EAH 422

ADVANCED WATER RESOURCES ENGINEERING

Bridge HydraulicsProf. Aminuddin Ab. Ghani

W e l e a dReferences

W e l e a dThe Art And Science Of River Engineering

W e l e a d

Pier scour Pier scour

Pier scour

Bridge Failure

W e l e a d

Abutment scour Abutment scour

Bridge Failure

W e l e a d

Bridge Failure

Sungai Nenggiri, Gua Musang

Destroyed by floating debris during Dec 2014 flood

W e l e a d

Bridge Failure

Sungai Tanum, Kuala Lipis

Abutment scour during Dec 2014 flood

W e l e a d

Cross Drainage 

Structure built over the roads, railways and rivers

• Culverts ‐ shorter span < 6 m

• Bridges ‐ high‐level crossing structures which can beexpensive for large rivers. It is therefore essential to protectthem even from rare floods.

W e l e a dSungai Muda

W e l e a dSungai Muda

Pier Group

W e l e a d

Sungai Muda

Pier Group

W e l e a d

Sungai Muda

Abutment

W e l e a d

SHOUJIANG BRIDGE (Sichuan, China)

The tallest piers were approximately 196.8 ft(60 m) high, the approach spans were 98.4 ft (30 m) long, and the four main spans were 131.2 ft (40 m) long

W e l e a d

Three span structure with a total length of 150m including a 70 m main span

River Erne Bridge (Ireland, UK)

W e l e a d

In‐stream Sand Mining and Riverbed Degradation

Sungai Muda @ Jeniang

W e l e a dHydraulic Issues in Bridge Design

The presence of a bridge across a stream createsconstricted flow through its openings because of

(a) the reduction in the width of the stream due topiers and their associated end contractions and

(b) the fluming of the stream itself (in the case ofwide streams with flood plains) to reduce the costsof the structure

W e l e a d

Velocity and streamlines at a bridge constriction

In the bridge opening, approximately 90 percent of the flow is in the channel and 10 percent is in the floodplain area between the channel banks and abutments (setback area). Flow velocity is less than 1.7 m/s in the upstream channel and 0.37 m/s in the upstream floodplains.This compares with velocities in bridge opening as high as 2.7 m/s in the channel and 1.34 m/s in the setback areas. The higher velocities in the bridge opening generate much higher shear stresses and are much more erosive than the upstream flow velocities. In addition to the increased velocities, bridge structural elements (piers and abutments) locally obstruct flow and cause additional erosion at these locations.

W e l e a dHydraulic Issues in Bridge Design

• Local scour around the piers and bridge abutmentsand possible bed erosion

• A considerable backwater effect of the bridge. Thecorresponding afflux (rise in upstream water level)depends on the type of flow (subcritical orsupercritical).

• As most bridges are designed for subcritical flowconditions in order to minimize scour and chokingproblems, further discussions here are mainlyconfined to subcritical flow.

W e l e a dHydraulic Issues in Bridge Design

The establishment of afflux levels is extremelyimportant for the design of upstream dykes and otherprotective works and also for the location of safe bridgedeck levels (to avoid the flooding of the deck and anyconsequent structural damage).

It is equally important to determine the minimum clearlength of span (economic considerations) which willnot cause undesirable afflux levels.

W e l e a dBACKWATER EFFECT (AFFLUX)

W e l e a dBACKWATER EFFECT (AFFLUX)

W e l e a d

Afflux

W e l e a d

Afflux

W e l e a d

Afflux

W e l e a d

Recommended ARI for Road Crossing Design (REAM, 2004)

W e l e a d

Recommended Freeboard for Road Crossing Design (REAM, 2004)

W e l e a dGuidelines

All bridges and crossings shall bedesigned to allow for the design flow.

The minimum freeboard (clearance) atthe design flow level shall be 0.3 m.Where floating logs are expected, thisminimum clearance shall be 1 m.

There shall be no piers or (vertical wall of culverts) in the middle of the river cross‐section. 

For multiple box culverts, twin box culverts should be avoided and instead to use triple box culvert with the centre box in line with the mid‐flow section of the river or channel. 

Department of Irrigation and Drainage, Malaysia (2009)

W e l e a d

Guidelines

Banks stability analysis should be made. All bridges shall be studied for scour effects. 

Bridge soffit should be at least 1 meter higher than flood level (100‐year ARI). Abutment walls shall be constructed at least 2 metres from the edge. Pile caps shall be constructed with a minimum depth of 1.5 meters below the 

ground level.

Department of Irrigation and Drainage(www.water.gov.my)

W e l e a d

Guidelines

Design Requirement for Bridge

Department of Irrigation and Drainage(www.water.gov.my)

W e l e a d

Guidelines

Pre‐cast Span Structure showing set back abutments and deep foundations

Scottish Environment Protection Agency (SEPA), Scotland (2010)

An Example of Span Bridge 

W e l e a d

Guidelines

A well designed clear‐span bridge retaining the existing riverchannel with piers set back from the river bank

National Roads Authority, Dublin, Ireland (2008)

W e l e a d1. Backwater Level 

• Short constrictions ‐narrow bridge without approach fluming‐few piers‐bw relatively less important‐refer to Figure 10.10

(10.8)

KB = bridge loss coefficient (Table 10.2) = conveyance ratio = Kb/KB = b/BV2 = d/s velocityL = bridge length, see Fig. 10.10S0 = normal bedslope = contraction ratio = 1‐

gVLS

gVKh B 22

21

10

22

W e l e a d

Table 10.2: Bridge loss coefficient, KB KB1.00.80.60.40.2

1.001.361.671.881.92

Figure 10.10: Flowprofile through bridgewith contracted channelof relatively short length

W e l e a d1. BACKWATER LEVEL (bw)

• Long constrictions ‐Large number of bridge piers; long approach embankment;‐Considerable backwater effects‐y = results of presence of piers & channel contractions‐Yarnell’s (1934) equation, refer to Figure 10.10

(10.12)

K = a function of pier shape (Table 10.3)Fr = Froude number = ‐valid if  is large, i.e. subcritical flow with no choke‐for critical flow with choke effects (Fig. 10.11), limiting  value

423

23

3

5.16.05 FrKKFry

y

33 / gyV

323

43

3

21

12

Fr

Fr

W e l e a d

W e l e a d

Table 10.3:   Values of K as a function of pier shape

Pier Shape K Remarks

Semicircular nose and tail Lens-shaped nose and tailTwin-cylinder piers with connecting diaphragm

Twin cylinder piers without diaphragm 900 triangular nose and tail

Square nose and tail

0.900.900.95

1.051.05

1.25

All values applicable for piers with length to breadth ratio equal to 4; conservative estimates of y have been found for larger ratios

Lens-shaped nose is formed from 2 circular curves, each of radius to twice the pier width and each tangential to a pier face

Figure 10.11: Flowprofile with chokeflow conditions

W e l e a d

2. DISCHARGE COMPUTATIONS AT BRIDGE PIERS 

• For subcritical and near critical flows (Nagler ,1918), Fig. 10.12

(10.16)

KN = Coefficient depending on channel contraction (Table 10.4) = Correction factor intended to reduce the depth y3 to y2

Default value = 0.3 = Correction for the velocity of approach (Fig. 10.12b)

gVh

gVygbKQ N 22

22

13

23

32/1

W e l e a d

Table 10.4: Values of KN and KAType of pier Conveyance Ratio,

0.9 0.8 0.7 0.6 0.5

KN KA KN KA KN KA KN KA KN KA

Square nose and tailsSemicircular nose and tails900 triangular nose and tailsTwin-circular piers with/without diaphragmsLens-shaped nose and tails

0.910.940.950.910.95

0.960.99

1.00

0.870.920.940.890.94

1.021.13

1.14

0.860.950.920.880.97

1.021.20

1.22

0.871.03

1.001.26

0.891.11

0.971.31

Figure 10.12:Dischargecomputationsthroughobstruction

W e l e a d

2. DISCHARGE COMPUTATIONS AT BRIDGE PIERS 

• d’Aubuisson ‘s (1840) Formula, Fig. 10.12a

(10.17)

KA = A function of channel contraction, shape and orientation of obstruction (Table 10.4)

‐An approximate formula

• Chow (1983)‐Chart produced‐With values of  and y3, obtain the value of x‐enter x, values of F3 and K in the chartto obtain the backwater h

2/121332 2 VghybKq A

W e l e a d3. SCOUR DEPTH UNDER THE BRIDGE

Type of scour

Local scourContraction scourGeneral scour

W e l e a d

General Scour‐ aggradations or degradations of the riverbed not related to the pressure of local obstacles 

Contraction Scour‐ involves removal of material from bed and bank across most of the channel width

Local Scour‐ scour around obstacles in the path of the water flow 

W e l e a d

General Scour: Sediment Transport 

Contains all the latest research developments in hydrodynamics of sediment transport

W e l e a dSediment Transport Equation for Malaysia

Sinnakaudan, S. K., Ab. Ghani, A., Ahmad, M. S. S., & Zakaria, N.A.(2006). Multiple Linear Regression Model for Total Bed Material Load Prediction, Journal of Hydraulic Engineering, American Society of Civil Engineers, Vol. 132, No. 5, May, pp. 521-528. ISSN 0733-9429

W e l e a d

Local Scour

W e l e a d

Total Scour at Pier

General Scour +

=

Contraction Scour Local Scour+

Figure: The types of scour that can occur at a bridge

W e l e a d

Physical model of the I‐90 Bridge over Schoharie Creek, New York

W e l e a d

Local Scour at Piers

W e l e a dLocal Scour at Pier

‐ Acceleration of flow around the pier

‐ Formation of the vortices

‐ The horseshoe vortices removals material from the base

‐scour hole

W e l e a d

Types of Local Scour

W e l e a dCOMMON PIER SHAPES

W e l e a d

3. MAXIMUM SCOUR DEPTH AROUND BRIDGE PIERS

W e l e a d

3. MAXIMUM SCOUR DEPTH AROUND BRIDGE PIERS

W e l e a d

3. MAXIMUM SCOUR DEPTH AROUND BRIDGE PIERS

9.  Khan, Azamathulla & Ab. Ghani (2012)

W e l e a d

Many different types of countermeasures for local scour at bridge piers areintroduced in the literature. Using riprap is one of the commoncountermeasures to control the pier and abutment scours.

Ripraps

Ripraps around Pier Ripraps around Abutment

3. SCOUR PROTECTION WORKS AROUND PIERS AND ABUTMENTS

W e l e a d

3. SCOUR PROTECTION WORKS AROUND BRIDGE PIERS

• Pier shape‐shape nose, cylinder

• Normal practice‐provide thick protective layers of stone or concrete apron around the piers‐Riprap protection (Bonasoundas, 1973)

Riprap

D = 0.06 – 0.033U + 0.04U2  D = thickness of riprap (m)Uc= 6d1/3y01/6  U= mean velocity (m/s)

or for horizontal bed  Uc= mean critical velocityUc = 4.29d1/2 d = armour stone size (m)

‐The riprap should be placed on a suitable inverted filter or a geotextile fabric (Figure 9.8)

W e l e a d

3. SCOUR PROTECTION WORKS AROUND BRIDGE PIERS

W e l e a d

The collars change the formation of the mechanisms and result in shifting the vortex away from the immediate vicinity of the pier or abutment.

3. SCOUR PROTECTION WORKS AROUND BRIDGE PIERS

Collars

W e l e a dLocal Scour at Abutment

Flow pattern around an abutment

W e l e a dLocal Scour at Abutment

Uniform Abutment (Without Foundation)

W e l e a dLocal Scour at Abutment

Compound vertical‐wall abutment

W e l e a dLocal Scour at Abutment

W e l e a d

Compound Abutment (With Foundation)

Local Scour at Abutment

W e l e a dLocal Scour at Abutment

Uniform Abutment (Without Foundation)

W e l e a dLocal Scour at Abutment

Compound Abutment (With Foundation)

W e l e a dLocal Scour at Abutment

Estimating scour depth at a complex abutment:The effective length and Regression methods, can be used to predict the depth of scour at compound abutment:

Thank you

Presented byName | Centre/Schools/Units etc