4.22 EQUIPMENTWISE TECHNICAL DATA TO BE

FURNISHED BY THE TENDERER

4.22.1

SCOPETenderer shall furnish the equipmentwise technical data as per the following:

A)WATER CHILLING UNITS

a)Make

a) Model

c)Compressor type

d)No. of compressors

e)Refrigerant

f)Capacity at the specified condition

g)Quantity of chilled water out(C

in(C

h)Quantity of condenser water out(C

in(C

i)Input KW at

100% load (KW)-

75% load (KW)-

50% load (KW)-

25% load (KW)-

10% load (KW)-

j)Drive motor rating

k)Starter type & no.

l)Circuit breakers -No.

Type

Amp.

m)Incoming breaker size required Amp.

n)Physical dimension of the unit

o)Weight

Dead

Operating

p)Noise (DBA) at a distance of 3M

Chiller

a) Water passes (No.)

b) Refrigerant circuits (No.)

c) Shell dia & shell length

d) Water side pressure drop (Kpa)

e) Fouling factor

f) List of accessories including operational andSafety interlocks

g) Operating weight Condenser

a) Type

b) Shell dia & length

c) No. of tubes & dia of each tube

d) No. of fins per inch

e) Fin material & thickness f) Water pressure drop g) Fowling factor

h) List of accessories including operation andsafety interlock

i) Operating weight

B)CHILLED & CONDENSER WATER PUMPS (Performance Curve to be given)

a)Pump discharge (CMH)

b)Head (Kpa)

c)NPSH (Kpa)

d)BKW

e)Motor rating

d)Starter type

e)Motor enclosure (IP Rating)

f)Make/Model

g)Size

h)Operating weight

i)Pump RPM

C)AIR HANDLING UNITS

a)Make/Model/Type

b)Air quantity (CMH)

c)Total static pressure (MMWC)

d)Speed (RPM)

e)BKW

f)Motor rating & Make

g)StarterType

Make

h)Motor enclosure (IP)

i)Fan outlet velocity (M/S)

j)Fan make and model

k)Coil Row/Deep

l)CoilFace Area (SQM)

Tube dia & tube thickness (MM)

No. of tubes

No. of Fins/inch

Fin material/thickness

m)Air entering temperature (C

Air leaving temperature (C

n)Water quantity (m3/hr) -

o)Water temperatureIn (C

Out (C

p)Pressure drop (mmWC)

q)Pre-filter material

r)Make/size

s)FilterFace area (SQMM)

Air velocity (M/S)

t)Pressure drop

Clean condition (mmWC)

Dirty condition (mmWC)

u)Filtering efficiency

v)Fine filter material/Make/Size

w)FilterFace area (SQM)

Air velocity (M/S)

x)Pressure drop

Clean condition (mmWC)

Dirty condition (mmWC)

D)FANS

a)Make/Model

b)Type/Discharge

c)Speed (RPM)

d)Air Quantity (CMH)

e)Static Pressure (MMWC)

f)Power Consumption (KW)

g)Motor Rating

h)Starter type

i)Motor enclosure (IP)

E)FAN COIL UNITS

a)Make/Model -

b)Type/Discharge

c)Air quantity

d)Fan pressure

e)Fan speed

f)Noise level at 1 mtr. distance

F)COOLING TOWER

a)Make/Model -

b)Size

c)Type

d)Fan speed

e)Air quantity

f)Static pressure

g)BKW

h)Motor rating

i)Starter type

j)Motor enclosure

k)Noise level (DB) at distance of 1 mtr.

l)Operating weight

m)Range

n)Approach

o)Selection at what wet bulb temp.

p)Tower construction & fill material

q)No. of cells

r)List of accessories included

G)TUBE AXIAL FAN

a)Make -

b)Type

c)Capacity (CMH)

d)Fan model

e)Input KW

f)Fan diameter

g)Fan coverage

h)Fan speed

i)Suitable for 300C for 2 hrs. (yes/no)

j)Sound level at a distance of 1 mtr.

k)Weight

l)Dimension

m)Type of drive

n)Accessories included

H)VRV SYSTEM

Outdoor Unitsa) Capacity (HP/TR)-b) Make -

c) Type of Compressor-

d) No. of Compressors-e) Total power consumption-Indoor Units

a) Make-b) Type-c) Capacity (CFM/TR)-Make of Refrigerant Pipes -

I)SPLIT AIR CONDITIONER

a)Make-

b)Capacity-

c)Model -

J)DUCTABLE AIR CONDITIONERS

a)Make-

b)Capacity-

c)Model -

K)Write up on Central controller & its Accessories

-----x-----PAGE P-4.22, 5 out of 5