219

6: XXXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: CASTO

RS

CASTORS Castor Selection Always choose the largest wheel diameter that you can. Large wheels help reduce rolling resistance and can cope with rougher surfaces. The wheel types of the castors that Flints stocks are shown on the table below and overleaf.Castor Loading On a platform fitted with four castors take the weight of the platform and the load it is carrying [evenly distributed] and divide by three to take into account uneven surfaces etc. If the platform is carrying actors then you will have to assume the worst case: that the actors will all be standing on one corner of the platform and so EACH castor will have to take the entire load with an added margin for safety.

WD = Wheel DiameterOH = Overall HeightSR = Swivel RadiusTW = Tread WidthTPD=Top Plate Dims

All measurements are in millimetres

TPD

WDOH

SR

Light-Duty Castors This range of industrial castors all have pressed steel top plates with plain bearings. Wheels are polypropylene, or a quiet non-marking rubber tyre on plastic with a steel core. The Swivel Bolt-hole and Swivel Braked Bolt-hole castors have either a 10 mm or 12 mm bolt-hole. Use the Expanders below to fit them to all types of trolley.

Wheel Type For Against Typical Use Polypropylene [PP] Economical and non-marking Too noisy for use during Small items of furniture, small boxes, light performance trucks Grey Rubber Cheap, quiet, non-marking, Light duty use only Light trucks and furniture used during floor protecting performance

Light-Duty Castors WD load [kg] OH SR TW wt [kg] TPD centres offset code price code pricetype PP rubber PP rubber PP rubber median bolt Ø PP rubber Swivel 50 40 50 73 50 20 17 0.20 0.20 50 x 50 35 x 35 10 25 CASLD50NS £3.20 CASLD50RS £3.20Swivel Braked 50 40 50 73 73 20 17 0.22 0.22 50 x 50 35 x 35 10 25 CASLD50NB £3.90 CASLD50RB £3.90Fixed 50 40 50 73 — 20 17 0.19 0.19 50 x 50 35 x 35 10 — CASLD50NF £3.10 CASLD50RF £3.10Swivel Bolt-hole 50 — 40 71 50 — 17 — 0.20 — — 10 25 — — CASLD50RSBT £3.50Swivel Braked Bolt-hole 50 — 40 71 73 — 17 — 0.22 — — 10 25 — — CASLD50RBBT £5.00

Swivel 75 50 50 100 69.5 21 21 0.23 0.33 60 x 60 43 x 43 10 32 CASLD75NS £4.16 CASLD75RS £4.16Swivel Braked 75 50 50 100 90 21 21 0.26 0.35 60 x 60 43 x 43 10 32 CASLD75NB £5.00 CASLD75RB £5.00Fixed 75 50 50 100 — 21 21 0.22 0.32 60 x 60 43 x 43 10 — CASLD75NF £4.00 CASLD75RF £4.00Swivel Bolt-hole 75 — 50 95 69.5 — 21 — 0.30 — — 10 32 — — CASLD75RSBT £5.38Swivel Braked Bolt-hole 75 — 50 95 90 — 21 — 0.32 — — 10 32 — — CASLD75RBBT £6.50

Swivel Bolt-hole 100 — 80 128 88 — 27 — 0.60 — — 12 38 — — CASLD100RSBT £8.13Swivel Braked Bolt-hole 100 — 80 128 105 — 27 — 0.70 — — 12 38 — — CASLD100RBBT £9.00

Inserts for Bolt-Hole Castors These expanders can be fitted to any single bolt-hole castor. Use for round or square tubing on all types of trolley. All the expanders have a 10 mm bolt. The 50 mm and 75 mm Ø bolt-hole castors above have a 10 mm threaded hole and will fit perfectly. Meanwhile, the 100 mm Ø bolt-hole castors above have a 12 mm threaded hole and the 12 mm extender will come as a kit with a reducer washer to ensure a snug fit. Expanders for Bolt-Hole Castors round code price square code price round code price square code pricefits tubes height weight fits 10 mm thread fits 10 mm thread fits 12 mm thread fits 12 mm thread21.5 – 24 90 0.11 CASER24 £3.50 CASES24 £3.50 CASER24K £3.50 CASES24K £3.5024 – 27 90 0.11 CASER27 £3.50 CASES27 £3.50 CASER27K £3.50 CASES27K £3.5027 – 30 90 0.11 CASER30 £3.50 CASES30 £3.50 CASER30K £3.50 CASES30K £3.50

WHEEL DIAMETER

50

WHEEL DIAMETER

75

WHEEL DIAMETER

100

Round Bolt Square Bolt

LIGHT-DUTY CASTORS

50 mm Swivel

75 mm Polypropylene Wheel 75 mm Rubber Wheel

50 mm Swivel Braked 50 mm Fixed 50 mm Swivel Bolt-hole 50 mm Swivel Braked Bolt-hole Top Plate 75 mm Swivel

Expanders for 12 mm Bolt-Hole castors come with a reducer washer.

This pageSpend over £100

Save 15%Spend over £500

Save 20%

220

6: X

XXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: C

AST

OR

S

Revvo Series 4 Pressed steel top plate castors that reliably cope with all but the heaviest of stage loads. Swivel heads have a single ball bearing. Wheels have plain bearings and are either nylon, or a Revvothane tyre on cast iron. The brake locks both wheel and swivel with an easy-to-use foot lever which trails the direction of the travel. Fabricated castors for very heavy duties can be quickly supplied — please phone for a quotation. If you require the wheel and swivel lock to remain in a fixed position please see the Fixed Position Brake Castors [page 224].

Revvo Series 4 WD load [kg] OH SR TW wt [kg] TPD centres code price code price nylon Revvothane nylon Revvothane median bolt Ø nylon RevvothaneSwivel 75 160 175 114 73 35 25 0.95 1.39 135 x 110 105 x 80 10 CAS132 £15.12 CAS131 £30.22Fixed 75 160 175 114 — 35 25 0.53 0.95 145 x 110 105 x 80 10 CAS032 £10.08 CAS031 £24.78

Swivel 100 225 250 139 91 35 29 1.02 1.69 135 x 110 105 x 80 10 CAS140 £16.76 CAS141 £35.41Swivel Braked 100 225 250 139 91 35 29 1.20 1.91 135 x 110 105 x 80 10 CAS140L £31.51 CAS141L £50.16Fixed 100 225 250 139 — 35 29 0.61 1.27 145 x 110 105 x 80 10 CAS040 £11.10 CAS041 £29.74

Swivel 125 250 265 164 105 35 32 2.03 2.50 135 x 110 105 x 80 10 CAS157 £19.84 CAS154 £43.70Swivel Braked 125 250 265 164 105 35 32 2.30 2.78 135 x 110 105 x 80 10 CAS157L £34.59 CAS154L £58.34Fixed 125 250 265 164 — 35 32 1.34 1.89 135 x 110 105 x 80 10 CAS057 £14.14 CAS054 £38.01

WHEEL DIAMETER

75WHEEL

DIAMETER

100WHEEL

DIAMETER

125

REVVO SERIES 4 MEDIUM TO HEAVY-DUTY CASTORS

75 mm Swivel Revvothane 125 mm Swivel Braked Nylon75 mm Fixed Revvothane

Fixed Swivel

MEDIUM TO HEAVY-DUTY CASTORS

Medium to Heavy-Duty Castors WD load [kg] OH SR TW wt [kg] TPD centres offset code price code pricetype nylon PU nylon PU nylon PU median bolt Ø nylon PUSwivel 80 200 200 106 77.5 35 30 0.56 0.90 105 x 85 80 x 60 10 37.5 CASMD80NS £7.88 CASMD80PS £22.50Swivel Braked 80 200 200 106 125 35 30 0.70 1 105 x 85 80 x 60 10 37.5 CASMD80NB £10.50 CASMD80PB £24.48Fixed 80 200 200 106 — 35 30 0.33 0.65 105 x 85 80 x 60 10 — CASMD80NF £7.25 CASMD80PF £20.79

Swivel 100 200 220 128 90 35 38 0.65 2.2 105 x 85 80 x 60 10 40 CASMD100NS £8.25 CASMD100PS £22.86Swivel Braked 100 200 220 128 125 35 38 0.75 2.4 105 x 85 80 x 60 10 40 CASMD100NB £10.88 CASMD100PB £25.20Fixed 100 200 220 128 — 35 38 0.55 1.7 105 x 85 80 x 60 10 — CASMD100NF £7.75 CASMD100PF £21.42

WHEEL DIAMETER

80WHEEL

DIAMETER

100

Medium to Heavy-Duty Castors This range of industrial castors all have pressed steel top plates. The wheels are either nylon with plain bearings, or a tough polyurethane [PU] tyre on cast iron with ball bearings. To decide which one to choose have a look at the table above.

100 mm Swivel 100 mm Swivel Braked 100 mm Fixed 80 mm Nylon Wheel 80 mm Polyurethane Wheel Top Plate 80 mm, 100 mm Swivel

Wheel Type For Against Typical Use Nylon Cheap, very strong, clean, Too noisy for use during Slave trucks, scaffolding castors, heavy-duty non-marking, light performance. storage trolleys not used during performance Polyurethane [Revvothane] Quiet, high tear strength, 10 times the Expensive All uses but especially heavy scenery used on cast iron working life and 3 times the load carrying during performance of rubber, low rolling resistance, excellent recovery from static periods Blue elastic rubber Soft, very quiet, non-marking, Limited range from stock Typically used as flight case castors floor protecting Black rubber on plastic Cheap, quiet, floor protecting, medium-duty May leave marks Medium weight trucks where the budget is tightBlack polyurethane [PU] Soft, very quiet, non-marking, The softer wheel adds a All performance stage use especially when the floor protecting a little rolling resistance wheels may be seen and silence is required

This pageSpend over £100

Save 15%Spend over £500

Save 20%

221

6: XXXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: CASTO

RS

Super Quiet Light-Duty Black Castors The frames are black sheet steel with double ball races in the swivel head. They are fitted with polyurethane tyres on a tough nylon hub with ball bearings giving super smooth running. The wheels are exceptionally quiet and non-marking, even on dance floors. Soft 80A on the Shore scale. The braked version locks both the wheel and the swivel. Available in a single or double wheel version.

4 Non-marking — even on dance floors 4 Great choice for all light loads 4 German manufacturing quality

Super Quiet Black Castors WD max load OH TW weight TDP hole centres offset code priceSingle Wheel Swivel 75 60 kg 100 23 0.38 kg 60 x 60 38 x 38 / 46 x 46 28 CAS7523N £14.45Single Wheel Swivel Braked 75 60 kg 100 23 0.43 kg 60 x 60 38 x 38 / 46 x 46 28 CAS7523NB £15.90Double Wheel Swivel 75 80 kg 100 23 0.62 kg 60 x 60 38 x 38 / 46 x 46 28 CAS7523ND £26.22Double Wheel Swivel Braked 75 80 kg 100 23 0.66 kg 60 x 60 38 x 38 / 46 x 46 28 CAS7523NDB £29.15Single Wheel Fixed 75 60 kg 100 23 0.30 kg 60 x 60 38 x 38 / 46 x 46 28 CAS7523NF £16.45

WHEEL DIAMETER

752x

Low Level 35 mm Black Castors Neat, well-designed theatre castors, attractive enough for other uses like furniture making. Black sheet steel frames with a double ball race in the swivel head for smooth movement. Wheels are black polyurethane on a solid aluminium core with ball bearings. They are a hard-wearing 92A on the Shore scale.

Low Level Black Castors WD max load OH TW weight TDP hole centres offset code priceSwivel 35 100 kg 52 27 0.27 kg 60 x 60 38 x 38 / 47 x 47 15 CAS35KUPL £20.85Swivel Braked 35 100 kg 52 27 0.28 kg 60 x 60 38 x 38 / 47 x 47 15 CAS35KUPLB £29.50Fixed 35 100 kg 52 27 0.23 kg 60 x 60 38 x 38 / 47 x 47 15 CAS35KUPLF £18.60

WHEEL DIAMETER

35

BLACK THEATRE CASTORS

Heavy-Duty Black Euro Castors These tough castors represent fantastic value and would be the perfect choice for the majority of stage uses. The extra tough steel frame is finished in black. The swivel head has double ball races. The wide wheel has black polyurethane tyres on a black cast iron hub with twin ball races. The castor has been developed to be a main workhorse of European theatre stages. Available as a swivel castor or a swivel castor with wheel and swivel brake. They are a hard-wearing 92A on the Shore scale.

4 Real value for a very tough castor — 350 kg loading for well under half the price of lower rated castors4 All-black frame, wheel and tyre 4 Definitive choice for most theatre trucks 4 Assembled in Germany

Heavy-Duty Black Euro Castors WD max load OH TW SR weight TPD hole centres offset code price 20+Swivel 100 350 kg 125 40 95 1.60 kg 140x 110 105 x 80 48 CAS80BEC £20.85 £17.73Swivel Braked 100 350 kg 125 40 145 2.20 kg 140x 110 105 x 80 48 CAS80BECB £28.68 £24.29

75 mm Single Wheel Swivel 75 mm Single Wheel Swivel Braked 75 mm Double Wheel Swivel Braked75 mm Single Wheel Fixed

100 mm Swivel 100 mm Swivel Braked

Super Quiet Black Scene Shifter [up to 240 kg] Choose these units for very quiet and easy moving trucks which will glide silently across the stage. Frame of black sheet steel with double ball races at the swivel head. They are fitted with three sets of twin wheels with polyurethane tyres on a tough nylon hub with ball bearings giving super smooth running. The black wheels have a slightly softer Shore rating than most castors at 80A which not only keeps the noise right down but helps to prevent any marking on dance floors.

4 Super quiet 4 Non-marking 4 Low friction 4 German quality

Super Quiet WD max load OH TW SR weight TPD hole centre code price 75 240 kg 125 2 x 23 381 4.40 kg 105 x 85 80 x 60 CAS7523T £107.95

Hush!Whisper

quiet

WHEEL DIAMETER

75

WHEEL DIAMETER

100

35 mm Swivel 35 mm Swivel Braked 35 mm Fixed

4 Discreet — only 52 mm high 4 Non-marking 4 Hard-wearing 4 German quality

Best value tough theatre

castor

Page updated 191031

222

6: X

XXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: C

AST

OR

SSCENE SHIFTERS [TURTLES]

Low Level Scene Shifter [up to 360 kg] Choose this for heavy trucks which require a low overall height for sightline and access purposes. Top plate with twin wheels with polyurethane tyres on a cast iron hub with plain bearings. This is the same basic unit as the Standard Scene Shifter below but fitted with low level twin wheeled castors.

Low Level WD max load OH SR TW weight code list 50 360 kg 96 154 2 x 14 8.20 kg CAS601 £199.26 £149.08

Mini Scene Shifter [up to 300 kg] Very popular units which are ideal for smaller sized trucks. The smaller swivel radius helps to keep the wheels nearer to the edge of the truck and thus improve the stability. Although reduced in size, these Scene Shifters will take very high loads. Mini 35 mm wheels with polyurethane tyres on plastic hub with ball bearings. 4 Help to improve stability 4 Very low overall height 4 Lightweight

Mini WD max load OH SR TW weight code list 35 300 kg 85 95 28 1.80 kg CASMINISS £109.20 £86.59

Standard Scene Shifter [up to 460 kg] This is the main workhorse of the Scene Shifter series . Fitted with tough but quiet 100 mm wheels with polyurethane tyres on a cast iron hub with plain bearings. Choose this for all general and heavy-duty uses.

Standard WD max load OH SR TW weight code list 100 460 kg 168 218 29 11.80 kg CAS602 £191.27 £143.08

Hebewunder [up to 400 kg] The Hebewunder is the perfect choice of castor to move heavy scenic trucks around the stage. Probably the biggest advantage of using the Hebewunder over braking castors is the fact that the truck will sit firmly on the floor when it is lowered into place. This ensures a well spread load and therefore great stability with no chance of accidental movement. Leaving built scenic pieces on braked castors during performance can result in the floor flexing due to the high point loading. This could translate into “wobbly scenery” from the audience’s point of view or delayed scene changes because of the difficulty to marry up bolt holes or fixings. Each Hebewunder can lift 400 kg by means of compressed air. The triple swivel castors have the advantages of ensuring a minimal offset for easy initial rolling, good

load spreading and excellent track jumping capabilities. The 50 mm castors employed on these units have solid aluminium wheels fitted with bearings and 92° Shore Vulkollan tyres. This allows great load bearing while maintaining a useful low overall height. Flints can supply all the accessories necessary to connect the units, a few are listed below, the rest and more info can be found in the Castors Appendix in the Our Catalogue section of our website.

Hebewunder WD load [kg] OH SR TW wt [kg] TPD holes code price min max width length [includes air supply] centres Ø 50 400 147 188 250 40 9 220 330 180 x 150 11.5 CASHW50 £298.00

Hebewunder Accessories price3-way Valve 1/8” CASHW3W £47.05Air Hose 6x4 25 m CASHWHO £18.64Connector 1/8” CASHWCO £2.14Silencer CASHWSI £2.09T-Connector CASHWTC £4.27

Tradeline

Tradeline

HEBEWUNDER

Scene Shifters [Turtles] These castors solve the various problems that can be encountered when using traditional swivel castors. They permit heavy trucks to change rolling direction, even from stationary, without having to exert the extra effort normally needed to change wheel direction. They allow trucks to enter from the wings, stop centre stage, and leave upstage. The triple wheels also spread the load over a larger stage area reducing the problems caused by high point loads on soft floors. They can really help when trying to align trucks ready for bolting-up when the height inaccuracies, caused by high point loading on spongy stages, often cause delays to scene changes as staff are required to fetch crow bars to level up the trucks. Finally, they make good track jumpers. Flints stocks four types of turtles [see Black Scene Shifter on previous page] and sell them at prices well below list. We also stock the pneumatic Hebewunder lifting castors which allow the scenery trucks to sit firmly on the stage and lift to move.

STANDARD SCENE SHIFTER [HEAVY-DUTY TO 460 KG]

LOW LEVEL SCENE SHIFTER [TO 360 KG]

MINI SCENE SHIFTER [LIGHT-DUTY TO 300 KG]

WHEEL DIAMETER

50

WHEEL DIAMETER

35

WHEEL DIAMETER

100

Tradeline

This gizmo uses compressed air to lift scenery over 40 mm.

3-way Valve 25 m Air Hose T-Connector

Why not take a look at the Castors Appendix: Hebewunder

Castor in the Our Catalogue section of our website?

Tradeline

WHEEL DIAMETER

50

Page updated 190410

223

6: XXXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: CASTO

RS

Low Level Single Wheel Swivel Castor A popular and very useful single bolt-fixing castor with a quiet polyurethane tyre and an overall height of just 59 mm. These are the same wheels used on the Mini Scene Shifter. They are supplied complete with an M10 Allen bolt leaving 20 mm of protruding thread.

Low Level Single Swivel Castors WD load OH SR TW code 35 100 kg 59 33 28 CAS295S

Low Level Twin Wheel Swivel Castors If you need to move heavy weights but have restricted height these tough units with polyurethane tyres on cast iron wheels are ideal. We have now introduced a more economical version with nylon wheels for use when noise is not an issue.

Low Level Swivel Castors WD load OH SR TW codePolyurethane tyre on cast iron 50 160 kg 64 50 2 x 14 CAS295Nylon 50 160 kg 64 50 2 x 14 CAS295N

Flying Saucer [Ball transfer unit] If you can’t even fit in a low level swivel then these may help, but be careful on soft floors as they exert a very high point pressure which can cause damage. The units are really designed to be mounted facing upwards as transfer units for crates and boxes.

Flying Saucer max load OH code price 25 kg 30 CAS710 £3.68

Lo-Line© Very Low Level Heavy-Duty Castor

Every now and again you come across some products of such brilliance that you wonder how you ever managed without them. These castors

designed by the legendary Mike Barnett solve the age-old problem of theatre trucks having to be 150 mm high just

to accommodate decent castors. Now, with a bit of ingenuity, you can build a truck just 40 mm high with a

weight loading on each swivel Lo-Line© unit of up to 350 kg! These ingenious units use 130 mm diameter steel wheels

canted over so that the overall height is just 34 mm. Fitted with special deep grooved ball bearings which are sealed for life. The 16 mm thick top plate can be welded or drilled and tapped to secure the units to your trucks. Available in four types. Copyright: M.Barnett.

4 Solves sightline problems from front row seats 4 Just 34 mm overall height!

4 Great track jumpers4 Use the fixed version along revolve rims

4 Useful for low level slave pallets4 Takes up to 350 kg [175 kg for fixed units]

4 Both wheels together provide a tread width of 70 mm

Fixed Version These units can be used on any truck running in a straight line or on pivot trucks with the units aligned in line with the pivot point. In particular they are perfect for use around the rims of revolves, allowing heavy-

duty revolves, and their surrounds, to be very low profile sometimes enabling the front row to actually see the floor! Also available in a quieter version with replaceable nylon inserts.

Lo-Line© Fixed code price max load WD OH TW wt

175 kg 130 34 35 1.25 kg CASMBLLCF £60.35Nylon insert version 175 kg 130 34 35 1.25 kg CASMBLLCNF £91.60

Swivel Version For all stage use. Also available in a quieter version with replaceable nylon inserts in the wheels.

Lo-Line© Swivel code price max load WD OH SR TW wt

350 kg 130x2 34 140 70 4.25 kg CASMBLLC £199.00Nylon insert version 350 kg 130x2 34 140 70 4.25 kg CASMBLLCN £249.00

LOW LEVEL CASTORS

Sheer genius, creative ingenuity

Polyurethane on cast iron CAS295 List £35.14 our price £29.00 Nylon wheels CAS295N List £18.69 our price £15.89

TRADELINE

Low Level Single Wheel CAS295S List £12.00 our price £9.99TRADELINE

Front view of the swivel version.

Top view of the fixed version. For Dollies and Material Handling Products see our special section, pages 337 — 338

This characterful Icelandic Tractor has a lovely set of wheels but they may be a little bit noisy.

Upside down view of nylon version.Top view of the swivel version

WHEEL DIAMETER

35

WHEEL DIAMETER

50

Tradeline

Tradeline

224

6: X

XXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: C

AST

OR

S

Flight Case Castors These rugged top quality castors have blue elastic rubber tyres which are quiet and non-marking. Ideal for flight cases but also useful whenever noise is a concern. Fitted with roller bearings. *NB: The fixed version has a 3 mm height difference.Top plate: 105 x 80 mm. Bolt centres: 80 x 60 mm. Fixings: 4 off M8.

Flight Case Castors max load WD OH SR wt code priceSwivel 150 kg 100 125 85 460 g CAS3470 £9.50Swivel braked 150 kg 100 125 85 460 g CAS3477 £10.95Fixed 150 kg 100 128* 85 460 g CAS3478 £8.75

F ixed Pos i t i on Brake Castor Generally, the foot-operated brakes on swivel castors swivel with the wheel so they trail the direction of travel. If the wheels are easily accessible this is not generally too

much of a problem, especially if only two brakes are needed. However, stage trucks are generally designed to hide the castors from the audience making access to the brakes very difficult. If the truck needs positioning in view of the

audience it can get messy! These castors are designed to avoid this familiar problem. The

foot-operated lever brake will lock off both the wheel and swivel but it remains fixed to the top plate. Your carpenters or metal fabricators will be able to position the castor so the lever neatly protrudes from the rear of the truck. A little bit of luminous tape on the lever and your trucks can be swiftly locked off even in a quick blackout. German manufacture. Top plate size: 135 x 105 mm. Bolt centres: 105 x 80 mm. 88° Shore.

Fixed Brake Castor max load WD OH SR wt code price 250 kg 80 125 85 2.25 kg CASFPB £103.95

Plate Skates These useful devices will grip panels up to 56 mm thick and take loads of 250 kg on their strong 150 mm Ø wheels. Ideal for moving heavy flattage or sheets of ply from lorries or around stage. Just use one in the centre of the panel and the crew can manoeuvre heavy items with ease.

Dimensions can be found on page 337.

Plate Skates max load WD OH TW wt code price 250 kg 150 225 40 4.20 kg CASPS15056 £60.90

Nylon Rollers A useful range of small but heavy-duty nylon rollers. For convenience each size has the same hub width and diameter bore. The rollers are fitted with two ball races with side shields making them

very free-running and quiet. The special feature is that they can be ordered with either a plain face, a V groove, or a round groove. Ideal for constructing heavy-duty travellers, small lifts, under-

stage tracking, etc. The V-grooved rollers will run smoothly on inverted angle iron tracks. Trucks will self-centre if there is any width discrepancy between the tracks whereas flanged wheels running on square tracks may bind and screech.

Nylon Rollers WD bore hub width wt code pricePlain 50 10 25 80 g FHSN050P £12.95Round groove 50 10 25 60 g FHSN050R £12.95V groove 50 10 25 60 g FHSN050V £12.95

See also Black Nylon Bow Rollers on page 199Counterweight Cradle Roller 38 mm Ø runner in acetal with a quiet polyurethane tyre. 1/2” plain bore. 18 mm tread width. Counterbored one side only to 3 mm deep x 23.8 mm diameter. Fits many Hall Stage cradles.

Counterweight Roller WD bore TW code price 38 1/2” 18 CASCCR £6.04

FIXED POSITION BRAKES

ROLLERS

PLATE SKATES

Scaffold Castors Flints stocks the versatile plug type scaffold castors which are suitable for converting steel rostra into slave trucks [with the addition of a short scaffold sleeve if going directly into the rostra corner post]. Fitted with strong nylon wheels. The unbraked versions are fitted with a wind-in bolt to prevent the wheel from turning when positioned. The much preferred braked versions are fitted with an easy to use kick-down wheel and swivel lock. NB: Due to manufacturing tolerances on the plug and the tube, the castor can sometimes be a slack fit.Conversion Sleeve A 127 mm length of scaffold tube to convert the plug to fit the corner posts of Steeldeck/Megadek rostra systems. Not needed when the castors are mounted on scaffolding legs.Conversion Sleeve code price SCF092 £1.10

Scaffold Castors max load WD OH [ex plug] plug sizes SR TW wt code list priceUnbraked 225 kg 125 159 ex plug 64 x 38.35 105 35 1.26 kg CAS313 £34.74 £28.41Braked 225 kg 125 159 ex plug 64 x 38.35 105 35 1.80 kg CAS313L £42.87 £35.08Braked 500 kg 150 200 ex plug 127 x 38.1 129 45 3.90 kg CAS314L £84.43 £68.93Unfortunately these castors have been discontinued by the current manufacturer, and there is no remaining stock of the unbraked 500 kg version. We are currently resourcing them so check back!

FLIGHT CASE CASTORS

SCAFFOLD CASTORS

Now black!

Runner-up ABTT Widget of the Year 2013

A problem solved!

Set of great flight case castors for

£30.90

125 mm Braked version with foot operated lever.

125 mm Unbraked

version with wind-in bolt.

WHEEL DIAMETER

100

WHEEL DIAMETER

80

WHEEL DIAMETER

125WHEEL

DIAMETER

150

Fits directly into standard scaffold tube

WHEEL DIAMETER

50

WHEEL DIAMETER

38

WHEEL DIAMETER

150

Buy set of four — two swivel & two braked

CAS347K £30.90 TRADELINEF

Page updated 191031

225

6: XXXX

Unit 9 Deptford Trading Estate, Blackhorse Road, London, SE8 5HYT: 020 7703 9786 www.flints.co.uk

6: CASTO

RS

Standard UJA1 Castor Unit Fitted with a 50 mm twin-wheel castor and suitable for most applications. It is recommended that this is installed with a 10 mm clearance between the floor and castor so that the foot pedal is at the most efficient part of its travel as it starts to lift. This gives 24 mm of ground clearance to the piece you are moving. If lightweight pieces are to be moved, then

clearance may be reduced to give more lift. This unit may be fitted with the UJA5 stud set and locking catch to create a lift off UJA1/5.

Triple E Unijack SWL code price50 mm twin-wheeled castor 160 kg UJA1 £150.00

Standard UJA2 Castor Unit Fitted with an 80 mm single-wheel castor. The internal mechanism is the same as the UJA1 but has a larger body in order to accommodate the larger castor and may therefore be used with heavier loads. It is recommended that this is installed with the same 10 mm clearance as the UJA1 above. This unit may be fitted with

the UJA5 stud set and locking catch to create a lift off UJA2/5.Triple E Unijack SWL code price

80 mm Castor 200 kg UJA2 £170.00

Standard UJA3 Brake Unit With the same body as the UJA1 but fitted with a rubber brake foot designed to hold a stage truck in position by lifting a fixed castor from the floor. The unit should be fitted so that it only lifts the fixed castor with a minimum clearance. The brake foot may be purchased separately [UJA8] to convert a UJA1 to a UJA3. This unit may be fitted with the UJA5

stud set and locking catch to create a lift-off UJA3/5.

Triple E Unijack SWL code priceRubber Foot Brake 275 kg UJA3 £135.00

UJA5 Stud Set All the Unijacks can simply be bolted to your scenery but the big advantage of fitting a UJA5 Stud Set to your Unijacks is that one set of Unijacks can be used on many pieces of scenery. The scenery will need to be fitted with a UJA6 receiving keyplate .UJA6 Keyplate These need to be fitted to your scenery to accept Unijacks fitted with the UJA5 Stud Sets. UJA8 Spare Rubber Foot to convert UJA1/UJA2 to UJA3, or replace worn feet.

Triple E Unijack code priceStud set for use with Unijacks UJA5 £35.00Keyplates UJA6 £25.00Spare rubber UJA8 £10.00

Turntables A range of ball-bearing turntables ideally suited for securing revolve centres to the stage but also handy for constructing stage trucks and for revolving platforms for heavy sculptures. The flanges are undrilled. Measurements in mm.

Turntables max load ØA ØB ØD H G wgt code price 750 kg 400 342 230 45 8 11 kg CAS400L £237.15 900 kg 500 442 330 45 8 15 kg CAS500L £263.45

Other sizes are available to order.

Lazy Susans These lightweight ball race rings are designed for maximum stability and smooth running. They are suitable for props and special effects. Zinc-plate finish. For heavy scenery applications choose the turntables listed left . No one really knows why they are called Lazy Susans but the first written reference was in an advert in Vanity Fair in December 1917.

Lazy Susans max load Ø/width OH code priceRound 450 kg 300 mm 10 mm CAS300LS £10.80Square 225 kg 150 mm 10 mm CAS150LS £5.27Square 130 kg 100 mm 10 mm CAS100LS £3.50

TURNTABLES

TRIPLE E UNIJACKS

B

G

H

D

A

Triple E Unijack™The Unijack™ system was the major building block in the Triple E range when the company started. Now several thousand Unijacks™ later it is still doing the work it was designed for on stages throughout the world. The system comprises the basic lifting unit with a range of accessories that allow easy handling of heavy scenery. Designed originally for scenic trucks on theatre stages, they can also be used for all types of industrial equipment, machinery, workbenches, display cabinets and counters. All can be moved or braked with confidence.

Registered Design No. 1032215 Registered Trademark No. 1302\376.

50 mm Twin-Wheeled Castor

With a rubber foot brake

80 mm Single Wheel Castor

Stud set and key plate

WHEEL DIAMETER

50

WHEEL DIAMETER

80

WHEEL DIAMETER

50

Tradeline

Page updated 200212