Design Features

Brother Filtration FRP housings are designed for

a variety of industry applications. We offer side

and end connection models and we also offer

custom-designed housing cartered to customer’s

engineering specifications.

Why Brother Filtration Filter?

• Easy installation and maintenance

• FRP housing designed for corrosion resistant

• High chemical resistance

• Designed for compact use and small footprint

• Modular Design

Competitive Investment

Brother Filtration FRP systems utilize performance engineered FRP housings designed for corrosion resistant that potentially reduce your capital start-up costs over typical steel vessels by up to 50%.

Low Maintenance Costs

Advanced pleated filter material design delivers good filtration efficiency and performance. The increased surface of the media provides longer element life, which means fewer change outs. Reduced filter consumption results in minimized disposal, operator exposure and downtime.

Ease of Use

We’ve eliminated the need for heavy equipment,

such as cranes to open vessel doors or remove

cumbersome baskets. Access to the filtration elements

requires virtually no tools.

• Easy-to-remove, tool-less retaining ring • Convenient handle on the cover plate

• Ergonomic handle on the element for easy

entry and exit

• Guided tabs for quick element access

and precision alignment

Compact Design Than Other Competitors

Offers reduced system footprint, up to 50% smaller

than competitively sized housings.

Applications

• Pretreatment

• RO Prefiltration

• Seawater desalination

• Condensate water filtration

• Hot water recovery in power generation

• API, Solvents, and water filtration in

Biopharma market

• Bottled water filtration

• High fructose, edible oil, soft drinks and milk

• Paints and coatings

• Petrochemical and Refineries

• Microelectronics, Film, Fiber and resin

www.esli.com.tr

Brother Filtration

Max-A High Flow FRP Cartridge System

Max-Flow Purification Systems

MAX-A SERIES DIFFERANTIAL PRESSURE vs FLOWRATE

MAX-A SERIES DIFFERANTIAL PRESSURE vs FLOWRATE

Designed to provide optimum filtration while significantly reducing

operating costs and offering overall energy and cost savings.

• Increased energy savings

• 20inch one-piece design hard cage for better integrity

• Infrared ray ultra-high temp thermal welding for stronger connection and pressure resistance

• Significantly lower installation costs

• Lower operating costs

• High loading capacity

• Two handle design ease of installation and maintenance

• Longer life span

High Flow Cartridge Filter

High Flow Cartridge

Pleated Cartridge

Depth Cartridge

Advantage of Max-A High Flow FRP Cartridge System

MAX-A

HF CARTRIDGE

MODEL

EFFECTIVE

MEMBRANE

AREA (m2)

FLOW RATE CARTRIDGE

FILTRATION

EFFICIENCY Max flow

rate (m3/hour)

Recommend flow rate (m3/hour)

LENGTH

(mm)

STRUCTURE

BF-HFA-60 8 113 50 1524 7- layer 99,10 %

BF-HFA-40 5.3 75 33 1016 7- layer 99,10 %

BF-HFA-20 2.66 38 17 508 7- layer 99,10 %

Side-Connected Model Brother Filtration Max-Flow FRP system is designed for filtration system technologies. We respond to market

needs and requirements by paying attention to critical applications, cartridge filter care and protection.

It offers high quality, while offering lower capital investment and operating costs in a small footprint. Our

innovative proprietary design allows for easy and fast maintenance for minimum downtime that ensure your

systems run continuously.

SYSTEM SPECIFICATION

Element Type Max-A High Flow Cartridge System

Micron Ratings 01, 05, 10 & 20 Micron Nominal/Absolute

Diameter of Cartridge 6inch/152 mm

Length 60inch, 40inch, 20inch

Suggested Pressure Drop

for Element Replacement

1.5 bar

Max. Temperature ~70℃

Flow Direction of Filter System End in, side out

Flow Direction of Filter Cartridge Inside-Out

FRP

HOUSING

MODEL CONNECTION MAX. PRESSURE

FILTER HOUSING

LENGTH DIAMETER

MF 80-150S-60 3” coupling 150 Psi / 10 Bar 1860 mm 800 mm

MF 80-150S-40 3” coupling 150 Psi / 10 Bar 1350 mm 800 mm

MF 80-150S-20 3” coupling 150 Psi / 10 Bar 792 mm 800 mm

Max-A High Flow FRP Cartridge System

MATERIALS

HOUSING

Shell FRP

End caps ABS

End cap handle Stainless steel 304

Inlet ABS

Side port outlet Nylon

Locking segment Stainless steel 304

Saddle Rubber

CARTRIDGE

Media (membrane) Polypropylene/Glass Fiber

Supporting layer Polypropylene

Seal EPDM/Silicone/Viton/Buna-N

Inner frame/Core Polypropylene

Lifting Handles Polypropylene

Outer Cage Polypropylene

ACCESSORIES

ITEM NO. NAME QUANTITY

① O-ring 4

② Locking Kit Segments 6

③ End Cap (Handle Side) 1

④ End Cap (Insert Side) 1

⑤ Thrust Ring 1

⑥ Guiding Frame 1

⑦ Saddle 2

⑧ Strap 2

⑨ Couplings 2

⑩ Short Tube 2

Remarks: ①-⑧ Free Accessories, ⑨-⑩ Additional Options

CARTRIDGE FILTER AND HOUSING CONSTRUCTION MATERIALS & ACCESSORIES

Professional Design of Max-A High Flow FRP Cartridge System

Brother Filtration has a professional and experienced technical team to help our customer choose fittest products, recommend design solution, offer graph drawing as well as OEM services Besides, Brother Filtration keep improving and offering innovative NEW products to meet different clients’ requirements

Make The Right Choice

Brother Filtration

Understanding

your water

application and

the importance

of using health,

chemical free

water is the first

step towards

healthier living.

Finding the right

water filtration

systems for your

application is the

next step.

Food & Agriculture

Chemical & Petrochemical

Biotech & Pharmaceutical

Industrial

www.brotherfiltration.com info@brotherfiltration.com

How to Install Max-A High Flow FRP Cartridge System?

Before cartridge installation, put the Guiding

Frame onto cartridge Step 1: Insert HF Cartridge from Inlet

Step 2: Insert Inlet End Cap with O-ring and

Install Locking Kit Segments

Step 3 & 4: Insert Thrust Ring from the Other

Side FRP Housing

Step 5: Insert Closed End Cap with O-ring

Step 6: Install Locking Kit Segments

For later cartridge change-outs

Open from the Closed side End Cap