BQ Design Bedding Catalogue

2

B E D D I N G

B E D D I N G

BQ DESIGN IS AUSTRALIA’S LEADING MANUFACTURE OF CUSTOM MADE BLINDS, CURTAINS, BEDDING, UPHOLSTERY

AND CUSHIONS.

OUR EXCLUSIVE STATE-OF-THE-ART MACHINERY AND HIGHLY SKILLED CRAFTS PEOPLE CREATE THE HIGHEST QUALITY

PRODUCT TAILORED TO YOUR EXACT SPECIFICATIONS.

BQ DESIGN IS COMMITTED TO EXCELLENCE IN SERVICE AND MANUFACTURING AND PROVIDES A 3 YEAR WARRANTY

FOR REPAIR OR REPLACEMENT SHOULD COMPONENT FAILURE OR A MANUFACTURING FAULT OCCUR.

OUR ON-LINE JOB TRACK SYSTEM ALLOWS YOU TO MONITOR THE PROGRESS OF

YOUR JOB ANY WHERE, ANYTIME. WE ALSO PROVIDE A DELIVERY DATE AT THE

COMMENCEMENT OF EVERY JOB – THAT’S OUR PROMISE.

CONTENTS

BEDHEADS AND WALL PANELS 1

BEDSPREADS – QUILTED THROWOVERS 3

BEDSPREADS – QUILTED CAP TOPS 5

BEDSPREADS – QUILTED, FULLY TAILORED 7

QUILT COVERS 8

THROW RUGS 9

BED VALANCES 10

PILLOW CASES AND CUSHIONS 11

SIZING 12

ESSENTIAL INFORMATION 13

B E D D I N G

1

BEDHEADS

BQ Design offer a range of fully upholstered

bedhead styles and shapes which you can select

from to suit your design needs.

Choose your style then select your required shape.

WALL PANELS

Upholstered Wall Panels are a versatile and

creative touch in home decorating, and can be

used effectively as an alternative to bedheads.

2

Optional Additions

Order Code BH7

Deep diamond buttoned

Order Code BH4

Plain

Single row of piping to edge

Order Code BH3

Padded Roll

Piping inserted below roll

Order Code BH5

Walled

Piped front and back edge

Order Code BH1

Stuckey

Attached to the wall above the bed,

does not go to the floor

Available in Shape 8 only, square

Style Choices

Studs Covered buttons –

20mm diameter

AlternativesBH1 Alternative – Half Projection (55mm)

BH4/BH5 Alternative – No piping

BH5 Alternative – Wrapped effect with no piping or seam along walled edge,

only applicable to Shape 8.

Shape Choices

Shape 1

Square, rounded cornersShape 2

Square, cut-off corners

Shape 3

Square, inverted corners

Shape 7

Georgian

Shape 5

Clover

Shape 8

Square

Bedhead with base cut-out Standard bedhead without base

cut-out

Skirting board cut-outs

Only applicable to Order Code BH5

Shape 4

Oval

Shape 6

Queen Anne

B E D D I N G

3

All quilting designs are interchangeable with bedspread styles.

Quilted bedspreads may be designed to sit to the floor and are available in tailored or rounded corners.

Border Diamond

Frame Quilting

Available only in standard cap

top sizes

Outline Channel

Recommended for all linear

prints

Outline of fabric patternShell

Frame Quilting

– 20cm

Elongated Diamond

Frame Quilting

– 23cm

Tuft Square

Frame Quilting

– 15cm

Straight Diamond

Frame Quilting

– 15cm

Tuft Diamond

Frame Quilting

– 30cm

Square

Frame Quilting

Available in 15cm, 20cm,

25cm and 30cm

Multi-needle Channel

Available in 7.5cm, 10cm,

12.5cm, 15cm, 17.5cm, 20cm

and 22.5cm

Quilting Styles

Unless specified, Reverse Sham (80-85cm) is standard on all BQ Design Bedspreads (refer to images opposite).

Grey

4

Order Code BS10

5cm Blind stitched edges

Pictured: Frame Quilting

– 15cm Straight Diamond

Order Code BS1

8cm Rolled edges



Alternative: 7cm self or contrast piping

can be inserted above rolled edges

Order Code BS1A

Order Code BS10 Alternative

Sewn down corners

Pictured: Multi-needle Quilting

– 10cm Channels

Order Code BS7

7mm Self or contrast piped edges


– 20cm Shell

Order Code BS12

6cm Self or contrast band on edges


– 25cm Square

Order Code BS8



– 15cm Square

Alternative: Continuous Sham Alternative: No Sham

B E D D I N G

5

BEDSPREADS

Quilted Cap Tops


Cap Top Bedspreads are designed to fall just below the mattress allowing your valance or bed base to

remain visible.

Unless specified, the following is standard on all BQ Design Cap Top Bedspreads:

Reverse Sham (80-85cm) Rounded corners (All Order Codes except BS17A and BS31)

Alternatives: No Sham and Continuous Sham Square Corners

6

Order Code BS17A

8cm Double sided flanged edges



Order Code BS18

5cm Plain sewn edges


– 20cm Shell

Order Code BS19



– 15cm Square

Order Code BS19T

Tailored Corners (Can also be applied to Order

Code BS18)

Pictured: Multi-needle Quilting

– 15cm Channels

Order Code BS22

16mm Bound edges


– 15cm Square

Order Code BS21

7mm Self or contrast piped edges


– 20cm Shell

B E D D I N G

7

Alternatives No Sham and Continuous Sham

BEDSPREADS

Quilted, Fully Tailored


Quilted, Fully Tailored bedspreads feature a piped bedline.

The bedline can be self or contrast piped, or substituted with a decorative cord.

Unless specified, Reverse Sham (80-85cm) is standard on all BQ Design Bedspreads.

Order Code BS31

Cap Top

Piped bedline, split corners,


Pictured: Frame Quilting – 15cm Square

Order Code BS24

Full bedspread

Piped bedline, split corners,


Pictured: Multi-needle Quilting – 15cm Channels

8

QUILT COVERS

Quilt covers are available in plain or quilted styles and are finished with a zipped opening.

Unless specified, plain edges are standard on all BQ Design quilt covers.

B E D D I N G

9

Order Code BT1

Unquilted, Reversible,

Plain edges

Order Code BT2

Quilted, Reversible,

16mm Bound edges


– 20cm Square

Order Code BT3

Quilted top, Bag lined underside,

4.5mm Piped edges

Pictured: Outline Quilting

Order Code BT6


7cm Flange on ends

Pictured: Multi-needle Channel Quilting

– 22.5cm

Order Code BT8

Quilted top, Bag lined underside, 10cm

Contrast band on four edges – top only

Pictured: Outline Quilting

Order Code BT7


15cm Contrast band on ends – top only

Pictured: Frame quilting

– 30cm Tuft Diamond

Throw RugsThrow rugs are 65cm wide and are designed to lay across the end of the bed.These can also be made wider to your specifications.

Unless specified, 70 gram polyester filling is standard on all BQ Design Throw Rugs.

Multi-needle Quilting – 22.5cm Channels

10

BED VALANCES

Bed valances are designed as a decorative treatment to conceal your bed base. These are available lined or

unlined and are standard with a 10cm mattress band.

Order Code BV1

Gathered

Order Code BV2

Tailored. Inverted pleat at foot corners,

centre of sides and centre of foot.

Order Code BV2A

Inverted pleats

approx. 30-40cm apart

Order Code BV4

Vertical channel pleated

B E D D I N G

11

PILLOW CASES AND CUSHIONS

Additions including Piped edges, Flanged edges, Bands and Quilting can be applied to pillow cases

and cushions.

12

SIZING

Refer to the following tables for standard sizes.

Custom sizes can be requested.

BEDSPREADS Full Bedspread Cap Top

Style Rolled Edge Style OtherSizes

Bed Width cm Length cm Drop cm Drop cm Drop cm

SB 92 188 56 54 35

KSB 107 203 56 54 35

DB 138 191 56 54 35

QS 153 204 56 54 35

KS 183 204 56 54 35

BEDHEADS

MAXIMUM HEIGHT 150CM

BH1 - Stuckey5.5cm and 10cm Projections available

BH3, 6.5cm projectionBH4, 6cm projectionBH5, 8cm projection

Size Width cm Height cm Width cm Height cm

SB 97 60 110 120

KSB 112 60 127 120

DB 143 60 158 120

QS 158 60 173 120

KS 188 60 203 120

BED VALANCESBed Width cm Length cm Drop cm

SB 92 188 33

KSB 107 203 33

DB 138 191 33

QS 153 204 33

KS 183 204 33

PILLOW CASESSizes Width cm Length cm

Standard 72 48

KS 75 55

European 65 65

THROW RUGSBed Width cm Length cm

SB 152 65

DB 198 65

QS 213 65

KS 243 65

QUILT COVERSBed Width cm Length cm

SB 140 210

DB 180 210

QS 210 210

KS 240 210

Standard Sizes

B E D D I N G

13

ESSENTIAL INFORMATION

Bedheads

Back of BedheadFully upholstered in BQ ivory cotton providing a neat appearance and concealing fabric turnings and piping tails.

Base Cut-outStandard with no cut-out. Optional cut-out applicable to Order Code BH3, 4 and 5 to allow for power points.

Buttons2cm diameter.

Positioning, unless otherwise requested:

First row 20cm down from the top edge

Second row 20cm down from first row

SB 2 buttons across per row, 30cm apart

KSB 4 buttons across per row, 30cm apart

DB 4 buttons across per row, 30cm apart

QS 4 buttons across per row, 30cm apart

KS 5 buttons across per row, 30cm apart

Non standard height – the same will apply, unless otherwise requested.

ConstructionTimber used is Medium Density Fibreboard (MDF). High density foam is covered with 200 gram polyester, providing a soft, padded effect.

InterliningRecommended for silks and lightweight fabrics. This process avoids discolouration of fabrics. The ivory cotton lining behind gives a truer colour and reduces darkening at the seams when fabric cannot be railroaded.

Mounting BracketOrder Codes BH3, 4 and 5 are designed to be set on the floor or mounted above the skirting. A mounting bracket is supplied for the bedhead to be attached to the wall.

Order Code BH1 is designed to be mounted on the wall so that the base of the bedhead is level with the top of the mattress. The mounting bracket is inset into the back of the framework so the bedhead sits flush with the wall.

Railroading FabricWhen fabric is non-directional, we recommend turning the fabric to avoid seams. Even where grain direction is visible, we believe the product is more pleasant to the eye when seams are avoided.

Roll Sizes90mm or 125mm. 90mm is used on single bed size and 125mm on all other sizes unless otherwise requested.

ScotchgardTM Protector (“Scotchgard” is a trademark of the 3M Company) Repels spills and stains to keep furnishing items clean and looking new for longer.

ShapesAre a guideline – we can manufacture different shapes to templates provided.

StudsSuggested for added interest on rolled edge style Order Code BH3 and applied at the join of the roll to the centre insert (in lieu of piping). Studs are also applied to the edges of BH4 and BH5 syles. BQ Design stock some finishes, otherwise studs can be coupled with fabric.

Bedhead with base cut-out

Bedhead Wall

Mounting bracket for attachment to wall(side view) – not to scale

14

LiningPre-shrunk ivory cotton.

Quilting DesignsFrame Quilting – Fabric is joined prior to quilting, thus providing perfect pattern match and quilt match, however, joins will be exposed. Due to restrictions on the size of the frame, some king size styles cannot be accommodated – we suggest multi-needle channel quilting. Frame Quilting designs in this catalogue are those which we currently have set up on our machine. We would welcome other designs with consideration to adding these to our standard range.

Multi-needle Channel Quilting – Fabric is quilted prior to joining. Joins will occur in a channel stitch concealing the join, however we are unable to obtain perfect pattern match on printed designs. We request that you simply specify narrow channels (7.5, 10 or 12.5cm) or wide channels (15, 17.5, 20 or 22.5cm) and BQ Design will choose the most appropriate width to suit the horizontal pattern repeat. Channel quilting is not suitable for linear patterns as quilting cannot follow on the stripe. We recommend Outline Quilting of plaids, checks and stripes, or alternatively, Frame Quilting. Thread colour – black or natural; BQ Design will select the most suitable.

Outline Quilting – Outline florals (traces the design on patterned florals – suitable for continuous stitching patterns only), plaids and checks. Outline Channels – recommended for striped fabrics. All outline quilting threads are colour matched to background colour.

Reverse Sham80-85cm length is standard. BQ Design recommends 100cm for double pillows.

Split CornersTo accommodate bed ends. Can be applied to throwover styles, whereby splits are concealed within the bell corners or tailored corner styles. These have several options: Split flaps, short flaps or no flaps/partly sewn down (to bracket connection point). See also “How to Measure”.

BedspreadsAll bedspread styles are interchangeable with quilting designs. Unquilted bedspreads are not recommended as they are prone to creasing and do not retain their shape after laundering. We suggest using bumph or 70 gram filling with a wide channel quilting e.g. 22.5cm, which gives a semi-quilted effect.

Filling100 gram is standard.

70 gram is recommended if lightweight option is required.

150 gram gives a lusher, puffier effect, but consideration should be given to the extra weight of the bedspread.

Bumph filling provides a soft, flat, unquilted look.Multi-Needle Quilting Machine

Frame Quilting Machine

Outline Quilting Machine

Wall Panels

Mounting Brackets Inset into the back of the framework so the wall panel sits flush with the wall. Covered with 200 gram polyester filling and fully upholstered, these slimline wall panels are lightweight and an effective alternative to bedheads or a stand-alone option.

ScotchgardTM Protector (“Scotchgard” is a trademark of the 3M Company)Repels spills and stains to keep furnishing items clean and looking new for longer.

B E D D I N G

15

Bedspread

1. Place pin on each side edge. Measure pin to pin = width

2. Place pin at head and foot. Measure pin to pin = length.

3. Measure pin 1 to floor = drop. Rolled edge style: add approx. 4cm to

drop measurement if roll is required to lay on floor

Cap

1. Step 1 and 2 as for bedspread.

3. Measure pin 1 to lower edge of mattress.

Add min. 10cm/max. 15cm to measurement i.e. mattress thickness plus

10cm/15cm = cap drop. (Cap should hang at least half way down the side

of the bed.)

Bed Valances

1. Step 1 and 2 as for bedspread.

3. Measure top edge of base to floor = valance drop.

Split Corners

If split corners are required for bed posts, measurements required:

1. Between brackets at attachment point.

2. Floor up to bracket.

N.B. For rolled edge style: if extra has been added for roll to lay on floor,

this allowance must be added to measurement 2

HOW TO MEASURE

1. Distance between splits

2. Distance up from floor

We invite you to visit BQ Design’s large, modern showroom to see the full range of products on display.

Alternatively, give one of our expert customer service staff a call and let them help advise you on your next stunning bedroom design.

Freecall 1800 335 361

Leaders in custom made soft furnishings

Documents

BQ Design Bedding Catalogue