BUSHTON MANUFACTURING HAWK ustom Knife Department here at ushton Manufacturing. ... 680 ft of shoe @ $ .82 $ 557.60 ... Gives a finished appearance to square or flat edge

To Order Call: 620-562-3557 or e-mail: [email protected] 1

BUSHTON MANUFACTURING Makers of

Since 1929

To Order Call 620-562-3557 or e-mail at [email protected] Catalog M-1 January 2013

STOCK AND CUSTOM MOLDING KNIFE CATALOG A MOLDING KNIFE FOR EVERY NEED


MOLDING KNIVES With the HAWK Multi-Function Planer you can start your own successful business in which you design and create your own custom molding or recreate historic antique moldings. You can do it easily and affordably with a little help from the HAWK Custom Knife Department here at Bushton Manufacturing. We have a large catalog of standard molding knifes. We can also supply custom molding knives upon request. Signed copy of all custom knife quotes is required with payment before a custom knife can be made. Sharpening template is supplied with all custom knife orders. All custom molding knives must be paid for before the knife is cut and are non refundable. Knives are priced per knife, gibs and balances are separately priced. Knife orders take about 1 week after they are paid for.


FOR THE EXAMPLE SHOWN TO THE RIGHT. IF SIMPLE STOCK MOLDINGS FROM A NATIONAL LUMBER YARD CHAIN ARE USE. 874 ft of casing @ $1.14 $ 992.94 680 Ft of base @ $1.19 $ 809.20 226 ft of chair rail @ $1.88 $ 406.80 430 ft of crown molding @ $1.74 $ 748.20 680 ft of shoe @ $ .82 $ 557.60 TOTAL $3514.74 OR YOU COULD BUY ROUGH CUT LUMBER 682 Board ft @ $1.10 $ 750.20 WHICH GIVES YOU A SAVINGS OF $ 2764.54 IN JUST ONE JOB USING ONLY STOCK MOLDINGS. IF YOU WANT TO USE ANTIQUE MOLDINGS AND A MULTI-PIECE CROWN MOLDING YOUR SAV-INGS WILL BE MUCH HIGHER. YOUR SAVINGS COULD BE A MUCH AS 3 TIME MORE.

CUSTOM AND STANDARD MOLDING KNIVES AND HOLDERS


ANTIQUE MOLDINGS. Moldings designed to resemble the older, late 19th and early 20th century moldings. Used for house molding, trim and decoration. Also used as picture frames etc.

BACK BANDS. Used as a cap on plywood, or shelves and corner edge covers.

BACK RELIEF KNIFE. Used to cut up to ¼ of an inch deep on the back of moldings to allow them to set up against the wall tighter.

BAR RAIL. Used for the edge rail of a bar.

BASE CAP. Use by itself for decoration or in combination with other moldings. Gives a finished appearance to square or flat edge.

BASE MOLDING. Used to conceal joints at the junction of wall and floor, picture frames, decorative trim for furniture, doors, etc.

BATTEN. Can be used with other moldings to enhance the décor.

BEDS. Used as top decorative trim the top of furniture or cabinets.

BENCH SLATS. Knives to cut molding for use as slats for outdoor furni-ture such as benches and chairs.

BRICK MOLDING. Primarily used as outside window and door trim.

CAP MOLDINGS. Used as a cap on plywood, or shelves and corner edge covers.

CASING. Used to conceal joints around windows and doors, picture frames and accent room design.

CHAIR RAIL. Used around the wall to style and keep chairs from hitting the wall. Placed about 30 to 36 inches off the floor. Also used as picture frames.

CHAMFER STRIP. Used as an inside corner and a glue board for 45 de-gree angles.

CORNER GAURDS. Used to cover outside corners, along shelf edges and corners of furniture.

COVES. Used to conceal joints at the junction of wall and floor, picture frames, decorative trim for furniture, doors, etc.

CROWNS. Used in covering wall to ceiling joints, picture frames and other decorative uses. Can be used independently or in combination with other moldings such as stops or half rounds.

DRIP CAPS. Used at the top of windows and doors to keep moisture from getting in the walls.

EDGE KNIFE. Used to cut the edge off of a board up to 1 inch thick.

GLASS BEAD. This type of molding is used to hold glass in place in a door. It is also used to decorate inside corners.

HANDRAIL. Used as hand-holds on stairs and along .ledges.

INSIDE CORNER. To cover the crack of an inside corner, ceiling to wall and other 90 degree corner areas.

LATTICE. Used to produce square cornered boards to be used along with other moldings to trim or by itself to make such things as trellis, slats and guides.

LOG CABIN SIDING. Knives for cutting log cabin siding.

MANTEL MOLDING. Knives for cutting molding designed especially for mantels.

PANEL MOLDING. Used to cover joints in paneling, picture frames, and to decorate and style.

PARTING CUT. Knives used to cut boards in two up to ¾ of an inch thick.

PICTURE MOLDING. Used as picture frames. Attached to a wall to hang pictures from using a hook over frame. Also used with other moldings to decorate.

QUARTER ROUNDS. Used in many areas to cover inside corners. Yields good coverage over rough contours.

RABBET CUT. Knives used to cut various depths to 1 inch deep and 1 inch wide.

ROSETTE CUTTERS. For cutting rosettes for the corners of windows and doors. Also used for making wheels for toys.

ROUNDS. Used as rods, dowels and support rods such as closet rods.

SCREEN MOLDING. Yields a decorative finished edge to any exposed edge.

SHELF CLEAT. Used to hold a board for a shelf.

SHELF EDGE. For the front edge of shelves. Gives a decorative finish to any exposed edge.

SHINGLE/PANEL MOLDING. Used to hide panel joints and to add deco-ration.

SPECIAL CUSTOM MOLDING KNIVES. We can make special molding knives from either samples or scale drawings. The limiting factors are maximum knife height and machine power.

SQUARES. Used to produce square cornered boards to be used along with other moldings to trim or by itself to make such things as trellis, slats and guides.

S4S (SQUARE 4 SIDES). Used to produce square cornered boards to be used along with other moldings to trim or by itself to make such things as trellis, slats and guides.

STOPS. Used in door jams to keep te door from swinging through the opening and windows to hold the window in place.

TONGUE AND GROOVE. For cutting tongue and groove.

WHEEL CUTTER. For cutting wooden wheels.

MOLDING DEFINNITIONS


CROWN 1/4" FB 1/4" CB 5/16" CB PRICE

WM-048 BK 904-0480 914-0480 934-0480 $ 105.00

WM-048 TK 904-0481 914-0481 934-0481 $ 105.00


WM-049 BK 904-0490 914-0490 934-0490 $ 92.50

WM-049 TK 094-0491 914-0491 934-0491 $ 92.50


WM-051 BK 904-0510 914-0510 934-0510 $ 85.00

WM-051 TK 904-0511 914-0511 934-0511 $ 85.00


WM-052 BK 904-0520 914-0520 934-0520 $ 75.00

WM-052 TK 904-0521 914-0521 934-0521 $ 75.00


WM-053 BK 904-0530 914-0530 934-0530 $ 72.50

WM-053 TK 904-0531 914-0531 934-0531 $ 72.50


WM-054 BK 904-0540 914-0540 934-0540 $ 65.00

WM-054 TK 904-0541 914-0541 934-0541 $ 65.00

CROWN MOLDINGS


WM-047 BK 904-0470 914-0470 934-0470 $ 112.50

WM-047 TK 904-0471 914-0471 934-0471 $ 112.50


WM-057 BK 904-0570 914-0570 934-0570 $ 85.00

WM-057 TK 904-0571 914-0571 934-0571 $ 85.00


WM-058 BK 904-0580 914-0580 934-0580 $ 75.00

WM-058 TK 904-0581 914-0581 934-0581 $ 75.00


WM-059 BK 904-0590 914-0590 934-0590 $ 65.00

WM-059 TK 904-0591 914-0591 934-0591 $ 65.00


WM-060 BK 904-0600 914-0600 934-0600 $ 55.00

WM-060 TK 904-0601 914-0601 934-0601 $ 55.00


WM-067 BK 904-0670 914-0670 934-0670 $ 65.00

WM-067 TK 904-0671 914-0671 934-0671 $ 65.00


WM-068 BK 904-0680 914-0680 934-0680 $ 52.50

WM-068 TK 904-0681 914-0681 934-0681 $ 52.50


BED 1/4" FB 1/4" CB 5/16" CB PRICE

WM-070 BK 904-0700 914-0700 934-0700 $ 75.00

WM-070 TK 904-0701 914-0701 934-0701 $ 75.00


WM-072 BK 904-0720 914-0720 934-0720 $ 65.00

WM-072 TK 904-0721 914-0721 934-0721 $ 65.00


WM-074 BK 904-0740 914-0740 934-0740 $ 55.00

WM-074 TK 904-0741 914-0741 934-0741 $ 55.00

BEDS

CORNER GUARDS

CORNER GUARD# 1/4" FB 1/4" CB 5/16" CB PRICE WM-199 TK 904-1991 914-1990 934-1991 $ 40.00

WM-200 TK 904-2001 914-2001 934-2001 $ 35.00

WM-201 TK 904-2011 914-2011 934-2011 $ 46.25

WM-202 TK 904-2021 914-2021 934-2021 $ 42.50

WM-203 TK 904-2031 914-2031 934-2031 $ 35.00

WM-204 904-2041 914-2041 934-2041 $ 46.25

WM-205 TK 904-2051 914-2051 934-2051 $ 42.50

WM-206 904-2061 914-2061 934-2061 $ 35.00

SHINGLE, PANEL MOLDINGS

DRIP CAPS

DRIP CAP# 1/4" FB 1/4" CB 5/16" CB PRICE

WM-187 BK 904-1870 914-1870 934-1870 $ 60.00

WM-187 TK 904-1871 914-1871 934-1871 $ 60.00

WM-188 BK 904-1880 914-1880 934-1880 $ 52.50

WM-188 TK 904-1881 914-1881 934-1881 $ 52.50

WM-196 BK 904-1960 914-1960 934-1960 $ 55.00

WM-196 TK 904-1961 914-1960 934-1961 $ 55.00

WM-197 BK 904-1970 914-1970 934-1970 $ 52.50

WM-197 TK 904-1971 914-1971 934-1971 $ 52.50


WM-075 BK 904-0750 914-0750 934-0750 $ 52.50

WM-075 TK 904-0751 914-0751 934-0751 $ 52.50

WM-076 BK 904-0760 914-0760 934-0760 $ 50.00

WM-076 TK 904-0761 914-0761 934-0761 $ 50.00

PANEL 1/4" FB 1/4" CB 5/16" CB PRICE

WM-207 904-2070 914-2070 934-2070 $ 70.00

WM-209 904-2090 914-2090 934-2090 $ 60.00

WM-210 904-2100 914-2100 934-2100 $ 52.50

WM-212 904-2120 914-2120 934-2120 $ 70.00

WM-213 904-2130 914-2130 934-2130 $ 60.00

WM-217 904-2170 914-2170 934-2170 $ 55.00


BASE SHOE # 1/4" FB 1/4" CB 5/16" CB PRICE

WM-126 904-1260 914-1260 934-1260 $ 35.00

WM-127 904-1270 914-1270 934-1270 $ 35.00

WM-129 904-1290 914-1290 934-1290 $ 33.75

WM-129 3 UP 904-1293 914-1293 934-1293 $ 73.75

WM-131 904-1310 914-1310 934-1310 $ 35.00

WM-131 4 UP 904-1314 914-1314 934-1314 $ 95.00

GLASS BEAD # 1/4" FB 1/4" CB 5/16" CB PRICE

WM-147 904-1470 914-1470 934-1440 $ 31.25

WM-148 904-1480 914-1480 934-1480 $ 27.50

WM-081 BK 904-0810 914-0810 934-0810 $ 85.00

WM-081 TK 904-0811 914-0811 934-0811 $ 85.00

COVES # 1/4" FB 1/4" CB 5/16" CB PRICE

WM-082 BK 904-0820 914-0820 934-0820 $ 75.00

WM-082 TK 904-0821 914-0821 934-0821 $ 75.00








WM-084 BK 904-0840 914-0840 934-0840 $ 65.00

WM-084 TK 904-0841 914-0841 934-0841 $ 65.00

WM-085 BK 904-0850 914-0850 934-0850 $ 55.00

WM-085 TK 904-0851 914-0851 934-0851 $ 55.00

WM-086 BK 904-0860 914-0860 934-0860 $ 52.50

WM-086 TK 904-0861 914-0861 934-0861 $ 52.50

WM-089 BK 904-0890 914-0890 934-0890 $ 60.00

WM-089 TK 904-0891 914-0891 934-0891 $ 60.00

WM-090 1 UP 904-0900 914-0900 934-0900 $ 42.50

WM-090 2 UP 904-0901 914-0901 934-0901 $ 62.00

WM-092 1 UP 904-0920 914-0920 934-0920 $ 37.00

WM-092 2 UP 904-0921 914-0921 934-0921 $ 57.00


WM-093 1 UP 904-0930 914-0930 934-0930 $ 35.00

WM-093 2 UP 904-0931 914-0931 934-0931 $ 55.00

WM-093 3 UP 904-0932 914-0932 934-0932 $ 85.00

WM-094 904-0940 914-0940 934-0940 $ 42.50

WM-095 904-0950 914-0950 934-0950 $ 37.50

WM-096 1 UP 904-0960 914-0960 934-0960 $ 35.00

WM-096 2 UP 904-0961 914-0961 934-0961 $ 55.00

WM-100 904-1000 914-1000 934-1000 $ 33.75

WM-101 1 UP 904-1010 914-1010 934-1010 $ 30.00

WM-101 2 UP 904-1011 914-1011 934-1011 $ 50.00



WM-103 1 UP 904-1030 914-1030 934-1030 $ 41.25

WM-103 2 UP 904-1031 914-1031 934-1031 $ 61.25

WM-104 BK 904-1040 914-1040 934-1040 $ 47.00

WM-104 TK 904-1041 914-1041 934-1041 $ 47.50

WM-105 1 UP 904-1051 914-1051 934-1051 $ 35.00

WM-105 2 UP 904-1052 914-1052 934-1052 $ 55.00

WM-105 3 UP 904-1053 914-1053 934-1053 $ 75.00

WM-105 4 UP 904-1054 914-1054 934-1054 $ 95.00

QUARTER ROUND# 1/4" FB 1/4" CB 5/16" CB PRICE

WM-106 904-1060 914-1060 934-1060 $ 33.75

WM-107 904-1070 914-1070 934-1070 $ 32.00

WM-108 904-1080 914-1080 934-1080 $ 30.00

WM-108 2 UP 904-1082 914-1082 934-1082 $ 50.00

WM-109 904-1090 914-1090 934-1090 $ 27.50

WM109 4 UP 904-1094 914-1094 934-1094 $ 87.50

WM-110 904-1100 914-1100 934-1100 $ 25.00

WM-120 904-1200 914-1200 934-1200 $ 40.00

QUARTER ROUNDS

HALF ROUNDS (ALSO MAKE ROUNDS)

WM-120 904-1200 914-1200 934-1200 $ 40.00

WM-122 904-1220 914-1220 934-1220 $ 33.75

WM-123 904-1230 914.-1230 934-1230 $ 32.50

WM-124 904-1240 914-1240 934-1240 $ 30.00

WM-125 904-1250 914-1250 934-1250 $ 27.50

FLAT ASTRAGALS

WM-133 904-1330 914-1330 934-1330 $ 55.00

WM-134 904-1340 914-1340 934-1340 $ 47.50

WM-135 904-1350 914-1350 934-1350 $ 35.00

FLAT ASTRAGEL# 1/4" FB 1/4" CB 5/16" CB PRICE

QUARTER ROUND# 1/4" FB 1/4" CB 5/16" CB PRICE

SHELF EDGE & SCREEN MOLDINGS

WM-137 904-1370 914-1370 934-1370 $ 35.00

WM-138 904-1380 914-1380 934-1380 $ 32.50

WM-140 904-1400 914-1400 934-1400 $ 35.00

WM-141 904-1410 914-1410 934-1410 $ 32.50

WM-142 904-1420 914-1420 934-1420 $ 35.00

WM-144 904-1440 914-1440 934-1440 $ 35.00

MOLDING # 1/4" FB 1/4" CB 5/16" CB PRICE

HALF ROUND# 1/4" FB 1/4" CB 5/16" CB PRICE

BASE CAPS

BASE CAP # 1/4" FB 1/4" CB 5/16" CB PRICE WM-163 1 UP 904-1630 914-1630 934-1630 $47.50

WM-163 2 UP 904-1631 914-1631 934-1631 $67.50

WM-164 1 UP 904-1640 914-1640 934-1640 $42.00

WM-164 2 UP 904-1642 914-1642 934-1642 $62.50

WM-166 904-1660 914-1660 934-1660 $45.00

WM-167 904-1670 914-1670 934-1670 $42.50

WM-172 904-1720 914-1720 934-1720 $35.00

BRICK MOLDING


WM-182 904-1820 914-1820 934-1820 $ 52.50

WM-183 904-1830 914-1830 934-1830 $ 42.50

WM-185 904-1850 914-1850 934-1850 $ 47.50

WM-186 904-1860 914-1860 934-1860 $ 40.00

WM-175 904-1750 914-1750 934-1750 $ 60.00

WM-176 904-1760 914-1760 934-1760 $ 55.00

WM-180 904-1800 914-1800 934-1800 $ 60.00



WAINSCOT-PLY CAP MOLDING

CAP MOLDING 1/4" FB 1/4" CB 5/16" CB PRICE

WM-290 904-2900 914-2900 934-2900 $ 47.50

WM-292 904-2920 914-2900 934-2920 $ 42.50

WM-294 904-2940 914-2900 934-2940 $ 42.50

WM-295 904-2950 914-2950 934-2950 $ 45.00

WM-296 904-2960 914-2960 934-2960 $ 35.00

BATTENS

BACK BANDS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-280 TK 904-2801 914-2800 934-2801 $ 42.50

WM-281 BK 904-2810 914-2810 934-2810 $ 42.50

WM-281 TK 904-2811 914-2811 934-2811 $ 42.50

BATTENS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-224 TK 904-2241 914-2241 934-2241 $ 65.00

WM-229 BK 904-2290 914-2290 934-2290 $ 52.50

WM-229 TK 904-2291 914-2294 934-2291 $ 52.50

Tongue and groove cuts are made by using guides to hold the board on

Tongue and Groove

1/4" FB 1/4" CB 5/16" CB PRICE

CK-389 2" GROOVE 906-9200 916-9200 936-9200 $ 60.00

CK-389 2" TONGUE 906-9250 916-9250 936-9250 $ 60.00

CK-390 1" TONGUE 907-1500 917-1500 937-1500 $ 40.00

CK-390 1" GROOVE 907-1501 917-1501 937-1501 $ 40.00

CK-391 1" TONGUE 907-1600 917-1600 937-1600 $ 40.00

CK-391 1" GROOVE 907-1601 917-1601 937-1601 $ 40.00

CK-392 1" GROOVE 907-1700 917-1700 937-1700 $ 40.00

CK-392 1" TONGUE 907-1701 917-1701 937-1701 $ 40.00

BMF-001 TONGUE 907-1800 917-1800 937-1800 $ 40.00

BMF-001 GROOVE 907-1801 917-1801 937-1801 $ 40.00

BMF-001 FLOORING TONGUE AND GROOVE

BARRAIL

BARRAIL 1/4" FB 1/4" CB 5/16" CB

BMB-001T 907-1900 917-1900 937-1900

BMB-001B 907-1901 917-1901 937-1901


HAND RAILS

HAND RAIL 1/4" FB 1/4" CB 5/16" CB PRICE

WM-230 BK 904-2300 914-2300 934-2300 $ 53.75

WM-230 TK 904-2301 914-2301 934-2301 $ 53.75

WM-231 BK 904-2310 914-2310 934-2310 $ 53.75

WM-231 TK 904-2311 914-2311 934-2311 $ 53.75

WM-240 BK 904-2400 914-2400 934-2400 $ 65.00

WM-240 TK 904-2401 914-2401 934-2401 $ 65.00

ROUNDS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-232 904-2320 914-2320 934-2320 $ 52.50

WM-233 904-2330 914-2330 934-2330 $ 46.25

WM-234 904-2340 914-2340 934-2340 $ 53.75

CK-403 907-0403 917-0403 937-0403 $ 35.00

CK-404 904-0404 917-0404 937-0404 $ 37.50

CK-405 907-0405 917-0405 937-0405 $ 47.50

SQUARE 1/4" FB 1/4" CB 5/16" CB PRICE

WM-236 904-2360 914-2360 934-2360 $ 52.50

WM-237 904-2370 914-2370 934-2370 $ 46.25

WM-238 904-2380 914-2380 934-2380 $ 41.25

WM-239 904-2390 914-2380 934-2390 $ 35.00

S4S STOCK 1/4" FB 1/4" CB 5/16" CB PRICE

WM-241 904-2410 914-2410 934-2410 $ 75.00

WM-243 904-2430 914-2430 934-2430 $ 55.00

WM-246 904-2460 914-2460 934-2460 $ 75.00

WM-247 904-2470 914-2470 934-2470 $ 60.00

WM-248 904-2480 914-2480 934-2480 $ 55.00

WM-249 904-2490 914-2490 934-2490 $ 52.50

WM-250 904-2500 914-2500 934-2500 $ 50.00

WM-251 904-2510 914-2510 934-2510 $ 47.50

WM-252 904-2520 914-2520 934-2520 $ 45.00

WM-254 904-2540 914-2540 934-2540 $ 35.00


LATICE 1/4" FB 1/4" CB 5/16" CB PRICE

WM-265 904-2650 914-2650 934-2650 $ 55.00

WM-266 904-2660 914-2650 934-2660 $ 52.50

WM-267 904-2670 914-2670 934-2670 $ 47.50

WM-268 904-2680 914-2680 934-2680 $ 42.00

CHAIR RAILS

CHAIR RAILS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-297 904-2970 914-2970 934-2970 $ 80.00

WM-298 904-2980 914-2980 934-2980 $ 70.00

WM-300 904-3000 914-3000 934-3000 $ 80.00

WM-303 904-3030 914-3030 934-3030 $ 70.00

WM-304 904-3040 914-3040 934-3040 $ 65.00

PANEL STRIPS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-955 904-9550 914-9550 934-9550 $ 65.00

WM-956 904-9560 914-9560 934-9560 $ 60.00

WM-957 904-9570 914-9560 934-9570 $ 55.00

WM-960 904-9600 914-9600 934-9600 $ 65.00

WM-962 904-9620 914-9620 934-9620 $ 60.00

WM-963 904-9630 914-9630 934-9630 $ 55.00

WM-965 904-9650 914-9650 934-9650 $ 65.00

WM-967 904-9670 914-9670 934-9670 $ 60.00

WM-968 904-9680 914-9680 934-9680 $ 55.00

WM-970 904-9700 914-9700 934-9700 $ 65.00

WM-972 904-9720 914-9720 934-9720 $ 60.00

WM-973 904-9730 914-9730 934-9730 $ 55.00

WM-975 904-9750 914-9750 934-9750 $ 65.00

WM-977 904-9770 914-9770 934-9770 $ 60.00

WM-978 904-9780 914-9780 934-9780 $ 55.00

WM-980 904-9800 914-9800 934-9800 $ 65.00

WM-982 904-9820 914-9820 934-9820 $ 60.00

WM-983 904-9830 914-9830 934-9830 $ 55.00

WM-985 904-9850 914-9850 934-9850 $ 65.00

WM-987 904-9870 914-9870 934-9870 $ 60.00

WM-988 914-9880 914-9880 934-9880 $ 55.00

PANEL STRIPS MULLION CASINGS


CASING

CASING 1/4" FB 1/4" CB 5/16" CB PRICE

WM-306 904-3060 914-3060 934-3060 $ 65.00

WM-307 904-3070 914-3070 934-3070 $ 65.00

WM-315 904-3150 914-3150 934-3150 $ 70.00

WM-316 904-3160 914-3160 934-3160 $ 65.00

WM-321 904-3210 914-3210 934-3210 $ 65.00

WM-324 904-3240 914-3240 934-3240 $ 65.00

WM-327 1 UP 904-3270 914-3270 934-3270 $ 65.00

WM-327 2 UP 904-3271 914-3271 934-3271 $ 85.00

WM-328 904-3280 914-3280 934-3280 $ 65.00

WM-329 904-3290 914-3290 934-3290 $ 65.00

WM-330 904-3300 914-3300 934-3300 $ 65.00

WM-332 904-3320 914-3320 934-3320 $ 65.00


WM-346 904-3460 914-3460 934-3460 $65.00

WM-351 904-3510 914-3510 934-3510 $70.00

WM-356 904-3560 914-3560 934-3560 $65.00

WM-361 904-3610 914-3610 934-3610 $70.00

WM-366 904-3660 914-3660 934-3660 $65.00

WM-371 904-3710 914-3710 934-3710 $70.00

WM-376 904-3760 914-3760 934-3760 $65.00

WM-387 904-3870 914-3870 934-3870 $65.00

WM-390 904-3900 914-3900 934-3900 $72.50

WM-440 904-4400 914-4400 934-4400 $70.00

WM-442 904-4420 914-4420 934-4450 $65.00



WM-408 904-4080 914-4080 934-4080 $ 115.00

WM-410 904-4100 914-4100 934-4100 $ 105.00

WM-412 904-4120 914-4120 934-4120 $ 90.00

WM-413 904-4130 914-4120 934-4130 $ 85.00

WM-452 904-4520 914-4520 934-4520 $ 70.00

WM-453 904-4530 914-4530 934-4530 $ 65.00


WM-444 904-4440 914-4440 934-4440 $ 90.00

WM-445 904-4450 914-4450 934-4450 $ 85.00

WM-448 904-4480 914-4480 934-4480 $ 90.00

WM-683 904-6830 914-6830 934-6830 $ 90.00

WM-790 904-7901 914-7901 934-7901 $ 65.00

WM-791 904-7911 914-7911 934-7911 $ 65.00

WM-795 904-7950 914-7950 934-7950 $ 65.00


WM-658 904-6580 914-6580 934-6580 $ 125.00

WM-660 904-6600 914-6600 934-6600 $ 105.00

WM-662 904-6620 914-6620 934-6620 $ 90.00

WM-663 904-6630 914-6630 934-6630 $ 85.00

WM-664 904-6640 914-6640 934-6640 $ 80.00

WM-683 904-6830 914-6830 934-6830 $ 90.00

WM-709 904-7090 914-7090 934-7090 $ 110.00

WM-710 904-7100 914-7100 934-7100 $ 105.00

WM-712 904-7120 914-7120 934-7120 $ 90.00

WM-713 904-7130 914-7130 934-7130 $ 85.00

WM-714 904-7140 914-7140 934-7140 $ 80.00

WM-722 904-7220 914-7220 934-7220 $ 90.00

WM-723 904-7230 914-7230 934-7230 $ 85.00

WM-724 904-7240 914-7240 934-7240 $ 80.00

WM-725 904-7250 914-7250 934-7250 $ 70.00

WM-726 904-7260 914-7260 934-7260 $ 65.00

WM-750 904-7500 914-7500 934-7500 $ 105.00

WM-752 904-7520 914-7520 934-7520 $ 90.00

WM-753 904-7530 914-7530 934-7530 $ 85.00


STOPS

Shading indicates the example pictured

CASING DIMENSIONS 1/4" FB 1/4" CB 5/16" CB PRICE WM-813 7/16" X 2-1/4" 904-8130 914-8130 934-8130 $65.00

WM-814 7/16" X 1-3/4" 904-8140 914-8140 934-8140 $55.00

WM-815 7/16" X 1-5/8" 904-8150 914-8150 934-8150 $52.50

WM-816 7/16" X 1-3/8" 904-8160 914-8160 934-8150 $47.50

WM-817 7/16" X 1-1/4" 904-8170 914-8170 934-8170 $45.00

WM-818 7/16" X 1-1/8" 904-8180 914-8180 934-8180 $42.50

WM-820 7/16" X 7/8" 904-8200 914-8200 934-8200 $37.50

WM-831 3/8 X 3/4" 904-8310 914-8310 934-8310 $35.00

CASING DIMENSIONS 1/4" FB 1/4" CB 5/16" CB PRICE

WM-843 7/16" X 2-1/4" 904-8430 914-8430 934-8430 $65.00

WM-844 7/16" X 1-3/4" 904-8440 914-8430 934-8440 $55.00

WM-845 7/16" X 1-5/8" 904-8450 914-8450 934-8450 $52.50

WM-846 7/16" X 1-3/8" 904-8460 914-8460 934-8460 $47.50

WM-847 7/16" X 1-1/4" 904-8470 914-8470 934-8470 $45.00

WM-848 7/16" X 1-1/8" 904-8480 914-8480 934-8480 $42.50

WM-850 7/16" X 7/8" 904-8500 914-8500 934-8500 $37.00

WM-851 7/16" X 3/4" 904-8510 914-8510 934-8510 $35.00


WM-853 3/8" X 2-1/4" 904-8530 914-8530 934-8530 $65.00

WM-854 3/8" X 1-3/4" 904-8540 914-8540 934-8540 $55.00

WM-855 3/8" X 1-5/8" 904-8550 914-8550 934-8550 $52.50

WM-856 3/8" X 1-3/8" 904-8560 914-8560 934-8560 $47.50

WM-857 3/8" X 1-1/4" 904-8570 914-8570 934-8570 $45.00

WM-858 3/8" X 1-1/8" 904-8580 914-8570 934-8580 $42.50

WM-860 3/8" X 7/8" 904-8600 914-8600 934-8600 $37.50

WM-861 3/8" X 3/4" 904-8610 914-8610 934-8600 $35.00


WM-873 7/16" X 2-1/4" 904-8730 914-8730 934-8730 $65.00

WM-874 7/16" X 1-3/4" 904-8740 914-8740 934-8740 $55.00

WM-875 7/16" X 1-5/8" 904-8750 914-8750 934-8750 $52.50

WM-876 7/16" X 1-3/8" 904-8760 914-8760 934-8760 $47.50

WM-877 7/16" X 1-1/4" 904-8770 914-8770 934-8770 $45.00

WM-878 7/16" X 1-1/8" 904-8780 914-8780 934-8770 $42.50

WM-880 7/16" X 7/8" 904-8800 914-8800 934-8800 $37.50

WM-881 7/16" X 3/4" 904-8810 914-8810 934-8810 $35.00


WM-903 7/16" x 2-1/4" 904-9030 914-9030 934-9030 $65.00

WM-904 7/16" X 1-3/4" 904-9040 914-9040 934-9040 $55.00

WM-905 7/16" X 1-5/8" 904-9050 914-9050 934-9050 $52.50

WM-906 7/16" X 1-3/8" 904-9060 914-9060 934-9060 $47.50

WM-907 7/16" X 1-1/4" 904-9070 914-9070 934-9070 $45.00

WM-908 7/16" X 1-1/8" 904-9080 914-9080 934-9080 $42.50

WM-910 7/16" X 7/8" 904-9100 914-9100 934-9100 $37.50

WM-911 7/16" X 3/4" 904-9110 914-9110 934-9110 $35.00


WM-913 3/8" X 2-1/4" 904-9130 914-913 934-9130 $65.00

WM-914 3/8" X 1-3/4" 904-9140 914-9140 934-9140 $55.00

WM-915 3/8" X 1-5/8" 904-9150 914-9150 934-9150 $52.50

WM-916 3/8" X 1-3/8" 904-9160 914-9160 934-9160 $47.50

WM-917 3/8" X 1-1/4" 904-9170 914-9170 934-9170 $45.00

WM-918 3/8" X 1-1/8" 904-9180 914-9180 934-9180 $42.50

WM-920 3/8" X 7/8" 904-9200 914-9180 934-9200 $37.50

WM-921 3/8" X 3/4" 904-9210 914-9210 934-9210 $35.00


WM-933 7/16" X 2-1/4" 904-9330 914-9330 934-9330 $65.00

WM-934 7/16" X 1-3/4" 904-9340 914-9340 934-9340 $55.00

WM-935 7/16" X 1-5/8" 904-9350 914-9350 934-9350 $52.50

WM-936 7/16" X 1-3/8" 904-9360 914-9360 934-9360 $47.50

WM-937 7/16" X 1-1/4" 904-9370 914-9360 934-9370 $45.00

WM-938 7/16" X 1-1/8" 904-9380 914-9380 934-9380 $42.50

WM-940 7/16" X 7/8" 940-9400 914-9400 934-9400 $37.50

WM-941 7/16" X 3/4" 904-9410 914-9410 934-9410 $35.00


WM-943 3/8" X 2-1/4" 904-9430 914-9430 934-9430 $65.00

WM-944 3/8" X 1-3/4" 904-9440 914-9440 934-9440 $55.00

WM-945 3/8" X 1-5/8" 904-9450 914-9450 934-9450 $52.50

WM-946 3/8" X 1-3/8" 904-9460 914-9460 934-9460 $47.50

WM-947 3/8" X 1-1/4" 904-9470 914-9470 934-9470 $45.00

WM-948 3/8" X 1-1/8" 904-9480 914-9480 934-9480 $42.50

WM-950 3/8" X 7/8" 904-9500 914-9500 934-9500 $37.50

WM-951 3/8" X 3/4" 904-9510 914-9510 934-9510 $35.00


STOPS (CONT.)


WM-953 904-9530 914-9530 934-9530 $ 28.75


WM-954 904-9540 914-9540 934-9540 $ 27.50

SHELF CLEAT


WM-990 904-9900 914-9900 934-9900 $ 50.00

CHAMFER STRIP


WM-995 904-9950 914-9950 934-9950 $ 30.00

INSIDE CORNER


WM-999 BK 904-9990 914-9990 934-9990 $ 40.00

WM-999 TK 904-9991 914-9991 934-9991 $ 40.00

CASING TO MATCH ROSETTE PATTERNS


CK-409 907-0409 917-0409 937-0409 $ 90.00

CK-410 907-0410 917-0410 937-0410 $ 72.50

CK-411 907-0411 917-0411 937-0411 $ 80.00


CK-415 907-0415 917-0415 937-0415 $ 85.00

CK-416 907-0416 917-0416 937-0416 $ 100.00

CK-417 907-0417 917-0417 937-0417 $ 80.00

BEADED CASING

FLUTED CASING


CK-412 907-0412 917-0412 937-0412 $ 80.00

CK-413 907-0413 917-0413 937-0413 $ 85.00

CK-414 907-0414 917-0414 937-0414 $ 80.00

LOG CABIN SIDING (SHOWN HALF SCALE)


CK-418 907-0418 917-0418 937-0418 $ 130.00

CK-419 907-0419 917-0419 937-0419 $ 150.00

CK-420 907-0420 917-0420 937-0420 $ 170.00


MANTEL MOLD BENCH SLAT


CK-421 907-0421 917-0421 937-0421 $ 75.00


CK-422 907-0422 917-0422 937-0422 $ 52.50

MOLDING 1/4" FB 1/4" CB 5/16" CB PRICE

ANT-02 905-7020 915-7020 935-7020 $ 135.00


ANT-03 905-7030 915-7030 935-7030 $ 125.00


ANT-04 905-7040 915-7040 935-7040 $ 125.00


ANT-05 905-7050 915-7050 935-7050 $ 115.00


ANT-06 905-7060 915-7060 935-7060 $ 115.00


ANT-07 905-7070 915-7070 935-7070 $ 105.00

ANTIQUE MOLDING


ANT-01 905-7010 915-7010 935-7010 $ 125.00



ANT-08 905-7080 915-7080 935-7080 $ 105.00

ANTIQUE MOLDING


ANT-09 905-7090 915-7090 935-7090 $ 105.00


ANT-10 905-7100 915-7100 935-7100 $ 85.00


ANT-11 905-7110 915-7110 935-7110 $ 75.00


ANT-12 BK 905-7120 915-7120 935-7120 $75.00

ANT-12 TK 905-7121 915-7121 935-7121 $105.00


ANT-13 905-7130 915-7130 935-7130 $ 95.00


ANT-14 905-7140 915-7140 935-7140 $ 95.00


ANT-15 905-7150 915-7150 935-7150 $ 95.00


ANT-16 905-7160 915-7150 935-7160 $ 85.00


ANT-18 BK 905-7180 915-7180 935-7180 $95.00

ANT-18 TK 905-7181 915-7181 935-7181 $95.00


ANT-19 BK 905-7190 915-7190 935-7190 $ 95.00

ANT-19 TK 905-7191 915-7191 935-7191 $ 86.71


ANT-17 905-7170 915-7170 935-7170 $ 95.00


PICTURE FRAME MOLDINGS


WM-273 TK 904-2731 914-2731 934-2731 $ 55.00

WM-273 BK 904-2730 914-2730 934-2730 $ 55.00


WM-278 TK 904-2781 914-2781 934-2781 $ 55.00

WM-278 BK 904-2780 914-2780 934-2780 $ 55.00


PIC-01 905-8010 915-8010 935-8010 $ 70.84


PIC-02 905-8020 915-8020 935-8020 $ 70.84


PIC-03 905-8030 915-8030 935-8030 $ 70.84


PIC-04 905-8040 915-8040 935-8040 $ 70.84


PIC-05 905-8050 915-8050 935-8050 $ 63.94


PIC-06 905-8060 915-8060 935-8060 $ 75.90


PIC-07 905-8070 915-8070 935-8070 $ 75.90


PIC-08 905-8080 915-8070 935-8080 $ 75.90


PIC-09 905-8090 915-8090 935-8090 $ 93.66


PIC-10 905-8100 915-8100 935-8100 $70.84


PICTURE FRAME MOLDINGS (continued)


PIC-11 905-8110 915-8110 935-8110 $ 70.84


PIC-12 905-8120 915-8120 935-8120 $ 70.84


PIC-13 905-8130 915-8130 935-8130 $ 74.63


PIC-14 905-8140 915-7140 935-8140 $ 67.05


PIC-15 905-8150 915-8150 935-8150 $ 90.51

PIC-16 905-8160 915-8160 935-8160 $ 70.84

PIC-17 905-8170 915-8170 935-8170 $ 61.41


PIC-18 905-8180 915-8180 935-8180 $61.41


PIC-19 BK 905-8190 915-8190 935-8190 $ 67.05

PIC-19 TK 905-8191 915-8191 935-8191 $ 74.63


PIC-20 BK 905-8200 915-8200 935-8200 $ 69.58

PIC-20 TK 905-8201 915-8201 935-8201 $ 81.65


PIC-21 905-8210 915-8210 935-8210 $ 61.41


PIC-22 905-8220 915-8220 935-8220 $ 70.84


PIC-23 905-8230 915-8230 935-8230 $ 70.84


PIC-24 905-8240 915-8240 935-8240 $ 70.84


PICTURE FRAME MOLDINGS (continued)


PIC-25 905-8250 915-8250 935-8250 $ 70.84


PIC-26 905-8260 915-8260 935-8260 $ 70.84


PIC-27 BK 905-8270 915-8270 935-8270 $ 67.05

PIC-27 TK 905-8271 915-8270 935-8271 $ 67.05


PIC-28 905-8280 915-8280 935-8280 $ 67.05


PIC-29 905-8290 915-8290 935-8290 $ 67.05


PIC-30 905-8300 915-8300 935-8300 $ 67.05


PIC-31 905-8310 915-8310 935-8310 $ 67.05


PIC-32 905-8320 915-8320 935-8320 $ 67.05

BOTTOM KNIFE PART NUMBERS ARE 919-AHLL WHERE A IS: 1 FOR 1/4” FB 2 FOR 1/4” CB 3 FOR 5/16” CB WHERE H IS THE HEIGHT OF THE KNIFE IN QUARTER INCHES 1-1/2” is 6/4” which makes H = 6 2-1/4” is 9/4” which makes H = 9 WHERE LL IS THELENGTH OF THE KNIFE IN QUARTER INCHES 2-3/4” is 11/4” which makes LL = 11 1-1/4” is 5/4 “ which makes LL = 05

BOTTOM KNIVES

LL

H

BLADE HEIGHT 1/4" FB 1/4" CB 5/16"CB

$/IN $/IN $/IN

1 $ 6.60

1.25 $ 7.50 $ 7.50 $ 8.90

1.5 $ 8.40 $ 8.40 $ 9.80

1.75 $ 9.30 $ 9.30 $ 10.70

2 $ 10.20 $ 10.20 $ 11.60

2.25 $ 11.10 $ 11.10 $ 12.50

2.5 $ 12.00 $ 12.00 $ 13.40

RABBIT CUT KNIVES

USE 1” WIDE BACK KNIFE THAT IS FOR YOUR DESIRED DEPTH OF CUT.


EDGE CUT KNIFE PARTING KNIFE

1/4" FB 1/4" CB 5/16" CB PRICE

CK-384 EDGE CUT KNIFE 906-9000 916-9000 936-9000 $ 44.28

CK-385 PARTING KNIFE 906-9100 916-9100 936-9100 $ 44.28

HOLDER NUMBER OF KIFE

SLOTS FOR PLANER MODEL PRICE

901-0501 1 CORRUGATED BACK 408, 812 $ 85.00

901-0502 2 CORRUGATED BACK 408, 812 $100.00

901-0503 1 CORRUGATED BACK 612, 615, 720, 816, 820 $ 85.00

901-0504 2 CORRUGATED BACK 612, 615, 720, 816, 820 $100.00

901-0505 3 CORRUGATED BACK 612, 615, 720, 816, 820 $140.00

CORRUGATED MOLDING KNIFE HOLDERS

JIBS AND COUNTER BALANCES

WE RECOMMEND THAT ONLY 1/4”

CORRUGATED BACK KNIVES BE COUN-

TER BALANCED

Length .25 AL .3125 AL Price .25 Steel .3125 Steel Price 1/4 FLAT 1/4 CORR 5/16 CORR Price

0.75 903-0203 903-0253 $6.50 903-0103 903-0153 $11.88 903-0003 903-0033 903-0063 $2.94

1 903-0204 903-0254 $7.00 903-0104 903-0154 $12.50 903-0004 903-0034 903-0064 $3.25

1.25 903-0205 903-0255 $7.50 903-0105 903-0155 $13.13 903-0005 903-0035 903-0065 $3.56

1.5 903-0206 903-0256 $8.00 903-0106 903-0156 $13.75 903-0006 903-0036 903-0066 $3.88

1.75 903-0207 903-0257 $8.50 903-0107 903-0157 $14.38 903-0007 903-0037 903-0067 $4.19

2 903-0208 903-0258 $9.00 903-0108 903-0158 $15.00 903-0008 903-0038 903-0068 $4.50

2.25 903-0209 903-0259 $9.50 903-0109 903-0159 $15.63 903-0009 903-0039 903-0069 $4.81

2.5 903-0210 903-0260 $10.00 903-0110 903-0160 $16.25 903-0010 903-0040 903-0070 $5.13

2.75 903-0211 903-0261 $10.50 903-0111 903-0161 $16.88 903-0011 903-0041 903-0071 $5.44

3 903-0212 903-0262 $11.00 903-0112 903-0162 $17.50 903-0012 903-0042 903-0072 $5.75

3.25 903-0213 903-0263 $11.50 903-0113 903-0163 $18.13 903-0013 903-0043 903-0073 $6.06

3.5 903-0214 903-0264 $12.00 903-0114 903-0164 $18.75 903-0014 903-0044 903-0074 $6.38

3.75 903-0215 903-0265 $12.50 903-0115 903-0165 $19.38 903-0015 903-0045 903-0075 $6.69

4 903-0216 903-0266 $13.00 903-0116 903-0166 $20.00 903-0016 903-0046 903-0076 $7.00


CUSTOM KNIFE QUOTE REQUEST FORM To Request a quote on a custom molding knife fill out this form and fax or mail it to : BUSHTON MANUFACTURING P. O. BOX 127

BUSHTON, KS 67427 FAX: 620-562-3557 E-MAIL: [email protected]

NAME_______________________________________________________________________________________

ADDRESS________________________________________________________________________________

CITY_______________________________________________________STATE____________ZIP______________

PHONE (______)________________ FAX (______)_______________

E-MAIL______________________________________________________________________________________

MOLDING TYPE (ie. Crown, Base etc.)______________________________________________________________

KNIFE TYPE ____1/4” FLAT BACK ____1/4” CORRUGATED BACK ____5/16” CORRUGATED BACK

1. We need a full scale 1 to 1 drawing of the molding or a 4 inch long sample. 2. Due to distortions produced by fax machines, we cannot guarantee a perfect match on prints sent by fax. If you

do use a fax, please include overall dimensions, height and width. 3. A print of the knife will be sent to you for approval. Once you approve the drawing and the knide is made no re-

funds will be given.

T.C.K. (Top Cut Knife) cuts top of board. T.K. (Top Knife) cuts top and side of board.

B.K. (Bottom Cut Knife) cuts the bottom of the board.

Back Cut. Makes the back clearance cut on a board.

S.K.H. (Side Knife) As the molding is pictured it cuts the side of the molding.

2 C.K.H. Req. (2 Custom Knife Holders Required) Requires two custom knife holders.

Cannot be balanced in two single knife holders


ROSETTE CUTTER ITEM # Price per Set

HOLDER 904-0100 $ 65.00

RC-01 904-0101 $ 85.00

RC-02 904-0102 $ 70.00

RC-03 904-0103 $ 57.50

RC-04 904-104 $ 82.50

RC-05 904-0105 $ 80.00

RC-06 904-0106 $ 70.00

RC-07 904-0107 $ 82.50

RC-08 904-0108 $ 80.00

RC-09 904-0109 $ 80.00

RC-10 904-0110 $ 65.00

RC-11 904-0111 $ 70.00

RC-12 904-0112 $ 75.00

RC-13 904-0113 $ 87.00

ROSETTE CUTTERS HOLDERS AND KNIVES

Documents

BUSHTON MANUFACTURING HAWK ustom Knife Department here at ushton Manufacturing. ... 680 ft of shoe @ $ .82 $ 557.60 ... Gives a finished appearance to square or flat edge