PAGE 202 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

ch

ok

e t

ub

es

sho

tg

un

shotgun InDeXChoke Tubes . . . . . . . . . . . . . . . . . . . 202-204 Replacement Parts . . . . . . . . . . . . . . 206-208

Competition Gear . . . . . . . . . . . . . . .216-217 Stocks . . . . . . . . . . . . . . . . . . . . . . . . .211-216

Magazine Tubes & Parts . . . . . . . . 208-211 Tactical Accessories . . . . . . . . . . . . . . . . .218

Performance Parts. . . . . . . . . . . . . .204-206

Non-evaporating, metallic base, anti-seize lubricant pre-vents corrosion and galling caused by high pressure loads and extreme temperatures. abSPECS: A squeeze tube, net wt. 3/4 oz. (21 g).

BIRCHWOOD CASEY

CHOKE TUBE LUBEEliminates Stuck Choke Tubes, Barrel Damage

#167-400-150AQ Choke Tube Lube, 1K4N39 � � � � � � � � � � $ 7.99 - 3 or More - Choke Tube Lube, per each, 1K3J87 � �$ 7.20

Aluminum fingers accurately align the wrench inside the tube and hold the teeth in

place. Crank handle quickly spins tubes in or out. Fits factory choke tubes and Briley X-2 tubes. (Not for Briley special thinwall tubes.) ab

SPECS: Plastic knob, aluminum fingers/handle, stainless steel body.

BRILEY CHOKE TUBE SPEED WRENCHSpeed & Leverage

To Quickly Remove Tubes

#129-070-012AQ 12 Gauge Tube Wrench, 9B24G81 � � $ 28.99#129-070-020AQ 20 Gauge Tube Wrench, 9B24P81 � � 28.99

abcARLson’s unIVeRsAL WRench - Fits all of the most popular brands of choke tubes.SPECS: Steel, blued. 2" (5cm) long. 12 or 20 ga. only.#155-100-012AQ 12 Ga� Univ� Choke Wrench,

5E12M50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 14.99#155-100-020AQ 20 Ga� Univ� Choke Wrench,

5E12A50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14.99

cARLson’s unIVeRsAL choke tube WRench - Stronger, and a lot easier on your choke tubes and your fin-gers, than a quarter. Fits virtually every choke tube slot. Includes key chain.SPECS: Stainless steel, 21/2" (6.3cm) long with 6" chain.#155-103-000AQ Universal Choke Wrench, 5E2Q97� � � $ 4.99

cARLson’s sPoRtIng cLAYs sPeeD WRench - Crank and handle provide both speed and leverage for quickly removing choke tubes. Large, easy-to-grip knob expands the vinyl, non-marking grip-ping surface that’s inserted into the tube.SPECS: Plastic knob. Aluminum shaft and handle.#155-102-020AQ 20 Ga� S/C Speed Wrnch, 5E13E69 � � $ 20.49#155-102-012AQ 12 Ga� S/C Speed Wrnch, 5E13L69 � � 20.49

CARLSON’S CHOKE TUBE WRENCH

“Ears” give the leverage needed to unscrew tight choke tubes damage-free. Good control for installation, too. Sized to fit Colonial brand tubes; fits many others. Pocket-sized. abSPECS: Steel. 21/2" (6.3cm) l, 11/4" (3.2cm) w, .059" (1.5mm) thick.

COLONIAL ARMS

CHOKE TUBE WRENCHA Quarter With Guts!

#198-100-001AQ Choke Tube Wrench, 8A2F05 � � � � � � � $ 2.95

Handy, fluted aluminum handle with one Phillips and four of Magna-Tip hollow

ground slotted bits; all stored right in the handle, always avail-able when you need them. 3" length gives excellent control; keeps your hand close to the work and helps prevent dam-age to screw slots. Quick-change, magnetic bit retainer also keeps small screws from getting lost. 2" magnetic extension provides extra reach. Accepts the Magna-Tip universal choke tube wrench, sold separately. abSPECS: Aluminum handle, green. 3" (7.6cm) overall length, 1" (2.5cm) diameter. Accepts all Brownells 1/4" hex drive bits. 1" long bits - 445-1, 445-2, 445-3, 445-4 and 440-2 Phillips. Choke Wrench Bit - 7/8" (22.2mm) diameter, 11/2" (3.8cm) long.

DESIGNATED DRIVERA Screwdriver Kit For Your

Pocket, Tool Box & Range Bag

#080-000-023AQ Designated Driver, 1E22J91 � � � � � � � � $ 29.99

If a barrel is too thin to tap for screw-in choke tubes or it’s chrome-lined (eats reamers/taps), or if the end has been bulged, you can install screw-in tubes. Simply turn the last 3/4" of barrel to dimension in chart and solder adapter in place. abSPECS: Alloy steel. 21/2" (6.3cm) lg. 12 Ga. .867" (22mm) O.D. Accepts Win-Choke®-style tubes (Colonial “Invisible” Tubes). Maximum bore di-ameter .735".

SCREW-IN

CHOKE ADAPTERLets “Too-Thin” Barrels

Accept Win-Choke®-Style Tubes

stock # thReAD FIts bbL tuRneD to gAuge#514-132-795AQ .812"-32 .795 12#514-132-812AQ .812"-32 .812 12#514-132-825AQ .812"-32 .825 12#514-132-840AQ .812"-32 .840 12

— Advise # — Screw-In Choke Adapter, 8A16H38 � � � $ 21.85

Brownells partnered with Carl-son’s to develop a set of 12 gauge choke tubes specifically optimized for 3-Gun competition. Having one of these sets in your range bag ensures you’re equipped with the

exact constriction for any stage, from flying clay pigeons to a troublesome marker next to a “no-shoot.” Each set includes Improved Cylinder for close-range targets, Modified for mid-range, and Full for long-distance. These tubes are designed to throw tighter and denser patterns than conventional tubes, so be sure to pattern your shotgun with the shotshell load you plan to use to be sure you know the results you’ll get with each of these tubes. Knurled rings give plenty of grasping surface for quick removal, and the constriction is laser marked on the end and body for easy reference. Can be used with lead, steel, or Hevi-Shot. abSPECS: 17-4 stainless steel, matte black. 12 gauge only. Remington – 2.875" (7.3cm) long. Fits most Remington shotguns. Winchester/Brown-ing Invector/Mossberg – 2.35" (5.97cm) long. Fits Winchester, Browning Invector, Mossberg 500, Weatherby, and Savage. Benelli Crio® Plus – 3.75" (9.525cm) long. Fits Benelli Crio Plus choke system, including Super Black Eagle II, CrioTech M2 and other models. All models for 12 gauge only. Do not use slugs, sabots, or rifled slugs in constrictions tighter than Improved Cylinder, and do not shoot steel shot larger than BB or any steel load faster than 1,550 feet per second through the Full.

/CARLSON’S

3-GUN CHOKE TUBE SETSThree Different Constrictions So You’re Ready For Any Stage

Of Competition

#155-000-220AQ Remington 3-Gun Choke Tube Set, 5E86F07 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 89.99

#155-000-219AQ Win/Brng Invector/Moss 3-Gun Choke Tube Set, 5E86F07 � � � � � � � � � � 89.99

#155-000-221AQ Benelli Crio Plus 3-Gun Choke Tube Set, 5E86N07 � � � � � � � � � � � � � � � � � 89.99

WIN-CHOKE® or TRU-CHOKE™-STYLE TUBES, WHICH SHOULD I THREAD BARRELS FOR?

Win-Choke®-style tubes are thicker and gener-ally more available. Tru-Choke™ Standard-style tubes are thinner, and the Tru-Choke™ Thinwall-style tubes thinner yet, so a far wider range of barrels can be threaded to ac-cept them. But, they are less available. Ideally, you would have tooling for all three styles and thread barrels for: Win-Choke®-style tubes when they are thick enough; Tru-Choke™ Standard-style on thinner barrels; Tru-Choke™ Thinwall-style tubes on the thinnest 12 ga. side-by-side and over-under barrels. But, that’s a lot of money. So, mea-sure the barrels of commonly used shotguns in your area, check “Screw-In Choke Installation Requirements” and buy the tooling that will convert the most guns.

Choke constrictions, from Cyl-inder to X-Full let you precisely

match your load to the shooting conditions. Long tube extends beyond the length of the muzzle, features highly polished inte-rior for less pellet deformation; reduced fliers and tighter pat-terns. Knurled grasping band speeds installation and removal. Choke constriction is marked on band, no need to remove tube to verify size. abSPECS: 17-4 stainless steel. Polished, bright finish. Extends beyond muz-zle approx. .812" (20.6mm). Use with lead and bismuth shot. Steel shot can be used with constrictions of Modified and larger. Beretta chokes will not fit guns with Optima choke thread.

BROWNING INVECTOR PLUS

stk# 12 gA. stk# 20 gA. choke#129-000-206AQ #129-000-207AQ Cylinder#129-005-001AQ #129-006-001AQ Skeet#129-005-002AQ #129-006-002AQ Imp Cyl#129-005-003AQ NA Lt Mod#129-005-004AQ #129-006-004AQ Mod#129-005-005AQ NA Imp Mod#129-005-006AQ NA Lt Full#129-005-007AQ NA Full#129-005-008AQ NA X-Full

— Advise # — Invector Plus Choke Tube, 9B38C53 � � $ 43.99

REMINGTON

stk# 12 gA. stk# 20 gA. choke#129-015-003AQ NA Lt Mod#129-015-004AQ #129-016-004AQ Mod#129-015-005AQ NA Imp Mod#129-015-007AQ #129-016-007AQ Full

— Advise # — Remington Choke Tube, 9B38P53 � � � � $ 43.99

BERETTA & BENELLI 12 GAUGE

stk# beRettA 12 gA.

stk# beneLLI 12 gA. choke

#129-025-001AQ #129-025-001AQ Skeet#129-025-002AQ #129-025-002AQ Imp Cyl#129-025-003AQ #129-025-003AQ Lt Mod#129-025-005AQ #129-025-005AQ Imp Mod#129-025-006AQ #129-025-006AQ Lt Full

BRILEY X-2 SCREW-IN

X-2 SCREW-IN CHOKE TUBEExtended Length,

Competition Grade Tubes Improve Pattern & Accuracy

BROWNING INVECTOR

stk# 12 gA. stk# 20 gA. choke#129-001-001AQ #129-002-001AQ Skeet#129-001-002AQ #129-002-002AQ Imp Cyl#129-001-003AQ NA Lt Mod#129-001-004AQ #129-002-004AQ Mod#129-001-005AQ NA Imp Mod#129-001-007AQ NA Full

— Advise # — 12/20 Ga� Inv� Choke Tube, 9B38P53 � � $ 43.99

— Advise # — Beretta/Benelli Choke Tube, 9B38J53 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 43.99

Minimum gap geometry and high resolution “RMS” interior fin-ish gives less pellet deformation; consistently tighter patterns. Choke constriction is laser marked on color coded band, no need to remove tube to verify size. Long tube with hidden wrench slots extends be-yond the length of the muzzle. Knurled grasping band speeds installation and removal. abSPECS: 17-4 stainless steel. Polished bright finish. Extends beyond muzzle approximately .812" (20.6mm). Use with lead and bismuth shot. Steel shot can be used with constrictions of Modified and larger. Available to fit Browning Invector Plus and Beretta/Benelli.

BRILEY

SPECTRUM MACH 1 CHOKE TUBE

Competition Grade Tubes, Extra High Polish Interior Improves Pattern & Accuracy

stk# InVectoR PLus

stk# beRettA/beneLLI

choke gAuge

#129-000-019AQ #129-000-055AQ Skeet 12#129-000-020AQ #129-000-056AQ Imp Cyl 12#129-000-021AQ #129-000-057AQ Lt Mod 12#129-000-022AQ #129-000-058AQ Mod 12#129-000-023AQ #129-000-059AQ Imp Mod 12#129-000-024AQ NA Lt Full 12#129-000-025AQ NA Full 12#129-000-026AQ NA X-Full 12

— Advise # — Spectrum Mach 1 Choke Tube, 9B51D39 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 58.99

QUESTIONS BEFORE YOU BUY?Call Or Email Our

Full-Time Tech Staff

PAGE 203Orders/Tech: 800-741-0015order on the web

brownells.com

ch

ok

e t

ub

es

sho

tg

un

Steel choke tubes fit popular mod-els of shotguns and give tight patterns with 00 and 000 buckshot. Chokes feature ports to help tame the recoil and muzzle jump produced by buckshot loads. Can be used with lead, steel and Hevi-Shot. Not for use with any steel shot larger than BB or faster than 1550 fps. abSPECS: 17-4 heat treated steel. Matte black finish.

CARLSON’S

BUCKSHOT CHOKE TUBESSpecial Choke Tubes Give Tight

Patterns With Buckshot

#155-000-225AQ Rem Choke Buckshot Choke, 5E37K50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 47.95

#155-000-226AQ Beretta/Benelli Mobil Choke Buckshot Choke, 5E37P50� � � � � � � � � � 47.95

#155-000-227AQ Win-Choke Buckshot Choke, 5E37H50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47.95

Parallel section 25% longer than Carlson’s conventional tubes helps produce even more consisten, dense shot patterns. Extra smooth interior surface minimizes shot deformation. Laser marked constriction pro-vides fast identification. External knurled ring extends ap-proximately 3/4" from end of barrel for fast changes between stations. Can be used with lead, steel, copper-plated, and nickel shot, as well as Hevi-Shot and buck shot. Steel shot larger than BB should not be used in tubes with Extra Full constriction. abSPECS: 17-4 stainless steel, natural silver finish. 12 gauge only. Constric-tion (SIZE) listed in tables below. Threads are as follows: Win-Choke® - .812"-32. Also fits Browning Invector, Mossberg 500, Weatherby, and Sav-age. Browning Invector-Plus - .820"-32. Beretta - .810"- 1mm. Also fits Benelli M1 and Super 90. Rem™ Choke - .812"-32. Crio-Plus fit Benelli® Criotech® M2 and Super Black Eagle II.

CARLSON’S

SPORTING CLAYS TUBEGives Tight, Consistent

Patterns With Minimal Shot Deformation

12 GAUGE CLAYS TUBES

stk# WIn-choke stk# InV.-PLus choke#155-000-001AQ .730" #155-000-009AQ .740" Cyl#155-000-002AQ .725" #155-000-010AQ .735" Skeet#155-000-003AQ .720" #155-000-011AQ .730" Imp Cyl#155-000-004AQ .715" #155-000-012AQ .725" Lt . Mod#155-000-005AQ .710" #155-000-013AQ .720" Mod#155-000-006AQ .705" #155-000-014AQ .715" Imp Mod#155-000-007AQ .700" #155-000-015AQ .710" Full#155-000-008AQ .690" #155-000-016AQ .700" Extra Full

— Advise # — 12 Gauge Clays Tube, 5E33G08 � � � � � � � $ 38.99

12 GAUGE CLAYS TUBES

stk# beRettA stk# ReM choke choke#155-000-017AQ .725" #155-000-025AQ .730" Cyl#155-000-018AQ .720" #155-000-026AQ .725" Skeet#155-000-019AQ .715" #155-000-027AQ .720" Imp Cyl#155-000-020AQ .710" #155-000-028AQ .715" Lt . Mod#155-000-021AQ .705" #155-000-029AQ .710" Mod#155-000-022AQ .700" #155-000-030AQ .705" Imp Mod#155-000-023AQ .695" #155-000-031AQ .700" Full#155-000-024AQ .685" #155-000-032AQ .690" Extra Full

— Advise # — 12 Gauge Clays Tube, 5E33C08 � � � � � � $ 38.99

CRIO-PLUS TUBES

— Advise # — 12 Ga� Crio-Plus Tube, 5E36H15 � � � � � � � $ 43.99

Crio-Plus

stock # choke sIZe#155-000-068AQ Cyl .725"#155-000-069AQ Skeet .720"#155-000-070AQ Imp Cyl .715"#155-000-071AQ Lt Mod .710"

stock # choke sIZe#155-000-072AQ Mod .705"#155-000-073AQ Imp Mod .700"#155-000-074AQ Full .695"#155-000-075AQ X-Full .690"

Flush mount, stainless steel tubes available for the many shot-guns using the popular Win-Choke thread size and standard Tru-Chokes, plus Remington, Beretta/Benelli, Browning Invector Plus, and Mossberg 835 Ultra Mag. These tubes can be used with magnum and steel shot loads. Tru™-Choke Thinwall tubes are recommended for 23/4" lead shot loads ONLY. All X-Full and Turkey constrictions are for use with lead and Hevi-Shot ONLY! abSPECS: 1704 Stainless steel, heat treated. Available for 12 and 20 gauge, depending on model. Tru-Choke™-style (T-C): .795"-44 tpi fits 12 ga. Tru-Choke-style, .675"-44 tpi fits 20 ga. Tru-Choke-style. Tru-Choke Thinwall-style: .774"-44 tpi fits 12 ga. barrels altered to accept Thinwall chokes and recommended for 23/4" lead shot loads ONLY. Win-Choke®-style: .812"-32 tpi (12 ga.) or .687"-32 (20 ga.) fits barrels originally equipped with Win-Choke®, Browning Invector, Mossberg Accu-Choke®, Weath-erby IMC®, or Savage choke tubes. Rem™Choke-style: .814"-32 tpi (12 ga.) or .702"-32 (20 ga.) fits barrels originally equipped with Rem™Choke factory tubes. Beretta/ Benelli: .810"-1mm fits Beretta and Benelli M1 and Super 90. Invector Plus-style: .820"-32 tpi (12 ga.) fits barrels originally equipped with Browning Invector Plus factory tubes.

stk# beR./ben. 12 gA.

stk# beR./ben. 20 gA.

choke

#155-812-008AQ #155-820-008AQ Cyl

TRU-CHOKE (T-C) & TRU-CHOKE THINWALL

stk# t-c 12 gA.

stk# t-c 20 gA.

stk# thInWALL 12 gA. choke

#155-212-008AQ #155-220-008AQ #155-412-008AQ Cyl#155-212-007AQ #155-220-007AQ #155-412-007AQ Skeet#155-212-006AQ NA #155-412-006AQ Imp Cyl#155-212-004AQ #155-220-004AQ #155-412-004AQ Mod#155-212-003AQ NA #155-412-003AQ Imp Mod#155-212-002AQ #155-220-002AQ #155-412-002AQ Full#155-212-001AQ #155-220-001AQ #155-412-001AQ X-Full#155-212-000AQ #155-220-000AQ NA Turkey

NA #155-220-006AQ NA Imp

— Advise # — Tru-Choke Std & Thinwall Choke Tubes, 5E15J31 � � � � � � � � � � � � � � � � � � � � � � � $ 17.99

WIN-CHOKE & INVECTOR PLUS

stk# WIn. 12 gA.

stk# WIn. 20 gA.

stk# InV. PLus 12 gA. choke

#155-000-090AQ #155-000-052AQ #155-612-008AQ Cyl#155-000-091AQ #155-000-053AQ #155-612-007AQ Skeet#155-000-092AQ #155-000-054AQ #155-612-006AQ Imp Cyl#155-000-093AQ #155-000-055AQ #155-612-004AQ Mod#155-000-094AQ #155-000-056AQ #155-612-003AQ Imp Mod#155-000-095AQ #155-000-057AQ #155-612-002AQ Full#155-000-096AQ #155-000-058AQ #155-612-001AQ X-Full#155-000-097AQ #155-000-059AQ #155-612-000AQ Turkey

— Advise # — Invector Plus Choke Tube, 5E13I23 � � � $ 15.99

REM-CHOKE

stk# ReM. 12 gA.

stk# ReM. 20 gA. choke

#155-712-008AQ #155-720-008AQ Cyl#155-712-007AQ NA Skeet#155-712-006AQ #155-720-006AQ Imp Cyl#155-712-004AQ #155-720-004AQ Mod#155-712-003AQ #155-720-003AQ Imp Mod#155-712-002AQ #155-720-002AQ Full#155-712-001AQ #155-720-001AQ X-Full#155-712-000AQ #155-720-000AQ Turkey

— Advise # — Win- & Rem Choke Tubes, 5E13L23 � � � $ 15.99

BERETTA/BENELLI

CARLSON’S CHOKE TUBENon-Rusting Stainless Steel

stk# beR./ben. 12 gA.

stk# beR./ben. 20 gA.

choke

#155-812-007AQ #155-820-007AQ Skeet#155-812-006AQ #155-820-006AQ Imp Cyl#155-812-004AQ #155-820-004AQ Mod#155-812-003AQ #155-820-003AQ Imp Mod#155-812-002AQ #155-820-002AQ Full#155-812-001AQ #155-820-001AQ X-Full#155-812-000AQ #155-820-000AQ Turkey

— Advise # — Beretta/Benelli Choke Tubes, 5E16B14 � � $ 18.99

Three choke set helps you configure your shotgun to match your shooting condi-tions. Stainless steel chokes fea-ture long parallel internal sec-tions that throw tight, consistent patterns to help you bag more birds. Laser marked on end and body for easy identification and knurled for quick installation —just screw in the choke that matches your hunting situation. Close-Range choke is ideal for shooting over decoys out to 30 yards. Mid-Range choke is best for 25 to 40 yard shots. Long-Range choke designed for shots 40 yards and beyond. Chokes accept steel shot up to size BB, at velocities less than 1550 fps. Padded hard case fits into your pocket and keeps chokes handy in the field. Available in 12 gauge only, for several different shot-gun makes and models. abSPECS: 1704 stainless steel, matte black finish. Chokes extend ¾" beyond muzzle.

CARLSON’S

WATERFOWL CHOKE TUBE SETHelps Knock Down Ducks &

Geese At Any Range

stock # FIts PRIce#155-000-203AQ Most Beretta & Benelli 5E89F26 $ 104.99#155-000-204AQ Most Remington 5E89Q26 $ 104.99#155-000-205AQ Browning Invector Plus 5E89J26 $ 104.99#155-000-206AQ Browning Invector, Moss-

berg 500, Savage, Weatherby, Winchester

5E86L07 $ 89.99

High quality, inter-changeable tubes not only improve pattern density but vent exiting barrel gases to reduce felt recoil and muzzle lift. Helps keep the barrel down and the front bead on target for a faster follow-up shot. Knurled end makes installation/removal easy. Use only with lead shot; 12 ga. only. abSPECS: E.D.T. steel, blue, matte finish. 31/2" (8.8cm) long. For use with lead shot only. 12 ga. only. Available to fit Tru-Choke™ Style Tru-Tube - .795"-44 tpi., Rem™ Choke - .812"-32 tpi., Invector - .812" 32 tpi.

COLONIAL ARMS

“ELITE” PORTED CHOKE TUBEReduces Recoil &

Shoulder Pain; Improves Pattern Density

stk# tRu-tube stk# ReM choke choke#198-050-004AQ #198-053-004AQ Mod#198-050-006AQ #198-053-006AQ Full

NA #198-053-003AQ Imp CylNA #198-053-005AQ Imp Mod

— Advise # — Elite Ported Choke Tube, 8A34I54 � � � � $ 40.99

Beautifully made tubes with an ex-tremely smooth inside finish and an un-dercut, tube-to-barrel joint to minimize shot and wad fouling buildup. Both Win-Choke® and Tru-Choke™ tubes are “invis-ible” style, no unsightly “knob” sticks out. And, they can’t rust; they are stainless steel. Install/remove with a quarter. For use with lead shot only! abSPECS: Approximately 11/2" (3.8cm) long. Stainless steel. Threads are as follows - Win-Choke® 12 ga. are .812"-32 tpi, 20 ga. are .687"-32 tpi; Tru-Tube 12 ga. are .795"-44, 20 ga. are .675"-44; Tru-Choke™-style Thinwall are .774"-44.

stk# tRu-tube stk# thInWALL gAuge choke#198-112-730AQ #198-212-730AQ 12 Skt-1#198-112-725AQ #198-212-725AQ 12 Imp Cyl#198-112-715AQ #198-212-715AQ 12 Mod#198-112-705AQ #198-212-705AQ 12 Full#198-112-700AQ #198-212-700AQ 12 X-Full#198-120-620AQ NA 20 Imp Cyl#198-120-610AQ NA 20 Mod#198-120-600AQ NA 20 Full

NA #198-212-710AQ 12 Imp Mod

— Advise # — 12/20 Ga� Tru-Tube, 8A13H50 � � � � � � � � � $ 15.99— Advise # — 12 Ga� Thinwall, 8A15L79 � � � � � � � � � � � � � 18.99

COLONIAL ARMS

SCREW-IN CHOKE TUBE“Invisible” Replacement Tubes For Popular Screw-In Choke Systems

stock # gA. choke PRIce#198-012-730AQ 12 Skt-1 8A12G91 $ 15.99#198-012-725AQ 12 Imp Cyl 8A12B91 $ 15.99#198-012-715AQ 12 Mod 8A12B91 $ 15.99#198-012-705AQ 12 Full 8A12I91 $ 15.99#198-012-700AQ 12 X-Full 8A12K91 $ 15.99#198-020-595AQ 20 Mod 8A12P91 $ 15.99#198-020-585AQ 20 Full 8A12K91 $ 15.99

Precision machined from 17-4 stainless steel, these choke tubes feature a 25% larger parallel section than conventional tubes, resulting in tighter, denser, and more con-sistent patterns. Choke size is laser

etched on each tube for easy identification, and the knurled end makes removal quick and easy. Lead, copperplated, nickel Hevi-Shot™, bismuth, tungsten, or steel shot may be used in these choke tubes. Do not use steel shot larger than BB in any Sporting Clays Choke Tube tighter than full constriction. abSPECS: 17-4 stainless steel, polished.

CARLSON’S BROWNING INVECTOR DS CHOKE TUBEPatterns Better Than Standard Choke Tubes

stock # choke DIA.#155-000-228AQ Cylinder .740#155-000-229AQ Skeet .735#155-000-230AQ Improved Cylinder .730#155-000-231AQ Light Modified .725#155-000-232AQ Modified .720#155-000-233AQ Improved Modified .715#155-000-234AQ Full .710#155-000-235AQ Extra Full .700#155-000-236AQ Turkey .665

— Advise # — Invector DS Choke Tube, 5E33G57 � � $ 39.99

PAGE 204 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

Pe

RFo

RM

An

ce

PA

Rt

sc

ho

ke

tu

be

ssh

ot

gu

n

Super full constriction gives dense patterns for precise shot

placement. Multiple ports reduce muzzle rise and recoil. Hard-ened stainless steel adds strength and wearability. Knurled for fast, easy removal. cAutIon: Turkey constrictions are FoR LeAD or hevi-shot onLY! abSPECS: 1704 stainless steel, hardened. Matte black finish. 23/8" (6cm) long. REM fits 12 ga. Remington .812-32 threads only. Inv. Plus fits Browning Invector Plus, WBMW fits Winchester, Browning Invector, Mossberg 500, Weatherby Beretta fits Beretta/Benelli, Moss. 835 fits Mossberg 835.

eXtenDeD tuRkeY tubes - 17-4, heat-treated, stainless steel tur-key tubes stand up to the heaviest loads and deliver tight, consistent patterns with less fliers. Knurled on the end for quick installation and removal. 12 gauge tubes ex-tend approximately 1" from the end of the barrel, and 20 gauge tubes extend approximately 3/4" from the end of the barrel. For use with lead, copperplated, nickel, Hevi-Shot, buffered lead, and bismuth shot. not FoR use WIth steeL shot.SPECS: 17-4, heat-treated stainless steel, matte blue. NOT FOR USE WITH STEEL SHOT

stock # constRIctIon FIts gAuge#155-000-076AQ .575 Win-Choke® 20#155-000-077AQ .575 Rem™-Choke 20#155-000-080AQ .640 Rem™-Choke 12#155-000-081AQ .660 Rem™-Choke 12#155-000-082AQ .640 Win-Choke® 12#155-000-083AQ .660 Win-Choke® 12#155-000-078AQ .575 Beretta/Benelli 20#155-000-079AQ .585 Browning Invector Plus 12#155-000-084AQ .640 Beretta/Benelli 12#155-000-085AQ .650 Beretta/Benelli 12#155-000-086AQ .655 Browning Invector Plus 12#155-000-087AQ .665 Browning Invector Plus 12

— Advise # — Extended Turkey Tube, 5E24P54 � � � � � � $ 29.99

#155-000-089AQ Benelli Cro-Plus, 12 Ga. .665", 5E36C15 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 43.99

CARLSON’S PORTED TURKEY TUBETight Patterns, Reduced Recoil

stock # FIts choke DIA. PRIce#155-000-035AQ Rem . .665" 5E35E31 $ 41.99#155-000-036AQ Inv . Plus .665" 5E35J31 $ 41.99#155-000-037AQ WBMW .660" 5E35K31 $ 41.99#155-000-038AQ Beretta .665" 5E35I31 $ 41.99#155-000-039AQ Moss . 835 .675" 5E35L31 $ 41.99

External “Special Purpose” Choke Tubes made from high tensile strength e.d.t. 150 carbon steel to withstand the higher pres-sures created by large shot and the constant pounding of competitive

shooting without bulging at the threads or splitting the barrel. If a tube does fail, simply remove and replace with another. abSPECS: Blued e.d.t. 150 carbon steel choke tubes, Hardened to Rc 32. Approx. 23/4" (6.98cm) long. Dimension shown in price line is nominal I.D. Tru-Choke™ (TC) 12 ga. .795"-44 tpi. 20 ga. .675"-44 tpi. Tru-Choke™ Thinwall (TW) 12 ga. .774"-44 tpi. Rem™Choke (RC) 12 ga. .812"-32 tpi. Win-Choke® (WC) .812"-32 tpi.

tuRkeY tube - Deliver extra tight patterns when used with heavier charges of large size lead shot. Not for use with steel shot!#198-025-109AQ 12 Ga� TC, .680" full, 8A18K20 � � � � � � � $ 21.99#198-025-110AQ 12 Ga� TC, .675" X-full, 8A18G20 � � � � � 21.99#198-025-309AQ 12 Ga� RC, .680" full, 8A18J20 � � � � � � � 21.99#198-025-009AQ 12 Ga� WC, .680" full, 8A18I20 � � � � � � � 21.99#198-024-410AQ 20 Ga� TC, .570" X-full, 8A18P20 � � � � � 21.99

cARD shootIng tube - Tru-Choke™, Rem™Choke and Win-Choke®-style tubes with very tight constriction for tightest pat-terns with #10 lead shot. Not for use with shot sizes larger than #8 lead. Not for use with steel shot!#198-026-302AQ 12 Ga� RC, .654" #2 Card, 8A18I20 � � � $ 21.99#198-026-002AQ 12 Ga� WC, .654" #2 Card, 8A18L20 � � 21.99

gunsMIth bLAnk tube - Undersized I.D., open up to match customer’s needs. Must not be used as sold. Must be opened up. Gun damage or shooter injury may occur if constriction is too tight for the shot size and type being used!#198-027-044AQ 12 Ga� TC, .635" Blank, 8A18N20 � � � � $ 21.99#198-027-244AQ 12 Ga� TW, .635" Blank, 8A18H20 � � � � 21.99#198-027-332AQ 12 Ga� RC, .635" Blank, 8A18P20 � � � � � 21.99#198-027-032AQ 12 Ga� WC, .635" Blank, 8A18A20 � � � � 21.99

COLONIAL ARMS

“SPECIAL PURPOSE” CHOKE TUBEUnique Designs For Competition Use

Reduced diameter, extended knurled ring gives the neces-sary clearance to let you use two choke tubes in side-by-side and over/under guns. Extended tube places the choke restric-tion outside the barrel. Prevents steel shot battering from jam-ming tube into the barrel. Knurled ring for easy removal with-out a wrench. Not for use with “F” or “T” size shot! abSPECS: Steel, blue finish. 23/8" (6cm) long. Tru-Tube fits EAA Baikal and other guns. 12 ga. only, .795"-44 tpi.

COLONIAL ARMS

DOUBLE GUN TUBESteel Shot Tubes; Slim Profile Fits

EAA Baikal Doubles & Over/Unders

#198-000-001AQ 12 Ga� Imp Cyl Choke, 8A18Q20 � � � � $ 21.99#198-000-002AQ 12 Ga� Modified Choke, 8A18A20 � � � 21.99#198-000-003AQ 12 Ga� Full Choke, 8A18E20 � � � � � � � � � 21.99#198-000-004AQ 12 Ga� X-Full Choke, 8A18E20 � � � � � � 21.99

Steel shot will bulge even the toughest, thickest shotgun barrel at the choke ruining both barrel and choke tube. Colonial solves

the problem by locating the choke beyond the barrel and threads. A Super Steel tube will expand, but all that’s damaged is the tube, not your barrel. Just unscrew the tube and replace. abSPECS: Blued steel. Approx. 25/8" (6.7cm) long. 12 ga. only. Threads as follows: Win-Choke® Invisible - .812"-32 tpi. Tru Choke™-style Tru-Tube - .795"-44. Tru-Choke™-style Thinwall are .774"-44.

COLONIAL ARMS

SUPER STEEL SCREW-IN CHOKE TUBE FOR STEEL SHOT

Tough, Blued Steel Designed To Take Steel Shot Abuse

stk# WIn-choke stk# tRu-tube stk# thInWALL choke#198-712-725AQ #198-512-730AQ #198-412-725AQ Imp Cyl#198-712-715AQ #198-512-720AQ #198-412-715AQ Mod#198-712-705AQ #198-512-710AQ #198-412-705AQ Full

NA #198-512-705AQ #198-412-700AQ X-Full

— Advise # — Super Steel Tube, 8A18L20 � � � � � � � � � � � � $ 21.99

Machined steel, extend-ed tactical choke with large diameter bore provides extra wide patterns at close range for home defense or CQB operations. Features a serrated, saw-tooth tip that holds tight against locks and hinges to prevent the muzzle from sliding during forced entry operation. Twelve, equally spaced ports redirect com-bustion gases to reduce felt recoil and prevent barrel damage when used for forced entry. Knurled gripping surface makes it easy to install and remove the choke without special tools. Precision machined from 1704 stainless steel for maximum strength, then treated with a manganese phosphate finish for improved wear resistance. Models available for Mossberg 835/935, Winchester/ Savage/Browning Invector/Weatherby/Mossberg 500, Remington, and Beretta/Benelli shotguns,12 gauge only. Can be used with lead, buckshot, hevishot, or steel shot without damage. abSPECS: 1704 stainless steel, manganese phosphate finish, matte black. Fits 12 gauge only.

CARLSON’S

TACTICAL BREECHER CHOKEProvides An Extra Wide

Shot Pattern; Serrated Tip Aids In Door Breeching

stock # FIts PRIce#155-000-098AQ Mossberg 835/935 5E40J00 $ 49.99#155-000-099AQ Winchester/Savage Browning

Invector/Wthrby Mossberg 5005E40J00 $ 49.99

#155-000-100AQ Remington 5E40C00 $ 49.99#155-000-101AQ Beretta/Benelli 5E40M00 $ 49.99

Genuine Remington seamless choke tubes made of heat-treated steel alloy for uncompromised strength. Fits Remington shotguns threaded for Rem™ Choke only. In-visible Flush Fit models do not pro-trude from the barrel. turkey tubes extend beyond the end of the barrel to allow a long, gentle constriction. Turkey chokes are designed for fac-tory overbored barrels only and are for lead shot only!*

SPECS: Fits REM™ Choke, .812"-32 tpi threads. Flush Fit - 17-4 stainless steel, polished, flush fitting. 20-gauge Full and Modified tubes can be used with steel and lead shot. Turkey - Carbon steel, blued, extends beyond muzzle. Wrenches - Carbon steel, blued. 4-notch type.

RIFLeD sLug tube - Quickly convert your REM™ Choke equipped shotgun into a deer gun. Fully-rifled tubes spin the slug for better stability and increased accuracy.SPECS: Stainless steel. Flush fit, 12 ga. only. .812"-32 tpi. Fits guns threaded for Rem™ Choke tubes only.#767-000-237AQ Slug Tube, 8F43C39 � � � � � � � � � � � � � � � � $ 49.99

REM™ CHOKE

FACTORY CHOKE TUBEOriginal Equipment Tubes

#767-000-238AQ Full Tube, 20 Ga�, 8F14D21 � � � � � � � � � � $ 16.99#767-000-236AQ *X-Full Turkey Tube, 8F22H44 � � � � � 25.99#767-000-234AQ *Super-Full Turkey Tube,

8F23A47 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 26.99#767-000-195AQ 12 Ga� Wrench, 8F7H75 � � � � � � � � � � � � � 9.99#767-000-196AQ 20 Ga� Wrench, 8F7D75 � � � � � � � � � � � � � 9.99

stk# 12 gA. FLush FIt

stk# 20 gA. FLush FIt

choke

#767-000-231AQ NA Imp Skeet#767-000-229AQ #767-000-240AQ Imp Cyl#767-000-228AQ #767-000-239AQ Mod

NA #767-000-241AQ SkeetNA #767-000-238AQ Full

— Advise # — Flush Fit Tubes, 8F14A21 � � � � � � � � � � � � � � $ 16.99

Multi-purpose, screw-in choke tube gives excellent per-formance with a variety of law en-forcement shotgun ammunition, including rifled slugs, buckshot, and breaching rounds. Direct replacement for popular factory screw-in tubes, so it eliminates the inconvenience of having to change the muzzle device for specific applications. Sharply crenelated muzzle provides the proper stand-off distance and secure grip on the surface for use as a breaching device. Won’t interfere with performance of buckshot, and preserves the downrange accuracy of slugs. Precision machined from car-bon steel, with a knurled surface for easy installation/removal, and a wear-resistant, non-glare black oxide finish. Remington fits Rem™ Choke. Win/Brng/Moss fits WinChoke®, Browning Invector, and Mossberg 500. Benelli/Beretta fits Mobilchoke™ system. ab

TRULOCK CHOKES

TACTICAL CHOKE TUBEDelivers Excellent Performance

From A Variety Of Law Enforcement Ammo

#100-004-579AQ Remington Choke Tube, 2C55F16 � � $ 58.99#100-004-580AQ Win/Brng/Moss Choke Tube,

2C55A16 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 58.99#100-004-578AQ Beretta/Benelli Choke Tube,

2C55N16 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 58.99

SCREW-IN CHOKE INSTALLATION REQUIREMENTS

Before accepting a barrel for machining to accept screw-in chokes, you must measure the outside diam-eter (O.D.) to determine if there will be sufficient wall thickness after machining. “Mike” the O.D. of the barrel and the O.D. of the tap for the particular gauge. Subtract the O.D. of the tap from that of the barrel, divide by 2, and this will give the wall thickness after machining, provid-ing the O.D. of the barrel is concentric with the inside diameter (I.D.). A sample calculation appears below.

Barrel O.D. (12 Ga) .850"Tap O.D. (12 Ga) Win-Choke™ – .814" .036" ÷ 2 = . 018" Wall Thickness

We DO NOT recommend installations in barrels where the resultant wall thickness will be less than .015", pro-viding the I.D. of the barrel is concentric with the O.D. If the I.D. is not concentric with the O.D., you will have to make your own decision as to whether the installation will be safe. In addition, you CANNOT install screw-in chokes in barrels whose inside diameters (I.D.) exceed the following dimensions: 10 ga. - .780"; 12 ga. - .735"; 12 ga. Thinwall - .728"; 16 ga. - .666"; 20 ga. - .624". Exceed-ing these dimensions WILL CAUSE DAMAGED CHOKE TUBES and there is a GREAT POSSIBILITY OF CAUSING A BARREL BLOW-OUT! Check EVERY installation before firing to make sure the tube does not protrude into the bore. Back-bored or jug-choked barrels are usually NOT suitable for screw-in choke installation.

This USA-made, S7 tool steel hammer replaces the factory part and counts as an additional part for 922(c) compli-ance. Drops in without any alterations to the gun and performs exactly like the original. abSPECS: S7 tool steel, black oxide finish.

GEISSELE AUTOMATICS BENELLI M4

HAMMERAmerican-Made, Drop-in

Replacement

#100-008-201AQ M4 HAMMER, 7B59B99 � � � � � � � � � � � � $ 59.99

PAGE 205Orders/Tech: 800-741-0015order on the web

brownells.com

sho

tg

un

Oversized replacement for fac-tory cocking handle is shaped for comfort and fast, easy operation to help you bring your Beretta or Benelli 12-gauge semi-auto shot-gun into action quickly. Precision machined from high-grade alu-minum or stainless steel billet for

strength, durability, and corrosion resistance. Durable black finish matches your gun’s bluing. SPECS: Fit 12 ga. only. Benelli – Stainless steel, matte black finish. Beretta – Aluminum, anodized, semi-gloss black. Fit 390/391 shotguns.

BALLISTIC SPECIALTIES BENELLI/BERETTA

EXTENDED COCKING HANDLESEasy, Fast Operation Of Bolt

Without Abrading HandBeretta

#100-003-683AQ Benelli Handle, 8K24I66 � � � � � � � � � � � � $ 29.99#100-003-688AQ Beretta Handle, 8K28L73 � � � � � � � � � � � 35.99

Benelli

Extra long, easy-to-grasp bolt handle allows fast, positive cycling during tactical operations. Contoured, hour-glass shape provides increased leverage when clearing the action. No modification required, drop-in fit. Models for Benelli SBE/M3, Beretta 303/390/391, Browning Gold, and Remington 1100/11-87. Fits 12 gauge only. abSPECS: Stainless steel, black, oxide finish. Handle - .96" (24mm) long x .5" (12.7mm) diameter.

BRILEY TACTICAL SHOTGUN

BOLT HANDLEFor Fast, Easy Bolt Cycling

#129-000-257AQ Benelli SBE/M3 Bolt Handle, 9B34C24 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 38.99

#129-000-258AQ Beretta 303/390/391 Bolt Handle, 9B34A24 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38.99

#129-000-259AQ Browning Gold Bolt Handle, 9B34A24 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38.99

#129-000-260AQ Rem� 1100/11-87 Bolt Handle, 9B38Q53 � � � � � � � � � � � � � � � � � � � � � � � � � � � 42.99

Increased size allows you to reach over the receiver and operate the bolt with your “off” hand without taking your finger out of shooting position. Provides extra leverage to help clear a jammed chamber. Re-verse contour and open center design gives better grip with gloved hands. Requires no alteration to gun. abSPECS: 4140 Steel, blued finish. Handle is 1.25" (3.1cm) high, 7/8" (22mm) wide. Fits Remington 1100, 11-87 only.

CHOATE COMBAT BOLT HANDLEExtra Wide, Extra Long

Handle Gives Positive Charging For The Remington 1100

#159-101-112AQ Combat Bolt Handle, 9E9M09 � � � � � � $ 11.00

ab

#260-100-101AQ Large Bolt Handle, 6B28H57 � � � � � � � $ 32.99

oVeRsIZe sAFetY button - Easily dis-engages with firing hand trigger finger. Reversible for right- or left-hand use. Fits Benelli Super 90, 121M1 and Beretta 1200 shotguns, no modification to gun.SPECS: 4140 steel, black oxide finish. Head: .440" (11.1mm) dia-meter. .185" (4.7mm) high.#260-100-100AQ Oversize Safety Button, 6B28E57 � � � $ 32.99

LARge boLt hAnDLe - Quick-to-grasp for competition. Fits Benelli Super 90 and Beretta 1200 series, no alterations to gun.SPECS: 4140 steel, black oxide finish. Extends .900" (23mm). .68" (17.4mm) diameter.

DAVE’S METAL WORKS BENELLI/BERETTA

ACCESSORIES

Ideal for law enforcement and competition. Large, extend-ed knob provides a quick-to-grasp handle for rapid operation. Contoured shape gives added leverage for very fast cycling and clearing the action. No modification required, drop-in fit for Remington 1100 and 11-87. abSPECS: 4140 steel, black oxide, matte finish. Knob: 3/4" (19mm) long, 5/8" (15.9mm) diameter.

DAVE’S METAL WORKS REMINGTON 1100/11-87

TACTICAL BOLT HANDLE

#260-000-001AQ Remington Bolt Handle, 6B28Q57 $ 32.99

Quicker Chambering, Easier Bolt Racking

Oversized, easy to feel bolt re-lease button allows quick access

during high stress situations when you need it most. Fea-tures a serrated face almost 11/4" long for a non-slip grip, with or without gloves. Constructed of 4140 ordnance steel with a black manganese phosphate finish for durability. Fits Benelli M1 Super 90, M3 Super 90, and Model 121 law enforcement shotguns. abSPECS: Steel, black, matte finish. Button – 11/4" (3.2cm) long x 5/8" (1.6cm) high.1 oz. (28.4g) weight.

GG&G BENELLI BOLT RELEASE BUTTONOversized For Quick Operation

#336-000-006AQ Bolt Release Button, 6C98L36 � � � � � $ 109.99

Easy to install, oversized charging handle helps you clear misfeeds and

eject a chambered round quickly and efficiently. Machined steel construction, with a distinctive tubular shape, and deep, corkscrew-pattern flutes give an excellent purchase and stylish look. No gunsmithing required. abSPECS: Steel, matte black finish. Benelli/Beretta fits Benelli M1/M2 and Beretta Extrema. Rem. fits Remington 1100 and 11-87. Win./FN fits Win-chester SX2, SX3, and FNH SLP.

NORDIC COMPONENTS

SHOTGUN SPEED BOLT HANDLEOversized, With Fluted Surface For

Fast Charging & Jam Clearance

#100-005-452AQ Speed Bolt Handle, Benelli/Beretta, 1B19G20 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 24.99

#100-005-453AQ Speed Bolt Handle, Rem. 1100/11-87, 1B23F05 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29.95

#100-005-454AQ Speed Bolt Handle, Win./FN, 1B23B05 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29.95

Stamped steel tab quickly installs without gunsmithing onto Benelli M1, M2 and Super Black Eagle shotguns to give large surface area for bolt release. Makes it easy to quickly ac-tiviate the bolt release while wearing gloves, or without looking at the release, important in action shooting sports. Fits under forend and retained by friction. Available in stainless or matte stainless finish. ab

Simple-To-Install Tab Speeds Bolt Release

#100-013-938AQ Benelli Rapid Bolt Release, Stainless, 6C16Q00 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 18.99

#100-013-939AQ Benelli Rapid Bolt Release, Matte Stainless, 6C17A00 � � � � � � � � � � � � � � � � � 20.99

RED NECK TACTICAL BENELLI M1/M2/SBE

RAPID BOLT RELEASE

Streamlined, stainless steel cock-ing handle features unique knurling and front serrations for a sure grip under all conditions. Perfect for 3-Gun or tactical operations. abSPECS: Stainless steel, Ion Bond coating, silver finish. 2.2" overall length, 1" handle length. #100-012-546AQ Ultimate Charging Handle,

7Z34I29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99

TARAN TACTICAL INNOVATIONS BENELLI M1/M2

ULTIMATE CHARGING HANDLEIdeal For Tactical & 3-Gun Use

Drop-in replacement for plas-tic factory button offers rugged, all-steel construction and a raised, crisply grooved ridge to give your thumb extra purchase for fast, “can’t miss” operation on the first try. Steps in the body are cut deeper than original part for additional grab even with wet hands or when wearing gloves. Reversible design allows shoot-ers with small-to medium-size hands to position the thumb ridge farther back to help them operate the safety without hav-ing to break their grip; shooters with large hands can place the ridge forward to give them more room. Precision machined from 4140 steel, heat-treated for extra hardness and wear resis-tance, with a durable, matte, black oxide finish. abSPECS: 4140 steel, oxide finish, matte black. Fits Mossberg 500/590/835 shotguns.

sAFetY kIt - Includes the Brownells Enhanced Safety Button and the other parts in the safety system that get worn, dinged up, or lost. Replace everything at the same time to ensure smooth, positive, reliable operation of this critical component. Safety but-ton screw also sold separately, so you don’t have to buy a whole new kit if the screw gets damaged during installation.SPECS: Kit includes enhanced safety button, button screw, detent plate, detent ball, detent spring, and installation instructions. Fits Mossberg 500/590/835 shotguns.#080-000-564AQ Moss� 500 Enhanced Safety Kit,

8K33B65 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 39.99#631-000-014AQ Safety Button Screw, 1C4F33 � � � � � � � 5.99

MOSSBERG 500/590/835

ENHANCED SAFETY BUTTONShaped For Easy,

No-Slip Operation; Made From Hardened Steel To Last

#080-000-539AQ Moss� 500 Safety Button, 8K15P61 � � $ 19.99

Machined aluminum, drop-in re-placement for the factory plastic safety

is stronger, wider, taller, and easier to activate under stress, with gloves or wet/cold hands. Deep-stepped ridges on the top of the button ensure a secure purchase to operate the safety even if your whole thumb isn’t making contact. Large contact sur-face lets you operate the safety while keeping the trigger finger in the ready-to-fire position. Can be installed in the “wings up” position on guns with traditional stocks, or for shooters with large hands. Install with the “wings down” for shooters with small hands or on guns with pistol grip stocks. All installation hardware included.SPECS: Machined billet 7075 T6 aluminum, hardcoat anodized, matte black. Steel wear plate and screw, black. 15/16" (3.3cm) long, 7/8" (22mm) wide, 5/16" (7.8mm) high at center. Fits Mossberg 500/590 pump-action and 930/935 semi-auto shotguns.

ELITE TACTICAL MOSSBERG 500/590/930/935

TACTICAL SAFETYOversized, Deeply Ridged For Fast,

Reliable Operation Under Stress

#100-005-838AQ Tactical Safety, 1C19B23 � � � � � � � � � � � � $ 24.99

Jumbo size head with undercut grooves is drop-in replace-ment for the small factory button. Makes it easier to find and operate, even with gloves on. abSPECS: 4140 steel, hardened and blued, right-hand only. Fits Rem- ington: 7600, 7400, 6, 4, 48, 58, 552, 572, 740, 742, 760, 870, 1100, 11-48, 11-87, SPT-10, 12, 74, 76, with or without ISS safety.

SCATTERGUN TECHNOLOGIES

TACTICAL RESPONSE® JUMBO HEAD SAFETY

Easy-To-Find, Oversized Button For Remington

#800-100-002AQ Jumbo Head Safety, 8Z15P15 � � � � � � $ 18.99

Solid steel safety with oversized head was originally designed for 3-gun and tactical gun shooters for fast and positive operation, even when wearing gloves. Also great for hunting, home defense, and any other situation where seconds count. abSPECS: Stainless steel, black finish. Fits Benelli M1, M2, M3, M4, Super Black Eagle, Montefeltro, and Remington® Versa Max®.

TARAN TACTICAL INNOVATIONS BENELLI SHOTGUN

OVERSIZED SAFETY BUTTONDesigned For Faster Operation

#100-012-548AQ Benelli Oversized Safety, 7Z25I49 � � $ 27.99

Large, dome-shaped button is quick to locate. Just a quick push with the side of your trigger finger will disengage the safety. Round profile does not snag clothing or guncase liner. Drop-in installation, right-hand use only. abSPECS: Steel, blue, polished finish. .960" (24.4mm) long. Head - .350" tall (8.9mm .433" (11mm) diameter.

VANG COMP SYSTEMS REM 870/1100/11-87

BIG SPEED SAFETYEasy-To-Locate, Quick-To-Disengage

#100-000-569AQ Big Speed Safety, 6K8J99 � � � � � � � � � � $ 11.99

Oversized, aluminum safety is larg-er than the factory part in every dimen-sion to give your thumb more surface

area for engagement. Taller height, wide back end and more pronounced steps give you more pushing leverage. abSPECS: Aluminum, black, anodized. Approximately 13/4" (4.4cm) long, 31/64" (12.3mm) wide, 17/64" (6.7mm) high.

VANG COMP SYSTEMS MOSSBERG 500//590

OVERSIZED SAFETYProvides Easier Safety Engagement

#100-001-364AQ Mossberg Oversized Safety, 6K24C95 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

Pe

RFo

RM

An

ce

PA

Rt

s

PAGE 206 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

sho

tg

un

Re

PL

Ac

eM

en

t P

AR

ts

Pe

RFo

RM

An

ce

PA

Rt

s

Plastic, oversized bar gives you a large area to hit for fast release of the carrier in Benelli semi-auto shotguns. Speeds up the reloading process. Bar mounts to existing release button and requires drilling and tapping button. abSPECS: Plastic, black. 17/8" (47.5mm) long, 9/16" (14.2mm) wide, 1/4" (6.3mm) high. Screw included. Gunsmith installation recommended.

ARRENDONDO BENELLI

CARRIER RELEASE BAROversized For Quick Release

#069-000-015AQ Carrier Release Bar, Benelli, 9F18G04 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 21.99

Extra long, easy-to-reach bolt release lever replaces the original factory button for fast, painless re-loading during combat or competition. Made of aluminum, then is hardcoat anodized for durability; includes a diamond pattern, textured face for a non-slip grip. High strength, steel cartridge latch is titanium nitride coated for superior wear re-sistance. Fits Beretta 301/302/303/390/391/3901/A400 Xplor/Xtrema/Xtrema2, 12 and 20 gauge shotguns. abSPECS: Lever - Aluminum, black, anodized finish. Cartridge Latch - Steel, gold, titanium nitride finish. Lever - 13/64" (2.6cm) long x 7/16" (1.1cm) wide. .3 oz. (8.5g) weight.

BRILEY BERETTA

EZ BOLT RELEASE LEVERExtra Long For Quick, Easy Access

#129-000-256AQ EZ Bolt Release, 9B55E71 � � � � � � � � � � � $ 62.99

Easy-to-hit lever release has a wide, flat paddle that re-duces the effort needed to close the bolt, allowing for faster reloads while hunting or competi-tion shooting. A real advantage for those wearing gloves or who have difficulty pushing the standard button style bolt closer. Professional gunsmithing may be required for installation. abSPECS: CNC machined 17-4 stainless steel, 1.3” (3.3cm) long, 3” (.76cm) wide.

POWER CUSTOM BERETTA 390/391

COMPETITION BOLT RELEASELarge Paddle Release Allows

For Faster Reloads

#713-000-161AQ Competition Bolt Release, 3A85D76 � � $ 99.99

Oversized bolt release button is the perfect size for competition but still small enough to stay out of the way on a tactical or defensive shot-gun. Easy-to-hit, large pad helps you get the gun back into action quickly when seconds count. Gunsmith installation recommended. Drilling and tapping re-quired. abSPECS: Aircraft-grade aluminum, hard-anodized, matte black finish. 1" (2.54cm) long, 9/16" (1.43cm) wide, 5/32" (.4cm) thick. Requires drilling and tapping for installation.

TARAN TACTICAL INNOVATIONS BENELLI SHOTGUN

OVERSIZED BOLT RELEASEThe Right Size For Defense Or

Competition

#100-012-547AQ Oversized Bolt Release, 7Z17Q15 � � � $ 19.99

Ambidextrous, extended magazine release enables lightning-quick reloads without your shotgun ever leaving your shoulder. Press the release with your trigger finger while keeping your hand wrapped around the pistol grip, and change magazines with your opposite hand—all in one motion. Precision laser-cut from heavy-duty, 16 gauge sheet steel

and powder coated for durability. Drop-in installation using the factory mag release pin and spring. Some guns may require minor fitting, following the included instructions. abSPECS: Steel, powder coated, black finish. 13/8" (3.5cm) wide. Includes mounting hardware.

RAM SUPERIOR FIREARM SOLUTIONS SAIGA 12

EXTENDED MAGAZINE RELEASEFor Fast Reloads In The Ready Position

#100-005-300AQ Saiga 12 Extended Mag Release, 3Z25J71 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

Stainless steel extended carrier drops into Benelli semi-automatic shotguns and provides ex-tended rails on both sides that help perfectly center the shell during the reload. Helps make reloading fast and easy and pro-tects your thumb against cuts and abrasions. Installs quickly and elminates the need to weld together a custom carrier. abSPECS: SAE 304 Stainless steel. Fits Benelli M1/M2/M3/SBE and Rem-ington Versamax.

Eases Loading And Helps Increase Speed For Competition

#100-015-582AQ Benelli Accuguide Extended Carrier, 7Z55M72 � � � � � � � � � � � � � � � � � � � $ 79.99

TARAN TACTICAL INNOVATIONS

BENELLI ACCUGUIDE EXTENDED CARRIER

A genuine Mossberg replace-ment for the factory plastic part made to their specs from tough, durable aluminum. Won’t fail when

you really need it. Drops right in with no modification to the re-ceiver or the detent settings. kit includes the same metal safety button, plus all the other parts of the safety, so you can replace everything at the same time to ensure smooth, positive, reliable operation of this critical part. Safety button screw also available separately, so you don’t have to buy a the entire kit if the screw gets damaged during installation. abSPECS: Button - Aluminum, black. 1.19" (30mm) long, .30" (7.6mm) wide. May require minor fitting. Kit includes safety button, button screw, detent plate, detent ball, detent spring, and instructions.

MOSSBERG MOSSBERG 500

METAL SAFETY BUTTONReplace Factory Plastic With

Genuine Factory Metal Button

#631-000-287AQ Moss� 500 Safety Button, 1C13J63 � � $ 16.99#080-000-563AQ Moss� 500 Factory Metal Safety Kit,

8K29B24 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 35.99#631-000-014AQ Safety Button Screw, 1C4F33 � � � � � � � 5.99

Drop-in kit replaces origi-nal factory sear and spring for a smoother, lighter, fully adjustable trigger pull that helps you shoot more accurately. Comes with three different weight springs to lower the heavy factory trigger pull to a comfortable 2, 3, or 4 lbs., then fine-tune the pull with the adjustment screw using the included hex-head wrench. Springs are color-coded for easy identification. abSPECS: Steel sear. Includes 2 lb. (blue), 3 lb. (white), and 4 lb. (red) springs, plus hex-head wrench. Fits Remington 870, 1100, and 11-87 shotguns, all gauges. Also fits 740, 742, 760, 7400, and 7600 rifles.

TIMNEY TRIGGERS REM 870/1100/11-87

TRIGGER FIXFor A Light, Smooth, Adjustable

Trigger Pull

#883-000-022AQ Rem Trigger Fix, 3H90N73 � � � � � � � � � $ 96.99

Heavy-duty 14 gauge steel triggerguard provides an oversized finger opening for fast access in competition

or when wearing gloves. Fits Saiga 12 shotguns converted to receiver-mounted pistol grips. A captive stud on the front of the triggerguard and two button head screws at the rear attach the guard from inside the receiver for a secure, clean, smooth-looking installation. Gunsmith installation recommended. abSPECS: 14 gauge steel, powder coated, black. 43/8" (11.1cm) overall length, 2" (5cm) long trigger opening. Requires drilling out factory triggerguard rivets. Includes mounting hardware. Fit only Saiga 12 with aftermarket pistol grip directly mounted to the receiver.

RAM SUPERIOR FIREARM SOLUTIONS SAIGA 12

OVERSIZED TRIGGERGUARDFor Fast, Easy Trigger Access

#100-005-299AQ Saiga 12 Oversized Triggerguard, 3Z30E77 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 34.99

Eliminates pin drift in the receiver holes so your trigger housing stays in the same place for every shot. Slotted, truss head screws at each end of pin keeps trigger housing properly aligned and free of wobble. Helps deliver reliable trigger perfor-mance in tactical and competition guns. Remington includes both front and rear, anti-walk trigger pins. abSPECS: Steel, blued finish. Remington - Fits Remington 870/1100/11-87. Mossberg - Fits Mossberg 500/590. Winchester - Fits Winchester 1200/1300/1400. Benelli - Fits Benelli Super 90, Winchester Super X and Browning Gold.

SHOTGUN

ANTI-WALK TRIGGER HOUSING PINPrevents Pin & Housing Movement For

Repeatable Trigger Performance

#078-000-048AQ Remington Anti-Walk Trigger Pins, 8G12P81 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 15.99

#078-000-049AQ Mossberg Anti-Walk Trigger Pin, 8G5E61 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7.99

#078-000-050AQ Winchester Anti-Walk Trigger Pin, 8G5N61 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7.99

#078-000-051AQ Benelli Anti-Walk Trigger Pin, 8G5L61 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7.99

#078-000-057AQ Replacement Screws pair, 8G1P02 � 1.25

Stainless steel recoil spring system solves cycling problems caused by recoil system rust and corrosion; completely imper-vious to salt water, humidity and rain. Precision machined to exacting tolerances; reliably cycles all loads, including mag-num and light target loads. Provides an increase in the cyclic rate that lets you get those second and third shots off fast. Op-erates dry; requires no lubes or oils that can harden and slow down action in cold weather. Installs easily without modifica-tions to gun. abSPECS: Stainless steel. Approx. 91/2" (24cm) long. Benelli SBE/ SBE II fits Benelli SBE, SBE II, M1 Super 90, above s/n 155400, and Montefeltro 12 and 20 ga. Benelli SBE 12 ga. 21 mm fits Benelli SBE12 ga. after s/n 185000 and Super 90 above s/n 470000 with 21 mm threads. Benelli M1 fits M1 Super 90 and Montefeltro before s/n 155400. Beretta AL 390 fits AL390, A390 and N391, 12 and 20 ga. Remington 1100/11-87 fits 12 and 20 ga.

SRM PERFORMANCE SURE CYCLE

Improves Auto Shotgun Reliability & Performance

stock # FIts PRIce#100-000-067AQ Benelli SBE/SBE II 1K142K14 $ 159.99#100-000-912AQ Benelli SBE 12 ga . 21mm 1K137D24 $ 159.99#100-000-068AQ Benelli M1 1K137A24 $ 159.99#100-000-069AQ Beretta AL390, 391 1K137H24 $ 159.99#100-000-071AQ Beretta Pintail 1K137Q24 $ 159.99#100-000-216AQ Remington 1100/11-87 1K59N24 $ 67.99#100-000-075AQ Win Super X2, 12 ga . 1K142P14 $ 157.99

Upgraded replacement for factory piston is machined from hardened 17-4 PH stainless steel bar stock to stand up to

the rigors of high-volume shooting without breakage. Tight dimensional tolerances and polished exterior help ensure smooth, reliable function of this critical part for consistent gas system operation and efficient cycling. Drop-in installation: simply remove the end cap and forearm, slip off the factory gas piston, and slip on the Ballistic Specialties piston in its place before reinstalling the forearm and cap. Separate models for 12 and 20 gauge.SPECS: Stainless steel, natural finish. Fits Beretta 391 shotgun.

BALLISTIC SPECIALTIES BERETTA 391

GAS PISTONDelivers Consistent,

Reliable Gas System Function

#100-003-676AQ Beretta 391 Gas Piston, 12 Gauge, 8K44A95 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 59.95

#100-003-677AQ Beretta 391 Gas Piston, 20 Gauge, 8K44M95 � � � � � � � � � � � � � � � � � � � � � � � � � � � 59.95

Don’t let rusted, broken or badly carboned-up gas pistons and seals keep your 1100 or 11-87

from working its best. Long-lasting, stainless steel and Teflon replacement for factory gas system parts. abSPECS: Teflon barrel seal, stainless steel gas piston and piston seal. Kit contains piston, piston seal and barrel seal.

NU-LINE REMINGTON 1100//11-87

GAS SYSTEM PARTSRestores Function & Reliability

#655-110-003AQ 12 Ga� Gas Piston, 5E7F90 � � � � � � � � � � $ 9.95#655-110-002AQ 12 Ga� Piston Seal, 5E8P02� � � � � � � � � � 9.99#655-110-000AQ 12 Ga� Gas System Kit, 5E15Q99 � � � � 19.99#655-110-001AQ 12 Ga� Barrel Seal, 1-pak, 5E2L00� � � � 2.50#655-110-004AQ 12 Ga� Barrel Seal, 10-pak, 5E14Q95 � 19.95#655-110-005AQ 12 Ga� Barrel Seal, 25-pak, 5E32B00 � 40.00#655-000-002AQ 20 Ga� Barrel Seal, 4-pak, 5E6L50 � � � 8.50#655-110-007AQ 20 Ga� Barrel Seal, 10-pak, 5E15E00 � 19.95

High-grade silicone rubber O-rings replace old, worn, or cracked rings to pro-

vide a proper seal and restore gas system reliability. Fits a wide variety of 12- and 20-gauge shotguns. 20-gauge rings will fit many 28 gauge shotguns, too. abSPECS: Rubber, black. Fits Remington 1100/11-87, Beretta, Winchester, Franchi, Charles Daly, Tri-Star, EAA, and others. Kit contains (4) 12 gauge rings and (2) 20 gauge rings.

CARLSON’S SEMI-AUTO SHOTGUN

GAS O-RING REPLACEMENT PAKReplace Worn Out O-Rings To Help

Restore Proper Gas System Function

#155-000-102AQ Gas O-Ring Pak, 5E10L00 � � � � � � � � � � $ 12.99

PAGE 207Orders/Tech: 800-741-0015order on the web

brownells.com

Re

PL

Ac

eM

en

t P

AR

ts

sho

tg

un

Thicker-than-factory replacement decreases the amount of play in the latch body to improve feeding and ensure posi-tive operation. Available in three different thicknesses. abSPECS: Steel, black oxide, matte finish. .025" (.64mm), .030"(.76mm), or .035" (.89mm) thick.

REMINGTON 1100/11-87

INTERCEPTOR LATCH RETAINEROversized To Minimize Latch Wobble

#080-000-156AQ �025" Int� Latch Retainer, 8K0D99 � � � $ 1.99#080-000-157AQ �030" Int� Latch Retainer, 8K0I99 � � � � 1.99#080-000-158AQ �035" Int� Latch Retainer, 8K0A99 � � � 1.99#080-000-159AQ 3-Pak Int� Latch Retainer, 8K2B82 � � � 3.99

Don’t get caught short or let a broken shotgun ruin your hunt. Convenient, pre-

packaged kits contain the parts most often required for emer-gency, field repairs. All parts are Remington, Mossberg and Winchester Factory, tagged with the Brownells stock number, and current factory parts number. abSPECS: Kits contain one each of parts listed unless noted.

ReMIngton 11-87 - Firing pin, firing pin spring, firing pin re-taining pin, bolt buffer, right-hand extractor, extractor plunger, extractor spring, operating handle, barrel seal, front and rear trigger plate pins. Fits 12 ga. only.#080-938-000AQ 11-87 Field Repair Kit, 8K73N98 � � � � $ 79.99

ReMIngton 1100 - Firing pin, firing pin spring, firing pin re-taining pin, breech bolt buffer, bolt buffer, extractor, extractor plunger, extractor spring, barrel seal, front and rear trigger de-tent springs, operating handle. Fits 12 ga. only.#080-937-000AQ 1100 Field Repair Kit, 8K78A86 � � � � � $ 84.99

ReMIngton 1100/11-87 PIston/seAL FIeLD seRVIce kIt - Two barrel seals, one piston and one piston seal. Fits all 12 ga., plus large-frame 16/20 ga. guns with X or N in serial number.#080-936-000AQ 1100/11-87 Piston Field Service Kit,

8K29M66 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 32.99

ReMIngton 870 - Firing pin, firing pin spring, firing pin re-taining pin, 12/16/20 gauge extractor, extractor plunger, ex-tractor spring, magazine spring retainer (old style), magazine spring retainer (new style), front and rear trigger detent springs.#080-935-000AQ 870 Field Repair Kit, 8K66L37 � � � � � � $ 74.99

PUMP & SEMI-AUTO SHOTGUN

FIELD REPAIR KITMake Your Field Repairs

With Genuine Factory Parts

These high-quality O-rings are perfect for replacing old, cracked or worn O-rings in your 12 gauge 1100/11-87 Reming-ton. Restores the airtight seal on your semi-auto so the gas sys-tem will function efficiently and reliably. Also works with other shotguns that use an O-Ring barrel seal such as: Pro Bore Guns, G-3 models, Beretta shotguns, Franchi shotguns, Winchester shotguns, Charles Daly shotguns, Tri Star shotguns, EAA shot-guns and many others. Available in packs of 3, 10 and 25. abSPECS: Rubber, graphite-coated O-rings. Fits 12 gauge Remington 1100/11-87 and other shotguns that use an O-ring barrel seal.

REMINGTON 1100/11-87

GAS O-RING PAKS Graphite-Coated For Lasting

Performance

#080-155-003AQ Gas O-Ring, 3-Pak, 8K4H50 � � � � � � � � � $ 5.99#080-155-010AQ Gas O-Ring, 10-Pak, 8K13I50 � � � � � � � � 15.99#080-155-025AQ Gas O-Ring, 25-Pak, 8K28G00 � � � � � � � 34.99

Factory components replace worn out, carboned-up fac-tory gas system components to restore the reliability and per-formance of your shotgun. Includes corrosion-resistant, 300 series stainless steel piston and piston seal, plus Teflon coated barrel seal for durability and long service life. Drop-in, long-lasting replacement parts require no gunsmithing. Installation instructions included. SPECS: Teflon barrel seal, stainless steel gas piston and piston seal. Kit contains piston, piston seal, and barrel seal. Fits 12 gauge Remington 1100/11-87 only.

REMINGTON 1100/11-87

GAS SYSTEM KITReplacement Piston,

Piston Seal & Barrel Seal To Maintain Performance,

Cycling & Reliability

#767-000-930AQ Rem 1100/11-87 Gas System Kit , 7F23A63 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 27.99

Remington factory gas system seals keep 1100s and 11-87s functioning their best. Available for 12 and 20 gauge models in a single pak and money-saving six and twelve paks. abSPECS: Teflon seal.

REMINGTON 1100//11-87

BARREL SEALSImprove Reliability & Function

#767-158-990AQ 12 Gauge Bbl Seal, 1-pak, 7F5K65 � � � � $ 6.99#078-000-014AQ 12 Gauge Bbl Seal, 6-pak, 8G33J00 � � 39.99#078-000-015AQ 12 Gauge Bbl Seal, 12-pak, 8G64L27 � 76.99#767-144-370AQ 20 Gauge Bbl Seal, 1-pak, 7F5N90 � � � � 6.99#078-000-016AQ 20 Gauge Bbl Seal, 6-pak, 8G33H56 � � 37.99#078-000-017AQ 20 Gauge Bbl Seal, 12-pak, 8G64K88 � 76.99

Steel piston and piston seal re-places worn parts for proper func-tioning and reliability. Drop-in, long-lasting factory replacement part requires no gunsmithing and comes with factory installation instructions. abSPECS: Steel. Installation instructions included.

REMINGTON 1100//11-87

PISTON & PISTON SEAL ASSEMBLYFactory Replacement Part Keeps

Your Semi-Auto Functioning

#767-200-295AQ Piston/Piston Seal Assembly, 7F17C98 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 20.99

Ready for installation by gunsmith. Precision workman-ship. Duplicates original. Saves waiting for, or having to make, one. abSPECS: Heat treated steel, blued. Fits Winchester Model 12 chambered in 12 gauge only. Gunsmith fitting may be required.

GLEND ARMS WINCHESTER MODEL 12

FIRING PINPrecision-Made -

Duplicates Original

#350-100-102AQ Win� Mod� 12 Firing Pin, 5C19N99 � � $ 19.99

Precision machined from stainless steel and heat treated for long life. Much improved over the factory. abSPECS: Stainless steel. Rc 45-50. In-cludes upper and lower pin and 2

springs. 12 and 20 ga. Will fit Classic Doubles.

NU-LINE WINCHESTER 101

FIRING PIN SETBetter-Than-Factory

#655-101-000AQ 12 Gauge 101 FP Set, 5E33L90 � � � � � � $ 41.85#655-101-100AQ 20 Gauge 101 FP Set, 5E38A62 � � � � � � 46.50

Takes care of most single and double barrel firing pin replace-ments. abSPECS: Kit contains 25 firing pins; 5 each of 5 styles, plus 5 rebound springs.

WILLIAMS FIRING PIN KITDoes Many Singles & Doubles

#962-500-000AQ Firing Pin Kit, 2F66L43 � � � � � � � � � � � � � $ 74.99#962-500-001AQ Style 1 Firing Pin, each, 2F4J56 � � � � 5.99#084-000-165AQ Rebound Sprngs, 3-pak, 4H8C19 � � � 10.99

STYLE FITS1 Stev. 94B-C, 107B-C, 94BT, 107BT;Sav./Stev Sgls.2 Obsolete Stevens Single Barrel3 Iver Johnson Champion/Western Field Sgls.4 Fox “B” Stevens 515, 315, 530, 530A, 311,

311A, 311T, 530A5 H&R 48; Sears/Wards Singles made by H&R

Direct replacement for the original factory part on late-model tactical Mossberg pump shotguns and older 500-series sporting shotguns with two ac-tion bars. Comes fully assembled with 73/4" slide tube, rail unit, and tube nut installed. Make sure you measure the length of your current slide tube to ensure proper fit. It should be 73/4" long with the tube nut removed; measure from the start of the threads to the end of the tube.SPECS: Steel, blued, matte finish. Fits Mossberg 500/590 pump shotguns with two action bars; 12 gauge only.

Replacement For Factory Part On 12 Gauge 500/590

#687-000-049AQ Mossberg 500/590 Action Slide Assembly, 7H44L60 � � � � � � � � � � � � � � � � $ 49.99

PRO MAG MOSSBERG 500//590

ACTION SLIDE TUBE ASSEMBLY

Smoothbore 181/2" barrels quickly convert a Remington 870 or Benelli Nova/SuperNova into a fast-handling slug gun or home defense shotgun. Features chrome-lined bore and Carl-son cylinder-bore choke tube installed. Remington 870 barrels are threaded for standard Rem Choke and have 3" chambers. benelli barrels have 31/2" chambers and are threaded for Benelli Mobil choke. Both are available with a choice of ramped blade front sight only or adjustable front/rear rifle sights.SPECS: 4140 steel, bead-blasted, matte black finish. Chrome-lined bore. 181/2 (47cm) long. 3 lbs (1.3kg) wt.

CARLSON’S

REPLACEMENT SHOTGUN BARRELS

Converts Sporting Pump Shotgun Into A Slug Gun

stock # sIghts FIts PRIce#155-000-199AQ Front Blade Remington 870 5E138K19 $ 151.50#155-000-200AQ Rifle F/R Remington 870 5E172P50 $ 184.30#155-000-201AQ Front Blade Benelli Nova/

SuperNova5E179F30 $ 188.50

#155-000-202AQ Rifle F/R Benelli Nova/SuperNova

5E209N65 $ 220.50

High quality vent rib replacement barrels for Remington 870 and Benelli Nova shotguns. Barrels are made from certi-fied ordinance grade 4140 steel, with chrome lined bores and a satin matte blue finish. Red fluorescent front sight includes a brass center bead. Each barrel comes with a Carlson modified choke tube, manufactured from 17-4 stainless steel. Remington 870 barrels are threaded for the standard Rem Choke system. benelli barrels are threaded for the Benelli Mobil choke style system. Barrels are available for 12ga only.SPECS: 4140 steel, chrome lined bores, satin matte blue finish. Red fluo-rescent front sight , brass center bead.

CARLSONS

REPLACEMENT VENT RIB SHOTGUN BARRELS

Enhance The Versatility Of Your Shotgun

Stainless steel, hardened washer is spe-cifically shaped to retain the late-model Remington forend wood using the old-model magazine tube nuts. Allows you to install new model wood onto the older shotguns without hav-ing to drill the forend and stake in a magazine tube nut retain-ing detent. Can also be used to help retain worn Remington 870 magazine tube nuts. abSPECS: Stainless steel. Fits 12 gauge only. Sold in 3-Paks.

SPEEDFEED REMINGTON 1100

FOREND WAVE WASHERInterchange New Model Forends Without Detent Ball Installation

#838-000-021AQ Forend Wave Washer, 3-pak, 6K6N15 � � � � � � � � � � � � � � � � � � � � � � � $ 6.99

All-metal replacement for fac-tory triggerguard and fire-control system substitutes metal parts for

plastic for a more solid feel and extra strength, durability, and reliability to stand up to hard field or tactical use. Self-contained module is precision manufactured to original factory dimen-sions for an exact fit and easy, drop-in installation. One-piece aluminum housing with integral triggerguard provides excep-tional strength, while hardened steel internal parts, including trigger and hammer, ensure years of reliable function. Adds only 1.7 oz. to help preserve your gun’s original balance.SPECS: Aluminum housing, steel trigger components, black matte finish. Fits Mossberg 500 and 590, 12 ga. only.

MOSSBERG 500/590

TRIGGER HOUSING ASSEMBLYAll-Metal Factory Replacement

Stands Up To Hard Use

#631-000-337AQ Mossberg Trigger Assy, 1C78A88 � � � $ 92.99

stock # FIts Lgth chAMbeR choke PRIce#155-000-213AQ Rem 870 24" 3" Mod . 5E161F29 $ 173.99#155-000-214AQ Rem 870 26" 3" Mod . 5E161G28 $ 173.99#155-000-215AQ Rem 870 28" 3" Mod . 5E161L28 $ 173.99#155-000-216AQ Nova 24" 3 .5" Mod . 5E230B09 $ 247.99#155-000-217AQ Nova 26" 3 .5" Mod . 5E230N09 $ 247.99#155-000-218AQ Nova 28" 3 .5" Mod . 5E230I09 $ 247.99

PAGE 208 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

MA

gA

ZIn

e t

ub

es

& P

AR

ts

sht

og

un

Re

PL

Ac

eM

en

t P

AR

ts

Genuine factory replacement barrels let you pick the barrels you need. Choose short or long, smoothbore or rifled, bead, rifle sights or integral scope base, even a ported barrel that takes the kick out of heavy duck and goose loads. All with the full as-surance of Mossberg quality.SPECS: Steel. Finish: Blue (B), Matte Blue (MB), Extras: Vent Rib (VR). Ported (PR) Rifled Bore (RB). Choke: Cylinder (C), Sights: Rifle Sight (RS), Plain Bead (PB). Integral Scope Base (ISB). Accu-Mag is choke set for turkey and waterfowl.

MossbeRg 500 MuZZLeLoADIng conVeRsIon bARReL - –drops in to instantly convert your M o s s b e r g 500 or Maverick 88 shotgun into a 50 caliber muzzleloader. Requires no permanent modification to the shotgun. Uses common 209 shotgun primers and works with black powder and substitutes. Rifle sights help you get on target quickly. In-cludes brass-tipped synthetic ramrod that accepts popular ac-cessories. Barrel features 1-26" twist rate for best use with sabots or conicals. SPECS: Steel, blued finish. 24" (61cm) long. 50 caliber. Not for use with smokeless powder. Ramrod and instructions included. #631-000-363AQ Mossberg 500 Muzzleloading

Conversion Barrel, 1C134M79 � � � � � $ 149.99

MOSSBERG

REPLACEMENT SHOTGUN BARRELS

Mossberg Factory Barrels Give Factory Fit & Finish

stock # Length/gA./stYLe PRIce500 AND MAVERICK BARRELS

#631-000-302AQ 28" 12 Ga ., B, VR, PR 1C176F82 $ 189.99#631-000-307AQ 26" 20 Ga ., B, VR 1C174J29 $ 187.99#631-000-364AQ 24" 20 Ga . B, RS 1C137G68 $ 149.99#631-000-314AQ 20" 12 Ga ., B, RS, C, 8 shot 1C115I18 $ 141.99#631-000-358AQ 20" 12 Ga . B, VR, PB 1C180F69 $ 199.99#631-000-306AQ 18 .5" 12 Ga ., B, PB, C 1C90K00 $ 99.99

MOSSBERG 835 BARRELS#631-000-355AQ 28" 12 Ga . MB, VR, PR,

Accu-Mag 1C207L14 $ 219.99

#631-000-354AQ 24" 12 Ga . B, RS, PR 1C164K29 $ 179.99#631-000-362AQ 24" 12 Ga . B, RS, PR 1C131F03 $ 149.99#631-000-361AQ 24" 12 Ga . B, RB, ISB 1C187E14 $ 199.99#631-000-356AQ 24" 12 Ga . MB, RB, PR, ISB 1C207J14 $ 219.99

MOSSBERG 935 BARRELS#631-000-352AQ 24" 12 Ga . MB, RB, RS 1C227K54 $ 280.99#631-000-353AQ 24" 12 Ga . MB, RB, ISB 1C227F54 $ 280.99

MOSSBERG 930 BARRELS#631-000-359AQ 18 .5" 12 Ga . MB, PB 1C98B55 $ 109.99#631-000-350AQ 18 .5" 12 Ga . MB, PB 1C155B08 $ 191.99

Remington factory slug barrels are fully-rifled for best accu-racy with saboted slugs. Includes an integral cantilever scope base that ensures the scope will always be properly aligned with the bore, even if the barrel is removed for bird hunting and later reinstalled for deer season. SPECS: Steel, black oxide finish. Fits Remington 870 only. Chambered for 2¾" and 3" shells. 12 Gauge – 20" long, gloss finish. 20 Gauge – 18½" length, matte finish.

REMINGTON 870

RIFLED SLUG BARREL

Fully Rifled & Optics-Ready For Maximum Accuracy

#767-000-934AQ 12 Ga� Rem 870 Slug Barrel, 6G388F76� � � � � � � � � � � � � � � � � � � � � � � � � � $ 419.99

#767-000-935AQ 20 Ga� Rem 870 Slug Barrel, 6G266M90 � � � � � � � � � � � � � � � � � � � � � � � � � 289.99

Mossberg is well-known in the industry as a manufacturer of high-quality barrels for other gun makers. These steel barrels for Remington 870 shotguns come in several different lengths and styles for multiple uses. 12 gauge only. Choose from short or long, smoothbore or fully-rifled, bead sight, rifle sights and even integral scope base.SPECS: sPecs: Steel. blue or matte blue finish. Cylinder bore unless rifled. 12 Ga. only.

MOSSBERG

BARRELS for REMINGTON 870

Lengths & Styles To Customize Your Remington 870

stock # boRe sIghts FInIsh Length PRIce#631-000-346AQ Rifled Rifle Blue 24" 1C215M71 $ 229.99#631-000-345AQ Rifled Rifle Matte

Blue24" 1C215P71 $ 229.99

#631-000-344AQ Rifled Integral Scope Base

Blue 24" 1C215B71 $ 229.99

#631-000-347AQ Cylinder Bead Blue 18½" 1C128N28 $ 149.99#631-000-348AQ Cylinder Bead Matte

Blue18½" 1C134G79 $ 149.99

An impossible to get factory part that’s nec-essary to keep that 37A shooting. Locates the

forearm on the barrel and keeps the barrel from coming off. abSPECS: Plastic, black.

NU-LINE GUNS WINCHESTER

37A FOREARM SPACERRestore Your 37A To Shooting Condition

#655-003-037AQ 37A Forearm Spacer, 5E7A46 � � � � � � � � $ 9.95

Compact, 181/2" long factory barrels feature a tough-look-ing, crenelated muzzle that serves as a self-defense tool and a door breaching device for law enforcement/military person-nel. Permanent cylinder bore, chambered for 3" shells – buck-shot or slugs. Fiber optic red-dot front sight.SPECS: Steel, matte blued (MB) or semi-gloss blued (SGB) finish. 181/2" long when installed. 12 gauge only. 3" chamber. Not threaded for choke tubes.

Gives Your Shotgun An Integrated “Breacher”

Muzzle Device & Self-Defense Tool

#631-000-338AQ Moss 500 Standoff Barrel, MB, 1C138L46 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 149.99

#631-000-360AQ Moss 500 Standoff Barrel, SGB, 1C147E82 � � � � � � � � � � � � � � � � � � � � � � � � � � 159.99

#631-000-357AQ Moss 930 Standoff Barrel, MB, 1C218M84 � � � � � � � � � � � � � � � � � � � � � � � � � 269.99

MOSSBERG 500/930 STANDOFF BARREL

Tightens the loose barrel/barrel ex-tension fit common to older Model 97s and Model 12s. Provides a stronger, more secure lockup on guns that are adjusted to nearly maximum. .005" brass shims conform to action irregu-larities to improve thread engagement. abSPECS: Brass, .005" (.13mm) thick. Pack contains two shims.

GUN-SLICKER WINCHESTER 1897//12

BARREL SHIMSRestores “Factory-Fit” For Takedown Models

#100-000-629AQ 12 Gauge Barrel Shims, 7K11M96 � � � $ 14.95

Replacement barrel assemblies let you change the barrel length of your SLP for different hunting or shooting situations. Vent rib with front bead makes these barrels ready to use out of the box. Barrels are back bored for Invector Plus chokes, and in-clude one Invector Plus modified choke tube. Accepts 12 gauge shells up to 3" magnum. Includes two flexible magazine capac-ity reducers to fit standard and extended length magazines and choke wrench. SPECS: Steel, matte black finish. 12 ga.

FNH SLP

FACTORY BARREL ASSEMBLY

FNH Barrels For Factory Fit & Finish

#119-000-022AQ FNH SLP 24" Barrel, 9A368B06 � � � $ 369.99#119-000-023AQ FNH SLP 26" Barrel, 9A368F06 � � � 369.99#119-000-024AQ FNH SLP 28" Barrel, 9A368M06� � � 369.99#119-000-025AQ FNH SLP 30" Barrel, 9A368G06 � � � 369.99

High-capacity drum magazines are great for three-gun competition—fewer mag changes mean faster times and better scores. Made from hard-wearing, injection-molded polymer for reliable service. Access cover keeps out dirt, dust, and debris, yet can be removed for cleaning or maintenance. Due to varying toler-ances on Saiga shotguns, minor fitting may be required; fitting instructions included. 20-Rd model features a thumb activated slide assist to retain the spring to help you load rounds quickly. 12-Rd features a translucent cover to see how many rounds remain. abSPECS: Polymer, black/translucent. Fits Saiga 12 gauge shotguns only. Accepts 23/4" shells only. Instructions included. 20-Rd – 7" (17.8cm) dia., 3" (7.6cm) thick. 2 lbs., 4 oz. (1 kg) wt. 12-Rd – 5" (12.7cm) dia., 3" thick. 1 lb., 3 oz. (538 g) wt.

PRO MAG SAIGA 12

DRUM MAGAZINESuper-High-Capacity Mag For

Competition Or Recreation

#687-000-061AQ Saiga 12 Drum Magazine, 20-Rd, 7H80Q01 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 89.99

#687-000-062AQ Saiga 12 Drum Magazine, 12-Rd, 7H63K86 � � � � � � � � � � � � � � � � � � � � � � � � � � � 71.99

Lightweight, molded polymer magazine has reinforced steel feed lips to ensure reliable delivery of all 10 rounds to the chamber of your 12 gauge Saiga shotgun. Ideal for the three-gun competi-tion shooter, with deep, “waffle” texturing on the outside for a secure grasp during high-speed mag changes. Extra length ensures that even when ful-ly loaded there’s extra compressibility to the round

stack so the magazine can be inserted with the bolt closed. abSPECS: Reinforced injection-molded polymer, black. 10-round capacity. Fits Saiga 12 gauge shotguns only.

PRO MAG SAIGA-12

10-ROUND MAGAZINELightweight & Reliable-Feeding,

Ideal For Competition

#687-000-029AQ Saiga-12 Magazine, 7H28E24 � � � � � � � $ 31.99

High-capacity magazine of tough, light-weight polymer composite lets you load up and fire 12 rounds before reloading your Saiga 12-gauge shotgun—ideal for home defense or three-gun competition. Reinforced, injection molded Dupont™ polymer construction ensures durability and a slick, self-lubricating interior for fast, reliable feeding. Raised horizontal ridges on the grasping areas ensure a secure grip when re-moving and inserting mag into the gun. Remov-

able floorplate for easy cleaning; precision wound steel spring is treated with a corrosion-inhibiting coating for long-lasting protection from rust. Counts as three parts for compliance with U.S. Code Title 18 Section 922(r) part-source requirements. abSPECS: Fiberglass-reinforced, injection-molded Dupont polymer, black. 12 round capacity. Fits Saiga 12 gauge shotguns only.

SGM TACTICAL SAIGA 12

12-ROUND MAGAZINERugged, Smooth-Feeding, All-Polymer Construction

#100-005-783AQ 12-Rd Saiga Shotgun Magazine, 4D42C86 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 49.99

Durable, machined alumi-num plug limits the number of shells that can be loaded into the magazine of the Super Black Eagle, so hunters can com-ply with 3-shot migratory game bird laws. Lightweight plug assures the function and handling of your gun won’t be af-fected. abSPECS: Aluminum, natural finish. 41/8" (10.5cm) long, 3/16" (4.8mm) diam-eter shaft.

JARD BENELLI SUPER BLACK EAGLE

MAGAZINE PLUGKeeps You Compliant

With Game Laws

#100-002-572AQ Benelli Magazine Plug, 2K18Q86 � � � $ 21.99

Complete, factory barrel assemblies ensure proper fit and provide added versatility and maximum performance for your Remington VERSA MAX 12-gauge shotgun. Each comes with green fiber optic front sight and silver middle bead. Also fea-tures attached gas cylinder plugs, gas pistons, vent rib, and ejector with spring and retainer. Threaded for Remington Pro-Bore™ choke tubes only; barrels have one extended fit or flush fit tube installed.SPECS: Steel. Fits Remington VERSA MAX and VERSA MAX Sportsman®. Available in matte black, Mossy Oak® Duck Blind™ Camo, Realtree® AP™ HD™ Camo, and Mossy Oak® Break-Up Infinity™ Camo.

Replacement Barrels For VERSA MAX Shotgun

stock # choke FInIsh Lgth PRIce 767-000-937AQ Mod flush Matte black 28" 7F422D36 $ 449.99 767-000-938AQ Flooded Timber (Skeet)

extendedMossy Oak Duck Blind

28" 7F461A29 $ 576.61

767-000-940AQ Mod flush Matte black 26" 7F466G81 $ 583.51 767-000-939AQ Flooded Timber (Skeet)

extendedRealtree AP HD 26" 7F466P81 $ 583.51

767-000-941AQ Wingmaster HD Turkey/Predator (Full) extended

Mossy Oak Break-Up Infinity

24" 7F438G46 $ 523.99

767-000-936AQ Imp Cyl flush Matte black 22" 7F473K58 $ 583.99

REMINGTON® VERSA MAX®

FACTORY BARREL ASSEMBLIES

sho

tg

un

PAGE 209Orders/Tech: 800-741-0015order on the web

brownells.com

Fluorescent green,combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with

tapered tail to help prevent magazine spring bind and improve reliability. abSPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Rem-ington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.

SCATTERGUN TECHNOLOGIES

TACTICAL RESPONSE FOLLOWERSmooth-Feeding; Highly Visible

#800-100-004AQ Magazine Follower, 8Z7F10 � � � � � � � � � $ 8.99

Machined aluminum shotgun fol-lower features Teflon coating for smooth feeding. Bright wine-red color makes it easy to tell when magazine is empty. Available in 12 and 20 gauge, follower fits most shotgun magazine tubes. Will not fit Mossberg shotguns. abSPECS: SPECS: Aluminum, Teflon coated, wine red. 12 Gauge 1.1 (2.7cm) long. .9 (2.2cm) O.D. 20 Gauge 1.1 (2.7cm) long. .7 (1.7cm) O.D.

NORDIC COMPONENTS

LOW DRAG SHOTGUN FOLLOWERS

Teflon-Coated Follower Helps Smooth Feeding

12 Ga.

#100-011-061AQ Low Drag Follower, 12 Ga., 1B14D59 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 18.00

#100-011-062AQ Low Drag Follower, 20 Ga., 1B14D59 � � � � � � � � � � � � � � � � � � � � � � � � � � 18.00

20 Ga.

Lightweight aluminum or stainless steel followers for Remington, Mossberg, and Benelli shotguns. Tough construction holds up to years of competitive and law enforce-ment shooting and won’t wear out after thousands of rounds, break under spring pressure, or degrade when cleaning sol-vents are used. Bright colors let you see immediately if the magazine is empty. Vented design reduces weight to help pro-mote smooth feeding. Stainless steel (SS) followers are natural finish. Aluminum followers are available in red, orange, green and black, depending on model and gauge. abSPECS: Aluminum or stainless steel. Benelli does not fit Nova or Super Nova, fits 12-gauge 3" Magnum guns.

STK# MOSS12 GA.

STK# BENELLI 12 GA.-3" MATErIAL COLOr

#080-000-233AQ NA Alum Green#080-000-167AQ #080-000-171AQ SS Natural#080-000-232AQ NA Alum Orange#080-000-168AQ #080-000-172AQ Alum Red

— Advise # — Shotgun Follower, 8K17C51 � � � � � � � � � � � $ 21.99

SHOTGUN FOLLOWERSTough, Durable Replacement

For Factory Followers

STK# 12 GA. STK# 20 GA. MATErIAL COLOr#080-000-175AQ NA Alum Green#080-000-226AQ #080-000-229AQ SS Natural#080-000-237AQ #080-000-238AQ Alum Orange#080-000-227AQ #080-000-166AQ Alum Red

— Advise # — TWS Ammunition, 8K17K51 � � � � � � � � � � � $ 21.99

Ever spent the better part of an afternoon “manufacturing” a new magazine plug for a customer? It’s a trial-and-error pro-cess that keeps the customer happy but makes you poor. With our universal “Fits-All” Plug, all that’s required is a simple “snap” at the correct notch to fit all popular shotguns. For those oddball guns with non-standard length magazines, simply “notch” the “Fits-All” with a shop knife at the length required and “snap”! It’s that easy! Complete instructions and convenient “Snap-To- Fit Chart” included. Made of unbelievably tough polypropylene with an oversize head to position it correctly in all magazines - Won’t slide or rattle. Bright, safety-orange color is easy to see and find. Fast, economical way to help your customers comply with migratory game bird laws. abSPECS: 109/16" (26.8cm) long. 9/16" (14.3mm) diameter head. 3/8" (9.5mm) ribbed body.

“FITS-ALL”

SHOTGUN MAGAZINE PLUG

Universal - “Snaps” At Notches To Fit All Gauges & Lengths; Fits More Guns Than Other Plugs - Orange, Poly Plastic

#084-115-001AQ 1 Shotgun Mag. Plug, 6K4M47 � � � � � � � $ 6.99#084-115-006AQ 6 Shotgun Mag. Plugs, 4H18M50 � � � � 29.99#084-115-012AQ 12 Shotgun Mag. Plugs, 4H32N50 � � � 49.99

Easy-to-install kit includes long-wearing, ABS nylon, high- visibility, fluorescent green follower for improved feeding. Plus, the Wolff spring relieves spring bind, and won’t “set”. abSPECS: Fits Rem. 870, 1100, 11-87, SPT-12. Springs and follower will fit most 12 ga. shotguns with standard magazine tubes, plus those equipped with one- or two- round (6 or 7 shot) extensions.

SCATTERGUN TECHNOLOGIES

MAGAZINE SPRING PACKAGE

For Law Enforcement & Self-Defense Shotguns

#800-120-005AQ 5 Shot Perf. Packages, 8Z10H48 � � � � $ 12.99#800-120-007AQ 7 Shot Perf. Packages, 8Z10C30 � � � � 14.99#800-120-107AQ 7 Shot Spring, only, 8Z7I78 � � � � � � � � � 9.99

High-visibility stainless steel follower replaces the factory follower in Remington 870 and 11-87 shotguns. Won’t break under spring pressure, won’t rust and holds up to years of shooting. Bright stainless steel makes it easy to see how many rounds are left in the magazine tube. Ribbed side and drilled out center hole reduce weight without jeopardizing overall strength. abSPECS: Stainless steel. 5/8" (1.6cm) long. 12 ga. - 7/8" (22mm) dia. 20 ga. - ¾" (19.1mm) dia.

VANG COMP SYSTEMS REM 870/11-87

STAINLESS STEEL FOLLOWERStrong, Dependable Replacement For

Factory Followers

#100-002-463AQ 12 Ga. SS Follower, 6K10Q69 � � � � � � � $ 18.99 100-009-761AQ 20 Ga. SS Follower, 6K10C69 � � � � � � � 18.99

Joins barrel and extended mag tubes to keep extra weight from pulling gas system out of alignment. abSPECS: Steel, matte blued. Fits most single barrels.

CLARK CUSTOM

SHOTGUN MAGAZINE BANDSupports Extended Magazines

& Counter Weights

#181-380-001AQ Magazine Band, 1H38C10 � � � � � � � � � � $ 45.99

Lightweight, aluminum clamp locks barrel and extended magazine tube to-gether to form a rigid, rock-solid assem-bly. Can be used as a tactical light mount: install a 1" diameter light in one side of

the clamp and secure the other side to the barrel or maga-zine. Left- and right-side sling swivel sockets accept standard pushbutton swivels. Two steel Allen head screws pull the clamp halves together for a tight, non-slip hold. Also available with a 2" long, 4-slot, MIL-STD 1913 Picatinny rail that can be installed in the 3- or 9- o’clock position, for mounting additional acces-sories. Fits Remington 870, 1100, 11-87 and Benelli M1, M2, M4, M1014, 12 gauge shotguns. abSPECS: 6061 T6 aluminum, mil-spec Type 3 hardcoat anodized, matte black. Clamp - 11/2" (3.8cm) long, 17/16" (3.5cm) wide, 15/8" (4.1cm) high. Rail - 2" (5.1cm) long. Includes mounting hardware. Fits Remington 870/1100/11-87 and Benelli M1/M2/M4/M1014, 12 gauge only.

MESA TACTICAL REMINGTON/BENELLI

TACTICAL BARREL/MAGAZINE CLAMPSecures Extended Mag Tube

& Mounts Accessories Up Front

#100-004-032AQ Barrel/Mag Clamp, w/Rail, 5A75K89 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 83.99

#100-005-447AQ Barrel/Mag Clamp, Only, 5A54C99� � � � � � � � � � � � � � � � � � � � � � � � � � � � 54.99

Precision-machined aluminum extension tubes increase the magazine ca-pacity of your 12-gauge Benelli, Beretta, or Winchester shotgun. Each tube has an ex-tra-thick wall for added rigidity and strength. Ideal for shoot-ing competitions, law enforcement, and home defense. Screws onto the factory magazine threads for fast installation in min-utes. Knurled grasping surfaces aid installation and removal for cleaning. abSPECS: 6061 T6 aluminum, black finish. Fits 12 gauge only. Includes tube extension, tube connector, spring, and follower.

BRILEY SHOTGUN MAGAZINE EXTENSION TUBE

Increases Round Capacity; Easy To Install;

Rugged, All-Metal Construction

STOCK # rDS FITS PrICE#129-000-265AQ 3 Benelli M1/M2/Super 90/

SBE/SBE II9B77N10 $ 87.99

#129-000-267AQ 5 Benelli M1/M2/Super 90/SBE/SBE II

9B81M39 $ 91.99

#129-000-264AQ 3 Beretta Extrema I/II, Benelli Nova/Super Nova

9B77J10 $ 87.99

#129-000-266AQ 5 Beretta Extrema I/II, Benelli Nova/Super Nova

9B81K39 $ 91.99

#129-000-263AQ 3 Winchester Super X3 9B81K39 $ 91.99

Strong, lightweight, extruded aluminum tube increases the magazine capacity of 12 gauge shotguns. Features a machined clamp groove that eliminates clamp slip due to recoil and helps prevent point of impact shifts or damage to the barrel’s finish. Reinforced end cap resists heavy impacts, and threads on both ends of the tube body allow the user to flip it to best match the clamp groove location to the shotgun. Installs in minutes using a machined union nut that attaches to the end of the factory tube. Some models may require removal of factory magazine tube crimp. Use the factory follower and the extended maga-zine spring provided with the Nordic MTX tube. All models fit 12 gauge only. abSPECS: CNC machined aluminum, hardcoat anodized, matte black. 12 gauge only. Benelli fits M1/M2, Super Black Eagle I & II. Benelli Nova fits Nova/Super Nova, Beretta X-trema/X-trema 2, Tx4, A400 and CZ 712. Mossberg fits 590, 930 and 935. Remington fits 870, 1100, 11-87 and 105 CTi. Winchester fits SX2/SX2, Browning Gold/Silver, FN SLP. NOTE: Tube threads not compatible with Nordic XX, XL and XXL end caps.

SUPPOrT CLAMP - Strong, lightweight aluminum clamp attaches securely to barrel to provide extra support for ex-tended magazine tube. Eliminates un-wanted vibration under recoil to ensure smooth, reliable feeding of rounds. Low-profile design, rounded edges, and flush-mounted hex-head machine screws prevent snags and damage to patrol car interiors; hardcoat anodized surface adds strength and exceptional resistance to surface abrasion. Available in Standard model and Tactical rail configuration with Picatinny-type accessory rail that may be positioned on left or right side of clamp for mounting flash-lights and other accessories. SPECS: Aluminum, hardcoat anodized, black, matte finish. Fits shotguns equipped with Nordic and DPMS extension tubes. 12 gauge only. Stan-dard - 2 oz. (57g) weight. Rail - 2.6 oz. (73g) weight.#100-003-183AQ Magazine Extension Clamp,

1B24L49 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 30.99#100-003-182AQ Mag. Extension Clamp w/Tactical

Rail, 1B37I59 � � � � � � � � � � � � � � � � � � � � � � � 45.99

NORDIC COMPONENTS

MTX EXTENDED SHOTGUN MAGAZINE TUBES

Screw-On Extender Bumps Up Your Shotgun’s Mag Capacity

STOCK # FITS +rDS PrICE#100-011-497AQ Benelli 2 1B59N95 $ 75.99#100-012-470AQ Benelli 3 1B59J95 $ 75.99#100-011-499AQ Benelli 7 1B59K95 $ 75.99#100-011-500AQ Benelli 9 1B59J95 $ 75.99#100-011-509AQ Benelli Nova 7 1B59N95 $ 75.99#100-011-505AQ Mossberg 2 1B59M95 $ 75.99#100-012-473AQ Mossberg 3 1B59Q95 $ 75.99#100-011-506AQ Mossberg 7 1B59J95 $ 75.99#100-011-501AQ Remington 2 1B59H95 $ 75.99#100-012-472AQ Remington 3 1B59E95 $ 68.99#100-011-502AQ Remington 5 1B59N95 $ 75.99#100-011-503AQ Remington 7 1B59G95 $ 75.99#100-011-504AQ Remington 9 1B59F95 $ 75.99#100-012-474AQ Winchester 3 1B59J95 $ 75.99#100-011-507AQ Winchester 7 1B59N95 $ 75.99#100-012-181AQ Rem. VERSA MAX 3 1B59B95 $ 75.99#100-012-182AQ Rem. VERSA MAX 5 1B59F95 $ 75.99#100-012-183AQ Rem. VERSA MAX 5 1B59P95 $ 75.99

MA

GA

zIN

E T

UB

ES &

PA

rT

S

Ga.

sho

tg

un

PAGE 210 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

Gives you additional magazine capacity in only a minute. Quick and simple to install and remove. Threaded tube replaces magazine cap. Perfect for action shooting events or Law En-forcement. remington and Benelli/ Beretta models only come with sling swivel clamp that secures the extension to the barrel for extra support. Provides a convenient front mounting point for carry strap or sling. abSPECS: Extension - Steel, blued or Parkerized, matte finish. Models for 12 ga. and 20 ga. only. Includes extended spring, follower and swivel clamp. Sling Swivel Clamp - Blued or Parkerized steel, front and rear 1" swivel rings with studs. Chart indicates number of ROUNDS (RDS) in addition to factory magazine capacity for each model.

CHOATE

SHOTGUN MAGAZINE EXTENSION

Screw-On Tubes For Increased Capacity

STOCK # rDS FITS PrICE12 GA. BLUE MAGAZINE EXTENSIONS

#159-000-025AQ 2 Benelli Nova, Beretta Extrema 9E39D37 $ 43.99#159-000-026AQ 4 Benelli Nova, Beretta Extrema 9E39I37 $ 42.99#159-000-027AQ 4 Benelli SBE/SBE II/M1/M2 9E42D83 $ 47.99#159-102-870AQ 2 Rem. 870/1100/11-87* 9E39I77 $ 44.99#159-102-873AQ 3 Rem. 870/1100/11-87* 9E39A77 $ 44.99#159-102-874AQ 4 Rem 870/1100/11-87* 9E42N83 $ 47.99#159-102-875AQ 5 Rem. 870/1100/11-87* 9E44N36 $ 49.99#159-105-120AQ 5 Winchester 1200 9E44K36 $ 49.99#159-102-550AQ 2 Mossberg 500/590/935 9E39P77 $ 44.99#159-102-555AQ 5 Mossberg 500/590/935 9E44C36 $ 49.99#159-000-011AQ 3 Mossberg 835 (B) 9E39Q77 $ 44.99

20 GA. BLUE MAGAZINE EXTENSIONS#159-000-006AQ 2 Remington (B) 9E39H77 $ 44.99#159-000-007AQ 3 Remington (B) 9E39A77 $ 44.99#159-000-008AQ 4 Remington (B) 9E42M83 $ 47.99#159-000-009AQ 5 Remington (B) 9E44A36 $ 49.99

12 GA. PARKERIZED MAGAZINE EXTENSIONS#159-104-872AQ 2 Rem. 870/1100/11-87* 9E39D77 $ 44.99#159-104-873AQ 3 Rem. 870/1100/11-87* 9E39D77 $ 44.99#159-104-874AQ 4 Rem .870/1100/11-87* 9E42Q83 $ 47.99#159-104-875AQ 5 Rem. 870/1100/11-87* 9E44L36 $ 49.99#159-000-013AQ 3 Mossberg 835 (P) 9E39A77 $ 44.99

Machined steel magazine extensions in-crease capacity without

gunsmithing or permanent alterations to your Remington 870, 1100 or 11-87 shotgun. Knurled, threaded collar screws onto the end of the mag tube. Includes high-performance, extended length magazine spring and an unbreakable, high-visibility, nylon follower. Loop models features a stationary loop on ei-ther the bottom or left side of the extension to accept direct attachment of tactical-style slings without swivels. QD stud models include a quick-detach, swivel stud mounted either in the center of the magazine cap or at the front of a plate below the extension to accept slings with quick-detach swivels. All models fit 12 gauge only. abSPECS: Steel, gray parkerized finish. Fits Remington 870/1100/11-87, 12 ga. only.1-Shot - 2" (5cm) long, 2-Shot - 6" (15.2cm) long.

SCATTERGUN TECHNOLOGIES

EXTENDED MAGAZINE TUBEAdds One Or Two

Additional Rounds To Your Remington

Shotgun

STOCK # EXTrA rOUNDS SLING LOOP LOCATION#800-720-700AQ 1 Loop, bottom#800-710-990AQ 1 Loop, left-side#800-000-003AQ 1 QD stud, mag cap#800-730-080AQ 2 Loop, left-side#800-000-004AQ 2 QD stud, front

— Advise # — Extended Magazine Tube, 8Z43A15 � � � $ 44.99

Easy-to-install magazine extension increases your 12 gauge shotgun’s capacity by up to four additional 23/4" shells. Perfect for competition, law enforcement, or home defense use. Corrosion-resistant, stainless steel tube with machined aluminum mounting collar, high strength stainless steel spring, and anodized aluminum follower help ensure reliable feeding in the harshest salt water, marsh hunting, or tactical environment. Installs in minutes, no special tools required. abSPECS: Stainless steel tube, anodized aluminum mounting collar and follower, stainless steel spring, steel barrel clamp with sling loop (some models). All models fit 12-gauge only. M4 kit contains extension tube, spring, and follower only. Benelli fits Super Black Eagle I and II, M1, M2, and M1 Super 90. Benelli M3 fits Benelli M3 shotguns only. M4 fits Benelli M4 shotguns only. Beretta fits A391 3.5 Extrema, Extrema2, Benelli Nova, Benelli Super Nova, and Franchi 912 & 612. Brown/Win fits Browning Gold and Winchester Super X2/X3.

SRM PERFORMANCE

MAGAZINE TUBE EXTENSION KIT

Increases Capacity For Law Enforcement, Competition Or Home Defense

STK# 2-rD STK# 3-rD STK# 4-rD FITS#100-002-831AQ #100-002-832AQ #100-000-586AQ Benelli#100-003-176AQ NA NA Bennelli M3#100-002-803AQ NA NA Benelli M4#100-002-835AQ NA #100-000-587AQ Beretta

NA NA #100-000-588AQ Brown/Win

— Advise # — Magazine Extension Kit, 1K89B59 � � � � $ 99.99

Dependable, factory made magazine extensions provide ad-ditional round capacity for tacti-cal operations and competition. All-steel extension tubes attach directly to the end of the magazine tube to increase total capacity by as much as three rounds. Included magazine clamp attaches around the barrel and the extension for added support. Magazine spring is formed from high strength music wire that resists “set” and won’t weaken over time. Mod-els available with 13/8" swivel loop and clamp-mounted swivel stud. Available with matte blue or Parkerized finish.SPECS: Steel, matte blue or Parkerized finish. Includes magazine exten-sion spring, clamp, and forend nut. Rounds (Rd) indicates number of additional rounds extension adds to factory magazine capacity. Fits Rem-ington 870, 12 ga. only.

REMINGTON REM 870

MAGAZINE EXTENSIONSGenuine, Factory Brand

Extensions Increase Mag Tube Capacity

#767-000-527AQ 2-Rd Mag Ext, Park, 7F82P34 � � � � � � � $ 89.99 767-000-710AQ 2-Rd Mag Ext w/Swivel, Parkerized,

7F95D17 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 117.99#767-000-714AQ 3-Rd Mag Ext w/Swivel, Parkerized,

7F129N60 � � � � � � � � � � � � � � � � � � � � � � � � � � � 139.99#767-000-528AQ 3-Rd Mag Ext, Blue, 7F60K86 � � � � � � � 64.99

Extra-power magazine spring ensures that every shell is ready to be loaded when you need it. Orange aluminum follow-er lets you see at a glance when the magazine is empty. Drop-in installation requires no special tools. Instructions included. abSPECS: Steel magazine spring. Aluminum follower, orange. Fits Reming-ton 870, 12 gauge.

REM 870

XP MAGAZINE SPRING & FOLLOWER

Feeds Shells Smoothly; Bright Follower Indicates Magazine Is Empty

#080-000-083AQ XP Mag. Sprg w/ Fllwr, 8K21A11 � � � � $ 25.99

Long-lasting, magazine springs are made from 17-7 stainless steel to help prevent malfunctions caused by rusty magazine springs. Heat treated for durability and superb per-formance. Fits Remington 870 with two-round magazine ex-tension. Can replace standard magazine tube springs but will require trimming. abSPECS: 17-7 stainless steel. 23" (58.4cm) OAL.

REMINGTON 870 STAINLESS STEEL EXTENDED MAGAZINE TUBE SPRING

Eliminates Magazine Spring Corrosion

#084-000-154AQ S/S Extended Magazine Tube Spring, 6Z15D05 � � � � � � � � � � � � � � � � � � � $ 18.80

Long-lasting magazine spring helps ensure positive, reliable feeding. Springs come extra long so you can custom trim for per-fect fit. Easy drop-in installation. Available in 12 ga. and 20 ga. abSPECS: Steel magazine spring. 12 ga. - 45" (1.1m) long. 20 ga. - 40" (1m) long.

NORDIC COMPONENTS

EXTENDED MAGAZINE TUBE

SPRINGExtra-Long Spring

Lets You Trim For Perfect Fit

#100-009-312AQ Magazine Tube Spring, 12 ga., 1B5D72 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 7.55

#100-009-313AQ Magazine Tube Spring, 20 ga., 1B5H72 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7.55

High-tensile strength, precision-made, carbon steel springs from Wolff help you achieve reliable cycling and top performance from both hunting and competition shotguns. Replace weakened springs for better performance or use as part of a custom project for ultimate reliability. abSPECS: High-tensile, heat-treated spring steel. Gunsmith fitting required for some springs as indicated.

XP MAGAzINE TUBE SPrING - Provides 20% extra power (XP) over factory original magazine spring for 12 gauge shotguns. Measures 40" long and will fit all 3- to 5-round factory maga-zine tubes. All springs may require gunsmith fitting.#969-000-155AQ 12 Ga. XP Mag. Spring, Each,

9F3K67 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 5.49#969-651-660AQ 12 Ga. XP Spring, 10-Pak, 9F19E00 � � � 28.50

PrE-FIT rEM 870 XP MAGAzINE TUBE SPrING - Wolff’s excep-tional quality, extra power shotgun magazine tube springs ready to drop-in to the models listed below – no gunsmith-ing required. 10% extra power and fits 3- to 5-round 12 gauge magazine tubes.#969-000-067AQ Rem 870 XP Mag. Spring, each,

9F4H67 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 6.99#969-000-068AQ Rem 870 XP Mag. Spring, 5-pak,

9F20F00 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29.99

BENELLI rECOIL SPrING - Use 25% extra power (XP) recoil spring for heavy loads; 25% reduced power (rP) for light, trap/skeet loads to ensure maximum performance and service life from hunting and competition shotguns. Fits Super 90, Super Black Eagle, Montefeltro, and M1 models.#969-000-090AQ Benelli XP Recoil Spring, 9F9Q99 � � $ 12.99#969-000-091AQ Benelli RP Recoil Spring, 9F9H99 � � 12.99

WOLFF

SHOTGUN SPRINGS

Improves Function & Reliability

MA

GA

zIN

E T

UB

ES

& P

Ar

TS

Ideal for competition shooting, home defense, and law enforce-ment, these extension tubes in-crease the magazine capacity on your Remington, Benelli, CZ, and Beretta shotguns. Constructed of blued steel, extensions come with spring, base clamp, and a high vis-ibility follower. No modification

needed, simply remove the magazine cap and replace it with one of these threaded extension tubes. Benelli M4 7 shot exten-sion tube does not include clamp or follower. Remington ex-tensions require removal of tabs in magazine on newer model shotguns. Extensions available in 12 gauge only. abSPECS: Steel, blued finish. Includes spring, base clamp, and follower. Magazine round count based on 2 3/4" shells. Fits 12 ga. only.

CARLSON’S SHOTGUN MAGAZINE EXTENSION TUBES

Adds Firepower To Your Favorite Shotgun

STOCK # FITS +rDS PrICE#100-013-348AQ Benelli Nova/Super Nova, CZ

712/912, Beretta Extrema I/II 7 5E48H30 $ 50.95

#155-000-222AQ Benelli M4 7 5E47B90 $ 50.99#100-013-351AQ Benelli Nova/Super Nova,

Beretta 13018 5E48J86 $ 51.95

#100-013-347AQ Benelli M1/M2/SBE 8 5E48P86 $ 51.95#100-013-350AQ Remington 870/1100/11-87 7 5E48B30 $ 50.95#100-013-346AQ Remington 870/1100/11-87 8 5E48B86 $ 51.95#100-013-349AQ Remington 870/1100/11-87 10 5E51F07 $ 53.95

sho

tg

un

PAGE 211Orders/Tech: 800-741-0015order on the web

brownells.com

STO

CK

S

All-steel extension tubes attach directly to the end of the magazine tube and increase capacity by as much as five rounds. Extension cap is machined from solid steel and welded to seamless steel tubing for extra strength. Includes extended magazine spring. Barrel Magazine Clamp (BMC) - Clamps to the barrel and the extended mag tube. Stabilizes and supports the tube; includes built-in sling swivel stud. Benelli 3-round and Remington 5-round magazine extensions include barrel magazine clamp. Barrel clamp available separately for all other models. abSPECS: Steel, blue, matte finish. 12 ga. only. Rounds (RDS) indicates number of rounds extension adds to factory magazine capacity model. BMC-R Clamp - Fits Benelli Nova/Super Nova/M4, Rem. 870, and Win. 1200/1300 Def. BMC-U Clamp - Fits Rem. 1100/11-87.

TACSTAR SHOTGUN

MAGAZINE EXTENSION

No Gunsmithing Required; Increases Mag Tube Capacity

STOCK # rDS FITS PrICE#867-000-014AQ 2 Benelli Nova/Super Nova 7F43P56 $ 47.99#867-000-016AQ 2 Benelli M4 7F43D56 $ 47.99#867-103-102AQ 2 Rem. 870/1100/11-87 7F43L56 $ 47.99#867-103-202AQ 2 Win. 1200/1300 Def. 7F43L56 $ 47.99#867-000-015AQ 3 Benelli M1/M2/Super

Black Eagle I & II7F44J21 $ 48.99

#867-103-103AQ 3 Rem. 870/1100/11-87 7F44E21 $ 48.99#867-103-105AQ 5 Rem. 870 7F48A77 $ 53.99#867-103-115AQ 5 Rem. 1100/11-87 7F48N77 $ 53.99

#867-103-100AQ BMC-R Mag. Clamp, 7F10C41� � � � � � � $ 11.99#867-103-200AQ BMC-U Mag. Clamp, 7F10C41 � � � � � � 11.99

Short, screw-on magazine extensions add one or two ad-ditional rounds to tactical and sporting shotguns without in-creasing overall gun length. Replaces factory magazine cap with no permanent modifications. Machined from solid steel bar stock for a much stronger system to resist dents. Included sling loop can be installed for left- or right-handed shooters. Smooth-feeding, unbreakable follower is molded in bright green for easy inspection upon loading/unloading. Models available for Remington 870/1100/11-87 and Mossberg 590A1 shotguns. abSPECS: Steel, black matte finish. Includes extension tube, follower, and extended magazine spring. Accepts 11/4" slings. 12 ga. only. 1-Shot – 21/4" (5.9cm) long. Models for Remington 870/1100/11-87 and Mossberg 590A1. 2-Shot – 63/16" (15.7) long. Fits Remington 870/1100/11-87.

VANG COMP SYSTEMS

SHOTGUN MAGAZINE TUBE EXTENSION

Increased Round Capacity For Remington & Mossberg Shotguns

#100-003-057AQ 1-Shot Rem Magazine Tube Extension, 6K64L29 � � � � � � � � � � � � � � � � $ 74.99

#100-003-058AQ 1-Shot Moss Mag Tube Ext, 6K64E29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 74.99

#100-003-056AQ 2-Shot Rem Mag Tube Ext, 6K64D29 � � � � � � � � � � � � � � � � � � � � � � � � � � � 74.99

Kit SS-311 provides the highest quality action-tuning springs by Wolff to help the model 311 shotgun “hang” open for reloading, gives less cocking effort. Contains (2) factory standard hammer springs, (1) 15% RP sear spring, (2) 30% RP hammer springs, and (1) 15% RP top lever spring. abSPECS: RP = Reduced Power.

PRO-SPRINGS FOR SAVAGE/STEVENS 311

#080-665-311AQ Kit SS-311, 6K20E33 � � � � � � � � � � � � � � � � $ 30.24

Lighten trigger pull, hammer weight and break-open pressure with these Wolff springs designed for Ste-vens 311 series and similar shotguns used for action shooting. Sear spring lightens trigger pull for improved trigger control and the two hammer springs work with the top-snap spring to reduce cocking and break-open pressure for quick, smooth operation. Gunsmith installation recommended. abSPECS: Spring steel. Kit includes sear spring, two (2) hammer springs, and top-snap spring. Fits Stevens 311 A,C,D,E,F and H, 5100, 530, A; Springfield 511 and Series A; Savage Fox BDE, BSE C,D,E,F and H; BST B-C, B-D, B-E, and B-F.

WOLFF STEVENS 311

TRIGGER & HAMMER SPRING PERFORMANCE PAK

Lighten Trigger Pull, Hammer Weight &

Break-Open Pressure

#969-000-085AQ Stevens 311 Spring Pak, 9F13F33 � � � $ 19.99

High-quality top lever spring with washer provides

smoother function of the lever and lessens the effort required to break open the action for reloading. Speeds your reload time for improved cowboy action scores. Coils are slightly reduced in diameter to eliminate spring bind on the rod. abSPECS: Spring steel. Includes top lever spring, washer, and instructions.

LEE’S GUNSMITHING STOEGER IGA

GUNSLINGER TOP LEVER SPRING KITLessens The Effort Required

To Open The Action; Smoothes Operation

#100-000-513AQ Stoeger IGA Spring Kit, 5K9D25 � � � � $ 14.99

“V” mainsprings for side-by-side and over/under shotguns. Will handle most of your needs for foreign guns. Can be fitted to different length requirements.SPECS: Kit contains 8 springs, 1 each of these spring types: I-124, I-125, S-39, 654, 12840, 12842, 12850, 12854.

SHOTGUN

MAINSPRING KITUniversal Fit

#754-900-000AQ Mainspring Kit 9MK, 4E89N99 � � � � � $ 89.99

Top lever shotgun springs, made extra long, so they can

be cut to fit most European shotguns.SPECS: Kit contains 5 springs, 1 each of these spring types: I-121, S-30, 12944, 12948, 12952.

SHOTGUN

TOP LEVER KITOver-Length For Custom Fit

#754-800-000AQ Top Lever Kit, 4E73F99 � � � � � � � � � � � � � $ 73.99

Double torsion spring restores reliable hammer strike and posi-tive ignition on older Topper-se-ries guns. abSPECS: Steel. Fits Topper shotguns us-ing a double torsion hammer spring. Will not fit newer guns with a single torsion spring.

#969-000-069AQ H&R Hammr Sprg, Each, 9F4C67 � � � � $ 6.99 969-000-070AQ H&R Hammr Sprg, 5-pak, 9F15N34 � � 22.99

WOLFF H&R TOPPER

HAMMER SPRINGRestores Reliability & Performance

Direct, drop-in replacement for factory forend has plenty of Picatinnystyle rail space for mounting lights, lasers, and other tactical accessories. Features a full length, 6" bottom rail, and two detachable 21/2" long side rails. Lightweight, rugged polymer construction with deep “V” grooves on the gripping surface that ensure you keep a secure purchase on the weapon for fast, reliable cycling.SPECS: High-density, reinforced polymer, black. Fits Mossberg 500/590 12 ga.

COMMAND ARMS MOSSBERG 500//590

TRIPLE RAIL FORENDRigid, Lightweight

Picatinny-Rail Platform For Tactical Accessories

#100-004-628AQ Mossberg 500/590 Railed Forend, 6C47K73 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 57.60

MA

GA

zIN

E T

UB

ES &

PA

rT

S

High-density, lightweight polymer forearm features three MIL-STD 1913 Picatinny rails positioned at the 3-, 6-, and 9- o’clock positions for mounting a variety of tactical accesso-ries. Features a full length, fixed rail on the bottom with plenty of space to accommodate both a vertical grip and offset light mount. Two, ultra compact front side rails are just the right size for an additional light or laser mount and easily remove with an Allen wrench if not needed. Hand-filling, pump slide with embossed sides provides a comfortable, non-slip textured sur-face that grips your hand when shooting and cycling rounds. Available for Remington 870, 12 gauge only.SPECS: High-density polymer composite, black. 8" (20cm) long x 21/8" (5.4cm) wide. 7 oz. (198g) weight. Fits Rem. 870, 12 gauge only.

COMMAND ARMS REMINGTON 870

TRIPLE RAIL FORENDMounts Additional

Accessories For Tactical Operations

#100-004-107AQ Rem 870 Triple Rail Forend, 6C45K12 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 54.00

Rigid, lightweight reinforced composite handguard directly

replaces the Remington 870 factory forend to provide much needed rail space for tactical shotguns. Full length fixed rail on the bottom side accommodates a vertical grip. Compact side rails provide the right amount of space for lights, lasers and other small accessories, and are easily removed with an Allen wrench if not needed. Ribbed texture provides a non-slip surface during 3-gun competition or high-stress tactical maneuvers. Fits 12 gauge only.SPECS: Reinforced polymer composite, black. 71/4" (18.4cm) long x 115/16" (4.9cm) wide. 6.7 oz. (190g) weight. Fits Rem. 870, 12 gauge only.

FAB DEFENSE REMINGTON 870

PICATINNY RAIL HANDGUARDLightweight, One-Piece

Construction With Plenty Of Rail Space

#100-003-845AQ Rem. 870 Handguard Rail, 2B53N49 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 59.99

Ultra-strong, light-weight, slide assembly replaces your shotgun’s forend with three MIL-STD 1913 Picatinny rails positioned at 3, 6, and 9 o’clock for mounting tactical lights and other accessories. Nine, removable rubber rail covers let you expose the exact parts of the rail needed for accessory attachment, while covering the rest of the rails with a comfortable, no-slip gripping surface that protects your hand when shooting and cycling rounds. Models available for Remington 870 and Mossberg 500/590. abSPECS: Extruded aluminum, matte black. Rubber rail covers, black. Rem 870 – 61/4" (15.9cm) long. Moss 500/590 - 73/4" (19.7cm) long. Fits guns with 63/4" long factory forend; will not fit guns with forend metal for 73/4" factory forend.

FALCON INDUSTRIES

ERGO GRIP® 3-RAIL SHOTGUN FOREND

Easily Converts Shotgun For Tactical Applications

& Accessories

#573-000-039AQ Rem. 870 Forend, 3G63B49 � � � � � � � � � $ 67.99#573-000-045AQ Moss. 500/590 Forend, 3G64I26 � � � � 69.99

C o m fo r t a b l e , rubber over-mold-ed pistol grip and forend provide maximum perfor-mance and recoil control in all types of shooting scenarios. Advanced Tamer technology features an internal Sorbothane cushion that helps dampen felt recoil in the web of the hand. Pistol grip design includes dual palm swells and equally proportioned finger grooves, allowing both right- and left-handed opera-tors to shoot with confidence. Pebble textured rubber surface provides a firm grip even when wet. Models available for Rem-ington 870, Mossberg 500, 590, and 835. Rem. model includes 11/8" wide sling loop molded into pistol grip.SPECS: Molded polymer, overmolded rubber, black. Rem. - Forend is 71/2" (19cm) long, 13/4" (4.4cm) wide, 13/4" (4.4cm) high. Grip - 6" (15.2cm) long. Mossberg - Forend is 73/4" (19.7cm) long, 17/8" (4.7cm) wide, 13/4" high. Grip - 53/4" (14.6cm) long.

HOGUE REMINGTON/MOSSBERG

TAMER PISTOL GRIP & FOREND

#408-000-054AQ Rem. Tamer Grip & Forend, 8K29J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 31.99

#408-000-076AQ Moss. Tamer Grip & Forend, 8K27F99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 30.19

Hand Filling For Maximum Grip & Control

Smooth Gripper-style pistol grip converts your Remington or Mossberg shotgun into an ef-fective tactical gun. Provides a firm, no-slip grip, excellent recoil

absorption, and increased comfort and control. Requires no permanent modifications to gun. abSPECS: Checkered, black neoprene. Includes grip and mounting hard-ware.

Gives Riot Gun Configuration

#692-011-870AQ Rem 870 Vindicator Grip, 2F39P30 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 47.99

#692-011-500AQ Moss 500 Vindicator Grip, 2F39B30 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 47.99

PACHMAYR

VINDICATOR GRIP

5-pak

sho

tg

un

PAGE 212 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

STO

CK

S

Rugged, shock-proof polymer replacement for factory forend upgrades your Remington, Mossberg,

or Winchester pump shotgun with a heavily textured tactical forend for home defense or competition. Deep grooves give a secure purchase for fast, positive racking and enhanced recoil control. Installation requires some disassembly of shotgun, in-cluding barrel, forend, and forend nut. Mossberg model comes with a forend extender. abSPECS: Injection-molded polymer, matte black. 17/8" (4.7cm) diameter. Remington/Winchester – 6" (15.2cm) long, 5.6 oz. (158g) wt. Mossberg – 6¾" (17.1cm) long, 6.1 oz. (173g) wt. Fits Remington 870 - 12 gauge only; Mossberg 500/590/835 - 12 gauge; Winchester 1200/1300 - 12/20 gauge. Mounting hardware and instructions included.

PHOENIX TECHNOLOGY

UNIVERSAL SHOTGUN FORENDRugged One-Piece Forend

For Tactical Upgrade

#100-008-788AQ Remington/Winchester Forend, 3C12Q14 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 14.99

#100-008-789AQ Mossberg Forend, 3C12A14 � � � � � � � � � 14.99

Law Enforcement (LE) and Sport style synthetic forends provide a tougher alternative to factory, wooden parts for hunt-ing or tactical applications. LE forends are shorter than factory length with deep grooves for a positive grip under stressful tac-tical conditions. Sport model resembles the factory length and contours and feature molded-in checkering for a solid grip. abSPECS: Poly-resin, black, matte finish. All models fit 12 ga. only. Rem 870 LE - 7" (17.8cm) long. Moss 500/590 LE - 8" (20.3cm) long. Rem 1100 Sport - 11.5" (29.2cm) long.

SPEEDFEED FORENDS & PARTS

Change Forends To Match Your Shooting Style

#838-150-870AQ Rem 870 LE Forend, 6K23F84� � � � � � � $ 26.99#838-150-500AQ Moss 500/590 LE Forend,

6K28D99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 29.99#838-155-110AQ Rem 1100 Sport Forend, 6K27G31 � � � 31.99

Grip width, angle and backswell all combine to spread recoil over both hands. Finger grooves and the pebble texture give a positive grip.

No alterations to the gun are required. Rear grip includes sling loop. Sold separately with all necessary mounting hardware and instructions. abSPECS: Black, ABS polymer. Forend Grip - Approximately 61/4" (15.9cm) long, 55/8" (14.3cm) high. Rear (Pistol) Grip - Approximately 41/4" (10.8cm) long, 55/8" high.

TACSTAR SHOTGUN TACTICAL GRIPForend & Rear Pistol Grips

For Popular Pumps

STK# FOrEND STK# rEAr FITS#867-100-870AQ #867-101-870AQ Remington 870#867-100-500AQ #867-101-500AQ Mossberg 500#867-100-120AQ #867-101-120AQ Winchester 1200/1300

— Advise # — Tactical Forend, 7F23D40 � � � � � � � � � � � � � $ 25.99

Impact-resistant, Tactical Stock Adapter provides a strong, lightweight coupler to at-tach pistol grips and CAR-15 style butt stocks to the popular, Remington 870 shotgun. 33% fiberglass-reinforced nylon provides supe-

rior strength with minimal weight increase; won’t warp, crack, or shrink in extreme weather conditions. Tight-tolerance, molding process ensures proper fit and virtually eliminates unsightly mold seams. Slight, 7° angle drops the butt stock for an improved sight path with barrel-mounted sights. Allows 10" to 13" length-of-pull adjustment when used with a collapsible, “shorty” stock. abSPECS: Fiberglass-reinforced nylon, matte black. 23/4" (7cm) long, 11/2" (3.8cm) wide, 3" (7.6cm) high. Includes locking ring and grip hardware. 5 oz. (142g) wt. Fits Rem 870, 12 ga.

ARMSTECH, LLC REMINGTON 870

TACTICAL STOCK ADAPTERConverts Your Shotgun To A Tactical Workhorse

#432-000-002AQ Tactical Stock Adapter, 2C29E21 � � � $ 34.54

Tough, synthetic stocks provide secure handling in all weather conditions. Furnished with adapters and spacers for installation on various Mossberg, Remington, Norinco and Winchester pump shotguns. Easy to install, drop-in installa-tion ab

PISTOL GrIP BUTTSTOCK - Full length stock features a slim, finger-groove pistol grip for maximum control. For-ward angle comb prevents recoil from battering your cheek. Solid rubber recoil pad cushions against recoil shock. Includes rear sling swivel stud. Uses factory stock bolt.SPECS: Glass-filled nylon, black. 14" (35.6cm) L.O.P. Fits Moss. 500/Mav-erick 88, Rem. 870, and Win. 1200/1300 shotguns. 12 gauge models only.#019-000-001AQ Pistol Grip Buttstock, 9A36P83 � � � � � $ 43.99

SHOTFOrCE TACTICAL CAr-15 SHOTGUN STOCK - Light-weight, six position stock with a molded pistol grip mounts firmly on your shotgun to provide supe-rior control. Installs easily in minutes with no gunsmithing required. Sling swivel stud and removable rubber buttpad included. Tough, glass-filled nylon polymer stands up to all weather conditions.SPECS: Molded polymer, black. 101/2" (26.6cm) – 141/4" (36.2cm) L.O.P. Fits Moss. 500/590/835, Rem. 870, Norinco 98, Win. 1200/1300. 12 gauge models only.#019-000-013AQ Shotforce Tactical Stock, 9A57N30 � � $ 67.99

PUMP SHOTGUN FOLDING STOCK - Nylon-resin folding stock quickly flips open/closed for maximum ma-neuverability and compactness. Pis-tol grip provides additional control. Latch can be reversed for right- or left- handed shooters. Includes sling swivel.SPECS: Nylon polymer, black. Pistol grip - 23/8" (6cm) wide, 31/2" (9cm) tall, 13/16" (3cm) thick. Approximately 133/4" (35cm) L.O.P. Fits Moss. 500/535/590/835/Maverick 88, Rem. 870, Win.1200/1300. 12 ga. mod-els only.#019-000-010AQ Folding Shotgun Stock, 9A61A40 � � � $ 72.99

HEAT SHIELD - Formed steel with elongated cooling slots protects your hands from burns. Provides a secure, non-slip, grasping surface, plus maximum heat dissipation. Simply slide over barrel and secure with supplied hardware. Black oxide fin-ish matches most shotgun finishes. No gunsmithing required to fit most popular 12 ga. pump guns.SPECS: Steel, black oxide, matte finish. 133/4" (35cm) long.#019-000-004AQ Heat Shield, 9A20H46 � � � � � � � � � � � � � � $ 24.99

SHOTSHELL HOLDEr - Lightweight, polymer shell holder keeps extra ammo handy for fast loading. Provides instant access to five rounds of spare 12 ga. ammo. Carrier attaches to either side of any full length wood or synthetic stock using six screws.SPECS: Elastomeric polymer, black. 5" (12.5cm) long. Installation requires modification to stock.#019-000-005AQ Shotshell Holder, 9A11L59 � � � � � � � � � � $ 13.99

HEAT SHIELD W/GHOST rING SIGHT - Self-centering rear ghost ring with large, .122" I.D. aperture for fast target acquisition. Formed steel with elongated cooling slots protects your hand from burns and provides maximum heat dissipation. Front blade with side guards protects the blade from damage. Easy installation, simply slide over barrel and secure with supplied hardware. Fits 12/16/20 ga. and .410 pump shotguns.SPECS: Shield - Steel, black. 13" (35cm) long. Sights - Polymer, matte black. Aperture - .122" (3.1mm) ID. Fits 12/16/20 ga. and .410 pump shotguns.#019-000-018AQ Heat Shield w/Sights, 9A23M19 � � � � $ 27.99

ADVANCED TECHNOLOGY PUMP SHOTGUN

TACTICAL SHOTGUN SYSTEMImproves Control & Handling Convenience

Drop-in replacement for your 1100/11-87 factory stock has adjustable comb height with left/right positioning to ensure a solid cheekweld for different types of shooting or different shooters. Also provides up to 1" of length-of-pull adjustment to further the custom fit. Recoil-absorbing, 1" thick Limbsaver® synthetic rubber buttpad adds further protection and comfort. Made from lightweight, yet strong, 30% fiberglass-reinforced molded polymer that resists impact, moisture, and surface abrasion. Distinctive silver/black/gray carbon graphite bas-ket weave finish. Molded-in pebble texturing at the pistol grip helps you maintain a secure hold. Includes an ergonomically contoured forend with molded checkering. recoil-reducing Stock features the Ken Rucker “Bump Buster” hydraulic recoil system that significantly reduces felt recoil. abSPECS: Fiberglass-reinforced molded polymer, Carbon Graphite finish, with synthetic rubber recoil pad. Mounting hardware and instructions included.

BILL DAVIS ENTERPRISES REM 1100/11-87

ADJUSTABLE STOCKS

Built-In Recoil-Reduction System Plus Adjustable Comb Height & LOP

100-010-482AQ Rem 1100/11-87 Adj. Stock Set, 5C229A99 � � � � � � � � � � � � � � � � � � � � � � � � � $ 299.99

#100-006-950AQ Recoil-Reducing Adj. Stock Set, 5C399I99 � � � � � � � � � � � � � � � � � � � � � � � � � � 449.99

Drop-in replacement for factory stock lets you adjust the comb height and left/right posi-tion to provide a solid cheekweld for different types of shooting or different shooters. Simply loosen two hex-head screws on the right side of the comb to change height; remove the comb and loosen the two support posts to change left/

right position. Made from lightweight, yet exceptionally strong, 30% fiberglass-reinforced molded polymer that resists impact, moisture, and surface abrasion. Available with a non-reflecting black finish (1100 model) or silver/black/gray carbon graphite basket weave pattern (870 model). Molded-in pebble textur-ing at the pistol grip helps you maintain a secure hold, while a generous, 1" thick recoil-absorbing synthetic rubber recoil pad protects the shoulder. Set includes an ergonomically con-toured forend with molded checkering. abSPECS: Fiberglass-reinforced molded polymer, matte black or Carbon Graphite finish, both with black synthetic rubber recoil pad. Mounting hardware and instructions included.

BILL DAVIS ENTERPRISES REM 870/1100

ADJUSTABLE COMB STOCKS

Carbon Graphite

#100-004-345AQ Rem 870 Adj. Comb Stock Set, Carbon Graphite, 5C142P79 � � � � � � � � $ 199.99

#100-004-329AQ Rem 1100 Adj. Comb Stock Set, Black, 5C149P99 � � � � � � � � � � � � � � � � � � � 199.99

Quickly Change Comb Height & Offset To Fit Any Type Of

Shooting Or Shooter

Unique, synthetic stock features an extension spring and levercam that turns the kick into a gentle push. Provides as much as 50% reduction in recoil. Soft-Start cam provides ad-ditional cushion from recoil; automatically compensates for light and heavy loads with no adjustment or tuning. A soft rub-ber butt pad gives even more recoil cushion. Overmolded grip and forend have comfortable pebble texture surface. Not for use with scopes. abSPECS: Fiberglass impregnated plastic, black, matte finish. 141/8" (35.9cm) length of pull, 11/2" (3.8cm) drop at comb. 1/2" (12.7mm) and 1" (2.5cm) spacers. 11/8" (2.9cm) recoil travel. 11/2 lb. (680 g) weight. 870 fits all Rem. 870 models, Mossberg fits all 500 series and 835.

BLACKHAWK INDUSTRIES

COMPSTOCK™

#100-000-688AQ Rem 870 CompStock, 1A88A18 � � � � � $ 99.99#100-000-689AQ Mossberg CompStock, 1A88B18 � � � � 99.99

Reduces Recoil With Light Or Heavy Loads

Imp a c t - re s i s t a nt , high strength, Zytel stock with solid steel, mount-ing block folds at the hinge to provide com-pact carry and transpor-tation of your 12-gauge, tactical shotgun. Im-proves maneuverability in close quarter, combat zones and withstands

blows that would shatter less durable stock materials. M16-style pistol grip improves muzzle control; diamond-cut checkering molded into the grip ensures a positive hold, wet or dry. In-cludes two, fixed loops for sling or lanyard attachment. Top Fold stock locks into shooting position by depressing a push-button and swinging it downward. Rubber-coated buttplate flips for-ward, out of the way when stock is folded down. Side Fold stock pivots horizontally; folds to the side by pushing it downward to unlock the hinge. Must be used with short, combat forend in-cluded with buttstock. 1" pad helps tame heavy recoil and keeps buttstock planted in your shoulder. Available for Remington 870 and Mossberg 500 and 600. abSPECS: 4140 steel and Zytel, black. Top Fold - 2.1 lb. (1 kg) wt. Side Fold - 1.9 lb. (.86 kg) wt. 13" (33 cm) LOP. Models for Rem 870 and Mossberg 500/600, 12-gauge only.

CHOATE REM 870/MOSSBERG 500 & 600

SHOTGUN FOLDING STOCKSTop & Side Fold Models Adapt To Your Tactical

ApplicationSide fold

#159-000-014AQ Remington 870 Top Fold Stock, 9E87N83� � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 99.99

#159-000-015AQ Remington 870 Side Fold Stock, 9E77P23 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 89.99

#159-000-016AQ Mossberg Top Fold Stock, 9E87Q83� � � � � � � � � � � � � � � � � � � � � � � � � � � � 99.99

#159-000-021AQ Mossberg Side Fold Stock, 9E77C23 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 89.99

Top fold

Model

sho

tg

un

PAGE 213Orders/Tech: 800-741-0015order on the web

brownells.com

STO

CK

S

Adjustable stock with pistol grip improves control and ma-neuverability for fast target acquisition and accurate follow-up shots – perfect for tactical use. Dual spring-loaded recoil-reduction system minimizes felt recoil and reduces muzzle rise, allowing you to stay on target after every shot. Soft rubber LimbSaver® recoil pad further improves recoil protection. Sev-en-position buttstock allows length of pull adjustment from 111/4" to 15" to fit just about any shooter in a variety of shooting situations. Interchangeable inserts let you customize the pistol grip for comfort and maximum control. Stock has sling both swivel stud and slot, plus an integrated ambidextrous single-point sling plate and quick detach sling swivel, for mounting the sling of your choice.SPECS: Molded polymer, black or universal camouflage. 12 gauge only. Fits Mossberg 500/535/590/835 and Maverick 88. Installation instruc-tions included. 31 oz. (879g) wt.

BLACKHAWK® INDUSTRIES MOSSBERG 500/535/590/835

SPECOPS GEN II™ RECOIL REDUCING ADJUSTABLE STOCK SET

#100-008-918AQ Mossberg SpecOps II Stock, Black, 1A95K24 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 104.99

Heavy Duty Recoil Reduction System For Superb Control &

Fast Follow-Up Shots

Folding, pistol-grip stock with built-in recoil-reduction system is designed to pro-vide compact storage and maximum control for fast, accurate shot placement at any range. Weapon can be operated with stock folded—perfect for home defense and CQB situations that require speed and maneuverability in tight spaces like ve-hicles, doorways, and hallways. Folded position leaves plenty of clearance for ghost ring and other rear sight systems up to 17/8" wide. Recoil-reducing mechanism in the pistol grip cuts felt recoil by as much as 65% for fast target reacquisition and more precise follow-up shots with even the hardest-kicking magnum buckshot and slug loads. Steel-wire buttstock with synthetic rubber coating locks securely in both open and closed positions; simply squeeze the rods toward each other to unlock and change position. Swivel stud on the back of the receiver extension provides convenient single-point sling at-tachment. No permanent changes to receiver required; simply remove factory buttstock and attach SpecOps Folder with its captive bolt. For proper clearance of folded stock, shorten the rear of the forend or install a short, combat-style forend like the Hogue® Overmolded, available separately. abSPECS: Polycarbonate grip and rubber-coated steel buttstock, black. 133/4" (35cm) length of pull. Grip – 31/2" (9cm) high, 27/8" (7.3cm) wide, 11/8" (2.9cm) thick at palm swells. Remington fits Remington 870, 12 gauge only. Mossberg fits 12 & 20 gauge Mossberg 500/590/835 and Maverick 88. Do not install on 590DA.

HOGUE OVErMOLDED FOrEND - Rubber-overmolded, shotgun forend eliminates interference problems with SpecOps Folder.SPECS: Polymer, black, rubber-coated finish. Remington fits 12-gauge, Remington 870. Mossberg fits the 500, 590, 835, and Maverick 88, 12 gauge models.#408-000-066AQ Rem. 870 Forend, only, 8K18C77 � � � � $ 20.99#408-000-067AQ Moss. 500 Forend, only, 8K18G77 � � � 20.99

BLACKHAWK INDUSTRIES

KNOXX SPECOPS FOLDER STOCKPowerful Recoil

Reduction, More Control &

Compact Storage For Tactical Shotguns

#100-003-180AQ Rem. SpecOps Stock, 1A102C99 � � � $ 129.99#100-003-179AQ Mossberg SpecOps Stock,

1A102G99 � � � � � � � � � � � � � � � � � � � � � � � � � � 129.99

Fiberglass-filled, plastic stocks stand up to the roughest handling your Remington 870/1100 and Mossberg 500/600 can take, without denting or chipping. Two, half-inch thick spacers that let you choose from a 13", 13-1⁄2", or 14" length of pull. Pistol grip provides a natural hold. Features a swivel stud and a hard rubber, vented, recoil pad. Forends taper slightly for a natural hold; Remington 870 and Mossberg 500/600 Forends are grooved for a positive grip. Remington 1100 Forend is checkered and is similar to the factory forend. Includes sling swivel stud. Stock and Forends sold separately. Available for 12 gauge only. abSPECS: Fiberglass, black matte finish. Unless otherwise specified, compo-nents fit 12 gauge only. Pistol Grip - Approximately 1-1⁄4" (3.2cm) wide, ex-tends 3-1⁄2" (9cm). Stocks - 20 oz. (567g) weight; 14" (36cm) length of pull, adjustable to 13" (33cm) and 13-1⁄2" (34.3cm). 870 Forend- 6.25" (15.8cm) long, 1.75" (4.4cm) diameter, 4 oz. (113g) wt. Available for 12 or 20 gauge. 1100 Forend - 11" (27.9cm) long, 1.825" (4.7cm) diameter, 8 oz. (227g) wt. 500/600 Forend - 7.75" (19.6cm) long, 1.75" diameter, 4 oz. (113g).

NON-ADJUSTABLE 870/1100 STOCK - Includes the same, great toughness and weatherproof features of the adjustable stocks listed above. Features a thinned pistol grip for a natural feel with lighter weight. Vented, hard rub-ber pad protects your shoulder from recoil. Includes fixed sling swivels and studs.SPECS: Fiberglass, black matte finish. Pistol Grip - 7/8" (2.2cm) wide, ex-tends 31/2" (9cm). Stock - 14" (36cm) length of pull. 19 oz. (54 g) weight.#159-100-000AQ 870/1100 Stock, 9E63B36 � � � � � � � � � � � $ 78.99

CHOATE 12 GAUGE SHOTGUN

FIBERGLASS PISTOL-GRIP STOCK

#159-000-002AQ Remington 870 Adj. Length Stock, 9E63G00 � � � � � � � � � � � � � � � � � � � � � � � � � $ 69.99

#159-000-003AQ Remington 1100 Adj. Length Stock, 9E63N00 � � � � � � � � � � � � � � � � � � 69.99

#159-100-500AQ Mossberg 500/600 Adj. Length Stock, 9E63B00 � � � � � � � � � � � � � � � � � � 69.99

#159-101-870AQ Rem. 870 Forend, 9E16N50 � � � � � � � 18.99#159-101-500AQ Moss. 500/600 Forend, 9E16P50 � � 18.99#159-101-110AQ Rem. 1100 Forend, 9E30G00 � � � � � � 33.99

Adjustable Length Of Pull For A Custom Fit;

Weatherproof Choice Of Law Enforcement Agencies

Easy-to-install hydraulic recoil buffer tames recoil while al-lowing for the attachment of AR-15/M4 style collapsible stocks on tactical shotguns. The internal hydraulic buffer softens recoil by absorbing the energy rather than spreading it out over time like spring only buffers. Made of lightweight, rugged aluminum, Mil-Spec buffer features five positions for a wide range of adjustments. Requires use of an AR-15 shotgun stock adapter, sold separately. abSPECS: Aluminum, anodized, matte black finish. 8.12" (20.6cm) long. 1.14" (2.9cm) dia. 13.4 oz. (379.9g) wt. Fits AR-15/M16 shotgun stock adapters. Uses standard AR-15/M16 castle nut and end plate.

CROSSHAIR

SHOTGUN RECOIL REDUCING STOCK ADAPTER

Out Performs Spring Only

Buffers

#100-015-232AQ Recoil Reducing Adapter, 8H132Q39 � � � � � � � � � � � � � � � � � � � � � � � � $ 149.99

Fiberglass-reinforced, polymer stock and forend provide added durability and are overmolded with rubber for a sure grip. Rubber is pebble-textured in the gripping areas. Includes recoil-cushioning buttpad and sling swivel stud. Available in factory length-of-pull or in ShortShot that has 12" length-of-pull for use with body armor or for smaller shooters. Sets in-cludes stock and forend. Sets and individual components fit 12 gauge only.SPECS: Polymer w/overmolded rubber, black. Stock sets and compo-nents fit 12 gauge only. ShortShot stocks have a 12" L.O.P. Mossberg Forend Adapter Nut required for Mossberg 500/835 with 63/4" forend tubes.

HOGUE

OVERMOLDED SHOTGUN STOCKS

#408-000-044AQ Rem. 870 Stock Set, 8K49M99 � � � � � � $ 52.86#408-000-059AQ Moss. 500 Stock Set, 8K49I99 � � � � � � � 55.99#408-000-060AQ Win. 1300 Stock Set, 8K48H84 � � � � � � 56.99#408-000-055AQ Rem. 870 ShortShot Stock Set,

8K55G82 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 59.99#408-000-056AQ Moss. 500 ShortShot Stock Set,

8K55A82 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 65.99#408-000-057AQ Win. 1300 ShortShot Stock Set,

8K55K82 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 59.99#408-000-058AQ Rem. 870 Stock, only, 8K42I00 � � � � � � 46.99#408-000-061AQ Moss. 500 Stock, only, 8K41H86 � � � � 49.99#408-000-063AQ Rem. 870 ShortShot Stock, only,

8K49G00 � � � � � � � � � � � � � � � � � � � � � � � � � � � 55.99#408-000-064AQ Moss. 500 ShortShot Stock, only,

8K49H00 � � � � � � � � � � � � � � � � � � � � � � � � � � � 55.99#408-000-066AQ Rem. 870 Forend, only, 8K18C77 � � � � 20.99#408-000-067AQ Moss. 500 Forend, only, 8K18G77 � � � 20.99#408-000-069AQ Mossberg Forend Adapter Nut,

8K9I99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12.99

Durable Stock With Outstanding Grip Characteristics

Drop-in, fold-ing butt stock pro-vides enhanced performance and versatility for Remington and Mossberg combat shotguns. Streamlined, compact butt-stock can be adjusted to the operator’s desired length of pull. Stock features a patented recoil compensating system for un-paralleled recoil reduction. The rubber buttpad, with non-slip texture, can be adjusted to five different positions and covers a battery storage compartment in the base. Folding stock is held to the side by spring tension, ensuring a rigid, rattle free lockup. To deploy, simply pull the stock and a robust claw locks it into position. Hinge can be switched so the stock folds to either the right or left. The textured ergonomic pistol grip is slightly angled to promote a natural fighting stance and aid in recoil resistance.SPECS: Reinforced polymer composite with steel components, black. M4 style aluminum buffer tube, black. 12.4" (31.4 cm) long, 13.9" (35.3 cm) extended, 1.9" (4.9 cm) wide, 5.6" (14.2 cm) high. 25.6 oz. (726 gr) wt.

THE MAKO GROUP REM 870 & MOSS 500/590

RECOIL REDUCING FOLDING STOCKSGives Your

Tactical Shotgun More Versatility

#100-016-526AQ Recoil Reducing Folding Stock, Moss 500/590, 2B219L43 � � � � � � � � � � �$ 253.00

#100-016-527AQ Recoil Reducing Folding Stock, Rem 870, 2B219G43 � � � � � � � � � � � � � � � 253.00

These kits are built around the Mesa Tactical Urbino buttstock to transform your Remington 870 into a ver-satile, fast-handling tactical shotgun. Urbino Upgrade Kit includes the stock, a 6-round receiver mount shell holder, replacement magazine cap with sling loop, and a sling loop for the Urbino stock. Ultimate Sureshell Kit adds to the Urbino tactical stock a Sureshell 6-round shotshell carrier, 20" Pica-tinny accessory top rail, and a receiver mount attachment for single-point sling. ab

MESA TACTICAL UPGRADE KITS

Ultimate Sureshell Kit

#100-011-407AQ Urbino Stock Upgrade Package, 5A172P00 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 189.99

#100-008-829AQ Ultimate Sureshell Urbino Stock Kit, 5A336H77 � � � � � � � � � � � � � � � � � � � � � 369.99

Comfort & Control Upgrades For Your

Remington 870

Minimum-drop, straight-line buttstock enhances recoil control. Pistol grip provides increased leverage to hold the muzzle down. Made from durable, poly-resin material for years of service life. Includes energy-absorbing, molded-rubber re-coil pad. TAC III design incorporates additional shell storage in the buttstock. TAC IV is solid; TAC IV-S model is sized for the smaller shooter or those wearing body armor. All Remington 870 and Mossberg 500 models include the short, Law Enforce-ment (LE) forend and Mossberg models ONLY fit guns with a 73/4" action slide. Benelli fits Super 90, includes buttstock only, no forend. abSPECS: Poly-resin, black, matte finish. Length of Pull - TAC III/ TAC IV, 14" (35cm), TAC IV-S, 13" (33cm). Includes forearm; sold as a set only. Fits 12 gauge only. Win. 1300 fits Model 1200/1300.

SWAT rECOIL PAD - Fits TAC IV-S and Youth Sport stocks. Hard, polycarbonate core with soft, shock-absorbing synthetic rubber exterior to tame the kick of recoil.SPECS: Rubber and polycarbonate, black. 7/8" (22mm) thick.#838-000-013AQ IV-S Swat Recoil Pad,

6K11G79 � � � � � � � � � � � � � � � � � � � � � � � $ 12.99

SPEEDFEED

PISTOL GRIP SHOTGUN STOCK

Positive Grip, Better Recoil Control

LE Forend

STOCK # FITS MODEL PrICE#838-000-012AQ Benelli S 90 TAC IV-S 6K76A59 $ 89.99#838-103-255AQ Moss. 500 TAC III, LE 6K95K34 $ 109.99#838-103-250AQ Rem. 870 TAC III, LE 6K95K34 $ 109.99#838-103-254AQ Rem. 1100 TAC III 6K95A34 $ 109.99#838-103-252AQ Rem. 11-87 TAC III 6K95Q34 $ 109.99#838-104-260AQ Rem. 870 TAC IV, LE 6K85A79 $ 99.99#838-104-264AQ Rem. 1100 TAC IV 6K85L79 $ 99.99#838-104-280AQ Rem. 870 TAC IV-S LE 6K91D89 $ 109.99#838-104-282AQ Rem. 11-87 TAC IV-S 6K91F89 $ 109.99

sho

tg

un

PAGE 214 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

STO

CK

S

Bolt-on replace-ment stock gives your shotgun the control and adaptability of a collapsible M4 carbine stock. Telescoping, five position butt-stock allows fast length-of-pull adjustment to adapt to body armor and heavy tactical clothing. Aluminum receiver adapter bolts to rear of receiver with included mounting hardware and requires no permanent alterations to your gun. Accepts the included M4 SOPMOD buttstock or any aftermarket stock that fits a mil-spec (1.14" O.D.) buffer tube. Hogue overmolded rubber pistol grip with palm swells and finger grooves bolts sol-idly to the receiver adapter to reduce recoil shock and give the shooter better control. Includes one push-button sling swivel that fits sockets on either side of the receiver adapter. Models for remington 870 and Mossberg 500, 12 gauge only. Basic LEO (Law Enforcement) model positions the buttstock low enough to allow use of the original shotgun bead or iron sights. Four-position stock offers length of pull adjust from 101/2" to 131/2". recoil reducing model combines the low tube position and M4 buttstock with an Enidine hydraulic energy absorber to reduce felt recoil by as much as 70%. Gives you oustanding control to ensure fast, accurate follow-up shots. L.O.P. adjusts from 111/2" to 141/2" in five, pre-set locking positions. Stock Adapters also sold separately; accepts standard AR-15 pistol grips and M4-type carbine receiver extensions. ab

MESA TACTICAL REMINGTON 870

TELESCOPING STOCK CONVERSION KITS

Gives A Tactical Shotgun M4 Carbine

Handling; Optional Recoil

Reduction System

#100-005-558AQ Rem 870 LEO Stock Kit, 5A155I93� � � � � � � � � � � � � � � � � � � � � � � � � � � $ 174.99

100-011-372AQ Moss 500 LEO Stock Kit, 5A160J14 � � � � � � � � � � � � � � � � � � � � � � � � � � 179.99

#100-003-175AQ Rem 870 Recoil-Reducing Stock Kit, 5A248F64 � � � � � � � � � � � � � � � � � � � � � 272.99

100-011-373AQ Moss 500 Recoil-Reducing Stock Kit, 5A252H86 � � � � � � � � � � � � � � � � � � � � � 281.99

100-011-374AQ Rem 870 Stock Adapter, Only, 5A63H21 � � � � � � � � � � � � � � � � � � � � � � � � � � � 69.99

100-011-375AQ Moss 500 Stock Adapter, Only, 5A67B43 � � � � � � � � � � � � � � � � � � � � � � � � � � � 74.99

Complete furniture set replaces factory buttstock and fore-arm to convert 12 gauge 870 into a tactical/3-gun competi-tion shotgun with the feel and controllability of an AR-15/M4 carbine. The M4-type 6-position collapsible buttstock lets you set a comfortable length of pull and make quick adjustments to accommodate body armor or tactical clothing. Removable rubber recoil pad helps tame felt recoil. Pistol grip has ergo-nomic finger grooves to ensure a secure grasp. Side and bottom rails on forend accept the included vertical grip and a variety of other accessories. Two removable shell holders attach to stock and each hold 3 spare shells. Easy installation, no permanent modifications required. abSPECS: Reinforced injection-molded polymer, black. Buttstock - 101/4" (26cm) OAL collapsed with recoil pad. 14" (35.6cm) OAL fully extended with recoil pad. Recoil pad – rubber, black. 1" (2.5cm) thick. Forend – 61/4" (15cm) long, 21/4" (5.7cm) wide, 113/16" (4.6cm) high. Vertical Grip – 41/2" (11.4cm) long x 13/16" (3cm) OD. Mounting hardware included. Fits 12 gauge Remington 870 only.

PRO MAG REM 870

ADJUSTABLE STOCK SET

Converts A Sporter To Tactical/3-Gun Competition Configuration

#687-000-047AQ Rem 870 Adj. Stock Set, 7H66Q14 $ 74.99

Pistol grip stock of rugged, fiberglass-re-inforced nylon polymer has a short 121/2" (31.7cm)

length of pull that makes it easy to shoulder and maneuver when you’re wearing body armor. The removable, five-posi-tion cheek riser helps you position your head for best align-ment with an optic while maintaining a solid cheekweld. Pistol grip has ample contact surface with deep horizontal grooves for a secure grasp and excellent weapon control. Shock-ab-sorbing padding on the backstrap helps protect your hand from recoil, while the Limbsaver® recoil pad helps reduce felt recoil. Includes a 11/2" slot rear sling loop, plus a stud on the underside for a QD sling swivel. abSPECS: Injection-molded, glass-filled nylon, black. 121/2" (31.7cm) length of pull. 21/8" (5.4cm) wide, 71/2" (19cm) tall with cheek riser at highest eleva-tion. 1 lb., 10 oz. (748g) wt. Mounting hardware and installation instruc-tions included. Benelli M1/M2 also fits M3, Super Nova, and Super Black Eagle; will not fit SBE II and some older M1 variants. Benelli M4/M1014 includes forearm.

MESA TACTICAL

URBINO TACTICAL SHOTGUN STOCK

Improves Comfort & Maneuverability With Body Armor

#100-006-706AQ Benelli M4/M1014 Urbino Stock, 5A150J00 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 157.99

100-009-246AQ Benelli M1/M2 5A154G35 � � � � � � � � � � 157.99#100-006-707AQ Remington 870 Urbino Stock,

5A131M58 � � � � � � � � � � � � � � � � � � � � � � � � � 144.99

Classic walnut provides a close match to original factory stocks. Quality wood, has a straight grain pattern. 95% inletted for easy fitting to your action. Ready for final sanding, stain and finish. abSPECS: Walnut, straight grain, no figure. Accepts original hardware.Sav-age 94 forend comes relieved for .410 bore; can be opened up for 12 and 20 gauge.

WOOD PLUS

REPLACEMENT GRADE STOCK

STOCK # FITS PrICEBUTTSTOCK ONLY

#984-100-011AQ Remington 11 4H45J72 $ 53.99#984-100-311AQ Savage 311 4H46L43 $ 54.99#984-100-494AQ Savage 94 4H45P72 $ 53.99#984-100-012AQ Winchester 12 4H45H72 $ 53.99#984-100-097AQ Winchester 97 4H45N72 $ 53.99

BUTTSTOCK AND FOREND SET#984-110-494AQ Savage 94 (.410 forend) 4H63I58 $ 74.99

Real Walnut; Original Contours

ASK ABOUT OVERNIGHT DELIVERY!

SGA STOCK - User-configurable stock offers improved ergonomics, including a spacer system that lets you tailor the length of pull to the individual shooter in 1/2" increments from 121/2" to 141/2". Ergonomically enhanced grip area is similar to a pistol grip and a recoil-absorbing buttpad delivers excellent control and pointability. Accepts optional cheek ris-ers (sold below) to change the comb height. Both sides have a slot for threading on a 11/4" wide sling. Available alone or in a Set that includes the MOE® Forend listed below. SPECS: Reinforced, hard-molded polymer, Black, Dark Earth, Stealth Gray, or Orange. Rem fits Remington 870, 12 gauge only. Moss fits 12 gauge 500, 590 and 590A1. Mounting hardware and instructions in-cluded.#100-009-619AQ Rem SGA Stock, Black, 3K91Q89 � � � $ 104.45#100-009-620AQ Rem SGA Stock, Dark Earth,

3K91P89 � � � � � � � � � � � � � � � � � � � � � � � � � � � 104.45 100-015-242AQ Rem SGA Stock, Stealth Gray,

3K91J89 � � � � � � � � � � � � � � � � � � � � � � � � � � � 104.45#100-009-621AQ Rem SGA Stock, Orange, 3K91H89 � 104.45#100-011-605AQ Moss SGA Stock, Black, 3K91N89 � � 104.45#100-011-606AQ Moss SGA Stock, Dark Earth,

3K91E89 � � � � � � � � � � � � � � � � � � � � � � � � � � � 104.45 100-015-243AQ Moss SGA Stock, Stealth Gray,

3K91G89 � � � � � � � � � � � � � � � � � � � � � � � � � � � 104.45#100-011-607AQ Moss SGA Stock, Orange, 3K91B89 104.45#100-011-222AQ Rem SGA Stock/MOE Forend,

Black, 3K112M88 � � � � � � � � � � � � � � � � � � � 129.99#100-011-223AQ Rem SGA Stock/MOE Forend,

Dark Earth, 3K112B88 � � � � � � � � � � � � � � 129.99 100-015-246AQ Rem SGA Stock/MOE Forend,

Stealth Gray, 3K112E88 � � � � � � � � � � � � � 129.99#100-011-224AQ Rem SGA Stock/MOE Forend,

Orange, 3K112P88 � � � � � � � � � � � � � � � � � 129.99#100-011-635AQ Moss SGA Stock/MOE Forend,

Black, 3K112H88 � � � � � � � � � � � � � � � � � � � 129.99#100-011-636AQ Moss SGA Stock/MOE Forend,

Dark Earth, 3K112Q88 � � � � � � � � � � � � � � 129.99 100-015-247AQ Moss SGA Stock/MOE Forend,

Stealth Gray, 3K112D88 � � � � � � � � � � � � 129.99#100-011-637AQ Moss SGA Stock/MOE Forend,

Orange, 3K112Q88 � � � � � � � � � � � � � � � � � 129.99

SGA CHEEK rISEr KITS - Easy to install modu-lar risers fit on the comb of the SGA Stock to change the comb height for a better cheek weld and to position the shooter’s head at the proper height for various sights and optics. Low kit in-cludes two inserts that raise the comb 1/4" or 1/2" above the standard SGA comb. High kit’s two inserts raise the comb 1/2" or 3/4" above the standard comb. SPECS: Reinforced, hard-molded polymer, Black or Dark Earth. Recom-mendations: low-profile bead sights, ghost rings, or similar – no riser or 1/4"; red dot, standard holographic, or mini-red dot – 1/4" or 1/2"; magnified optic – 1/2" or 3/4".#100-009-610AQ Low SGA Cheek Riser Kit, Black,

3K14P35 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 15.15#100-009-611AQ Low SGA Cheek Riser Kit, Dark

Earth, 3K14J35 � � � � � � � � � � � � � � � � � � � � � � 15.15#100-009-607AQ High SGA Cheek Riser Kit, Black,

3K13P33 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15.15#100-009-608AQ High SGA Cheek Riser Kit, Dark

Earth, 3K13N33 � � � � � � � � � � � � � � � � � � � � � 15.15

SGA rECOIL PAD ADAPTEr - Lets you replace the standard SGA recoil pad with a Remington fac-tory or aftermarket pad for even more comfort and versatility. SPECS: Reinforced, hard-molded polymer, Black. Mounting hardware and instructions included.#100-009-579AQ SGA Recoil Pad Adapter, 3K8H95 � � � � $ 9.45

SLING MOUNT KIT – TYPE 1 - Steel sling swivel mount allows slings equipped with pushbut-ton QD swivels to attach to the SGA shotgun stock. Easy-to-install because it fastens se-curely to mounting points already molded into both sides of the stock. SPECS: Heavy-duty phosphate steel, Black. Fits SGA Remington 870 and Mossberg 500/590/590A1 shotgun stocks. Also fits Magpul MOE AR-15 stock. Mounting hardware included. Swivels not included.#100-010-975AQ Sling Mount Kit/Type 1, 3K11F89 � � � $ 14.99

SGA SLING MOUNT - Installs between the receiver and the SGA Stock to provide a secure attachment point for clip-on sling systems, including HK-style, MASH hook, Magpul MS3® Paraclip™, and others. May be installed with the loop on left or right side of receiver. SPECS: Steel, with Melonite® coating for strength and wear-resistance, matte black. Compatible with SGA Stocks for Remington 870 and Moss-berg 500/590/590A1.#100-009-581AQ Remington SGA Sling Mount,

3K16M89 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 18.99#100-011-573AQ Mossberg SGA Sling Mount,

3K16H89 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18.99

MOE FOrEND - Drop-in replacement forend extends the comfort and en-hanced control of Magpul’s proven AR-15/M16 MOE forend to the 870 and 500/590/590A1 platforms. Offers extra length, plus front and rear hand stops for easier cycling. Ac-cepts all add-on accessories for the MOE Forend, including the MVG® vertical grip and the Scout Mount (sold below). SPECS: Reinforced, hard-molded polymer, Black, Dark Earth, Stealth Gray, or Orange. Rem fits 12 gauge Remington 870. Not compatible with the 870 Super Mag. Moss fits 12 gauge Mossberg 500/590/590A1 with 73/4" action tube assemblies. May require additional parts and gunsmithing for use with Mossberg Maverick, some 500 models, or as a replacement for Mossberg tri-rails. Not compatible with Mossberg heat shield. Mount-ing hardware included.#100-009-601AQ Rem MOE Forend, Black, 3K25I03 � $ 28.45#100-009-602AQ Rem MOE Forend, Dark Earth,

3K25L03 � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45 100-015-244AQ Rem MOE Forend, Stealth Gray,

3K25M03 � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45#100-009-603AQ Rem MOE Forend, Orange,

3K25P03 � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45#100-011-609AQ Moss MOE Forend, Black, 3K26B95 28.45#100-011-610AQ Moss MOE Forend, Dark Earth,

3K26K95 � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45 100-015-245AQ Moss MOE Forend, Stealth Gray,

3K26A95 � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45#100-011-611AQ Moss MOE Forend, Orange,

3K24H17 � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.45

MOE SCOUT MOUNT - Clamps to the side slots of the MOE Forend to enable installation of a Surefire® Scout Light® or other Picatinny-mountable light. Posi-tions light in the 11 o’clock position (left side) on the forend but as low as possible for easy access and to prevent altering weapon handling char-acteristics. SPECS: Reinforced, hard-molded polymer, Black. Mounting hardware included.#100-009-291AQ MOE Scout Mount 3K7I39 � � � � � � � � � � � $ 9.99

Innovative, integrated accessory system lets you apply the “Magpul Method” to make the tried-and-true 12 gauge 870 and Mossberg pump actions into state-of-the-art tactical shotguns exactly fitted to your mission requirements. Major compo-nents are made from the same tough, hard polymer Magpul uses for their AR-15 stocks to ensure superb durability under harsh conditions. ab

MAGPUL REM 870/MOSSBERG 500 SERIES

SGA™ STOCK & ACCESSORIESNew Versatility For The World’s Most Popular Shotguns

Items Model Items

sho

tg

un

PAGE 215Orders/Tech: 800-741-0015order on the web

brownells.com

STO

CK

S

Weather-resistant, synthetic, thumbhole de-sign keeps five, 12 gauge shells (23/4", 3" or 31/2") handy, right in the buttstock. Grip area features matte texturing for enhanced grip to control recoil and muzzle climb. Length of pull can be adjusted from 131/2" to 141/4".Comes with adjusting spacers, plus longer screws and a replacement mounting bolt. Includes ventilated rubber butt pad and sling swivel stud. abSPECS: Polypropylene, black. 22.5 oz. (637 g).

Carry Extra Shells For Rapid Reloads

#159-000-001AQ Mark-6 Stock, 9E67J50 � � � � � � � � � � � � � $ 79.00

CHOATE REMINGTON 870

MARK-6 STOCK

Synthetic stocks made from thermo-set plastic give long lasting durability and strength. Resin impregnated mate-rial, bonded to long-structured fiberglass strands make these stocks lightweight but completely stable, even in extreme hot or cold weather. They can’t warp, crack, or check and ruin your hunt. Extra-thick, open cushion, field-style pad helps soak up recoil. Standard-Length Stock Sets available for model 870 only. Includes checkered, sport forend. abSPECS: Resin/fiberglass impegnated molded polymer, black. Factory L.O.P. and dimensions. Drilled for rear swivel stud. 1 lb. 8 oz. (640 g) wt. *Note: 20 ga. guns with serial numbers ending in “K” or “U” are small frame and require 20 ga. stock set, those with serial numbers ending in “X” or “N” require a 12 ga. stock set.

rEDUCED LENGTH STOCKS - Same features as the standard-length stocks with 1" shorter length-of-pull than factory measurement to better fit smaller-framed shooters and law enforcement personnel wearing body armor. Set includes checkered sport forend, except 870-L includes shorter, ribbed forend. Stock Only fits 870, 1100, and 11-87 models.SPECS: Resin/fiberglass impegnated molded polymer, black. 1" (2.5cm) shorter than factory L.O.P. Drilled for rear swivel stud. 1 lb. 3 oz. (500 g) wt. All sets except 870-L include checkered sport forend, 870-L includes shorter ribbed forend. *Note: 20 ga. guns with serial numbers ending in “K” or “U” are small frame and require 20 ga. stock set, those with serial numbers ending in “X” or “N” require a 12 ga. stock set.

REDUCED LENGTH STOCK SETS

STOCK # MODEL GAUGE PrICE#838-000-009AQ Rem. 870-L 12 6K85M79 $ 99.99#838-320-870AQ Rem. 870 20 6K91A89 $ 109.99#838-320-110AQ Rem. 1100 20 6K91P89 $ 109.99

#838-000-014AQ Reduced-Length Stock, only, 6K76E51 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 89.99

SPEEDFEED REMINGTON

SYNTHETIC SHOTGUN STOCK

Unbreakable, Weather-Proof Replacement Stocks Match Factory Dimensions

Sport Forend

#838-300-870AQ Standard-Length Rem 870 Stock, 12 ga., 6K76E59 � � � � � � � � � � � � � � � � � � � � � $ 89.99

#838-300-872AQ Standard-Length Rem 870 Stock, 20 ga., 6K76K59 � � � � � � � � � � � � � � � � � � � � 89.99

870-L ForendDurable, fiberglass-reinforced, synthetic stock-and-

forend set perfectly fits your shotgun no matter the weather. Matches factory specs for easy, drop on installation. Includes a fitted, rubber, recoil pad stamped with the Remington logo. Available in 12 gauge only.

MOSSY OAK BrEAK-UP CAMO STOCK SET - Strong, synthetic, camouflage stock-and-forend set resists cracking and split-ting. Mossy Oak Break-Up camouflage conceals your gun dur-ing the hunt. Available in 1100/11-87 and 870.SPECS: Synthetic materials, Mossy Oak Break-Up finish. 1100/11-87 – forend; approximately 115/8" (30cm) long, 2" (5.1cm) high, 13/4" (4.4cm) wide. Buttstock; factory length of pull. 131/2" (34.3cm) long (with recoil pad), 5" (13cm) high (at recoil pad), 11/2" (4cm) wide. Fits all 11-87s; only fits 1100s built after 1986.#767-000-813AQ 1100/11-87 Stock, Mossy Oak,

8F67M50 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 74.99#767-000-815AQ 870 Stock, Mossy Oak, 8F67F50 � � � � � 74.99

MODEL 870 YOUTH STOCK SET - Identical to standard Reming-ton factory stocks except it’s one-inch shorter to accommodate small shooters or those wearing body armor. Available in non-glare, matte black.SPECS: Synthetic material, black finish. Forend; 9" (23cm) long , 13/4" (4.5cm) high, 13/4" (4.5cm) wide. Buttstock; 13" (33cm) length of pull. 121/4" (31cm) long (with recoil pad), 43/4" high (at recoil pad), 11/2" (4cm) wide.#767-000-812AQ 870 Youth Stock, Black, 8F78M00 � � � $ 84.99

REMINGTON 1100/11-87/870

12 GAUGE SYNTHETIC STOCK SETS

Accurate & Weather Proof; Factory Fit Matches Your Action

The same tough, durable, synthetic stocks that the Rem-ington factory uses on their all-weather, Police, and home defense shotguns. Injection molded from fiberglass-filled, thermoplastic material that’s lightweight and stands up to all extreme weather conditions. Sport is a classic stock design built for comfort. Includes molded-in checkering on the wrist and forend for an improved gripping surface. Neoprene rubber recoil pad helps reduce felt recoil for better follow-up shots. Includes rear sling swivel stud. Police has the same great fea-tures as Sport model, but has a shorter, ribbed forend that pro-vides plenty of room for receiver mounted shell carriers and upfront accessories. Drilled for a rear swivel stud (not included). ShurShot™ has an extra-large thumbhole, plus both left- and right-side palm swells and cheek rests for comfortable ambi-dextrous use. Raised comb provides perfect eye alignment with scopes or iron sights. Advanced Supercell™ recoil pad sets a new standard in recoil reduction with an amazing 54% less felt recoil than an autoloader with standard factory pad. Helps pre-vent flinching for quick, accurate follow up shots, and ensures all day shooting comfort. Molded-in texture on the wrist and forend allows a non-slip grip. Includes molded-in rear sling swivel stud. Models available for Remington 870 and 11-87, both 12 gauge only. abSPECS: Nylon plastic, as-molded finish. Sport/Police - Available in Black only. Factory drop at comb and length of pull. Includes buttstock, forend & rear sling swivel stud. Police stock does not include sling swivel stud. 1 lb. 5 oz. (595g) wt. ShurShot - Available in Black, Mossy Oak Obsession® (870), or Realtree Hardwood APF® (11-87) camo pattern. Factory length of pull. Includes buttstock, forend, and rear sling swivel stud. 1 lb. 6 oz. (624g). Models for Rem 870 and 11-87, both 12 gauge only.

REMINGTON 870//11-87

SYNTHETIC SHOTGUN STOCKSport

#768-186-140AQ Rem 870 Sport Stock, Black, 8F67J50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 74.99

#768-186-100AQ Rem 1100/11-87 Sport Stock, Black, 8F67D50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 74.99

#768-186-150AQ Rem 870 Police Stock, Black, 8F110K02 � � � � � � � � � � � � � � � � � � � � � � � � � � � 121.99

#767-000-921AQ Rem 870 ShurShot Stock, Black, 8F48K00 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 54.99

#768-000-017AQ Rem 870 ShurShot Stock, Mossy Oak, 8F76J50 � � � � � � � � � � � � � � � � � � � � � � � 84.99

#767-000-922AQ Rem 11-87 ShurShot Stock, Black, 8F76N50 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 84.99

Police

Genuine Factory Replacement Stocks

Are All-Weather Tough

ShurShot Mossy Oak

ShurShot

Highly visible International orange designates training guns for law enforcement; adds an extra amount of visibility for hunters. Full dimensioned, includes hard rubber recoil pad. Tenite® and fiberglass stock/forend set duplicates weight and balance of factory wood stock. Resists chips, dents and dings, won’t shrink or warp due to tough weather conditions. Peb-ble-grained wrist and short, deeply grooved law enforcement forend for non-slip grip. Available as unmarked Orange or with Less Lethal marked on each side of buttstock. abSPECS: Tenite, fiberglass composite, international orange. Duplicate fac-tory length of pull. 1.6 lb. (720 g) wt. Fits 12 ga. only.

SPEEDFEED REMINGTON 870

INTERNATIONAL ORANGE STOCK

#838-000-007AQ Rem 870 Orange Stock, 6K84L24 � � � $ 99.99#838-000-008AQ Rem 870 Less Lethal Orange Stock,

6K84F24 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 99.99

Quick Identification For Safety & Training

Classic, American Walnut stocks are sanded and given a three-coat, Danish oil finish to provide excellent weather re-sistance and durability. Quality, straight-grained wood looks sharp and is easy to touch up if the stock is nicked or dinged. Includes plastic buttplate. 95% inletted and ready to install; only requires minor fitting. abSPECS: Walnut, straight grain, no figure. Accepts original hardware. Matches factory length of pull; Youth models are shorter. Browning A-5 forend fits 12 ga., 5-shot. Remington 11 forend is 12 ga. only; drilled to accept factory detent. Savage 94 forend comes relieved for .410 bore; can be opened up for 12 and 20 gauge.

WOOD PLUS

PRE-FINISHED REPLACEMENT SHOTGUN STOCKS

Provides A Factory Quality Fit With Hardly Any Work; Matches The Original Contour Of The Factory Stock

STOCK # FITS PrICEBUTTSTOCK ONLY

#984-000-036AQ Browning A-5, 12 Ga. 4H64D29 $ 74.99#984-000-055AQ Mossberg 500 12 Ga. 4H64G29 $ 74.99#984-000-056AQ Mossberg 500 Youth 12 Ga. 4H64C29 $ 74.99#984-000-057AQ Mossberg 500 20 Ga. 4H64B29 $ 74.99#984-000-053AQ Rem. 1100/1187 20 Ga. 4H64B29 $ 74.99#984-000-054AQ Rem. 1100/1187 Youth 20 Ga. 4H64I29 $ 74.99#984-000-007AQ Remington 11, 12 Ga. 4H61P43 $ 71.99#984-000-045AQ Remington 870, 12 Ga. 4H64G29 $ 74.99#984-000-046AQ Rem. 1100/1187, 12 Ga. 4H64M29 $ 74.99#984-000-008AQ Savage 311 4H62F15 $ 72.99#984-000-010AQ Savage 94 4H60L00 $ 69.99#984-000-011AQ Winchester Model 12, 12 Ga. 4H60L00 $ 69.99#984-000-066AQ Winchester 12,20 Ga. 4H60D00 $ 69.99#984-000-027AQ Winchester 37 4H62L86 $ 73.99#984-000-016AQ Winchester 97 4H60G00 $ 69.99

FOREND ONLY#984-000-037AQ Browning A-5, 12 Ga. 4H50F72 $ 59.99#984-000-039AQ Remington 11, 12 Ga. 4H46P43 $ 54.99

BUTTSTOCK/FOREND SET#984-000-029AQ Browning A-5, 12 Ga. 4H105F72 $ 123.99#984-000-030AQ Savage 24 4H97G86 $ 114.99#984-000-031AQ Savage 311 4H97G86 $ 114.99#984-000-017AQ Savage 94, .410 forend 4H90Q00 $ 104.99#984-000-018AQ Remington 11, 12 Ga. 4H105C00 $ 122.99

The convenience and rugged durability of synthetic for shotguns equipped with scopes and rifle sights. Monte Carlo cheekpiece raises the line of sight for faster, easier, more com-fortable sighting. Perfect for slug guns. abSPECS: 12 ga. only. Black, as-molded finish. Raises comb height approxi-mately 3/4" (19mm); length of pull same as factory. Includes rubber recoil pad; molded-in checkering; drilled for rear swivel stud. 1 lb. 10 oz. (700 g) wt. Sold as a set only.

SPEEDFEED REM 1100

MONTE CARLO SYNTHETIC STOCK

#838-301-110AQ 1100 Synthetic Stock Set, 6K84M24� �$ 99.99

Pre-Fit Stock With Raised Cheekpiece For Scoped Shotgun

Tough, black, Tenite and fiberglass Stock/Forend Set won’t shrink, swell or warp due to tough weather conditions. Resists chips, dents and dings, too. Designed for law enforcement . . . perfect for sportsmen. Full dimensioned, includes hard rubber recoil pad. Speedfeed I (SFI) buttstock has molded-in tubes to hold 4 extra rounds. Speedfeed II (SFII) buttstock is solid; du-plicates weight and balance of factory wood stock. Both have matte, flat-black finish. Pebble-grained wrist and short, deeply grooved law enforcement (LE) forend for non-slip grip. abSPECS: Tenite, fiberglass composite, black. All models duplicate factory length-of-pull. 1.6 lb. (720 g) wt. Fits 12 ga. only.

SPEEDFEED

“SPEEDFEED” STOCK

#838-200-870AQ Speedfeed II, 6K52P01 � � � � � � � � � � � � � � $ 59.99

STK# SFI STK# SFII FITS#838-100-501AQ NA Mossberg 500/590#838-100-870AQ #838-200-870AQ Rem. 870#838-100-110AQ NA Rem. 1100

— Advise # — Speedfeed I, 6K85K79 � � � � � � � � � � � � � � � � � $ 99.99

Tenite® & Fiberglass For Stability With Built-In

Shell Storage

sho

tg

un

PAGE 216 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

CO

MP

ET

ITIO

N G

EA

rST

OC

KS

Synthetic stock and forearm fit just like the factory original to keep these single shots shooting. abSPECS: Black polypropylene. Weighs 1 lb. 3 oz. (526 g). Fits H&R/ N.E.F. 12, 20, 28, .410 ga., and all rifles (Topper, etc.)#159-190-108AQ H&R Synthetic Stock, 9E30J00 � � � $ 33.99#159-190-204AQ H&R Synthetic Forend, 9E13J50 � � 16.00

A Replacement Stock That Never Wears Out

CHOATE H&R SYNTHETIC STOCK

Tough, aluminum ramp guides your speedloader tube to the maga-zine opening for fast, positive reloads. Steel mounting pins replace the front/rear trigger plate pins for solid attachment to the receiver. Works with the Armstec Speedloader bracket. abSPECS: Aluminum, natural finish. Fits all Benelli autoloading shotguns without fitting.

ARREDONDO BENELLI

SPEEDLOADER ASSIST BRACKETProvides Faster Reloads

For Higher Scores

#069-000-008AQ Benelli Speedloader Assist, 9F150Q09 � � � � � � � � � � � � � � � � � � � � � � � � � $ 165.99

Provides controlled carry of four or six, 3", 12 gauge shells for fast, fumble-free reloads. Clips to belt, allows spare rounds to be grasped with-out fumbling or dropping; reduces reload times. Spacers adapt for shorter rounds.SPECS: Plastic, black. Stainless steel belt clip. 51/2" (14cm) long, 25/8" (6.6cm) wide. Fits belts up to 21/4" (5.7cm).

CALIFORNIA COMP WORKS

12 GAUGE SPEED STRIPPERHolds Spare Ammo For Fumble-Free Reloads

#151-120-012AQ 12 Gauge Speed Stripper, 6-Round, 1E22B29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 24.99

#151-000-030AQ 12 Gauge Stripper, 4-Round, 1E22Q29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24.99

Creates a giant ramp that aligns the shell with the maga-zine tube for faster and easier reloading with either hand. Com-pletely replaces the small, factory carrier release button. Made from durable stainless steel; very easy to install, only minor fitting required. abSPECS: 17-4 stainless steel. 21/2" (6.3cm) long, 3/4" (19mm) wide. Includes roll pins and installation instructions. Fits Rem. 1100, 11-87, Sportsman 12 in 12 ga. only.

DAVE’S METAL WORKS REMINGTON 1100/11-87

EASYLOADERGiant Carrier Release Button

Makes Fast Reloads Easier

#260-100-000AQ 1100/11-87 Easyloader, 6B35A71 � � � � $ 39.99

Heavy duty, aluminum carriers hold additional rounds at the ready and allow incredibly fast reloads for the competitive shooter. The 3x3 Carrier holds six 2 ¾" shells in two stacks of three while the 4x4 holds two stacks of four. The Classic 4 Car-rier holds four rounds in a vertical stack for a slimmer profile. The bodies are machined from billets of aircraft aluminum that are hardcoat anodized and then fitted with 303 Hi-yield stain-less retention springs for ruggedness and reliability. Each AP carrier is and fitted with a Tec Lock but is also drilled to accept Safariland attachments. abSPECS: Aluminum, hardcoat anodized matte black. 303 stainless springs. 4x4 – 3¾" high x 25/8" wide. 3x3 – 27/8" high x 2- 5/8" wide. Classic 4- 3¾" high x 25/8" wide. Carriers accept 2¾" shells only.

AP INDUSTRIES

SHELL CARRIERSPositions 12 Gauge Shells

For Rapid Reloads

#100-007-067AQ 3x3 12 Gauge Shell Carrier, 5G64K49 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 69.99

#100-007-068AQ 4x4 12 Gauge Shell Carrier, 5G64N49 � � � � � � � � � � � � � � � � � � � � � � � � � � � 69.99

#100-009-958AQ Classic 4 Shell Carrier, 5G40C09 � � � 42.99

Innovative shell carriers retain pairs of 12 gauge shotshells of any length, one above the other, enabling competition shooters to load two shells at a time with either the strong or weak hand. Carriers are machined from solid billet aluminum, mounted to a Blade-Tech belt clip, with stain-less steel springs to securely hold shells in place. L2/4 holds two pairs of shells (4 total) attached to an alu-minum backer plate mounted on a Blade-Tech Tek-Lok belt clip and expanding the carrier to a 4 round system. L2/6 adds two more rounds for a total of 6. Independently adjustable at-tachment points allow the shooter to customize angle and ori-entation. Backer plate is drilled and tapped to accept Safariland ELS and Blade-Tech MOLLE attachments. abSPECS: Black and gray CNC machined aluminum frame. 303 stainless steel retainer springs. Black polymer Blade-Tech belt clip. L2/4: 41/2" (11.4cm) OAL, 23/4" (7cm) high, 23/4" (7cm) wide. L2/6: 41/2" (11.4cm) OAL, 23/4" (7cm) high, 43/4" (12.1cm) wide.

AP INDUSTRIES

L2 SERIES SHOTSHELL CARRIERSAllows Competitive Shooters To

Load Two Rounds Simultaneously

#100-011-865AQ L2/4 Carrier System, 5G45D89 � � � � � $ 49.99#100-011-866AQ L2/6 Carrier System, 5G68A89 � � � � � 74.99

Innovative shell carrier allows compe-tition shooters to grab four 12 ga. shells at once, resulting in quicker reloads. This four round shell loading technique is a highly efficient method that cuts reloading time in half. CNC machined from solid billet alu-minum, with 303 Hi-Yield springs for solid retention and smooth release, these carriers are built to withstand competition abuse. Carriers are mounted to a billet aluminum

backer plate that’s drilled and tapped to accept Safariland ELS and Blade-Tech Molle attachments. Adjustable backer plate al-lows you to set the angle of the quick loader to your preference. Available as a four round single carrier or an eight round double carrier. abSPECS: CNC aluminum body, 303 Hi-Yield springs, black and silver. Quad Load 4 – 4 1/2" (11.4cm) high, 2 1/4" (5.7cm) wide. Quad Load 8 – 4 1/2" (11.4cm) high, 5" (12.7cm) wide.

AP CUSTOM

QUAD LOAD CARRIER Allows Competition Shooters

To Reload Faster

#100-013-726AQ Quad Load 4, 5G46K39 � � � � � � � � � � � � � $ 49.99#100-013-727AQ Quad Load 8, 5G91J19 � � � � � � � � � � � � � � 99.99

Ideal for competition shooters, this handy belt caddy provides easy and immediate access to four extra shells. Made of strong, lightweight Derlin, caddy comes with a screw on belt clamp and can be mounted for either strong or weak hand use. Belt clamp is compatible with TEKLOK,

ELS, and MOLLE systems. Available for 12 ga. or 20 ga. shells. SPECS: Delrin, black. 3 ¾" (9.5cm) long, 2" (5.1cm) wide, ½" (1.3cm) thick.

TACCOM

QUICK CADDY SHOTSHELL HOLDER

Keeps Shotgun Shells Readily Available On Your Belt

#100-013-062AQ Quick Caddy 12GA Shotshell Holder, 8D21J89 � � � � � � � � � � � � � � � � � � � $ 24.95

#100-013-071AQ Quick Caddy 20GA Shotshell Holder, 8D22N89 � � � � � � � � � � � � � � � � � � 24.99

Belt mounted caddy al-lows you to grab two shells at once for faster reloading. Caddy holds up to 12 shells and the clips are properly spaced to permit quick ac-

cess to the shells. Made of durable polymer, the Backbone can be adjusted to your preference. abSPECS: Polymer, black. 8 ½" (21.6cm) OAL.

CARBON ARMS

BACKBONE SHOTSHELL HOLDER

Designed To Aid In Quicker Shotgun Reloads

#100-014-259AQ Backbone Shotshell Holder, 12rd., 2G106I39 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 123.99

Durable, injection-molded polymer shotshell holder gives competition shooters an upper hand in the often difficult shotgun stages. Optimized for competitors using the “Load-Two” method, the versatile holder positions 6 shells at your preferred position and angle to maximize reloading speed. Tek-Lok system enables attach-ment to popular competition belts. abSPECS: Injection-molded polymer, black. Holds (6) 12 ga. shotshells. Fits belts up to 2¼" (5.7cm) wide.

CARBON ARMS

6-ROUND PINWHEEL SHOTSHELL HOLDER

Competition Shell Holder Makes For Super-Quick

Reloads Using The “Load-Two” Method Shells not

included

#100-011-087AQ 6-Rd Pinwheel Shotshell Holder, 2G62D29 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 71.99

Rugged and lightweight, alu-minum shell holders put extra 12 gauge shotshells on the left side of the receiver for fast tactical reloads. Shells are held in place with a unique, internal San-toprene™ elastomer rib that securely retains even heavy slug shells during vigorous movement or heavy recoil. Available in sidemount (SM) or Pica-tinny rail (Pr) configurations. All nec-essary installation hardware, tools, and instructions included. remington Side-mount is available in 4-, 6-, and 8-round

capacities and uses steel-on-steel, threaded adapters that re-place the trigger group pins to anchor the shell holder securely to the receiver. Remington 870 shotguns require a shortened, tactical-style forend to accommodate 6- and 8-round side-mount units. Remington 1100/11-87 require minor forend alterations to fit the 8-round model. remington Picatinny is a 6-round model that features an integral Picatinny rail for mounting sights, optics, or other accessories. Wraps around the top and mounts to both sides of the receiver using the same type of attaching system as the sidemount model. Fits Remington 1100/11-87 without modification; requires use of shorter than factory length forearm when used with Reming-ton 870. Mossberg Sidemount is a 6-round unit that attaches in the same manner as the Remington Sidemount. Fits Mossberg 500/590/835. Mossberg Picatinny is a 6-round model with an integral Picatinny rail that fits guns that are drilled and tapped for a scope. Benelli Sidemount is available in 6- and 8-round versions to fit M1/M2 shotguns; includes an Allen head screw that replaces one trigger group pin to solidly secure the shell holder to the receiver. Benelli Picatinny models include an in-tegral Picatinny rail and mount to the top of factory drilled/tapped receivers. Available in 6-round for Benelli M1/M2 (re-quires drilling/tapping receiver for M1), 6- and 8-round for M4/M1014, and 4-round for Supernova shotguns. abSPECS: 6061 T6 aluminum, anodized, matte black. For 12 gauge only. All models include mounting hardware, rubber gasket, and installation instructions. Remington Sidemount fits models 870/1100/11-87 (may require modification to gun). Rem 4-Round Sidemount – 51/4" (13.3cm) long x 11/2" (3.8cm) high. 3.9 oz. (111g) wt. Rem 6-Round Sidemount – 61/4" (15.8cm) long x 11/2" high. 5.4 oz. (152g) wt. Rem 8-Round Sidemount – 73/4" (19.7) long x 11/2" high. 7 oz. (200g) wt. Remington Picatinny fits models 870/1100/11-87 (may require modification to gun). 7" (15.8cm) long x 21/2" (6.3cm) high. 7.6 oz. (215g) wt. Mossberg fits models 500/590/835. 6-round ony. 63/2" (16.2cm) long x 13/8" (3.5cm) high. 5.2 oz. (147g) wt. Mossberg Picatinny fits models 500/590/835 with drilled and tapped receivers. 6-round only. 7" long x 21/4" high. 6.4 oz. (182g) wt. Benelli Sidemount fits M1/M2. Benelli 6-Round Sidemount – 6" (15.2cm) long x 21/2" high. 6.3 oz. (179g) wt. Benelli 8-Round Sidemount – 73/4" long x 21/2" high. 8.1 oz. (230g) wt. Benelli Picatinny available for M2 (requires drilling tapping reciever to fit M1), M4/M1014, and Supernova. Benelli M2 6-Round Picatinny – 6" long x 2 (5.1cm)" high. 7.4 oz. (210g) wt. Benelli M4/M1014 6-Round Picatinny – 6" long x 2" (5.1cm) high. 7.5 oz. (213g) wt. Benelli M4/M1014 8-Round Picatinny – 73/4" long x 2" high. 9.5 oz. (268g) wt. Benelli Supernova 4-Round Picatinny – 8" (20cm) long x 13/4" (4.4cm) high. 6.2 oz. (176g) wt.

MESA TACTICAL

RECEIVER MOUNT SHOTSHELL HOLDER

Puts Extra Shotshells Right Where You Need Them

For Fast Loading

STOCK # FITS MODELrNDS PrICE#100-004-031AQ Rem 870/1100/11-87 SM 4 5A54N89 $ 59.99#100-002-648AQ *Rem 870/1100/11-87 SM 6 5A59I59 $ 64.99#100-003-295AQ *+ Rem 870/1100/11-87 SM 8 5A71N89 $ 79.99#100-004-030AQ * Rem 870/1100/11-87 PR 6 5A105I59 $ 117.99 100-013-724AQ Rem Versa Max PR 6 5A88L89 $ 99.99#100-002-649AQ Moss. 500/590/835 SM 6 5A63P39 $ 69.99#100-003-971AQ Benelli M1/M2 SM 6 5A63B39 $ 69.99#100-003-972AQ Benelli M1/M2 SM 8 5A76G09 $ 84.99#100-003-824AQ † Benelli M1/M2 PR 6 5A101A19 $ 114.99

STOCK # FITS MODELrNDS PrICE#100-002-650AQ Benelli M4/M1014 PR 6 5A101A19 $ 114.99#100-008-202AQ Mossberg 930 SM 6 5A63D39 $ 69.99#100-003-296AQ Benelli M4/M1014 PR 8 5A113Q79 $ 129.99#100-004-029AQ Benelli Supernova PR 4 5A88C89 $ 99.99

Bennelli Picatinny

Model

Shells not included

Shells not included

Shells not included

sho

tg

un

PAGE 217Orders/Tech: 800-741-0015order on the web

brownells.com

CO

MP

ET

ITIO

N G

EA

r

Unique rail system allows 12 extra rounds to be carried at the ready while providing over a foot of Picatinny rail for mount-ing sights or optics. Unit bolts onto the standard

KSG shotgun with no modifications or gunsmithing required. Optional 3½" Picatinny accessory rail can be added to the left or right side at the front for even more mounting options. abSPECS: Carrier – 6061 aluminum, matte black anodized finish. 153/8" length, 4¼" width at shell carriers. Mounting hardware and instructions included. Accessory Rail – 3½" long.

MESA TACTICAL KSG SHOTGUN

SURESHELL CARRIER & RAILRail System With

Ammunition Storage For Your KSG

#100-010-527AQ KSG SureShell Carrier, 5A211G34 � � $ 229.99#100-010-528AQ 3½" Picatinny Rail, 5A25B10 � � � � � � 29.99

Shell carrier attaches to buttstock and provides quick, convenient access to five additional shells for compe-tition, sporting clays, or hunting. Attaches to most synthetic or wooden stocks. Mounting hardware and template included. Requires drilling holes in stock. abSPECS: Polymer, black. Approximately 5" (12.7cm) long, 11/2" (3.8cm) wide. 1.1 oz. (32g) wt.

PHOENIX TECHNOLOGY

SHOT SHELL CARRIERHold 5 Shot Shells For Fast,

Convenient Reloading

#100-005-355AQ 12-ga. Shell Carrier, 3C7G14 � � � � � � � � � $ 8.99

Compact shell caddy in the “grab-two” style helps you complete super-fast reloads for competition or field shooting. Nylon holders retain six 2¾" shells securely during vigorous movement. Durable Tek-Lok belt clip from Blade Tech reliably fits belts up to 2¼" wide and adjusts vertically and to ±20 degrees cant angles for a custom fit. SPECS: Frame - Aluminum, hardcoat anodized, and molded polymer, matte black. Holds six, 2 ¾" 12-gauge shells. 53/8" (13.65cm) long, 3" (7.62cm) wide, 2" (5.08cm) thick overall. 8.1 oz. (230g) wt. w/o shells.

RAM SUPERIOR FIREARM SOLUTIONS

RAM SHELL CADDY Keeps 6 Shells At The Ready

For Fast Reloads

#100-011-677AQ Ram 12 Gauge Shell Caddy, 3Z44H29 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 49.99

Lightweight, molded-nylon shell carrier puts additional fire power quickly within your reach. Aluminum mounting plate attaches to the side of the receiver using the existing pin/screw holes—no perma-nent alterations or gunsmithing required. Four- and six-round models available for a variety of popular law enforcement shot-guns. rem. 870/1100/11-87 ESN has a convenient window in the mounting plate that leaves the weapon’s serial number exposed for viewing with the shell holder installed. Designed for armorers and law enforcement agencies who track their firearms by serial number for inventory, maintenance, and record keeping. abSPECS: Shell Holder - nylon plastic, black. Mounting Plate - aluminum, black, matte finish. 63/4" (17cm) long, 5.3 oz. (152 g) wt. (6-round). Includes mounting screws, pins and instructions. Field-grade forends that extend onto the sides of the receiver must be modified or replaced to provide adequate clearance for 6-shot shell holders.

TACSTAR

SIDE SADDLE SHELL HOLDERMounts To Receiver;

Holds Extra Rounds For Quick Reloads

STOCK # FITS/rNDS GA. PrICE#867-105-870AQ Rem. 870/1100/11-87/6 12 7F27D49 $ 29.99#867-105-874AQ Rem. 870/1100/11-87/4 12 7F24B09 $ 29.99#867-000-018AQ Rem. 870/1100/11-87 ESN/4 12 7F24A09 $ 29.99#867-000-005AQ Rem. 870/1100/1187/4 20 7F24A09 $ 29.99#867-105-120AQ Win. 1200/1300/6 12 7F26Q09 $ 29.99#867-105-500AQ Mossberg 500⁄6 12 7F26N09 $ 29.99#867-105-504AQ Mossberg 500⁄4 12 7F24H09 $ 29.99

Lightweight, polymer shell holder provides instant access to two spare 12 gauge shotshells for rapid reloads dur-ing competition or tactical operations. Compact, low-cut profile allows an easy

grasp of exposed shells for quick removal without hang-ups. Features a one-piece, wrap around belt clip with extra-long bottom hook for worry-free retention. Molded polymer con-struction. Fits belts up to 21/4" (5.7cm) wide.SPECS: Molded polymer, black. 17/8" (4.7cm) long, 13/4" (4.4cm) wide, 21/2" (6.3cm) high. Fits belts up to 21/4" (5.7cm) wide. 12 gauge only.

SAFARILAND

DOUBLE SHOTSHELL HOLDER

Puts Two Rounds In Easy Reach

#797-000-127AQ Double ShotShell Holder, 7G6H09 � � $ 7.99

Puts 6 additional shots right next to your hand for faster reloads. Balances the extra weight between your hands for no change in shouldering and aim. Attaches easily to Remington 870, 11-87 and 1100, 12 ga. receivers with threaded trigger-plate pins. abSPECS: Aluminum side plate, black anodized. Nylon-plastic shell holder, black. 63/4" (17cm) long, 5.3 oz. (152 g) wt. Includes screws, washers and Allen wrench. Extended forearms will require modification.

SCATTERGUN TECHNOLOGIES

SIDE-SADDLE SHELL HOLDERAttaches To Receiver;

Puts 6 Additional Shells Right At Your Fingertips

#800-303-780AQ Side Saddle Shell Holder, 8Z29P43 � $ 31.99

Lightweight shell carrier puts six additional shots within easy reach for fast reloads. The DSAC (Detachable Side Ammo Carrier) features an alu-

minum backing plate that secures to the receiver with the included replacement trigger pins and features. A hook-and-loop attachment system enables fast installation and removal of the separate shell carrier. Elastic webbing holds shells tight even when wet. Cut-out in mounting plate allows viewing of receiver serial number. Deluxe model come with two shell car-riers. Additional shell carriers available separately. abSPECS: Fits Remington 870/1100/11-87, 12 gauge only. Aluminum side plate, anodized, matte black. Stainless steel pins, natural finish. Elastic web shell holder, black. 63/4" (17cm) long x 11/2" (3.8cm) wide. 3.5 oz. (99g) wt.

VANG COMP SYSTEMS REM 870/1100/11-87

DETACHABLE SIDE AMMO CARRIERReceiver-Mounted

Carrier Puts 6 Additional Shells At

Your Fingertips

#100-005-245AQ Rem 870/1100/11-87 DSAC, 6K63K16 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 79.99

#100-005-247AQ Deluxe Rem 870/1100/11-87 DSAC, 6K83L33 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 96.99

#100-005-248AQ Extra Carrier, 6K19J95 � � � � � � � � � � � � � 19.95

Easy-to-install shell catcher grabs empty hulls being ejected from your 12-gauge shotgun and allows you to stow them away in a pocket or bag. Padded, double-sided tape se-cures catcher to the receiver and stays firmly in place; removes easily when not needed and won’t leave gummy residue be-hind. Fully adjustable for different guns and loads by open-ing or closing the wire as needed. Locks in the up position for singles, or down for doubles. abSPECS: Steel. Fits right-hand 12 gauge semi-auto shotguns. Includes instructions.

BIRCHWOOD CASEY

SAVE-IT SHELL CATCHERHolds Empties For

Easy Removal

#167-000-023AQ Save-It Shell Catcher, 1K11E09� � � � � � $ 12.99

Spring steel clip stops cases in the ejection port for easy removal. No more bending/stooping to pick up cases or losing them to ranges with “If it hits the ground, it’s ours” policies. Snaps easily to side of receiver just below the ejection port; snaps off when you need to cycle more than one round, as when shooting doubles. abSPECS: Spring steel, plastic coated, black, except TS-1100T, which has black TFE coating that blends in with most blued finishes. All models fit 12 gauge. TS-1100 and TS-1100T also fit all 20 gauge Rem 1100 models except Youth LT-20. TS-1100 will not operate on Rem. 1100 Classic Trap.

T&S SHELL CATCHERCatches Shotgun Empties;

Saves Them For Reloading

STOCK # MODEL FITS MATErIALS#869-012-111AQ TS-1100T 1100 & 11-87 TFE/steel#869-012-110AQ TS-1100 1100 & 11-87 Plastic/steel#869-012-002AQ TS-AL2 Beretta AL2,

A301/302/303/390ST/Urika 391, 20 ga. ONLY

Plastic/steel

#869-000-001AQ TS-A391 Beretta AL391, Urika, Urika 2 & Teknys, 12 ga. ONLY

Plastic/steel

#869-000-005AQ TS-A400 Beretta A400 XCEL Plastic/steel

— Advise # — Shell Catcher, 9F8N79 � � � � � � � � � � � � � � � � $ 10.99

Forend cap nut weighs 6 oz. to help ensure proper balance for a smooth swing and followthrough. CNC machined stainless steel with knurled rings for easy grasp; replaces original factory forend cap on Beretta 391 shotguns, 12 and 20 gauge. abSPECS: 17-4 Stainless steel, matte black. 111/16" (4.3cm) long x1-13/64" (3.1cm) dia. 6 oz. (170g) wt.

BRILEY BERETTA 391

FOREND CAPAdds Weight For Improved Balance

#129-000-261AQ 6 oz. Forend Cap, 9B55A71 � � � � � � � � � $ 62.99

Spring-loaded primer plunger pre-vents firing pin damage during dry-firing exercises. Treat the wool, chamber mop with your favor-ite gun oil to help prevent rusty chambers during storage. abSPECS: Aluminum head, wool mop. 31/2" (8.8cm) long. Available to fit 12 and 20 ga. Sold 2 per package.

CSP WOOLY SNAP CAPSPrevents Firing Pin & Rust Damage

#365-115-012AQ 12 Ga. Wooly Snap Caps, 5F18D20 � � $ 20.99#365-115-020AQ 20 Ga. Wooly Snap Caps, 5F18F20 � � 20.99

Interchangeable weights can be positioned anywhere along the barrel, varying the balance to suit the shooter. Set includes barrel clamp, 4, 6 and 8 oz. weights and adapters for attaching to 12, 20, 16, and .410 barrels. abSPECS: Aluminum clamp 2.25" (5.7cm) long. Weights: 4 oz. (113 g), 2.7" (6.8cm). 6 oz. (170 g), 3" (7.6cm). 8 oz. (226 g), 4.1" (10.45cm) long. .75" (5.7cm) diameter.

GRACO

ALL GAUGE COUNTERWEIGHT

#352-088-000AQ Counterweight Set, 2E44N79 � � � � � � � $ 67.49

Universal Set Fits Over/Unders & Singles

The spring-loaded “primers” in these snap caps act much like a live primer and cushion the blow so firing pin and bushing damage won’t occur. Bright color and “different” feel to prevent mixing with live rounds or function-testing dummies. (Don’t use snap caps as dummies - they don’t duplicate loaded round weight/balance). abSPECS: Brass base, plastic body.

TRIPLE-K DELUXE SNAP CAP FOR SHOTGUNS

Save Firing Pins - Shoot Better With Safe, Dry-Fire Practice

STOCK # CALIBEr/GA. CAPS PEr PAK PrICE#055-801-012AQ 12 Ga 2 6H6H47 $ 8.99#055-815-016AQ 16 Ga 2 6H6L47 $ 8.99#055-802-020AQ 20 Ga 2 6H5J49 $ 7.99#055-803-410AQ .410 Ga 2 6H6P47 $ 8.99

Heavy duty, 1000 denier Cordura® ny-lon pouch hangs at thigh level for quick, easy access to your shells when shooting trap, skeet, and clays. Durable, doubles-titched partition divides the pouch into two separate compartments, one to hold a box of shells for 25-round competition, the other to store empties. Side mounted pocket is ideal for storing your shooting glasses, extra choke tubes or other gear and includes an overlapping cover with hook-and-loop latch for a tight seal that won’t open unexpectedly. Conveniently lo-cated elastic shell holder stores up to three extra shells for quick access. Brass coated “D” ring allows attachment of additional accessories like ear muffs or range cloth. Adjustable belt pro-vides a custom fit to any size shooter. abSPECS: Pouch - 1000 denier Cordura nylon, brown or hunter green. 7" (17.8cm) long, 5" (12.7cm) wide, 8" (20cm) high. Pocket - 41/4" (10.8cm) long, 1" (2.5cm) wide, 7" (17.8cm) deep. 20 oz. (567g) wt.#084-000-305AQ Dump Pouch, Brown, 4H35Q82 � � � � $ 42.99#084-000-307AQ Dump Pouch, Hunter Green,

4H35L82 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42.99

SHOTGUN DUMP POUCHFor Fast, Easy Reloading During Competition

sho

tg

un

PAGE 218 Office/Tech: 641-623-5401SATISFACTION GUARANTEED

SINCE 1939

TA

CT

ICA

L A

CC

ESS

Or

IES

High quality, OEM components allow you to easily trans-form your Mossberg 500 into a reliable, high-capacity, self defense weapon. 20" long barrel chambered for 23/4" and 3" magnum 12 gauge loads features a fixed cylinder choke for maximum pattern coverage at combat ranges. Available with a single, brass front bead sight or rifle sights (white bead front with adjustable U-notch rear) that help provide rifle-like ac-curacy when shooting slugs at longer distances. Magazine extension threads solidly into the receiver to provide 8-rounds of firepower; knurled takedown screw retains the tube in the magazine support on the barrel to eliminate the need for a separate barrel clamp. Includes extended-length magazine spring for reliable feeding.SPECS: Barrel - Steel, blued finish. 20" (51cm) long. Smoothbore, fixed cylinder choke with rifle sights or single brass front bead sight only. 23/4" & 3" magnum 12 gauge. Extension Tube - Steel, blued finish, 8-round capacity. Magazine Spring - Piano wire, extended length. Kit fits Mossberg 500, 12 gauge receivers only.

MOSSBERG 500

HIGH CAPACITY SHOTGUN KIT

Converts Your Field Gun To A Tactical Workhorse

#078-000-162AQ High Capacity Shotgun Kit w/Rifle Sights, 1C151G81 � � � � � � � � � � � � � � � � � � $ 179.99

#631-000-339AQ High Capacity Mossberg 500 Kit w/Front Bead Sight, 1C90H80 � � � � � 99.99

Stamped, all-steel handguard clamps quickly to plain bar-reled, self-defense shotguns and protects your hands from contact with a hot barrel. Requires no permanent alterations and adds only a minimum amount of extra weight. abSPECS: Steel, blue, matte finish. 14" (35mm) long. Fits most non- ribbed, 12 ga. barrels. Includes instructions.

TACSTAR

SHOTGUN BARREL SHROUD

Prevents Contact With Hot Barrel

#867-102-012AQ Barrel Shroud, 7F26G08 � � � � � � � � � � � � $ 29.99

During competition or a tactical situ-ation, you can’t afford to lose time fum-bling to position your hand on the fore-arm, or, worse yet, have it slide off when racking a pump action shotgun. This rubber-coated, ergonomically shaped handstop attaches to any Picatinny rail forend to provide precise, tactile index-

ing of the support hand, so you keep your eyes on the target while mounting the weapon. Helps keep hand in position dur-ing recoil, too, for fast follow-up shots. Dual cross-bolts clamp the stop tightly to the rail for a solid, movement-free installa-tion. abSPECS: Synthetic-rubber coated molded polymer, black. Steel cross-bolts, oxide finish, matte black. 1¼" long x 1¼" wide at base. Extends 1¾" (4.5cm) below rail.

FALCON INDUSTRIES

ERGO GRIP® SURESTOP HANDSTOPFast, Precise, Tactile Hand Placement

On Railed Forends

#573-000-052AQ SureStop Rail Handstop, 3G8D57 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 9.99

High-quality sling adapter installs easily to provide Rem-ington 870 shotgun with a side, loop-style sling mount be-tween the buttstock and receiver. Smooth, flush fit won’t clutter the looks of your shotgun or leave an uneven, uncomfortable surface. abSPECS: Billet machined from 6061 aluminum, black. Right-hand only.

MIDWEST INDUSTRIES

SHOTGUN ENDPLATE SLING ADAPTERS

Tough, No Hassle Mounting System For Shotgun Slings

#100-002-335AQ RH Loop Adptr Rem 870, 2A23A69 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 29.99

Keep the shooter’s hand behind the muzzle on short barreled 870s equipped with extended magazines. Includes detent locking ball. Installs under the magazine cap. Accepts up to 11/4" slings. ab

SPECS: Steel, black Parkerized. 21/2" (6.3cm) high, 11/2" (3.8cm) wide.

LEFT SIDE SLING MOUNT - Side mounting keeps the triggerguard out where you can grab it faster. Accepts up to 11/4" wide slings.SPECS: 4130 steel, black, Parkerized finish. 23/16" (5.5cm) high, 11/2" (3.8cm) wide.#800-100-005AQ Rem 870 Left Side Sling, 8Z9F07 � � � $ 11.35

SCATTERGUN TECHNOLOGIES REM 870

TACTICAL RESPONSE SLING MOUNT

Accepts Popular Web Slings

#800-100-003AQ Rem 870 Mount, 8Z8J69 � � � � � � � � � � � $ 11.99

This dual-purpose sling attachment point is also a clamp that keeps the bar-rel and extended magazine tube securely tied together. May be configured for use with pushbutton QD sling swivels or sin-gle-point, clip-on sling loops, including Magpul’s MS3 Para-clip™, HK-style clips, and ITW™ MASH hooks. All-steel con-struction with tough matte black Melonite® finish. rem/Moss fits Remington 870 and Mossberg 500/590/Maverick. Separate model for Mossberg 590A1. Both models fit 12 gauge only. ab

MAGPUL SHOTGUN FORWARD SLING MOUNT

Support For Extended Mag Tube & Mounting Point For Tactical Slings

100-010-976AQ Rem/Moss Fwd Sling Mount, 3K25I59 � � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 28.99

#100-011-574AQ Mossberg 590A1 Fwd Sling Mount , 3K25C29 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 28.99

Easy-to-install accessory rail unit instantly adds three MIL-STD 1913 Picatinny rails to your SLP MK 1 to provide greatly expanded accessory mounting capabilities. 3, 6,

and 9 o’clock-positioned Picatinny-compatible rails accom-modate lights, lasers, or other devices. Easy-to-install tube slides over the magazine tube - no special tools or gunsmith-ing required. SPECS: Alluminum, hard-anodized matte black finish. Fits FNH SLP Mk 1 shotgun only.

FNH USA SLP MK 1

TRI-RAIL EXTENSIONAdds Side & Bottom

Picatinny Rails To Tactical Or Competition Gun

#119-000-063AQ SLP MK1 Tri-Rail Extension, 9A108H33 � � � � � � � � � � � � � � � � � � � � � � � � � $ 119.99

Designed for tactical operations, these mounts place the rear sling attachment point in front of the operator, so you can quickly shoulder your weapon without getting tangled. Allows single point sling attachment, or use with a front sling mount for two-point sling installation. Loop accepts slings up to 11/4" wide. rear Mount installs directly behind receiver, in front of buttstock. Precision machined from aluminum billet, then hardcoat anodized matte black. Right hand model for Reming-ton 870, 1100, and 11-87 positions sling on left side of stock. Am-bi model for Remington 870, 1100, and 11-87 accepts HK-style clasps and other clip-on sling fasteners. Benelli version fits M1, M3, and Super 90 combat shotguns, and can be positioned with the loop on either side of the receiver to accommodate right- or left-handed shooters. rem Front Mount positions the sling on the right side for Remington shotguns with external retention type magazine caps; a ball-bearing detent locks mount into magazine cap to prevent rotation. Moss rear mounts fit Moss-berg 500/590 and are available with a slot that accepts a sling up to 11/2" wide, a loop for HK-style clip-on slings, or a socket for a single-point, QD pushbutton sling swivel (swivel included). abSPECS: Rem Rear Mount - Aluminum, matte black. 1/4" (6.4mm) long, 113/16" (4.6cm) wide, 17/8" (4.8cm) high. Fits 870/1100/11-87, Right Hand only. Rem Ambi Rear Mount - Aluminum, matte black. 1/4" long, 21/4" (5.7cm) wide, 17/8" high. Fits 12 gauge Rem 870/1100/11-87. Also fits large-frame 20 gauge Rem. 870. Benelli Rear Mount - Aluminum, matte black. 3/16" (4.8mm) long, 115/16" (4.8cm) wide, 131/32" (5cm) high. Fits M1/M3/Super 90, Ambidextrous. Rem Front Mount - AS-35 Geneva steel, matte black. 7/64" (2.6mm) long, 21/4" (5.6cm) wide, 11/2" (3.8cm) high. Fits 870/1100/11-87 with early style external retention magazine caps. Moss - all models fit Mossberg 500/590.

GG&G

SHOTGUN SLING MOUNT

Allows Smooth, Unrestricted Sling Movement

Rem. Ambi Rear

#336-000-010AQ Rem Right Hand Rear Mount, 6C26M99 � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 26.99

#336-000-029AQ Rem Ambi Rear Mount, 6C26G99 � � 26.99#336-000-005AQ Benelli Rear Mount, 6C26G99 � � � � � � 26.99#336-000-009AQ Rem Front Mount, 6C9M99 � � � � � � � � 9.99 336-000-044AQ Moss Rear Mount w/Slot,

6C26E99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 26.99 336-000-046AQ Moss Rear Mount w/HK Loop,

6C26C99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 26.99 336-000-047AQ Moss Rear QD Mount w/Swivel,

6C36E49 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39.99

Rem. Front

Rem. RH Rear

Bennelli Rear

Low profile, loop-style sling adapter provides single-

point sling attachment for HK-style quick-releases. Have both hands free for quick access to a second weapon and maintain complete control of your shotgun, or make a rapid switch from right-hand to left-hand carry. Stainless steel crosspin replaces original trigger group pin for a rock-solid attachment point. Loop is free to rotate; rubber gasket prevents marring receiver finish. Loop is stamped from heavy-duty, 11 gauge steel, then treated with a mil-spec manganese phosphate finish for wear resistance. abSPECS: Pin - Stainless steel. Loop - 11 gauge steel, mil-spec manganese phosphate finish, matte black. Includes hardware, Allen head wrenches, and installation instructions. Fits Remington 870/1100/11-87, 12 gauge only.

Ultra-Low Profile, Snag-Free Design

For HK-Style Connectors

#100-004-033AQ Receiver Mount Sling Attachment, 5A16N89� � � � � � � � � � � � � � � � � � � � � � � � � � � � $ 18.99

MESA TACTICAL REM 870/1100/11-87

RECEIVER MOUNT SLING ATTACHMENT

Mount

Model

Want To Know More About Maintaining

Your Shotguns?

Go to the LEArN tab at brownells.com to view videos and read articles on your gun.