Bts3902e Quick Guide

BTS3902E WCDMAQuick Installation

Issue: 06Date: 2014-05-30

HUAWEI TECHNOLOGIES CO., LTD.

Guide

This document is applicable to BTS3902E WCDMA Vlater versions (The single-mode base station version m

BTS3902E WCDMA is referred to as BTS3902E in thi

BTS3902E Exterior and Dimensions

BTS3902E

ExteriorBTS3902E has two exteriors.

(1) Upper housing (2) Camouflage shell (3an

Dimensionse s o s

Module Dimensions (H1 x WModule(Without the Housi

BTS3902E working at the 1.9 GHz, 2.1 GHz or AWS frequency band

300 mm120 mm270

BTS3902E working at the 850MHz frequency band 300 mm127 mm270

1

V200R013C00 and later versions / V100R008C00 and mapping to V100R008C00 is: NodeB V200R015C00).is document.

3) BTS3902E with built-in ntenna

(4) BTS3902E with external antennas

W1 x D) Dimensions (H2 x W2 x D) ng) (with the Housing)

0 mm 400 mm145 mm277 mm

0 mm 400 mm170 mm277 mm

1 Copyright Huawei Technologies Co., Ltd. 2014. All rights reserved.

BTS3902E Installation OptionszOn a Metal Pole with zOn a Metal Pole with thezOn a Metal Pole with the Diameter Ranging from 60 mm to 114 mm

zOn a Metal Pole with theDiameter Ranging from 114 mm to 400 mm

BTS3902E Installation Clearance RequzRecommended clearance for installing a single BTS3902

z

zRecommended clearance for installing two BTS3902E side by side

zRecommended clearance for installing two BTS3902E in a vertical line

2

e zOn a Wall zOn a Wood Pole with thee zOn a Wall zOn a Wood Pole with the Diameter Ranging from 200 mm to 400 mm

uirementszMinimum clearance for installing a single BTS3902E

zMinimum clearance for installing two BTS3902E side by side

zMinimum clearance for installing two BTS3902E in a vertical line

2

SPD60D

Two AC surge protection boxes (SPD60D and SPM60A

(Optional) AC Surge Protec

zExterior and Dimensions zRecommendclearance

The outdoor BTS3902E working at the 1.9 GHz or 2.1 GH

Dimensions and Installation Clearance

SPD60D

zOn a Metal Pole with the Diameter Ranging from 60 mm to 114 mm

Installation Options

zOn a Wall

3

A) are available for the BTS3902E.

ction Box

ded installation zMinimum installation clearance

Hz frequency band can use the SPD60D.

Requirements

zOn a Metal Pole with the Diameter Ranging from 114 mm to 400 mm

zOn a Wood Pole with the Diameter Ranging from 200 mm to 400 mm

3

The outdoor BTS3902E working at the 850 MHz frequenc

SPM60A

zExterior and Dimensions zRecommendclearance

The outdoor BTS3902E working at the 850 MHz frequenc

Dimensions and Installation Clearance

zOn a PoleInstallation Options

4

cy band can use the SPM60A

ded installation zMinimum installation clearance

cy band can use the SPM60A.

Requirements

zOn a Wall

4

Installing on a Pole with the1 Installing the angle-adjustable mount

The composing of angle-adjustable mountinLifting eyeAttachment plate Lifting eye

Traction eye

Main mounting bracket

Auxiliary mounting

dhTraction eye

2. Installing the auxiliary mounting bra

Double-headed nutHoist clamp

Ensure that the arrow on the auxiliary bracket points up.

2 Installing the BTS3902E

Tighten the two double-headed nuts synchronously and soand auxiliary brackets are the same.

Upper positioning pin

Lower positioning pin

Put the upper positioning pin through the hole on the ahole on the main mounting bracket.

5

3 Adjusting the installation angle of th

The procedures of adjusting the installation angle

e Diameter of 60 mm to 114 mmting kits

g kits 1. Installing the main mounting bracket

g bracket

double-headed nut

Long bolt

Rubber washerDouble-headed nut

ackets

o that the distances between the two sides of the main

Positioning screw

attachment plate and the lower positioning pin through the

5

he BTS3902E

e, see the page 8.

Installing on a Pole with the1 Installing the mounting brackets

Adapting plate(1) Mounting hole group A

Ad

1. Inst( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

Ada

2. Installing the Hose clamp

Mounting hole group B LeHose clamp


Upper positioning pin


Put the upper positioning pin through the hole on the ahole on the main mounting bracket.

6

3 Adjusting the installation angle of th

The procedures of adjusting the installation angle

e Diameter of 114 mm to 400 mm

ti l t

talling the adapting plate assembly

ain mounting acket

apting plateScrew

Hose clampevel

Positioning screw

attachment plate and the lower positioning pin through the

6

he BTS3902E

e, see the page 8.

Installing a BTS3902E on a 1 Installing the adapting plate assembl


Ada( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

2 Installing the mounting brackets on t1. Drilling holes and install expansion bolt assembliesp

(1) M10x80 b(2) Nut(3) Spring wa(4) Flat wash(5) Expansio


Upper positioni


Put the upper positioning pin through the hole on the attac

7

pp p g p ghole on the main mounting bracket.

4 Adjusting the installation angle of thThe procedures of adjusting the installation angle

7

Wallly

apting plateScrew

ain mounting acket

Screw

the Wall2. Fitting the mounting piece onto the expansion boltsp

bolt

asherhern tube

(1) Insulation washer(2) Flat washer( )(3) Spring washer(4) Nut

ng pin Positioning screw

chment plate and the lower positioning pin through the

7

p p g p g

e BTS3902Ee, see the page 8.

7

Installing on a Wood Pole wto 400 mm

1 Installing the adapting plate assembl


Ada( ) g g p(2) Mounting hole group B(3) Mounting hole group C(4) Adapting plate

Mabra

2 Installing the mounting piece

Mounting hole group C

BoltSpacer

CMountinghole grou

3 Installing the BTS3902EUpper positioning p


Put the upper positioning pin through the hole on the attachole on the main mounting bracket.

8

4 Adjusting the installation angle of thThe procedures of adjusting the installation angle

with the Diameter of 200 mm

ly

apting plateScrew

ain mounting acket

Screw

Nut

Spacer

g up C

pinPositioning screw

chment plate and the lower positioning pin through the

8

e BTS3902Ee, see the page 8.

Adjusting the installation an

Horizontal angle 30, vertical angle 10.If the positioning pin is tightened too hard, the installatiopositioning screw first

1 Adjusting the horizontal angle

positioning screw first.The horizontal angle and vertical angle can be adjusted either from the plan or elevation view.Ensure that the positioning screws both in the vertical d

2 Adjusting the vertical angle

9

ngle of the BTS3902E

on angle cannot be adjusted. In this case, loosen the

simultaneously. The vertical angle can be determined

irection and horizontal direction have been secured.

P iti iPositioning screw

Positioning screw

9

(Optional) Installing the AC

I t ll SPD60D l

Install an SPD60D

When the diain. to 4.49 in.)protection boxWhen the dia(4.49 in. to 15

Install an SPD60D on a pole

(If the diametesmall, cut the

Install an SPD60D on a wall1. Marking the anchor points 2. Installing an e

(1) M10x65 bolt(2) Spring washer 10(3) Plastic tube(4) Flat washer 10(5) Expansion tube

1. Drilling holes 2. Installing t

Install an SPD60D on a wood pole

1

Surge Protection Box

ameter of the pole ranges from 60 mm to 114 mm (2.36 ), the hose clamps delivered with the AC surge x is used.ameter of the pole ranges from 114 mm to 400 mm 5.75 in.), the hose clamps purchased locally is used.) p p yer of the pole around which the clamp is installed is extra part of the clamp.

expansion bolt 3. Installing the SPD60D

0

he AC surge protection box on the wood pole

0

Install an SPM60A on a pole

Install an SPM60A

Install an SPM60A on a pole

1. Marking the anchor points 2. Installing an e

Install an SPM60A on a wall

(1) M10x65 bolt(2) Spring washer 10(3) Plastic tube(4) Flat washer 10(5) Expansion tube

1

expansion bolt 3. Installing the SPD60D

0

1

Installing a PGND Cable

The cross-sectional area of the PGND cable of the BTS

1 Without AC Surge Protection Box

frequency band is 1.5 mm2 .The cross-sectional area of the PGND cable of the BTS

PGND cablePGND cable

External ground bar

2 With AC Surge Protection Box

Equipotential cable

PGND cable

External ground bar

1

S3902 working at the 1.9 GHz, 2.1 GHz, or AWS

Installing an OT terminal in the correct manner

g , ,

S3902 working at the 850MHz frequency band is 6 mm2 .



2

Installing the Power Cable o1 Installing the AC Power Cable of BTS

GHz or 850MHZ Frequency Band)q y )

Without AC Surge Protection Box

Power

With AC Surge Protection Box1.Installing the AC Power Cable of the ACWith AC Surge Protection Box

zInstalling the SPD60D Cable

BTS390

Thread-lock sealing nuof the PG connector

PG connector

Waterproof blockBTS390Blue----Brown-Yellow/zInstalling the SPM60A Cable

Surge protector

Ground

Ca

Waterproof

BTS3902E poBlue----NoutBrown----Lou

1

Waterproof block Yellow/Green

of BTS3902ES3902E(Working at The 1.9 GHz, 2.1

r cable

C Surge Protection Box

02E power cable

External power cableBrown----LinBiue Nin

Insulation layerClip

ut

02E power cable-Nout---Lout/Green ----GND

Biue----NinYellow/Green----GND

terminal

able hole

ower cable

ut

External power cableBrown----LinBiue----Nin

3

n ----GND Yellow/Green----GND

1.Installing the AC Power Cable of the BT

The cross-sectional area of the AC Power cable betwAWS frequency band and an SPD60D is 4.0 mm2 .The cross-sectional area of the AC Power cable betwband and an SPM60A is 2.5 mm2 .There are two types of the AC surge protection box (procedure is the same. The following part uses SPD6

External power cableExternal power cable

BTS3902E power cable

2 Installing the DC Power Cable of BTSBand)

1

TS3902E

ween a BTS3902E working at the 1.9 GHz, 2.1 GHz, or

ween a BTS3902E working at the 850MHz frequency

SPD60D and SPM60A), for which the installing 60D as an example to describe.

S3902E(Working at The AWS Frequency

Power cable

4

Installing the signal Cable1 Installing an FE/GE Fiber Optic Cable

1. Installing the optical module

A fast Ethernet or gigabit Ethernet (FE/GE) cable or fiber

1. R

2.Preparing the FE/GE Optic Cable

1. Rst

2. Tuth

DLC connector

Traction cablescables

3. Installing FE/GE Optic Cable

Clamping jaw

Socket

Clamping jaw

1

e

r optic cable must be installed for BTS3902E as required.

emove the dustproof cap of the optical module andemove the dustproof cap of the optical module and tore it properly for future use.urn the puller of an optical module outwards and insert

he optical module into the OPT0 port on the BTS3902E.

Inner gasket e gas et

1. Sort the optical fibers, remove the dustproof cap from the optical fiber connector, and insert the DLC connector into the optical module.

2. Align the clamping jaw on the inner gasket with thethe inner gasket with the socket of the OPT0 port on the BTS3902E. Insert and fit the clamping jaw into the socket.

3. Push the outer gasket of the round connector upwards and tighten the outer gasket until you hear a click sound

5

until you hear a click sound.

2 Installing an FE/GE Cable

A fast Ethernet or gigabit Ethernet (FE/GE) cable or fiberequired.

3 Installing a Cascading FE/GE Fiber O

When multiple BTS3902Es implement transmission oveinterconnected using a cascading FE/GE fiber optic cablThe OPT1 and ETH ports cannot be both enabled for th

1

er optic cable must be installed for BTS3902E as

Optic Cable

er FE/GE optical ports, the BTS3902Es are le.he same BTS3902E.

6

4 Installing a Cascading FE/GE Cable

When multiple BTS3902Es implement transmission oveinterconnected using a cascading FE/GE cable.The OPT1 and ETH ports cannot be both enabled for th

5 (Optional) Installing the Alarm Cable

1

er FE/GE electrical ports, the BTS3902Es are

he same BTS3902E.

MON port

DB15 male connector

7

(Optional) Installing a BTS3

You must install a radio frequency (RF) jumper when a B

1. Installing the BTS3902E RF jumper

Type N connector

2. Wrap the connector of the BTS3902E

PVCinsulation

Waterproof tapePVCinsulation tape

a. Wrap a layer of PVC insulation tape around the cb. Tightly wrap three layers of waterproof tape aroun

up, the second layer from top down, and the thirdc. Tightly wrap three layers of PVC insulation tape a

bottom up the second layer from top down and tbottom up, the second layer from top down, and td. Bundle cable ties 3 mm to 5 mm away from the e

When wrapping waterproof tape, stretch the tape ev When wrapping insulating tape , do not stretch it. Wrap each layer of tape around the connector tightlyoverlaps more than 50% of the preceding layer.

E th t th id ith dh i t i d

1

Ensure that the side with adhesive tape is covered o When cutting off the cable tie, reserve a surplus leng

3902E RF Jumper

BTS3902E uses an external antenna.

E RF jumper

tape

onnector from bottom up. nd the connector, with the first layer from bottom layer from bottom up.

around the connector with the first layer from the third layer from bottom upthe third layer from bottom up. nd of insulating tape.

enly until it is twice of the original length.

y and neatly, and ensure that each layer of tape

th d t

8

on the wrapped tape.gth of 3 mm to 5 mm.

(Optional) Installing a Camo

There are two types of the BTS3902E. This documen

1. Moving the upper housing

ypinstall the housing.

U

2 Installing the camouflage shell2. Installing the camouflage shell

3. Installing the upper housing

(1) Camouflage shell(2) Slots(3) Tabs

3. Installing the upper housing

HU

1

ouflage Shell

nt uses one type as the example to describe how to yp p

Upper housing

UAWEI TECHNOLOGIES CO., LTD.

9

Huawei Industrial Base Bantian Longgang Shenzhen 518129

Peoples Republic of Chinawww.huawei.com

Documents

Bts3902e Quick Guide