Embed Size (px)
Citation preview
Op
era
tor’
s M
an
ua
l
Operator’s Manual
THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF
J.I. CASE OR IT’S SUCCESSORS. J.I. CASE AND IT’S SUCCESSORS
ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY OF THIS MANUAL.
TRADE MARKS AND TRADE NAMES CONTAINED AND USED HEREIN ARE THOSE OF OTHERS,
AND ARE USED HERE IN A DESCRIPTIVE SENSE TO REFER TO THE PRODUCTS OF OTHERS.
430, 431, 435, 440, 441,
445, 530, 531, 535, 540,
541 & 545
CA-O-430,530
Make: Ji Case Model: 430 Years Made: 1960-1969 Make: Ji Case Model: 470 Years Made:
1970-1973
HP-PTO: 34 HP-Engine: HP-Drawbar: HP-PTO: 34.3 HP-Engine: HP-Drawbar: Year Beginning Serial Number
HP-Range: 34 Engine-Make: CASE
Engine-Fuel: DIESEL HP-Range: 34 Engine-Make:
CASEEngine-Fuel: DIESEL 1960 3012275
Engine-Cyl(s)-CID: 4/188
Transmission-STD: Optional: Engine-Cyl(s)-
CID: 4/188Transmission-STD: Optional: 1960 6144001
Fwd/Rev Standard: 4/1
Fwd/Rev Optional: 8/2 Mfwd-Std/Opt: Fwd/Rev
Standard: 8/2Fwd/Rev Optional:
Mfwd-Std/Opt: 1961 816880
Tires-Std Front: Tires-Std Rear: Wheelbase-
Inch: Tires-Std Front: Tires-Std Rear: Wheelbase-Inch: 1961 6162601
Pto Type: Pto Speed: 540 CAT I-3pt Hitch: True Pto Type: Pto Speed: 540 CAT I-3pt
Hitch: True 1962 8190001
CAT II-3pt Hitch: False
CAT III-3pt Hitch: False Hitch Lift: CAT II-3pt Hitch:
FalseCAT III-3pt Hitch: False Hitch Lift: 1963 8208001
Hydraulics-Type: Hyd-Cap: Hyd-Flow: 8.5 Hydraulics-Type: Hyd-Cap: Hyd-Flow: 8.5 1964 8229001
Hyd Std Outlets:
Cooling Capacity: 16.5
Fuel Tank Capacity: 13 Hyd Std Outlets: Cooling
Capacity: 16.5Fuel Tank Capacity: 13 1965 8253501
Cab-Stdm A/C; Rops: Weight: 3710 New Price: 4389 Cab-Stdm A/C;
Rops: Weight: 3560 New Price: 0 1966 8279001
1967 8306501
Make: Ji Case Model: 530 Years Made: 1960-1969 Make: Ji Case Model: 570 Years Made:
1970-1973 1968 8332101
HP-PTO: 41.2 HP-Engine: HP-Drawbar: HP-PTO: 35.5 HP-Engine: HP-Drawbar: 1969 8356251
HP-Range: 41 Engine-Make: CASE
Engine-Fuel: DIESEL HP-Range: 36 Engine-Make:
CASEEngine-Fuel: GAS
Engine-Cyl(s)-CID: 4/188
Transmission-STD: Optional: Engine-Cyl(s)-
CID: 4/159Transmission-STD: Optional:
Fwd/Rev Standard: 12/3
Fwd/Rev Optional: Mfwd-Std/Opt: Fwd/Rev
Standard: 12/3Fwd/Rev Optional:
Mfwd-Std/Opt: Year Beginning Serial
Number
Tires-Std Front: Tires-Std Rear: Wheelbase-
Inch: Tires-Std Front: Tires-Std Rear: Wheelbase-Inch: 1970 8650001
Pto Type: Pto Speed: 540 CAT I-3pt Hitch: True Pto Type: Pto Speed: 540 CAT I-3pt
Hitch: True 1971 8674001
CAT II-3pt Hitch: False
CAT III-3pt Hitch: False Hitch Lift: CAT II-3pt Hitch:
FalseCAT III-3pt Hitch: False Hitch Lift: 1972 8693001
Hydraulics-Type: Hyd-Cap: Hyd-Flow: 8.5 Hydraulics-Type: Hyd-Cap: Hyd-Flow: 9.3 1973 8712001
Hyd Std Outlets:
Cooling Capacity: 16.5
Fuel Tank Capacity: 22 Hyd Std Outlets: Cooling
Capacity: 14Fuel Tank Capacity: 22 1974 8736601
Cab-Stdm A/C; Rops: Weight: 3600 New Price: 5640 Cab-Stdm A/C;
Rops: Weight: 3910 New Price: 5691 1975 8770001
Paint Codes
Location MFG Color Name
RIMS ALUMINUMBODY POWER RDHOOD & FENDER POWER WHITE
PLATE FASTENED TO INSTRUMENT PANEL 430 & 530
LEFTHAND SIDE, ABOVE PLATFORM FLOOR, NEXT TO STEERING WHEEL 470 & 570
Figure 1. Low Center King Tractor
Figure 2. Standard Tractor w/Grove Fenders
2
Compiled and Reproduced From Original by Jensales Inc.
SPECIFICATIONS
General
Type --------------------- "Case "Open <Chamber Combustion-4 Cyl. - Valve in Head.
Firing Order -------------------------------------- 1-3-4-2 Cylinder Bore -------------------'."'---------..------ 3-13/16" Stroke ___________________________ .:, __ .;;.,-;;. ______________ 4-1/8"
Piston Displacem,3nt _..,_.,. ________________ .;. _________ 188 Cu. In.
Compression Ratio ---~-·-,--------------------------- 17 .5 to 1 *Valve Clearance (Int~ and Exhaust) ------------- .014 (Hot) Cylinder Sleeves ------------------------- Wet Type Replaceable Engine Idle Speed------------------------------------ 600 RPM Full Load Speed {430 Series) ------------------------ 1750 RPM Full Load Speed (530 Series) Standard Clutch --------- 1900 RPM Full Load Speed (530 Series) Case-o-Matic -------- 2100 RPM No Load Speed (430 Series) ------------------------ 1900 RPM No Load Speed (530 Series) Standard Clutch ---------, 2060 RPM No Load Speed (530 Series) Case-0-Matic---------- 2250 RPM Air Cleaner ------------------------------------ Oil Bath Type Cold Weather Starting Aid ---- Electric Heater - Manifold Type Fuel Recommendation ---------------------- No. 2 Diesel Fuel
Piston and Connecting Rods
Compression Rings--------------------------------------- 2
Oil Rings------------------------------------------------ 1 Piston Pins ----------.---:::.:. __________ ..,___ Full Floating Type Connecting Rod Bearings ...;:.::::..:: ______________ Replaceable Precision
Main Bearings
Steel Back Aluminum Liners.
Number of Main Bearings --------------------------------- 5 Type Bearings -------------------------- Replaceable Precision
Steel Back Aluminum Liners.
*Hot Settings Are Made At Low Idle After the Engine has O~"'rated At Thermostat Control Temperature For at Least Fifteen Mn111tes.
5
Compiled and Reproduced From Original by Jensales Inc.
HYDRAULIC STEERING SYSTEMS
Change Interval -------------------- 1000 Hours (more often in severe dust conditions) .
A replaceable filter element is provided in the reservoir, Figures 11 and 12.
Pump Mounted Reservoir NOTl On gasoline tractors it requires removal of the distributor. Refer to Page 97 for timing of the distributor.
RESERVOIR SHELL "0" RING
Figure 11
/11/IOR'TA/ITBefore removing reservoir shell, mark both shell and pump body, Figure 13 - When installing shell, make sure marks are aligned. This is to insure a good seal and correct oil level reading on dipstick.
To replace filter element, remove acorn nut, seal, shell, special hex.nut, spring and retainer. Remove filter element. Install new element, retainer, spring and special hex.nut. Compress the spring from the outside of the special hex.nut to the shell flange on the pump body to 4-15/16". See inset, Figure 11. Install "0" ring, shell, seal and acorn nut. Refer to Page 32 for filling and bleeding system.
Remote Mounted Reservoir Remove right hand grille
screen. Remove cover, bolt, seal and gasket. Remove filter element, Figure 12.
Install a new element and cover gasket. Install cover, seal and bolt. Refer to Page 32 for filling and bleeding system.
COVER
Figu~§ 12
31
Compiled and Reproduced From Original by Jensales Inc.
TORQUE TUBE AND CONVERTER UNIT DRAIN
Drain and refill the torque tube and converter every 1000 hours of operation, or once a season, whichever occurs first.
PLUG TORQUE TUBE HOUSING
Figure 20
To drain the torque tube and converter unit remove the two 1/2" pipe plugs, see Figure 20 and allow the oil to drain for several minutes. Then use a 3/16" Allen wrench to remove 1/4" plug(A) from the converter turbine housing and the 1/ 4" plug (B) from dual range housing. (Be extremely careful not to drop either of these plugs off the end of the Allen wrench when extracting them from the holes in the bottom of the torque tube.) It will be necessary to have an assistant turn the engine over slowly while you observe the lining up of the drain plug(A) with the drain hole in the torque converter housing.
NOTE Because of the nature of this draining procedure, it may be advisable to have your Case Dealer do this work while he is performing the seasonal servicing of your tractor.
35
Compiled and Reproduced From Original by Jensales Inc.
Stop and Tall Lights Wiring Diagram
RED TAIL LIGHTS
WIRE COLOR CODE
NO COLOR FROM TO
1 WHITE KEY SWITCH STOP LIGHT SWITCH
2 WHITE STOP LIGHT SWITCH STOP LIGHT
3 BLACK LIGHT SWITCH TAIL LIGHT
TABLE OF CONTENTS
SERIAL NUMBERS . . . . . . . • . . . . . . . . . . . . . • . . . 4
MODEL DESIGNATIONS ..•.......•.......•... 4
DIESEL ENGINE SPECIFICATIONS •.......•.•.•. 5-6
148 SPARK IGNITION ENGINE SPECIFICATIONS .... 7-8
159 SPARK IGNITION ENGINE SPECIFICATIONS. ... 9-10
GENERAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . 11 Cooling System. . . . . • . . . . . . . . . . . . . . . . . . . 11 Electrical System . . . . . . • . . . . . . . . . . . . . . . . 11 Brakes ........... ., ........ · .... · . .. . · 11 Case-0-Matic Drive . . . . . . . . . . . . . . . . . . . . . 11 Standard Clutch. . . . . . . . . . . . . . . . . . · . · . · · · 12 Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power Take-Off . . . . . . . • . . . . . ..•.•. • . • . · 12 Belt Pulley . .. . . . . . . . . . . . . . . . . . .. . . . . . . . 12
102
Compiled and Reproduced From Original by Jensales Inc.
TABLE OF CONTENTS (continued)
GENERAL SPECIFICATIONS (Continued) Drawbar .............................. 12 Hydraulic System ........................ 13 Draft-0-Matic System ......•.............. 13 Overall Measurements. . . . . . . . . . . . . . . ..•... 14 Tire and Wheel Equipment . . . . . . . . . . . . . . . . . . 15
FRONT WHEEL TREAD SPACING ............... 16
REAR WHEEL TREAD SPACING ............• , , . 17
TRAVEL SPEEDS .... · · . • · · · • · · · · · · · · , · · · 18-19
FUEL SPECIFICATIONS. · · · · · · · · · · · · · · · · · · · · · 20 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . · · · · · · 20 Diesel. . . ft • .. • • • • • • • • • • • .. • • • • • • • • • • • - .. - 21 Fuel Conditioner. . . . . . • . . . . . . . . .. . • . . • · . • • 22
LUBRICATION ............ , ... , · • · , · · · · · · · · 23 Recommendations and Capacities. . . • . . . . • • · . · · 24 Lubrication Chart . . . . . . . • . . . . . . . . . . . · .. 24-25 Engine Lubrication ........•.....•... · · · 26-27 Engine Oil Filter. . . . . . . • . . • . . . . . . · .. · · · · · · 28 Air Cleaner . . . . . . . • . . . . . . . . . . . . . . . · · . 29-30 Hydraulic Steering System . . . . • . . . . . . . . ... 31-32 Hydraulic System Oil Filter • . . . . . . . . . .... , •. 33 Case-0-Matic Oil Filter .........•....•... , . 34 Torque Tube Drain and Breathers . . . . . . . . . · · 35-36 Repacking Front Wheels ............•. · · · · · • 37
SAFETY PRECAUTIONS, ..• · · · · · · • · · • · · • · · · 38-39 Towing . . . .. . . . . . . . . . . . · · . · · · · · · · .. · · · · · 39
OPERATING INSTRUCTIONS .... · ... · . · · · · · · · · · 40 Ru.n-In Procedure ....................... · 40 Pre-Starting Check List. • . . . . . . . • . . . • • • . . . . 41 Operating Controls and Instruments . . . . . . . 42 thru 51 Starting Procedure ....•...... · · · · • · · • · · • · 52 Stopping Procedure . . . . . . . . . . . · • · · · . · · · · · · 52 Cold Weather Operation .........•.•. · · · · · 53-54 Cold Weather Starting Procedure .......... · . 55-56 Case-0-Matic Drive Operation .......... 57 thru 59 Power Take-Off . . . . . . • . . . • • • • • • · • · • 60 thru 62 PTO Operating Precautions . . . . . . . . . .. · • · · · · 63 Drawbar . . . . . . . . . .. . · . · · · · · · · · · · · · · · · · · 63
103
Compiled and Reproduced From Original by Jensales Inc.
TABLE OF CONTENTS (continued)
OPERATING INSTRUCTIONS (Continued) Belt Pulley. . . . . . . . . . . . . . . . . . . . . . . . • . . 64-65 Case Draft-0-Matic Operation ..... · · ... · · · 66-67 Case Draft-0-Matic Adjustments ... ·~· ...... 68-69 Draft Arm Mechanical Floatation . . . . • . . • . . . . . 70 Remote Hydraulic Control Operation . . . . . . • . • . • 71 Portable Cylinders . . . . . . . . . • . . . . . . . . . . • 72-73 Differential Lock . . . . . . . . . . . . . . . . . . . . . . . . 74 Adjustable Front Axle Adjustment ....•........ 75 Power Shift Rear Wheel Adjustment . • . . . • . . . • . . 76 Manual Shift Rear Wheel Adjustment . . . . . • . . . . . 77 Wheel and Front End Weights . . . . . • . . . . . . . • . . 78 Tire Liquid Weight ............... · .• · · · · · 78
PREVENTIVE MAINTENANCE . . . . . . • · · • · . • · · · · 79 Cooling System . . . . . . . . • . . . . . . . • . . . • · • 80-81 Thermostat Replacement • . • . . . . . . . . . • . . . . 81-82 Fan Belt Adjustment . . . . . . . . . . · · · · · · · · · · · · 82 Cleaning the Cooling System . . . . . . . . · . · . · · · · • 83 Diesel Fuel System . . . . · . · · . · · · · · · · · · · · · 84-85 Bleeding Diesel Fuel System. · · . · · • · · · · · · · · · · 86 Servicing Diesel Fuel Filters .... · · · • · • · · · · · · 87 Gasoline Fuel System. . . • . . . . . . · · · · · · · · · · · · 88 Carburetor. .. . . . . . · · · · · .. · · · · · · · · · · · · · · 88-89 Adjusting Differential Brakes . • . . • · · • · · · · · · · · 90 Standard Foot Clutch Adjustment • . · · · • · · · · · · · · 91 PTO Clutch Adjustment .•...... · · · · · · · · · • · · 92 Neutral Start Switch Adjustment .. • . · · · · • · · · · · 93 Spark Ignition System Engines ........•. · ..... 94 Spark Plugs . . . . . . , . . . . ,, . . · . · · · · · · · · · · · · 94 Distributor . . . . · . . • . . · . · · • · · · · · · · , · · · 95-96 Setting Ignition Timing ....•.... · · · · · · · • • · · · 97 Electrical Sy stem . • . . . . • · · · · · · · · · • • · · · · · · 98 Headlights . .. . . . . . . . . . . . . . p • - • • • • • • • • • • • 98 Instrument Panel Lights . . . . . . • . . . . . . . . . · · · · 98 Rear Light . . . . . · . . . ., . · · · .. · · - · · · · · · · · · · · 99 Rear Stop and Tail Lights . . . . . . . . . • · • · · · ., · ~ · 99. Batteries . . · . · · · · · · • · • · · · · · · · · · • · 100 thru 1ai Stop and Tail Light Electrical System • • , ~ , ~ -·; ~ -~ lfi~
104
Compiled and Reproduced From Original by Jensales Inc.
