L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. B4A

Classified by UL as equipment grounding conductors per NEC 392.7.

B4A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayB4A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.00 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 4.12” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

B4A 12 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

B4

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

120 = 10’144 = 12’

ORDERING DATA EXAMPLE:

NEMA Load Class: 16B / 12C CSA Load Class: D1-3m

POWER-TRAY RAIL DATA RAIL TYPE: B4A

SPAN (ft) 6 8 10 12 14 16

MAX LOAD (lbs/ft) 487 284 181 126 93 71

DEFLECTION MULTIPLIER 0.001 0.003 0.008 0.016 0.030 0.052LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 4.12”Load Depth: 3.05”

4.12"

3.06" TRAY WIDTH

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO.ML4A

Classified by UL as equipment grounding conductors per NEC 392.7.

ML4A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayML4A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: .60 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 3.95” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

ML4 A 12 - 24 - 144

ORDERING DATA EXAMPLE:

TRAY WIDTH

NEMA Load Class: 8B CSA Load Class: 123 kg/m 3.7

co

nn

ecto

r

Siderail: 3.95”Load Depth: 3.08”

LoA

D c

HA

rt*

rUnG SPAce

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

ML4

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

trAYLenGtH

144 = 12’

PoWer-trAY rAIL DAtA rAIL tYPe: ML4A

SPAN (ft) 6 8 10 12

MAX LOAD (lbs/ft) 200 113 81 76

DEFLECTION MULTIPLIER 0.0015 0.0047 0.011 0.024

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO.MB4A

Classified by UL as equipment grounding conductors per NEC 392.7.

MB4A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayMB4A Series Cable Tray / Ladder / Aluminum

1/2RUNG

SPACING

RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.50 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 4.18” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

MB4 A 06 - 24 - 144

ORDERING DATA EXAMPLE:

NEMA Load Class: 20A CSA Load Class: E-3m

co

nn

ecto

r

Siderail: 4.18”Load Depth: 3.08”

LoA

D c

HA

rt*

rUnG SPAce

06 = 6”09 = 9”12 = 12”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

MB4

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

trAYLenGtH

144 = 12’240 = 20’

PoWer-trAY rAIL DAtA rAIL tYPe: MB4A

SPAN (ft) 10 12 14 16 18 20

MAX LOAD (lbs/ft) 224 156 114 88 69 56

DEFLECTION MULTIPLIER 0.006 0.012 0.022 0.038 0.061 0.093

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. L7A

Classified by UL as equipment grounding conductors per NEC 392.7.

L7A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayL7A Series Cable Tray / Ladder / Aluminum

1/2RUNG

SPACING

RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 0.60 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 7.5” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

L7A 06 - 24 - 144

ORDERING DATA EXAMPLE:

7.50" 6.41"

.75"

TRAY WIDTH

NEMA Load Class: 12B CSA Load Class: 182 kg/m 3.7m

co

nn

ecto

r

Siderail: 7.50”Load Depth: 6.48”

PoWer-trAY rAIL DAtA rAIL tYPe: L7A

SPAN (ft) 6 8 10 12

MAX LOAD (lbs/ft) 209 123 89 77

DEFLECTION MULTIPLIER 0.0047 0.012 0.026 0.029LoA

D c

HA

rt*

rUnG SPAce

06 = 6”09 = 9”12 = 12”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

L7

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

trAYLenGtH

144 = 12’

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. L6A

Classified by UL as equipment grounding conductors per NEC 392.7.

L6A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayL6A Series Cable Tray / Ladder / Aluminum

1/2RUNG

SPACING

RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 0.60 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 5.88” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

L6A 06 - 24 - 144

ORDERING DATA EXAMPLE:

NEMA Load Class: 12B CSA Load Class: 162 kg/m 3.7m

co

nn

ecto

r

Siderail: 5.88”Load Depth: 5.02”

PoWer-trAY rAIL DAtA rAIL tYPe: L6A

SPAN (ft) 6 8 10 12

MAX LOAD (lbs/ft) 207 123 89 77

DEFLECTION MULTIPLIER 0.0047 0.012 0.026 0.029LoA

D c

HA

rt*

rUnG SPAce

06 = 6”09 = 9”12 = 12”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

L6

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

trAYLenGtH

144 = 12’

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. L5A

Classified by UL as equipment grounding conductors per NEC 392.7.

L5A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayL5A Series Cable Tray / Ladder / Aluminum

1/2RUNG

SPACING

RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 0.60 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 5.88” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

L5A 06 - 24 - 144

ORDERING DATA EXAMPLE:

NEMA Load Class: 12B CSA Load Class: 121 kg/m 3.7m

co

nn

ecto

r

Siderail: 4.88”Load Depth: 4.02”

PoWer-trAY rAIL DAtA rAIL tYPe: L5A

SPAN (ft) 6 8 10 12

MAX LOAD (lbs/ft) 205 123 89 75

DEFLECTION MULTIPLIER 0.0047 0.012 0.026 0.029LoA

D c

HA

rt*

rUnG SPAce

06 = 6”09 = 9”12 = 12”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

L5

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

trAYLenGtH

144 = 12’

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. L4A

Classified by UL as equipment grounding conductors per NEC 392.7.

L4A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayL4A Series Cable Tray / Ladder / Aluminum

1/2RUNG

SPACING

RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 0.40 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 3.88” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

L4A 06 - 24 - 144

ORDERING DATA EXAMPLE:

NEMA Load Class: 8B CSA Load Class: N/A

co

nn

ecto

r

Siderail: 3.88”Load Depth: 3.02”

PoWer-trAY rAIL DAtA rAIL tYPe: L4A

SPAN (ft) 6 8 10 12

MAX LOAD (lbs/ft) 135 76 44 27

DEFLECTION MULTIPLIER 0.002 0.006 0.015 0.032LoA

D c

HA

rt*

.75"

3.88" 2.97" TRAY WIDTH

rUnG SPAce

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MAterIAL

A = ALuMINuM 6063 - T6 ALLOY

rAIL SerIeS

L4

trAY WIDtH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

trAYLenGtH

144 = 12’

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. F8A

Classified by UL as equipment grounding conductors per NEC 392.7.

F8A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayF8A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 2.00 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 8” High Ladder, Aluminum, 09” Rung Spacing, 24” Wide, 30’ Long

F8A 09 - 24 - 360RUNG SPACE

09 = 9” 12 = 12”

MATERIAL

A = Aluminum 6063 - T6 Alloy

RAIL SERIES

F8

TRAY WIDTH

12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

TRAYLENGTH

360 = 30ft.300 = 25ft.

ORDERING DATA EXAMPLE:

NEMA Load Class: 20C + CSA Load Class: 240 kg/m 9.1m

POWER-TRAY RAIL DATA RAIL TYPE: F8A

SPAN (ft) 20 22 24 26 28 30 40

MAX LOAD (lbs/ft) 363 300 252 215 185 161 101

DEFLECTION MULTIPLIER 0.007 0.0010 0.013 0.019 0.025 0.033 0.146 LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 8.00”Load Depth: 6.18”

18"

7.25"

3/8” ALUMINUM

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. E7A

Classified by UL as equipment grounding conductors per NEC 392.7.

E7A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayE7A Series Cable Tray / Ladder / Aluminum

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 2.00 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 7.40” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 30’ Long

E7A 12 - 24 - 360RUNG SPACE

09 = 9” 12 = 12”

RAIL SERIES

E7A = 7.40” 6063 -T6 Aluminum

TRAY WIDTH

12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”

TRAYLENGTH

300 = 25ft.360 = 30ft.

ORDERING DATA EXAMPLE:

NEMA Load Class: 20C + CSA Load Class: 152 kg/m 9.1m

Co

NN

ECTo

R

Siderail: 7.40”Load Depth: 6.23”

PoWER-TRAY RAIL DATA RAIL TYPE: E7A

SPAN (ft) 20 22 24 26 28 30

MAX LOAD (lbs/ft) 232 192 161 136 117 102

DEFLECTION MULTIPLIER 0.011 0.016 0.023 0.031 0.042 0.055LoA

D C

HA

RT*

TRAY WIDTH 7.40"

2"

6.24"

BUFFALO OFFICE: CORPORATE OFFICE:180 HOPKINS STREET

BUFFALO, NEW YORK 14220 PHONE: (716) 821-1344

FAX: (716) 821-1345

4 INTERNATIONAL DRIVERYEBROOK, NEW YORK 10573

PHONE: (914) 934-2075FAX: (914) 934-2190

NOTES:UNLESS NOTED, DRAWING UNITS ARE IN INCH.1.PARTS TO BE COMERICALLY CLEAN AND FREE OF BURRS, SCRATCHES & OIL.2.

PROJECT/JOB NAME HERE

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MONOSYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MONOSYSTEMS INC. IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

MATERIAL: 6063-T6

DRAWN BY

CHECKED BY

DATENAME

DRAWING TITLE:

SIZE

BPART NUMBER: REV

EST. WEIGHT (LBS): 1.01 SCALE: 6:8

AJJB

* *

02/11/13

MID-SPAN SPLICE PLATES

SHEET 1 OF 1

AX-2012

PROJECT:

BUFFALO OFFICE: CORPORATE OFFICE:180 HOPKINS STREET

BUFFALO, NEW YORK 14220 PHONE: (716) 821-1344

FAX: (716) 821-1345

4 INTERNATIONAL DRIVERYEBROOK, NEW YORK 10573

PHONE: (914) 934-2075FAX: (914) 934-2190

NOTES:UNLESS NOTED, DRAWING UNITS ARE IN INCH.1.PARTS TO BE COMERICALLY CLEAN AND FREE OF BURRS, SCRATCHES & OIL.2.

PROJECT/JOB NAME HERE

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MONOSYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MONOSYSTEMS INC. IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

MATERIAL: 6063-T6

DRAWN BY

CHECKED BY

DATENAME

DRAWING TITLE:

SIZE

BPART NUMBER: REV

EST. WEIGHT (LBS): 1.01 SCALE: 6:8

AJJB

* *

02/11/13

MID-SPAN SPLICE PLATES

SHEET 1 OF 1

AX-2012

PROJECT:

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. D6A

Classified by UL as equipment grounding conductors per NEC 392.7.

D6A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayD6A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.50 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 6.20” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

D6A 06 - 24 - 144 RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

D6

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20C CSA Load Class: E-6m

POWER-TRAY RAIL DATA RAIL TYPE: D6A

SPAN (ft) 14 16 18 20 24

MAX LOAD (lbs/ft) 210 161 127 103 72

DEFLECTION MULTIPLIER 0.0071 0.012 0.019 0.030 0.061 LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 6.19”Load Depth: 5.08”

6.20" 5.10"

2"

TRAY WIDTH

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. C6A

Classified by UL as equipment grounding conductors per NEC 392.7.

C6A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayC6A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.50 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 6.17” High Ladder, Aluminum, 06” Rung Spacing, 24” Wide, 12’ Long

C6A 06 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

C6

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’288 = 24’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20B/16C CSA Load Class: E-6m

POWER-TRAY RAIL DATA RAIL TYPE: C6A

SPAN (ft) 12 14 16 18 20 24

MAX LOAD (lbs/ft) 233 171 131 104 84 69

DEFLECTION MULTIPLIER 0.0043 0.008 0.014 0.022 0.033 0.049LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 6.17”Load Depth: 5.06”

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. C5A

Classified by UL as equipment grounding conductors per NEC 392.7.

C5A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayC5A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.50 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 5.06” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

C5A 12 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

C5

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20B/16C CSA Load Class: E-3m

POWER-TRAY RAIL DATA RAIL TYPE: C5A

SPAN (ft) 10 12 14 16 18 20

MAX LOAD (lbs/ft) 310 215 158 121 96 77

DEFLECTION MULTIPLIER 0.0035 0.0079 0.014 0.023 0.037 0.057LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 5.06”Load Depth: 3.96”

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. C4A

Classified by UL as equipment grounding conductors per NEC 392.7.

C4A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayC4A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.50 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 4.21” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

C4A 12 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

C4

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20B/16C CSA Load Class: E-6m

POWER-TRAY RAIL DATA RAIL TYPE: C4A

SPAN (ft) 10 12 14 16 18 20

MAX LOAD (lbs/ft) 320 222 163 125 99 80

DEFLECTION MULTIPLIER 0.005 0.009 0.017 0.030 0.047 0.072LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 4.20”Load Depth: 3.08”

TRAY WIDTH

TRAY WIDTH

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. B6A

Classified by UL as equipment grounding conductors per NEC 392.7.

B6A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayB6A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.00 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 6.12” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

B6A 12 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

B6

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20A/16B CSA Load Class: D1-6m

POWER-TRAY RAIL DATA RAIL TYPE: B6A

SPAN (ft) 10 12 14 16 18 20

MAX LOAD (lbs/ft) 204 142 104 80 63 51

DEFLECTION MULTIPLIER 0.0028 0.006 0.011 0.019 0.03 0.045LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 6.12”Load Depth: 5.04”

TRAY WIDTH

TRAY WIDTH

L

4 International Drive Rye Brook, NY 10573

Toll Free: 1 888.764.7681Phone: 914.934.2075

Fax: 914.934.2190MonoSystems.com

1/2013 DOCUMENT REF. NO. B5A

Classified by UL as equipment grounding conductors per NEC 392.7.

B5A/Straight SectionManufactured in the USA by MonoSystems, Inc.

™PowerTrayB5A Series Cable Tray / Ladder / Aluminum

RUNGSPACING

1/2 RUNGSPACING

General InformationTRAY DESIGN: Construction and markings are per the latest edition of NEMA Standards Pub. VE1, CSA C22.2 No. 126.

TRAY GROUNDING CAPABILITY: Classified as an equipment grounding conductor per N.E.C. 392.7 with a maximum 1600 ampere rating. UL Cross Sectional area: 1.00 in2

CONNECTORS: Supplied in pairs with hardware. Splice resistance is less than 0.00033 ohms. Standard hardware: 3/8 in. cadmium-plated with clear zinc topcoat. Stainless steel hardware is available upon request.

MonoSystems trays marked with CSA load class have been tested (loading, finish and electrical) by UL to CSA standard 126 22.2

Material: Aluminum 6063-T6 Alloy

* Values are based on simple beam tests per NEMA VE 1 on 36” wide cable tray with rungs spaced on 12” centers. Cable trays will support, without collapse, a 200 lb. (90.7 kg) concentrated load over and above published loads. Published load safety factor is 1.5.

To convert 1.5 safety factor to 2.0, multiply the published load by 0.75. To obtain mid-span deflection, multiply a load by the deflection multiplier. Cable tray must be supported on spans shorter than or equal to the length of the cable tray being installed. Individual rungs will support without collapse a 200 lb. (90.7 kg) concentrated load applied at the mid-span of the rung, over and above the NEMA rated cable load with a 1.5 safety factor for highlighted NEMA spans and loads.

Power-Tray, 5” High Ladder, Aluminum, 12” Rung Spacing, 24” Wide, 12’ Long

B5 A 12 - 24 - 144RUNG SPACE

06 = 6”09 = 9”12 = 12”18 = 18”04 = VENTEDSB = SOLID BOTTOM

MATERIAL

A = ALuMINuM 6063 - T6 ALLOY

RAIL SERIES

B5

TRAY WIDTH

06 - 6”09 = 9”12 = 12”18 = 18”24 = 24”30 = 30”36 = 36”42 = 42”

TRAYLENGTH

144 = 12’240 = 20’

ORDERING DATA EXAMPLE:

NEMA Load Class: 20A/12C CSA Load Class: D1-6m

POWER-TRAY RAIL DATA RAIL TYPE: B5A

SPAN (ft) 10 12 14 16 18 20

MAX LOAD (lbs/ft) 200 139 102 78 62 50

DEFLECTION MULTIPLIER 0.0049 0.010 0.019 0.032 0.051 0.078LOA

D C

HA

RT*

CO

NN

ECTO

R

Siderail: 5.00”Load Depth: 3.93”