-
7/30/2019 Bunny Door Hanging
1/4
YOU WILL NEED:
Fabric (Bunny):36 1 1/4 Yards or 54, 60 or72 7/8 Yard
Contrast 1 (Nose and Cheeks): 8 x 5 Felt RemnantContrast 2
(Inner Ear):45 1/2 YardContrast 3 (Eyes):3 1/2 x 1 1/2 Felt
Remnant
NOTIONS:One Skein each o White and BlackEmbroidery Floss, 3/4 Yd
o 2 1/2 Ribbon, 1/2Yard o Paper Wrapped Wire, Silk Flowers
andFabric Glue.
SUGGESTED FABRICS:Fleece or Felt; Contrasts(Nose, Cheeks and
Eyes): Felt; Contrast (Inner Ear):
Lightweight Cotton.
INSTRUCTIONS:
1. Prepare REMNANT 1 and REMNANT 2, cutalong cutting lines,
separating title, cutting inorma-tion and individual sections. Pin
pattern tissues tocorresponding abric remnant. Cut out
individualpieces. Transer markings.
2.Stitch FRONT and BACK 9 sections togetherat sides and lower
edge between small circles.Remaining sections will be used as
lining.
3. Turn right side out; press. For ront, make running
stitches along stitching line or mouth using blackembroidery
foss. Make long straight stitch betweennose and mouth, as
shown.
4. Center Cheeks 1 within placement lines on ront.Make small
running Stitches along edge o cheeksusing thread the same color as
abric. Center Eyes2 within placement lines on ront; glue in place.
For
Free Project
BunnyDoor
Hanging
2009 Butterick, The McCall Pattern Company 1
Butterick
-
7/30/2019 Bunny Door Hanging
2/4
whiskers, cut our sections rom white embroideryfoss, each
4(10cm) long. Center whiskers overnose, extending ends evenly at
sides.
5. Place Nose 1 over whiskers, centering withinplacement lines;
Glue in place.
6. Stitch ront and back LINING 3 sections togetherat sides and
lower edge between small circles.
7. With wrong sides together, place lining insidebunny, matching
seams. Baste raw edges together.
8. Pin one CONTRAST ear 4 toeach EAR 4, having edges
even.Stitch, leaving upper edge open.
9. Turn right side out; press. Baste raw edgestogether.
10. Pin ears to upper side edges o bunny, havingcontrast side
down and matching squares; baste.Stitch along upper seamline.
11.Turn seam allowance on upper edge o bunnyto inside; press.
Glue in place.
12. On inside, lap 2(5cm) o ends o wire oversides o bunny,
bending wire along seam; glue inplace.
13. Tie ribbon into a large bow. Trim ends, as
shown. Glue bow to upper edge o bunny, asshown. Arrange silk
fowers inside bunny, as desired.
2009 Butterick, The McCall Pattern Company 2
-
7/30/2019 Bunny Door Hanging
3/4
Grainline
REMNANT
CONTRAST 1: Cut 1
CHEEKCHEEK
NOSE
1
Enlarge All Pattern Pieces 200%
EYE
CONTRAST 3: Cut 1
Grainline
2REMNANT
EAR
Fabric: Cut 2
CONTRAST 2: Cut 2
Grainline4
-
7/30/2019 Bunny Door Hanging
4/4
Grainline
PL.LINE
PL.LIN
E
PL.LINE
PL.LINE
PL.LINE S
titchingl
ine
FRONTAND
BACK
Cut4
Stitching line
3
