Brazed Carbide Tool Bits...501-33B 15 DEGREE CHAMFER TOOL BIT NOTE: CHAMFERING CUMMINS BLOCK 501-33D 30 DEGREE CHAMFER TOOL BIT 8029 S 200t Street, Ket, WA 98032 USA P …

8029 S 200th Street, Kent, WA 98032 USA | Ph: (253) 872-7050 | Fax: (253) 395-0230www.rottlermfg.com

100-29.438” OFFSET TOOL BIT FOR BORING BLIND HOLES

100-29-6.525” OFFSET RF TOOL BITNOTE: FOR MERCURY OUTBOARD BLIND HOLE SLEEVES

100-29-7.438” OFFSET GM TOOL BIT, 60 DEGREE V-6

100-74VW THRUST FACING TOOL BIT

100-76OFFSET TOOL BIT 1/2” (12.7mm) WIDE, VW CYLINDER HEAD FACING

Brazed Carbide Tool Bits


501-28STEEL CUTTING TOOL BIT, W/CHIP CURLERNOTE: STEEL CUTTING W/CHIP CURLER TO BREAK UP CHIPS WHILE BORING

501-29ARF FACING & COUNTERBORING TOOL BITNOTE: FOR FACING & COUNTERBORING OF CAST IRON CYLINDER BLOCKS AND FOR CUTTING OFF SLEEVE

501-29BRFS RIGHT FACING TOOL BIT FOR STEELNOTE: FOR FACING & COUNTERBORING OF STEEL CYLINDER BLOCKS AND FOR CUTTING OFF SLEEVES

501-30-1R1 CARBIDE TOOL BIT, 1” (25.4mm)NOTE: FOR HI SPEED FINISHING, NON- INTERRUPTED CUTS

501-30-2R1 CARBIDE TOOL BIT, 1 3/8” (34.93mm)NOTE: FOR HI SPEED FININSHING, NON- INTERRUPTED CUTS


501-31-1R8 CARBIDE TOOL BIT, 1” (25.4mm)NOTE: FOR GENERAL PURPOSE & HEAVY CUTS ON CAST IRON, RECOMMEND FOR INTERRUPTED CUTS

501-31-2R8 CARBIDE TOOL BIT, 1 3/8” (34.93mm)NOTE: FOR GENERAL PURPOSE & HEAVY CUTS ON CAST IRON, RECOMMEND FOR INTERRUPTED CUTS

501-31ACUMMINS COUNTER- BORING TOOL BITNOTE: FOR COUNTERBORING OF CUMMINS DIESEL CYLINDER BLOCKS

501-32-1GROOVING TOOL BIT, SPECIAL, .048







501-32-8TOOL BIT, SPECIAL GROOVING, .062




501-32-11.051” WIDE GROOVING BIT (LONG OFFSET) SPECIAL

501-33B15 DEGREE CHAMFER TOOL BITNOTE: CHAMFERING CUMMINS BLOCK

501-33D30 DEGREE CHAMFER TOOL BIT


501-33E45 DEGREE CHAMFER TOOL BIT

501-33-1R8 CARBIDE 12 DEGREE HI RAKE TOOL BITNOTE: FOR ROUGHING CUTS

501-33-2R1 CARBIDE 12 DEGREE HI RAKE TOOL BITNOTE: FOR ALUMINUM VEGA

501-59HARD CYLINDER SLEEVE BORING TOOL BIT, (SPECIAL ONLY)NOTE: DO NOT USE FOR CAST IRON

6260CR8 BRAZED CARBIDE TOOL BIT, 1 3/16” (30.16mm)NOTE: THIS IS A BRAZED CARBIDE TOOL BIT. SURFACE SPEEDS BETWEEN 200 AND 400 FEET PER MINUTE SHOULD BE USED WITH THIS TOOL FOR HIGHER SPEEDS SEE 6301F, 6301Q, 6301J, 6301S, 6301E


6260DR8 BRAZED CARBIDE TOOL BIT, 1 7/8” (47.63mm)

6260ER8 BRAZED CARBIDE TOOL BIT, 13/16” (20.64mm)

6260PRF BRAZED CARBIDE TOOL BIT, 1 3/16” (30.16mm)

6260RRF BRAZED CARBIDE TOOL BIT, 1 7/8” (47.63mm)

6260UR1 BRAZED CARBIDE TOOL BIT 1 3/16” (30.16mm)

6260VR1 BRAZED CARBIDE TOOL BIT, 1 7/8” (47.63mm)


650-2-32KOIL GROOVE CAM LINE BORING TOOL BIT

6513DOFFSET FACING TOOL BIT, BRAZED 3/8” WIDE X 1/2” DIA. X 1 7/8” LONG (9.53mm) WIDE X (12.7mm) DIA X (47.63mm) LONG

6513EFACING TOOL BIT, BRAZED 1/2” WIDE X 1/2” DIA. X 1 7/8” LONG (12.7mm) WIDE X (12.7mm) DIA X (47.63mm)

6513FOFFSET BORING TOOL BIT, BRAZED, 1 7/8’ (47.63mm)

6513JGROOVING TOOL BIT, .037 WIDE


6513LGROOVING TOOL BIT, .039 WIDE

6513NGROOVING TOOL BIT, .060 WIDE

6513PGROOVING TOOL BIT, .085 WIDE

6513QGROOVING TOOL BIT, .120 WIDE

6513RRADIAL GROOVING TOOL BIT, .080”WIDE (SPECIAL ORDER ONLY)


6513T.051” WIDE GROOVING TOOL BIT

6513U.049” WIDE GROOVING TOOL BIT

6513V.120” WIDE RADIUS GROOVING TOOL BIT

6513W.041” WIDE GROOVING TOOL BIT

653215 DEGREE CHAMFER TOOL BIT, BRAZED


6532A30 DEGREE CHAMFER TOOL BIT, BRAZED

6532B10 DEGREE CHAMFER TOOL BIT, BRAZED

6532G45 DEGREE CHAMFER TOOL BIT, BRAZED

6755ELINE BORING TOOL BIT 1 9/32” (32.54mm)

6755FLINE BORING TOOL BIT 1 3/8” (34.93mm)


6755JLINE BORING CHAMFERING TOOL BIT 1 1/16” (26.99mm)

6755KLINE BORING CHAMFERING TOOL BIT 1 3/8” (34.93mm)

Documents

Brazed Carbide Tool Bits...501-33B 15 DEGREE CHAMFER TOOL BIT NOTE: CHAMFERING CUMMINS BLOCK 501-33D 30 DEGREE CHAMFER TOOL BIT 8029 S 200t Street, Ket, WA 98032 USA P …