Upload
ngotram
View
217
Download
2
Embed Size (px)
Citation preview
a
Camera EI3 Extender Board Manual an EZ-Extender® product
Revision 1.0, August 2012
Part Number 82-000351-01
Analog Devices, Inc.One Technology WayNorwood, Mass. 02062-9106
Copyright Information©2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc.
Printed in the USA.
DisclaimerAnalog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by impli-cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark NoticeThe Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Board, EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of their respective owners.
Regulatory Compliance The Camera EI3 Extender Board is designed to be used solely in a labora-tory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices.
The Camera EI3 Extender Board is in the process of being certified to comply with the essential requirements of the European EMC directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE” mark.
The extender board contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused extender boards in the protective shipping package.
CONTENTS
PREFACE
Product Overview ........................................................................ vii
Purpose of This Manual .............................................................. viii
Intended Audience ...................................................................... viii
Manual Contents .......................................................................... ix
What’s New in This Manual .......................................................... ix
Technical Support .......................................................................... x
Supported Products ....................................................................... xi
Product Information ..................................................................... xi
Analog Devices Web Site ......................................................... xi
EngineerZone ......................................................................... xii
Related Documents ..................................................................... xiii
USING CAMERA EI3 EXTENDER BOARD
Package Contents .......................................................................... 1-2
Supported Operating Systems ........................................................ 1-2
System Requirements .................................................................... 1-3
Camera EI3 Extender Board Installation ........................................ 1-3
Aptina CMOS Sensor Interface ..................................................... 1-4
Camera EI3 Extender Board Manual v
Contents
Expansion Interface III ................................................................. 1-5
Example Programs ........................................................................ 1-6
Board Design Database ................................................................. 1-6
CAMERA EI3 EXTENDER BOARD HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Jumpers ........................................................................................ 2-3
Camera Width Jumper (JP1) ................................................... 2-3
Connectors ................................................................................... 2-4
Expansion Interface III (EI3) Connector (J1) ........................... 2-5
Sensor Connector (J2) ............................................................. 2-5
Sensor Connector (J3) ............................................................. 2-5
Power Connector (P4) ............................................................. 2-6
CAMERA EI3 EXTENDER BOARD BILL OF MATERIALS
CAMERA EI3 EXTENDER BOARD SCHEMATIC
INDEX
vi Camera EI3 Extender Board Manual
PREFACE
Thank you for purchasing the Camera EI3 Extender Board, an
EZ-Extender® product for EZ-KIT Lite®/EZ-Board® evaluation systems with the expansion interface 3 (EI3).The EZ-KIT Lite/EZ-Board and Camera EI3 Extender Board are designed to be used in conjunction with the CrossCore® Embedded Studio (CCES) development environment.
To learn more about Analog Devices development software, go to http://www.analog.com/dsp/tools.
Product OverviewThe Camera EI3 Extender Board is a separately sold daughter board that plugs onto the expansion interface 3 (EI3) of an EZ-KIT Lite/EZ-Board evaluation system. The extender board aids the design and prototyping phases of embedded processor-targeted applications.
The board extends the capabilities of the evaluation system by providing a connection between the parallel peripheral interface (PPI) of the processor and an Aptina CMOS sensor headboard. The two-wire interface (TWI) port of the processor is used to communicate to the CMOS sensor on the extender.
Camera EI3 Extender Board Manual vii
Purpose of This Manual
The following is a list of the Camera EI3 Extender Board interfaces.
• Video interface
• Connects to Aptina headboards
• Video connectors
• One 13 × 2 IDC for 8-, 10- and 12-bit sensors
• One 13 × 1 IDC for 12-bit sensors; used in conjunction with the 13 × 2 connector
• No power supply required: derives power from the EZ-KIT Lite/EZ-Board
• Jumper for selecting CMOS sensor bus width
• CE certified
Purpose of This ManualThe Camera EI3 Extender Board Manual provides instructions for install-ing the product hardware (board). The text describes operation and configuration of the board components and provides guidelines for run-ning your own code on the Camera EI3 Extender Board. Finally, a schematic and a bill of materials are provided for reference.
Intended AudienceThe primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture, instruction set, and C/C++ programming languages.
viii Camera EI3 Extender Board Manual
Preface
Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts that describe your target architecture and hardware development tools.
Programmers who are unfamiliar with the CrossCore Embedded Studio programming environment or the mating evaluation board should refer to the CCES online help.
Manual ContentsThe manual consists of:
• Chapter 1, “Using Camera EI3 Extender Board” on page 1-1 Provides basic product information.
• Chapter 2, “Camera EI3 Extender Board Hardware Reference” on page 2-1 Provides information about the product’s hardware components.
• Appendix A, “Camera EI3 Extender Board Bill Of Materials” on page A-1 Provides a list of hardware components used to manufacture the board.
• Appendix B, “Camera EI3 Extender Board Schematic” on page B-1 Provides all circuits on the extender board.
What’s New in This ManualThis is the first revision of the Camera EI3 Extender Board Manual.
Camera EI3 Extender Board Manual ix
Technical Support
Technical SupportYou can reach Analog Devices processors and DSP technical support in the following ways:
• Post your questions in the processors and DSP support community at EngineerZone®: http://ez.analog.com/community/dsp
• Submit your questions to technical support directly at: http://www.analog.com/support
• E-mail your questions about processors, DSPs, and tools develop-ment software from CrossCore Embedded Studio or VisualDSP++®:
Choose Help > Email Support. This creates an e-mail to [email protected] and automatically attaches your CrossCore Embedded Studio or VisualDSP++ version infor-mation and license.dat file.
• E-mail your questions about processors and processor applications to: [email protected] or [email protected] (Greater China support)
• In the USA only, call 1-800-ANALOGD (1-800-262-5643)
• Contact your Analog Devices sales office or authorized distributor. Locate one at: www.analog.com/adi-sales
x Camera EI3 Extender Board Manual
Preface
• Send questions by mail to: Processors and DSP Technical Support Analog Devices, Inc. Three Technology Way P.O. Box 9106 Norwood, MA 02062-9106 USA
Supported ProductsThis extender board supports EZ-KIT Lite/EZ-Board evaluation systems with the expansion interface 3.
Product InformationProduct information can be obtained from the Analog Devices Web site and the CCES online help system.
Analog Devices Web SiteThe Analog Devices Web site, www.analog.com, provides information about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors.
To access a complete technical library for each processor family, go to http://www.analog.com/processors/technical_library. The manuals selection opens a list of current manuals related to the product as well as a link to the previous revisions of the manuals. When locating your manual title, note a possible errata check mark next to the title that leads to the current correction report against the manual.
Also note, myAnalog is a free feature of the Analog Devices Web site that allows customization of a Web page to display only the latest information
Camera EI3 Extender Board Manual xi
Product Information
about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. myAnalog provides access to books, application notes, data sheets, code examples, and more.
Visit myAnalog (found on the Analog Devices home page) to sign up. If you are a registered user, just log on. Your user name is your e-mail address.
EngineerZoneEngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://ez.analog.com to sign up.
xii Camera EI3 Extender Board Manual
Preface
Related DocumentsFor additional information about the processor, refer to the following publications.
Table 1. Related Processor Publications
Title Description
Processor Data Sheet General functional description, pinout, and timing of the processor
Processor Hardware Reference Description of the internal processor archi-tecture and all register functions
Blackfin Processor Programming Reference Description of all allowed processor assembly instructions
Camera EI3 Extender Board Manual xiii
1 USING CAMERA EI3 EXTENDER BOARD
This chapter provides the setup procedure for the Camera EI3 Extender
Board and describes the interfaces the extender supports.The information is presented in the following order.
• “Package Contents” on page 1-2
• “Supported Operating Systems” on page 1-2
• “System Requirements” on page 1-3
• “Camera EI3 Extender Board Installation” on page 1-3
• “Aptina CMOS Sensor Interface” on page 1-4
• “Expansion Interface III” on page 1-5
• “Example Programs” on page 1-6
• “Board Design Database” on page 1-6
Camera EI3 Extender Board Manual 1-1
Package Contents
Package ContentsYour Camera EI3 Extender Board package contains the following items.
• Camera EI3 Extender Board
• A bag containing hardware for securing the extender board on the EZ-KIT Lite/EZ-Board
• Release note containing information about the product download
Contact the vendor where you purchased your extender board or contact Analog Devices, Inc. if any item is missing.
Supported Operating SystemsCCES is supported on the following operating systems:
• Windows® XP Professional SP3 (32-bit only)
• Windows Vista™ Business, Enterprise, or Ultimate SP2 (32-bit only)
• Windows 7 Professional, Enterprise, or Ultimate (32- and 64-bit)
Windows Vista and Windows 7 users may experience User Access Control (UAC) related errors if the software is installed into a pro-tected location, such as Program Files or Program Files (x86). We recommend installing the software in a non-UAC-protected location.
1-2 Camera EI3 Extender Board Manual
Using Camera EI3 Extender Board
System RequirementsVerify that your PC has these minimum requirements for the CCES installation:
• 2 GHz single-core processor
• 1 GB RAM
• 8 GB available disk space
• One open USB port
A faster disk drive decreases the build time, especially for a large amount of source files.
Camera EI3 Extender Board InstallationFollow these instructions to ensure correct operation of the product hardware and software.
1. Attach the extender board to the EZ-KIT Lite/EZ-Board. The J1 connector on the extender board can be connected to the P1A, P2A, or P3A connector on the EZ-KIT Lite/EZ-Board. Refer to the example program for a reference to the proper connector.
2. Use the provided hardware to secure the extender to the EZ-KIT Lite/EZ-Board. See Figure 1-1.
3. Refer to the EZ-KIT Lite/EZ-Board manual for information on connecting to a personal computer (PC) and running CCES.
Camera EI3 Extender Board Manual 1-3
Aptina CMOS Sensor Interface
Aptina CMOS Sensor InterfaceThe Camera EI3 Extender Board supports interfacing with Aptina CMOS sensor headboards that have an 8-, 10- or 12-bit interface. Both image processors/SOC and sensor headboards are supported.
The interface width is configured via a jumper. Refer to “Jumpers” on page 2-3 for more information.
For more information about Aptina CMOS sensors, go to www.aptina.com.
Figure 1-1. Assembled Board Diagram
Part DescriptionItem0.75in Nylon Standoff1
1.0in Nylon Standoff2 1.25in Nylon Standoff3
3
Nylon Screw4 Nylon Spacer5
EZ-Extender 3(Stacked)
2
2
1
1
2
4
5
4 4
4
5
1-4 Camera EI3 Extender Board Manual
Using Camera EI3 Extender Board
An example program demonstrating capabilities via a M114 headboard is available by installing the Camera EI3 Extender Board Support Package (BSP). The headboard can be purchased through C4AV.com using part number MT9M114EBLSTCZH ES.
Expansion Interface IIIThe Expansion Interface III (EI3) allows an extender board to be tested across various hardware platforms that have the same expansion interface connectors.
The EI3 implemented on the Camera EI3 Extender Board contains the PPI and TWI ports. These signals are used for the peripheral on the extender. For pinout information, go to Appendix B, “Camera EI3 Extender Board Schematic”. The mechanical dimensions of the expansion connectors can be obtained by contacting “Technical Support”.
The Camera EI3 Extender Board supports interfacing with EZ-Boards which are operating at an IO voltage of 3.3V. Other IO voltages are not supported.
The Camera EI3 Extender Board supports being powered from either the EZ-Board or through the on-board 5V power connector (P1).
For more information about other daughter boards, visit the Analog Devices Web site at www.analog.com/processors/tools/blackfin.
Limits to current and interface speed must be taken into consideration when using the EI3. Current for the EI3 can be sourced from the EZ-KIT Lite/EZ-Board; therefore, the current should be limited to 200 mA for 5V and 300 mA for the 3.3V planes.
Camera EI3 Extender Board Manual 1-5
Example Programs
If more current is required, then a separate power connector and a regula-tor must be designed on the daughter card. Additional circuitry can add extra loading to signals, decreasing their maximum effective speed.
Analog Devices does not support and is not responsible for the effects of additional circuitry.
Example ProgramsExample programs are included with the Camera EI3 Extender Board Support Package (BSP). Example programs demonstrate various capabili-ties of the product. The support package is installed on top of CCES. Once installed, the example programs can be found in the following directory:
<install_path>/Camera_EI3_Extender_Board-RelX.X.X/Camera_EI3
where X.X.X denotes the support package release number.
Board Design DatabaseA .zip file containing all of the electronic information required for the design, layout, fabrication and assembly of the product is available for download from the Analog Devices board design database at www.analog.com/board-design-database.
1-6 Camera EI3 Extender Board Manual
2 CAMERA EI3 EXTENDER BOARD HARDWARE REFERENCE
This chapter describes the hardware design of the Camera EI3 Extender
Board.The following topics are covered.
• “System Architecture” on page 2-2 Describes the daughter board configuration and explains how the board components interface with the processor and EZ-KIT Lite.
• “Jumpers” on page 2-3 Describes jumper functionality.
• “Connectors” on page 2-4 Shows the locations and provides part numbers for the on-board connectors. In addition, the manufacturer and part number infor-mation is provided for the mating parts.
Camera EI3 Extender Board Manual 2-1
System Architecture
System ArchitectureA block diagram of the Camera EI3 Extender Board is shown in Figure 2-1.
Figure 2-1. Camera EI3 Extender Board Block Diagram
PPITWI
2-2 Camera EI3 Extender Board Manual
Camera EI3 Extender Board Hardware Reference
JumpersThis section describes jumper functionality. The jumper on the Camera EI3 Extender Board is located on the back of the board.
Camera Width Jumper (JP1)The camera width jumper (JP1) determines whether the interface to the processors PPI is 8, 10 or 12 bits. The camera width is chosen by placing the jumper in the appropriate position. By default, 8-bit mode is selected since that is the interface that is on the M114 headboard.
Camera Mode Shunt
8-bit 1 and 2 (default)
10-bit 3 and 4
12-bit 5 and 6
Camera EI3 Extender Board Manual 2-3
Connectors
ConnectorsThis section describes connector functionality and provides information about mating connectors. Figure 2-2 shows the locations of all connectors on the Camera EI3 Extender Board.
Figure 2-2. Connector and Jumper Locations
2-4 Camera EI3 Extender Board Manual
Camera EI3 Extender Board Hardware Reference
Expansion Interface III (EI3) Connector (J1)One board-to-board connector (J1) provides signals from the PPI and TWI ports of the processor. The connector is located on the top side of the board.
Sensor Connector (J2)The sensor connector (J2) is a 13 × 2 IDC connector which connects with an Aptina headboard directly or through a cable. This connector can be used for interfacing with Aptina CMOS sensor headboards with an 8-, 10- and 12-bit interface. The connector is located on the bottom side of the board
Sensor Connector (J3)The sensor connector (J3) is a 13 × 1 IDC connector which connects with an Aptina headboard directly or through a cable. This connector is used for interfacing with Aptina CMOS sensor headboards with a 12-bit inter-face. The connector is located on the bottom side of the board
Part Description Manufacturer Part Number
120-pin, 0.6 mm HIROSE FX8-120S-SV(21)
Mating Connector
120-pin, 0.6 mm HIROSE FX8-120P-SV1(91)
Part Description Manufacturer Part Number
.025 SQ POST SOCKET 3M 8526-4500PL
Part Description Manufacturer Part Number
.025 SQ POST SOCKET SAMTEC SSW-113-01-T-S
Camera EI3 Extender Board Manual 2-5
Connectors
Power Connector (P4)Under normal circumstances, the power connector is not needed because the Camera EI3 Extender Board derives its power from the EZ-KIT Lite/EZ-Board. If the EZ-KIT Lite/Camera EI3 Extender Board is not able to supply enough power to the Camera EI3 Extender Board, then an external power supply can be connected to P4 which will power the Cam-era EI3 Extender Board and EZ-KIT Lite/EZ-Board. The connector is located on the bottom side of the board.
Part Description Manufacturer Part Number
0.65 mm power jack CUI 045-0883R
Mating Cable
[email protected] power supply GLOBETEK GS-1750(R)
2-6 Camera EI3 Extender Board Manual
A CAMERA EI3 EXTENDER BOARD BILL OF MATERIALS
The bill of materials corresponds to “Camera EI3 Extender Board Schematic”
on page B-1.Ref. Qty. Description Reference Designator
Manufacturer Part Number
1 1 27MHZ OSC003 U4 EPSON SG-8002CA-MP
2 3 SN74LVC16T245 TVSOP48 U1-U3 DIGI-KEY 296-21052-1-ND
3 1 PWR .65MM CON027 P4 DIGI-KEY CP1-022PJCT-ND
4 1 1A RESETABLE 1206 F1 RAYCHEM NANOSMDC110F-2
5 1 IDC 3X2 IDC3X2 JP1 BURG 54102-T08-03LF
6 1 .6MM 120PIN HIROSE_FX8-120S-SV(21)
J1 HIROSE FX8-120S-SV(21)
7 1 IDC 13X2 IDC13X2 J2 SAMTEC SSW-113-01-T-D
8 1 IDC 13X1 IDC13X1 J3 SAMTEC SSW-113-01-T-S
9 4 10UF 6.3V 10% 0805 C2,C3,C16,C17
AVX 08056D106KAT2A
10 13 0.1UF 10V 10% 0402 C1,C4-C15 AVX 0402ZD104KAT2A
11 3 10K 1/16W 5% 0402 R2-R4 VISHAY CRCW040210K0FKED
12 2 33 1/16W 5% 0402 R1,R5 VISHAY CRCW040233R0JNEA
13 3 1A MBR130LSFT1G SOD-123FL
D1-D3 ON SEMI MBR130LSFT1G
Camera EI3 Extender Board Manual A-1
0.11 3
A0351-2012
Camera EI3 Extender BoardTitle Sheet
2/28/12
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
Camera EI3 Extender BoardSCHEMATIC
0.12 3
A0351-2012
Camera EI3 Extender BoardConnectors
2/28/12
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
C1
04020.1UF
3.3V
U4
OSC00327MHZ
4
31
2GND
OE OUT
VDD
3.3V
R1330402
J2
IDC13X2
5
1
18
20
22
26
24
16
14
12
25
23
21
19
17
15
13
11
9
3
6
10
8
4
2
7
VCC
J1
HIROSE_FX8-120S-SV(21)
101
100
71
70
120
118
116
114
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
6867
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
53
51
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38SPI0_SEL_CSPI0_SEL_B
SPORT1_D1
SPORT0_TDV
PPI0_FS1
RSVD5
GND6
RSVD2
PPI0_D3
GND5
PPI0_D9
PPI0_D13
SPORT0_D1
SPORT1_TDV
GND7
PPI0_FS3
RSVD4
PPI0_D11
RSVD3
PPI0_D1
PPI0_D5
PPI0_D7
SPI0_D2 SPI0_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI0_RDY
GND11
RSVD8
TWI0_A0*
SPI0_SEL1/SPI0_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD6
RSVD7
RSVD9
RESET_IN*
UART0_RX
PPI0_D17
PPI0_D14
VIN
GND1
USB_VCC
PPI0_D23
PPI0_D19
RSVD1
GND2
GND3
PPI0_D21
SPORT_INT
GND8
UART0_TX
GND4
WAKE*
GND13
EXT_BOOT
SLEEP*
RSVD11 RSVD12
RSVD10
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI0_MISO
SPI0_SEL_A
SPORT0_CLK
SPORT0_FS
SPORT1_D0
GND18
PPI0_FS2
RSVD15
PPI0_INT
PPI0_D4
PPI0_D6
PPI0_D10
GND21
PPI0_D16
PPI0_D20
GND22
GND23
RSVD17
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI0_CLK
SPI0_MOSI
GND17
SPORT0_D0
SPORT1_FS
SPORT1_CLK
PPI0_CLK
RSVD14
GND19
PPI0_D2
GND20
PPI0_D8
PPI0_D12
PPI0_D15
PPI0_D18
PPI0_D22
VIO
GND24
PS_IN
RSVD13
CLKOUT
RSVD16
PPI0_D0
C210UF0805
C3
080510UF
3.3V
VCC
PWR_IN
IDC13X1
J3
13
12
11
10
9
8
6
7
5
1
2
3
4
C1610UF0805
3.3V
C1710UF0805
VCC
F1
12061A
D1
SOD-123FLMBR130LSFT1G
D2
MBR130LSFT1GSOD-123FL
D3
SOD-123FLMBR130LSFT1G
PWR_IN
P4
CON0275V
1
2
3
PPI_FS1
PPI_FS2
RESETRESET
SCL
SCL
SDA
SDA
APTINA_MSB-7
PPI_D1
PPI_D2 PPI_D3
PPI_D4
PPI_D0
PPI_D5
PPI_D6 PPI_D7
APTINA_FS2
PPI_D8 PPI_D9
PPI_D10 PPI_D11
APTINA_MSB-6
APTINA_MSB-5 APTINA_MSB-4
APTINA_MSB-3 APTINA_MSB-2
APTINA_MSB-1 APTINA_MSB
APTINA_MSB-9 APTINA_MSB-8
APTINA_MSB-10
APTINA_MSB-11
PPI_CLK
APTINA_CLK
APTINA_FS1
VIN
VIN
USB_VCC
USB_VCC
0.13 3
A0351-2012
Camera EI3 Extender BoardConfiguration
2/28/12
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
3.3V
SN74LVC16T245TVSOP48
U1
19
17
16
14
13
30
32
33
35
36
12
11
9
8
6
5
3
2
37
38
40
41
43
44
46
471A1
1A2
1A3
1A4
1A5
1A6
1A7
1A8
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1DIR1
2A1
2A2
2A3
2A4
2A5
2A629
2A727
2A826
2DIR24
VCCA_131
VCCA_242
1OE48
2OE25
2B1
2B2
2B3
2B4
2B620
2B5
2B722
2B823
VCCB_17
VCCB_218
SN74LVC16T245TVSOP48
U2
18
7
23
22
19
20
17
16
14
13
25
48
42
31
24
26
27
29
30
32
33
35
36
1
12
11
9
8
6
5
3
2
37
38
40
41
43
44
46
471A1
1A2
1A3
1A4
1A5
1A6
1A7
1A8
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1DIR
2A1
2A2
2A3
2A4
2A5
2A6
2A7
2A8
2DIR
VCCA_1
VCCA_2
1OE
2OE
2B1
2B2
2B3
2B4
2B6
2B5
2B7
2B8
VCCB_1
VCCB_2
3.3V 3.3V
SN74LVC16T245TVSOP48
U3
18
7
23
22
19
20
17
16
14
13
25
48
42
31
24
26
27
29
30
32
33
35
36
1
12
11
9
8
6
5
3
2
37
38
40
41
43
44
46
471A1
1A2
1A3
1A4
1A5
1A6
1A7
1A8
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
1DIR
2A1
2A2
2A3
2A4
2A5
2A6
2A7
2A8
2DIR
VCCA_1
VCCA_2
1OE
2OE
2B1
2B2
2B3
2B4
2B6
2B5
2B7
2B8
VCCB_1
VCCB_2
R5
040233
JP1
IDC3X2
1
3
65
4
2
3.3V
R310K0402
3.3V
10K0402
R2 R410K0402
C40.1UF0402
C5
04020.1UF
C60.1UF0402
C7
04020.1UF
C80.1UF0402
3.3V
C9
04020.1UF
C10
04020.1UF
C110.1UF0402
C12
04020.1UF
C130.1UF0402
C140.1UF0402
3.3V
C15
04020.1UF
PPI_FS1
PPI_FS2
APTINA_MSB-7
APTINA_MSB-7
APTINA_MSB-7
PPI_D1PPI_D1PPI_D1
PPI_D2PPI_D2PPI_D2
PPI_D3PPI_D3PPI_D3
PPI_D4PPI_D4PPI_D4
PPI_D0PPI_D0PPI_D0
PPI_D5PPI_D5PPI_D5
PPI_D6PPI_D6PPI_D6
PPI_D7PPI_D7PPI_D7
APTINA_FS2
PPI_D8PPI_D8
PPI_D9PPI_D9
PPI_D10
PPI_D11
APTINA_MSB-6
APTINA_MSB-6
APTINA_MSB-6
APTINA_MSB-5
APTINA_MSB-5
APTINA_MSB-5
APTINA_MSB-4
APTINA_MSB-4
APTINA_MSB-4
APTINA_MSB-3
APTINA_MSB-3
APTINA_MSB-3
APTINA_MSB-2
APTINA_MSB-2
APTINA_MSB-2
APTINA_MSB-1
APTINA_MSB-1
APTINA_MSB-1
APTINA_MSB
APTINA_MSB
APTINA_MSB
APTINA_MSB-9
APTINA_MSB-9
APTINA_MSB-8
APTINA_MSB-8 APTINA_MSB-10
APTINA_MSB-11
PPI_CLK APTINA_CLK
APTINA_FS1
10_BIT_MODE
10_BIT_MODE
8_BIT_MODE
8_BIT_MODE 12_BIT_MODE
12_BIT_MODE
Jumper Mode
1&2
3&4
5&6
8-bit
10-bit
12-bit
I INDEX
A E
Aptina CMOS sensor interface, 1-4architecture, of Camera EI3 Extender Board,2-2assembled board diagram, 1-4
Bbill of materials, A-1block diagram
assembled board, 1-4Camera EI3 Extender Board, 2-2
board design, 1-6board schematic (Camera EI3 Extender Board),
B-1
Ccamera width jumper (JP1), 2-3connectors, 2-4
diagram of locations, 2-4IDC, 2-5J1 (EI3), 2-5J2 (sensor), 2-5J3 (sensor), 2-5P4 (power), 2-6
contents, of this Extender Board package, 1-2
EngineerZone, xiiexpansion interface III (EI3)
connector (J1), 2-5overview, 1-5
extender board block diagram, 2-2
IIDC connector, 2-5installation, of this Extender Board, 1-3
Jjumpers, 2-3
camera width (JP1), 2-3diagram of locations, 2-4
Ooperating systems, supported, 1-2
Ppackage contents, 1-2power
connector (P4), 2-6product overview, vii
Camera EI3 Extender Board Manual I-1