CARBON SHEET - Alro Steel ASTM A1011 CS TYPE B HOT ROLLED SHEETS HOT ROLLED PICKLED & OILED SHEETS A prime quality low carbon sheet suitable for …

6-1

Alro warehouses use state-of-the-art equipment for handling orders.

CARBON SHEET

HOT ROLLED SHEETS/PICKLED & OILED

HR Sheets/Pickled & Oiled ...............................6-2 thru 6-4 HSLA Sheets .....................................................6-2 thru 6-4 SCS Sheet ........................................................6-2 thru 6-4

COLD ROLLED SHEETS.........................................6-4 thru 6-5

GALVANIZED SHEETS ............................................6-6 thru 6-7

GALVANNEALED SHEETS .................................................. 6-8

ALUMINIZED SHEETS ......................................................... 6-9

SHEARED SHEET BLANKS ................................................. 6-9

TOLERANCES .................................................................... 6-10

6-2

ASTM A1011 CS TYPE B HOT ROLLED SHEETSHOT ROLLED PICKLED & OILED SHEETSA prime quality low carbon sheet suitable for forming, punching, welding, etc. Sheets will be furnished in standard mill edge unless sheared edge is specified.Hot rolled sheets are commercial quality and in most sizes temper flat to improve flatness and relieve internal stress.

HIGH-STRENGTH-LOW-ALLOY (HSLA) SheetsSPECIFICATION: HR A1011 HSLA-F Temper Flat *GR 60 *16 ga is GR 50

Continued on next page

Gage

Nominal Thickness Decimal (inches)

A1011CSB

A1011CSBP&O

Size(inches)

Est. Wt.Per

Sq. Ft.(lbs.)

Est. Wt.Per

Sheet(lbs.)

A1011 HSLA-F GR 60 SCS

High Strength Sheet Steels have higher strength properties along with improved form-ability, weldability and/or atmospheric corrosion resistance than normally obtained from conventional carbon sheet steels. These desirable properties are obtained through selected chemical composition and controlled mill processing.High strength steels lend themselves to applications where weight reduction is a major factor.

SCS (Stretched Clean Surface) HR SheetSCS is a patented process where the material is stretcher leveled, producing a dead flat product. After the material is stretched flat, it is brushed to remove the upper 2 layers of scale leaving a smooth, clean surface. The final layer of scale, which is left on the sheet, will inhibit rust without the need for oil. It can even be painted without the costly clean up required for pickled and oiled.

6 48 x 96 0.1943 8.125 260.00 X 48 x 120 0.1943 8.125 325.00 X 7 36 x 96 0.1793 7.500 180.00 X X 36 x 120 0.1793 7.500 225.00 X X 36 x 144 0.1793 7.500 270.00 X X 48 x 96 0.1793 7.500 240.00 X X X 48 x 120 0.1793 7.500 300.00 X X X 48 x 144 0.1793 7.500 360.00 X X 60 x 96 0.1793 7.500 300.00 X X 60 x 120 0.1793 7.500 375.00 X X 60 x 144 0.1793 7.500 450.00 X X 72 x 96 0.1793 7.500 360.00 X X 72 x 120 0.1793 7.500 450.00 X X 72 x 144 0.1793 7.500 540.00 X X 72 x 240 0.1793 7.500 900.00 X 8 48 x 96 0.1644 6.875 220.00 X X 48 x 120 0.1644 6.875 275.00 X X 60 x 120 0.1644 6.875 344.00 X X X

HOT ROLLED SHEETS/HOT ROLLED PICKLED & OILED SHEETS

6-3



SCSGage


A1011CSBP&O

Size(inches)

Est. Wt.Per

Sq. Ft.(lbs.)

Est. Wt.Per

Sheet(lbs.)

A1011 HSLA-F GR 60

9 48 x 96 0.1495 6.250 200.00 X X 48 x 120 0.1495 6.250 250.00 X X10 36 x 96 0.1345 5.625 135.00 X X 36 x 120 0.1345 5.625 168.75 X X 36 x 144 0.1345 5.625 202.50 X X 48 x 96 0.1345 5.625 180.00 X X X 48 x 120 0.1345 5.625 225.00 X X X 48 x 144 0.1345 5.625 270.00 X X 60 x 96 0.1345 5.625 225.00 X X 60 x 120 0.1345 5.625 281.25 X X 60 x 144 0.1345 5.625 337.50 X X 72 x 96 0.1345 5.625 270.00 X X 72 x 120 0.1345 5.625 337.50 X X 72 x 144 0.1345 5.625 405.00 X X 72 x 240 0.1345 5.625 675.60 X 96 x 240 0.1345 5.625 900.80 X11 36 x 96 0.1196 5.000 120.00 X X 36 x 120 0.1196 5.000 150.00 X X 36 x 144 0.1196 5.000 180.00 X X 48 x 96 0.1196 5.000 160.00 X X X 48 x 120 0.1196 5.000 200.00 X X X 48 x 144 0.1196 5.000 240.00 X X 60 x 96 0.1196 5.000 200.00 X X 60 x 120 0.1196 5.000 250.00 X X 60 x 144 0.1196 5.000 300.00 X X 72 x 96 0.1196 5.000 240.00 X X 72 x 120 0.1196 5.000 300.00 X X 72 x 144 0.1196 5.000 360.00 X X 72 x 240 0.1196 5.000 600.00 X X X 96 x 240 0.1196 5.000 800.00 X 12 36 x 96 0.1046 4.380 105.12 X X 36 x 120 0.1046 4.380 131.40 X X 36 x 144 0.1046 4.380 157.68 X X 48 x 96 0.1046 4.380 140.16 X X X 48 x 120 0.1046 4.380 175.20 X X X 48 x 144 0.1046 4.380 210.24 X X 60 x 96 0.1046 4.380 175.20 X X 60 x 120 0.1046 4.380 219.00 X X 60 x 144 0.1046 4.380 262.80 X X 72 x 96 0.1046 4.380 210.24 X X X 72 x 120 0.1046 4.380 262.80 X X X 72 x 144 0.1046 4.380 315.36 X X X 72 x 240 0.1046 4.380 525.60 X X X13 48 x 96 0.0897 3.750 120.00 X X 48 x 120 0.0897 3.750 150.00 X X

A1011CSB

6-4Continued on next page

10 36 x 96 0.1345 5.625 135.00 36 x 120 0.1345 5.625 168.75 48 x 96 0.1345 5.625 180.00 48 x 120 0.1345 5.625 225.00 48 x 144 0.1345 5.625 270.00 60 x 120 0.1356 5.625 281.50

COLD ROLLED SHEETSCommercial QualityThese sheets are rolled to a close thickness tolerance and possess a fine surface finish. Cold Rolled Sheets are suitable for stamping, forming and moderate drawing operations. Very desirable nickel or chrome plating results can be secured. Also, Cold Rolled Sheets provide an excellent base for baked enamel and lacquer finishes.

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)

SCSGage


Size(inches)

Est. Wt.Per

Sq. Ft.(lbs.)

Est. Wt.Per

Sheet(lbs.)

A1011 HSLA-F GR 60

14 36 x 96 0.0747 3.125 75.00 X X 36 x 120 0.0747 3.125 93.75 X X 36 x 144 0.0747 3.125 112.50 X X 48 x 96 0.0747 3.125 100.00 X X X X 48 x 120 0.0747 3.125 125.00 X X X X 48 x 144 0.0747 3.125 150.00 X X X 60 x 96 0.0747 3.125 125.00 X X X 60 x 120 0.0747 3.125 156.25 X X X 60 x 144 0.0747 3.125 187.50 X X X 72 x 96 0.0747 3.125 150.00 X 72 x 120 0.0747 3.125 187.50 X 72 x 144 0.0747 3.125 225.00 X16 36 x 96 0.0598 2.500 60.00 X X 36 x 120 0.0598 2.500 75.00 X X 36 x 144 0.0598 2.500 90.00 X X 48 x 96 0.0598 2.500 80.00 X X X X 48 x 120 0.0598 2.500 100.00 X X X X 48 x 144 0.0598 2.500 120.00 X X X 60 x 96 0.0598 2.500 100.00 X X X 60 x 120 0.0598 2.500 125.00 X X X 60 x 144 0.0598 2.500 150.00 X X X

18 48 x 96 0.0478 2.000 64.00 X X 48 x 120 0.0478 2.000 80.00 X X


A1011CSBP&O

A1011CSB

6-5

11 36 x 96 0.1196 5.000 120.00 36 x 120 0.1196 5.000 150.00 48 x 96 0.1196 5.000 160.00 48 x 120 0.1196 5.000 200.00 48 x 144 0.1196 5.000 240.00 60 x 120 0.1196 5.000 250.0012 36 x 96 0.1046 4.380 105.12 48 x 96 0.1046 4.380 140.16 48 x 120 0.1046 4.380 175.20 48 x 144 0.1046 4.380 210.24 60 x 120 0.1046 4.380 219.0013 48 x 96 0.0897 3.750 120.00 48 x 120 0.0897 3.750 150.0014 36 x 96 0.0747 3.125 75.00 36 x 120 0.0747 3.125 93.75 48 x 96 0.0747 3.125 100.00 48 x 120 0.0747 3.125 125.00 48 x 144 0.0747 3.125 150.00 60 x 120 0.0747 3.125 156.25 72 x 120 0.0747 3.125 187.50 72 x 144 0.0747 3.125 225.0016 36 x 96 0.0598 2.500 60.00 36 x 120 0.0598 2.500 75.00 48 x 96 0.0598 2.500 80.00 48 x 120 0.0598 2.500 100.00 48 x 144 0.0598 2.500 120.00 60 x 120 0.0598 2.500 125.00 72 x 120 0.0598 2.500 150.00 72 x 144 0.0598 2.500 180.0018 36 x 96 0.0478 2.000 48.00 36 x 120 0.0478 2.000 60.00 48 x 96 0.0478 2.000 64.00 48 x 120 0.0478 2.000 80.00 48 x 144 0.0478 2.000 96.00 60 x 120 0.0478 2.000 100.0020 36 x 96 0.0359 1.500 36.00 36 x 120 0.0359 1.500 45.00 48 x 96 0.0359 1.500 48.00 48 x 120 0.0359 1.500 60.00 60 x 120 0.0359 1.500 75.0022 48 x 96 0.0299 1.250 40.00 48 x 120 0.0299 1.250 50.0024 48 x 96 0.0239 1.000 32.00 48 x 120 0.0239 1.000 40.00

COLD ROLLED SHEETSCommercial Quality

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)

Visit the Alro Web Sitealro.com

alro.com alro.com

6-6

7 48 x 96 0.1800 7.660 245.12 48 x 120 0.1800 7.660 306.40 8 48 x 96 0.1650 7.030 224.96 48 x 120 0.1650 7.030 281.2010 48 x 96 0.1382 5.781 184.99 48 x 120 0.1382 5.781 231.24 48 x 144 0.1382 5.781 277.49 60 x 96 0.1382 5.781 231.20 60 x 120 0.1382 5.781 289.05 60 x 144 0.1382 5.781 346.8011 48 x 96 0.1233 5.156 164.99 48 x 120 0.1233 5.156 206.24 48 x 144 0.1233 5.156 247.49 60 x 96 0.1233 5.156 247.68 60 x 120 0.1233 5.156 257.80 60 x 144 0.1233 5.156 309.6012 36 x 96 0.1084 4.531 108.74 36 x 120 0.1084 4.531 135.93 48 x 96 0.1084 4.531 144.99 48 x 120 0.1084 4.531 181.24 60 x 96 0.1084 4.531 181.20 60 x 120 0.1084 4.531 226.55 60 x 144 0.1084 4.531 271.8013 48 x 96 0.0897 3.906 124.99 48 x 120 0.0897 3.906 156.2414 36 x 96 0.0785 3.281 78.74 36 x 120 0.0785 3.281 98.43 48 x 96 0.0785 3.281 104.99 48 x 120 0.0785 3.281 131.24 48 x 144 0.0785 3.281 157.49 60 x 96 0.0785 3.281 131.20 60 x 120 0.0785 3.281 164.05 60 x 144 0.0785 3.281 196.8016 36 x 96 0.0635 2.656 63.74 36 x 120 0.0635 2.656 79.68 48 x 96 0.0635 2.656 84.99 48 x 120 0.0635 2.656 106.24 48 x 144 0.0635 2.656 127.49 60 x 96 0.0635 2.656 106.40 60 x 120 0.0635 2.656 132.80 60 x 144 0.0635 2.656 159.60

GALVANIZED SHEETSCommercial Quality (Lock Form Quality)A continuous mill annealing and galvanizing process produces sheets with a tight, even coat of spangle that will not flake or peel in forming operations. Normally stocked in a G-90 coating weight.

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)


6-7

18 36 x 96 0.0516 2.156 51.74 36 x 120 0.0516 2.156 64.68 48 x 96 0.0516 2.156 68.99 48 x 120 0.0516 2.156 86.24 48 x 144 0.0516 2.156 103.49 60 x 96 0.0516 2.156 86.40 60 x 120 0.0516 2.156 107.80 60 x 144 0.0516 2.156 129.6020 36 x 96 0.0396 1.656 39.74 36 x 120 0.0396 1.656 49.68 48 x 96 0.0396 1.656 52.99 48 x 120 0.0396 1.656 66.24 48 x 144 0.0396 1.656 79.49 60 x 96 0.0396 1.656 66.40 60 x 120 0.0396 1.656 82.80 60 x 144 0.0396 1.656 99.60 22 36 x 96 0.0336 1.406 33.74 36 x 120 0.0336 1.406 42.18 48 x 96 0.0336 1.406 44.99 48 x 120 0.0336 1.406 56.24 48 x 144 0.0336 1.406 67.49 60 x 96 0.0336 1.406 56.40 60 x 120 0.0336 1.406 70.30 60 x 144 0.0336 1.406 84.60 24 36 x 96 0.0276 1.156 27.74 36 x 120 0.0276 1.156 34.68 48 x 96 0.0276 1.156 36.99 48 x 120 0.0276 1.156 46.24 48 x 144 0.0276 1.156 55.49 60 x 96 0.0276 1.156 46.40 60 x 120 0.0276 1.156 57.8026 36 x 96 0.0217 0.906 21.74 36 x 120 0.0217 0.906 27.18 48 x 96 0.0217 0.906 28.99 48 x 120 0.0217 0.906 36.24 48 x 144 0.0217 0.906 43.49 60 x 120 0.0217 0.906 45.3028 36 x 96 0.0187 0.781 18.74 36 x 120 0.0187 0.781 23.43 48 x 96 0.0187 0.781 24.99 48 x 120 0.0187 0.781 31.2430 36 x 96 0.0157 0.657 15.77 36 x 120 0.0157 0.657 19.71

GALVANIZED SHEETSCommercial Quality (Lock Form Quality)

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)

6-8

10 48 x 96 0.1382 5.781 184.96 48 x 120 0.1382 5.781 231.20 60 x 120 0.1382 5.781 289.0011 48 x 96 0.1233 5.156 164.99 48 x 120 0.1233 5.156 206.24 48 x 144 0.1233 5.156 247.49 60 x 120 0.1233 5.156 257.80 12 48 x 96 1.0840 4.531 144.99 48 x 120 1.0840 4.531 181.24 60 x 120 1.0840 4.531 226.55 14 48 x 96 0.0785 3.281 104.99 48 x 120 0.0785 3.281 131.24 48 x 144 0.0785 3.281 157.49 60 x 120 0.0785 3.281 164.05 16 48 x 96 0.0635 2.656 84.99 48 x 120 0.0635 2.656 106.24 48 x 144 0.0635 2.656 127.49 60 x 120 0.0635 2.656 132.80 18 48 x 96 0.0516 2.156 68.99 48 x 120 0.0516 2.156 86.24 48 x 144 0.0516 2.156 103.49 60 x 120 0.0516 2.156 107.8020 48 x 96 0.0396 1.656 52.99 48 x 120 0.0396 1.656 66.24 48 x 144 0.0396 1.656 79.4922 48 x 96 0.0336 1.406 44.99 48 x 120 0.0336 1.406 56.24 48 x 144 0.0336 1.406 67.49 24 48 x 96 0.0276 1.156 36.99 48 x 120 0.0276 1.156 46.24 48 x 144 0.0276 1.156 55.49

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)

GALVANNEALED SHEETSCommercial QualityGalvannealed sheet is carbon steel coated with zinc on both sides by the continuous hot dip process. Immediately as the strip exits the coating bath, the zinc coating is subjected to an in-line heat treatment that converts the entire coating to a zinc iron alloy, giving the sheet a better surface for painting. Normally stocked in an A-60 coating weight.

Visit the Alro Web Sitealro.com

alro.com alro.com

6-9

11 48 x 96 0.1234 5.180 165.76 48 x 120 0.1234 5.180 207.2012 48 x 96 0.1084 4.533 145.25 48 x 120 0.1084 4.533 181.32 60 x 120 0.1084 4.533 226.65 14 48 x 96 0.0785 3.283 105.05 48 x 120 0.0785 3.283 131.32 60 x 120 0.0785 3.283 164.15 16 36 x 96 0.0635 2.656 63.74 36 x 120 0.0635 2.656 79.68 48 x 96 0.0635 2.656 84.99 48 x 120 0.0635 2.656 106.24 60 x 96 0.0635 2.656 106.24 60 x 120 0.0635 2.656 132.8018 36 x 96 0.0516 2.156 51.74 36 x 120 0.0516 2.156 64.68 48 x 96 0.0516 2.156 68.99 48 x 120 0.0516 2.156 86.24 60 x 96 0.0516 2.156 86.32 60 x 120 0.0516 2.156 107.80

20 36 x 96 0.0396 1.656 39.74 36 x 120 0.0396 1.656 49.68 48 x 96 0.0396 1.656 52.99 48 x 120 0.0396 1.656 66.24 60 x 120 0.0396 1.656 82.80

GageSize

(inches)


Est. Wt.Per Sq. Ft.

(lbs.)

Est. Wt.Per Sheet

(lbs.)

ALUMINIZED SHEETSCommercial QualityAluminized coated carbon steel sheets have an aluminum and silicon alloy coating on both sides. They are principally used in heat-resisting applications and also where corrosion and heat are involved.

SHEARED SHEET BLANKSInvestment conscious customers rely on Alro Steel to provide them with sheared sheet blanks. A battery of shears, working around the clock, assure availability of material to meet production schedules. This results in reduced inventory and handling costs, less in-plant scrap accumulations, and provides customers with quality blanks ready for immediate processing.

888-888-ALRO 2 5 7 6

Contact us today and learn more about

The Alro Difference!

6-10

4 .2242 9.376 4 . . . . . . . . . . . .

5 .2092 8.748 5 . . . . . . . . . . . .

6 .1943 8.125 6 . . . . . . . . . . . .

7 .1793 7.498 7 . . . . . . . . . . . .

8 .1644 6.875 8 . . . . . . . . . . . .

9 .1495 6.252 9 . . . . . . . . . . . .

10 .1345 5.624 10 .1382 5.779

11 .1196 5.001 11 .1233 5.156

12 .1046 4.374 12 .1084 4.533

13 .0897 3.751 13 .0934 3.906

14 .0747 3.124 14 .0785 3.283

15 .0673 2.814 15 .0710 2.969

16 .0598 2.501 16 .0635 2.655

17 .0538 2.250 17 .0575 2.405

18 .0478 1.999 18 .0516 2.158

19 .0418 1.748 19 .0456 1.907

20 .0359 1.501 20 .0396 1.656

21 .0329 1.376 21 .0366 1.531

22 .0299 1.250 22 .0336 1.405

23 .0269 1.125 23 .0306 1.280

24 .0239 .999 24 .0276 1.154

25 .0209 .874 25 .0247 1.033

26 .0179 .749 26 .0217 .907

27 .0164 .686 27 .0202 .845

28 .0149 .623 28 .0187 .782

29 .0135 .562 29 .0172 .719

30 .0120 .500 30 .0157 .657

HOT AND COLD ROLLED SHEET TOLERANCESMANUFACTURERS’ STANDARD GAGE

ToleranceRange

(inches) HR P&O CRGauge

DecimalEquiv.

(inches)

PoundsPer

SquareFoot

ToleranceRange

(inches)Gauge

DecimalEquiv.

(inches)

PoundsPer

SquareFoot

Hot Rolled, HR P&O, Cold Rolled Galvanized, Galvannealed

Guideline only. Some products are not produced in all gauge ranges.

.2332 .2152 .2182 .2002 .2033 .1853 .1873 .1713 .1724 .1564 .1575 .1415 .1425 .1405 .1472 .1265 .1285 .1292 .1276 .1256 .1323 .1116 .1136 .1143 .1126 .1106 .1174 .0966 .0986 .0994 .0967 .0947 .1014 .0827 .0847 .0854 .0817 .0797 .0865 .0677 .0697 .0705 .0733 .0723 .0770 .0613 .0623 .0650 .0658 .0648 .0695 .0538 .0548 .0575 .0598 .0578 .0625 .0478 .0498 .0525 .0528 .0518 .0566 .0428 .0438 .0466 .0458 .0506 .0378 .0406 .0389 .0436 .0329 .0356 .0359 .0406 .0299 .0326 .0329 .0376 .0269 .0296 .0299 .0346 .0239 .0266 .0269 .0316 .0209 .0236 .0239 .0287 .0179 .0207 .0199 .0247 .0159 .0187 .0184 .0232 .0144 .0172 .0169 .0217 .0129 .0157 .0155 .0202 .0115 .0142 .0140 .0187 .0100 .0127

6-11

Laser cutting is an excellent process for carbon steel, stainless steel and aluminum.

Other advantages include:

• High quality cuts • High precision cut parts

• Higher speeds than precision plasma under 1/8 inch

• Minimal clean up

• Narrow kerf width

• Smallest heat affected zone

Laser Cutting Technology

To request a burning quote for your existing CAD drawing please send it along in an email, to:

[email protected]

Shearing

Shearing sheet metal and plate steel is performed in most of Alro’s steel warehouses. We’ll shear your order to your exact specifications, place your material on a skid for safe transporting and safe handling after your order is delivered to your specified location.

We are capable of shearing plate up to 1/2” thick. Thickness capacities vary depending on the grade of the material. Please inquire.•

Sheared products are wrapped for protection and skidded for delivery.

Contact us today

888-888-ALRO 2 5 7 6

6-12

Contact us today

888-888-ALRO 2 5 7 6

888-888-ALRO (2576)

Home Online Store Metals Industrial Supplies Plastics Processing Catalogs e-Business News Locations Contact Careers

January 05, 2015

Alro Plastics: 5-Axis Waterjet CuttingAlro's plastics processing capabilities have reached a newlevel of sophistication with the addition of a new Flow 5-AxisWaterjet Cutter!

Waterjet - AlroPlastics

SmartCell™ Michigan Walter/Blaxx

Metals

Cold Finished BarsHot Rolled BarsAluminumStainlessHot Rolled PlateCarbon SheetStructuralTubing/PipeAlloysBrassCopper

BronzeRebarTool SteelDrill RodFlat Ground StockCast IronChrome Plated BarExpanded MetalGratingStrappingWire Mesh

Industrial Supplies

Grinding & SandingHole MakingBoringThreadingMillingTurning & GroovingReamingTool HoldingWork HoldingSawingShop Supplies

Fluids & LubricantsDie Sets & SuppliesPunchesFastenersMachineryHand/Power ToolsMaterial HandlingShelvingTool StoragePaper Products

Plastics

ABSAcetalsAcrylicCast NylonsDelrin®FiberglassLaminatesMakrolon®Medical GradesMicarta®

NylonPEEKPlexiglas®PolycarbonatePolyethylenePTFETIVAR®Tooling BoardUHMW-PEUrethane

Metals Processing

Saw CuttingFlame CuttingWaterjet CuttingShearingPlate Laser CuttingPlasma CuttingTube Laser CuttingPress Brake/FormingProduction Precision Saw CuttingGrindingThermal ProcessingPrecision Aluminum Plate Sawing

Industrial Supply Services

Gage CalibrationChain Sling Inspection/CertificationBand Saw Preventative MaintenanceBand Saw RepairBand Saw Blade WeldingCutting Tool ResharpeningTool Repair (indexable tools, toolholders, etc.)Cost Savings AnalysisCustomer In-Plant TrainingCoolant Lab Testing

Plastics Processing

Bending & GluingCAD/CAMCNC Routing & MachiningCNC Saw CuttingDrilling and TappingFiberglass Saw CuttingPlastics ProcessingRod and Tube CuttingPlastic WeldingWaterjet Cutting (5 Axis)

Search

Visit the Alro Web Site to learn more about

The Alro Difference!alro.com

Documents

CARBON SHEET - Alro Steel ASTM A1011 CS TYPE B HOT ROLLED SHEETS HOT ROLLED PICKLED & OILED SHEETS A prime quality low carbon sheet suitable for …