cabrio---washer

W10405142BW10405143B - SP

Designed to use only HE High Efficiency detergents.Conue uniquement pour une utilisation avec des dtergents HE Haute efficacit.

TOP-LOADING HIGH EFFICIENCY

LOW-WATER WASHERUSE AND CARE GUIDE

Table of ContentsWASHER SAFETY .........................................................2WHATS NEW UNDER THE LID? .................................3CONTROL PANEL AND FEATURES ......................................4 Dispensers .......................................................................5CYCLE GUIDE ...............................................................6USING YOUR WASHER ................................................8WASHER MAINTENANCE .............................................. 11TROUBLESHOOTING ...................................................... 13WARRANTY........................................................................ 18ASSISTANCE OR SERVICE ...........................Back Cover

Table des matiresSCURIT DE LA LAVEUSE ......................................19QUOI DE NEUF SOUS LE COUVERCLE? ................20

TABLEAU DE COMMANDE ET CARACTRISTIQUES ..........................................21 Distributeurs ..................................................................22GUIDE DES PROGRAMMES ......................................23UTILISATION DE LA LAVEUSE ..................................26ENTRETIEN DE LA LAVEUSE ........................................ 30DPANNAGE ...................................................................... 32GARANTIE .......................................................................... 39ASSISTANCE OU SERVICE ..............Couverture arrire

LAVEUSE HAUTE EFFICACIT FAIBLE

CONSOMMATION DEAU AVEC CHARGEMENT

PAR LE DESSUS GUIDE DUTILISATION

ET DENTRETIEN

Para una version en espanol, visite www.whirlpool.com

2WASHER SAFETY

3WHATS NEW UNDER THE LID?

Choosing the Right DetergentUse only High Efficiency detergents. The package will be marked HE or High Efficiency. Low-water washing creates excessive sudsing with a regular non-HE detergent. Using regular detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturers instructions to determine the amount of detergent to use.

Normal Sounds You Can ExpectAt different stages of the wash cycle, you may hear sounds and noises that are different from those of your previous washer. For example, you may hear a clicking and hum at the beginning of the cycle, as the lid lock goes through a self-test. There will be different kinds of humming and whirring sounds as the washplate moves the load. And sometimes, you may hear nothing at all, as the washer determines the correct water level for your load or allows time for clothes to soak.

Use only High Efficiency (HE) detergent.

Concentrated CleaningLow-water cleaning means concentrated cleaning. Rather than diluting detergent as done in an agitator-style washer, this washer delivers the detergent directly to the soils.

Automatic Load Size SensingOnce you start the cycle, the lid will lock, and the washer will begin the sensing process to determine the correct water level for the load. You will hear the motor turn the basket in short pulses to thoroughly wet the load. This low-water wash method uses less water and energy compared to a traditional agitator-style washer.

Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate; when loaded, the center of the washplate should be visible.

As the washer dampens and moves the load, the level of the garments will settle in the basket. This is normal, and does not indicate that more garments should be added. IMPORTANT: You will not see a washer basket full of wateras with your past agitator-style washer. It is normal for some of the load to be above the water line.

Cleaning with Less Water

The most striking difference in your new washer is the low-water washplate wash system. The washer automatically adjusts the water level to the load sizeno water level selector is needed.

Traditional agitator-style washer

Low-water washer

WashplateWashplate

4CONTROL PANEL AND FEATURES

POWER BUTTONPress to turn the washer ON. Pressing once while the washer is on will cancel the current cycle. Pressing twice will turn the washer OFF.

WASH CYCLE KNOBTurn the Wash Cycle knob to select a cycle for your laundry load. See Cycle Guide for detailed descriptions of cycles.

TIME/STATUS DISPLAYThe Estimated Time Remaining display shows the time required for the cycle to complete. Factors such as load size and water pressure may affect the time shown in the display. Overloading, unbalanced loads, or excessive suds may cause the washer to adjust the cycle time, as well. If you have set a delay start to the cycle, the Estimated Time Remaining display will show the delay time adjusted. When the cycle is complete, the DONE indicator will light until the lid is opened. The Lid Lock indicator lights up when the lid is locked and cannot be opened. If you need to open the lid, press START/PAUSE. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Press START/PAUSE again to restart the cycle.

ECO MONITORYour washer is specially designed to conserve energy and water. Each cycle, along with any selected options, will result in different energy and water usage. To use the Eco Monitor, choose the best cycle for the load being washed, then adjust temperature and spin speed options to improve the energy usage within that cycle.

START/PAUSE BUTTONPress to start the selected cycle; press again to pause a cycle.

CYCLE SIGNAL BUTTONUse this option to adjust volume of the signal that sounds at end of cycle. A louder signal is helpful in removing items as soon as cycle is complete.

CYCLE OPTIONS You may add or remove options for each cycle. Note that not all options can be used with all cycles, and some are preset to work with certain cycles.

ECOBOOST The EcoBoost option allows you to increase your energy savings on your wash cycles. When this option is used,

1

1

2

3

3

42

the wash cycle will use cooler wash water than the selected cycle and may increase the spin speed for faster drying.

EXTRA RINSE This option can be used to automatically add a second rinse to most cycles.

FABRIC SOFTENER DISPENSER Press this button to set the Fabric Softener dispenser to automatically add liquid fabric softener to the load at the correct time.

CYCLE MODIFIERSWhen you select a cycle, its default settings will light up.

SOIL LEVELSoil level (wash time) is preset for each wash cycle. As you press the Soil Level pad, the cycle time (minutes) will increase or decrease in the Estimated Time Remaining display and a different wash time will appear. For most loads, use the soil level that is preset with the cycle you have chosen. For heavily soiled and sturdy fabrics, press SOIL LEVEL to select more wash time, if needed. For lightly soiled and delicate fabrics, press SOIL LEVEL to select less wash time, if needed. A lower soil level setting will help reduce tangling and wrinkling.

SPIN SPEEDThis washer automatically selects the spin speed based on the cycle selected. The preset speeds can be changed. Not all spin speeds are available with all cycles. Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load. Slower spin speeds mean less wrinkling, but will leave

your load more damp.

WASH TEMP Temperature Control senses and maintains uniform water temperatures by regulating incoming hot and cold water. Select a wash temperature based on the type of fabric and soils being washed. For best results and following the garment label instructions, use the warmest wash water safe for your fabric. Warm and hot water may be cooler than what your

previous washer provided. Even for cold wash settings, some warm water may

be added to the washer to maintain a minimum temperature.

5

4

5

6

6

7

8

Not all features and cycles are available on all models.

8 7

5Dispensers

High Efficiency HE detergent dispenserAdd liquid or powdered HE detergent to this dispenser for your main wash cycle.

A B

C

Use only High Efficiency (HE) detergent.

Liquid chlorine bleach dispenserThis dispenser holds up to 3/4 cup (180 mL) liquid chlorine bleach. The bleach will be automatically diluted and dispensed at the optimum time during the the wash cycle. This dispenser cannot dilute powdered bleach.NOTE: Fill dispenser only with liquid chlorine bleach.

Liquid fabric softener dispenserPour measured liquid fabric softener into the liquid fabric softener dispenser, if desired. It will dispense automatically at the optimum time when the Fabric Softener option is selected. Use only liquid fabric softener in this dispenser.

A

C

B

6Sturdy fabrics, colorfast items

Heavy Duty

Hot Warm Cool Cold

High Medium

Low

Heavy Normal Medium

Light

Use this cycle for heavily soiled or sturdy cotton items. This cycle combines high-speed wash action, longer wash time, and extra high-speed spin to shorten drying times. Adjust temperature settings as needed.

Extra Rinse EcoBoost

Fabric Softener

Large items such as sleeping bags, small comforters, jackets

Bulky Items

Hot Warm Cool Cold

Medium Low

Heavy Normal

Medium Light

This cycle is designed for oversized items that do not easily absorb water, such as comforters, pillows, and poly-filled jackets. The cycle uses an initial soak to thoroughly saturate the item(s).


Fabric Softener

CYCLE GUIDE

Items to wash: Cycle: Wash Temp*:

Spin Speed:

Soil Level:

Available Options:

Cycle Details:

Machine-wash silks, hand-wash fabrics and wool

Handwash/ Delicate

Medium Low

Heavy Normal Medium

Light

Extra Rinse Fabric Softener


Lightly soiled garments

No-iron fabrics

Bright or darklycolored cottons,linens, casual andmixed loads

Quick Wash

Perm Press/ Casual

Cold Wash/Clean Care

Hot Warm Cool Cold

Hot Warm Cool Cold

Cold

High Medium

Low

High Medium

Low

High Medium

Low

Heavy Normal Medium

Light

Heavy Normal

Medium Light

Heavy Normal Medium

Light

Use this cycle for machine-washable delicate garments. This cycle uses intermittent wash action with cool water and slow spin to gently care for fine washables and avoid shrinkage. Place small items in mesh bags before washing.

Use this cycle to wash small loads of 23 lightly soiled garments that are needed in a hurry. This cycle combines a fast agitation, a shortened wash time, and a high-speed spin to shorten drying times.

Use this cycle for lightly soiled office wear. The cycle uses a warm wash, a cooldown, and medium spin speeds for better wrinkle performance.

This cycle uses cold water wash and a concentrated detergent solution to gently lift out stains and care for fabrics. Settings may be adjusted as desired, but must use only cold water settings.


Fabric Softener


Fabric Softener

Normally soiled sheets

Sheets Hot Warm Cool Cold

High Medium

Low

Heavy Normal

Medium Light

Use this cycle to wash bed sheets. This cycle uses extra water and a special wash action to reduce tangling.


Fabric Softener

Cottons, linens, and mixed garment loads

Normal Hot Warm Cool Cold

High Medium

Heavy Normal** Medium

Light

Use this cycle to clean normally soiled cottons and mixed fabric loads. Default settings can be adjusted as needed.


Fabric Softener

Warm Cool Cold

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load being washed. If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.Not all cycles and options are available on all models.

Athletic and high-performance wear

Active Wear

Hot Warm Cool Cold

High Medium

Low

Heavy Normal

Medium Light

Use this cycle to wash loads of no-iron fabrics such as sport shirts and other active wear.


Fabric Softener

Soiled white fabrics

Whites Hot Warm Cool Cold

HighMedium

Low

HeavyNormalMedium

Light

This cycle adds liquid chlorine bleach to the load at the proper time for improved whitening of soiled white fabrics.


Fabric Softener

* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.** Not all models default to the same Soil Level setting. Some models will default to Medium on this cycle.

7CYCLE GUIDE

Items to wash: Wash Temp*:

Spin Speed:

Soil Level:

Available Options:

Cycle Details:

Swimsuits, items that need rinsing only

Rinse & Spin

High Medium

Low

This cycle uses a high-speed spin. For some fabrics, you may wish to set the spin speed to a lower setting.

EcoBoost Fabric Softener

Wet load of clothes

Drain & Spin

High Medium

Low

Use this cycle to spin excess water out of a load. This cycle drains the water and spins at a high speed. Spin speed is adjustable.

No clothes in washer

Clean Washer

with affresh

Cycle:

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load being washed. If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.Not all cycles and options are available on all models.

For models with separate cycle knob positions for Rinse & Spin and Drain & Spin:

Swimsuits, items that need rinsing only

Rinse/Drain & Spin

High Medium

Low

This cycle uses a high-speed spin. For some fabrics, you may wish to set the spin speed to a lower setting.


Wet load of clothes

Rinse/Drain & Spin

High Medium

Low

To select, choose Rinse/Drain & Spin and turn off Extra Rinse. Use this cycle to spin excess water out of a load. This cycle drains the water and spins at a high speed. Spin speed is adjustable.

For models with a Rinse/Drain & Spin cycle position:

EcoBoost Use this cycle every 30 washes to keep the inside of your washer fresh and clean. This cycle uses a higher water level. Use with affresh Washer Cleaner tablet or liquid chlorine bleach to thoroughly clean the inside of your washer. This cycle should not be interrupted. See Washer Care.IMPORTANT: Do not place garments or other items in the washer during the Clean Washer with affresh cycle. Use this cycle with an empty wash tub.

Heavily soiled fabrics

Soak Warm Cool Cold

Heavy Normal Medium

Light

Use this cycle to soak small spots of set-in stains on fabrics. After time has expired, washer will drain, but will not spin and a tone will sound. To set a follow-up cycle, add additional detergent and select a cycle based on fabric type.

EcoBoost

* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.

8USING YOUR WASHER

Empty pockets. Loose change, buttons, or any small object can pass under the washplate and become trapped, causing unexpected sounds.

Sort items by recommended cycle, water temperature, and colorfastness.

Separate heavily soiled items from lightly soiled. Separate delicate items from sturdy fabrics. Do not dry garments if stains remain after washing; heat

can set stains into fabric. Treat stains promptly. Close zippers, fasten hooks, tie strings and sashes.

Remove non-washable trim and ornaments. Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips: When washing water-proof or water-resistant items, load

evenly. See Cycle Guide for tips and more information on using the Bulky Items cycle.

Use mesh bags to help prevent tangling when washing delicate or small items.

Turn knits inside out to avoid pilling. Separate lint-takers from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care labels instructions to avoid damage to your garments.

1. Sort and prepare your laundry

Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate; when loaded, the center of the washplate should be visible. Try mixing different sized garments to reduce tangling.

IMPORTANT: Garments need to move freely for best cleaning and to reduce wrinkling and tangling.

3. Load laundry into washer

Single-dose laundry packet, color-safe bleach, Oxi-type boosters, or fabric softener crystals can be added to the basket prior to adding laundry.

NOTE: Do not add clothes to washer basket prior to adding laundry products. Always follow manufacturers instructions.

2. Add single-dose laundry packet, Oxi, color-safe bleach, or fabric softener crystals (if desired)

9Add a measured amount of HE detergent into detergent dispenser. IMPORTANT: Use only High Efficiency detergents. The package will be marked HE or High Efficiency. Low-water washing creates excessive sudsing with a regular non-HE detergent. Using regular detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturers instructions to determine the amount of detergent to use. NOTE: If using an Oxi laundry boost product, add to the detergent dispenser.HELPFUL TIP: See Washer Maintenance for information on recommended method of cleaning washer dispensers.

Pour a measured amount of liquid fabric softener into dispenser; always follow manufacturers directions for correct amount of fabric softener based on your load size. Then select Fabric Softener option. IMPORTANT: Fabric Softener option must be selected to ensure proper distribution at correct time in cycle. Do not overfill or dilute. Overfilling dispenser will cause fabric softener to immediately dispense into washer. If Extra Rinse option is selected, fabric softener will be dispensed in the last rinse.NOTE: Do not use liquid fabric softener dispenser balls in this washer. They will not dispense correctly.

5. Add liquid chlorine bleach to dispenser

7. Press POWER to turn on washer

4. Add HE detergent to dispenser

6. Add liquid fabric softener to dispenser

Detergent dispenser

Fabric softener dispenser

Do not overfill, dilute, or use more than 3/4 cup (180 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.

Liquid chlorine bleach dispenser

NOTE: Do not add single-dose laundry packets, color-safe bleach, Oxi-type boosters, or fabric softener crystals to dispensers. They will not dispense correctly.

10

Turn cycle knob to choose your wash cycle. Estimated Time Remaining will light up with a cycle time. You may notice time adjusting during the cycle. This is normal. If you do not want to begin a cycle immediately, you may choose the DELAY WASH option.

To choose a delay time:1. Press DELAY WASH button to select desired delay time.2. Press START/PAUSE to set the delay. The delay countdown

has started when the START/PAUSE light stops blinking.

To cancel delaying a cycle:1. Press START/PAUSE again to begin a wash cycle

immediately.IMPORTANT: When delaying a cycle, use liquid HE detergent only in the dispenser. Powdered detergents may absorb moisture from a previous cycle and clump before the wash cycle begins.

8. Select cycle Wash TempHotSome cold water is added to save energy. This will be cooler than your hot water heater setting.

Warm Some cold water will be added, so this may be cooler than what your previous washer provided.

Cool Warm water is added to assist in soil removal and to help dissolve detergents.

Cold Warm water may be added to assist in soil removal and to help dissolve detergents.

Suggested Fabrics

Whites and pastels

Durable garments

Heavy soils

9. Select cycle modifiers, if desired

Once you select a cycle, the default settings for that cycle will be lit. Press the cycle modifiers buttons to change the Soil Level, Spin Speed, and Wash Temp, if desired. Not all settings are available with all cycles. NOTE: Always read and follow fabric care labels instructions to avoid damage to your garments.

11. Press START/PAUSE to begin wash cycle

10. Select cycle options

Select any other cycle options you may wish to add, if not previously set. Some cycles will automatically add certain options such as Extra Rinse. These may be turned off, if desired.NOTE: Not all options are available with all cycles.

Bright colors

Moderate to light soils

Dark colors that bleed or fade

Light soils

Press the START/PAUSE button to start the wash cycle. When the cycle has finished, the DONE indicator will light and the end of cycle signal will sound (if set). Promptly remove garments when cycle is done to avoid odor, reduce wrinkling, and rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add garmentsIf you need to open the lid to add 1 or 2 missed garments:Press START/PAUSE; the lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Then close lid and press START/PAUSE again to restart the cycle.If lid is left open for more than 10 minutes the water will pump out.

Dark colors that bleed or fade

Light soils

11

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.NOTE: This washer does not include inlet hoses. See the Installation Instructions for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer Clean and Performing at its Best1. Always use High Efficiency (HE) detergents and follow the

HE detergent manufacturers instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help dry out the washer and prevent the buildup of odor-causing residue.

Cleaning Your Top Loading WasherRead these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the WasherTo keep your washer odor-free, follow the usage instructions provided above, and use this recommended monthly cleaning procedure:

Clean Washer CycleThis washer has a special cycle that uses higher water volumes in combination with affresh Washer Cleaner or liquid chlorine bleach to clean the inside of the washer.Begin procedure1. affresh Washer Cleaner Cycle Procedure

(Recommended for Best Performance): a. Open the washer lid and remove any clothing or items. b. Place an affresh Washer Cleaner tablet in the bottom

of the washer basket. c. Do not place an affresh Washer Cleaner tablet

in the detergent dispenser. d. Do not add any detergent or other chemical to the

washer when following this procedure. e. Close the washer lid. f. Select the CLEAN WASHER cycle. g. Press the START/PAUSE button to begin the cycle. The

Clean Washer Cycle Operation is described below. NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER/CANCEL. (For models with no Power/Cancel button, press and hold START/PAUSE for three seconds). After the Clean Washer cycle has stopped, run a Rinse/Drain & Spin cycle to rinse cleaner from washer.

WASHER MAINTENANCE

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative): a. Open the washer lid and remove any clothing

or items. b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment. NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time. c. Close the washer lid. d. Do not add any detergent or other chemical

to the washer when following this procedure. e. Select the CLEAN WASHER cycle. f. Press the START/PAUSE button to begin the cycle.

The Clean Washer Cycle Operation is described below. NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER/CANCEL. (For models with no Power/Cancel button, press and hold START/PAUSE for three seconds). After the Clean Washer cycle has stopped, run a Rinse/Drain & Spin cycle to rinse cleaner from washer.

Description of Clean Washer Cycle Operation:1. This cycle will fill to a water level higher than in normal

wash cycles to provide rinsing at a level above the water line for normal wash cycle.

2. During this cycle, there will be some agitation and spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for better ventilation and drying of the washer interior.

Cleaning the DispensersAfter a period of using your washer, you may find some residue buildup in the washers dispensers. To remove residue from the dispensers, wipe them with a damp cloth and towel dry. Do not attempt to remove the dispensers or trim for cleaning. The dispensers and trim are not removable. If your model has a dispenser drawer, however, remove the drawer and clean it before or after you run the Clean Washer cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the WasherUse a soft, damp cloth or sponge to wipe away any spills. Use only mild soaps or cleaners when cleaning external washer surfaces. IMPORTANT: To avoid damaging the washers finish, do not use abrasive products.

12

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage or moving:1. Refer to Installation Instructions to locate, level, and

connect washer.2. Before using again, run washer through the following

recommended procedure:

To use washer again:1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.2. Plug in washer or reconnect power. 3. Run washer through BULKY ITEMS cycle to clean

washer and remove antifreeze, if used. Use only HE High Efficiency detergent. Use half the manufacturers recommended amount for a medium-size load.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water inlet hoses.

2. If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving.

3. Disconnect drain from drain system.4. Unplug power cord.5. Place inlet hoses inside washer basket.6. Drape power cord and drain hose over the console

and secure with masking tape.7. Place foam packing ring from original shipping materials

back inside washer. If you do not have packing ring, place heavy blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until washer is placed in new location.

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:1. Unplug or disconnect power to washer.2. Turn off water supply to washer, to avoid flooding

due to water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.To winterize washer:1. Shut off both water faucets; disconnect and drain water

inlet hoses.2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE/DRAIN & SPIN cycle for about 30 seconds to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

13

First try the solutions suggested here or visit our website at www.whirlpool.com/help for assistance and to possibly avoid a service call.

If you experience Possible Causes Solution

Feet may not be in contact with the floor and locked.

Front and rear feet must be in firm contact with floor, and washer must be level to operate properly. Jam nuts must be tight against the bottom of the cabinet.

Check floor for flexing or sagging. If flooring is uneven, a 3/4" (19 mm) piece of plywood under your washer will reduce sound.

See Level the Washer in the Installation Instructions.

Load could be unbalanced. Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate. Adding wet items to washer or adding more water to basket could unbalance washer.

Avoid washing single items. Balance a single item such as a rug or jeans jacket with a few extra items. If the dial is flashing, redistribute the load, close the lid, and press START/PAUSE.

Use Bulky Items cycle for oversized, non-absorbent items such as comforters or poly-filled jackets. Other items are not appropriate for Bulky Items cycle. See Cycle Guide.

Item or load not suitable for selected cycle. See Cycle Guide and Using Your Washer.

Empty pockets before washing. Loose items such as coins could fall between basket and tub or may block pump. It may be necessary to call for service to remove items.

Washer not level. Water may splash off basket if washer is not level.

Fill hoses not attached tightly. Tighten fill-hose connection.

Make sure all four fill hose flat washers are properly seated.

Drain hose connection Pull drain hose from washer cabinet and properly secure it to drainpipe or laundry tub.

Check household plumbing for leaks or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all household plumbing for leaks (laundry tubs, drain pipe, water pipes, and faucets.)

Fill hose washers

Noises For normal operating sounds, go to www.whirlpool.com/help.

It is normal to hear metal items on clothing such as metal snaps, buckles, or zippers touch against the stainless steel basket.

Objects caught in washer drain system.

Clicking or metallic noises

Gurgling or humming It is normal to hear the pump making a continuous humming sound with periodic gurgling or surging as final amounts of water are removed during the spin/drain cycles.

Washer may be draining water.

Water Leaks

Check the following for proper installation:

Do not place tape over drain opening.

An unbalanced load can cause basket to be out of alignment and cause water to splash off tub. See Using Your Washer for loading instructions.

Washer not loaded as recommended.

TROUBLESHOOTING

Vibration, rocking, or walking

Not enough water in washer

Load not completely covered in water.

This is normal operation for an HE low-water washer. The load will not be completely underwater. The washer senses load sizes and adds correct amount of water for optimal cleaning. See Whats New under the Lid.

IMPORTANT: Do not add more water to washer. Adding water lifts the garments off the washplate, resulting in less effective cleaning.

Washer not performing as expected

Washer may not be level.

Vibration or Off-Balance

Vibration during spinning or washer stopped with all dial lights flashing

Humming You may hear the hum of the sensing spins after you have started the washer. This is normal. Sensing spins will take several minutes before water is added to the washer.

The washer is sensing the load size.

14


Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not interrupt cycle.

Washer may be stopped to reduce suds.

The washer senses the dry load with short spins that may take 2 to 3 minutes before water is added. You may hear the hum of the spins. This is normal.

Washer wont run or fill, washer stops working (cont.)

Plug power cord into a grounded 3-prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.NOTE: If problems continue, contact an electrician.

Check proper electrical supply.

Washer may be tightly packed. Remove several items, rearrange load evenly around the washplate. Do not load garments directly over the center of the washplate. Close lid and press START/PAUSE.

Add only 1 or 2 additional garments after washer has started.

Not using HE detergent or using too much HE detergent.

Only use HE detergent. Suds from regular detergents can slow or stop the washer. Always measure detergent and following detergent directions based on your load requirements.

To remove suds, cancel cycle. Select RINSE/DRAIN & SPIN. Select your cycle. Press START/PAUSE. Do not add more detergent.

Small items may have been caught in pump or between basket and tub, which can slow draining.

Empty pockets and use garment bags for small items.

Washer not draining/ spinning, loads are still wet

Washer not performing as expected (cont.)

TROUBLESHOOTING

Do not add more water to the washer.




Washer wont run or fill, washer stops working

Check for proper water supply. Both hoses must be attached and have water flowing to inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.

15

Check plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form and securely attach to drainpipe or tub. Do not tape over drain opening. Lower drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from drain hose.


Suds from regular detergent or using too much detergent can slow or stop draining or spinning. Use only HE detergent. Always measure and follow detergent directions for your load. To remove extra suds, Select RINSE/DRAIN & SPIN. Do not add detergent.

Load is tangling Washer not loaded as recommended. Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate.

Reduce tangling by mixing types of load items. Use the recommended cycle for the type of garments being washed.

If you experience Possible causes Solution

Incorrect or wrong wash or rinse temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy Star qualified washers use cooler wash and rinse water temperatures than traditional top-load washers. This includes cooler hot and warm washes.

Load not rinsed Check for proper water supply.



TROUBLESHOOTING

Energy-saving controlled wash temperatures.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water flowing to the inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.


The suds from regular detergent can cause the washer to operate incorrectly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions based on load size and soil level.

Washer may be tightly packed. The washer is less efficient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate.

Use cycle designed for the fabrics being washed.


Fabric softener option not selected. When using fabric softener, be sure the Fabric Softener option is selected.

Sand, pet hair, lint, etc. on load after washing

Heavy sand, pet hair, lint, and detergent or bleach residues may require additional rinsing.

Add an Extra Rinse to the selected cycle.

Washer not draining/ spinning, loads are still wet (cont.)

Washer may be tightly packed or unbalanced.

Tightly packed loads may not allow the washer to spin cor-rectly, leaving the load wetter than normal. Evenly arrange the wet load for balanced spinning. Select RINSE/DRAIN & SPIN to remove excess water. See Using Your Washer for loading recommendations.

Using cycles with a lower spin speed. Cycles with lower spin speeds remove less water than cycles with high spin speeds. Use the recommended cycle/speed spin for your garment.

16



TROUBLESHOOTING


Not using correct cycle for fabric type.

Not using dispensers.

Not washing like colors together.

The suds from regular detergent can prevent washer from operating correctly.


Always measure detergent and follow detergent directions based on load size and soil level.

Use a higher soil level cycle option and warmer wash temperature to improve cleaning.

If using Quick Wash cycle (on some models), wash only a few items.

Use Whites or Heavy Duty cycle for tough cleaning.

See the Cycle Guide to match your load with the best cycle.

Use dispensers to avoid chlorine bleach and fabric softener staining.

Load dispensers before starting a cycle.

Avoid overfilling.

Do not add products directly onto load.

Wash like colors together and remove promptly after the cycle is complete to avoid dye transfer.


Monthly maintenance not done as recommended. Not using HE detergent or using too much HE detergent.

Run the Clean Washer with affresh cycle after every 30 washes. See Washer Care in Washer Maintenance.

Unload washer as soon as cycle is complete.


Always follow the detergent directions.

See Washer Care section.

Odors

Empty pockets, zip zippers, and snap or hook fasteners before washing to avoid snags and tears.

Sharp items were in pockets during wash cycle.

Strings and straps could have tangled.

Items may have been damaged before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if the load is tightly packed.

Load garments in loose heaps evenly around washplate. Do not load garments directly over the center of the washplate.

Load items should move freely during wash to avoid damage.

Use cycle designed for the fabrics being washed.


Tie all strings and straps before starting wash load.

Fabric Damage

Garment care instructions may not have been followed.

Always read and follow garment manufacturers care label instructions. See the Cycle Guide to match your load with the best cycle.

Washer not loaded as recommended.

Washer senses load size and adds correct amount of water. This is normal and necessary for clothes to move.

Do not add more water to washer. Adding water lifts the garments off the washplate, resulting in less effective cleaning.

Load garments in loose heaps evenly around the washplate. Do not load garments directly over the center of the washplate.


Not cleaning or removing stains

Wash load not completely covered in water.

Added more water to washer.

Wash action and/or spin speed too fast for load.

Select a cycle with a slower wash action and slower spin speed. Note that items will be wetter than when using a higher speed spin.

Load is tangling (cont.)

17

Liquid chlorine bleach may have been added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up bleach spills.Undiluted bleach will damage fabrics. Do not use more than recommended by manufacturer.Do not place load items on top of bleach dispenser when loading and unloading washer.


Clogged dispensers or laundry products dispensing too soon.

Do not overfill dispenser. Overfilling causes immediate dispensing.Always select Fabric Softener option to assure proper dispensing.Load dispensers before starting a cycle.It is normal for small amounts of water to be remain in dispenser at the end of the cycle.Homes with low water pressure may result in residual powder in the dispenser. To avoid, select a warmer wash temperature if possible, depending on your load.Use only liquid chlorine bleach in the bleach dispenser.

Incorrect dispenser operation


TROUBLESHOOTING


Error Code Appears in Display

oL (overloaded) appears in display

Load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.

Liquid chlorine bleach not used in dispenser.

uL (unbalanced load) appears in display

Load not balanced. The washer is running a load-balance correction routine.

Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

HC (hot and cold hoses reversed) appears in display

Hot and cold inlet hoses have been installed incorrectly.

This code will appear at the end of the wash cycle to indicate that cold water hose is connected to the hot water inlet and hot water hose is connected to the cold water inlet.

Sd (Excess suds) appears in display

Excessive suds in washer. Washer is running a suds reduction routine.

Allow the washer to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturers instructions. If the dial is flashing, reselect your desired cycle using a cold wash temperature, and press START/PAUSE. Do not add detergent.

dL (Lid cannot lock) appears in display

An item in the load may be keeping the lid from locking.

Check for items directly under the lid.

lid (Lid opened) appears in display

Washer lid left open. Close the lid to clear the display. If the lid is left open for more than 10 minutes, the cycle will reset and water in the washer will drain.

dU (Lid cannot unlock) appears in display

Objects on washer lid prevent it from unlocking.

Remove objects, such as a basket of laundry, from the top of the washer.

F## code (F-type error code) appears in display

System error code. Press START/PAUSE once to clear the code. Then press START/PAUSE again to restart washer. If code appears again, call for service.

LF (too long to fill) appears in display

Washer taking too long to fill. Drain extends more than 4.5" (114 mm) into standpipe.

Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. See Installation Instructions.

Ld (too long to drain water) appears in display

Washer taking too long to drain water. Drain extends more than 4.5" (114 mm) into standpipe.

Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Lower drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from drain hose. See Installation Instructions.

Fabric Damage (cont.)

Using single-dose laundry packet

Packet not dissolving. Make sure single-dose laundry packet is added to washer basket before adding clothes. Follow the manufacturers recommendations.

18

WHIRLPOOL CORPORATION LAUNDRY WARRANTYLIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter Whirlpool) will pay for Factory Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTYThis limited warranty does not cover:1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing. 3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage. 4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool. 5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase. 6. Pick up and delivery. This major appliance is intended to be repaired in your home. 7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance. 8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available. 9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool published installation instructions. 10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined. The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIESIMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGESYOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.If you think you need repair service, first see the Troubleshooting section of the Use & Care Guide. If you are unable to resolve the problem after checking Troubleshooting, additional help can be found by checking the Assistance or Service section or by calling Whirlpool. In the U.S.A., call 1 -800 -253-1301. In Canada, call 1-800 -807- 6777. 10/11

Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service.Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product.

Dealer name _________________________________________

Address _____________________________________________

Phone number _______________________________________

Model number _______________________________________

Serial number ________________________________________

Purchase date ________________________________________

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTYWhirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

19

SCURIT DE LA LAVEUSE

20

Dtection automatique de taille de charge

Une fois que lon dmarre le programme, le couvercle se verrouille et la laveuse entame un processus de dtection pour dterminer le niveau deau appropri la charge. Vous entendrez le moteur faire tourner le panier par de brefs mouvements dimpulsion pour bien imbiber la charge. Cette mthode de lavage avec faible consommation deau utilise moins deau et dnergie quune laveuse traditionnelle de type agitateur.

QUOI DE NEUF SOUS LE COUVERCLE?

Choix du dtergent appropriUtiliser uniquement des dtergents Haute efficacit. Lemballage portera la mention HE ou High Efficiency (haute efficacit). Un lavage avec faible consommation deau produit un excs de mousse avec un dtergent non HE ordinaire. Il est probable que lutilisation dun dtergent ordinaire prolongera la dure des programmes et rduira la performance de rinage. Ceci peut aussi entraner des dfaillances des composants et une moisissure perceptible. Les dtergents HE sont conus pour produire la quantit de mousse adquate pour le meilleur rendement. Suivre les recommandations du fabricant pour dterminer la quantit de dtergent utiliser.

Sons normaux prvisiblesAu cours des diffrents stades du programme de lavage, vous entendrez peut-tre des bruits que votre laveuse prcdente ne produisait pas. Par exemple, vous entendrez peut-tre un cliquetis au dbut du programme lorsque le systme de verrouillage du couvercle effectue un test automatique. On entendra diffrents bourdonnements et bruits de frottements rythmiques mesure que limpulseur dplace la charge. Parfois, il est possible que la laveuse soit compltement silencieuse, lorsquelle dtermine le niveau deau adquat ou quelle laisse tremper les vtements.

Utiliser uniquement un dtergent Haute efficacit (HE).

Nettoyage concentrLe systme de lavage faible consommation deau signifie un lavage concentr. Plutt que de diluer du dtergent comme dans une laveuse de type agitateur, cette laveuse libre le dtergent directement sur les endroits souills.

La nouveaut la plus remarquable de cette nouvelle laveuse est son systme de lavage faible consommation deau avec plateau de lavage. La laveuse ajuste automatiquement le niveau deau en fonction de la taille de la charge nul besoin de slecteur de niveau deau.

Charger les vtements sans les tasser et de faon uniforme le long du plateau de lavage. Ne pas placer les vtements directement au centre du plateau de lavage celui-ci doit tre visible.

mesure que la laveuse imbibe et dplace la charge, les vtements se tassent dans le panier. Ceci est normal et ne signifie pas que lon doive rajouter des vtements. IMPORTANT : Le panier de la laveuse ne sera pas rempli deau, comme avec votre prcdente laveuse de type agitateur. Il est normal quune partie de la charge dpasse du niveau deau.

Laver avec moins deau

Laveuse traditionnelle de type agitateur

Laveuse faible consommation deau

WashplateImpulseur

21

TABLEAU DE COMMANDE ET CARACTRISTIQUES

POWER BUTTON (Bouton de mise sous tension)Appuyer sur ce bouton pour METTRE EN MARCHE la laveuse. Si lon appuie une fois sur ce bouton alors que la laveuse fonctionne, le programme en cours est annul; si lon appuie deux fois dessus, la laveuse STEINT.

BOUTON DE PROGRAMME DE LAVAGETourner le bouton de programme de lavage pour slectionner un programme correspondant la charge de linge. Voir Guide de programmes pour des descriptions de programmes dtailles.

AFFICHAGE DE DURE/STATUTLaffichage de dure rsiduelle estime indique le temps ncessaire lachvement du programme. Des facteurs tels que la taille de la charge et la pression de leau peuvent affecter la dure affiche. La laveuse peut galement ajuster la dure du programme en cas de surcharge, de charge dsquilibre ou de production excessive de mousse.Si vous avez dfini un dpart diffr du cycle, lestime Affichage de duree restant indique le temps de retard rgl. Une fois le programme termin, le tmoin lumineux DONE (TERMIN) sallume jusqu ce que lon ouvre le couvercle.Ce tmoin lumineux indique que le couvercle est verrouill et ne peut tre ouvert. Si lon doit ouvrir le couvercle, appuyer sur START/PAUSE (MISE EN MARCHE/PAUSE). Le couvercle se dverrouille une fois que le mouvement de la laveuse a cess. Ceci peut prendre plusieurs minutes si la laveuse essorait la charge grande vitesse. Appuyer sur START/PAUSE (MISE EN MARCHE/PAUSE) pour redmarrer le programme.

ECO MONITOR (co-Moniteur)La laveuse est spcialement conue pour conomiser de leau et de lnergie. Chaque programme, ainsi que toute option slectionne, entranera une consommation dnergie et deau diffrente. Pour utiliser lco-moniteur, choisir le programme correspondant le mieux la charge laver puis ajuster les options de temprature et de vitesse dessorage pour amliorer la consommation nergtique de chaque programme.

START/PAUSE BUTTON (Bouton de mise en marche/pause)Appuyer sur ce bouton pour dmarrer le programme slectionn, puis appuyer de nouveau pour suspendre un programme.

1

2

3

CYCLE SIGNAL BUTTON (Bouton de signal de programme)Utiliser cette option pour ajuster le volume du signal qui retentit la fin dun programme. Un signal sonore plus fort peut tre utile si lon souhaite retirer les articles ds la fin du programme.

OPTIONS DES PROGRAMMES On peut aussi ajouter ou supprimer des options pour chaque programme. Noter que certaines options ne peuvent pas tre utilises avec certains programmes, et que certaines dentre elles sont prrgles pour ne fonctionner quavec certains programmes.

ECOBOOST (Puissance co)Loption EcoBoost (Puissance co) permet daccrotre vos conomies dnergie sur les programmes de lavage. Lorsque lon utilise cette option, le programme de lavage utilise une eau de lavage plus froide que celle du programme slectionn et peut augmenter la vitesse dessorage pour acclrer le schage.

EXTRA RINSE (Rinage supplmentaire)On peut utiliser cette option pour ajouter automatiquement un second rinage la plupart des programmes.

FABRIC SOFTENER DISPENSER SELECTOR (Slecteur de Distributeur dassouplissant pour tissu) Appuyer sur ce bouton pour que le distributeur dassouplissant pour tissu ajoute automatiquement de lassouplissant liquide la charge au moment opportun.

REGLAGS DES PROGRAMMESLorsquon slectionne un programme, ses rglages par dfaut sallument.

SOIL LEVEL (Niveau de salet)Le niveau de salet (dure de lavage) est prrgl pour chaque programme de lavage. Lorsque lon appuie sur la touche Soil Level (Niveau de salet), la dure du programme (en minutes) augmente ou diminue sur lafficheur de la dure rsiduelle estime et une dure de lavage diffrente apparat.Pour la plupart des charges, utiliser le niveau de salet prrgl pour le programme choisi. Pour les tissus trs sales et robustes, appuyer sur SOIL LEVEL (Niveau de salet) pour prolonger la dure de lavage si ncessaire. Pour les tissus peu sales et dlicats, appuyer sur SOIL LEVEL (Niveau de salet) pour abrger la dure de lavage si ncessaire. Un rglage de niveau de salet infrieur aidera rduire lemmlement et le froissement.

4

5

6

7

8

Certains programmes et caractristiques ne sont pas disponibles sur certains modles.

1 3 42 5 6

8 7

22

WASH TEMP (Temprature de lavage)La fonction de contrle de temprature dtecte et maintient une temprature uniforme de leau en rgulant le dbit darrive deau chaude et deau froide. Slectionner une temprature de lavage en fonction du type de tissu et de salet laver. Pour des rsultats optimaux, suivre les instructions sur ltiquette du vtement et utiliser la temprature deau de lavage la plus chaude possible qui reste sans danger pour le tissu. Les tempratures de leau tide et de leau chaude seront

infrieures celles de votre prcdente laveuse. Mme avec un rglage de lavage leau froide, il est

possible que de leau tide soit ajoute la laveuse pour maintenir une temprature minimale.

Distributeurs

Distributeur de dtergent Haute efficacit HEVerser le dtergent HE liquide ou en poudre ou le produit activateur Oxi dans ce distributeur pour le programme de lavage principal.

A B

CUtiliser uniquement un dtergent Haute efficacit (HE).

Distributeur dagent de blanchiment liquide Ce distributeur peut contenir jusqu 3/4 de tasse (180 mL) dagent de blanchiment. Lagent de blanchiment sera automatiquement dilu et distribu au moment opportun au cours du programme de lavage. Ce distributeur ne peut pas diluer de lagent de blanchiment en poudre.REMARQUE : Remplir le distributeur uniquement avec un agent de blanchiment liquide.

Distributeur dassouplissant de tissu liquideSi dsir, verser la mesure dassouplissant pour tissu liquide dans le distributeur dassouplissant pour tissu liquide. Celui-ci distribuera automatiquement le produit au moment opportun si lon slectionne loption dassouplissant pour tissu. Utiliser uniquement de lassouplissant de tissu liquide

dans ce distributeur.

A

C

B

SPIN SPEED (Vitesse dessorage)Cette laveuse slectionne automatiquement la vitesse dessorage en fonction du programme slectionn. Les vitesses prrgles peuvent tre modifies. Sur certains programmes, certaines vitesses dessorage ne sont pas disponibles. Des vitesses dessorage plus leves signifient des

dures de schage plus courtes mais elles peuvent augmenter le froissement de la charge.

Des vitesses dessorage plus lentes signifient moins de froissement mais laissent la charge plus humide.

23

GUIDE DE PROGRAMMES

Articles laver :

Programme : Temprature de lavage* :

Vitesse dessorage :

Niveau de

salet :

Options disponibles :

Dtails du programme :

Articles en soie lavables en machine, tissus lavables la main et laine

Handwash/ Delicate (Lavage

la main/ articles dlicats)

Vtements lgrement sales

Tissus non repassables

Quick Wash (Lavage rapide)

Perm Press/Casual

(Pressage permanent/ tout-aller)

Utiliser ce programme pour laver les articles dlicats lavables en machine. Ce programme utilise un culbutage intermittent dans de leau froide et un essorage faible vitesse pour prendre soin des articles dlicats lavables et viter le rtrcissement. Placer les petits articles dans des sacs en filet avant le lavage.

Utiliser ce programme pour laver des petites charges de 23 articles lgrement sales donton a besoin rapidement. Ce programme combine un culbutage vitesse rapide, une dure de lavage rduite et un essorage vitesse leve pour rduire la dure de schage.

Utiliser ce programme pour les vtements de travail peu sales. Ce programme utilise un lavage leau tide, une priode de refroidissement et des vitesses dessorage moyennes pour mieux lutter contre le froissement.

Draps normalement sales

Sheets (Draps)

Utiliser ce programme pour laver les draps de lit. Ce programme utilise de leau supplmentaire et une action de lavage spciale pour rduire lentortillement.

Les rglages et options indiqus en gras sont les rglages par dfaut pour ce programme. Pour un meilleur soin des tissus, choisir le programme qui convient le mieux la charge laver. Si lon utilise lco-moniteur, ajuster la temprature et la vitesse dessorage dans ce programme pour amliorer la consommation dnergie.Certains programmes et options ne sont pas disponibles sur certains modles.

Options de Temprature de lavage :Hot (Chaude)Warm (Tide)Cool (Fraiche)Cold (Froide)

Options de Vitesse dessorage : High (leve)Medium (Moyenne)Low (Basse) No Spin (Pas dessorage)

Options de Niveau de salet :Heavy (Intense)NormalMedium (Moyen)Light (Lger)

Options disponibles :Extra Rinse (Rinage supplmentaire)EcoBoost (Puissance co)Fabric Softener (Assouplissant pour tissu)

Utiliser ce programme pour nettoyer les articles en coton et les charges de tissus mixtes prsentant un degr de salet normal. Les rglages par dfaut peuvent tre ajusts au besoin.

NormalCharges de vtements en coton, lin et charges mixtes

Medium Low

Heavy Normal Medium

Light



Hot Warm Cool Cold

Hot Warm Cool Cold

High Medium

Low

High Medium

Low

Heavy Normal Medium

Light

Heavy Normal

Medium Light


Fabric Softener

Hot Warm Cool Cold

High Medium

Low

Heavy Normal

Medium Light


Fabric Softener

Hot Warm Cool Cold

High Medium

Heavy Normal** Medium

Light


Fabric Softener

Warm Cool Cold

Tissu et vtements de sport

Active Wear

(Vtements de sport)

Hot Warm Cool Cold

High Medium

Low

Heavy Normal

Medium Light

Utiliser ce programme pour laver des charges de pas-fer des tissus tels que des chandails sport et autres vtements de sport.


Fabric Softener

* Tempratures de lavage varie en fonction du rglage du cycle choisi. Tous les paramtres du cycle dutiliser un rinage froid la temprature.** Pas tous les modles par dfaut du rglage du niveau de salet. Certains modles par dfaut pour Medium sur ce cycle.

24

Articles laver :


Vitesse dessorage :

Niveau de

salet :



Tissus rsistants, articles grand-teint

Heavy Duty (Service intense)

Utiliser ce programme pour les articles en coton trs sales ou en coton pais. Ce programme combine un lavage vitesse rapide, une dure de lavage plus longue et un essorage vitesse trs leve pour rduire la dure de schage. Ajuster les rglages de temprature si ncessaire.

Articles de grande taille tels que les sacs de couchage, les petits duvets, les vestes

Bulky Items (Articles

volumineux)

Ce programme est conu pour les articles surdimensionns qui nabsorbent pas facilement leau, tels que les couettes, les oreillers et les vestes avec rembourrage en polyester. Ce programme utilise un trempage prliminaire pour bien imbiber larticle/les articles.

Whites (Blancs)

Ce programme introduit lagent de blanchiment liquide la charge au moment appropri pour un blanchiment amlior des tissus blancs sales.

GUIDE DE PROGRAMMESLes rglages et options indiqus en gras sont les rglages par dfaut pour ce programme. Pour un meilleur soin des tissus, choisir le programme qui convient le mieux la charge laver. Si lon utilise lco-moniteur, ajuster la temprature et la vitesse dessorage dans ce programme pour amliorer la consommation dnergie.Certains programmes et options ne sont pas disponibles sur certains modles.

Tissus blancs sales

Hot Warm Cool Cold

High Medium

Low

Heavy Normal Medium

Light


Fabric Softener

Hot Warm Cool Cold

Medium Low

Heavy Normal

Medium Light


Fabric Softener

Couleurs fonces, cotons,lin, casual etcharges mixtes

Cold Wash/ Clean Care

(Lavage froid/entretien

de nettoyage)

Cold High Medium

Low

Heavy Normal Medium

Light

Ce programme utilise leau de lavage froid et une solution de dtergent concentr pour soulever doucement les taches et les soins pour les tissus. Les rglages peuvent tre ajusts comme souhait, mais il doit utiliser seulement les paramtres de leau froide.


Fabric Softener

Hot Warm Cool Cold

HighMedium

Low

HeavyNormalMedium

Light


Fabric Softener

Pas de vtements dans la laveuse

Nettoyage de la laveuse avec affresh

(Clean Washer with affresh)

Utiliser ce programme lissue de chaque srie de 30 lavages pour que lintrieur de la laveuse reste frais et propre. Ce programme utilise un niveau deau plus lev. Avec ce programme, utiliser une tablette de nettoyant pour laveuse affresh ou de leau de Javel pour nettoyer soigneusement lintrieur de votre laveuse. Ce programme ne doit pas tre interrompu. Voir Entretien de la laveuse.IMPORTANT : Ne pas placer de vtements ou autres articles dans la laveuse pendant le programme Clean Washer with affresh. Utiliser ce programme avec une cuve de lavage vide.

EcoBoost





* Tempratures de lavage varie en fonction du rglage du cycle choisi. Tous les paramtres du cycle dutiliser un rinage froid la temprature.

25

Articles laver :


Vitesse dessorage :

Niveau de

salet :



Utiliser ce programme pour extraire par essorage lexcdent deau prsent dans une charge. Ce programme vacue leau et effectue un essorage haute vitesse. La vitesse dessorage est rglable.

Drain & Spin (Vidange et essorage)

Charge de vtements mouille

Maillots de bain et articles ncessitant uniquement un rinage

Rinse & Spin(Rinage et essorage)

Ce programme utilise une vitesse dessorage leve. Pour certains tissus, il peut tre judicieux de rgler la vitesse dssorage un rglage faible.

GUIDE DE PROGRAMMESLes rglages et options indiqus en gras sont les rglages par dfaut pour ce programme. Pour un meilleur soin des tissus, choisir le programme qui convient le mieux la charge laver. Si lon utilise lco-moniteur, ajuster la temprature et la vitesse dessorage dans ce programme pour amliorer la consommation dnergie.Certains programmes et options ne sont pas disponibles sur certains modles.

Pour les modles avec des positions de boutons de programme distinctes pour Rinse & Spin (rinage et essorage) et Drain & Spin (vidange et essorage) :

Maillots de bain et articles ncessitant uniquement un rinage

Rinse/Drain & Spin

(Rinage/ Vidange et essorage)

Charge de vtements mouille

Rinse/Drain & Spin

(Rinage/ Vidange et essorage)

Pour slectionner, choisir Rinse/Drain & Spin (Rinage/Vidange et essorage) et dsactiver Extra Rinse (Rinage supplmentaire). Utiliser ce programme pour extraire par essorage lexcdent deau prsent dans une charge. Ce programme vacue leau et effectue un essorage haute vitesse. La vitesse dessorage est rglable.

Pour les modles avec une position de bouton de programme Rinse/Drain & Spin (rinage/vidange et essorage) :

Ce programme utilise une vitesse dessorage leve. Pour certains tissus, il peut tre judicieux de rgler la vitesse dssorage un rglage faible.

HighMedium

Low

HighMedium

Low

HighMedium

Low

Utiliser ce programme pour faire tremper les petites taches tenaces sur les tissus. Une fois la dure expire, la laveuse vacue leau mais elle neffectue pas dessorage et un signal sonore retentit. Pour rgler un programme la suite dun autre, ajouter du dtergent et slectionner un programme en fonction du type de tissu.

Tissus trs sales

Soak (Trempage)

HighMedium

Low



Warm Cool Cold

Heavy Normal Medium

Light

EcoBoost





* Tempratures de lavage varie en fonction du rglage du cycle choisi. Tous les paramtres du cycle dutiliser un rinage froid la temprature.

26

UTILISATION DE LA LAVEUSE

Vider les poches. Des pices de monnaie, des boutons ou objets de petite taille sont susceptibles de glisser sous la plateau de lavage et de sy coincer, ce qui peut entrane des bruits inattendus.

Trier les articles en fonction du programme et de la temprature deau recommands, ainsi que de la solidit des teintures.

Sparer les articles trs sales des articles peu sales. Sparer les articles dlicats des tissus rsistants. Ne pas scher les vtements si les taches sont toujours

prsentes aprs le lavage car la chaleur pourrait fixer les taches sur le tissu.

Traiter les taches sans dlai. Fermer les fermetures glissire, attacher les crochets,

cordons et ceintures en tissu. ter les garnitures et les ornements non lavables.

Rparer les dchirures pour viter que les articles ne sendommagent encore davantage lors du lavage.

Conseils utiles : Lors du lavage darticles impermables ou rsistants

leau, charger la laveuse de faon uniforme. Voir Guide de programmes pour des conseils et pour plus dinformations sur lutilisation du programme Bulky Items (Articles volumineux).

1. Trier et prparer le linge Utiliser des sacs en filet pour aider empcher lemmlement

lors du lavage darticles dlicats ou de petits articles. Retourner les tricots pour viter le boulochage. Sparer

les articles qui forment la charpie de ceux qui la retiennent. Les articles synthtiques, tricots et articles en velours retiennent la charpie provenant des serviettes, des tapis et des tissus chenille.

REMARQUE : Toujours lire et suivre les instructions des tiquettes de soin des tissus pour viter dendommager les vtements.

On peut ajouter un sachet de lessive dose unique, lagent de blanchiment sans danger pour les couleurs, le produit Oxi ou des cristaux dassouplissant pour tissu dans le panier avant dajouter le linge.REMARQUE : Najoutez pas les vtements au panier de la laveuse avant dajouter des produits de buanderie. Suivez toujours les instructions du fabricant.

2. Ajouter un sachet de lessive dose unique, lagent de blanchiment sans danger pour les couleurs, le produit Oxi ou des cristaux dassouplissant pour tissu (si dsir).

27

Ajouter une mesure de dtergent HE dans le distributeur de dtergent. IMPORTANT : Utiliser uniquement des dtergents Haute efficacit. Lemballage portera la mention HE ou High Efficiency (Haute efficacit). Un lavage avec faible consommation deau produit un excs de mousse avec un dtergent non HE ordinaire. Il est probable que lutilisation dun dtergent ordinaire prolongera la dure des programmes et rduira la performance de rinage. Ceci peut aussi entraner des dfaillances des composants et une moisissure perceptible. Les dtergents HE sont conus pour produire la quantit de mousse adquate pour le meilleur rendement. Suivre les recommandations du fabricant pour dterminer la quantit de dtergent utiliser.REMARQUE : Si lon utilise un produit activateur pour vtements Oxi, lajouter au distributeur de dtergent.CONSEIL UTILE : Voir Entretien de la laveuse pour plus dinformation sur la mthode recommande pour le nettoyage des distributeurs de la laveuse.

4. Verser le dtergent HE dans le distributeur

Distributeur de dtergent

3. Charger les vtements dans la laveuse

Charger les vtements sans les tasser et de faon uniforme le long du plateau de lavage. Ne pas placer les vtements directement au centre du plateau de lavage celui-ci doit tre visible. Essayer de mlanger diffrents types darticles pour rduire lemmlement. IMPORTANT : Les articles doivent pouvoir se dplacer librement pour un nettoyage optimal et pour rduire le froissement et lemmlement.

REMARQUE: Ne pas ajouter de sachet de lessive dose unique, dagent de blanchiment sans danger pour les couleurs, des activateurs de type Oxi ou des cristaux dassouplissant pour tissu dans les distributeurs. Ils ne seront pas distribus correctement.

5. Ajouter lagent de blanchiment liquide dans le distributeur

Ne pas remplir excessivement le distributeur, diluer le produit ou utiliser plus de 3/4 de tasse (180 mL). Ne pas utiliser dagent de blanchiment sans danger pour les couleurs ni de produit Oxi en mme temps que le programme utilisant de lagent de blanchiment liquide.

Agent de blanchiment liquide

Verser une mesure dassouplissant pour tissu liquide dans le distributeur, toujours suivre les instructions du fabricant concernant la dose dassouplissant pour tissu utiliser en fonction de la taille de la charge. Slectionner ensuite loption Fabric Softener (Assouplissant pour tissu). IMPORTANT : Loption Fabric Softener doit tre slectionne pour que le produit soit distribu correctement et au moment adquat du programme. Ne pas remplir le distributeur excessivement ni diluer le produit. Si lon remplit excessivement le distributeur, lassouplissant pour tissu sera distribu dans la laveuse immdiatement.Si lon slectionne loption Extra Rinse (Rinage supplmentaire), lassouplissant de tissu sera distribu au cours du dernier rinage.

REMARQUE : Ne pas utiliser de boules distributrices dassouplissant pour tissu dans cette laveuse. Elles ne distribueront pas leur contenu correctement.

6. Verser de lassouplissant pour tissu liquide dans le distributeur

Verser de lassouplissant pour tissu dans le distributeur

28

Tourner le bouton de programme pour choisir un programme de lavage. Le tmoin Estimated Time Remaining (Dure rsiduelle estime) sallume, et la dure du programme saffiche. On peut remarquer un ajustement de la dure durant le programme. Ceci est normal.Si lon ne souhaite pas dmarrer un programme immdiatement, on peut choisir loption DELAY WASH (LAVAGE DIFFR).

Pour choisir une heure de lavage diffr :1. Appuyer sur le bouton DELAY WASH (LAVAGE DIFFR)

pour slectionner le dlai souhait.2. Appuyer sur START/PAUSE (MISE EN MARCHE/PAUSE)

pour lancer le compte rebours. Le compte rebours commence aprs que le tmoin lumineux START/PAUSE (MISE EN MARCHE/PAUSE) a arrt de clignoter.

Pour annuler un programme diffr :1. Appuyer de nouveau sur START/PAUSE (MISE EN

MARCHE/PAUSE) pour dmarrer un programme de lavage immdiatement.

IMPORTANT : Lorsque lon utilise un programme diffr, utiliser uniquement du dtergent HE liquide dans le distributeur. Les dtergents en poudre peuvent absorber lhumidit dun programme prcdent et former des grumeaux avant que le programme de lavage ne commence.

8. Slectionner le programme

9. Slectionner les rglages de programme, si dsir

Aprs avoir slectionn un programme, les rglages par dfaut correspondant ce programme sallument. Appuyer sur les boutons de rglage du programme pour modifier le niveau de salet, la vitesse dessorage et la temprature de lavage, si dsir. Tous les rglages ne sont pas disponibles avec tous les programmes.REMARQUE : Toujours lire et suivre les instructions des tiquettes de soin des tissus pour viter dendommager les vtements.

Tissus suggrs

Blancs et couleurs clairesVtements robustesSalet intense

Wash Temp (Temprature de lavage)

Hot (Chaude) De leau froide est ajoute pour conomiser de lnergie. Ceci sera plus froid que le rglage du chauffe-eau pour leau chaude de votre domicile.

Warm (Tide) De leau froide sera ajoute; il est donc possible que leau soit plus froide que celle que fournissait votre laveuse prcdente.

Cool (Frache) De leau chaude est ajoute pour favoriser llimination de la salet et pour aider dissoudre les dtergents.

Cold (Froide) De leau tide est ajoute pour favoriser llimination de la salet et aider dissoudre les dtergents.

Couleurs vivesSalet modre lgre

Couleurs qui dteignent ou sattnuentSalet lgre

Couleurs fonces qui dteignent ou sattnuentSalet lgre

7. Appuyer sur POWER pour mettre la laveuse en marche

29

11. Appuyer sans relcher sur START/PAUSE (MISE EN MARCHE/PAUSE) pour dmarrer le programme de lavage

10. Slectionner les options de programme

Slectionner les autres options de programme que lon souhaite ajouter, si ce nest pas dj fait. Certains programmes ajoutent automatiquement certaines options telles que Extra Rinse (Rinage supplmentaire). Elles peuvent tre dsactives si dsir.

REMARQUE : Toutes les options ne sont pas disponibles avec tous les programmes.

Appuyer sur le bouton START/PAUSE (MISE EN MARCHE/PAUSE) pour dmarrer le programme de lavage. Lorsque le programme est termin, le tmoin lumineux DONE (TERMIN) sallume et le signal de fin de programme retentit (si activ). Retirer rapidement les vtements une fois le programme termin pour empcher la formation dodeurs, rduire le froissement et empcher les crochets mtalliques, fermetures glissire et boutons-pression de rouiller.

Dverrouiller le couvercle pour ajouter les vtementsSi lon doit ouvrir le couvercle pour ajouter 1 ou 2 vtements:Appuyer sur START/PAUSE (MISE EN MARCHE/PAUSE); le couvercle se dverrouille une fois que le mouvement de la laveuse a cess. Ceci peut prendre plusieurs minutes si la laveuse essorait la charge grande vitesse. Fermer ensuite le couvercle et appuyer de nouveau sur START/PAUSE (MISE EN MARCHE/PAUSE) pour redmarrer le programme.Si on laisse le couvercle ouvert pendant plus de 10 minutes, leau est vidange.

30

ENTRETIEN DE LA LAVEUSE

Remplacer les tuyaux darrive deau aprs 5 ans dutilisation pour rduire le risque de dfaillance intempestive. Inspecter priodiquement les tuyaux; les remplacer en cas de renflement, de dformation, de coupure et dusure ou si une fuite se manifeste.Lorsque vous remplacez les tuyaux darrive deau, noter la date de remplacement au marqueur indlbile sur ltiquette.REMARQUE : Cette laveuse ne comprend pas de tuyaux darrive deau. Voir les Instructions dinstallation pour plus de renseignements

TUYAUX DARRIVE DEAU

ENTRETIEN DE LA LAVEUSERecommandations pour une laveuse propre et pour un niveau de performance optimal1. Toujours utiliser des dtergents haute efficacit (HE) et suivre

les recommandations du fabricant de dtergent HE pour dterminer la quantit de dtergent HE utiliser. Ne jamais utiliser plus que la quantit recommande de dtergent, car ceci peut augmenter le taux daccumulation de rsidus de dtergent et de souillures lintrieur de la laveuse, ce qui pourrait entraner la formation dodeurs indsirables.

2. Excuter priodiquement des lavages avec de leau tide ou chaude (et non pas exclusivement des lavages leau froide), car leau tide ou chaude permet de contrler plus efficacement la vitesse laquelle les salets et les rsidus de dtergent saccumulent.

3. Veiller toujours laisser le couvercle de la laveuse ouvert entre deux utilisations pour quelle puisse scher, et pour viter laccumulation de rsidus gnrateurs dodeurs.

Nettoyage de la laveuse chargement par le dessusLire compltement ces instructions avant dentreprendre les oprations de nettoyage de routine recommandes ci-dessous. Le processus dentretien de la laveuse doit tre excut au moins une fois par mois ou intervalles de 30 lavages (selon la priode la plus courte des deux); ceci permettra de contrler la vitesse laquelle les rsidus de dtergent et les souillures saccumulent dans la laveuse.Nettoyage de lintrieur de la laveusePour que lintrieur de la laveuse reste libre de toute odeur, suivre les instructions dutilisation indiques ci-dessus et effectuer la procdure de nettoyage mensuelle recommande suivante :Programme Clean Washer (nettoyage de la laveuse)Cette laveuse comporte un programme spcial qui utilise un volume deau plus important en conjonction avec le nettoyant pour laveuse affresh ou un agent de blanchiment liquide au chlore pour nettoyer lintrieur de la laveuse.Dbut de la procdure1. Procdure de nettoyage avec le nettoyant pour laveuse

affresh (recommand pour une performance optimale) : a. Ouvrir le couvercle de la laveuse et retirer tout vtement

ou article. b. Placer une pastille de nettoyant pour laveuse affresh

dans le fond du panier de la laveuse. c. Ne pas placer de pastille de nettoyant pour laveuse

affresh dans le distributeur dtergent. d. Ne pas ajouter de dtergent ou autre compos chimique

dans la laveuse lors de lexcution de cette procdure. e. Rabattre le couvercle de la laveuse. f. Slectionner le programme CLEAN WASHER (nettoyage

de la laveuse). g. Appuyer sur le bouton START/PAUSE (mise en marche/

pause) pour dmarrer le programme. Le processus du programme de nettoyage de la laveuse est dcrit ci-dessous.

ENTRETIEN DE LA LAVEUSE (suite) REMARQUE : Pour de meilleurs rsultats, ne pas interrompre

le programme. Si lon doit interrompre le programme, appuyer sur POWER/CANCEL (mise sous tension/annulation). (Pour les modles dpourvus du bouton Power/Cancel [mise sous tension/annulation], appuyer sur START/PAUSE [mise en marche/pause] pendant trois secondes). Une fois le programme de nettoyage de la laveuse termin, effectuer un programme Rinse/Drain & Spin (Rinage/vidange et essorage) pour rincer le nettoyant de la laveuse.

2. Mthode avec agent de blanchiment au chlore (autre option) : a. Ouvrir le couvercle de la laveuse et retirer tout vtement

ou article. b. Verser 1 tasse (236 mL) dagent de blanchiment liquide au chlore dans le distributeur dagent de blanchiment. REMARQUE : Lemploi dune quantit dagent de blanchiment liquide au chlore suprieure ce qui est recommand ci-dessus pourrait endommager la laveuse avec le temps. c. Rabattre le couvercle de la laveuse. d. Ne pas ajouter de dtergent ou autre compos chimique

dans la laveuse lors de lexcution de cette procdure. e. Slectionner le programme CLEAN WASHER (nettoyage

de la laveuse). f. Appuyer sur le bouton START/PAUSE (mise en marche/

pause) pour dmarrer le programme. Le processus du programme de nettoyage de la laveuse est dcrit ci-dessous.

REMARQUE : Pour de meilleurs rsultats, ne pas interrompre le programme. Si lon doit annuler le programme, appuyer sur POWER/CANCEL (mise sous tension/annulation). (Pour les modles dpourvus du bouton Power/Cancel [mise sous tension/annulation], appuyer sur START/PAUSE [mise en marche/pause] pendant trois secondes). Une fois le programme de nettoyage de la laveuse termin, effectuer un programme Rinse/Drain & Spin (Rinage/vidange et essorage) pour rincer le nettoyant de la laveuse.

Description de lutilisation du programme de nettoyage de la laveuse :1. Ce programme remplit la laveuse un niveau suprieur

celui des programmes de lavage ordinaires afin que le niveau de leau de rinage soit suprieur celui dun programme de lavage ordinaire.

2. Ce programme comporte une agitation et un essorage pour amliorer llimination des souillures.

Une fois ce programme termin, laisser le couvercle ouvert pour permettre une meilleure ventilation et pour que lintrieur de la laveuse puisse scher.

Nettoyage des distributeursAprs avoir utilis la laveuse pendant longtemps, on peut parfois constater une accumulation de rsidus dans les distributeurs de la laveuse. Pour liminer les rsidus des distributeurs, les essuyer avec un chiffon humide et les scher avec une serv

Documents

cabrio---washer