Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Canaline Marine Engines
Owners Handbook
Engines Models
Canaline 38
Canaline 42
Canaline 52
Canaline 60
Canaline 70T
Failure to read this or carry out the required service programme may invalidate your warranty
2
3
Index
Introduction 4 Engine Identification 5 Symbols in the Manual and on Engines 6
Safety precautions 7 Canaline Engine Technical Data 9
Starting & Stopping the engine 10 Fuel, Oil & Coolant Specifications 13 Maintenance Schedule 16 Installation Information Wiring diagrams & battery Cables 24 Anti-Vibration Mounts / Alignment installation 29 Exhaust Systems 30 Calorifier Connections / Position 31 PRM 125 Cable installation 33 Laying-up Considerations 33 Fast Moving Parts list 34 UK Dealer Network 35 Declaration of Conformity Certificate 36 Emission Durability Statement 37 Warranty Terms and conditions 38 Service Record 41 Warranty registration card Loose
4
Introduction
This Canaline Marine diesel engine is based on the Kioti diesel engine which is
manufactured by Daedong Industrial Co Ltd.
Engines Plus Ltd wishes to thank you for purchasing your new Canaline Marine Diesel
engine. Your new engine is the result of many years of research and development,
and high quality manufacturing. This engine is designed based on strict quality
standards applied to and use of Kioti genuine components. Its knowledge on the
operation of the diesel engine is based on faithful service and reliability for years.
This manual makes users familiar with the diesel engine and provides useful
information on safety, operation, and maintenance of the diesel engine.
To get the fullest use and benefit from your marine engine, it is important that you
install, operate and maintain it correctly. This manual, along with gearbox operators’
handbook, is designed to help you do this.
Please read this manual carefully and follow its operating maintenance
recommendations, along with the installation guidelines. This will ensure many years of trouble-free and economical engine operation.
Should you require further advice, technical assistance or an engine service, please
contact your nearest marine engine outlet, he knows your engine best and is ready to meet your requirements.
On completion of the warranty registration card, please return it to Engines Plus Ltd,
where we can log it.
All information, illustrations, and specifications contained in this Manual are based on
the latest product information available at the time of publication.
Engines Plus Ltd is a mariniser of industrial diesel engines, of which the Canaline
product is part of our product portfolio. Engines Plus Ltd produces this manual for use
on the Canaline marine engine based on the Kioti Diesel engine.
Engines Plus Ltd reserves the right to make changes in this manual at any time
without prior notice.
The information given is subject to the company’s current conditions of Tender and
Sale, is for the assistance of users, and is based upon results obtained from tests
carried out at the place of manufacture and in vessels used for development
purposes. We do not guarantee the same results will be obtained elsewhere under different conditions.
5
Engine Identification
NOTE: In all communications with the Engines Plus Ltd or a local dealer the engine
serial number and engine type must be quoted.
The engine serial number is on a decal affixed to the top surface of the Rocker Cover,
as shown below. The Kioti Engine Number is also stamped on the Engine Block,
outboard of the Injection Pump Flange.
As part of your engine warranty please return your registration card, which is
supplied loose, as soon as possible.
Engine Information Fill in your engine information below, so you have it to hand when contacting your
local dealer.
Engine Type:
EP Serial No:
Gearbox Type:
Gearbox Number:
Date of Installation:
Engines Plus Ltd
Engine Serial Number Decal
Kioti Engine Serial Number Stamping
6
Prescription-Indication notices (rectangle);
it is obligatory to adopt the protective
measures shown in the notices to perform the operation in question in total safety.
Danger Warning-Attention Notices
(triangular); General Attention
regarding personal safety and protection of the engine
Prohibition Notices (Circular)
indicating potentially hazardous situations.
Identification Notices (No Border)
Symbols in the Manual and on Engines
General operational note
Protect hands (Gloves)
Protect eyes (Safety Glasses)
Protect respiratory passages (Mask)
Danger! General Danger situation
Danger! Electrical Discharges
Danger! Sources of Heat
Danger! Engine Coolant Pressure
The operation indicated in the text is strictly prohibited
Danger! From moving Parts ~ do not perform maintenance work.
Engine Coolant Level
Engine Oil Level
Engine Lubricating Oil ~ Fill Point
Lifting Point ~ Engine & Gearbox ONLY
Engine Coolant ~ Fill Point
Read the Manual.
7
Safety Precautions
Keep the engine, gearbox and surrounding area clean, including the area
immediately below the engine.
Drives – Power Take Off Areas
Gearbox Output Flange
The purpose of the marine diesel propulsion engine is to provide motive power to
propel a vessel. Accordingly the gearbox output shaft rotates and its flange is
designed to be coupled to a propeller shaft by the installer. Steps must be taken
to ensure adequate guarding.
Forward End Drive
Engines are supplied with unguarded vee and poly vee belt drives to power the
fresh water pump and battery-charging alternator. The installer must ensure that
it is not possible for injury to occur by allowing accessibility to this area of the
engine. The drives can cause injury if personnel or clothing come in contact with
the moving belts or pulleys, when the engine is running.
Exhaust Do not touch Hot Surfaces
Exhaust Outlet Diesel marine propulsion engines emit exhaust gases at high temperatures –
around 400 - 500°C. Engines are supplied with either wet exhaust outlet (water injection bend) or dry outlet (dry exhaust stub) – see engine price list. At the
outlet next to the heat exchange header tank, the exhaust outlet can become very hot and if touched, can injure. This must be lagged or avoided by ensuring
adequate guarding. It is the responsibility of the installer to lag the exhaust system if a dry system is used. Exhaust gases are harmful if ingested, the
installer must therefore ensure that exhaust lines are routed overboard and that
leakage into the vessel does not occur.
Fuel Do not ingest liquids
Fuel Lines
Diesel engines are equipped with high pressure fuel injection pumps, if leakage
should occur, or pipes fracture, fuel at high pressure can be harmful. Skin must
be thoroughly cleaned in the event of contact with diesel fuel.
Fuel Supply Connections
Engines are supplied with 8mm fittings. The installer must ensure that when
connections are made, they are clean and free of leaks.
8
Oil Do not ingest liquids
The Canaline marine propulsion package is supplied with 2 dipsticks, one for the
engine and one for the gearbox. Ensure dipsticks are returned and secure after
checking. If not, oil leaks can cause infection when touched. Do not remove
dipsticks whilst engine is running, as this can cause oil to blow out. All oil must be
removed from the skin to prevent infection.
Scalding Do not remove Pressure Cap when Hot
An engine running under load will have a closed circuit fresh water temperature of
71° to 85°C. The pressure cap on the top of the header tank must not be
removed when the engine is running. It should only be removed when the engine
is stopped and has cooled down.
Transportation/Lifting
Engines are supplied on transportable pallets. Lifting eyes on engines are used for lifting engine and gearbox assembly only, not the pallet and associated kit.
GENERAL DECLARATION
This machinery is not intended to be put into service until it has been incorporated into or with other machinery. It is the responsibility of the purchaser/installer/owner,
to ensure that the machinery is properly guarded and that all necessary health and
safety requirements, in accordance with the laws of the relevant country, are met before it is put into service.
Note: Recreational Craft
Where applicable, the purchaser/installer/owner and operator must be responsible for
making sure that Directive 2013/53/EU is complied with.
9
Canal Boat Engines – Technical Data
Model Canaline
38
Canaline
42
Canaline
52
Canaline
60
Canaline
70T
Cylinders 4 4 4 4 4
Bore mm 83.0 83.0 87.0 87.0 87.0
Stroke mm 92.4 92.4 92.4 102.4 102.4
Displacement cc 1999 1999 2179 2430 2430
Combustion Indirect Injection
Cooling Keel Cooled
Power
Output Bhp 38 42 52 57 65
ISO 8665
Rated Power @ Speed
kW 29.2 32.6 32.6 35.2 41.9
r/min 2600 2600 2600 2600 2600
Max Torque Nm 125 131 145 158 192
r/min 1600 1600 1600 1600 1800
Oil Capacity litres 8.0 8.0 8.0 9.7 9.7
Weight kg 235 237 248 256 256
Engine
Coolant
Capacity
Litres 7.5 7.5 7.5 8.3 7.3
Alternator Amps 75 & 100 75 & 175 75 & 175 75 & 175 75 & 175
Starter Motor kW 1.7
Air Intake
restriction kPa 2.45 max
Exhaust Back
Pressure kPA 10.0 max
Ventilation
required M3/min 2.25 2.25 2.65 3.07 3.15
Gearbox PRM 125 PRM 150 PRM 150 PRM 150 PRM 150
Starter
Battery size Minimum recommended size - 700 CCA / 100 Ah
Note: The specification details above are for standard configurations.
BHP* ~ to EN ISO8665
10
Starting and Stopping
Important checks prior to use
Your engine has been filled with new oil for both engine and gearbox when it leaves
the factory. However, please check, see the section on engine maintenance.
Ensure the engine is free to turn without obstructions, and daily checks have been
carried out.
Ensure battery is fully charged and connected (the isolator is in the ‘ON’ position).
Ensure Morse speed and gearbox cables are fitted correctly and that cable travel
lengths are correct.
Ensure fuel taps from fuel tank have been turned on
CAUTION: for safety’s sake conduct checks above, with engine stopped, before starting.
Engine starting Check the engine and gearbox oil levels are correct ~ see relevant section in this
manual for further information. • Set the engine throttle to 1/3, out of gear.
• Turn the Key to the “1” Position. The panel will go through a procedure to ensure all lights and the buzzer are working,
once this has been completed you can then start the engine.
• Turn the Key to Pre-Heat, and hold until the Yellow light goes out.
• Turn the Key to the Start/Crank position and release when the engine fires.
Ensure alarm buzzer is not sounding and red warning lights are off.
Note:
If the alternator warning light is still on then increase the engine speed to excite the alternator, then return to idle. The light should then go out.
Make sure the engine is running smoothly, with no smoke and sounds normal.
Repeated engagement of the starter to the flywheel ring gear without a break will
result in damage to the starter pinion gear and flywheel ring gear. It will also cause
excessive build-up of heat in the Starter Motor Windings.
It may also cause the Engine Stop Solenoid to burn out due to heat build-up.
Crank for no longer than 20 seconds, with at least a 20 second break between
attempts.
The oil pressure gauge on the deluxe engine control panel may read high on start-up
and whilst the engine is cold. This is normal, and it will then decrease to the running
level.
11
STOPPING Every propulsion engine is fitted with a stop solenoid. To stop engine simply turn the
key to the “0” position and the engine will stop.
When leaving the boat for an extended period, turn off battery isolator.
Canaline Engine Control Panels
Canaline Engine control panels feature LED Module to indicate as listed below. An
Intermediate Panel is shown for illustration only.
1 4
2 5
3 6
1. Yellow ~ Timed Preheat LED Illuminates when Key is switched to preheat position to indicate Preheat time.
2. Red & Buzzer ~ Engine Coolant Temperature LED Illuminates and Buzzer sounds if Engine Temperature is too high.
3. Red & Buzzer ~ Starter Alternator LED Illuminates and Buzzer sounds if no charge from Alternator or Belt breaks.
4. Green ~ Panel Power LED illuminates when Key is switched on.
5. Red & Buzzer ~ Engine Oil Pressure LED Illuminates and Buzzer sounds if Oil Pressure is too low.
6. Red & Buzzer ~ Auxiliary / Domestic Alternator LED Illuminates and Buzzer sounds if there is no charge from Alternator or Belt breaks.
12
Checks during operation
While operating the engine, keep checking whether all parts of the engine are
operating smoothly and correctly.
COOLING SYSTEM Do not remove Pressure Cap when Hot
If steam or coolant is escaping from the overflow tube; stop the engine, allow it to
cool, and check the following and correct as needed.
1. Check for cooling system leaks.
2. Check for obstructions that block cooling air.
3. Check and adjust the fan belt tension.
4. Ensure that the system is filled to the correct coolant level with the proper mix of
Coolant Concentrate (anti-freeze) and water.
5. Check the radiator cap for proper type and condition.
IMPORTANT
To avoid personal injury:
DO NOT remove the Manicooler cap while the engine is hot. Pressurized steam or coolant will escape and cause serious injury to
you and any bystanders. Open the cap at least 10 minutes after the engine is stopped.
OIL PRESSURE LED The oil pressure LED comes on when the oil pressure drops below a safe level. If the
lamp comes on while the engine is operated at or above 850 rpm, immediately stop the engine and check the engine oil level.
FUEL
The fuel tank should never be allowed to become completely empty. An empty tank will allow air into the fuel system; and the engine will not operate without bleeding
the fuel system.
EXHAUST SMOKE
The engine exhaust should be colorless during normal operation within the rated
output of the engine. Continuous dark emissions or smoke may indicate improper
usage or an engine malfunction.
STOP THE ENGINE IMMEDIATELY:
1. If the engine speed suddenly changes.
2. If there is an unusual noise.
3. If the engine exhausts suddenly darkens.
4. If the oil pressure, temperature light or alternator comes on.
13
Fuel and Oil Specifications
Fuel
Important
• It is advisable to fit a fuel/water separator in the fuel supply system. Water in the
fuel can damage the injection system. However if the engine is being fitted into an
existing boat (re-installation), it is compulsory to fit a fuel/water separator
• If a fuel supply shutoff valve is fitted do not use a taper tap, only use a ball valve
tap. The ball valve type are more reliable and less likely to let air into the fuel
system.
• Do not use Kerosene, which is very low in cetane rating and lubricity, and may
adversely affect the engine.
• Be careful not to let the fuel tank become empty, or air can enter the fuel system,
necessitating bleeding before next engine start.
Fuel selection
The following criteria is required for the diesel fuel…
1. Must be free from minute dust particles. 2. Must have adequate viscosity.
3. Must have high cetane value. 4. Must have high fluidity at low temperature.
5. Must have low sulphur content.
6. Must have little residual carbon.
Diesel fuels
Applicable standard Recommendation
JIS (Japanese Industrial Standard)
DIN (Deutsches Institut für Normung) SAE (Society of Automotive Engineers)
Based on SAE-J-313C
BS (British Standard)
NO. 2
DIN 51601
NO.2-D
BS EN590:2009
If fuel other than specified is used, engine functions will be lowered.
Fuel Requirements
NOTICE: The fuel injection pump, injector or other parts of the fuel system and
engine can be damaged if you use any fuel or fuel additive other than those
specifically recommended by Canaline / Kioti.
Such damage is not the responsibility of Canaline / Kioti and is not covered by their
Warranty.
To help avoid fuel system or engine damage, please read the following:
14
• Some service stations mix used engine oil with diesel fuel. Some manufacturers
of large diesel engines allow this; however for your diesel engine, do not use
diesel fuel, which has been contaminated with engine oil.
• Do not use any fuel additive (other than as recommended under “Biocide” in this
section). At the time this manual was printed, no other fuel additive was
recommended. (See your authorisation dealer to find out if this has changed).
Fuel system air bleeding
The entry of air into the fuel system will cause difficult engine starting or engine
malfunction. When servicing such as emptying the fuel tank, draining the Water
Sedimenter, and the fuel filter element change, be sure to bleed air.
Air Bleeding Procedure:
1. Please refer to the Changing the Fuel Filter section.
2. Start the engine and thoroughly check the fuel system for leaks.
CAUTION: the water/diesel fuel mixture is flammable and could be hot. To help
avoid personal injury and/or property damage to not touch the fuel coming from the drain valve and do not expose the fuel to open flames or sparks. Be sure you do not
overfill the container. Heat (such as from the engine) can cause the fuel to expand. If the container is too full, fuel could be forced out of the container. This could lead
to a fire and the risk of personal injury and/or vehicle or equipment damage.
Biocides In warm or humid weather, fungus and/or bacteria may form in diesel fuel if there is
water in the fuel.
NOTICE: fungus or bacteria can cause fuel systems damage by plugging the fuel
lines, fuel filters or injector. They can also cause fuel system corrosion.
If fungus or bacteria has caused problems, you should have your authorised dealer
correct these problems. Then, use a diesel fuel biocide to sterilise the fuel system
(follow the biocide manufacturer’s instructions). Biocides are available from your dealer, service stations, parts stores and other automotive places. See your
authorised dealer for advice on using biocides in your area and for recommendations
on which biocides you should use.
Smoke suppressants
Because of extensive testing of treated fuel versus untreated fuel, the use of a smoke
suppressant additive is not recommended. This may enhance the possibility of stuck
rings and valve failure, resulting from extensive ash deposits.
Fuels used should contain no more than 7% Biodiesel. Exceeding this
amount will invalidate Warranty and may affect compliance with Emission
Approval.
15
Lubricant
The quality of engine oil may affect engine performance, start-ability and engine life.
The use of unsuitable oil may result in piston ring stick, piston and cylinder seizure,
and accelerate sliding surface wear causing increased oil consumption, lowered
output and possible engine failure.
To avoid this, use the specified engine oil.
Engine Oil Selection
Engines Plus Ltd recommends oil to the following specifications…
API CC or CD specification is used in Canaline 38, 42, 52 & 60 Marine engines.
API CH is used in Canaline 70T Marine engines.
Either 10W/40 or 10W/30 is acceptable for temperate climates.
Do NOT use Synthetic or Semi-Synthetic Oils in Canaline Marine engines.
The correct grade oil is available from your local marine dealer.
• 5 litres API CC 10W/40 – EPL Part No - EP710008 - CL38~60 • 25 litres API CC 10W/40 – EPL Part No - EP710009 – CL38~60
• 5 litres API CH-4 15W/40 – EPL Part No - EP710560 – CL70T ONLY
• 25 litres API CH-4 15W/40 – EPL Part No - EP710561 – CL70T ONLY
Coolant
Two main types of Coolant Concentrate (Anti-freeze) are available, and either may be used…
1. Blue ~ standard Coolant Concentrate, which has a typical service life of
12months.
2. Red/Orange ~ Long Life Coolant Concentrate which has a typical service life of 2~3 years.
Both types should be mixed with clean water, up to a maximum concentration of
50%. Refer to the product container or specification sheet for frost protection vs
concentration, and recommended service life.
16
Maintenance
Schedule
Daily or every 8 hours running.
• Check engine oil level.
• Check gearbox oil level, see gearbox manual.
• Check coolant level.
• Check drive belt tension, adjust if necessary.
• Check colour of exhaust fumes and unusual engine noise on start up.
• Check stern gland lubrication.
After first 50 hours.
• Change gearbox lubricant (see separate gearbox manual).
• Change engine lubricating oil.
• Change oil filter.
• Change fuel filter. • Check fuel contamination and drain off water trap/Agglomerator if fitted.
• Check Air Filter Element for contamination, and change if necessary. • Check all water pipes are not chaffing and for any leaks, and adjust if necessary.
• Check all fuel pipes are not chaffing and for any leaks, and adjust if necessary. • Check exhaust system for any leaks, etc, and adjust if necessary.
• Check wiring looms and cables are not chaffing, and adjust if necessary. • Check coupling alignment and ensure all bolts are tight.
• Check bolts/nuts on the anti-vibration mounts are tight and secure. • Check control cables installation to ensure gearbox is correctly being engaged, and
adjust if necessary.
Every 200 hours or every year.
• As 50 hours and the following -
• Check air cleaner element and replace if necessary.
• Change oil and oil filter.
Every 400 hours. • As 50 & 200 hours and the following -
• Change air cleaner element.
• Change fuel filter.
• Change anti-freeze.
• Check electrical equipment, condition of hoses and belts, replace as necessary.
First Service
A new marine engine will require an engine service and check over at 50 hours. The
LCD display in the tachometer shows the engine running hours.
It is very important that this is carried out, as this includes many checks to ensure
the engine has settled down correctly.
This is chargeable and is the owner’s responsibility to organise, failure to do so may invalidate warranty.
17
Checking engine oil level Do not ingest liquids
For quantities of oil please refer to page 7. When checking the engine oil level, do so
before starting or more than five minutes after stopping.
1. To check the oil level, draw out the dipstick, wipe clean, re-insert it and draw it
out again. Check to see that the oil level lies between the two major marks on
the dipstick. (please ignore the middle smaller mark)
2. If the level is too low add new oil via the oil filler port, to the specified level –
do not overfill.
Important When using oil of different make or viscosity from the previous one, drain old oil.
Never mix two different types of oil. Engine oil and filter should be changed after the
first 50 hours running time and then every 200 hours or every year. Oil filter is a
cartridge type mounted on the side of the engine.
Engine Dipstick
Engine Oil goes in here
18
Sump drain
Pump - tap
Changing Engine Oil Do not ingest liquids
1. Run the engine for 10 minutes to warm up the oil.
2. Your engine is provided with a sump drain pump. Turn the tap to “on”. Use
the hand pump as shown to pump out the oil into a bucket. Turn the tap to off
position and replace end cap.
3. Unscrew the oil filter and replace with a new one. See diagram below
Note: it is best to wrap a plastic bag around the filter, to catch any oil left in the
system. (Always keep your bilges clean!) Before screwing in the new filter spread a thin film of oil round the rubber gasket to ensure a good seal and screw in – hand
tight.
4. Fill the engine with new oil, refer to page 13 for specification, as described above.
Note: once you have re-filled the engine will oil, run the engine for about 5 minutes,
so the oil can be pumped around the engine and into the new filter. Stop the engine,
and let it settle for about 10 minutes, and re-check the oil level, fill if required.
Sump drain Pump Oil Filter
19
Changing the fuel filter
1. The fuel filter is a spin-on Cartridge.
Remove by turning anti-clockwise when viewed from
below, see picture….
2. Replace the fuel filter cartridge every 400 hours
3. Remove metal bung and O Ring from the
old fuel filter and fit to new fuel filter (see below)
4. Apply fuel oil thinly over the filter gasket and tighten
into position – hand tight
5. Prime fuel system…
Place a rag or receptacle under the Fuel Filter
Slacken the Bleed Screw
Pump the Fuel Primer until air free fuel comes from
the Bleed Screw, then tighten the Bleed Screw
Continue to pump until a reasonable effort is
required.
6. Check for leaks
Note: Do not get fuel on the flexible engine mounts
.
Fuel Filter
Metal bung in Fuel filter, must
be transferred to new fuel filter
Fuel Primer Bleed Screw
20
Checking Gearbox Oil Level – please refer to gearbox manual, but on the PRM
120 & 125D mechanical gearboxes, please ensure the following
Never exceed the maximum oil level on the dipstick!
Always use ATF Dextron II or III for your gearbox
PRM125D
The PRM125D Gearbox is fitted with a Level Plug, as shown below. This should be
used when re-filling the gearbox with oil after draining, to allow an easy and quick
reference.
NOTE: When checking the oil level, ensure the Gearbox is in neutral, start and run
the engine for a short time to circulate oil. Stop the engine and allow the oil to settle
for 2 minutes. Check the oil level with the Dipstick. NOTE: The Dipstick should be secured firmly when checking the oil level.
Ensure the oil mark is below the marker
on the dipstick (shaded). Ensure thread (shaded) is fully screwed down
into case with its relevant bonded seal when
measuring the oil level.
21
Freshwater Cooling System
New engines are supplied with the freshwater drained off.
The following instructions must be followed to fill the system.
(a) Mix up in a clean bucket a solution of 50% anti-freeze/water mix.
(b) Fill engine with the freshwater/anti-freeze solution through the top of the
header tank with the filler/pressure cap removed.
(c) Fill the header tank to the top of the filler neck and replace cap. Press down
firmly on filler cap and hand tighten in a clockwise direction.
Note: for keeled cooled engines a larger volume of freshwater/anti-freeze mix is
required depending on the size of the keel cooling tank – refer to the builder.
(d) Run the engine for 5 minutes on no load (out of gear) and then check the
coolant level. Top up if necessary.
(e) Check the complete system for leaks, including the Calorifier circuit if fitted.
Note: for keel cooled engines it is very important to bleed all the air out of the
system before the engine is run on load (check the boat builders’ instructions).
(f) If a Calorifier is fitted care must be taken to see that this is also full of coolant and all air is expelled. (see Calorifier notes in installation section)
(g) Run the engine on one third speed for 15 minutes, preferably with the boat tied up. As the system warms up coolant may be expelled from the overflow pipe
into the bilge. Stop the engine and allow the engine to cool down before removing the pressure cap and top up the coolant to 25mm below the filler
neck.
Important
Removal of the pressure cap from a hot engine, can cause severe injury from hot coolant under pressure. Always allow the engine to cool and then use a large cloth
when turning the cap anti-clockwise to the stop. This allows the pressure to be
released. Press firmly down on the cap and continue to turn anticlockwise to release
the cap.
(h) Repeat (g) if coolant level is more than 25mm below the base of the filler neck
when the engine has cooled down.
(i) Run engine on 2/3 speed for 20 minutes, check for leaks and repeat (g)
(j) Anti-freeze solutions should be drained off every 400 hours or 2 years
whichever is sooner, and replaced with a new solution, dependant on the type
of Antifreeze used.
Engine water filler cap, integrated into
the header tank.
22
Changing the Air filter
The Air filter should be changed every 400 hours, once per year or sooner if
necessary.
The air cleaner fitted to the Canaline 38~60 marine engines, has a replaceable
element, part no EP110529.
1. Remove Air cleaner lid, by unscrewing anti-clockwise.
2. Remove the old element.
3. Wipe the inside of the Air Cleaner Body clean.
4. Replace a new element.
5. Re-locate lid, and turn clockwise until it clicks.
The air cleaner fitted to the Canaline 70T marine engine, has a replaceable element, part no EP110550.
1. Remove Air cleaner lid, by unclipping the 2 retaining clips.
2. Remove the old element. 3. Wipe the inside of the Air Cleaner Body clean.
4. Replace a new element.
5. Re-locate lid, and secure with the 2 clips, ensuring the dust valve is facing
downwards.
Air Cleaner
Element
Air Cleaner
Element
Retaining Clips
on the End Cap
23
Alternator Drive Belts
It is important to check both alternator drive belts to ensure both engine
performance and that batteries are charged
The 75 Amp alternator drive belt also drives the engine water pump.
To tighten both belts, please follow these instructions
1. Loosen nuts A
2. Use bolt B to tighten belt 3. Adjust accordingly
4. Retighten nut A after finish
Note: Low belt tension can result in engine overheating and insufficient battery
charging. A belt that is too tight may cause bearing failure and belt life may be shortened
Note: 75 Amp Alternator fitted to the Canaline 38 engines are not fitted with a
jacking bolt style tensioner link.
75 Amp
Alternator
Auxiliary
Alternator
Nut B Nut A
24
Engine Wiring Diagram Index
Engine Type Drawing Number
Canaline 38 / 42 / 52 / 60 / 70T
Engine Wiring Loom WD910524.2
Intermediate Engine Control Panel WD910506.1
Deluxe Engine Control Panel WD910507.1
Hirefleet Engine Control Panel WD910559.2
Starter Battery…..
For all Canaline Engines in this manual we would recommend a minimum Starter
Battery capacity of 700CCA / 100Ah
Starter Battery Cable Sizes…
The Starter Battery, should be positioned as close to the engine as is feasible, and safe.
For all Canaline engines, where the TOTAL cable run, ie from Battery to the engine
and back does not exceed …
2.5m, use 25mm2 cable. 3.5m, use 35mm2 cable.
7.5m, use 70mm2 cable.
Battery Cables which are too small will create excessive voltage drop and may
overheat and catch fire.
25
26
27
28
29
Marine Engine Installation Information
Anti-vibration Mount Installation
These mounts are supplied for use where accurate alignment is required, e.g.
between the gearbox output shaft and propeller shaft on marine installations. They
also provide isolation of the power unit, to minimise the transmission of vibration into
the hull.
Assembly and adjustment is as below:
Top Nut ‘C’Nyloc Nut ‘A’Lock Nut ‘ B’
X=7mm
Top Nut ‘C’Nyloc Nut ‘A’Lock Nut ‘ B’
X=7mmSet the gap ‘X’ between the lower face of the Nyloc Nut ‘A’ and the upper face of
Locknut ‘B’ to 7mm.
1. Attach each mount to the engine bearers and secure by tightening Top Nut ‘C’
2. Lower the propulsion unit, complete with mounts onto the beds or support
structure, ensuring that the base of each mounts is fully seated. If any clearance between the underside of the mounts and beds is found, proceed as
below:
3. (i) If the gap is less than 2mm, re-adjust Nyloc Nut ‘A’, until the base of the
mount contacts the bed face.
(ii) If the gap exceeds 2mm, a separate packing piece / shim should be
fitted.
4. Fit and tighten the bolts fixing the mounts to the bed. Tighten Top Nut ‘C’.
Alignment between the Gearbox and Propeller Shaft Flanges should now be checked, preferably using a dial indicator for concentricity and feeler gauges for
angular misalignment (see sketch).
Adjust the alignment by raising or lowering the Nyloc Nut ‘A’, to achieve
alignment within the limits of the Gearbox to Propeller Shaft Coupling, as
specified by the manufacturer. If a rigid coupling is used, then it is suggested
that eccentricity should not exceed 0.25mm (0.010”) total indicator reading
and, angular misalignment should be within 0.025mm (0.001”) per 25mm of
flange diameter.
30
Coupling alignment procedures should be re-checked after 10/15 hours of
operation, during which time any “settling” of the system should have taken place. If this is not possible, the power unit should be raised approximately
1mm on each mount after completing the alignment procedure.
5. If the distance between the underside of Nyloc Nut ‘A’ and the top of Locknut
‘B’ exceeds 15mm, then a 5mm Packing Piece should be inserted between the base of the mount and top face of the beds. Nyloc Nut ‘A’ should then be
adjusted to compensate.
6. Following any height adjustment on the mountings, alignment of the Coupling Flanges should be re-checked after tightening the Top Nut ‘C’ and Mount to Bed
Bolts securely.
NOTE……Locknut ‘B’ should NOT be loosened or adjusted at any time.
Exhaust System
Exhaust Back Pressure must remain within the limits specified in the Technical
Data section, to maintain Emission Compliance. This figure should be checked
at the Manicooler or Turbocharger Outlet Flange.
We recommend the use of the following Exhaust Silencer & piping size:…
Canaline 38, 42, 52 & 60… 1.5”BSP
Canaline 70T… 2”BSP
Where Exhaust Systems incorporate turns, it is preferable to use bends rather
than elbows, to minimise back pressure. A flexible bellows section should be
fitted immediately after the engine exhaust outlet.
31
Calorifier Connection Points – CL 38/42/52/60/70T
Calorifier connection points are as shown below. Connection stubs are provided and
are suitable to accept 15mm (5/8”) dia bore flexible hose. The hose must be secured
with suitable hose clips to give a watertight connection capable of withstanding a
water pressure of 15 psi. Hoses are not supplied by Engines Plus.
If no Calorifier is fitted, the connections must be blanked off, They MUST NOT BE
CONNECTED DIRECTLY TOGETHER, Blanking plugs are available on request.
HOT WATER OUTLET
To Calorifier
WATER RETURN
From Calorifier
Canaline 70T HOT WATER OUTLET
To Calorifier
32
Calorifier Position The Canaline Marine range has been developed to operate with approximately 3m of
piping between the engine and Calorifier, with a minimum number of bends and
restrictions in this pipework. We recommend the Calorifier Inlet and Outlet
connections be no more than 400mm above the top of the engine nor below the
bottom of the engine sump.
Provided these criteria are applied and the system is fully bled of air, then
satisfactory performance should result.
Both Feed and Return connections are situated on the engine side of the Thermostat,
and water is therefore allowed to circulate around the Calorifier Circuit at all times. It
should be noted that during long periods of engine operation, when no hot water is
drawn from the Calorifier, that the hot water temperature within could approach 80
degC. Under these circumstances, extreme care should be taken when using the hot
water circuit.
Engine Idle Speed The Canaline Marine engines idle speed should be set between 850 – 900 r/min,
however this can be adjusted by the installer if the engine idle speed is incorrect
without affecting the engines warranty.
To change idle speed, please adjust accordingly
Loosen nut A, and adjust idle speed with bolt B, then re-tighten nut A to lock the idle
speed, please ensure the cable is then re-adjusted accordingly
NOTE… where a Hydraulic Gearbox is fitted, the idle speed should be 850 r/min
minimum, to maintain sufficient hydraulic oil pressure in the Gearbox.
Nut A
Bolt B
33
PRM 125 Morse control cable installation It is highly important the Morse control cable and lever installation is performed
correctly, otherwise this may well lead to the early failure of your gearbox, which
would not be covered by warranty.
Ensure the cable that operates the selector lever allows the lever to travel fully to the
stops in the forward and reverse positions at all times, we would recommend that
you use the inside hole on the lever to ensure the lever fully engages and keep the
gearbox firmly in gear.
Laying-up procedure for Canal Boat Marine Engines
Where an engine is to be standing idle for periods of over 6 months consideration
should be taken to minimise the deterioration of components.
The engine should be stored in a clean, dry environment, which is free from frost and
damp. It is best stored in its delivered state from Engines Plus Ltd.
If the engine is to be installed and not used, it is best that the engine is not run prior
to its lay-up. The vessel containing the engine should be stored in a dry, frost free environment.
When storage for above 6 months is necessary, then the engine should be inhibited.
Failure to do so could promote corrosion internally. Contact Engines Plus Ltd for more
details.
The lever has a section of over
throw that the lever should sit in when the gear is selected.
The adjustment should be
regularly checked as cables
can stretch.
34
Parts Bulletin for Canal Boat Marine Engines
Engine Type : Canaline 38 Canaline 42 Canaline 52 Canaline 60
Canaline
70T
Kioti Engine
designation 4A200LWS 4A200LWS 4A220LWS 4B243LWS 4B243TLWS
Oil Filter Element E6201-32443
Fuel Filter Element E4682-43172
Air Filter Element EP110529 EP110550
Thermostat E5800-73011
Fan Belt - A section E6300-72532 E5800-72531
Starter Motor E5500-63016
75 Amp Alternator E7251-64011
100 Amp Auxiliary
Alternator EP910655 N/A
110 Amp Auxiliary
Alternator N/A EP910586
175 Amp Auxiliary
Alternator N/A EP910346
Glow Plugs E6301-65512
Oil Pressure Switch E5500-39013
Oil Pressure Switch
/ Sender EP910039
Engine Temperature
Switch EP910512
Engine Temperature
Sender EP910041
Top Hose EP410511 EP410693
Aux Alt Drive Belt
(80 / 100 A) - A Sec EP810975 N/A
Aux Alt Drive Belt
(110/175 Amp) N/A EP811065
Engine Oil - 5 Litre EP710008 EP710560
Engine Oil - 25 Litre EP710009 EP710561
Genuine Parts In order to protect your engine warranty, only Genuine Canaline parts must be used. These parts are available from our Dealer Network, or direct from Engines Plus Ltd.
35
Engines Parts – Availability
All engines parts are available through your local dealer or direct from Engines Plus
Ltd.
Our latest dealer network is available on our website –
www.canaline-engines.co.uk .
Listed below are our main parts centres
Servicing of the engine We would always recommend that the engine is serviced by a qualified engineer. We
have Dealers and Mobile Service Engineers, see website -
www.canaline-engines.co.uk for the latest information.
Uxbridge Boat Centre Ltd,
Uxbridge Wharf, Waterloo Road,
Uxbridge, Middx, UB8 2QX,
Tel: 01895 252019
Kings Lock Chandlery
Booth Lane, Middlewich, Cheshire.
CW10 OJJ.
Tel: 01606 737564
Wharf House Narrowboats
Braunston Boat Haven, Bottom Lock,
Little Braunston,
Northants. NN11 7HL
Tel: 01788 899041
36
EU Declaration of Conformity for Recreational Craft Propulsion Engines
Exhaust Emission Certification to the requirements of Directive 2013/53/EU.
Name of Engine Manufacturer: Daedong Industrial Co Ltd.
Name of Authorised Representative: Engines Plus Ltd
Address of above: Unit F, The Aquarius Centre, Edison Road,
Waterwells Business Park, Quedgeley GL2 2FN. UK
Name of the Notified Body for Exhaust Emission assessment: RDW
Address of above: PO Box 777, Zoetermeer, 2700AT, Nederland’s
This declaration of conformity is issued under the sole responsibility of the manufacturer, the private
importer or the person referred to in Article 19(3) or (4) of Directive 2013/53/EU.
The object of the declaration described in point 4 is in conformity with the relevant Union Harmonisation
Legislation: 2013/53/EU.
References to the relevant harmonised standards used or references to the other technical specifications in
relation to which conformity is declared: Conformity of the engines above is declared in accordance with Exhaust
Emissions Type Approval to 97/68/EC Stage 3a.
When installed in a watercraft, in accordance with the installation instructions accompanying the engine, the
engine will meet: The limits of Directive 97/68/EC as regards engines type approved in accordance with Directive
97/68/EC which are in compliance with Stage 3a emission limits for CI engines used in other applications than
propulsion of inland waterway vessels, locomotives and railcars, as provided for in point 4.2.1 of Annex I to that
Directive.
The engine must not be put into service until the watercraft into which it is to be installed has been declared in
conformity, if so required, with the relevant provision of this Directive.
I declare on behalf of the engine manufacturer that the engines are in conformity with the types for which above
mentioned EC type-examination certificates have been issued.
Signed for on behalf of Engines Plus Ltd
Name: Mr R Cantwell, Technical Director (Identification of the person empowered to sign on behalf of Date: 2017/01/03
the engine manufacturer or his authorised representative) Ref: RCD DofC 2013/53/EU Iss 2
Engine Model Engine Family EU Type Approval Certificate Nos.
Canaline 38 4A200 e4*97/68KA*2004/26*0130*02 Rev 01
Canaline 42 4A200 e4*97/68KA*2004/26*0130*02 Rev 01
Canaline 52 4A220 e4*97/68KA*2004/26*0131*02 Rev 01
Canaline 60 4B243 e4*97/68KA*2004/26*0134*01
Canaline 70T 4B243T e4*97/68JA*2004/26*0286*00
37
Emission Durability Statement for Recreational Craft Propulsion Engines
As referred to in Directive 2013/53/EU Annex 1/B/3
Provided engines are installed in accordance with the installation and maintenance instructions
contained in the Owner’s Manual, then engines will continue to comply with the Emission
Certification as specified in Directive 2013/53/EU Annex 1/B/2.2 throughout the normal life of
the engine and under normal conditions of use.
Normal life of the engine for CI engines in Directive 2013/53/EU Annex 1/B/3 is defined as 480
hours or 10 years, whichever occurs first.
Compliance will depend on many factors, such as Installation, Ventilation, Fuel and Lubricants,
Maintenance and the mode of operation and storage.
Fuels and Lubricants should conform to the specifications contained in the Owners Handbook.
Fuel settings on the engines are protected with Tamperproof Caps. Should any adjustment be
made to these settings, then Emissions Compliance, and compliance to the Directive will be
invalidated, as will any Warranty or Guarantee on the engine.
Exhaust systems are not generally supplied by Engines Plus Ltd, but must meet the
specifications in the Owners Handbook. Particular attention should be paid where multiple
bends, and especially elbows, are fitted. Allowance must be made for these. Back Pressures
stated should be measured at the Engine Exhaust Outlet Flange. This is at the Manicooler or,
where applicable, the Turbocharger Outlet.
To maintain the manufacturer’s Warranty, and Emission Compliance only Genuine Replacement
Parts should be used. It is the responsibility of the owner to ensure regular maintenance is
carried out competently, in accordance with the guidelines in the Owners Handbook
Where engines are to be unused for a period of more than 6 months, they should be “laid up”
according to the guidelines contained in the Owners Handbook. Failure to do so may lead to
deterioration of components, resulting in reduced performance, and possible non-compliance
of the Directive.
From experience of engines operating under the RCD over many years, with correct
maintenance and operation, we have found that performance is maintained, and durability will
far exceed that specified in the Directive.
Emissions Compliance Plate ~ attached to Rocker Cover.
Date: 2016/11/01
Ref: RCD Emission Durability 2013/53/EU Iss 1
38
Warranty Terms and Conditions INTRODUCTION
Your new Canaline Marine Engine is covered by the Engines Plus Ltd
warranty according to the conditions and instructions contained within this
document.
Engines Plus Ltd warranty covers only the engine and its ancillary parts.
The gearbox is covered by the gearbox manufacturer’s warranty.
OWNER’S OBLIGATIONS
The operation, maintenance and care of your Canaline Marine engine, in accordance
with the instructions and requirements listed in your Operators Manual, is your
responsibility. Records should be kept of all maintenance services performed,
including engine oil and filter changes. This record of correct maintenance is required
for the purpose of determining warranty coverage on repairs and should be
transferred to each subsequent owner.
It is your responsibility to ensure that the warranty registration is
completed (self-certification) and returned to Engines Plus Ltd, as this information forms part of the validation of your engine warranty.
The warranty registration must be returned completed to ensure the warranty on your engine is valid, this is the responsibility of the owner.
REPORT OF A DEFECT
It is the responsibility of the owner of any Canaline product referred to herein to
report any defect to Engines Plus Ltd, Distributor, Dealer, Workshop or Boat builder. Such a report must be made as soon as possible and no later than fourteen (14) days
from the date when the user first observed the defect.
WARRANTY TERMS AND CONDITIONS
1.0 In the event that Goods supplied are defective in that they have a defect that
existed at the time of delivery, Engines Plus Ltd shall (at its option) meet the cost of replacing or repairing such defective Goods or part thereof subject to the following:-
1.1 Labour costs will be paid in accordance with Engines Plus Ltd’s
standard repair times and standard rates, which are agreed upon
before work is carried out.
1.2 Engines Plus Ltd has the sole discretion to determine whether the
Goods shall be returned to Engines Plus Ltd’s premises or repaired
at any other location, which Engines Plus Ltd may nominate. 1.3 Engines Plus Ltd will pay for lubricating oil, coolant concentrate,
filter elements, belts, hoses, gaskets and other maintenance items
that are not reusable due to such defect. (at its discretion)
1.4 Only distributors, dealers or workshops authorized by Engines Plus Ltd may carry out warranty repairs.
39
1.5 No incidental, consequential or related costs such as costs for
travelling, transport, extra costs due to the installation in making
the products accessible, docking or cranes, loss of use, loss of
income, loss of time, loss of profits or damages of any other parts
or goods shall be payable under this condition 1.0 by Engines Plus
Ltd.
2.0 The warranty in condition 1.0 above does not cover Goods which in
Engines Plus Ltd’s opinion have been damaged during transportation,
installation or repair or through abnormal use, overload,
carelessness, insufficient lubrication, normal wear, use of spare parts
other than genuine parts approved by Engines Plus Ltd or through
any type of incorrect installation, abuse, misuse, accident or through
neglect or failure to follow instructions in the applicable owner’s
manual, maintenance instructions or installation instructions.
3.0 The warranty in condition 1.0 above will be void if You or your
representative, employees or contractors have taken abnormal risks or if modifications have been performed, which in the judgement of
Engines Plus Ltd have caused or enhanced the damage, or if the
security seals have been broken, or settings altered, or if the Goods or any part thereof have been used in violation of the law, or for an
unintended purpose.
4.0 The warranty does not cover expendable parts, such as all kinds of filters, belts, gaskets, rubber hoses, fuses, brushes, etc and
lubricants.
5.0 The operation, maintenance and care of the Goods in accordance
with the instructions and requirements listed in the owner’s manual and the warranty and service booklet provided by Engines Plus Ltd is
your responsibility. Records must be kept of all maintenance
services performed, including engine oil and filter changes. This
record of proper maintenance is required for the purpose of
determining warranty coverage on repairs and should be transferred
to each subsequent owner of the Goods.
6.0 All warranty claims must be advised to Engines Plus Ltd prior to work
being carried out, and an authorisation number being allocated, to
the distributors, dealer or authorized by Engines Plus Ltd workshop.
No claims for warranty will be accepted unless previously authorised
by Engines Plus Ltd.
40
7.0 The period of cover relating to the warranty in condition 1.0 above is
as follows:.
MULTIUSER or HIRE USE PRIVATE USE
Pleasure boats
The earlier of either
18 months from the date
of despatch from Engines
Plus Ltd’s factory
or
12 months or 2,000 hours
from engine installation
The earlier of either
42 months from the
date of despatch from
Engines Plus Ltd’s
factory
or
36 months or 1,500
hours from engine
installation
Pleasure boats Electrical equipment
and turbocharger
As above 12 months or 1,500
hours
Work boat engines and associated
products
The earlier of either
18 months from the date
of despatch from Engines Plus Ltd’s factory
or 12 months or 2,000 hours
The earlier of either 18 months from the
date of despatch from
Engines Plus Ltd’s factory
or 12 months or 2,000
hours
Gearbox This is covered by the gearbox manufacturer, please
consult the gearbox operators handbook
8.0 Save where the Goods are sold to a person dealing as a consumer
(within the meaning of the Unfair Contract Terms Act 1977) all
warranties conditions or other terms implied by law or custom are
excluded to the fullest extent permitted by law.
9.0 Engines Plus Ltd shall under no circumstances be liable for any
indirect or consequential loss, loss of profits, loss of savings, loss of
business or loss of contract. Engines Plus Ltd’s liability whether in
contract, tort (including negligence), breach of statutory duty or
otherwise shall not exceed the price of the Goods in respect of which
any claim arises PROVIDED THAT nothing in these Conditions shall
restrict or exclude Engines Plus Ltd’s liability for death or personal
injury caused by its negligence.
41
Service Record
Proof of Service – 50 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 250 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 450 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 650 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 850 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 1050 Hour Actual Engine Hours:
Date:
Dealer:
Proof of Service – 1250 Hour Actual Engine Hours:
Date:
Dealer:
42
43
ENGINES PLUS LTD
Unit F The Aquarius Centre
Edison Close
Waterwells Business Park
Quedgeley
Gloucestershire
GL2 2FN
Tel: 01452 729707 E-mail – [email protected]
www.canaline-engines.co.uk
EP910541