Blohm + Voss PSH 150 Power SlipV... · Blohm + Voss PSH 150 Power Slip for 2 3/8” – 7 5/8” Rotary Standard Slips Hydraulic Operated P/N 88210-H Hydraulic Operated with Feedback

TECHNICAL DOCUMENTATION PSH 150

1

Blohm + Voss PSH 150 Power Slip

for

2 3/8” – 7 5/8” Rotary Standard Slips

Hydraulic Operated P/N 88210-H

Hydraulic Operated with Feedback P/N 88210-H-F

READ THIS INSTRUCTION BEFORE USE


2

Blohm + Voss Oil Tools Herrmann-Blohm-Straße 2 20457 Hamburg • Germany

Telephone +49 (0)40/3119-1139 • Fax +49 (0)40/3119-3305

88210-H-F-D Rev003, February 2012

All rights retained. No part of this document may be reproduced in any form (print, photocopy, microfilm or any other procedure) or be processed using an electronic system without written approval of Blohm + Voss Oil Tools

Dependent on ongoing technical improvements (ISO 9001) “B+V Oil Tools“ reserves the right to be able to change the design and specifications without previous announcement. The values specified represent the nominal values of a unit

produced in series production. Slight deviations in the case of the individual devices are possible.


3

Content

1 General Warnings ....................................................................................................5

2 Introduction..............................................................................................................7

3 Technical Data of Power Slip PSH 150 ..................................................................9

3.1 Dimensions................................................................................................................................. 9 3.2 Slip Adapter ................................................................................................................................ 9 3.3 Power Required.......................................................................................................................... 9 3.4 Identification............................................................................................................................... 9 3.5 Rotary Table ............................................................................................................................. 10

4 Installation and Operation ....................................................................................11 4.1 Installation ................................................................................................................................ 11 4.2 Hydraulic System..................................................................................................................... 13

4.2.1 Venting .............................................................................................................................. 13 4.2.2 Connect the PSH with Hydraulic Supply ........................................................................... 13 4.2.3 Schematic Hydraulic without Feedback ............................................................................ 14 4.2.4 Schematic Hydraulic with Feedback ................................................................................. 15 4.2.5 Hydraulic valve for Feedback............................................................................................ 15 4.2.6 Hydraulic valve settings and adjustment........................................................................... 16

4.3 Manual Adjustments ................................................................................................................ 18 4.3.1 Manual Lifting in Case of an Emergency........................................................................... 18

5 Lubrication .............................................................................................................19

6 Inspections.............................................................................................................21

6.1 Routine – Daily Field Inspection............................................................................................. 21 6.2 Semi - Annual Field Inspection.............................................................................................. 21 6.3 Inspection ................................................................................................................................. 21 6.4 Inspection of Hydraulic System.............................................................................................. 21 6.5 Dismantling Inspection............................................................................................................ 21

7 Maintenance and Repair .......................................................................................27

8 Principle Drawings and Part List for Power Slip PSH 150.................................28

8.1 PS Assembly without Feedback, Exploded View, P/N 88210-H........................................... 28 8.2 PS Assembly without Feedback, P/N 88210-H ...................................................................... 29 8.3 PS Assembly with Feedback, Exploded View, P/N 88210-H-F ............................................. 31 8.4 PS Hydraulic Assembly without Feedback, Exploded View, P/N 88229-H ......................... 34 8.5 PS Hydraulic Assembly without Feedback, P/N 88229-H..................................................... 35 8.6 PS Hydraulic Assembly with Feedback, P/N 88229-H-F ....................................................... 36 8.7 Quick Lock Pin Assembly, P/N 88240 .................................................................................... 39 8.8 Protection Plate Assembly, P/N 88224................................................................................... 41

9 Spare Parts List (2 Years operation)....................................................................43

9.1 88210-H-RSP for PSH 150-Hydraulic without Feedback....................................................... 43 9.2 88210-H-F-RSP for PSH 150-Hydraulic with Feedback......................................................... 44

10 Address List .........................................................................................................45


4

Content of Figures Fig. 1 : Warning.....................................................................................................................5 Fig. 2 : Caution information...................................................................................................5 Fig. 3 : Danger information....................................................................................................6 Fig. 4 : Power Slip installed with Master Bushing and Rotary Slip ........................................7 Fig. 5 : Power Slip installed with Master Bushing and Rotary Slip (Top view ). Slip Up. .......8 Fig. 6 : Power Slip installed with Master Bushing and Rotary Slip (Top view ). Slip Down. ..8 Fig. 7 : Identification Plate PSH 150 without Feedback ........................................................9 Fig. 8 : Identification Plate PSH 150 with Feedback .............................................................9 Fig. 9 : Punch Diameter of Rotary Table.............................................................................10 Fig. 10 : Locking Assembly ..................................................................................................11 Fig. 11 : Locking Assembly, unlocked ( Vertical Position ) ...................................................11 Fig. 12 : Place the Power Slip on the Rotary Table...............................................................12 Fig. 13 : Locking Pin Assembly, locked ( Horizontal Position ).............................................12 Fig. 14 : Hydraulic Connections of PSH to Hydraulic Supply ...............................................13 Fig. 15 : Hydraulic Schematic without Feedback ..................................................................14 Fig. 16 : Hydraulic Schematic with Feedback .......................................................................15 Fig. 17 : Remove Protection Cover .......................................................................................17 Fig. 18 : Adjustment for Cylinder Power................................................................................17 Fig. 19 : Adjustment for Extending and Engaging Speed of Cylinder....................................18 Fig. 20 : Adjustment Screw ...................................................................................................18 Fig. 21 : Lift Up the Power Slip Manually ..............................................................................18 Fig. 22 : Lift Up......................................................................................................................19 Fig. 23 : Lift Down .................................................................................................................19 Fig. 24 : Lubrication points....................................................................................................20 Fig. 25 : Power Slip Assembly without Feedback .................................................................28 Fig. 26 : Power Slip Assembly without Feedback, Exploded View........................................28 Fig. 27 : Power Slip, Assembly Isometric..............................................................................29 Fig. 28 : Power Slip Assembly without Feedback .................................................................29 Fig. 29 : Power Slip Assembly with Feedback, Exploded View.............................................31 Fig. 30 : Power Slip, Hydraulic Assembly , Exploded View...................................................34 Fig. 31 : Power Slip without Feedback, Hydraulic Assembly ................................................35 Fig. 32 : Power Slip with Feedback, Hydraulic Assembly .....................................................36 Fig. 33 : Power Slip, Quick Lock Pin Assembly.....................................................................39 Fig. 34 : Power Slip, Quick Lock Pin Assembly, Exploded View...........................................39 Fig. 35 : Power Slip, Protection Plate Assembly ...................................................................41


5

1 General Warnings

Fig. 1 : Warning Fig. 2 : Caution information

DANGER For

repair or maintenance work disconnect hydraulic supply !

WARNING This product could be hazardous if improperly used. Misuse of this tool could cause serious

injury to personnel. This must be properly installed and maintained in first class condition. Do not remove or alter any parts. Do not weld or

alter without factory authorization. All replacement parts must be of

Blohm + Voss manufactured.

CAUTION Keep distance

from the Power Slip during operation and trials !


6

Fig. 3 : Danger information - All warning and safety labelling are attached to the equipment must be observed. - Keep distance from the Power Slip ( PSH 150 ) during operation and trials. - The PSH 150 must only be used for the designated purpose. - During normal operation with the power slip make sure that the rotary table is locked. The warranty providing will be void, if the Power Slip is either:

a) repaired or serviced by a service facility, which was not authorised by Blohm + Voss Repair GmbH b) replacement parts are used, which are not manufactured by Blohm + Voss Oil Tools c) modifications were made by the Power slip, which were not approved by Blohm + Voss Oil Tools


7

2 Introduction

The inspection and maintenance procedure is based on API – Recommended practice and Blohm+Voss Oil Tools experience in the design of slips. This recommended practice outlines are procedures for methods of inspection and maintenance of Power Slips to prevent injury to personnel and irreparable damage to equipment. This technical documentation contains instructions of safety, installation, operation and maintenance for the PSH 150. Throughout the documentation, the abbreviation PSH – F is used occasionally for the designation of the Power Slip with Feedback. In the event of problems, which cannot be solved with the aid of this manual, please contact one of the addresses list at the end of this documentation. The Blohm+Voss Type PSH 150 hydraulic operated Power Slip is designed for enhanced safety by eliminating personnel on the Rig floor, when operations are required the use of slips. The PSH 150 can be operated by using a Control Unit at a safe distance from the Rotary Table. In case of a loss of hydraulic pressure, a safety device is installed to prevent the lifting arm from engaging. The Power Slip accommodates B+V Standard ( Rotary ) Slips in the range of 2 3/8” to 7”, as well as most other brands.

Fig. 4 : Power Slip installed with Master Bushing and Rotary Slip


8

Fig. 5 : Power Slip installed with Master Bushing and Rotary Slip (Top view ). Slip Up. Fig. 6 : Power Slip installed with Master Bushing and Rotary Slip (Top view ). Slip Down.


9

3 Technical Data of Power Slip PSH 150

3.1 Dimensions

width 582 mm length 1320 mm height 540 mm

weight ( without Slips ) 270 kg 3.2 Slip Adapter

Hand slips are connected to the PSH with an Adapter (see Pos.16, page 28/29 slip Fastening Link). Two different Adapters are available: For B+V Slips: P/N 88208 For Access: P/N 88208-A 3.3 Power Required

Working pressure 120 - 210 bar / 2030 – 3045 PSI Flow rate 22,7 – 37,9 l / min / 6 – 10 GPM (is adjusted) Min. Flow rate 20 l / min / 5,4 GPM 3.4 Identification

You find the identification plate on the left side of Power Slip, when you look from behind the PSH 150.

Fig. 7 : Identification Plate PSH 150 without Feedback Fig. 8 : Identification Plate PSH 150 with Feedback

Part Number Part Number


10

3.5 Rotary Table

The Power Slip PSH 150 fits for all 37 ½“ rotary tables which are produced to API Standard following punch dimensions: Hole for the lock pin assembly from PSH 150

25

3/4

"

90°

Fig. 9 : Punch Diameter of Rotary Table


11

4 Installation and Operation

4.1 Installation (1) To install Power Slip: Tilt the Quick Locking Pin Assembly into vertical position first

Fig. 10 : Locking Assembly

Fig. 11 : Locking Assembly, unlocked ( Vertical Position )

unlocked

Notice: If the 4 mounting holes of master bushing are oversized for example by abrasion, it’s possible to regulate the Quick Locking Pin Assembly

Adjust the nut


12

(2) Place the Power Slip on the Rotary Table by lifting with a crane and close the Locking Assembly

Fig. 12 : Place the Power Slip on the Rotary Table

(3) Lock the Power Slip by turning the lever back in horizontal position

Fig. 13 : Locking Pin Assembly, locked ( Horizontal Position )

lock

ed

Tilt the Quick Locking Pin Assembly into vertical position

Fixing for the crane


13

4.2 Hydraulic System 4.2.1 Venting

At the beginning of work wear your personnel protection equipment. Especially leak oil under pressure can cause severe personnel injury to the eyes (use eye protection). The hydraulic system of delivered Power Slip is vented. Be aware that the hydraulic connection hoses (A,B and C) should be vented before connecting it to the power slip. If air has collected in the system, it can be discharged with the aid of the fittings near the couplings. 4.2.2 Connect the PSH with Hydraulic Supply

The PSH-150 hydraulic operated must be connected with the hydraulic supply by couplings (see Fig. 14). The connection “C” is only available for the PSH-150 with Feedback. Information on the end positions of the jib is transmitted to the “Control unit” through the built-in 2-way valves.

Fig. 14 : Hydraulic Connections of PSH-F to Hydraulic Supply

Description of the connections: A – Coupling screwed joint (male) for slips down B – Coupling screwed joint (female) for slip up

Connection C

Connection A

Connection B


14

P

T

T

P

B

PSH-150 hydraulic operatedwithout Feedback

A

A B

down up

Rotary Slip

Hydraulic block

Po

wer

Supp

ly

B

A

Valve No.1

Valve No.2

Valve No.5

Valve No.6

Valve No.4

Valve No.3

Set slips

Raise slips

C – Coupling screwed joint (male) for feedback (only 88210-H-F) 4.2.3 Schematic Hydraulic without Feedback

Fig. 15 : Hydraulic Schematic without Feedback

Valve No. 1: Throttle 1 Valve No. 2: Throttle 2 Valve No. 3: Excess pressure valve 1 Valve No. 4: Check Valve 1 Valve No. 5: Excess pressure valve 2 Valve No. 6: Check Valve 2


15

4.2.4 Schematic Hydraulic with Feedback

P

T

T

P

B

PSH-150 hydraulic operatedwith Feedback

A

A B

Po

we

rS

up

ply

B

A

down up

Rotary Slip

Hydraulic blockValve No.1

Valve No.2

Valve No.3

Valve No.4

a

R P

actuated when Slipare raised

1

2

3a

R P

actuated when Slipare set

C

Valve No.7 Valve No.8

Valve No.9

Feedback

sig

nal

Valve No.5

Valve No.6

Set slips

Raise slips

Fig. 16 : Hydraulic Schematic with Feedback

Valve No. 1: Throttle 1 Valve No. 7: 2-Way Valve 1 Valve No. 2: Throttle 2 Valve No. 8: 2-Way Valve 2 Valve No. 3: Excess pressure valve 1 Valve No. 9: Check Valve 3 Valve No. 4: Check Valve 1 Valve No. 5: Excess pressure valve 2 Valve No. 6: Check Valve 2 4.2.5 Hydraulic valve for Feedback

The PSH-F 150 is also equipped with two feedback valves (only 88210-H-F). Depending on the position of the jib, these valves pass a volume flow to the control unit which is then converted into a signal for the operator.


16

4.2.6 Hydraulic valve settings and adjustment

The hydraulic system of the PSH-150 hydraulic operated is tested and delivered fully functional with the specified hydraulic power requirements. In case during the commissioning no function or incomplete function occurs the following hydraulic settings can be checked. Any change of the settings were allowed only by B+V adjustments may result in damage or severe personal injury. 4.2.6.1 Warning Before any work is carried out wear your personal protection equipment. Especially leak oil under pressure can cause severe personal injury to the eyes. For adjustment work ensure that the quick disconnect couplings between the tool and control console are properly connected. 4.2.6.2 Detailed functional description hydraulic system Basis of the description is the hydraulic schematic Figure 15 / 16. Function: Pressure will be applied to the hydraulic operated Power Slip by using the hydraulic supply. Rotary Slip lift up and down Before operation of the PSH can be started, it must be properly installed into the rotary table. To raise the slip, line B is pressurized and to lower the slip, line A is pressurized with the hydraulic pressure specified in section 3.2. The hydraulic system has been optimally preset by Blohm+Voss GmbH and should not be changed. For the PSH with Feedback, a roller pushbutton valve is actuated in the upper and lower end position of the jib. Both valves pass the volume flow into the C line. Depending on where the pressure is applied, the operator receives a signal from the control unit allowing him to see whether the jib is up or down.


17

4.2.6.3 Basic hydraulic settings The basic setting guarantee a complete function of the Power Slip for 120 bar (2030 PSI) to 210 bar (3045 PSI) working pressure and 22,7 - 37,9 l/min (6 - 10 GPM) flow rate. It’s possible to regulate the engaging and extending speed or forces of hydraulic cylinders. That’s require when the flow rate or working pressure is lower than the adjusted power required. Procedure: 1. Disconnecting the 4 fixing screws and remove the protection cover of hydraulic block

Fig. 17 : Remove Protection Cover

2. Adjustment for Cylinder Power

Fig. 18 : Adjustment for Cylinder Power

Protection Cap of hydraulic block

Fixing screws

Excess pressure valve 1

Excess pressure valve 2


18

3. Adjustment for Extending and Engaging speed of cylinder

Fig. 19 : Adjustment for Extending and Engaging Speed of Cylinder

Fig. 20 : Adjustment Screw

4.3 Manual Adjustments To reduce the lifting height of the slip, regulate the adjustment screw. When you unscrew the adjustment screw, the lifting distance is larger.

4.3.1 Manual Lifting in Case of an Emergency

If the Power Slip PSH 150 can not be lifted by hydraulic oil, use the retaining link to lift up the Power Slip manually, ( operated with a loop lever ). Open the Hydraulic Line before ! Use Eye Protection !!

Fig. 21 : Lift Up the Power Slip Manually

Lift up

Throttle 1

Throttle 2


19

Fig. 22 : Lift Up

Fig. 23 : Lift Down

5 Lubrication

Per Week : Lubricate all movable pins with grease Per Month : Function: Manual Lifting in Case of an Emergency (Notice: should be

removed all fittings and couplings) Per ½ Year : Lubrication as above and visual inspection of hydraulic cylinder

and hydraulic hoses

Lift down


20

Lubrication points for moveable pins:

Fig. 24 : Lubrication points

Grease point 3

Grease point 4

Grease point 2

Grease point 1

Grease point 5


21

6 Inspections

6.1 Routine – Daily Field Inspection Visual Field Inspection of the Power Slip PSH 150 in an operating condition should be made by the crew or the sup visor on a regular daily basis. 6.2 Semi - Annual Field Inspection

A through on the Job shutdown Inspection should be made on a periodic basis typically at 6 months intervals, or special circumstances may require. It is advisable, that after Field Inspection should be made a record, stating the extent of testing and testing results. 6.3 Inspection

A thorough inspection should be carried out periodically (every 3 months) or special circumstances may require. At the beginning of inspection, disconnect the hydraulic system and remove all components (dirt, paint, lubricating oil, scale, etc.) from surface by a suitable method. After a field inspection, it is advisable to record the extent of testing and testing results. If cracks, excessive wear etc. is recognised, contact Blohm + Voss Oil Tools or an authorised service company.

6.4 Inspection of Hydraulic System

Check for leakage every day. Should internal or external leakage reach an unacceptable high level, contact Blohm + Voss Oil Tools or an authorised service company. 6.5 Dismantling Inspection

- Generally, when the equipment returns to base, warehouse, etc. carry out the PSH 150 inspection, immediately. Furthermore, control it prior to its being sent on the next job.

- The PSH 150 should be dismantled and inspected in a suitably equipped facility for

excessive wear, cracks, flaws or deformations. - Corrections should be made in accordance with recommendations, which can be

obtained from Blohm + Voss Oil Tools. - When need is shown in a field inspection, dismantle the PSH 150 and arrange an

inspection in a suitably equipped facility. - Springs should be carefully visually inspected for excessive wear and obvious weakness.


22

INSPECTION

CHECK LIST

FRONT PAGE TYPE OF EQUIPMENT ________________________________________ ________________________________________ PARTNUMBER ________________________________________ SUPERVISOR ________________________________________ DATE OF INSPECTION ________________________________________ INSPECTION CATEGORY ________________________________________ PLACE OF INSPECTION _____________________________________________


23

INSPECTION – CHECK LISTS Check List daily (During operation - PSH is placed in Master Bushing, Quick lock pin is locked)

GENERAL

DESCRIPTION CHECKED MONOGRAM

1 Complete front page of check list for the records OK

2 Check for correct size of slip fastening link and slips OK

3 Check correct function of slip fastening link with slips OK

Remarks

CHECK FOR LOOSE ITEMS, ESPECIALLY FOR:


1 Hinges and bolts for the slips, cover and slip fastening link OK

2 Shackle for the slips and springs OK

3 Protection plate two-sided (Pos. 22, Page 28/29/31) OK

Remarks

CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR:


1 Hinge and pins of the PSH OK

2 Slip fastening link of the slips OK

3 Shackle for the slips OK

4 Spring for the slips OK

Remarks


24

HYDRAULIC


1 Check for loose fittings, hose, valves OK

2 Check condition of hydraulic couplings and connection hoses

OK

Remarks

REMARKS SUPERVISOR DATE


25

Check List Semi annual

GENERAL


1 Complete front page of check list for the records OK

2 Check for correct size of slip fastening link and slips OK

3 Check correct function Device:

1. Hydraulic operated: Slip down Slip up Feedback „Slip down“ Feedback „Slip up“ 2. Manual operated: Slip down Slip up 3. Quick Locking Pin Assembly: lock and unlock

OK

4 Check completeness and condition of warning plates and labels

OK

5 Clean tool thoroughly OK

Remarks

CHECK FOR LOOSE ITEMS, ESPECIALLY FOR:


1 Hinges and bolts for the slips, cover and slip fastening link OK

2 Shackle for the slips and springs OK


4 Bolts for the cylinder OK

5 Bolts for the retaining link OK

6 Quick lock pin assembly OK

Remarks


26

CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR:


1 Hinge and pins of the PSH OK

2 Slip fastening link of the slips OK

3 Shackle for the slips OK

4 Spring for the slips OK

5 Bolts for the cylinder OK

6 Bolts for the retaining link OK

7 Quick lock pin assembly OK


Remarks

Hydraulic


1 Check for loose fittings, hose, valve OK

2 Check condition of hydraulic couplings and connection hoses

OK

3 Cover of hydraulic valve OK

Remarks

REMARKS


27

SUPERVISOR DATE

7 Maintenance and Repair

A regular preventive maintenance program should be established for all Power Slips. Written maintenance procedures should be given to the crew or maintenance personnel. Care should be taken, that instruction plates and warning labels are not missing, damaged or illegible.

WARNING: All warning plates and labels attached to the equipment must observed. If any safety elements (like safety ropes, safety sheets, plates or washers) were disassembled due to maintenance / repair, do NOT re-use them. Always replace them with new safety elements.


28

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

17

19

20

21

22

23

24

25

26 27

28 2934

13

6

secured by wire

securedby wire

Adjustment screw

30

31 3233

35

10

8 Principle Drawings and Part List for Power Slip PSH 150

8.1 PS Assembly without Feedback, Exploded View, P/N 88210-H

Fig. 25 : Power Slip Assembly without Feedback

Fig. 26 : Power Slip Assembly without Feedback, Exploded View


29

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

3

6

7

8

14

15

17

18

20

21

25

541

1316

582

A A

Section A-A

ø19"

Adjustment Screwto limit

the lifting distanceof the Slip

17

1

2

4

5

9

10

11

12

13

16

19

22

23

24

2726

28

29

8.2 PS Assembly without Feedback, P/N 88210-H

Fig. 27 : Power Slip, Assembly Isometric

Fig. 28 : Power Slip Assembly without Feedback


30

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

PSH 150 HYDRAULIC OPERATED WITHOUT FEEDBACK PN: 88210-H Part list Pos. Quantity Part no. Description

1 1 88260 Base Plate for PSH 150 hydraulic

2 1 88266 Jib for PSH 150 hydraulic

3 1 88205-1 Hinge Link for PSH 150 hydraulic

4 1 88206 Retaining Link

5 1 88212-1 Pin 1

6 1 88212-2 Pin 2

7 1 88212-5 Pin 5

8 1 88212-4 Pin 4

9 1 88213 Pin

10 2 88218 Cotter Pin

11 5 88214 Locking Plate

12 10 612673 Screw

13 14 645683 Washer

14 1 88221 Screw

15 1 612690 Nut

16 1 88208 Adapter for B+V Slips “short version”

1 88208-A Adapter for Access Slips “long version”

17 1 88220 Pin Assembly

18 1 621430-1 Nut

19 4 88240 Quick Lock Pin Assembly

20 1 88223-1 Manufacture Plate

21 1 88229-H Hydraulic Assembly (Hydraulic Cylinder is illustrated)

22 2 88224 Protection Plate Assembly

23 4 88224-5 Pin

24 12 88224-6 Bushing

25 4 88230 Nut

26 12 613722 WASHER WITH TAP 27 12 735852 Screw

28 6 88201-2 Shackle

29 2 88209 Spring

30 1 88265 Protection Cover for Hydraulic Block

31 4 725135 Screw

32 2 88264 Holding Angle Plate

33 4 613783 Washer with Tap

34 4 755313 Cylinder Screw

35 1 88262 Bolt for Hydraulic Cylinder


31

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

8.3 PS Assembly with Feedback, Exploded View, P/N 88210-H-F

1

2

3

4

8

67

5

10

10

11

11

11

11

11

12

1 2

12

39

39

39

14

1 5

16

17

17

18

19

20

21

22

9

23

24

25

26

27

28

29

30

3332

32

33

33

34

3 5

36

37

38

3 9

39 41

42

43

44

45

46

4 7

6

31

3 1

Ad ju st ment Screw

13

33

31

1212

39

13

secured by wire

secured by wire

40Optional:Pos.16 or Pos.40

Fig. 29 : Power Slip Assembly with Feedback, Exploded View


32

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

PSH 150 HYDRAULIC OPERATED WITH FEEDBACK PN: 88210-H-F Part list Pos. Quantity Part no. Description

1 1 88260-F Base Plate for PSH 150 hydraulic

2 1 88266-F Jib for PSH 150 hydraulic

3 1 88205-1 Hinge Link for PSH 150 hydraulic

4 1 88206 Retaining Link

5 1 88212-1 Pin 1

6 1 88212-2 Pin 2

7 1 88212-5 Pin 5

8 1 88212-4 Pin 4

9 1 88213 Pin

10 2 88218 Cotter Pin

11 5 88214 Locking Plate

12 10 645028 Screw

13 6 645683 Washer

14 1 88221 Screw

15 1 612690 Nut

16 1 88208 Slip Fastening Link

17 1 88220 Pin Assembly

18 1 621430-1 Nut

19 4 88240 Quick Lock Pin Assembly

20 1 88282-2 Manufacture Plate

21 1 88229-H-F Hydraulic Assembly (Hydraulic Cylinder is illustrated)

22 2 88224 Protection Plate Assembly

23 4 88224-5 Pin

24 12 88224-6 Bushing

25 4 735846-E Nut

26 12 613722-E WASHER WITH TAP 27 12 735852-E Screw

28 6 88201-2 Shackle

29 2 88209 Spring

30 1 88265 Protection Cover for Hydraulic Block

31 4 725135 Screw

32 2 88264 Holding Angle Plate


34 4 755328 Cylinder Screw

35 1 88262 Bolt for Hydraulic Cylinder

36 1 88236 Valve Plate

37 1 88237 Valve Angle

38 1 88238 Switching Ramp


40 1 88208-A Slip Fastening Link


33

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

41 4 775092-1 Screw

42 2 88235 Screw

43 2 645671 Screw

44 1 613715 Screw

45 2 88234 Cylinder Head Screw

46 4 88233 Cylinder Head Screw

47 1 735846 Nut


34

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

8.4 PS Hydraulic Assembly without Feedback, Exploded View, P/N 88229-H

Fig. 30 : Power Slip, Hydraulic Assembly , Exploded View

1 2 3 4 5 2 3 4 5

4

4

5

5

5

6

8

7

9

10

11 11

12 1313

1415

16

16

16

17

18

19

20

21

22

23

2425

268828427


35

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

P

T

T

P

B

PSH-150 hydraulic operatedwithout Feedback

A

A B

down up

Rotary Slip

Hydraulic block

Po

we

rS

up

ply

B

A

25

26

2448941115

1413121311

21

19

11

22

2

3

4

6 75 5

11

21 21

5 5

17

18

18

27

23

8.5 PS Hydraulic Assembly without Feedback, P/N 88229-H

Fig. 31 : Power Slip without Feedback, Hydraulic Assembly

Notice: Position 16 and 20 are not illustrated in the hydraulic schematic


36

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

P

T

T

P

Hydraulic Block

B

PSH-150 hydraulic operatedwith Feedback Signal

A

A B

Po

wer

Su

pply

B

A

down up

Rotary Slip

13

141215

9

10

19

10

2

4

30

3

17

18

18

22

7

a

R P

ac t uat ed w hen Sl ipare ra i sed

C

Fee

db

ack

a

R P

ac tua ted w hen S li pare se t

2 3 .2

332 3. 6

2 3. 3

1616 20

23 . 4

3

3

23 .7

15 2 3. 1 12

24

9 821

23 .1

2 3. 5

1131

3332

9

30

9

14

13

25

27

27

30

28

28

31

34

34

2631

9

Notice: Position 5 and 6 are not illustrated in the hydraulic schematic

8.6 PS Hydraulic Assembly with Feedback, P/N 88229-H-F Fig. 32 : Power Slip with Feedback, Hydraulic Assembly


37

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

HYDRAULIC ASSEMBLY WITHOUT FEEDBACK PN: 88229-H Part list Pos. Quantity Part no. Description

1 1 615915 Hydraulic Cylinder

2 2 755365 Banjo Coupling 3/8”

3 2 755372 Standpipe Reducer

4 6 612951 Hose Connection

5 8 612955 Hose Fitting

6 0,5m 612956 Hydraulic Hose for Line B

7 1m 612956 Hydraulic Hose for Line A

8 0,5m 612956 Hydraulic Hose

9 0,5m 755355 Protection Hydraulic Hose

10 2 612953 Hose Connection 45 degree

11 5 645096 L-Adapter

12 0,1m 645093 Hydraulic Pipe

13 2 756325 Sealing for cutting ring

14 2 612664-2 Nut

15 2 88226 Weldable Bulkhead Coupling

16 17 612929 Blind Screw

17 2 611024 Excess Pressure Valve

18 2 645097 Check Valve

19 2 645090 Throttle

20 2 645092 Blind Screw 3/8”

21 3 612944 Straight Connection ¼”

22 1 613946 Straight Connection

23 2 645094 Blind Screw ½”

24 2 613943 Straight Male Stud Coupling

25 1 612937-1 Coupling Female

26 1 612936-1 COUPLING MALE 27 1 88263 Distribution Block


38

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

HYDRAULIC ASSEMBLY WITH FEEDBACK PN: 88229-H-F Part list Pos. Quantity Part no. Description

1 1 615915 Hydraulic Cylinder



4 2 755372 Standpipe Reducer

5 21 612929 Blind Screw G ¼”

6 2 645092 Blind Screw G 3/8”

7 2 645094 Blind Screw G ½”

8 2 613049 Nut

9 5 645096 L-Adapter


11 1 645095 L-Adapter


13 2 1038-F Quick connect coupling female

14 2 1038-M Quick connect coupling male

15 3 88226 Weldable bulkhead connection

16 2 775088 2-Way-Valve

17 2 611024 Excess Pressure Valve


19 2 645090 Throttle


21 94 mm 645093 Hydraulic Pipe

22 1 88263 Distribution Block

23 1 88229-40 Hydraulic Hose Assembly

23.1 3 88229-14 Hose Assembly 5

23.2 1 88229-15 Hose Assembly 6

23.3 1 88229-16 Hose Assembly 7

23.4 1 88229-17 HOSE ASSEMBLY 8 23.5 1 88229-18 Hose Assembly 9

23.6 1 88229-19 Hose Assembly 10

23.7 1 88229-20 Hose Assembly 11

24 1 1014-M Quick connect coupling male

25 1 1014-F Quick connect coupling female

26 1 645117 Direct Pipe Fittimg

27 2 755373 Straight Male Stud Coupling

28 2 755364 Swivel Reducer

29 2 613049-1 Cutting Ring

30 3 612944 Straight connection

31 3 612945 Swivel reducer

32 1 755738 Equal elbow

33 1 755737 Equal tees

34 2 645116 Direct Pipe Fitting


39

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

8.7 Quick Lock Pin Assembly, P/N 88240

Fig. 33 : Power Slip, Quick Lock Pin Assembly

Fig. 34 : Power Slip, Quick Lock Pin Assembly, Exploded View

1

2

4

7

9

8

5

6

10

3


40

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

QUICK LOCK PIN ASSEMBLY PN: 88240 Part list Pos. Quantity Part no. Description

1 1 88240-1 Excenter

2 1 88240-2 Screw

3 1 88240-3 Pin

4 1 88240-4 Split Pin

5 1 88240-5 Pivot

6 1 88240-6 Clamp

7 1 88240-7 Washer

8 1 88240-8 Rubber Washer

9 1 88240-9 Bushing

10 1 88240-10 Nut


41

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

8.8 Protection Plate Assembly, P/N 88224

Fig. 35 : Power Slip, Protection Plate Assembly

1

2

3


42

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

PROTECTION PLATE ASSEMBLY PN: 88224 Part list Pos. Quantity Part no. Description

1 2 88224-1 Cover

2 2 88224-2 Segment 1

3 2 88224-3 Segment 2


43

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

9 Spare Parts List (2 Years operation)

9.1 88210-H-RSP for PSH 150-Hydraulic without Feedback Quantity Part no. Description

1 88212-1 Pin Type 1

2 88212-2 Pin Type 2

1 88212-5 Pin Type 5

1 88212-4 Pin Type 4

1 88213 Pin

1 88218 Cotter Pin

1 88208 Adapter for B+V Slip

1 88208-A Adapter Long Version "A" for Access-Slips

1 88220 Pin and Washer

1 621430-1 Nut

4 88240 Quick Lock Pin assembly

2 88209 Spring

1 611024 Excess pressure valve

1 645090 Throttle

1 1038-F Quick connect coupling 3/8 female

1 1038-M Quick connect coupling 3/8 male


44

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

9.2 88210-H-F-RSP for PSH 150-Hydraulic with Feedback Quantity Part no. Description

1 88212-1 Pin Type 1

2 88212-2 Pin Type 2

1 88212-5 Pin Type 5

1 88212-4 Pin Type 4

1 88213 Pin

1 88218 Cotter Pin

1 88208 Adapter for B+V Slip

1 88208-A Adapter Long Version "A" for Access-Slips

1 88220 Pin and Washer

1 621430-1 Nut

4 88240 Quick Lock Pin assembly

2 88209 Spring

1 611024 Excess pressure valve

1 645090 Throttle

1 775088 Directional poppet valve






45

Oil Tool Division

Rep

air

Gm

bH

Blohm+Voss

10 Address List

Blohm+Voss Oil Tools Hermann-Blohm-Straße 2 D-20457 Hamburg

Germany

Phone: ++49-40-3119-1826/1162 Fax: ++49-40-3119-8194 E-Mail: [email protected] Internet: www.blohmvoss-oiltools.com Gray EOT, Inc.

7670 Woodway, Suite 266 Houston, Texas 77063 United States of America Phone: +1-713-95 20 266 Fax: +1-713-95 22 807 Email: [email protected] Internet: www.blohmvoss-oiltools.com Premier Sea & Land Pte Ltd

1, Scotts Road #19-12 Shaw Center Singapore 228208 Republic of Singapore Phone: +65-6734-71 77 Fax: +65-6734-91 15 Email: [email protected]

Documents

Blohm + Voss PSH 150 Power SlipV... · Blohm + Voss PSH 150 Power Slip for 2 3/8” – 7 5/8” Rotary Standard Slips Hydraulic Operated P/N 88210-H Hydraulic Operated with Feedback