Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
page(866) GO-BOINK 24 Hour Support Help Desk
BoinkKiosk System
AdministrationManual
®
Last updated on May 21st, 2002
(866) GO-BOINK 24 Hour Support Help Desk
page(866) GO-BOINK 24 Hour Support Help Desk
Table of ContentsINTRODUCTIONBoink Kiosk System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
KIOSK SYSTEM NORMAL OPERATIONSF6 Kiosk
General DescriptionFront. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Rear Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Inner Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Magnetic Card ReaderGeneral Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bill AcceptorGeneral description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8To Empty Bill Acceptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Bill Acceptor Jamming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Coin AcceptorGeneral description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17To Empty the Coin Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PrinterChanging the printer's paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Touch ScreenCleaning the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Back-lit Advertising ModuleChanging the Fluorescent Light . . . . . . . . . . . . . . . . . . . . . . . . . 25
Z3 KioskGeneral Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Bill Dispenser
Refilling the Bill Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Coin Hoppers
Refilling the Coin Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
BOINK SERVICE PROCEDURESCoin Acceptor Jamming
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Bill Dispenser Jamming
Physical Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38HAWK Diagnostic Software procedures . . . . . . . . . . . . . . . . . . 40
Pick Sensor Failure procedure. . . . . . . . . . . . . . . . . . . . 42Lost Bill on Exit procedure . . . . . . . . . . . . . . . . . . . . . . . 43
HAWK HAWK
1
page(866) GO-BOINK 24 Hour Support Help Desk
®Boink Kiosk System
BOM(Box Office Manager)- Controls all SF6 kioskthrough the BKCP (Kiosk Control Panel) software- Hosts the Transaction Database Server- Connects to the Movie Database Server
SF-6(Client Kiosk)- Receives the product information from the client through a graphic interface application- Holds all payment devices
Z-3(Dispensing Kiosk)- Controlled by the SF-6 kiosk- Holds al cash dispensing devices
FRONT VIEW SIDE VIEWREAR VIEW REAR VIEW
Change
page(866) GO-BOINK 24 Hour Support Help Desk
®Boink Kiosk System
BOM(Box Office Manager)- Controls all SF6 kioskthrough the BKCP (Kiosk Control Panel) software- Hosts the Transaction Database Server- Connects to the Movie Database Server
SF-6(Client Kiosk)- Receives the product information from the client through a graphic interface application- Holds all payment devices
Z-3(Dispensing Kiosk)- Controlled by the SF-6 kiosk- Holds al cash dispensing devices
FRONT VIEW SIDE VIEWREAR VIEW REAR VIEW
Change
2
page(866) GO-BOINK 24 Hour Support Help Desk
Our SF6 Kiosk is built with 16-calibre high security steel complying with ISO9001 quality regulations.
volt outlet 110/120110/120
The removal of the power plate may expose you to live voltage terminals.
To reduce the potential of a shock, our kiosks have a polarized plug (one grounded blade), which will fit only one way in a polarized outlet.
Never use this plug with an extension cord unless it fits properly.
Our kiosks are designed to use 110/120 volt outlets.
®Boink Kiosk System
Safety Precautions
3
page(866) GO-BOINK 24 Hour Support Help Desk
SPEAKERS
TICKETRECEPTACLE
SURVEILLANCECAMERA
BILLACCEPTOR
COINACCEPTOR
CARDREADER
MONITORFRAME
TOUCHSCREEN
BACK-LITADVERTISING
MODULE
TOP MONITOR
BOTTOMMONITOR
SF-6SF-6 General Description
Front
4
page(866) GO-BOINK 24 Hour Support Help Desk
SF-6 General Description
Rear Doors
For daily operations &maintenance procedures
Boink ServicePersonnel ONLY!
SF-6
5
page(866) GO-BOINK 24 Hour Support Help Desk
PRINTER
FAN
POWER PLATE
BILL ACCEPTOR
COIN ACCEPTOR
COIN BOX
CPU
CARDREADER
TOP MONITOR
BOTTOMMONITOR
SF-6SF-6 General Description
Inner Devices
6
page(866) GO-BOINK 24 Hour Support Help Desk
SF-6 General Description
Magnetic Card Reader
The Magnetic Card Reader accepts all credit and debit cards. It has two top mounted reader heads and thus will read any card inserted with its magnetic stripe towards the top.
SF-6
7
page(866) GO-BOINK 24 Hour Support Help Desk
The bill acceptor unit is composed of an electronic acceptance unit and a detachable Bill Stacker. It accepts $1, $5,$10, $20, $50 and $100 U.S. dollars bills. They can be inserted four ways, in any direction.
SF-6Bill Acceptor
Bill Stacker
8
page(866) GO-BOINK 24 Hour Support Help Desk
Open the Component Access Door1
2
3
Ident i fy t he B i l l Acceptor Tray
Pull out the bill tray
SF-6Bill Acceptor Procedures
To Empty the Bill Acceptor
BILL ACCEPTOR
9
page(866) GO-BOINK 24 Hour Support Help Desk
Take the bill stacker with both hands
6
4
5
6
Press the release pegs and take out the bill stacker.
Open the bill stacker by rotating its lock handle counterclock-wise
SF-6
10
Bill Acceptor Procedures
To Empty the Bill Acceptor
page(866) GO-BOINK 24 Hour Support Help Desk
Open the bill stacker door7
8
9
Take out the bills
Close the stacker by rotating its lock handle clockwise
SF-6
11
Bill Acceptor Procedures
To Empty the Bill Acceptor
page(866) GO-BOINK 24 Hour Support Help Desk
Re-insert the bill stacker. Push it gently from below until it clicks...
10
11
12
... you should hear a mechanical noise if the stacker is correctly inserted.
Push the tray inside the kiosk until it clicks in place. Make sure it is fully inserted.
SF-6
12
Bill Acceptor Procedures
To Empty the Bill Acceptor
page(866) GO-BOINK 24 Hour Support Help Desk
SF-6Bill Acceptor Procedures
Bill Acceptor Jamming
Open the Component Access Door1
2
3
Ident i fy t he B i l l Acceptor Tray
Pull out the bill tray
BILL ACCEPTOR
13
page(866) GO-BOINK 24 Hour Support Help Desk
Take the bill stacker with both hands
6
4
5
6
Press the release pegs and take out the bill stacker.
14
SF-6Bill Acceptor Procedures
Bill Acceptor Jamming
Open the device by pushing the button on its upper side.
page(866) GO-BOINK 24 Hour Support Help Desk
SF-6Bill Acceptor Procedures
Bill Acceptor Jamming
7
8
9
Take the jammed Bill off.
Dry the inside with a compressed air can.
Close the device by pushing the upper button down, and closing gently the doors.
15
page(866) GO-BOINK 24 Hour Support Help Desk
SF-6Bill Acceptor Procedures
Bill Acceptor Jamming
Re-insert the bill stacker. Push it gently from below until it clicks...
10
11
12
... you should hear a mechanical noise if the stacker is correctly inserted.
Push the tray inside the kiosk until it clicks in place. Make sure it is fully inserted.
16
page(866) GO-BOINK 24 Hour Support Help Desk
The coin acceptor unit is composed of an electronic acceptance unit and a coin box placed underneath the unit. It accepts 5 cents, Dimes, Quarters and 1 dollar coins.
Coin Acceptor SF-6
rejectedcoins
accepted coins
17
page(866) GO-BOINK 24 Hour Support Help Desk
Open the Component Access Door1
2
3
Identify the Coin box
Pull out the Coin box
SF-6Coin Acceptor Procedures
To Empty the Coin Box
18
page(866) GO-BOINK 24 Hour Support Help Desk
Empty the Coin box by turning it upside down.
4
5 Push the Coin box back into its original position. Push it all the way in!
SF-6Coin Acceptor Procedures
To Empty the Coin Box
19
page(866) GO-BOINK 24 Hour Support Help Desk
Open the Component Access Door.1
2
3
Identify the printer tray and pull it.
Pull up the blue lever found on the left side of the printer. This releases the paper.
SF-6Printer Procedures
Changing the Printer's Paper
20
page(866) GO-BOINK 24 Hour Support Help Desk
Pull out the old paper roll.4
5
6
Remove the paper roller from the paper roll.
Get a new paper roll and place the paper roller in it.
SF-6
21
Printer Procedures
Changing the Printer's Paper
page(866) GO-BOINK 24 Hour Support Help Desk
Place the paper roll in its original position. 7
8
9
Insert the end of the paper roll into the printer (about 2 inches). Make sure the paper rolls from the top.
Push down the blue lever back to its original position to secure the paper. If properly done, t he pape r w i l l be automatically fed into the printer and cut.
SF-6
22
Printer Procedures
Changing the Printer's Paper
page(866) GO-BOINK 24 Hour Support Help Desk
Test the printer by pressing the black test button, located in the left side of the printer.
10
11
12
Take the test paper from the front of the printer .
Push the tray back i n t o i t s o r i g i n a l position.
SF-6
23
Printer Procedures
Changing the Printer's Paper
page(866) GO-BOINK 24 Hour Support Help Desk
Touch Screen Procedures
Cleaning the Touch Screen SF-6
1
2
Take a cloth towel and apply a small amount of rubbing alcohol to it. Do not spray the screen directly. Do not use windex or other cleaning supplies.
C lean t he touch screen gently and uniformly until it is completely cleaned.
24
page(866) GO-BOINK 24 Hour Support Help Desk
Press the acrylic upwards, until it pops out and remove it from the unit.
1
2
3
Turn the fluorescent light counterclockwise to release it from its socket.
P u t i n a n e w fluorescent light and align its ends with the sockets perforations.
SF-6Back-Lit Advertising Module Procedures
Changing the Fluorescent Light
25
page(866) GO-BOINK 24 Hour Support Help Desk
Turn the fluorescent light clockwise to secure it in the socket. Make sure it lights up.
4
5Place the poster back in its original place.
SF-6
26
Back-Lit Advertising Module Procedures
Changing the Fluorescent Light
page(866) GO-BOINK 24 Hour Support Help Desk
Z-3 General Description Z-3
BILLREJECT BIN
TOP BILLTRAY
BOTTOM BILLTRAY
LEFTCOIN HOPPER
RIGHTCOIN HOPPER
27
page(866) GO-BOINK 24 Hour Support Help Desk
1
2
3
Locate the bill reject bin
Lift the green lever to release the reject bin and pull it out
Empty its contents. and make sure to push it back into position until it clicks in place.
Z-3Bill Dispenser Procedures
Refilling the Bill Dispenser
28
page(866) GO-BOINK 24 Hour Support Help Desk
Locate the Bill tray on the Z-3's Back.
Only empty one bill tray at a time. Bill trays must not get placed in the wrong bin, as this would cause the machine to dispense the wrong currency !
Z-3
4
5
6 Lift the green lever with your r ight hand to release the cassette, while at the same time, with your left hand, gently pull out the cassette
XX
29
Bill Dispenser Procedures
Refilling the Bill Dispenser
page(866) GO-BOINK 24 Hour Support Help Desk
Open the tray lid.
Make sure all the bills are in good condition and have no folded edges. If there are bills in bad condition put them in the reject bin.
Z-3
7
8
9 Make sure there aren't any paper clips, staples, taped or torn bills in the stack you are about to insert.
30
Bill Dispenser Procedures
Refilling the Bill Dispenser
page(866) GO-BOINK 24 Hour Support Help Desk
Place the bills on the tray by lifting gently and pulling back the pusher to make room for the bills. After the bills are placed, release the pusher.
Z-3
10
11
12
Locate the reject bin on the Z-3 and put all the damaged bills there.
Arrange the bills so they are all properly aligned. Take your t ime to do this carefully!
31
Bill Dispenser Procedures
Refilling the Bill Dispenser
page(866) GO-BOINK 24 Hour Support Help Desk
Z-3
13
14
15
The tray's lid can easily jam and not c l o s e p r o p e r l y . Please make sure that it is completely closed before reinserting it.
X
Put the cassette back into its place. Make sure the bill tray goes into its proper denomina-tion slot.
Close the lid
32
Bill Dispenser Procedures
Refilling the Bill Dispenser
page(866) GO-BOINK 24 Hour Support Help Desk
Coin Hopper Procedures
Refilling the Coin Hopper Z-3
Open the Z-3 back door1
2
3
Identify the coin hopper.
Insert the coins in the hopper.
Inserting the wrong coins will cause t h e m a c h i n e t o dispense the wrong currency amount and m a y d a m a g e t h e hopper.
33
page(866) GO-BOINK 24 Hour Support Help Desk
BoinkService
Procedures
®
34
*Do not do these proceduresunless you have been
previously trained
page(866) GO-BOINK 24 Hour Support Help Desk
Open the Component Access Door1
2
3
Loca te t he co in acceptor
Remove the coin acceptor by pulling up the safety tab of the device. Be very careful, as it can break easily.
Coin Acceptor Jamming SF-6
35
page(866) GO-BOINK 24 Hour Support Help Desk
4
5
6
SF-6Coin Acceptor Jamming
Unplug the co in acceptor before taking it out.
Find the cover of the device where the coins are inserted, and pull it to release the jammed coin.
Take out the jammed coin and place the device again in the kiosk.
36
page(866) GO-BOINK 24 Hour Support Help Desk
7
8
Coin Acceptor Jamming SF-6
R e - c o n n e c t t h e cable.
Place the device back i n t o i t s o r i g i n a l position.
37
page(866) GO-BOINK 24 Hour Support Help Desk
Z-3Bill Dispenser Jamming
1
2
3
Open the Z-3's Back Door
Pull out both bill cassettes and the reject bin
Pull out the bi l l dispenser tray
38
page(866) GO-BOINK 24 Hour Support Help Desk
Turn the bill dispenser knob counter clock-wise to extract the jammed bills...
Until they fall in the reject bin.
Check that the rubber bands are completely clear and in place. If the bands fall off their gears STOP! Call (866) GO-BOINK
4
5
6
39
Z-3Bill Dispenser Jamming
page(866) GO-BOINK 24 Hour Support Help Desk
Z-3
Press the Debug Multi Pick Button or the F2 key
Press the Multi Purge Button or the F2 key.
Bill Dispenser Jamming
R u n t h e H A W K diagnostic program7
8
9
40
page(866) GO-BOINK 24 Hour Support Help Desk
I f t h e r e p o r t i s Operation Comple-ted Successfully, go to s tep 19 ( tes t dispense)
If the report is Pick Sensor Failure, go to step 13
If the report is Lost Bill on Exit, go to step 16
10
11
12
Z-3Bill Dispenser Jamming
41
page(866) GO-BOINK 24 Hour Support Help Desk
PICK SENSOR FAILURE
Clean the sensors and vacuum pumps w i t h i s o p r o p y l i c alcohol wet towels
Dry the inside with a compressed air can
Repeat the Multi Purge Operation (F2) u n t i l i t r e p o r t s Operation Comple-ted Successfully. Then, go to step 19.
13
14
15
Z-3Bill Dispenser Jamming
42
page(866) GO-BOINK 24 Hour Support Help Desk
16
17
18
LOST BILL ON EXIT
Pull out the Bil l Dispenser tray.
Turn the green knob counter clockwise to send any jammed bill to the reject bin
Remove any jammed bills found on the Bill Dispenser Exit. Then go to step 19.
Z-3Bill Dispenser Jamming
43
page(866) GO-BOINK 24 Hour Support Help Desk
TEST DISPENSE
Press the Dispense Options or the F1 Key
P r e s s t h e Te s t Dispense Button or the F2 Key
Write 1 1 0 0 in the dialog box, which means "Dispense 1 bill from the first cassette, 1 bill from the second, and no bills from third and fourth cassette". Press OK
1 1 0 0
19
20
21
Z-3Bill Dispenser Jamming
44
page(866) GO-BOINK 24 Hour Support Help Desk
Z-3Bill Dispenser Jamming
If Test Dispense was successful you will find the dispensed bills in the Reject Bin. Check that you got one from each tray.
The report must show Operation Comple-ted Successfully
22
23
24
45
C l o s e t h e B i l l Dispenser Tray and close the Z-3's back door