EVALUATIONBILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalAll activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionESTIMATEYP SEATON% VARAREL% VARVTR% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)$42,699.13$75,193.02(76.10)$32,805.3923.17$36,601.4414.28Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))$7,000.00$13,994.55(99.92)$8,101.29(15.73)$9,586.21(36.95)3Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)$4,314.00$6,494.89(50.55)$2,985.4530.80$3,628.9815.884Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)$6,500.00$9,610.72(47.86)$5,999.977.69$6,570.37(1.08)5Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)$7,000.00$16,894.98(141.36)$8,605.80(22.94)$11,362.48(62.32)INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATS$3,575.00$6,632.50(85.52)$4,066.12(13.74)$8,364.72(133.98)7Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supply$3,835.00$5,997.98(56.40)$2,614.2031.83$6,957.21(81.41)8Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)9Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)10Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)$1,100.00$2,033.58(84.87)$2,031.69(84.70)$2,079.50(89.05)11Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)$1,225.00$2,324.14(89.73)$2,436.57(98.90)$2,615.20(113.49)13Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)$3,675.00$6,174.72(68.02)$9,383.36(155.33)$9,894.90(169.25)14Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.$100.00$6.7593.25$237.47(137.47)$78.2021.8015Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.$2,400.00$319.5286.69$350.8485.38$525.1678.1216Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)$3,350.00$2,434.9927.31$3,546.58(5.87)$3,111.507.1217Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)$4,020.00$2,921.9927.31$4,255.90(5.87)$3,733.807.1218Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)$4,690.00$3,408.9827.31$4,965.21(5.87)$4,356.107.1219Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)$5,360.00$3,895.9827.31$5,674.53(5.87)$4,978.407.1220Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)$6,030.00$4,382.9827.31$6,383.85(5.87)$5,600.707.1221Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)$6,700.00$5,222.4322.05$7,093.16(5.87)$6,223.007.1222Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)$7,370.00$5,744.6722.05$7,802.48(5.87)$6,845.307.1223Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)$8,375.00$6,528.0322.05$8,866.45(5.87)$7,778.757.1224Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,$173.00$80.9853.19$100.2942.03$241.94(39.85)25Supply and Install LED emergency Light System with 6 hrs run time$141.00$254.55(80.53)$130.587.39$164.46(16.64)Sub Total$134,532.13$188,998.97(40.49)$133,310.320.91$151,611.72(12.70)PRELIMINARIESSupervision$10,953.21$4,545.4558.50$1,770.8083.83$6,990.4536.18Commissioning$2,500.00$1,363.6445.45$885.4064.58$710.5371.58Provision for Government Electrical Inspector Certification$600.00$550.008.33$852.78(42.13)$498.5916.9027Contingincies$3,000.00$3,000.000.0$3,000.000.0$3,000.000.0Preliminaries Subtotal$17,053.21$9,459.0944.53$6,508.9861.83$11,199.5734.33Grand Total Total$151,585.34$198,458.06(30.92)$139,819.307.76$162,811.29(7.41)NoDescriptionESTIMATEYP SEATON% VARAREL% VARVTR% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)$42,699.13$75,193.02(76.10)$32,805.3923.17$36,601.4414.28Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))$7,000.00$13,994.55(99.92)$8,101.29(15.73)$9,586.21(36.95)3Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)$4,314.00$6,494.89(50.55)$2,985.4530.80$3,628.9815.884Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)$6,500.00$9,610.72(47.86)$5,999.977.69$6,570.37(1.08)5Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)$7,000.00$16,894.98(141.36)$8,605.80(22.94)$11,362.48(62.32)INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATS$3,575.00$6,632.50(85.52)$4,066.12(13.74)$8,364.72(133.98)7Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supply$3,835.00$5,997.98(56.40)$2,614.2031.83$6,957.21(81.41)8Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)9Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)10Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)$1,100.00$2,033.58(84.87)$2,031.69(84.70)$2,079.50(89.05)11Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)$1,225.00$2,324.14(89.73)$2,436.57(98.90)$2,615.20(113.49)13Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)$3,675.00$6,174.72(68.02)$9,383.36(155.33)$9,894.90(169.25)14Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.$100.00$6.7593.25$237.47(137.47)$78.2021.8015Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.$2,400.00$319.5286.69$350.8485.38$525.1678.1216Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)$3,350.00$2,434.9927.31$3,546.58(5.87)$3,111.507.1217Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)$4,020.00$2,921.9927.31$4,255.90(5.87)$3,733.807.1218Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)$4,690.00$3,408.9827.31$4,965.21(5.87)$4,356.107.1219Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)$5,360.00$3,895.9827.31$5,674.53(5.87)$4,978.407.1220Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)$6,030.00$4,382.9827.31$6,383.85(5.87)$5,600.707.1221Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)$6,700.00$5,222.4322.05$7,093.16(5.87)$6,223.007.1222Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)$7,370.00$5,744.6722.05$7,802.48(5.87)$6,845.307.1223Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)$8,375.00$6,528.0322.05$8,866.45(5.87)$7,778.757.1224Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,$173.00$80.9853.19$100.2942.03$241.94(39.85)25Supply and Install LED emergency Light System with 6 hrs run time$141.00$254.55(80.53)$130.587.39$164.46(16.64)Sub Total$134,532.13$188,998.97(40.49)$133,310.320.91$151,611.72(12.70)PRELIMINARIESSupervision$10,953.21$4,545.4558.50$1,770.8083.83$6,990.4536.18Commissioning$2,500.00$1,363.6445.45$885.4064.58$710.5371.58Provision for Government Electrical Inspector Certification$600.00$550.008.33$852.78(42.13)$498.5916.9027Contingincies$3,000.00$3,000.000.0$3,000.000.0$3,000.000.0Preliminaries Subtotal$17,053.21$9,459.0944.53$6,508.9861.83$11,199.5734.33Grand Total Total$151,585.34$198,458.06(30.92)$139,819.307.76$162,811.29(7.41)NoDescriptionESTIMATEYP SEATON% VARAREL% VARVTR% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)$42,699.13$75,193.02(76.10)$32,805.3923.17$36,601.4414.28Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))$7,000.00$13,994.55(99.92)$8,101.29(15.73)$9,586.21(36.95)3Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)$4,314.00$6,494.89(50.55)$2,985.4530.80$3,628.9815.884Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)$6,500.00$9,610.72(47.86)$5,999.977.69$6,570.37(1.08)5Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)$7,000.00$16,894.98(141.36)$8,605.80(22.94)$11,362.48(62.32)INSTALLATION$67,019.00$66,810.81(0.31)$74,812.4211.63$83,862.2425.13NoDescriptionESTIMATEYP SEATON% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)Equipment summary$42,699.13$75,193.0276.10Distribution Panel2Four Electrical Panel with Circuit breakers2481446995.14Distribution Panels summary$24,814.00$46,995.1489.39INSTALLATION3Installation of varying sizes of Electrical ConductorsInstallation summary$67,019.00$66,810.81(0.31)PRELIMINARIES4Supervion, commissioning and certificationPreliminaries summary$14,053.21$6,459.09(54.04)NoDescriptionESTIMATEAREL% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)Equipment summary$42,699.13$32,805.39(23.17)Distribution Panel2Four Electrical Panel with Circuit breakersDistribution Panels summary$24,814.00$25,692.513.54INSTALLATION3Installation of varying sizes of Electrical ConductorsInstallation summary$67,019.00$74,812.4211.63PRELIMINARIES4Supervion, commissioning and certificationPreliminaries summary$14,053.21$3,508.98(75.03)NoDescriptionESTIMATEVTR% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)Equipment summary$42,699.13$36,601.44(14.28)Distribution Panel2Four Electrical Panel with Circuit breakersDistribution Panels summary$24,814.00$31,148.0425.53INSTALLATION3Installation of varying sizes of Electrical ConductorsInstallation summary$67,019.00$83,862.2425.13PRELIMINARIES4Supervion, commissioning and certificationPreliminaries summary$14,053.21$8,199.57(41.65)

COMPARISONBILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalAll activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionESTIMATEYP SEATON% VARAREL% VARVTR% VAREquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)$42,699.13$75,193.02(76.10)$32,805.3923.17$36,601.4414.28Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))$7,000.00$13,994.55(99.92)$8,101.29(15.73)$9,586.21(36.95)3Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)$4,314.00$6,494.89(50.55)$2,985.4530.80$3,628.9815.884Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)$6,500.00$9,610.72(47.86)$5,999.977.69$6,570.37(1.08)5Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)$7,000.00$16,894.98(141.36)$8,605.80(22.94)$11,362.48(62.32)INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATS$3,575.00$6,632.50(85.52)$4,066.12(13.74)$8,364.72(133.98)7Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supply$3,835.00$5,997.98(56.40)$2,614.2031.83$6,957.21(81.41)8Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)9Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)$2,450.00$4,223.02(72.37)$2,436.570.55$5,156.70(110.48)10Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)$1,100.00$2,033.58(84.87)$2,031.69(84.70)$2,079.50(89.05)11Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)$1,225.00$2,324.14(89.73)$2,436.57(98.90)$2,615.20(113.49)13Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)$3,675.00$6,174.72(68.02)$9,383.36(155.33)$9,894.90(169.25)14Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.$100.00$6.7593.25$237.47(137.47)$78.2021.8015Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.$2,400.00$319.5286.69$350.8485.38$525.1678.1216Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)$3,350.00$2,434.9927.31$3,546.58(5.87)$3,111.507.1217Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)$4,020.00$2,921.9927.31$4,255.90(5.87)$3,733.807.1218Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)$4,690.00$3,408.9827.31$4,965.21(5.87)$4,356.107.1219Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)$5,360.00$3,895.9827.31$5,674.53(5.87)$4,978.407.1220Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)$6,030.00$4,382.9827.31$6,383.85(5.87)$5,600.707.1221Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)$6,700.00$5,222.4322.05$7,093.16(5.87)$6,223.007.1222Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)$7,370.00$5,744.6722.05$7,802.48(5.87)$6,845.307.1223Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)$8,375.00$6,528.0322.05$8,866.45(5.87)$7,778.757.1224Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,$173.00$80.9853.19$100.2942.03$241.94(39.85)25Supply and Install LED emergency Light System with 6 hrs run time$141.00$254.55(80.53)$130.587.39$164.46(16.64)Sub Total$134,532.13$188,998.97(40.49)$133,310.320.91$151,611.72(12.70)PRELIMINARIESSupervision$10,953.21$4,545.4558.50$1,770.8083.83$6,990.4536.18Commissioning$2,500.00$1,363.6445.45$885.4064.58$710.5371.58Provision for Government Electrical Inspector Certification$600.00$550.008.33$852.78(42.13)$498.5916.9027Contingincies$3,000.00$3,000.000.0$3,000.000.0$3,000.000.0Preliminaries Subtotal$17,053.21$9,459.0944.53$6,508.9861.83$11,199.5734.33Grand Total Total$151,585.34$198,458.06(30.92)$139,819.307.76$162,811.29(7.41)

RVE May 4BILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalDate: May 7, 2015 Rev 1All activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionUnitQtyMaterial CostLabour CostExtended CostEquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)ea80.00.00.0Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))ea10.00.00.03Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)ea10.00.00.04Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)ea10.00.00.05Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)ea20.00.00.0INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATSM130.00.00.07Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supplyM130.00.00.08Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)M100.00.00.09Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)M100.00.00.010Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)M100.00.00.011Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)M100.00.00.013Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)M3014Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.M50.00.00.015Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.Lot1$$$16Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)M500.00.00.017Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)M600.00.00.018Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)M700.00.00.019Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)M800.00.00.020Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)M900.00.00.021Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)M1000.00.00.022Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)M1100.00.00.023Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)M1250.00.00.024Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,Lot10.00.00.025Supply and Install LED emergency Light System with 6 hrs run timeLot10.00.00.026Provision for Government Electrical Inspector certificationLot10.00.00.0Sub TotalPRELIMINARIESSupervisionLot10.00.00.0CommissioningLot10.00.00.0Provision for Government Electrical Inspector CertificationLot10.00.00.027Contingincies0.00.0$300,000.00Preliminaries Subtotal0.0GCT0.0Grand Total Total0.0

YP SeatonBILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalDate: May 7, 2015 Rev 1All activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionUnitQtyMaterial CostLabour CostExtended CostEquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)ea8$6,914.21$2,484.91$75,192.96$75,193.02Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))ea1$10,372.74$3,621.82$13,994.56$13,994.553Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)ea1$4,814.00$1,680.89$6,494.89$6,494.894Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)ea1$7,123.45$2,487.27$9,610.72$9,610.725Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)ea2$6,261.26$2,186.23$16,894.98$16,894.98INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATSM13$456.05$54.14$6,632.47$6,632.507Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supplyM13$447.65$13.73$5,997.94$5,997.988Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)M10$368.16$54.14$4,223.00$4,223.029Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)M10$368.16$54.14$4,223.00$4,223.0210Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)M10$149.22$54.14$2,033.60$2,033.5811Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)M10$178.27$54.14$2,324.10$2,324.1413Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)M30$148.22$57.61$6,174.90$6,174.7214Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.M5$1.21$0.14$6.75$6.7515Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.Lot1$236.83$82.69$319.52$319.5216Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)M50$37.74$10.96$2,435.00$2,434.9917Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)M60$37.74$10.96$2,922.00$2,921.9918Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)M70$37.74$10.96$3,409.00$3,408.9819Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)M80$37.74$10.96$3,896.00$3,895.9820Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)M90$37.74$10.96$4,383.00$4,382.9821Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)M100$37.74$14.49$5,223.00$5,222.4322Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)M110$37.74$14.49$5,745.30$5,744.6723Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)M125$37.74$14.49$6,528.75$6,528.0324Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,Lot1$60.02$20.96$80.98$80.9825Supply and Install LED emergency Light System with 6 hrs run timeLot1$181.82$72.73$254.55$254.55Sub Total$189,000.97$188,998.97PRELIMINARIESSupervisionLot10.00.0$4,545.45CommissioningLot10.00.0$1,363.64Provision for Government Electrical Inspector CertificationLot10.00.0$550.0027Contingincies0.00.0$3,000.00Preliminaries Subtotal$9,459.09Grand Total$198,460.06$198,458.06Diff$(2.00)

ARELBILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalDate: May 7, 2015 Rev 1All activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionUnitQtyMaterial CostLabour CostExtended CostEquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)ea8$3,768.65$332.03$32,805.4432805.39Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))ea1$6,330.49$1,770.80$8,101.29$8,101.293Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)ea1$2,542.75$442.70$2,985.45$2,985.454Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)ea1$4,671.87$1,328.10$5,999.97$5,999.975Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)ea2$3,638.85$664.05$8,605.80$8,605.80INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATSM13$282.90$29.88$4,066.14$4,066.127Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supplyM13$178.82$24.35$2,641.21$2,614.208Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)M10$215.99$27.67$2,436.60$2,436.579Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)M10$215.99$27.67$2,436.60$2,436.5710Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)M10$178.82$24.35$2,031.70$2,031.6911Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)M10$215.99$27.67$2,436.60$2,436.5713Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)M30$282.90$29.88$9,383.40$9,383.3614Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.M5$47.27$0.22$237.45237.4715Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.Lot1$262.30$88.54$350.84$350.8416Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)M50$51.01$19.92$3,546.50$3,546.5817Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)M60$51.01$19.92$4,255.80$4,255.9018Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)M70$51.01$19.92$4,965.10$4,965.2119Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)M80$51.01$19.92$5,674.40$5,674.5320Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)M90$51.01$19.92$6,383.70$6,383.8521Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)M100$51.01$19.92$7,093.00$7,093.1622Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)M110$51.01$19.92$7,802.30$7,802.4823Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)M125$51.01$19.92$8,866.25$8,866.4524Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,Lot1$56.02$44.27$100.29$100.2925Supply and Install LED emergency Light System with 6 hrs run timeLot1$86.31$44.27$130.58$130.58Sub Total$133,336.41$133,310.32PRELIMINARIESSupervisionLot10.00.0$1,770.80CommissioningLot10.00.0$885.40Provision for Government Electrical Inspector CertificationLot10.00.0$852.7827Contingincies0.00.0$3,000.00Preliminaries Subtotal$6,508.98GCTGrand Total$139,845.39$139,819.30Diff$(26.09)

VTRBILL OF QUANTITYEQUIPMENT & ELECTRICAL INSTALLATIONProject: Installation of 32 Additional Reefer Outlets at the Montego Bay Cargo TerminalDate: May 7, 2015 Rev 1All activities are in reference to the One Line Diagram provided. Installation are to be in conformance with the JS21 Electrical CodesNoDescriptionUnitQtyMaterial CostLabour CostExtended CostEquipment1Supply and Installation of ESL 4-Gang Pedestal Mount Safety-Interlocked Power Module for Reefer. Cat. No. E4-R32-480-30-22SDSC-SP-220679A (Available from ESL Power Systems - www.eslpwr.com)ea8$4,175.18$400.00$36,601.44Distribution Panel2Supply and install a 1200 Amp rated Panel Board with 1000 Amp TP CB as Main; 1- 800 A TP and 1-400A TP sub ( See Single-Line Diagram))ea1$8,586.21$1,000.00$9,586.213Supply and install a 800Amp Triple pole Main Generator Breaker and enclosure for the incoming Generator power.( See Single-Line drawing)ea1$3,378.98$250.00$3,628.984Supply and install Distribution Board "A" complete with 800 amp TP Main Breaker, 2 -400amp. 1- 20amp SP Sub-breaker. (See Single Line Drawing)ea1$5,996.33$574.04$6,570.375Supply and install sub-panel A1 and A2, each complete with 1- 400 amp TP Main Breaker, 4 - 125amp TP Sub-breaker. (see drawings)ea2$5,081.24$600.00$11,362.48INSTALLATION6Supply and Install 2-4/C 240mm2 cable (XLPE) + Ground from the load side of the Generator to Generator circuit breaker then to the ATSM13$579.85$63.59$8,364.727Supply and Install 3-4/C 150mm2 XLPE cable + Ground from the LV side of the 750kVA Transformer to the 1000Amp Main Breaker for the JPS supplyM13$458.32$76.85$6,957.218Install 2-4/C 185mm2 XLPE cable from the load side of the 800amp Main Breaker to the existing Automatic Transfer Switch (ATS) (see drawing)M10$457.05$58.62$5,156.709Install 2-4/C 185mm2 XLPE cable from the load side of the Automatic Transfer Switch (ATS) to the 800amp main panel board (see drawing)M10$457.05$58.62$5,156.7010Supply and install 150mm2 cable 1 - 4/C + G cable from 400 amp Sub Breaker in Main panel "A" to Sub - Panel A1 (See Drawings)M10$181.34$26.61$2,079.5011Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Sub-Panel A2 (See Drawings)M10$228.52$33.00$2,615.2013Supply and install 185mm2 1-4/C + G XLPE cable from 400Amp Sub breaker in main panel "A" to Pothead for existing reefer circuit (See Drawings)M30$289.83$40.00$9,894.9014Supply and install 2.5mm2 3-1/C cable from 20 Amp breaker in main panel to roof lights.M5$6.14$9.50$78.2015Supply and install 1, 600MCM bare copper cable to establish earthing, using a minimum of two earth electrodes.Lot1$406.74$118.42$525.1616Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 1 (conduits in place)M50$51.58$10.65$3,111.5017Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 2 (conduits in place)M60$51.58$10.65$3,733.8018Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 3 (conduits in place)M70$51.58$10.65$4,356.1019Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 4 (conduits in place)M80$51.58$10.65$4,978.4020Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 5 (conduits in place)M90$51.58$10.65$5,600.7021Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 6 (conduits in place)M100$51.58$10.65$6,223.0022Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 7 (conduits in place)M110$51.58$10.65$6,845.3023Supply and install 35mm2 1-4/C + G cable from 125Amp breaker in panel A1to Reefer Pedestal # 8 (conduits in place)M125$51.58$10.65$7,778.7524Supply and install double florescent fixture, complete with 40Watt Daylight tube and NEMA Switch,Lot1$171.76$70.18$241.9425Supply and Install LED emergency Light System with 6 hrs run timeLot1$104.46$60.00$164.46Sub Total$151,611.72PRELIMINARIESSupervisionLot10.0$6,990.45$6,990.45CommissioningLot10.0$710.53$710.53Provision for Government Electrical Inspector CertificationLot10.0$498.59$498.5927Contingincies0.00.0$3,000.00Preliminaries Subtotal$11,199.57Grand Total$162,811.29