugs for 3/8” bolts, double crimped andheat sealed with color coded melt wall tubing, ensuring long life. Maximum conductor ampacityin free air: 4AWG=120A, 2/0=265A, 4/0=360A. Other lengths available.

SW Inverter to Battery Cables

Inverter to Battery CablesPre-cut and crimped, UL rated cables reduce system installation time, improve system integrityand assure code compliance. These flexible cables are made with ring terminals and color-codedheatshrink. NEC rated in conduit for 230 amp (#4/0 AWG). 175 amp (#2/0 AWG) and in free airfor 360 amp (#4/0 AWG) or 265 amp (#2/0 AWG). Cables sold as pairs.


IBC10-2/0 10 feet, red and black heatshrink $118.00IBC10-4/0 10 feet, red and black heatshrink $145.00IBC15-2/0 15 feet, red and black heatshrink $154.00IBC15-4/0 15 feet, red and black heatshrink $205.00

SW Battery Cables


OutBack Power System RackThe Power System Rack is a combined battery cabinet and system component rack. It combinesbattery disconnects, overcurrent protection devices and the inverter/chargers into a single enclosure.ETL listed. For indoor use only.


PSR Power System Rack. Includes removable top & side panels, two shelves and conduit/breaker knockout plates. PSR front bracket will hold one DC-GFP/2,two PV array disconnect breakers and one large inverter/battery breaker.Holds eight non-sealed T105 or 4 L-16 batteries. Ships in 3 boxes. $649.00

PSR-FO Power System Rack – Frame only. Same as the standard PSR except withoutenclosure panels or conduit/breaker brackets. Comes standard with three shelves. Ships in 2 boxes. Holds 12 non-sealed T105s or 8 non-sealedL-16 batteries. Not ETL listed. $399.00

Accessories

PSR-3RK Type 3R/Outdoor Rainproof Kit – allows mounting of the PSR outdoors.Includes insulated powder coated aluminum rainshield, gasketing and lockable,transparent flip up circuit breaker cover. ETL listed. $149.00

PSR-BCK Transparent flip up circuit breaker cover w/mounting screws & padlock hasp. $19.00

PSR-HDT Heavy Duty Top – allows mounting of an SW series inverter/charger with conduit box on top of the PSR cabinet. $79.00

PSR-MP Mounting Plate – attaches to the back of any PSR version to allow mounting of electrical components. Predrilled for TBB and GBB options and various other control/inverter components - fits inside of enclosure panel. $39.00

PSR-SCT Spill Containment Tray – Holds four Group 31, T105 or L16 batteries - fits on one PSR shelf - molded polyethylene. $29.00

PSR-SK Shelf Kit – adds another shelf to the PSR for more batteries or inverter/charger when using sealed batteries. $89.00

PSR-SZ4 Seismic Zone 4 kit – includes two mounting feet and battery restraint straps for up to 12 batteries. $89.00

BATTERIES

3/03 39

Battery Racks

OutBack PSR Battery Rack

OutBack Power

Battery Chargers

SEC Battery ChargersSamlex automatic battery chargers are ideal for communication sites, battery backup systems,RV and marine applications. They feature advanced switch-mode design, 3 stage charging,reverse polarity connection protection and fully automatic operation.

Samlex

Samlex SEC-2415A

Model Output Voltage Input Voltage Max. Charging Current Dimensions Weight MSRP

SEC-2415A 24 VDC 120 VAC 15 A 10.7” x 8.4” x 3.3” 5.3 lbs $350.00

SEC-2425A 24 VDC 120 VAC 25 A 12” x 9” x 4” 11.1 lbs $530.00

OutBack PSR-FO Battery Rack



OutBack Power System RackThe Power System Rack is a combined battery cabinet and system component rack. It combinesbattery disconnects, overcurrent protection devices and the inverter/chargers into a single enclosure.ETL listed. For indoor use only.


PSR Power System Rack. Includes removable top & side panels, two shelves and conduit/breaker knockout plates. PSR front bracket will hold one DC-GFP/2,two PV array disconnect breakers and one large inverter/battery breaker.Holds eight non-sealed T105 or 4 L-16 batteries. Ships in 3 boxes. $649.00

PSR-FO Power System Rack – Frame only. Same as the standard PSR except withoutenclosure panels or conduit/breaker brackets. Comes standard with three shelves. Ships in 2 boxes. Holds 12 non-sealed T105s or 8 non-sealedL-16 batteries. Not ETL listed. $399.00

Accessories

PSR-3RK Type 3R/Outdoor Rainproof Kit – allows mounting of the PSR outdoors.Includes insulated powder coated aluminum rainshield, gasketing and lockable,transparent flip up circuit breaker cover. ETL listed. $149.00

PSR-BCK Transparent flip up circuit breaker cover w/mounting screws & padlock hasp. $19.00

PSR-HDT Heavy Duty Top – allows mounting of an SW series inverter/charger with conduit box on top of the PSR cabinet. $79.00

PSR-MP Mounting Plate – attaches to the back of any PSR version to allow mounting of electrical components. Predrilled for TBB and GBB options and various other control/inverter components - fits inside of enclosure panel. $39.00

PSR-SCT Spill Containment Tray – Holds four Group 31, T105 or L16 batteries - fits on one PSR shelf - molded polyethylene. $29.00

PSR-SK Shelf Kit – adds another shelf to the PSR for more batteries or inverter/charger when using sealed batteries. $89.00

PSR-SZ4 Seismic Zone 4 kit – includes two mounting feet and battery restraint straps for up to 12 batteries. $89.00

BATTERIES

3/03

Battery Racks

OutBack PSR Battery Rack

OutBack Power

Battery Chargers

SEC Battery ChargersSamlex automatic battery chargers are ideal for communication sites, battery backup systems,RV and marine applications. They feature advanced switch-mode design, 3 stage charging,reverse polarity connection protection and fully automatic operation.

Samlex

Samlex SEC-2415A

Model Output Voltage Input Voltage Max. Charging Current Dimensions Weight MSRP

SEC-2415A 24 VDC 120 VAC 15 A 10.7” x 8.4” x 3.3” 5.3 lbs $350.00

SEC-2425A 24 VDC 120 VAC 25 A 12” x 9” x 4” 11.1 lbs $530.00

OutBack PSR-FO Battery Rack

Battery Chargers

DLS SeriesThe DLS Series Charger/Power Supply uses switch-mode technology to insure service freeoperation even when subjected to extremely harsh conditions. The clean DC output operatesradios and televisions without causing annoying static or snow. Pumps, motors, lights and fansoperate perfectly for prolonged life. They feature regulated converter/power supply, tight line-loadregulation, two-step voltage switch, current limiting, transient voltage protection and shortcircuit/over-current protection. The DLS maintains the batteries, only putting into the battery whatis required by load or self-discharge, cutting back to milliamps as the battery requires. All modelsinclude cooling fan. Charger efficiency approx. 85%. Two-year warranty.

Iota Engineering Company

Iota DLS 55

BATT

ERIE

S

40 3/03

Model

Truecharge 10 – 1 bank clip leadTruecharge 10TB – 2 bank hardwireTruecharge 20+ – 3 bankTruecharge 40+ – 4 bankACCESSORIESDisplay Panel - True Charge 20+Display Panel - True Charge 40+Temperature Sensor - True Charge 20/40

MSRP

$200.00$160.00$340.00$450.00

$40.00$40.00$30.00

OutputVoltage

13.8/14.8 VDC14.2/14.4 VDC13.8/14.8 VDC13.8/14.8 VDC

Dimensions LxWxH

9.0” x 6.5” x 2.75”10.65“ x 6.5” x 2.75”15.0“ x 6.5” x 2.75”15.0” x 6.5” x 2.75”

Weight(lbs)

3.03.05.57.5

InputVoltage

120VAC120VAC120VAC120VAC

Fan

NoNoNoYes

OutputCurrent

10A10A20A40A

Xantrex Truecharges are microprocessor controlled for fast and accurate three-stage charging ofall deep-cycle house batteries. Features such as adjustable temperature compensation andindependent settings for flooded, gel and AGM batteries prevent battery damage due toovercharging. All feature over-temperature shutdown, and reverse polarity, short circuit and surgeprotection. The Truecharge 10 is a portable charger with an AC power cord and clip leads for DCconnection and is recommended for flooded and gel battery banks rated 200 amp hours orlower. The Truecharge 20 and Truecharge 40 offer high frequency power conversion with manyfeatures including overload protection and equalization mode. CSA/NRTL certified to UL andCSA standards. Charger efficiency approx. 85%. One-year warranty.

Xantrex

Xantrex Truecharge

Output Output Input Dimensions WeightModel Voltage Current Voltage LxWxH (lbs) MSRP

DLS15 13.6/14.2 VDC 15A 120VAC 7.0” x 6.5” x 3.5” 4.0 $149.00DLS30 13.6/14.2 VDC 30A 120VAC 7.0” x 6.5” x 3.5” 5.5 $199.00DLS45 13.6/14.2 VDC 45A 120VAC 7.0” x 6.5” x 3.5” 5.5 $229.00DLS55 13.6/14.2 VDC 55A 120VAC 10.0” x 6.5” x 3.5” 5.5 $269.00DLS75 13.6/14.2 VDC 75A 120VAC 10.0” x 6.5” x 3.5” 7.8 $555.00

IQ4 Smart ControllerThe IQ Smart Controller offers automatic charging control for the DLS Series Chargers to providelonger and safer use of the system’s battery. IQ4 controllers feature an installation jack plugwhich plugs into the dual voltage jack on the top of the DLS unit. The IQ Controller allows theDLS charger to operate as an automatic 3-stage smart charger. For 12V only. Two-year warranty.

Model Dimensions Weight MSRPIQ4 Smart Controller 3.06” x 1.88” x 1.44” 1 lb $38.00Iota IQ4

Iota ITS-30R

ITS Transfer SwitchesThe ITS-30 and 50R are relay-based automatic transfer switches and the ITS-75C is contactor-based . They provide switching between two separate power sources and can be used inconjunction with another ITS transfer switch for additional power sources.

Max Max Max Main Case WeightModel Powercord Size Generator Breaker Material Wiring Dimensions (lbs) MSRPITS-30R 30A 4kW 30A 1P Plastic Hard Wire 7.5” x 8.5” x 4” 2 $95.00ITS-50R 50A 12kW 50A 2P Plastic Bridge 7.5” x 8.5” x 4” 3 $225.00ITS-75C 75A 18kW 75A 2P Steel Lugs 8.0” x 12” x 4” 11.6 $590.00



Battery Chargers

DLS SeriesThe DLS Series Charger/Power Supply uses switch-mode technology to insure service freeoperation even when subjected to extremely harsh conditions. The clean DC output operatesradios and televisions without causing annoying static or snow. Pumps, motors, lights and fansoperate perfectly for prolonged life. They feature regulated converter/power supply, tight line-loadregulation, two-step voltage switch, current limiting, transient voltage protection and shortcircuit/over-current protection. The DLS maintains the batteries, only putting into the battery whatis required by load or self-discharge, cutting back to milliamps as the battery requires. All modelsinclude cooling fan. Charger efficiency approx. 85%. Two-year warranty.

Iota Engineering Company

Iota DLS 55

BATT

ERIE

S

3/03

Model

Truecharge 10 – 1 bank clip leadTruecharge 10TB – 2 bank hardwireTruecharge 20+ – 3 bankTruecharge 40+ – 4 bankACCESSORIESDisplay Panel - True Charge 20+Display Panel - True Charge 40+Temperature Sensor - True Charge 20/40

MSRP

$200.00$160.00$340.00$450.00

$40.00$40.00$30.00

OutputVoltage

13.8/14.8 VDC14.2/14.4 VDC13.8/14.8 VDC13.8/14.8 VDC

Dimensions LxWxH

9.0” x 6.5” x 2.75”10.65“ x 6.5” x 2.75”15.0“ x 6.5” x 2.75”15.0” x 6.5” x 2.75”

Weight(lbs)

3.03.05.57.5

InputVoltage

120VAC120VAC120VAC120VAC

Fan

NoNoNoYes

OutputCurrent

10A10A20A40A

Xantrex Truecharges are microprocessor controlled for fast and accurate three-stage charging ofall deep-cycle house batteries. Features such as adjustable temperature compensation andindependent settings for flooded, gel and AGM batteries prevent battery damage due toovercharging. All feature over-temperature shutdown, and reverse polarity, short circuit and surgeprotection. The Truecharge 10 is a portable charger with an AC power cord and clip leads for DCconnection and is recommended for flooded and gel battery banks rated 200 amp hours orlower. The Truecharge 20 and Truecharge 40 offer high frequency power conversion with manyfeatures including overload protection and equalization mode. CSA/NRTL certified to UL andCSA standards. Charger efficiency approx. 85%. One-year warranty.

Xantrex

Xantrex Truecharge

Output Output Input Dimensions WeightModel Voltage Current Voltage LxWxH (lbs) MSRP

DLS15 13.6/14.2 VDC 15A 120VAC 7.0” x 6.5” x 3.5” 4.0 $149.00DLS30 13.6/14.2 VDC 30A 120VAC 7.0” x 6.5” x 3.5” 5.5 $199.00DLS45 13.6/14.2 VDC 45A 120VAC 7.0” x 6.5” x 3.5” 5.5 $229.00DLS55 13.6/14.2 VDC 55A 120VAC 10.0” x 6.5” x 3.5” 5.5 $269.00DLS75 13.6/14.2 VDC 75A 120VAC 10.0” x 6.5” x 3.5” 7.8 $555.00

IQ4 Smart ControllerThe IQ Smart Controller offers automatic charging control for the DLS Series Chargers to providelonger and safer use of the system’s battery. IQ4 controllers feature an installation jack plugwhich plugs into the dual voltage jack on the top of the DLS unit. The IQ Controller allows theDLS charger to operate as an automatic 3-stage smart charger. For 12V only. Two-year warranty.

Model Dimensions Weight MSRPIQ4 Smart Controller 3.06” x 1.88” x 1.44” 1 lb $38.00Iota IQ4

Iota ITS-30R

ITS Transfer SwitchesThe ITS-30 and 50R are relay-based automatic transfer switches and the ITS-75C is contactor-based . They provide switching between two separate power sources and can be used inconjunction with another ITS transfer switch for additional power sources.

Max Max Max Main Case WeightModel Powercord Size Generator Breaker Material Wiring Dimensions (lbs) MSRPITS-30R 30A 4kW 30A 1P Plastic Hard Wire 7.5” x 8.5” x 4” 2 $95.00ITS-50R 50A 12kW 50A 2P Plastic Bridge 7.5” x 8.5” x 4” 3 $225.00ITS-75C 75A 18kW 75A 2P Steel Lugs 8.0” x 12” x 4” 11.6 $590.00


INVERTERS

3/03

Inverters

Choose the Right Inverter for Your Application

Now that you are producing your solar electricity you want to use it to run some appliances (or loads) and possibly sell someback to the utility company where net metering is available. In order to do this, you need an inverter to change the direct current(DC) electricity generated by solar or wind into the alternating current (AC) used by households and the electric company.

Inverters, like every other product category mentioned thus far, come in many flavors. Depending on the model, the AC output of invertersis either a modified or pure sine wave. Modified sine wave power is suitable for some loads but not loads requiring a good clean wavesuch as electronics – home theater systems, high end TV’s, and computers. For these loads you need a pure sine wave inverter.

Some inverters include a battery charger and transfer switch to charge a battery bank when utility or generator power is available.Once the battery is charged, the inverter automatically disconnects from the power source and begins providing AC power againin order to run the loads from the battery bank. For grid-tie only systems there is no battery bank. Inverters are connected to aproperly configured solar array and the solar energy is converted directly into AC power and fed into the home or electric grid.

Inverters are sized based on the required AC output. If you have a 1 amp, 110 VAC load, you only need a 150 watt inverter. Awhole home may need stacked 5,500 watt inverters. As always, it’s best to do your research then consult with your localSunWize dealer to select the equipment that best suits your application.

FX 2000 InvertersThe FX2000 is a 2kW modular “building” block pure sine wave inverter with a battery charger andAC transfer switch. Additional FX2000’s can be connected in series for 240 VAC, parallel at 120VAC, or three-phase configurations. Up to eight FX2000s can be connected together to provide upto 16 kW of continuous power conversion capacity. The sealed, gasketed die-cast aluminumchassis protects and keeps the power conversion components cool. Two-year warranty.


FX 2000 Inverter

DC Voltage Continuous Charger AC VoltsModel Efficiency Input Power Current Output Dimensions Weight MSRP

FX2024 97% 24 VDC 2000 W 55A 120VAC 16.25” x 8.25” x 11.5” 60 lbs $1795.00FX2548 97% 48 VDC 2500 W 35A 120VAC 16.25” x 8.25” x 11.5” 60 lbs $2245.00

AccessoriesFX-DCC DC Cover for FX2000, protects DC cable connections $65.00FX-DCA DC Conduit Adapter allows direct mounting to a PSDC or connection of 2” conduit. Includes 2” snap-in bushing $45.00FX-ACA AC Adapter extends the AC wiring compartment. Required for connection to PSAC enclosure $35.00FXA Adapter Kit includes both FX-DCA and FX-ACA adapters and FX-DCC cover $129.00RTS Remote Temperature Sensor with 20 foot cable $29.00STACK-2 Stacking Kit for 2-FX2000’s. Allows for connection for two inverters in series or parallel $85.00X-240 Auto transformer, 4kVA 120/240 step up/down or generator balancing. Includes 25A, 2-pole breaker $290.00X-Fan Fan kit for X-240. Increases power to maximum of 6kVA continuous $29.00

Mate The Mate is a complete system controller and display for both the FX2000 and MX60 chargecontroller (see Controller section). It provides a display of operation and allows control andsetpoint adjustment. The Mate also coordinates the entire system operation. A single Mate isable to connect to multiple FX2000 inverters. It includes a 4-line backlit LCD display, a real timeclock and calendar and an opto-isolated RS232 port with a DB9 jack. All programmed setpointsare stored in permanent memory. Two-year warranty.

Outback Mate

Model Description Dimensions Weight MSRP

MATE OutBack digital display and system control unit with 50 ft cable 5.75” x 4.25” x 2” 1 lb $295.00HUB-4 Communication Manager allows up to 4 FX2000 inverters/ MX60controllers to be

connected to a single MATE. $195.00CATV-6 Communications cable CATV.5e, 6 ft. long with RJ45 plug $8.00CATV-50 Communications cable CATV.5e, 50 ft. long with RJ45 plug $25.00

Inverters

INVE

RTER

S

42 3/03

SW Series Inverter

SW SeriesThe SW Series is a pure sine wave DC-AC power conversion inverter for use in off-grid, grid-tieand backup power applications. This inverter provides three-stage battery charging with aremote temperature sensor for increased performance. Other features include a programmablecontrol module with LCD display and LED indicators, and a low idle current that conservesenergy when no loads are present. UL listed to UL 1741, two-year warranty.

Sun Tie XR™ SeriesThe Sun Tie XR inverter is designed to be the link between your solar array and the utility. Thisgrid-tie inverter features Sunsweep™ maximum power point tracking (MPPT), LCD user display,combined AC/DC surge protection, and DC and AC input/ output breakers. Using a standardtelephone cable, the optional remote meter allows you to scroll through multiple screens, whichdisplay daily, weekly, monthly and cumulative energy production, as well as other systemperformance data. Complies with IEEE 929 standards for grid tie operation. UL listed to UL 1741and cUL listed to CSA C22.2. Not designed for use with batteries. Two year warranty.Features:• User display shows system status and daily energy harvest (Whr)• Sine wave output 240 VAC, 60 Hz, single phase, high frequency PWM controlled• AC Disconnect - standard double-pole 15 amp, 240 VAC branch rated circuit breaker• DC Disconnect - standard single-pole 100 amp, DC rated circuit breaker• PV ground fault protection system on 1500W and 2500W units • Lightning arrestor• PV combiner board with 6 fused inputs, 20 amps maximum per input on 1500W and 2500W units.

Xantrex

Efficiency DC Voltage Continuous UnitModel (peak) Input Power Dimensions Weight (lbs) MSRP

STXR1000 92% 42-85 VDC 1000 VA 33.25” x 13.25” x 5.30” 35 $1,849.00STXR1500 92% 42-85 VDC 1500 VA 33.25” x 13.25” x 5.30” 35 $2,239.00STXR2000 94% 42-85 VDC 2000 VA 33.25” x 13.25” x 5.30” 35 $2,259.00STXR2500 94% 42-85 VDC 2500 VA 33.25” x 13.25” x 5.30” 35 $2,759.00

AccessoriesSTRS Protective rain shield, required for installation outdoors $125.00STRM Remote display unit for status, resettable Whr meter, tech menu, and daily energy harvest w/50 ft. cable $179.00

Sun Tie XR Inverter shown with optional rain shield

Efficiency DC Voltage Continuous Charger AC Volts Dimensions UnitModel (peak) Input Power Current Output LxWxH Weight (lbs) MSRP

SW4024 94% 24V 4.0kVA 120 amp 120 VAC 60 Hz 22.5” x 15” x 9.0” 105 $3,495.00


SW5548 96% 48V 5.5kVA 75 amp 120 VAC 60 Hz 22.5” x 15” x 9.0” 136 $3,995.00SW Accessories

SWCA Sine wave communications adapter allows PC connection and monitoring of up to eight SW Series inverters – includes adapter, DOS based software, 50’ of cable and DB9 connector $175.00

SWRC Full function remote control with LCD display for all SW inverters with 25’ cable $295.00

SWRC/50ft Full function remote control with LCD display for all SW inverters with 50’ cable $329.00

SWI/PAR Sine wave paralleling kit – connects 2 identical SW inverters together for twice theoutput power at the same voltage $345.00

SWI Series stacking interface for 2 identical SW inverters, provides 120/240 VAC,3 wire 240 VAC, Doubles output $45.00

SWCB Conduit box for SW Series – fits on the DC end of the inverter (1/2”, 3/4” and 2” knockouts) - adds 6” $94.00

GTI Grid Tie Interface, an integrated assembly that allows you to connect the SW to the utility grid.Provides active anti-islanding protection and reduces current total harmonic distortion. $449.00


INVE

RTER

S

42 3/03

Inverters

SW Plus Inverter

SW Plus Designed to provide homes with a completely independent power supply, the SW Plus combinesan inverter, battery charger and dual transfer switch in one package. The SW Plus provides puresine wave AC power for household appliances and DC power to charge batteries. As part of anoff-grid renewable power system, it converts all forms of renewable energy into utility grade house-hold power. The SW Plus can also be used as part of a backup power system to automaticallyprovide AC power when utility power fails. With a high surge capacity, the SW Plus can start highpower loads such as deep well pumps and compressors. A “Smart Energy Management” systemcontrols utility and/or generator usage. Features include forced air cooling, multi-stage charging,control panel and a battery temperature sensor. The Sine Wave Interface (SWI) can be used tostack two SW Plus for double the power output. CSA listed to UL 1741. Two-year warranty.

Xantrex


SW Plus 2524 95% 24 VDC 2500 W 60 A 120 VAC 15” x 22.5” x 9” 105 lbs $2299.00SW Plus 2548 95% 48 VDC 2500 W 60 A 120 VAC 15” x 22.5” x 9” 105 lbs $2299.00

AccessoriesGSM Generator Start Module - automatic generator control system for two and three wire start AC and DC generators $159.00ALM Auxiliary Load Module - User adjustable voltage controlled signal relays for control of loads or charging sources $159.00ICM Remote Inverter Control Module - full function remote control with LCD and LED indicators CallDCCB Side mount conduit box for code-compliant DC wiring connections - USA CallDCCB-F Side mount conduit box for code-compliant DC wiring connections with fuse - Canada CallACCB Side mount conduit box for code-compliant AC wiring (bypass/disconnect circuit breaker) Call

SW Series Inverter

SW SeriesThe SW Series is a pure sine wave DC-AC power conversion inverter for use in off-grid, grid-tieand backup power applications. This inverter provides three-stage battery charging with aremote temperature sensor for increased performance. Other features include a programmablecontrol module with LCD display and LED indicators, and a low idle current that conservesenergy when no loads are present. UL listed to UL 1741, two-year warranty.

Efficiency DC Voltage Continuous Charger AC Volts Dimensions UnitModel (peak) Input Power Current Output LxWxH Weight (lbs) MSRP



SW5548 96% 48V 5.5kVA 75 amp 120 VAC 60 Hz 22.5” x 15” x 9.0” 136 $3,995.00SW Accessories

SWCA Sine wave communications adapter allows PC connection and monitoring of up to eight SW Series inverters – includes adapter, DOS based software, 50’ of cable and DB9 connector $175.00

SWRC Full function remote control with LCD display for all SW inverters with 25’ cable $295.00

SWRC/50ft Full function remote control with LCD display for all SW inverters with 50’ cable $329.00

SWI/PAR Sine wave paralleling kit – connects 2 identical SW inverters together for twice theoutput power at the same voltage $345.00

SWI Series stacking interface for 2 identical SW inverters, provides 120/240 VAC,3 wire 240 VAC, Doubles output $45.00

SWCB Conduit box for SW Series – fits on the DC end of the inverter (1/2”, 3/4” and 2” knockouts) - adds 6” $94.00

GTI Grid Tie Interface, an integrated assembly that allows you to connect the SW to the utility grid.Provides active anti-islanding protection and reduces current total harmonic distortion. $449.00



INVERTERS

3/03

Inverters

SW Plus Inverter

SW Plus Designed to provide homes with a completely independent power supply, the SW Plus combinesan inverter, battery charger and dual transfer switch in one package. The SW Plus provides puresine wave AC power for household appliances and DC power to charge batteries. As part of anoff-grid renewable power system, it converts all forms of renewable energy into utility grade house-hold power. The SW Plus can also be used as part of a backup power system to automaticallyprovide AC power when utility power fails. With a high surge capacity, the SW Plus can start highpower loads such as deep well pumps and compressors. A “Smart Energy Management” systemcontrols utility and/or generator usage. Features include forced air cooling, multi-stage charging,control panel and a battery temperature sensor. The Sine Wave Interface (SWI) can be used tostack two SW Plus for double the power output. CSA listed to UL 1741. Two-year warranty.

Xantrex


SW Plus 2524 95% 24 VDC 2500 W 60 A 120 VAC 15” x 22.5” x 9” 105 lbs $2299.00SW Plus 2548 95% 48 VDC 2500 W 60 A 120 VAC 15” x 22.5” x 9” 105 lbs $2299.00

AccessoriesGSM Generator Start Module - automatic generator control system for two and three wire start AC and DC generators $159.00ALM Auxiliary Load Module - User adjustable voltage controlled signal relays for control of loads or charging sources $159.00ICM Remote Inverter Control Module - full function remote control with LCD and LED indicators CallDCCB Side mount conduit box for code-compliant DC wiring connections - USA CallDCCB-F Side mount conduit box for code-compliant DC wiring connections with fuse - Canada CallACCB Side mount conduit box for code-compliant AC wiring (bypass/disconnect circuit breaker) Call

DR SeriesThe DR Series inverter is a robust, proven performer designed for remote, medium sized, off-gridand utility backup systems in residential and commercial applications. This modified sine waveinverter comes with a three-stage battery charger and automatic AC transfer relay. LED statusindicators show charge mode, high or low battery voltage and over temperature or over load.Selectable settings for FLA, gel and AGM batteries. ETL listed to UL 1741.Two-year warranty.

DR Series Inverter


DR1512 94% 12V 1.5 kVA 70 amp 120VAC 60Hz 21.5” x 8.5" x 7.25" 35 $850.00

DR1524 94% 24V 1.5 kVA 35 amp 120VAC 60Hz 21.5" x 8.5" x 7.25" 35 $850.00

DR2412 94% 12V 2.4 kVA 120 amp 120VAC 60Hz 21.5" x 8.5" x 7.25" 45 $1,100.00



DR1512E 94% 12V 1.5 kVA 70 amp 230VAC/50Hz 21.5" x 8.5" x 7.25" 35 $850.00

DR1524E 94% 24V 1.5 kVA 35 amp 230VAC 50Hz 21.5" x 8.5" x 7.25" 35 $850.00

DR1548E 94% 48V 1.5 kVA 15 amp 230VAC 50Hz 21.5" x 8.5" x 7.25" 35 $850.00

DR2424E 95% 24V 2.4 kVA 70 amp 230VAC 50Hz 21.5" x 8.5" x 7.25" 45 $1,100.00

AccessoriesDRI Stacking interface for 2 DR inverters, providing 120/240 VAC, 3 wire 240 VAC–(doubles output) $85.00

includes two 1.5’ battery cables and the stacking comm. cable (not for use with E models)

DRCB Conduit box for all DR’s - fits either end - AC/DC (1/2”, 3/4” and 2” knockouts), adds 6” $69.00

Inverters

UX SeriesThe UX Series is a modified sine wave inverter designed for small off-grid and utility backupapplications of between 500 and 1400 watts. The standby (SB) option provides temperaturecompensation, three-stage battery charging and an AC input transfer switch. UL listed. E modelscarry the CE mark. Two-year warranty.

Xantrex

UX Series Inverter

INVE

RTER

S

3/03

12V12V12V12V12V12V12V12V12V12V

.5 kVA

.5 kVA

.6 kVA

.6 kVA1.1 kVA1.1 kVA1.1 kVA1.1 kVA1.4 kVA1.4 kVA

N/A25 amp

N/A25 amp

N/A35 amp

N/A50 amp

N/A50 amp

230VAC 50Hz230VAC 50Hz120VAC 60Hz120VAC 60Hz120VAC 60Hz120VAC 60Hz230VAC 50Hz230VAC 50Hz120VAC 60Hz120VAC 60Hz

6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”6” X 15.5” X 10.25”

26262626303030303535

$595.00$695.00$595.00$695.00$795.00$895.00$729.00$829.00$885.00$985.00

Model DC Voltage Continuous Charger AC Volts Dimensions WeightInput Power Current Output LxWxH (lbs) MSRP

Efficiency(peak)

92%92%92%92%90%90%90%90%92%92%

UX512EUX512ESB*UX612UX612SB*UX1112UX1112SB*UX1112EUX1112ESB*UX1412UX1412SB*

* with standby option

TS SeriesThe TS Series is a modified sine wave inverter with a three-stage battery charger and automatictransfer relay. Designed for small, off-grid and utility backup applications. Two-year warranty.

TS Series Inverter

Efficiency DC Voltage Continuous Charger AC Volts WeightModel (peak) Input Power Current Output Dimensions (lbs) MSRP

TS512SB 90% 12VDC 500VA 15 amp 120VAC/60Hz 14" x 5.75" x 5.38" 17 $495.00TS524SB 90% 24VDC 500VA 7.5 amp 120VAC/60Hz 14" x 5.75" x 5.38" 17 $495.00TS812SB 90% 12VDC 800VA 25 amp 120VAC/60Hz 14" x 5.75" x 5.38" 17 $595.00TS412ESB 90% 12VDC 400VA 15 amp 230VAC/50Hz 14" x 5.75" x 5.38" 17 $495.00TS424ESB 90% 24VDC 400VA 7.5 amp 230VAC/50Hz 14" x 5.75" x 5.38" 17 $495.00

Freedom 458With filtered modified sine wave output, Freedom inverter/chargers run virtually anything from officeequipment to household appliances and electronics. Temperature controlled multistage chargingensures your batteries are recharged quickly, and automatic shutdown and other safety featuresprotect your deep-cycle batteries from excessive depletion. Programmable front panel and LEDindicators. Built-in transfer switch. UL listed. 30-month warranty. For advanced battery monitoringand remote control, Freedom 458 systems can be paired with Link instrumentation (see page 31).

Freedom 458 10-12 Inverter

Efficiency DC Voltage Continuous Charger AC Volts WeightModel (peak) Input Power Current Output Dimensions (lbs) MSRP

Freedom 458 10-12 85% 12 V 1000 W 50 amp 120VAC 14” x 11.5” x 7.75” 34 lbs $975.00Freedom 458 15-12 86% 12 V 1500 W 75 amp 120VAC 14” x 11.5” x 7.75” 45 lbs $1,125.00Freedom 458 20-12 85% 12 V 2000 W 100 amp 120VAC 14” x 11.5” x 7.75” 45 lbs $1,225.00Freedom 458 25-12* 87% 12 V 2500 W 130 amp 120VAC 14” x 11.5” x 7.75” 50 lbs $1,425.00Freedom 458 30-12 86% 12 V 3000 W 140 amp 120VAC 14” x 11.5” x 7.75” 50 lbs $1,625.00Freedom Basic Remote (84-2056-01) optional remote for system monitoring $150.00

* dual input, dual output


INVERTERS

3/03 45

Inverters

PROsine 1000 Inverter

XantrexPROsine InvertersOffering quality true sine wave output, the PROsine inverter is ideally suited for electrical systems thatalready have a quality multistage battery charger. Designed for recreational and industrial applications,its output is capable of handling both heavy duty and smaller, multiple AC loads. A removable LCDdisplay can be mounted remotely for control and monitoring. The powersave mode draws only 1.5watts under no load. 230VAC/50 Hz models available. Two-year warranty.


PROsine 2.0 87% 12 V 2.0kVA 100 A 120VAC 17.7” x 11” x 5.7” 24 lbs $2,000.00

PROsine 2.0 87% 12 V 2.0kVA 100 A 120VAC 17.7” x 11” x 5.7” 24 lbs $2,000.00w/GFCI outlets


PROsine 2.5/24V 88% 24 V 2.5kVA 50 A 120VAC 20.0” x 15” x 7.0” 32 lbs $2,860.00


PROsine 3.0/24V 88% 24 V 3.0kVA 60 A 120VAC 20.0” x 15” x 7.0” 32 lbs $3,300.00

Temperature Sensor – Remote battery temperature sensor for PROsine 2.5/3.0 $30.00

PROsine 2.5 Inverter

PROsine Inverter/ChargersA powerful all-in-one solution, PROsine inverter/chargers deliver clean true sine wave outputpower for all types of appliances along with three-stage charging for longer battery life. Invertersinclude a full function remote control panel and battery temperature sensor. Built in transferswitch. CSA/NRTL certified. Two-year warranty.

DC Voltage Continuous Surge AC VoltsModel Efficiency Input Power Capacity Output Dimensions Weight MSRP

PROwatt 150 90% 12 V 150 W 400 W 115 VAC 2.0” x 4.7” x 4.7” 22 oz $40.00

PROwatt 250– 24 90% 24 V 225 W 500 W 115 VAC 1.5” x 4.5” x 6.0” 26 oz $136.00

PROwatt 300 90% 12 V 300 W 500 W 115 VAC 2.0” x 4.7” x 6.3” 1.8 lbs $60.00

PROwatt 400 90% 12 V 400 W 800 W 115 VAC 1.8” x 4.7” x 6.3” 2 lbs $80.00

PROwatt Inverter

PROwatt Low Powered Handheld InvertersThe modified sine wave handheld PROwatt inverters plug into a 12 volt lighter socket of avehicle, boat or RV to provide continuous power suitable for a variety of electronics. The exactrun time depends on the amount of power drawn by the application. One-year warranty.

DC Voltage Continuous AC VoltsModel Efficiency Input Power Output Dimensions Weight MSRP

PROsine 1000 89% 12 V 1.0kVA 120VAC 15.4” x 11.5” x 4.5” 14.5 lbs $890.00PROsine 1000/24V 90% 24 V 1.0kVA 120VAC 15.4” x 11.5” x 4.5” 14.5 lbs $980.00PROsine 1800 89% 12 V 1.8kVA 120VAC 15.4” x 11.5” x 4.5” 16.5 lbs $1,300.00PROsine 1800/24V 90% 24 V 1.8kVA 120VAC 15.4” x 11.5” x 4.5” 16.5 lbs $1,430.00

Models with hardwire/15 amp AC Transfer Relay:PROsine 1000 HW/TR 89% 12V 1.0kVA 120VAC 15.4” x11.5” x 4.5” 14.5lbs $940.00PROsine 1000/24V HW/TR 90% 24V 1.0kVA 120VAC 15.4” x11.5” x 4.5” 14.5lbs $1,030.00PROsine 1800 HW/TR 89% 12V 1.8kVA 120VAC 15.4” x11.5” x 4.5” 16.5lbs $1,350.00PROsine 1800/24V HW/TR 90% 24V 1.8kVA 120VAC 15.4” x11.5” x 4.5” 16.5lbs $1,480.00

Remote Interface Kit – Allows LCD panel to be removed - includes 25’ of cable and replacement on/off switch panel for inverter cavity $50.00


Inverters

INVE

RTER

S

46 3/03

PROwatt Mid to High Powered InvertersThese PROwatt inverters are designed to operate a wide range of applications includinghousehold products, recreational, large single loads, and high power industrial. All modelsprovide standard protection. The PROwatt 800 to 1500 models feature a dual GFCI outlet,addition of external AC outlets, a built-in LED display for volts and amps, and a remote on/offswitch. The PROwatt 1750 and 3000 models include heavy-duty terminals for trouble-freebattery connection. One-year warranty.

Xantrex

PROwatt 3000 Inverter


PROwatt 600 90% 12 V 600 W 1200 W 115 VAC 2.5” x 6.25” x 11” 4.1 lbs $130.00





PROwatt 3000 90% 12 V 2500 W 5000 W 115 VAC 6.25” x 8” x 18.5” 20.0 lbs $800.00


PROwatt 150 90% 12 V 150 W 400 W 115 VAC 2.0” x 4.7” x 4.7” 22 oz $40.00

PROwatt 250– 24 90% 24 V 225 W 500 W 115 VAC 1.5” x 4.5” x 6.0” 26 oz $136.00


PROwatt 400 90% 12 V 400 W 800 W 115 VAC 1.8” x 4.7” x 6.3” 2 lbs $80.00

PROwatt Inverter

PROwatt Low Powered Handheld InvertersThe modified sine wave handheld PROwatt inverters plug into a 12 volt lighter socket of avehicle, boat or RV to provide continuous power suitable for a variety of electronics. The exactrun time depends on the amount of power drawn by the application. One-year warranty.


INVERTERS

3/03

Inverters

Sunny Boy 2500

Sunny BoyThe Sunny Boy line of inverters are applicable for 700 W to 1 MW of PV grid tie power with aconversion efficiency > 93%. The basic principle of the Sunny Boy inverters is that one inverteris used per string of modules; where typical configurations use several strings of modules inparallel to achieve rated power, the Sunny Boy uses modules wired in series at a high DCvoltage. String inverters are also easily paralleled to increase energy efficiency. The result isincreased efficiency and great savings in wire costs, eliminating the losses due to mismatchingand the need for a combiner box, blocking diodes, and high current DC breakers or fuses. ULlisted and CE certified. Five-year warranty.

If you need monitoring, nothing could give you more options than the Sunny Boy inverter andcontrol unit. The inverter can be purchased with a two line LCD display with backlight that willgive you all the relevant PV data (model SBD). The inverter also automatically reads real timedata, at a 132.45kHz frequency, over the 60Hz sinewave. This is called power line transmission,and it means no additional cabling needed. To input this data into a PC, buy the SWR-COMsocket modem that plugs into any outlet and broadcasts the power line transmission to a PCcom port. Supply voltage, 0-260V, 50-60Hz.

Data logging requires purchasing one of the three control units, the Sunny Boy Control Light, theSunny Boy Control, or the Sunny Boy Control Plus. The control units can receive data via thepower line transmission, RS232 or RS485 connection. The control units will allow you to storedata from 1 to 50 inverters, monitor the data and, via an external customer supplied modem,send data or fault alarms to an email, a FAX, or a pager. LCD display. Ambient temperature 0˚Cto 40˚C.

Software to monitor either the inverter power line transmission output or the control unit’s outputis provided free of charge. The software provides an excellent GUI for monitoring small, 5-module systems to large-scale power stations.

SMA America

Sunny Boy Control Unit

DC Voltage Continuous AC VoltsModel Efficiency Input Power Output Dimensions Weight MSRP

SWR 2500U 93% 275-550 V 2500 W 240 VAC 8.4” x 11.6” x 17” 70.5 lbs $2,750.00SWR 2500U SBD 93% 275-550 V 2500 W 240 VAC 8.4” x 11.6” x 17” 70.5 lbs $2,950.00(with LCD display)

SWR 2500U SBD 208 93% 275-550 V 2100 W 208 VAC 8.4” x 11.6” x 17” 70.5 lbs $3,050.00(with LCD display, for connection to 3 phase utility systems)

SWR 1800U 93% 150-400 V 1800 W 120 VAC 8.4” x 11.6” x 17” 59.5 lbs $2,350.00

SWR 1800U SBD 93% 150-400 V 1800 W 120 VAC 8.4” x 11.6” x 17” 59.5 lbs $2,550.00(with LCD display)

Communication Accessory EquipmentSBD 2 line LCD display with back light for Sunny Boy inverters $289.00SBSL Cover lid for Sunny Boy inverters $139.00SB RS-232-N RS-232 Module for use in Sunny Boy inverters $179.00SB RS-485-N RS-485 Module for use in Sunny Boy inverters $179.00SB 232 SERV Sunny Boy PC Service cable $229.00SB NLM-N Power Line Carrier Module for use in Sunny Boy Inverters $159.00XPCP Power line carrier phase coupler for 120/208/240 VAC circuits $79.00PZZ001 Power line carrier coupler for 208/240 VAC 3-phase circuits $109.00XPPF Plug-in filter for 120 VAC wall sockets, 5A $62.00XPF In-line noise filter for 120/240 VAC circuits $123.00

Monitoring and Data Collection EquipmentSBC Light Sunny Boy Control Light $669.00SBC Sunny Boy Control $1,125.00SBC-485 Sunny Boy Control with RS-485 communication card $1,295.00SBC Plus Sunny Boy Control Plus with 8 analog inputs and additional port $2,250.00SBC Plus-485 Sunny Boy Control Plus w/ RS-485 communication card $2,395.00RS232 Cable RS232 Communication Cable, 15 meter $110.00RS485 Cable RS485 Cable Communication Cable, 15 meter $110.00


Inverters

INVE

RTER

S

48 3/03

Genius™

Continuous Surge TareModel Voltage Power Power Loss* Dimensions Weight MSRP

DC-AC Modified Sine Waver Inverter with 3 amp Battery Charger

G-12-060C 12V 600W 1500W <10W 12.99” x 8.07” x 2.87” 6.16 lbs $135.00

G-12-100C 12V 1000W 2000W <15W 18.7” x 9.53” x 3.15” 10.23 lbs $189.00

G-12-150C 12V 1500W 3000W <20W 18.7” x 9.53” x 3.15” 10.23 lbs $299.00

DC-AC Modified Sine Wave Inverter

G-12-030 12V 300W 1000W <4W 9.84” x 4.09” x 2.28” 1.98 lbs $50.00

G-12-060 12V 600W 1500W <7W 11.41” x 8.07” x 2.87” 4.62 lbs $95.00

G-12-080 12V 800W 2000W <5W 12.99” x 9.45” x 3.03” 5.94 lbs $135.00

G-12-100 12V 1000W 2000W <6W 15.47” x 9.53” x 3.15” 6.93 lbs $169.00

G-12-150 12V 1500W 3000W <7W 16.93” x 9.49 x 3.03 16.5 lbs $239.00

G-12-250 12V 2500W 5000W <7W 19.53” x 7.99” x 6.54” 20 lbs $550.00

Pure Sine Wave Inverter – 95% Efficient

G-12-250S 12V 250W 750W <4W 9.84” x 4.09” x 2.28” 1.98 lbs $139.00

Genius high efficiency, 100% solid state inverters feature low battery alarm, low battery shutdown, overload and short circuit protection, thermal protection and a cooling fan. All models:120VAC, 60Hz output. Battery cables included. UL listed, CSA approved and CE certified. 90%efficiency, one-year warranty. Note: Tare loss is less than 1 watt with switch “off”.

XP SeriesExeltech XP Series are lightweight, high-performance, pure sine wave inverters that operate anytype of load. All models are 120VAC, 60 Hz. 85% efficiency, 100% solid state. These invertersinclude protection circuitry for over and under voltage, over temperature and short circuits.Painted aluminum finish and a full year parts and labor warranty. UL listed.

Exeltech

Model/Description

XP125–12

XP250–12

XP250–24

XP600–12*

XP600–24*

XP1100–12*

XP1100–24*

MSRP

$289.00

$560.00

$560.00

$785.00

$785.00

$935.00

$1,020.00

Voltage

12V

12V

24V

12V

24V

12V

24V

ContinuousPower

125W

250W

250W

600W

600W

1100W

1100W

Dimensions DxWxH

7.90” x 4.93” x 2.16”

12.03” x 5.23” x 2.77”

12.03” x 5.23” x 2.77”

12.10” x 7.70” x 3.60”

12.10” x 7.70” x 3.60”

15.05” x 7.70” x 3.60”

15.05” x 7.70” x 3.60”

Weight

2 lbs

5 lbs

5 lbs

6.5 lbs

6.5 lbs

10 lbs

10 lbs

Surge Power

150W

300W

300W

1100W

1100W

2200W

2200W

TareLoss

5W

5W

6W

8W

8W

20W

20W

* cooling fan

XP Series Inverter

G-12-060C

G-12-250S

G-12-030



Inverters

INVE

RTER

S

48 3/03

Genius™


DC-AC Modified Sine Waver Inverter with 3 amp Battery Charger

G-12-060C 12V 600W 1500W <10W 12.99” x 8.07” x 2.87” 6.16 lbs $135.00

G-12-100C 12V 1000W 2000W <15W 18.7” x 9.53” x 3.15” 10.23 lbs $189.00

G-12-150C 12V 1500W 3000W <20W 18.7” x 9.53” x 3.15” 10.23 lbs $299.00

DC-AC Modified Sine Wave Inverter

G-12-030 12V 300W 1000W <4W 9.84” x 4.09” x 2.28” 1.98 lbs $50.00

G-12-060 12V 600W 1500W <7W 11.41” x 8.07” x 2.87” 4.62 lbs $95.00

G-12-080 12V 800W 2000W <5W 12.99” x 9.45” x 3.03” 5.94 lbs $135.00

G-12-100 12V 1000W 2000W <6W 15.47” x 9.53” x 3.15” 6.93 lbs $169.00

G-12-150 12V 1500W 3000W <7W 16.93” x 9.49 x 3.03 16.5 lbs $239.00

G-12-250 12V 2500W 5000W <7W 19.53” x 7.99” x 6.54” 20 lbs $550.00

Pure Sine Wave Inverter – 95% Efficient

G-12-250S 12V 250W 750W <4W 9.84” x 4.09” x 2.28” 1.98 lbs $139.00

Genius high efficiency, 100% solid state inverters feature low battery alarm, low battery shutdown, overload and short circuit protection, thermal protection and a cooling fan. All models:120VAC, 60Hz output. Battery cables included. UL listed, CSA approved and CE certified. 90%efficiency, one-year warranty. Note: Tare loss is less than 1 watt with switch “off”.

XP SeriesExeltech XP Series are lightweight, high-performance, pure sine wave inverters that operate anytype of load. All models are 120VAC, 60 Hz. 85% efficiency, 100% solid state. These invertersinclude protection circuitry for over and under voltage, over temperature and short circuits.Painted aluminum finish and a full year parts and labor warranty. UL listed.

Exeltech

Model/Description

XP125–12

XP250–12

XP250–24

XP600–12*

XP600–24*

XP1100–12*

XP1100–24*

MSRP

$289.00

$560.00

$560.00

$785.00

$785.00

$935.00

$1,020.00

Voltage

12V

12V

24V

12V

24V

12V

24V

ContinuousPower

125W

250W

250W

600W

600W

1100W

1100W

Dimensions DxWxH

7.90” x 4.93” x 2.16”

12.03” x 5.23” x 2.77”

12.03” x 5.23” x 2.77”

12.10” x 7.70” x 3.60”

12.10” x 7.70” x 3.60”

15.05” x 7.70” x 3.60”

15.05” x 7.70” x 3.60”

Weight

2 lbs

5 lbs

5 lbs

6.5 lbs

6.5 lbs

10 lbs

10 lbs

Surge Power

150W

300W

300W

1100W

1100W

2200W

2200W

TareLoss

5W

5W

6W

8W

8W

20W

20W

* cooling fan

XP Series Inverter

G-12-060C

G-12-250S

G-12-030

INVERTERS

3/03 49

Inverters

Invertek 2500W Inverter

Invertek inverters supply pure sine wave AC output power and are housed in an aluminumchassis for harsh climates. The LED meter displays battery voltage and output watts. The 300 to1500 watt models are transformer based and the 2500 watt is solid state. These inverters areswitch selectable between 50Hz/60Hz and provide overload protection. Built-in RS232 interface forremote control except on the 300 W model. One-year warranty.


DAI-0300L-12-1-A 12 VDC 300W 450W 1W 9.5” x 10.6” x 4.7” 11.02 lbs $230.00



DAI-1500L-12-1-A 12 VDC 1500W 2000W 1W 21” x 10.6” x 4.7” 38.58 lbs $600.00

DAI-1500L-24-1-A 24 VDC 1500W 2000W 1W 21” x 10.6” x 4.7” 38.58 lbs $600.00

DAI-2500H-12-1-A 12 VDC 2500W 3500W 1W 21” x 10.6” x 7.5” 40.98 lbs $1,200.00

DAI-2500H-24-1-A 24 VDC 2500W 3500W 1W 21” x 10.6” x 7.5” 40.98 lbs $1,200.00

Invertek

* tare loss in power save modeInvertek 300W Inverter

SunWize Spotlight

LOCATION:Florence, Alabama

APPLICATION:PV array canopy provides shade for

various activities such as parking,park visitors and sport spectators

SYSTEM:SunWize® PowerPort

30kW Grid Intertie PV System

The system transforms DC power into 480 VAC, 60 Hz, 3-phase utility-grade power. The invertermonitors and matches utility voltage, frequencyand phase angles providing power to the gridduring daylight hours. System capabilitiesinclude fault detection and diagnostics with nooperator intervention.


DC Voltage Continuous Charger AC Volts WeightModel Inverter Input Power Current Output (lbs) MSRP

OBPP-DR1512/S DR1512 12 VDC 1500 W 70 A 120 VAC 160 $2,350.00OBPP-DR1512/D 2 - DR1512 12 VDC 3000 W 70 A x 2 120/240 VAC 200 $3,895.00OBPP-DR1524/S DR1524 24 VDC 1500 W 35 A 120 VAC 160 $2,295.00OBPP-DR1524/D 2 - DR1524 24 VDC 3000 W 35 A x 2 120/240 VAC 200 $3,750.00OBPP-DR2412/S DR2412 12 VDC 2400 W 120 A 120 VAC 170 $2,795.00OBPP-DR2412/D 2 - DR2412 12 VDC 4800 W 120 A x 2 120/240 VAC 220 $4,650.00OBPP-DR2424/S DR2424 24 VDC 2400 W 70 A 120 VAC 165 $2,795.00OBPP-DR2424/D 2 - DR2424 24 VDC 4800 W 70 A x 2 120/240 VAC 205 $4,650.00OBPP-DR3624/S DR3624 24 VDC 3600 W 70 A 120 VAC 170 $2,995.00

Power Centers

INVE

RTER

S

50 3/03

Xantrex Power Panel

Power Panels Power Panels are a packaged power system. They are less expensive than an on-site componentinstallation and meet many power application needs. To install Power Panels, simply connectthem to the battery, PV and or AC loads. Power Panels include inverters and are assembled withcomponents specified by the customer.

Features include:• One or two SW or DR inverters• Powder coated steel back-plate pre-wired

with all NEC/UL requirements, AC & DC overcurrent protection and disconnects: only forindoor installation

• Negative/ground bonding block• Single or dual C40 charge controllers for use

DC charging sources

• Optional nonmetallic battery enclosure whichdoubles as a shipping enclosure

• Flexible conduit for connection of the systemto the battery enclosure

• 60 amp AC system bypass that allowsinverter servicing while keeping AC loadsconnected to the grid or generator

DC Voltage Continuous Charger AC Volts Dimensions LxWxH Weight Model Input Power Current Output (back plate) (lbs) MSRP

PP-SW5548S 48V 5500 W 75 A 120VAC 60 Hz 40” x 43” x 1” 248 $5,695.00PP-SW5548D 48V 11,000 W 75 A x 2 120/240VAC 60Hz 40” x 43” x 1” 396 $9,995.00PP-SW4024S 24V 4000 W 120 A 120VAC 60Hz 40” x 43” x 1” 217 $4,995.00PP-SW4024D 24V 8000 W 120A x 2 120/240VAC 60Hz 40” x 43” x 1” 334 $8,995.00PP-SW4048S 48V 4000 W 60 A 120VAC 60 Hz 40” x 43” x 1” 217 $4,995.00PP-SW4048D 48V 8000 W 60 A x 2 120/240VAC 60 Hz 40” x 43” x 1” 334 $9,137.00PP-DR3624/S 24V 3600 W 70 A 120VAC 60Hz 40” x 43” x 1” 153 $2,529.00PP-DR3624/D 24V 7200 W 70 A x 2 120/240VAC 60Hz 40” x 43” x 1” 206 $4,795.00PP-DR2424/S 24V 2400 W 70 A 120VAC 60Hz 40” x 43” x 1” 148 $2,295.00PP-DR1524/S 24V 1500 W 35 A 120VAC 60Hz 40” x 43” x 1” 139 $1,879.00

OPTIONSPPO-C40 C40 DC charge or load or diversion controller, installed complete with prewired 60 amp DC breaker $258.00PPO-DVM/C40 Accumulating amp hour meter with LCD display, installed on the front of the C40 $99.00PPO-CD15 15 amp DC load breaker, prewired and installed in the DC disconnect $59.00PPO-CD20 20 amp DC load breaker, prewired and installed in the DC disconnect $59.00PPO-CD60 60 amp DC load breaker, prewired and installed in the DC disconnect $59.00

SunWize Power Centers with Xantrex InvertersThese packaged power centers save time, money and space by combining DC disconnects, ACbypass breakers, overcurrent protection devices, grounding components and inverters on aneasy to install panel. Simply connect the power panel to the battery, PV and/or AC loads.SunWize assembled power centers are easily modified and expanded as your system grows orchanges. Dimensions are 36” x 50”; with charge controller option, 36” x 55”. ETL listed.

SunWize®

SunWize Power Center

(continued)

Xantrex




OBPP-DR1512/S DR1512 12 VDC 1500 W 70 A 120 VAC 160 $2,350.00OBPP-DR1512/D 2 - DR1512 12 VDC 3000 W 70 A x 2 120/240 VAC 200 $3,895.00OBPP-DR1524/S DR1524 24 VDC 1500 W 35 A 120 VAC 160 $2,295.00OBPP-DR1524/D 2 - DR1524 24 VDC 3000 W 35 A x 2 120/240 VAC 200 $3,750.00OBPP-DR2412/S DR2412 12 VDC 2400 W 120 A 120 VAC 170 $2,795.00OBPP-DR2412/D 2 - DR2412 12 VDC 4800 W 120 A x 2 120/240 VAC 220 $4,650.00OBPP-DR2424/S DR2424 24 VDC 2400 W 70 A 120 VAC 165 $2,795.00OBPP-DR2424/D 2 - DR2424 24 VDC 4800 W 70 A x 2 120/240 VAC 205 $4,650.00OBPP-DR3624/S DR3624 24 VDC 3600 W 70 A 120 VAC 170 $2,995.00

Power Centers

INVE

RTER

S

3/03

Xantrex Power Panel

Power Panels Power Panels are a packaged power system. They are less expensive than an on-site componentinstallation and meet many power application needs. To install Power Panels, simply connectthem to the battery, PV and or AC loads. Power Panels include inverters and are assembled withcomponents specified by the customer.

Features include:• One or two SW or DR inverters• Powder coated steel back-plate pre-wired

with all NEC/UL requirements, AC & DC overcurrent protection and disconnects: only forindoor installation

• Negative/ground bonding block• Single or dual C40 charge controllers for use

DC charging sources

• Optional nonmetallic battery enclosure whichdoubles as a shipping enclosure

• Flexible conduit for connection of the systemto the battery enclosure

• 60 amp AC system bypass that allowsinverter servicing while keeping AC loadsconnected to the grid or generator

DC Voltage Continuous Charger AC Volts Dimensions LxWxH Weight Model Input Power Current Output (back plate) (lbs) MSRP

PP-SW5548S 48V 5500 W 75 A 120VAC 60 Hz 40” x 43” x 1” 248 $5,695.00PP-SW5548D 48V 11,000 W 75 A x 2 120/240VAC 60Hz 40” x 43” x 1” 396 $9,995.00PP-SW4024S 24V 4000 W 120 A 120VAC 60Hz 40” x 43” x 1” 217 $4,995.00PP-SW4024D 24V 8000 W 120A x 2 120/240VAC 60Hz 40” x 43” x 1” 334 $8,995.00PP-SW4048S 48V 4000 W 60 A 120VAC 60 Hz 40” x 43” x 1” 217 $4,995.00PP-SW4048D 48V 8000 W 60 A x 2 120/240VAC 60 Hz 40” x 43” x 1” 334 $9,137.00PP-DR3624/S 24V 3600 W 70 A 120VAC 60Hz 40” x 43” x 1” 153 $2,529.00PP-DR3624/D 24V 7200 W 70 A x 2 120/240VAC 60Hz 40” x 43” x 1” 206 $4,795.00PP-DR2424/S 24V 2400 W 70 A 120VAC 60Hz 40” x 43” x 1” 148 $2,295.00PP-DR1524/S 24V 1500 W 35 A 120VAC 60Hz 40” x 43” x 1” 139 $1,879.00

OPTIONSPPO-C40 C40 DC charge or load or diversion controller, installed complete with prewired 60 amp DC breaker $258.00PPO-DVM/C40 Accumulating amp hour meter with LCD display, installed on the front of the C40 $99.00PPO-CD15 15 amp DC load breaker, prewired and installed in the DC disconnect $59.00PPO-CD20 20 amp DC load breaker, prewired and installed in the DC disconnect $59.00PPO-CD60 60 amp DC load breaker, prewired and installed in the DC disconnect $59.00

SunWize Power Centers with Xantrex InvertersThese packaged power centers save time, money and space by combining DC disconnects, ACbypass breakers, overcurrent protection devices, grounding components and inverters on aneasy to install panel. Simply connect the power panel to the battery, PV and/or AC loads.SunWize assembled power centers are easily modified and expanded as your system grows orchanges. Dimensions are 36” x 50”; with charge controller option, 36” x 55”. ETL listed.

SunWize®

SunWize Power Center

(continued)

Xantrex

INVERTERS

3/03

Power Centers

SunWize Power Centers with Xantrex Inverters


OBPP-DR3624/D 2 - DR3624 24 VDC` 7200 W 70 A x 2 120/240 VAC 220 $5,095.00OBPP-SW4024/S SW4024 24 VDC 4000 W 120 A 120 VAC 235 $4,950.00OBPP-SW4024/D 2 - SW4024 24 VDC 8000 W 120 A x 2 120/240 VAC 336 $8,950.00OBPP- SW4048/S SW4048 48 VDC 4000 W 60 A 120 VAC 235 $4,950.00OBPP-SW4048/D 2- SW4048 48 VDC 8000 W 60 A x 2 120/240 VAC 336 $8,950.00OBPP-SW5548/S SW5548 48 VDC 5500 W 75 A 120 VAC 262 $5,550.00OBPP-SW5548/D 2- SW5548 48 VDC 11,000 W 75 A x 2 120/240 VAC 378 $9,950.00

SunWize Power Centers with OutBack Inverters


OBPP-FX2024-1 FX2024 24 VDC 2000 W 55 A 120 VAC 186 $3325.00OBPP-FX2024-2 2 - FX2024 24 VDC 4000 W 55 A x 2 120/240 VAC 256 $5650.00OBPP-FX2024-3 3 - FX2024 24 VDC 6000 W 55 A x 3 120/240 VAC 326 $7925.00OBPP-FX2024-4 4 - FX2024 24 VDC 8000 W 55 A x 4 120/240 VAC 396 $10,175.00OBPP-FX2548-1 FX2548 48 VDC 2500 W 30 A 120 VAC 186 $3775.00OBPP-FX2548-2 2 - FX2548 48 VDC 5000 W 30 A x 2 120/240 VAC 256 $6550.00OBPP-FX2548-3 3 - FX2548 48 VDC 7500 W 30 A x 3 120/240 VAC 326 $9275.00OBPP-FX2548-4 4 - FX2548 48 VDC 10,000 W 30 A x 4 120/240 VAC 396 $11,975.00

Installed Options for SunWize Power Centers


1X-C40 One C-40, 40 Amp charge controller $299.00

2X-C40 Two C-40, 40 Amp charge controllers $559.003X-C40 Three C-40, 40 Amp charge controllers $819.001X-C60 One C-60, 60 Amp charge controller $349.002X-C60 Two C-60, 60 Amp charge controllers $649.003X-C60 Three C-60, 60 Amp charge controllers $959.00Dig Meter C40/60 CM digital meter -one needed per controller $129.001 X MX60 One MX60 controller $839.002 X MX60 Two MX60 controllers $1449.00100A-DC Bkr 100 Amp DC Breaker $65.0060A-DC Bkr 60 Amp DC Breaker $52.0040A-DC Bkr 40 Amp DC Breaker $52.0030A-DC Bkr 30 Amp DC Breaker $41.0015A-DC Bkr 15 Amp DC Breaker $41.0060A-120VAC Bkr 60 Amp, 120VAC breaker $27.0060A-240VAC Bkr 60 Amp, 240VAC breaker $45.0030A-120VAC Bkr 30 Amp, 120VAC breaker $27.0030A-240VAC Bkr 30 Amp, 240VAC breaker $43.0025A-240VAC Bkr 25 Amp, 240VAC breaker $54.0020A-120VAC Bkr 20 Amp, 120VAC breaker $27.0015A-120VAC Bkr 15 Amp, 120VAC breaker $25.00GGB Ground Bus Bar $25.00TBB Terminal Bus Bar $29.00Link 10 Link 10 System Meter $299.00PVGFP-2 Ground Fault Protection $179.00X-240 Auto Transformer $419.00X-Fan Transformer Fan Kit $52.00RVPP Kit Installation kit for RV Power controller, controller sold separately $55.00SW-GTI Xantrex grid tied interface kit $599.00

(continued)



Inverters

PROwatt Mid to High Powered InvertersThese PROwatt inverters are designed to operate a wide range of applications includinghousehold products, recreational, large single loads, and high power industrial. All modelsprovide standard protection. The PROwatt 800 to 1500 models feature a dual GFCI outlet,addition of external AC outlets, a built-in LED display for volts and amps, and a remote on/offswitch. The PROwatt 1750 and 3000 models include heavy-duty terminals for trouble-freebattery connection. One-year warranty.

Xantrex AccessoriesIN

VERT

ERS

3/03

Autotransformer or Balancing TransformerIncludes built-in dual pole 25 amp circuit breaker disconnect. Rated for 3900 watts continuousoutput. UL listed.

T240 120-240 volt step-up or step-down transformer,maximum continuous power 3.9kVA $350.00

Battery Temperature SensorsBTS/15 Battery temperature sensor with 15’ cable for

DR, SW, PS and UX series $29.00

BTS/35 Battery temperature sensor with 35’ cable for DR, SW, PS and UX series $32.00

Remote ControlsRC8/50 Remote on/off control with status LED indicator

for all DR, PS, TS and UX series with 50’ cable $69.00

RC8/100 Remote on/off control with status LED indicator for all DR, PS, TS and UX series with 100’ cable $94.00

Ground Fault ProtectionGround fault protection is required for residential PV rooftop installations on homes in the US. UL listed. Does not include an enclosure. 100 amp DC max per pole.

PVGFP1 Ground fault protection, one pole for one solar array $275.00

PVGFP2 Ground fault protection, two pole for two solar sub-arrays $325.00

PVGFP3 Ground fault protection, three pole for three solar sub-arrays $375.00

PVGFP4 Ground fault protection, four pole for four solar sub-arrays $425.00

T240 Autotransformer

Battery Temperature Sensor

RC8 Remote Control

PVGFP1 Ground Fault Protection

Xantrex

PROwatt 3000 Inverter


PROwatt 600 90% 12 V 600 W 1200 W 115 VAC 2.5” x 6.25” x 11” 4.1 lbs $130.00





PROwatt 3000 90% 12 V 2500 W 5000 W 115 VAC 6.25” x 8” x 18.5” 20.0 lbs $800.00

ELEC

TRIC

AL/

HARD

WAR

E

3/03

Electrical/Wire & Cable

SunWize USE-2 Wire

Service Entrance, USE-2, or RHH/RHW-2General purpose wiring, suitable for power and control circuits in residential and commercialbuildings, industrial plants, meters and utility substations. Suitable for outdoor, raceway or directburial use. Single conductor 7-strand copper with XLP insulation. Rated 600 volts, 90˚C wet/dry.Minimum order 100 ft.

AWG / Color O.D. Weight (lbs/1000ft) Ampacity (75˚C) MSRP

#12USE Red 0.19” 31 30A $0.26 per ft.

#12USE Black 0.19” 31 30A $0.26 per ft.

#10USE Red 0.21” 45 40A $0.43 per ft.

#10USE Black 0.21” 45 40A $0.43 per ft.

#10USE White 0.21” 45 40A $0.43 per ft.

#10USE Green 0.21” 45 40A $0.43 per ft.

#8USE Red 0.27” 72 55A $0.60 per ft.

#8USE Black 0.27” 72 55A $0.60 per ft.

#6USE Red 0.31” 107 75A $0.95 per ft.

#6USE Black 0.31” 107 75A $0.95 per ft.

#4USE Red 0.36” 161 95A $1.25 per ft.

#4USE Black 0.36” 161 95A $1.25 per ft.

#2USE Black 0.42” 244 130A $1.35 per ft.

Tray CableDesigned for power & control, traffic control, switching, lighting and signal transmission. May beused in Class 1, Div. 2 locations. Stranded copper conductors are THHN insulated with overallblack PVC jacket. UL listed, sunlight resistant, direct burial or cable trays, 90˚C, 600 volts. Twoconductor cables are red/black, oval construction, #8 & #6 AWG cables are round. Minimumorder 100 ft.

AWG / Conductor O.D. Weight (lbs/1000ft) Ampacity MSRP

#18/2 TC 0.18” x 0.28” 41 14A $0.27 per ft.#16/2 TC 0.20” x 0.33” 49 18A $0.29 per ft.#14/2 TC 0.21” x 0.32” 64 25A $0.39 per ft.#12/2 TC 0.23” x 0.36” 83 30A $0.43 per ft.#10/2 TC 0.26” x 0.43” 120 40A $0.59 per ft.#8/2 TC 0.56” O.D. 220 55A $1.23 per ft.#6/2 TC 0.63” O.D. 310 75A $2.64 per ft.

SunWize Tray Cable

THHN/THWNGeneral purpose wiring, suitable for lighting and power in new or existing construction in residential, commercial and industrialsystems. Also used for power control circuits and relay panels. Single conductor, 19-strand copper with PVC insulationsheathed with nylon for easy pulling in conduits. Resistant to chemicals, oils, gasoline and flame. Rated 600 volts, 90˚C wet,75˚C dry. Sold by the foot.

AWG / Color O.D. Weight (lbs/1000ft) Ampacity (75˚C) MSRP#12THHN Red 0.14” 25 25A $0.17 per ft.#12THHN Black 0.14” 25 25A $0.17 per ft.#12THHN White 0.14” 25 25A $0.17 per ft.#12THHN Green 0.14” 25 25A $0.17 per ft.#10THHN Red 0.17” 39 35A $0.17 per ft.#10THHN Black 0.17” 39 35A $0.17 per ft.#10THHN White 0.17” 39 35A $0.17 per ft.#10THHN Green 0.17” 39 35A $0.17 per ft.#6THHN Red 0.25” 98 65A $0.50 per ft.#6THHN Black 0.25” 98 65A $0.50 per ft.#6THHN White 0.25” 98 65A $0.50 per ft.#6THHN Green 0.25” 98 65A $0.50 per ft.#4THHN Red 0.36” 115 85A $0.70 per ft.#4THHN Black 0.36” 115 85A $0.70 per ft.#4THHN White 0.36” 115 85A $0.70 per ft.


ELECTRICAL/HARDW

ARE

3/03


Pump Cable-SubmersibleFor use with submersible pumps in power and control circuits, stranded copper conductors withEPR insulation, color-coded red/black/yellow and overall PVC jacket. Flat construction, rated90˚C, 600 volts. (W/G = with ground).

AWG Flat Construction Weight-lbs/1000ft. MSRP

#10/2 SUB 0.56” x 0.31” 180 $1.10 per ft.#10/2 SUB W/Gnd 0.63” x 0.31” 232 $1.20 per ft.#10/3 SUB W/Gnd 0.75” x 0.31” 300 $1.32 per ft.#8/2 SUB W/Gnd 0.88” x 0.38” 346 $2.10 per ft.#8/3 SUB W/Gnd 1.00” x 0.38” 450 $2.35 per ft.#6/3 SUB W/Gnd 1.12” x 0.38” 580 $2.92 per ft.

Battery Cable – ULIntended for internal wiring of appliances as machine tool wire. Recommended for hard serviceuse. Suitable for connecting to battery or inverter systems. CSA type AWM/TEW, 105˚C, UL listedtype MTW 90˚C, 600 volts, single conductor stranded copper with black PVC insulation. Minimumorder 100 ft.

AWG O.D. Weight (lbs/1000ft) Stranding MSRP

2/0 0.58” 496 1320 x 0.010 $4.70 per ft.4/0 0.69” 760 2090 x 0.010 $6.50 per ft.

Module Ground Kit

For solar module frame ground connections. Includes 30” - #10AWG copper braid & fasteners.

Model MSRP

MODGNDKIT $13.00

Splice Kits – Pump Cable Waterproof heat shrink kit includes copper, crimp type, brazed-seam butt connectors, 3/8”conductor insulation shrink tubing and overall 1” cable jacket heat shrinkable tubing. Bothtubings have inner melt wall adhesive.

Model # Conductors x AWG MSRP

SPLK-14 2 X #14 $14.00SPLK-10 3 x #10 $18.00SPLK-8 4 x #8 $24.00SPLK-6 4 x #6 $28.00

SunWize Pump Cable

SunWize Battery Cable

SunWize Splice Kit

Ground WireBare-twisted, 7-strand medium hard drawn copper wire used for grounding connections.Minimum order 100 ft.

AWG O.D. Weight (lbs/1000ft) MSRP

#8 Bare 0.15” 51 $0.29 per ft.#6 Bare 0.19” 81 $0.35 per ft.#4 Bare 0.23” 129 $0.99 per ft.#2 Bare 0.29” 205 $1.25 per ft.

Grounding Rod Kit The grounding kit includes 5/8” x 8’ copper clad steel ground rod, acorn fitting, coupling and #2copper lug.

Item MSRP

Grounding Kit $49.00

SunWize Ground Wire


ELEC

TRIC

AL/

HARD

WAR

E

3/03

Butt ConnectorsCopper, crimp type butt connectors are useful for in-line cable splice. Non insulated brazed-seambarrel can be soldered.

Model Wire Size AWG Length MSRP

32260 12-10 7/8” $0.2533060 8 1” $0.5034060 6 1” $1.0035060 4 1-1/8” $1.00

Cord ConnectorsWeather-resistant, liquid-tight cable strain relief fittings are black nylon with flexible rubberbushing that allows for flat or round cables. Used for cable entry connection to junction boxes orenclosures. Without locknuts.

Size Cable Diameter MSRP

1/2NPT 0.23” - 0.55” $1.751/2NPT 0.50” - 0.75” $10.753/4NPT 0.19” - 0.40” $12.003/4NPT 0.45” - 0.70” $2.99

Conduit – Flexible

Liquid tight non-metallic flexible PVC conduit is UL listed for outdoor use in temperatures of 80˚C.

NPT size Weight (lbs/1000ft) MSRP

1/2” 13.3 $1.25 per ft.1” 25.9 $2.25 per ft.2” 61.7 $4.50 per ft.

Conduit FittingsLiquid-tight PVC fittings for flexible, non-metallic conduit allow fast and easy installation. Includelocking nut and sealing ring.

Straight FittingsNPT Size MSRP

1/2” $2.751” $6.502” $19.50

90 Degree FittingsNPT Size MSRP

1/2” $4.001” $25.002” $55.00

Cable TiesAdd a professional look to any wiring job with black nylon, heavy-duty cable ties rated foroutdoor use that are sunlight–resistant. Sold in packs of 100 each.

Length MSRP

4” $22.005.5” $23.0011.5” $29.00

Cable Tie Mount MSRP

1” square with adhesive back $0.75


Fittings

Butt Connectors

Cord Connectors

Flexible Conduit

Straight Conduit Fitting

90º Conduit Fitting

Cable Ties



ELECTRICAL/HARDW

ARE

3/03

Electrical/Wire & Cable Pump Cable-SubmersibleFor use with submersible pumps in power and control circuits, stranded copper conductors withEPR insulation, color-coded red/black/yellow and overall PVC jacket. Flat construction, rated90˚C, 600 volts. (W/G = with ground).

AWG Flat Construction Weight-lbs/1000ft. MSRP

#10/2 SUB 0.56” x 0.31” 180 $1.10 per ft.#10/2 SUB W/Gnd 0.63” x 0.31” 232 $1.20 per ft.#10/3 SUB W/Gnd 0.75” x 0.31” 300 $1.32 per ft.#8/2 SUB W/Gnd 0.88” x 0.38” 346 $2.10 per ft.#8/3 SUB W/Gnd 1.00” x 0.38” 450 $2.35 per ft.#6/3 SUB W/Gnd 1.12” x 0.38” 580 $2.92 per ft.

Battery Cable – ULIntended for internal wiring of appliances as machine tool wire. Recommended for hard serviceuse. Suitable for connecting to battery or inverter systems. CSA type AWM/TEW, 105˚C, UL listedtype MTW 90˚C, 600 volts, single conductor stranded copper with black PVC insulation. Minimumorder 100 ft.

AWG O.D. Weight (lbs/1000ft) Stranding MSRP

2/0 0.58” 496 1320 x 0.010 $4.70 per ft.4/0 0.69” 760 2090 x 0.010 $6.50 per ft.

Module Ground Kit

For solar module frame ground connections. Includes 30” - #10AWG copper braid & fasteners.

Model MSRP

MODGNDKIT $13.00

Splice Kits – Pump Cable Waterproof heat shrink kit includes copper, crimp type, brazed-seam butt connectors, 3/8”conductor insulation shrink tubing and overall 1” cable jacket heat shrinkable tubing. Bothtubings have inner melt wall adhesive.

Model # Conductors x AWG MSRP

SPLK-14 2 X #14 $14.00SPLK-10 3 x #10 $18.00SPLK-8 4 x #8 $24.00SPLK-6 4 x #6 $28.00

SunWize Pump Cable

SunWize Battery Cable

SunWize Splice Kit

FittingsRing Tongue Wire TerminalsCrimp-on terminals are manufactured of the finest electrolytic copper and are tin-plated for corrosion-resistance. Molded nylon insulation over butted seam barrel and brass sleeve over the barrel.

AWG Screw Size MSRP

#10-12 # 10 $0.29#10-12 1/4” $0.29#10-12 5/16” $0.40#10-12 3/8” $0.45

Copper Lugs Compression-type, flared entry, single hole, copper lug used for connection on battery cable.

Model AWG x Bolt size MSRPCL-4 #4 AWG x 1/4” $4.30CL-2/0 #2/0 AWG x 3/8” $4.30CL-4/0 #4/0 AWG x 3/8” $4.30

Ring Tongue Terminals

Copper Lugs

ELECTRICAL/HARDW

ARE

3/03


Barrier Terminal BlockBarrier screw terminal blocks are isolated double row 6 positions with nickel-plated brass busmaterial. Closed back insulates power from mounting surface, add jumpers for common circuits.

Model Current Rating Max Voltage Screw Size Dimensions Weight (lbs) MSRP

47106 20A 150 #6 7/8” X 2-7/8” 0.08 $4.0047356 30A 600 #8 1-5/16” X 4-3/8”” 0.21 $7.00

Euro-Style Terminal BlockEuro-Style terminal blocks feature a finger-safe screw terminal design and are rated 600VAC/DC.The nylon body meets insulating requirements without use of an external cover. Dual row screwand pressure plate combination accepts stripped wire without need for crimp-on terminals. Amounting hole is located between each terminal post, supplied in 12 positions and is easily cutfor fewer connections.

Model Wire Range Mtg. Screw Size Current Rating Dimensions Weight (lbs) MSRP

2812 #12-18 #4 27A 0.80” x 4.61” 0.12 $7.502912 #8-14 #6 45A 0.90” X 5.50” 0.25 $9.50

Dead Front Terminal BlockThis heavy-duty black molded phenolic, dual row terminal block features a finger-safe designwith tin plated brass pressure screw connections into an aluminum barrel. Supplied threeposition only. UL rated 600VAC/DC.

Model Wire Size Mtg Screw Size Max Current Rating Dimensions Weight (lbs) MSRP

9-85-3 #4-14 AWG #8 85 A 1.25” x 1.80” .027 $16.00

Power Post Cable ConnectorSturdy glass reinforced nylon base supports a 1” tall stainless steel 5/16”-18 stud. Connects highamperage cables securely to common post. Can stack multiple terminals. Rated 48VDC.

Model Size Mtg. Screw Size MSRP

2002 1.75” x 3.0” 1/4” $12.50

Power Distribution Terminal BlockThis terminal block allows a main conductor to be tapped with multiple conductors, useful forcombining circuits. Set screw-type, aluminum lug mounted into an insulating phenolic holder.

Model AWG main (qty) AWG tap Dimensions Weight (lbs) MSRP

PDB1-1 #2/0-14 (1) #2/0-14 (1) 1.0” X 2.88” 0.25 $17.00PDB1-4 #2/0-14 (1) #8-14 (4) 1.0” X 2.88” 0.25 $19.00PDB1-6 #2/0-12 (1) #4-14 (6) 1.75” X 4.00” 1.25 $60.00

Common Bus Bar TerminalThe stud type, 4 position terminal design allows for common bus connections of positive or negativeDC circuits, rated for 48VDC. Tin plated copper bus bar is mounted to an isolated phenolic basewith recessed #10 mounting screw holes. Stainless steel studs allow high torque connections.

Model Current Rating Stud Size Dimensions Weight (lbs) MSRP

2305 100A #10 0.88” x 4.20” 0.15 $9.002303 150A 1/4” 1.25” X 6.10” 0.34 $14.002106 250A 5/16” 1.50” X 7.9” 0.60 $29.002104 600A 3/8” 2.00” X 7.00” 1.71 $69.00

Terminal Blocks

Barrier Terminal Block

Euro-Style Terminal Block

Dead Front Terminal Block

Common Bus Bar Terminal

Power Distribution Block

Power Post Cable Connector


ELEC

TRIC

AL/

HARD

WAR

E

3/03

Wire & Cable

When additional wiring is needed, refer to the following charts to determine correct sizing. Selecting the correct size andtype of wire will enhance the performance and reliability of your PV system. The size of the wire must be large enough tocarry the maximum current expected without undue voltage losses. All wire has a certain amount of resistance to the flowof current. This resistance causes a drop in the voltage from the source to the load. Voltage drops cause inefficiencies,especially in low voltage systems (12V or less). There are several different types of wire available depending on how andwhere it will be used. For example, there are wire types designed for resistance to sunlight exposure, high temperaturesand direct burial. Specify wiring that will withstand the worst conditions.The wire sizing guide below provides the minimum wire size needed to limit voltage drops to 5% at a given distance in a12V or 24V system. If you want to limit your losses to 2%, simply divide the distance by 2.5. For a 48V system, multiply thedistance taken from the 24V chart by 2. The dashes represent currents which cannot be handled by the wire size.

Wiring Reference Guide

How charts work1. — On the left, locate the current you will be dealing with (either array or load current.) 2. — Move across to locatedistance to be traveled. 3. — Move up to locate size of wire to be used.

Amps12468101520253035404550

1410653271813117–––––––

121698542282117118––––––

10269134674534271813119––––

84272141077153432821171412–––

667934017011385684534272319171514

410805402701801351087254433631272422

2171785942928621517211486695749433834

121661083542361271217144108877262544843

0273013656824553412731821361099178686155

003444172286157443034423017213811598867769

0004342217110867245434342892171741451241099687

0000547527381369913684548365274219183156137122110

Maximum one-way distance (feet) for 5% voltage loss in 12 volt systems. Wire Size (AWG)

Wire Sizing Chart 12 Volt System

Amps12468101520253035404550

142131065335272114–––––––

12338169855642342317––––––

1053726913490675436272118––––

8854427214142107855743342824–––

613596793402261701369168544539343027

421601080540360270216144108867262544843

23434171785957242934322917213711498867669

14332216610837225424332892171731441241089687

0546027301365910682546364273218182156136121109

006887344417221148861689459344275230197172153138

00086844342217114471086868579434347289248217193174

00001095154752738182513691095730548438365313274243219

Maximum one-way distance (feet) for 5% voltage loss in 24 volt systems. Wire Size (AWG)

Wire Sizing Chart 24 Volt System


ELECTRICAL/HARDW

ARE

3/03

Hardware

Hardware Kits Fasteners are type 316 fully threaded, stainless steel, hex head bolts including flat and lockwashers and full hex nuts. All are packaged in bag kits with the quantity of bolts noted.

Model Description Bolt Size Bolt Qty Weight (lbs) MSRP

HK-1/4” Module 1/4”-20 x 3/4” 4 0.13 $2.00Hardware Kit (4 pk)

HK-3/8” Medium 3/8”-16 x 1” 8 0.77 $6.50Hardware Kit (8 pk)

HK-1/2” Large 1/2”-13 x 1.5” 8 1.70 $14.50Hardware Kit (8 pk)

Security Hardware KitsTamperproof fasteners are 18-8 stainless steel and employ a special head design requiring aspecial tool. Button head screws are pin-in hex drive and cannot be removed with conventionaltools. Each bolt includes flat washers and a nylon-locking hex nut requiring two tools for assembly.

Model Description Bolt Size Bolt Qty Weight (lbs) MSRP

SHK-1/4” Module Security 1/4”-20 x 3/4” 4 0.15 $3.50Hardware Kit (4 pk)

SHK-3/8” Medium Security 3/8”-16 x 1” 8 0.80 $15.00Hardware Kit (8 pk)

Security Hardware ToolsHardened steel 1/4” hex bits for cordless drills and hand drivers or ‘L’ keys for tight locations,both for pin-in-hex drive screws.

Model/Hex Size Screw Size MSRP

Hex bit-5/32” 1/4” -20 $5.00 Hex bit-7/32” 3/8”-16 $5.00‘L’ key-5/32” 1/4”-20 $5.00 ‘L’ key-7/32” 3/8”-16 $5.00

Wall Anchor KitsPatented hollow-wall anchor design features a steel (machine screw size) anchoring channelattached to adjustable ‘zip’ legs providing one-way installation into wall/roof thickness from 3/8”to 2-1/2”. Stay-in-place anchor will not fall out when screw is removed. Perfect for attachingsolar module racks to roofs or heavy equipment enclosures on interior walls. Kits include screws.

Model Screw Size Kit Qty Drywall Pull- Pilot HoleOut Strength MSRP

BA3/16-24 #10-24 x 2” 4 306 lbs 1/2” $0.99BB1/4-20 1/4”-20 x 2” 4 356 lbs 1/2” $0.99BC3/8-16 3/8”-16 x 2” 4 576 lbs 9/16” $1.99

U-Bolts3/8”-16 stainless steel U-bolts are packaged in pairs including hex nuts, flat and lock washers.

Model/ Width Bolt Length WeightNom. Pipe Size Between Legs (lbs) MSRP

U Bolt 1-1/2” 2.0” 2.63” 0.40 $12.50U Bolt 2” 2.5” 3.12” 0.50 $13.50U Bolt 2-1/2” 3.0” 3.63” 0.60 $14.00U Bolt 3” 3.5” 4.12” 0.80 $17.25U Bolt 3-1/2” 4.0” 5.12” 0.90 $20.00U Bolt 4” 4.5” 6.0” 1.20 $21.00


ELEC

TRIC

AL/

HARD

WAR

E

3/03

Hardware

Square Bolts 5”304 stainless steel square bolt is used mostly for enclosure attachment to 5” square lighting poles.

Model Length Thread Size Weight (lbs) MSRP 5” Square Bolt 6” 3/8”-16 1.0 $21.506” Square Bolt 7” 1/2” -13 1.0 $34.50

Band Clamps-AdjustableStainless steel band clamps are 9/16” wide and feature a self-locking, adjustable worm drive screw.

Model Clamp Range Diameter MSRPBand Clamp Small 1.8” to 2.8” $3.00Band Clamp Medium 1.8” to 5.0” $4.50Band Clamp Large 3.1” to 6.0” $5.00

Pipe ClampsTwo piece, electro-galvanized, steel clamps are used for strong attachments of the strut channelto poles.

Model/Nominal WeightPipe Size Design Load Gauge (lbs) MSRPPipe Clamp 2” 800 lbs 12 0.34 $4.50Pipe Clamp 2.5” 800 lbs 12 0.40 $4.75Pipe Clamp 3” 800 lbs 12 0.47 $5.00Pipe Clamp 3.5” 1000 lbs 11 0.62 $5.50Pipe Clamp 4” 1000 lbs 11 0.67 $5.75Pipe Clamp 6” 1000 lbs 10 1.0 $11.50

Strut Channel-AluminumExtruded 1.63” sq. x 0.105” wall, 40” long aluminum strut channel can easily be cut and fits alltypes of strut clamps & nuts.

Model Size Weight (lbs) MSRPStrut Channel 1.63” sq. x 40” long 2.20 $22.00

Channel NutsElectro-galvanized steel nuts for 1-5/8” channels lock in place when fastened to strut-channel.

Model Machine Screw Size Weight (lbs) MSRPChannel Nut 1/4” 1/4”-20UNC 0.07 $0.75Channel Nut 3/8” 3/8”-16UNC 0.09 $1.25Channel Nut 1/2” 1/2”-13UNC 0.12 $2.00

Mini-LouversMini-louvers relieve heat build-up in enclosures. Round aluminum vents are rainproof and keepout insects.

Model Color MSRPMini- Louver 2” diameter silver $3.50Mini-Louver 4” diameter black $7.50


ELECTRICAL/HARDW

ARE

Hardware

Vent Fan-DCBrushless, DC tube axial fan can be used in a variety of applications operating directly from asolar module or battery. It can also be controlled to vent heat or fumes from equipment/batteryenclosures or outbuildings.

Model Power RPM-Max Air Flow Size Weight (lbs) MSRPVent Fan 4.8 W 2800 40cfm @12V 4.76” sq. X 1” D 1.0 lbs $28.0024VDC or 80cfm @ 24VDCFan Guard – Chrome $3.00

Power Vent FanCommonly used to vent battery enclosures to outside air, this one-piece unit fits onto PVC pipe,1.5” = 3cfm, or 2” = 6cfm. Includes back draft damper. When used with the control relays on theSW inverter, the fan can be programmed to operate only when flooded batteries are gassing.Power consumption = 2.2 watts.

Model/Voltage MSRP

Power Vent Fan 12V $135.00Power Vent Fan 24V $135.00Power Vent Fan 48V $215.00

Hole Plugs- Enclosure Rubber plugs form a liquid tight seal and fit standard NPT knockout sizes. For outdoor use.

Model/NPT Size MSRP

Hole Plug 1/2” $1.00Hole Plug 3/4” $1.75Hole Plug 1” $2.25

Sealing WashersHelps seal fastener penetrations in enclosures, neoprene bonded to stainless steel flat washer.

Model/Screw Size O.D. MSRP

#10 1/2” $0.30

1/4” 5/8” $0.50

3/8” 1” $0.60

SunWize Spotlight

LOCATION:Northern Arizona

APPLICATION:Remote home power

SYSTEM:SunWize® 880W PV

Hybrid Power Station

3/03 81


SunWize Systems

The Solar Connect Program

SunWize, a national solar energy company, developed the Solar Connect program to

offer homeowners reliable grid-tied solar systems installed by qualified solar energy

experts. Solar Connect installers provide after sales service and system warranties.

They also help you utilize your State’s

incentives and net metering programs to

provide the most cost-effective system

for your needs. Visit www.dsireusa.org

for information about your State’s incentives and

Federal tax credits for residential solar systems.

Why Consider Solar for Your Home?

Using solar for all or part of your home’s

electrical needs makes sense. Utility tied solar

electric systems are less expensive than ever

and can reduce the amount of electricity you

purchase from your local utility. You may be able

to sell excess electricity to your utility where net

metering programs are available. You will be

producing reliable, clean power that reduces the

burning of fossil fuels to contribute to a healthier

environment. Solar electric systems are quiet,

operate automatically, require very little

maintenance and need no fuel except sunshine!

Solar Connect Grid-Tied Systems

Solar Connect systems include UL listed equipment to provide utility quality power. Installations

meet National Electric Code requirements for years of safe, reliable electric generation. Systems

are available in a variety of models – your Solar Connect Installer will help you choose the right

system for your home. Solar Connect Installers can also provide battery backup in the event of

power outages.

It’s Easy to Get Started:

1. Contact SunWize for a list of qualified Solar

Connect Installers by calling 800-817-6527 or

send an email to [email protected].

2. Contact your Solar Connect Installer to

choose a system and schedule installation.

Solar Connect®

SUNW

IZE

SYST

EMS

3/03

Solar modules produce DC electricity when exposedto sunlight. The electricity is converted to householdAC by an inverter and is fed into the home’selectrical load center. When excess electricity isproduced, the meter runs backwards as theelectricity goes out to the utility line. Each systemincludes solar modules. module mounts, an inverter,cable, all necessary mounting hardware andelectrical components.

Solar Connect kWhr Meter

Utility Approved Inverter

AC Disconnect Switch

DC Disconnect Switch

Typical Solar Connect Configuration

Solar ConnectBenefits:

• Reliable systems add value to your home

• UL listed components

• Qualified installers

• After sales servicecontracts & warranties

• Many systems availableto fit your power needs

• Relax & enjoy generatingyour own clean energy

DC and AC Surge Protection

Re

sid

ential syste

ms b

y B

uilt

We

ll, N

o.

Be

llmo

re,

NY


SUNWIZE

SYSTEMS

3/03

SunWize Systems

The Sanyo HIT module is usedin the SunWize ResidentialGrid-Tie Systems

SunWize Residential Grid-Tie Systems provide reliable power for your homeusing top quality UL listed products. Each system is pre-packaged to savedesign time and includes Sanyo solar modules, UniRac SolarMountmounting kits, Sunny Boy inverters, cables and all necessary hardware andelectrical components. SunWize grid tie systems are modular which meansyou can combine multiple units together or add to your system in the future.

Sanyo solar modules are ideal for grid-tie applications. Unlike othermodules that include a guarantee of plus or minus 10% of their ratedoutput, Sanyo offers a unique guarantee that their modules never produceless than the rated power output. Sanyo modules also outperform all othermodules due to the fact that they maintain higher voltages at highertemperatures - which means more power and better performance. The

result is one of the highest Performance Test Condition ratings per watt (W ptc) for higherrebates in California. Performance Test Condition testing simulates the real world, high celltemperature modules are subjected to in the field.

SunWize grid tie systems are easily installed on the roof of any building. An entire array can befully installed and wired on the roof one module at a time. The mounts securely attach the arrayto the roof in compliance with USBuilding Codes. All systems meetNEC code requirements and USsafety standards. Completeinstallation guide and operationalmanual included. 20-yearwarranty on power output and afive-year system warranty. Anoptional utility grade kWh meter isavailable – see page 31.

This product qualifies for theSunWize Solar Connect® Programthat offers homeowners reliablesystems installed by qualifiedsolar energy experts. Ask yourdealer for more information.

Features:* Array DC disconnect* Lightning surge arrestors* Inverter fused AC disconnect* MultiContact™ #10AWG wiring array to panel J-box * Complete PV array grounding system

Residential Grid-Tie Systems

Model # Modules Rated Power PTC Rating Array Open Array Rated Short Circuit Rated Current Inverter(Watts) (Watts) Circuit (Voc) Voltage (Vmp) Current (Isc) (Imp) AC Power (Watts) MSRP

GTS-1440-1.8 8 –180 W 1440 1345 266 216 7.30 6.66 1800 $12,800.00

GTS-2004-1.8 12 –167 W 2004 1870 260 206 10.9 9.75 1800 $16,500.00

GTS-2160-1.8 12 –180 W 2160 2017 266 216 11.0 10.0 1800 $17,600.00

GTS-2338-2.5 14 –167 W 2338 2181 454 360 7.26 6.50 2500 $19,700.00

GTS-2520-2.5 14 –180 W 2520 2353 465 378 7.30 6.66 2500 $20,700.00

GTS-3006-2.5 18 –167 W 3006 2804 389 308 10.9 9.75 2500 $23,900.00

Module output “MC” cables

Panel “j-box” andbracket

Array “pull box”

Panel ground strapGround Lug

Panel to panel interconnect

Exclusive SunWize Panel “j-box” and mounting bracket saves assemblytime and hides wiring. Unique system provides interconnectionscheme for modules and a complete grounding system.


6/01

Battery Chargers

The SunWize™ Battery Charger uses advanced solar energy technology to charge the batteryin your generator, boat or car, providing the reliability and dependability you need.Accessories such as stereos, clocks, cellular phones and security systems can put a constantdrain on your battery. This battery charger is a convenient and cost-effective way to increasebattery life by maintaining the battery state-of-charge.

The SunWize proprietary polymer encapsulation process creates weather and impact resistantbattery chargers designed for outdoor equipment using 12 volt or 24 volt batteries. A 10 footcord is standard on all models. The Battery Chargers can easily be mounted or hung usingthe predrilled mounting holes.

Just plug the SunWize Battery Charger into your cigarette lighter or connect the clips to yourbattery terminals, place the charger in the sun and let Mother Nature do the rest!

SunWize Technologies, Inc.

SunWize™ BC1Battery Charger

Model BC2

Model BC3

Model/Description

BC1 W/Connector

BC2 W/Connector

BC3 W/Connector

SW Part Number

999FBC1

999FBC2

999FBC3

Voltage

12V

12V

12V

Dimensions

4.6” x 6”

9.5” x 6”

9.6” x 10.5”

Output

1W

2.5W

5W

OPTIONS – Choose connector type:1) Cigarette Lighter Adapter2) Spring Clamp Adapter

Amps

75mA

150mA

340mA

IDEAL FOR:• Trucks • Boats • Cars• Motor Homes • Campers• Airplanes • Motorcycles• Generators

FEATURES• Easy to use • Portable• Lightweight • Durable• Impact resistant • Environmentally friendly • Weather resistant• Built in blocking diode• Silent recharging


SunWize Systems

Portable Energy System

SUNW

IZE

SYST

EMS

3/03

The SunWize® Portable Energy System is a solar charging system for laptop computers andcommunication devices. The Portable Energy System converts solar energy into electricityallowing the user to operate or charge a battery-operated portable device anywhere outdoorsin direct sunlight.

SunWize’s proprietary technology encapsulates high-performance solar cells in a durable polymer resulting in solar panels that are weather and impact resistant. Inlocations with limited access to utility-supplied power orwhere brown outs are common, the SunWize Portable

Energy System provides the perfect power solution. Engineered with advanced solartechnology, this dependable system keeps electronics running efficiently even underadverse conditions.

The standard Portable Energy System includes a Multi-Volt Controller, two computer cablesand a multiple four-plug pinwheel cable for connecting the PES to other external electronicdevices, an owner’s manual, a self-storing 10-foot cord and a nylon storage sleeve.

Patented OPTI-MeterEach system is equipped with the SunWize OPTI-Meter, a patented LCDmetering system that allows the user to maximize performance and tomeasure the results. The metering system responds to light intensity – thehigher the number, the higher the power output. The user can achieve thehighest power by simply positioning the Portable Energy System on its built-instand to the highest meter reading.

Multi-Volt ControllerA SunWize exclusive, the Multi-Volt Controller is engineeredspecifically to regulate power flow between the Portable EnergySystem and the computer while providing proper voltage. It features an output for laptop computers as well as anadditional output for other electronic devices. A five-positionswitch allows the user to select the appropriate voltage from 3volts to 12 volts for that additional output.

System DoublerThe System Doubler is an optional panel that is connected to theMulti-Volt Controller to provide double the power for laptops using a Li-ion battery. This enables the user to run the laptop computer directlyfrom the sun! With the System Doubler, the user can optimize theSunWize Portable Energy System’s performance.

The SunWize™ OPTI-Meter

The SunWize™ Multi-Volt Controller

The SunWize Portable Energy System with System Doublerconnected to a laptop computer

The SunWize Portable Energy System provides dependable power for remote, off-grid locations. It provides truly portable power and INFINITE AUTONOMY™ for:

• Laptop Computer Users • Disaster Relief and Field Rescue Workers • Insurance Adjusters• Travelers, Backpackers and Mountain Climbers • Geologists and Surveyors• Scientific Expeditions • Sailors and Boating Enthusiasts • Military Personnel

Nylon Storage Bag

The Portable Energy System


SUNWIZE

SYSTEMS

3/03

SunWize Systems


Model/Description


System Doubler (One additional panel)

ACCESSORIESNylon Case, 2 panel pocket

Case, 2 panel pocket/1 computer pocket

MSRP

$379.95

$309.95

$39.95

$99.95

Solar Output

9.9 W

9.9 W

System Output

8.5 W

8.5 W

Dimensions LxWxD

10.5” x 15.5” x .56”

10.5” x 15.5” x .56”

Weight(lbs)

2.5

2.5

Portable Energy System Features:• Lightweight & portable – only weighs 2.5 lbs. including wire and stand• Weather-resistant• Totally automatic• Maintenance free - no moving parts• SunWize™ OPTI-Meter reads light intensity and measures power output• Built-in stainless steel stand to allow for continuous angle adjustment • Self-storing 10’ flexible, low loss connecting cable• Standard laptop connector cables included• Easy grip handle• Solar module output rated at 9.9 Watts; system output rated at 8.5 Watts• Size 10.5” x 15.5” x .56”• Multi volt controller weighs 4 ounces

Operates Most Portable Electronic Devices Such As:

• Laptop Computers

• Cellular Phones

• GPS Units

• CD Players & Radios

• Video Cameras

• Two-way Radios

• Medical & Environmental Equipment

• PDAs and Mobil Organizers

• Other products with rechargeable batteries

• Will recharge or trickle charge most products with rechargeable batteries

SunWize offers carrying cases constructed of DuPont 1050 Denier ballistic nylon.

Traveler:Carrying case with two panel pockets.

Laptop Traveler:Carrying case with two panel pockets and one computer pocket.

Palm Pilot andother types of PDAs

Digital Phones andCommunicationDevices

Mobil Organizers

GPS Units


SunWize Systems

Portable Power Generator

SUNW

IZE

SYST

EMS

3/03

The SunWize® Portable Power Generator (PPG) is a transportable source of battery power. Thisfully-integrated unit quietly generates DC or AC electricity to run small appliances such as lights,small televisions, fans, laptop computers and small power tools.

The SunWize Portable Power Generator is designed to be recharged from either a solar moduleor an optional AC battery charger. A controller monitors the charge to avoid under and overcharging the battery and a meter displays how much charge is in the battery. The AC modelincludes an internally mounted inverter that changes DC electricity to AC electricity for use withmost appliances. The externally mounted rocker switch lets you turn the inverter off and on as needed. The AC unit includes one 120VAC socket with an outdoor cover as well as2–7.5A, 12 VDC sockets mounted in the end panel. The base unit is also available in a DCversion with two DC sockets for 12V loads and a high-current DC output version with anadditional 30A DC socket for external inverter connections. The deep-cycle, marine grade batteryand solar module are optional.

The SunWize Portable Power Generator never needs fuel, is absolutely silent, and requires littlemaintenance. This portable generator, 73 lbs with a battery, is housed in a weather-resistant,polyurethane enclosure with lockable handles for carrying. All you need to do is plug the solarpanel into the generator to charge the battery. Once the battery is charged, you are ready to go!

The SunWize Portable Power Generator is available in 3 basic models - a 12 amp AC version with a 150 watt inverter, a 12 ampDC and a 30 amp DC version. Models above shown with optional solar PV Module.

Ideal for:■ Emergency Power■ Disaster Relief Power■ Remote Power■ Camping & Boating■ Tool Sheds, Barns■ Construction Sites■ Farms■ Field Work

■ Completely assembled and factory tested

■ Portable and ready to use

■ Simple ‘plug and go’ operation

■ External inverter switch (AC Model only)

■ PV module mounting accessories

■ 120VAC socket with outdoor cover (AC Model only)

■ Internal 150-watt, 120VAC inverter (AC Model only)

■ Battery meter indicates state-of-charge

■ Sockets separately fused

■ Corrosion and weather-resistant, rugged,

non-breakable enclosure

■ Designed for DC charging by solar panels

■ 2 DC sockets for 12V loads up to 90W each

■ Environmentally friendly

Features:

Portable Power Generator – Base Model

2 DCSockets

PV Input

BatteryMeter

ExternalInverterSwitch

120 VoltAC Socket

Portable Power Generator – AC Model


SUNWIZE

SYSTEMS

3/03

SunWize Systems

Portable Power Generator

Model Controller Inverter Dimensions Weight MSRP

Base AC 12 amp Internal 150 watt 21” x 15” x 12” 10 lbs $669.00Base DC 12 amp N/A 21” x 15” x 12” 9 lbs $519.00Base DC 30 30 amp N/A 21” x 15” x 12” 9 lbs $639.00

Sample Usage per Day: (Watt hours = estimated wattage of appliance X hours of run time)Appliance Wattage X Run Time = Watt Hours2- 15W lights 15W 8 hours (4 hrs each) = 120 Wh1 Television 50 W 2 hour = 100 Wh1 Fan 25 W 4 hours = 100 Wh

TOTAL Wh per day usage: = 320 WhEstimated Operating Time: 6 days. Estimated Recharge Time: 4.5 full sun days for a completely discharged system.

Please note: SunWize uses true, deep-cycle batteries. These batteries are also used for military applications and by airlines. Figures willvary based on geographic location.

Model Controller Inverter PV Module Battery Dimensions Weight MSRP

AC 40/65 12 amp Internal 150 watt 40 watt 65 Ah 21” x 15” x 12” 53 lbs $1149.00



DC 40/65 12 amp N/A 40 watt 65 Ah 21” x 15” x 12” 52 lbs $979.00



DC30 50/100 30 amp N/A 50 watt 100 Ah 21” x 15” x 12” 73 lbs $1249.00

DC30 75/100 30 amp N/A 75 watt 100 Ah 21” x 15” x 12” 73 lbs $1469.00

Accessories


Universal AC Battery Charger 110-240 VAC, 50/60 Hz with DCI-PPG plug $95.00

External US-Voltage Inverter Modified sine-wave, 250W/120VAC/60Hz with 30A plug $159.00

External Euro-Voltage Inverter Modified sine-wave, 250W/230VAC/50Hz with 30A plug $175.00

External Sine-Wave Inverter True sine-wave, 300W/120VAC/50Hz with 30A PPG plug $439.00

40 W Module Additional 40 W module with 2 module interconnect kit $395.00



TL Light Fixture 8 W Fluorescent, 8 W with 20 ft. cord and DCL-PPG plug $48.00

TL Light Fixture 15 W Fluorescent, 15 W with 20 ft. cord and DCL-PPG plug $52.00

DC Load Plug (male) 12V, 10A maximum, for wiring additional DC load equipment $3.00

DC Input Plug (female) 12V, 15A maximum, for wiring additional DC input equipment $10.00

Module Mounting Hardware See “Module Mounting Hardware” section

For your convenience, the SunWize™ Portable Power Generator is also available as a complete package in three ACversions and five DC versions.

Sample Usage Chart: Model # AC75/100Consists of base unit with controller, 75 watt module and 100 Ah battery. AC version includes a 150 watt inverter. The fullycharged battery provides 1050 Wh DC, (950 Wh AC). A 75 watt module provides 190 Wh per 4 full sun hours.

The SunWize Portable Power Generator is available in 3 basic models - a 12 amp AC version with a 150 watt inverter, and a12 amp DC and a 30 amp DC version. All base units include a 20 ft., 12/2 cable with a DC input plug. You provide your ownbattery and module.


6/01

Solisto™ Solar Home Controller

SunWize TechnologiesThe SunWize® SoListo is a prepackaged control unit designed for rural home electrification.Just add batteries and modules for a complete solar home system that replaces dry cellbatteries, kerosene and candles with safe, dependable solar energy. These systems supplyelectricity for lighting, entertainment and information to homes that are not connected to utilitypower grids. The SoListo includes electronic system safeguards and provides years of reliableservice and convenience.

The basic SoListo system is designed to provide power for DC fluorescent lights and a smalltelevision or radio. A controller monitors battery charging to avoid under or over charging thebattery and an LED light displays how much charge is in the battery. The AC model includesan internally mounted inverter that changes DC electricity to AC electricity.

The SunWize SoListo never needs fuel, is absolutely silent and requires little maintenance.Complete systems including modules and batteries are available. DC fluorescent lights arealso available as well as other accessories.

The SunWize™ Solisto

Ideal for■ Rural Home Electrification ■ Remote Cabins ■ Tool Sheds and Barns ■ Emergency Power

■ Prepackaged and pre-wired – National

Electric Code compliant

■ "Intelligent" battery charger maximizes output

from solar module

■ 12VDC and multi-volt (9, 7.5, 6, 3 volts) outlets

■ Main battery/solar module disconnect switch

with safety fuses

■ Optional AC inverter

■ Attractive wall mounted cabinet with

international labeling

■ Sealed or flooded battery adaptable,

preset to sealed

■ Battery polarity indicator lights

■ Solar charging/system status light

■ Battery state-of-charge indicator light

Features:

■ Silent operation

■ High reliability

■ Low maintenance

■ No fuel dependence

■ Modular design allows system expansion

■ Easy installation

■ Clean energy

■ Power for any location

Benefits:

Typical SoListo ConfigurationShown with optional module and battery

SOLISTOControl Panel


6/01

Model Output Voltages PV/Load Current Inverter Weight SW Part NumberSHC–DC 12, 9, 7.5, 6, 3 VDC 8A, 12A or 20A N/A 4.1kg 996SHCXXDCMV-A

(specify current) 9 lb.

SHC–AC 120VAC/60Hz,* 8A, 12A or 20A 200 Watt 4.7kg 996SHCXXACMV-A12, 9, 7.5, 6, 3 VDC (specify current) (internal) 10.25 lb.

*Other AC voltage/frequencies available XX – Specify Current

Mechanical SpecificationsMaximum PV/Battery Wire Size 13.6 mm2 (#6 AWG)Maximum Load Wire Size 5.2 mm2 (#10 AWG)Dimensions 40cm X 28 cm X 6 cm

(15 5/8" X 11" X 2 3/8")Weight (without inverter) 4.1 kg (9 lb.)Enclosure Rating Indoor

Electrical SpecificationsNominal Operating Voltage 12 VMaximum PV Input Amps 8 A / 12 A / 20 AMaximum Load Amps 8 A / 12 A / 20 AMain Fuse 10 A / 15 A / 20 ASelf-Consumption 10 mAOperating Temperature –25º C to 50º C

Output SpecificationsMulti-Volt Outlet (with 2.5mm plug)Nominal Voltage 9VDC 7.5VDC 6VDC 3VDCMaximum Load Amps 1.5 A 1.5 A 1.5 A 1.0 A(2 Amp Fuse)

12V Outlet (with cigarette lighter plug)Nominal Load Voltage 12VDCMaximum Load Amps (fused) 5 A

Direct-Wired 12VDC Load Terminals (max. 2 circuits)Nominal Load Voltage 12VDCMaximum Load Amps 7.5 AMaximum Wire Size 5.2 mm2 (#10 AWG)

SolarCharging

Light

BatteryLevelLight

Main Safety

Disconnect

SafetyLock

BatteryOutput

PV Input

Multi-VoltControlLights

Multi-VoltSelectorSwitch

Load Output

AC Outlet(AC models only)

12VDCSocket

Multi-VoltSocket

Application:Solar Electric Systems for Rural Electrification

Location: Moris andTemosachi, State ofChihuahua, Mexico

Description: SunWizeTechnologies developed 200solar home systems as part ofa rural development project inMexico to provide electricity forfluorescent lights and small appliances. Each systemincludes a 50 watt module, a12 volt DC battery and theSoListo™ controller, a productdesigned and manufactured bySunWize for this project.SoListo controllers, available ina DC or AC model, are

prepackaged andpre-wired in a wall-mounted cabinet.LED lights displaywhen the solarmodule is chargingthe battery andhow much chargeis in the battery tohelp the owner useelectricity wisely.The SoListo alsoincludes a 12VDCoutlet and a multi-

volt outlet (3, 6, 7.5, and 9V) with a multi-volt selector switch.The AC model includes an internally mounted inverter andan AC outlet.System Components: 50 watt PV module and aluminumpole-mounting structure; 12 volt DC battery and batteryenclosure; SoListo Controller.

Solisto™ Solar Home Controller A d v a n c e d E n e r g y G r o u p

SunWize Systems

Power Ready System

SUNW

IZE

SYST

EMS

3/03

SunWize® Power Ready Systems are complete, fully integrated power supplies designed for siteloads requiring 12, 24 or 48 volts DC. Each system provides safe and reliable power generationwithout the need and expense of installing utility power. The sealed, maintenance free batteriesare designed for deep cycle operation and extended life in solar applications. The aluminum arraysupport structures and battery enclosures arestrong yet lightweight and corrosion resistant forharsh marine or severe weather locations.

Because Power Ready Systems are designed towithstand rugged transportation to remote sites,single-lift integral lifting lugs and/or forklift slots are

provided. Optional helicopter handling featuresare also available. The system is fully assembled

for factory testing before shipment. The prewired systems are typically shippedfully assembled with a protective cover over the array and are bolted to a skid.The solar array for larger systems is shipped in a separate plywood crate and thebattery enclosure is mounted on a skid. In some cases, batteries are shipped

separately. Power Ready Systems carry a one-year system warranty for materials and work-manship. A three-year SunWize performancewarranty is available on pre-packaged systems.The solar modules have up to a 25-yearwarranty. Careful component selection resultsin a system with a lifetime exceeding 25 yearswith battery replacements every five to ten years.

Industrial Prepackaged Solar Power Systems for:■ Telecommunications■ RTU/SCADA Applications■ Data Collection■ Instrumentation■ Security Lighting & Surveillance■ Navigational Aids■ Flow Monitoring■ UHF/VHF Radio■ Seismic Monitoring■ Tank Gauging■ Radio Telephones ■ Railroad Signaling■ Area/Sign Lighting■ Cellular Extenders■ Microwave Repeaters■ Cathodic Protection■ Irrigation Control

High-efficiency, singlecrystalline solar modulesdeliver maximum poweroutput and carry up to a25–year warranty

PV array shadesbattery box tominimize batterytemperatureextremes

Insulated batteryenclosure is available in a variety of materialsand finishes

Preassembled andprewired systems minimize fieldinstallation time

NEC code compliant overcurrentprotection and safety disconnect

Universal anti-theftmounting hardwareavailable for outdoor pole or wall mounting

Corrosionresistantcontrol/battery enclosure

Sealed, lead-acid battery designed for deep discharge cycling

Solid state electronics display battery state-of-charge and controller status/errors

Solar modules are fully encapsulated to resistharsh weather conditions

12 Volt PEAK SUN HOURS 24 VoltSYSTEMS 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 SYSTEMSPR005-12-019 0.2 0.3 0.4 0.6 0.7 0.8 1.0 1.1 1.2 1.4 1.5 PR010-24-019

PR010-12-038 0.5 0.7 1.0 1.2 1.5 1.7 2.0 2.3 2.5 2.8 3.1 PR020-24-038

PR020-12-038 1.0 1.5 1.9 2.4 2.8 3.4 4.0 4.4 5.0 5.6 6.2 PR040-24-038

PR040-12-079 1.9 2.8 3.8 4.8 5.6 6.7 7.8 8.6 9.8 11.0 12.2 PR080-24-079

PR050-12-120 2.4 3.6 4.8 6.0 7.1 8.5 9.8 10.9 12.3 13.8 15.2 PR100-24-120

PR075-12-120 3.5 5.3 7.0 8.8 10.0 11.9 14.1 15.5 17.7 20.0 22.3 PR150-24-120

PR090-12-240 4.1 6.2 8.2 10.4 12.6 14.7 17.2 19.1 21.5 23.8 26.2 PR180-24-240

PR115-12-240 5.5 8.2 11.0 13.8 16.2 19.2 22.4 25.0 28.2 31.6 35.0 PR230-24-240

PR150-12-240 7.1 10.6 14.0 17.5 20.0 23.9 28.2 31.1 35.3 40.3 44.5 PR300-24-240

PR180-12-240 8.3 12.5 16.2 20.0 24.0 27.6 32.6 35.4 40.9 47.2 52.5 PR360-24-240

PR230-12-240 11.0 16.3 21.0 25.8 28.8 34.8 41.2 44.3 51.8 61.7 70.0 PR460-24-240

PR230-12-480 11.6 16.5 22.0 28.2 32.2 38.4 44.9 50.0 56.6 63.4 70.0 PR460-24-480

PR300-12-600 14.4 21.6 28.8 36.0 43.2 50.4 57.6 64.8 72.0 79.2 86.4 PR600-24-600

PR360-12-750 17.3 25.0 33.2 42.2 49.4 59.2 68.4 76.6 85.7 96.0 105.0 PR720-24-750

PR425-12-750 19.8 28.6 38.0 48.3 56.6 67.8 78.3 87.7 98.1 109.9 120.2 PR850-24-750

PR460-12-900 22.1 33.1 44.2 55.2 66.2 77.3 88.3 99.4 110.4 121.4 132.5 PR920-24-900

PR510-12-1000 24.7 35.8 47.3 59.8 69.0 82.0 96.2 106.8 120.4 133.5 148.0 PR1020-24-900Note: Each system was designed for a Loss of Load Probability (LOLP) of less than 0.1% for the worst month. • Contact SunWize for 48 Volt system selections.

(Figures below are daily load in Amp–hrs/day.Refer to the map at www.sunwize.com/catalog/images/map.gif)SYSTEM SELECTION TABLE


SUNWIZE

SYSTEMS

3/03

SunWize Systems

Power Ready SystemsStandard Features and Benefits

Solar modules are fully encapsulated to resist harsh weather conditions

Low voltage load disconnect for battery protection

Sealed, lead-acid battery designed for deep discharge cycling

NEC code compliant overcurrent protection and safety disconnect

Temperature compensated battery charging

Corrosion resistant control/battery enclosure

Installation, operation & maintenance documentation

Solid state electronics for improved efficiency and reliability

Preassembled, prewired systems minimize field installation time &eliminate wiring errors

Low maintenance and operating costs

Complete systems reduce specifying and buying time

Quality components assure long system life

Full system and performance warranty available on prepackagedsystems

System Options (choose ANY & enter into SunWize Part Number)

a. DC to DC converter (specify output voltage/current)

b. DC to AC inverter (specify output voltage/current)

c. Data logging / Remote monitoring

d. Cathodic protection controller

e. Electronic load compartment

f. Theft deterrent solar module hardware

g. Helicopter lifting lugs

h. Bird deterrent (stainless steel strips for solar module)

Controller Options (choose ONE & enter into SunWize Part Number)

i. SunWize LCD - displays battery voltage, SOC, charging & load current,controller status/errors

j. SunWize LVA - low battery SOC/load disconnect contact closure

PR ■■■■ ■■ – ■■ ■■ – ■■■■■■– ■■ – ■■ – ■■ ■■ – ■■ ■■ – ■■– ■■

LightningProtection

WireProtection

MountFinish

EnclosureFinish

ModuleMount Type

EnclosureType

BatteryAmp-hr Rating

SystemVoltage

ModuleWattage

▼▼ ▼ ▼

▼ ▼

▼ ▼

▼

KEY TO SUNWIZE PART NUMBER LoadDistribution

▼

SystemOptions

▼

Module Wattage

System Voltage

12 volts

24 volts

48 volts

Battery Amp-hr Rating (based on 100-hour discharge rate)

Enclosure Type

F – Front opening hinged door, pole mounted

T – Top opening hinged door, ground/pad mounted

C – Front opening door (screw-type), pole mounted

E – Economy

Module Mount Type

I – Integral with enclosure

P – Pole mount, separate from enclosure

G – Ground mount, separate from enclosure

Enclosure Finish

A – Milled aluminum (standard)

W – Powder coated white aluminum

S – Galvanized steel

F – Fiberglass reinforced polyester

Mount Finish

A – Milled aluminum

P – Painted steel

S – Galvanized steel

Wire Protection

0 – PV and battery wired directly to controller,fused battery line

1 – DC-rated circuit breakers for PV and battery (standard – NEC compliance)

Lightning Protection

0 – Standard MOV surge protection

1 – Silicon-oxide varistor (SOV)

Load Distribution and Control

0 – None, load wired directly to controller

1 – Four terminal load distribution block (standard)

2 – DC-rated circuit breaker

3 – Multi-cycle timer

HOW TO SELECT YOUR SYSTEMThe chart below specifies a system designed to meet the daily loadof your equipment.

1) Use the map located at www.sunwize.com/catalog/images/map.gifto select the zone that corresponds to the equipment site location.2) Determine your daily equipment load requirement in Amp–hrs/dayat the specified voltage. 3) In the Selection Table, under your “peak sun hours” column, find thevalue of Amp–hours/day that is greater than or equal to your load. Based on your system voltage, select your SunWize part number.


SunWize Systems

Power Station

SUNW

IZE

SYST

EMS

3/03

The SunWize® Power Station consists of a PV array which generates DC electricity from sunlight,a battery bank to store the DC energy and an inverter to convert from DC to utility-grade AC electricity.

Several factors must be considered when choosing between a hybrid or stand-aloneconfiguration. Hybrid stations are sized to provide 25-75% of the load requirements by theengine generator, resulting in a lower first-cost for a given load. Stand-alone PV systems aresized to provide 100% of the load and offer very low operating and maintenance costs.

SunWize PV Hybrid Power Station Components Diagram1800W Power Station

1. Photovoltaic (“PV”) PanelsHigh-efficiency, single crystal silicon PV modules provide higher amp-hour per watt output than other technologies and include dual bypassdiode protection. Modular PV panels permit expansion to accommodate increased loads.

2. Adjustable Array StructurePV array tilt is easily adjustable from 30-60 degrees to maximize solar energy. Further adjustment of 0-30 degrees possible with specialpositioning bars. 2400W available with non-adjustable tilt only.

3. Control CenterThe control enclosure is a NEMA 3R powder-coated steel box housing the powerdistribution components (DC controller/distribution, inverter and AC distribution),disconnects, system monitor and appropriate wire terminals. Enclosure is providedwith rainproof vents and a ground fault protected electrical outlet. Optional remotemonitoring equipment is available.

4. Inverter/Battery ChargerXantrex microprocessor-controlled, high-efficiency sine wave inverterwith three-stage, temperature-compensated battery charger. Peakconversion efficiency of 96%, protection circuitry, LCD display with userand setup menus.

5. DC ControllerSolid state, low frequency, pulse-width modulated solar charge controlwith battery temperature compensation and automatic night timedisconnect. Customer DC interface conforms to U.S. National ElectricCode and provides easy access and flexibility for multiple DC loadrequirements.

6. AC Distribution PanelOutput AC breaker panel conforms to U.S. National Electric Code, provides surgeprotection and flexibility for multiple AC load requirements.

7. DC Combiner BoxProvides PV circuit disconnects and lightning/surge protection for electronic equipment.

8. Ventilator FanDesigned for active ventilation of hybrid battery enclosure to prevent accumulation of hydrogen gas.

9. BatteriesAvailable in three battery types: economy flooded lead-acid, industrial flooded lead-acid and sealed lead-acid. Flooded lead-acid batterycomes with recombiner caps to minimize water loss. Sealed battery available for maintenance-free performance. The control systemmaintains the batteries between 20% and 100% state of charge.

10. Battery EnclosureSealed batteries are housed in a NEMA 3R powder-coated steel, lockable enclosure with filtered vents. Flooded batteries are housed in aninsulated, vented thermoplastic unit with lockable lid and drain plug. Designed to minimize battery temperature extremes, eliminate batterybank hot spots, prevent freezing and extend useful battery life.

11. Generator (Hybrid only)Commercial and Industrial engine generators available to meet requirements. Includes battery, alternator, remote start/stop contacts, self-contained protection and automatic safety shutdowns. Package includes weatherproof housing, vibration isolators on steel skid, flexiblecouplings, and replaceable dry element air filter. Propane and diesel fuel types available. Contact SunWize for other genset availability.

12. StructureIndustrial grade, heavy-gauge steel coated with a durable hot–dip galvanized finish. Available in four configurations: ground mount, road trailer, off-road trailer and breakdown kit.

12

1

2

34

56

78

9

10

11


SUNWIZE

SYSTEMS

3/03

SunWize Systems

Power Station

Choose from the above charts and fill in the blanks below to configure your own system.Example:

Inverter Battery Generator Structure MonitoringType Array Option T Option B Option G* Option S Option M

_______ _______ _______ _________ _________ ________ _________

Your SW part number is: PSG900-T4024-B01-G04-S01-M02

How to configure your own system

Model/Description

Hybrid Power Station - 900 Wp





PV Power Station - 400Wp






SW Part Number

PSG900

PSG1200

PSG1500

PSG1800

PSG2400

PS400

PS900

PS1200

PS1500

PS1800

PS2400

Array(Wp)

900

1200

1500

1800

2400

400

900

1200

1500

1800

2400

Overall Dimensions

155" x 166" x 119"

155" x 166" x 151"

155" x 166" x 151"

155" x 166" x 151"

155” x 166” x 151”

155" x 166" x 119"

155” x 166” x 151”

155” x 166” x 151”

155” x 166” x 151”

155” x 166” x 151”

Weight±200 lbs.

2900 lbs

3000 lbs

3100 lbs

3200 lbs

3400 lbs

2200 lbs

2800 lbs

2900 lbs

3000 lbs

3200 lbs

Stand-Alone/Hybrid

Hybrid (PSG)

Hybrid (PSG)

Hybrid (PSG)

Hybrid (PSG)

Hybrid (PSG)

Stand-Alone(PS)

Stand-Alone(PS)

Stand-Alone(PS)

Stand-Alone(PS)

Stand-Alone(PS)

Stand-Alone(PS)

PSG 900 - T4024 - B01 - G04 - S01 - M02

Standard Components:

• Photovoltaic (“PV”) Panels -

(reference pages 2-13)

• Inverter/Battery Charger

(reference pages 41-51)

• Batteries (reference pages 32-34)

• Generator (Hybrid Only)

Options:• Consult Factory for Custom Options

Inverter Power/Voltage

Option T Order #

1.5kVA, 12VDC: 120VAC T151260Hz, 1Ø, 2-wiremodified sine wave

3kVA, 24VDC: 230VAC50Hz, 1Ø, 2 -wire T3024E

4kVA, 24VDC: 120VAC60Hz, 1Ø, 2 -wire T4024*

4kVA, 24VDC: 220VAC60Hz, 1Ø, 2 -wire T4024W

4.5kVA, 48VDC: 230VAC50Hz, 1Ø, 2 -wire T4548E

5.5kVA, 48VDC: 120VAC60Hz, 1Ø, 2 -wire T5548

8kVA, 24VDC: 120/240VAC60Hz, 1Ø, 3 -wire T8024D

8kVA, 48VDC: 120/240VAC60 Hz, 1Ø, 3 -wire T8048D

* Denotes standard configuration equipment.

Battery (100 hour rating)

Option B Order #

Industrial lead acid,flooded 2V cells, 1000Ah @24 volt500Ah @ 48 volt B01

Economy lead acid,

flooded 6V cells, 700Ah @ 24 volt350Ah @ 48 volt B02

Valve-regulated lead acid,sealed 12V cells500Ah @ 12 volt250Ah @ 24 volt B03

Valve-regulated lead acid,sealed 12V cells1500Ah @ 24 volt750Ah @ 48 volt B04

Valve-regulated lead acid,sealed 12V cells, 1000Ah @ 24 volt500Ah @ 48 volt B10*

Generator

Option G Order #

6kVA air-cooled, 2-cyl, LP(propane) fuel G01

10kVA water-cooled,4-cyl, LP(propane) fuel G04

7.5kVA water-cooled,2-cyl, diesel fuel G09

8.5kVA air-cooled,2-cyl, LP fuellight duty G08

Structure

Option S Order #

Ground Mount S01*

Ground Mount, breakdown kit S02

Heavy-duty Road-ratedTrailer, dual-axle S03

Off-Road (AgriculturalUse) Trailer S04

Road Rated Trailer S054’ x 6’ single axle

Monitoring

Option M Order #

LocalMonitoring M01*

RemoteMonitoring/Control Panel50 ft. cable M02

RemoteMonitoring/Control adapter & PCSoftware M03

Features:• Pre-assembled & Factory Tested• Self-supporting, ballasted design requires no foundation• Modular design for system expansion• Adjustable array maximizes power• Easy Installation• Reliable, continuous power for critical loads• Low maintenance

Applications:• Telecommunications• Disaster relief and emergency power• Village electrification• Remote residential and industrial applications• Irrigation and water pumping

Trailer Mounted only

* do not specify Option G for stand alone (PS) systems


Industrial DC Power Supply

Integrated Outdoor DC Power Supply with Battery BackupThe SunWize BC-series DC power supply provides regulated power and hours of backup runtime for DC loads. This fully integrated unit converts AC mains power to DC in order to floatcharge the battery bank while powering the DC load. Upon loss of mains, the battery powersthe DC load(s) with zero transfer time, because the loads are connected to the battery bank100% of the time. The unit is comprised of a switch mode rectifier with 3-stage charging,maintenance-free, deep-cycle batteries and full circuit protection. The circuit is fully protectedvia breakers and fuses on the AC input, connection to the batteries, and DC loads. Theoutdoor, lockable, aluminum enclosure includes tamper-proof hardware suitable for pole or wallmounting. User’s manual and full wiring schematics for quick wiring are included. Variousbattery sizes are available. Temperature compensated models are available to increase batterylifetime and prevent thermal runaway. DC ripple <50mV. One-year warranty.

Options include:

(A) AC fault detection relay

(B) DC to DC converter for additional 12, 24 or 48V output (Option B1=10 A; B2=30 A)

(C) low battery voltage closed contact alarm relay

(D) low voltage battery disconnect.

SunWize Technologies

6/01

Output Input Output Temperature Battery@Model Current Voltage Voltage Compensation 20 hr rate (Ah) Weight SW Part Number

BC2524100 25 amp 115 VAC 26.8 VDC yes 100 Ah 190 lbs 999BC25AT24V

BC1524100 15 amp 115/230 VAC 26.8 VDC no 100 Ah 190 lbs 999BC15A24V

BC4512200 45 amp 115 VAC 13.4 VDC yes 200 Ah 190 lbs 999BC45AT12V2

BC4512100 45 amp 115 VAC 13.4 VDC yes 100 Ah 125 lbs 999BC45AT12V1



The SunWize® BC-SeriesDC Power Supply


6/01

The SunWize® Backup Electric Systems are fully integrated and automated power packages.The systems are designed to maintain a home’s basic loads such as lighting, refrigeration,furnace fan, sump pumps and television for one to five days depending on user habits andconservation during power outages. When the utility is providing AC power to the inverter/charger, the system will act as a battery charger to keep the DC battery storage bank fullycharged. When the primary source of AC power fails, the system becomes an inverter thatconverts the DC battery power into utility-grade AC power. The transfer is completelyautomatic.

The SunWize Standby Power Systems are capable of charging from solar-electric modulesand/or a generator using an optional charge controller with a DC circuit breaker. The controllersuse DC power from the solar modules to charge the battery bank. The controllers also protectthe batteries against overcharging and automatically disconnect the solar array at night.

The SunWize Standby Power Systems are available in eighteen models ranging from 2 kWhr - 40 kWhr battery capacity. The connections to the AC utility and AC load subpanel aremade at the AC input/output/bypass breaker. The bypass breaker allows the inverter to beisolated from the AC source during maintenance service. The unit also features an AClightning arrestor and an AC input surge capacitor. Please note that a licensed electrician mustinstall the SunWize Backup Electric Systems.

The battery bank of valve-regulated, deep-cycle, lead-acidbatteries is separated from theinverter / charger by a 250A DCcircuit breaker. The circuit breakeracts as a disconnect and protectsagainst the extremely high batterycurrents in case of a short-circuit.A battery temperature sensor,included for installation within thebattery bank, feeds a signal backto the inverter/charger toautomatically adjust battery chargevoltage. A 500A, 50mV shunt isalso provided for battery currentflow measurements.

SunWize Technologies

The SunWizeStandby Power System

AC Breakers

ChargeControllers

FEATURES:• Reliable, quiet and easy to

operate

• Aluminum enclosure with lockable cover and mounting feet

• Pre-wired and packaged for easy installation

• AC and DC overcurrent protection breaker

• Maintenance free, deep-cycle, lead-acid batteries

• DC ground fault protection

• Modular design for flexibility

DC Breakers

Sealed Batteries

OPTIONS:• Solar Power Kit

• Propane / Diesel Generator

• Wind Power Kit

• Additional inverter is available for 120/240 VAC 60 Hz

Backup Electric Systems

Model System Nominal AC Output Battery SW Part Number Rating Input Voltage Voltage Capacity

SW2000-2 2,000W 12VDC 120VAC 2kWh SW2000-2SW2000-8 2,000W 12VDC 120VAC 8kWh SW2000-8SW3500-4 3,500W 48VDC 120VAC 4kWh SW3500-4SW3500-16 3,500W 48VDC 120VAC 16kWh SW3500-16SW5000-8 5,000W 48VDC 120VAC 8kWh SW5000-8 SW5000-20 5,000W 48VDC 120VAC 20kWh SW5000-20SW7000-8 7,000W 48VDC 120/240VAC 8kWh SW7000-8SW7000-30 7,000W 48VDC 120/240VAC 30kWh SW7000-30SW10,000-10 10,000W 48VDC 120/240VAC 10kWh SW10000-10SW10,000 -40 10,000W 48VDC 120/240VAC 40kWh SW10000-40

Lower Cost Backup Electric Systems

TS400-450 400W 12VDC 120VAC 400Wh TS400TS-400TS400-2 400W 12VDC 120VAC 1.6kWh TS400TS-2DR1000-1 1,000W 24VDC 120VAC 1kWh DR1000DR-1DR1000-4 1,000W 24VDC 120VAC 4kWh DR1000DR-4DR2000-2 2,000W 24VDC 120VAC 2kWh DR2000DR-2 DR2000-8 2,000W 24VDC 120VAC 8kWh DR2000DR-8DR3000-3 3,000W 24VDC 120VAC 3kWh DR3000DR-3DR3000-12 3,000W 24VDC 120VAC 12kWh DR3000DR-12


SunWize Systems

SunWize® Designer Lighting Systems (DLS) use solar technology to provide lightingin areas where there is no utility power or where excavation for underground powerlines make utility power too costly.

The SunWize Designer Lighting Systems combine the latest technology availableto provide years of reliable, low maintenance operation. The DLS control panel andbatteries are contained in a ‘slim-line’, outdoor enclosure and is fully tested with afactory assembled control panel for simple, trouble free installation.

The SunWize Designer Lighting Systems use an ultra high efficiency luminaire thatincorporates computer-designed, polished specular reflector to maximize thelighting intensity and coverage area. SunWize Designer Lighting Systems are colorcoordinated in attractive powder coated architectural bronze including the optionalpole and arm.

The luminaire is available with either low pressure sodium (LPS) or fluorescent (FL)lamps. The LPS lamp is a monochromatic (yellow-orange) light source, deliveringthe highest possible lumens per watt. Compact fluorescent lamps provide slightlyless lumens, but produce a white light (4100K), which appears brighter than lowpressure sodium lamps and should be used in areas where color rendition is desired.

DLS’s are offered with a choice of light fixtures:

Fixture Rated Lumens

35 W LPS 480055 W LPS 800072 W Fluorescent 5800

Battery box dimensions:

# of Batteries Dimensions

2 32” x 16” x 10”4 32” x 16” x 16”

Solar Designer Lighting Systems

SUNW

IZE

SYST

EMS

3/03

APPLICATIONS • Residential roadways and intersections • School ground security lighting • Marinas and campgrounds • Parks and recreation areas • Community area lighting • Parking lots • Bicycle and jogging paths • Marinas and campgrounds

FEATURES AND BENEFITS • Eliminates utility line extensions • Fast and easy installation• Location flexibility • Maintenance free, long life ‘AGM’ batteries• Automatic lighting controller with adjustable run times • Over-current protection and status LEDs

Vented, outdoor battery and

control enclosure

High density solar moduleshave a 20+ year warranty

Entire pole-mounted system is designed to withstand 90 MPH wind loads

Pole top mount adjusts 0–90˚ horizontal and 360˚ about pole

Luminaire with captive screw, hinged cover and slip fits on 2” sch. 40 pipe/arm.

Door has keyed, locking mechanism

Vandal-resistant enclosureand mounting brackets

Convenient wiring access


DLS Run-Time Operation Guide

Geographical location- sun hours 20ft. pole # ofDLS Model # 2.0-2.9 3.0-3.9 4.0-4.9 5.0-5.9 6.0 + SQ. size Batteries MSRP

DLS-90-160-35 4hr 6hr 8hr 5” 2 $2799.00DLS-120-160-35 4hr 6hr 8hr 10hr 5” 2 $3199.00DLS-150-200-35 4hr 6hr 8hr 10hr D/D 5” 2 $3499.00DLS-220-250-35 6hr 8hr 10hr D/D 5” 2 $4299.00DLS-240-320-35 8hr 10hr D/D 5” 4 $4899.00DLS-270-320-35 10hr D/D 6” 4 $5099.00DLS-330-400-35 D/D 6” 4 $5899.00DLS-110-100-55 4hr 6hr 8hr 5” 2 $3399.00DLS-150-100-55 4hr 6hr 8hr 10hr 5” 2 $3649.00DLS-180-120-55 4hr 6hr 8hr 10hr D/D 5” 2 $3899.00DLS-240-125-55 6hr 8hr 10hr D/D 6” 2 $4549.00DLS-300-200-55 8hr 10hr D/D 6” 4 $5749.00DLS-340-240-55 10hr D/D 6” 4 $6049.00DLS-440-250-55 D/D 6” 4 $7199.00DLS-110-200-72 4hr 6hr 8hr 5” 2 $3339.00DLS-150-200-72 4hr 6hr 8hr 10hr 5” 2 $3599.00DLS-180-240-72 4hr 6hr 8hr 10hr D/D 5” 2 $3849.00DLS-240-250-72 6hr 8hr 10hr D/D 5” 2 $4499.00DLS-300-400-72 8hr 10hr D/D 6” 4 $5699.00DLS-340-480-72 10hr D/D D/D 6” 4 $5999.00DLS-440-500-72 D/D 6” 4 $7149.00

SUNWIZE

SYSTEMS

3/03

SunWize Systems

Solar Designer Lighting Systems

Select Lamp Watts and Run Time-Hrs desired vs worst case sun hours in your location.Visit www.sunwize.com/catalog/images/map.gif for world insolation map reference.

The table above illustrates standard systems. For competitive bids or other systemcombinations not listed, professional computer aided lighting system design services arefree of charge.

Contact your salesperson to determine the most cost effective solution for your location.

Options: (ordered separately) MSRPDLS-A– Pre-assembled PV array, top pole mount & wiring $90 per moduleDLS-B– Protective aluminum module back plates $70 per moduleDLS-C*– 6” sq. x 30’ pole ( reduces wind load to 80 mph) $1800.00

w/4’ arm & 4-1” x 36” anchor bolts

MSRPDLS-D*– 6” sq. x 20’ pole w/4’ arm & 4-1” x 36” anchor bolts $1700.00DLS-E*– 5” sq. x 20’ pole w/4’ arm & 4-1” x 36” anchor bolts $1100.00DLS-F–Lightning Surge Protection $70.00

• DLS model numbers depict PV watts - Battery AH - Lamp watts - Options. (example: DLS-90-160-35)

• Standard systems are offered – less pole and arm

Horizontal Foot Candles@20 foot Mounting Height

FIXTURE TYPECONTOUR 35W LPS 55W LPS 72W FL

A 2.0 3.5 3.0B 1.5 2.5 2.2C 1.0 1.6 1.5D 0.7 1.2 1.0E 0.4 0.8 0.6F 0.2 0.5 0.3G 0.1 0.3 0.2

50’ x 50’ Grid Area

* Price for poles includes pole, arm, enclosure mounting brackets, U-bolts and other hardware. FOB destination – domestic US on minimum order of 4 poles


SunWize Systems

Enjoy all the benefits of solar power with an easy-to-install, simple-to-use RV Power Kit fromShell Solar. RV Power Kits give you the freedom to escape from crowded campgrounds andnoisy generators with your own independent power source fueled by the sun.

The science of the RV Power Kit is simple: the more sunlight the solar panel can absorb, themore power your system provides. Whenever the sun shines on the panel, electricity is producedand fed into your vehicle’s 12 volt battery.

The RV Power Kit provides you with everything you need to install your own efficient, reliablesolar power system and begin generating electricity. The heart of the kit is the high efficiencysolar panel that converts sunlight into direct current (DC) electricity. A charge controller keepsyour batteries fully charged, and at the same time, protects them from overcharging. Both thepanel and the controller are tested and UL approved. The complete RV Power Kit includes all themounting hardware, wiring and directions you need for a trouble-free and sturdy installation. Onceyour system is installed, you are ready to go anywhere - just add sunlight. All Shell Solar RVPower Kits are backed with a 5-year limited warranty on the charge controller and 25-year on thesolar modules.

Shell Solar RV Power Kits

Shell Solar RV Power Kit 75

SUNW

IZE

SYST

EMS

94 3/03

Dimensions Model Watts Amp-Hrs/Day W x H x D Use For MSRP

RV Power Kit 55 55 12 – 15 51” x 13” x 2.2” DC appliances- $699.00 AM/FM radio, fluorescent lights,ventilation fans

RV Power Kit 55 Expansion (Same specs but does not include 20-Amp controller) $559.00

RV Power Kit 75 75 16-20 48” x 21” x 2.2” DC appliances- $899.00AM/FM radio, fluorescent lights,ventilation fans, TV/VCR


RV Power Kit 110 110 100 / 22-26 52” x 26” x 2.2” DC appliances- $1099.00AM/FM radio, fluorescent lights,ventilation fans, TV/VCR,circulation pumps, microwave,refrigerator



6/01

earthsafe™ Kits

Shell Solar has designed a line of solar power kits to provide an efficient and easy-to-install residential or commercial building system for utility interconnection. These kits meet allNEC requirements and provide anti-islanding as required by many utilities. All earthsafesystem kits consist of Shell Solar SP75 solar modules, universal roof mounting kits, and theAdvanced Energy GC 1000 DC/AC inverter. The GC 1000 includes a string combiner,ground fault protection and a DC disconnect. UL listed.

Shell Solar

Installed earthsafe™ kit

Model DC Power AC Power # of SP 75’s # of Inverters SW Part Number

earthsafe™ 10-6 600 W 500 W 8 1 100ES10-6KITearthsafe™ 10-12 1200 W 1000 W 16 1 100ES10-12KITearthsafe™ 10-18 1800 W 1500 W 24 2 100ES10-18KITearthsafe™ 10-24 2400 W 2000 W 32 2 100ES10-24KIT

earthsafe™ 10 Tilt Kit1 kit required for every 4 modules 100ES10TILTKIT


Documents

Catalog Free