Upload
dangminh
View
220
Download
4
Embed Size (px)
Citation preview
CFD-based plant development
Key information
BIOS BIOENERGIESYSTEME GmbH
T[K]
2200
300
600
1600
1800
2000
1700
1000
1100
1200
1300
1400
1500
900
800
700
500
400
1900
2100
dDepo [mm]
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 1
Key information and references
concerning the CFD simulation activities of
BIOS BIOENERGIESYSTEME GmbH
What is CFD?
CFD (Computational Fluid Dynamics) is the spatially (and temporally) resolved simulation of flow and
heat transfer processes. Flows may be laminar or turbulent; they may be reactive or occur in a
multiphase system. CFD simulations thus constitute an excellent tool for process analysis as well for
the design and optimisation of plants.
Basic principles and general conditions
CFD simulations are applied to solve problems in various areas, for example in the automobile and
aircraft industries, the biomedical industry, electronics cooling, in chemical engineering, for turbo
machinery, in combustion processes, in heat and power generation, and for heating and cooling pipes.
In the field of energy technology CFD is being increasingly used for the optimisation of gas and oil
burners as well as for pulverised coal furnaces.
CFD modelling of biomass combustion and gasification plants is especially difficult due to the
complexity of the processes involved in the thermal conversion of solid biomass, as well as due to the
turbulent reactive flow in the combustion chamber or the gasification reactor, respectively. BIOS, in co-
operation with researchers of Graz University of Technology, Institute for Process and Particle
Engineering, has successfully developed a CFD model especially designed for the development and
optimisation of biomass grate furnaces, boilers and fixed bed gasification plants. The CFD model
consists of an in-house developed empirical grate combustion model complemented with modified and
lab-scale tested CFD sub-models (FLUENT code) for the turbulent reactive flue gas flow in the
combustion or gasification reactor. The applicability of the CFD model, as well as the reliability of
simulation results were tested at pilot-scale and industrial-scale furnaces.
The long-standing continuous co-operation of BIOS with various research institutions, such as the
Institute for Process and Particle Engineering of Graz University of Technology and the Austrian
biomass competence centre ‘BIOENERGY 2020+’ ensures that the employed models are kept at the
forefront of scientific developments.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 2
Goals of CFD-based plant development
The goal of a CFD-aided plant development is an efficient technological development and conception
of plants aided by a spatially and temporarily resolved simulation and visualisation of the processes in
biomass combustion and gasification plants. The objectives in detail are:
For combustion plants:
Efficient mixing of unburned flue gas with re-circulated flue gas and efficient air staging
improved CO burnout, NOx reduction
Improved mixing of unburned flue gas with secondary air efficient CO burnout, reduction of
furnace and boiler volumes
Improved utilisation of furnace and boiler geometries efficient CO burnout, reduction of
furnace and boiler volumes
Reduction of local velocity and temperature peaks in order to reduce material erosion and ash
deposit formation
Sensitivity analyses as a basis for the optimisation of plant control
(e.g. influence of load, water content and air staging)
For gasification plants:
Optimisation of the gasification agent and the reactor geometry in order to achieve an as
complete as possible gasification and low tar contents in the product gas
Optimisation of flow and temperature distribution in gas cleaning units
Assessment and optimisation of the combustion of product gas
Advantages of CFD-based plant design
CFD-based plant design brings the following advantages:
Reduced emissions
Increased plant efficiency
Smaller plant design
Increased fuel flexibility
Reduced material wear
Increased plant availabilities and operating hours
Reduced consumption of operating agents for SNCR units
Reduction of development times and costs for test runs
Increased reliability of plant development
Improved basic understanding of the processes taking place in combustion or gasification
reactors
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 3
Working fields of BIOS BIOENERGIESYSTEME GmbH
BIOS BIOENERGIESYSTEME GmbH is an engineering company highly experienced in the field of
CFD simulations of plants for thermo-chemical biomass conversion and offers the following simulation
services:
CFD-based development and optimisation of plants, CFD-based monitoring (test runs plus
accompanying CFD simulations) of biomass combustion plants and boilers in the small (furnaces fired
with pellets, wood chips and wood logs, as well as stoves), medium and large scale:
Design and optimisation of
o fixed bed and grate furnaces
o wood log fired boilers
o wood log fired stoves
o pellet stoves
o pulverised fuel furnaces
Design and optimisation of boiler geometries (including convective sections: resolved
geometry of boiler tubes for small-scale plants and using a heat exchanger model for medium
and large-scale plants)
Design and optimisation of nozzles for the injection of re-circulated flue gas
Design and optimisation of nozzles for the injection of secondary/tertiary air
Optimisation of air staging
Optimisation of pressure losses in order to support fan design
Reduction of local temperature peaks by cooling the combustion chamber and optimisation of
operating conditions
Prediction of zones prone to erosion and ash deposit formation
Modelling of the formation of ash deposits and fine particulates in biomass fired boilers
Calculation of heat transfer in and the influence of deposits (slagging and fouling) on biomass
fired boilers
Calculation of residence times using different methods (Lagrange and Euler) for the optimised
design of primary combustion zones (NOx reduction via primary measures) and secondary
combustion zones (flue gas burnout), SNCR and additive injection systems
High temperature equilibrium calculations for the evaluation of ash melting behaviour
Reduction of emissions (carbon monoxide, nitrogen oxides, fine particulate emissions)
Calculation of the precipitation rates of fly ash particles and ash vapours in various plant
zones
Investigation/optimisation of the operating conditions of furnaces and boilers with regard to
efficiency, plant availability, partial load operation and fuel flexibility
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 4
Further CFD applications:
Application of furnace models to waste incineration plants
Simulation of biomass gasification plants
Simulation of rotary cement kilns
Calculation of heat and pressure losses in pipe networks (e.g. district heating)
Simulation of cyclones (particle precipitation, erosion tendencies)
Simulation of filters and particle separators
Air conditioning simulations in boiler houses and industrial plants
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 5
More detailed information on CFD simulations
Design and optimisation of nozzles for the injection of secondary air and re-
circulated flue gas
The design of the secondary air and flue gas nozzles is a key factor in meeting the following
requirements:
High turbulent mixing and homogenisation of the flow across the flue gas channel.
Minimisation of furnace volume (investment costs).
Reduction of excess air and flue gas recirculation ratio (efficiency, operation costs).
Reduction of CO and NOx emissions.
Reduction of temperature peaks (fouling and slagging) and flue gas velocity peaks (material
stress and erosion).
An example of a furnace geometry optimised by CFD analysis is shown in the figure below. A
significant reduction of CO emissions and temperature peaks was achieved by the appropriate
arrangement of the secondary air nozzles, resulting in optimised mixing conditions.
Biomass grate furnace equipped with a
horizontally moving grate
CO concentrations [ppmv] (above) and
temperature distribution [°C] (below) in different
cross-sections near secondary air injection nozzle
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 6
Design of the geometry of the combustion chamber
The design of the geometry of the combustion chamber is of great importance in order to fulfil the
requirements already stated for the design of the secondary air and flue gas injection nozzles.
Below, exemplary figures of a Low-NOx biomass grate furnace appropriate for a broad fuel assortment
(waste wood, wood chips, bark) are shown. This type of furnace was realised as a pilot-scale plant
and subsequently also as a large-scale plant. The combination of vertical barriers and a staged
secondary air injection leads to a highly turbulent mixing, a homogeneous flue gas distribution and a
good utilisation of the secondary combustion zone. Besides a significantly reduced and simplified
furnace volume, the following advantages could be achieved:
Strong reduction of CO
emissions
CO profiles [ppmv] in the symmetry plane of the furnace
Lowering of temperature
peaks (fouling & slagging)
Temperature profiles [°C] in a horizontal cross-section at the level of the vertical barriers and the
secondary air nozzles
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 7
Lowering of flue gas velocity
peaks (erosion & material
stress)
Profiles of flue gas velocity [m/s] in a horizontal cross-section at the level of the vertical barriers and
the secondary air nozzles
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 8
Optimised design of wood log fired stoves
The basic grate combustion model, which was developed to describe the release of the flue gas
components during biomass combustion on the grate in order to achieve boundary conditions for the
CFD simulation of turbulent reactive flow in the combustion chamber, was modified for wood log fired
stoves, wood log furnaces and wood log fired boilers operated in discontinuous batch mode. This
modified model is used to calculate time-dependent profiles of wood log combustion by a
transformation of the release profiles along the grate determined with the basic grate combustion
model. Using these time-dependent profiles, the composition of a virtual fuel consisting of the fuel
components C, H, N, O and water vapour converted during solid biomass combustion, can be
determined at any point in time. Furthermore, a mass balance and the amount and composition of flue
gas released can be calculated at any point in time during batch operation.
In order to prevent the distortion of CFD simulations by the heat storage of the stove when defining
virtual steady-state operating cases, it is necessary to determine the time-dependent profile of the heat
fluxes over the stove surface based on test runs. By balancing energy, two virtual steady-state
operating cases can be identified, which are characterised by the heat storage of the stove, which is
zero.
The following processes can be analysed with the in-house developed CFD model for wood log fired
stoves:
Flow of combustion air and flue gas in the stove and flow of convection air in the double jacket
of the stove
Gas phase combustion in the stove
Heat transfer (conduction, convection, and radiation) between gas phase, stove materials
(stove lining, metal sheets and glass sheets) and surroundings
This enables analysis of:
Velocities and temperatures of combustion air, convection air and flue gas
Path lines of air and flue gas
Concentrations of O2 and CO in the flue gas
Material and surface temperatures of stove lining, metal sheets and glass sheets (see figure
below)
Heat transfer and efficiency
Pressure losses over different plant zones
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 9
Temperature profiles at the outer surface of a wood log fired stove [°C]; 3D view of the front side (left)
and backside (right) of the stove
In the figure below the development of a new stove is demonstrated by means of the CO
concentrations. In the basic variant the emissions are rather high due to a bypass flow in the
redirection baffle of the post combustion chamber. Furthermore, the post-combustion chamber was
not insulated. In the pre-optimised variant (before the realisation as testing plant) first improvements
could be achieved by a closure of the bypass flow and an insulation of the post combustion chamber.
By these measures, the temperature in the post-combustion chamber was elevated and the CO
burnout considerably improved. A further improvement could be achieved by the optimised variant
which was realised as testing plant. Here, additional tertiary air nozzles have been installed in the rear
part of the combustion chamber, which lead to an improved flue gas burnout already in the combustion
chamber. Moreover, the CO emissions are a leading parameter for the burnout quality of the flue gas
and can be used as an important indicator concerning organic fine particle emissions from incomplete
combustion. Besides the considerably reduced CO emissions also the organic fine particle emissions
could be reduced. Finally, the excess air could be reduced, leading to a higher plant efficiency.
Basic geometry
(tot = 2.3)
Optimised geometry
(tot = 2.0)
window
entrance of
flushing air
flue gas
exit
combustion
chamber
post-combustion
chamber
tertiary air
nozzles
wood logs
redirection
baffle
transition
5000
4750
4500
4250
4000
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
1250
1000
750
500
250
0
Iso-surfaces of CO concentrations [ppmv w.b.] in the flue gas in the vertical symmetry plane of a stove
Modifications: closure of opening in the redirection baffle; additional tertiary air nozzles; larger
transition to the chimney and insulation of the post-combustion chamber
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 10
Optimised design of wood log furnaces
The basic grate combustion model, which was developed to describe the release of the flue gas
components during biomass combustion on the grate in order to achieve boundary conditions for the
CFD simulation of turbulent reactive flow in the combustion chamber, was modified for wood log fired
stoves, wood log furnaces and wood log fired boilers operated in discontinuous batch mode (for further
information see section “Optimised design of wood log furnaces”). Here, virtual steady-state operating
cases are balanced with the empirical model for which CFD simulations of flow, gas phase combustion
and heat transfer can be performed for any point in time during batch operation.
The CFD simulations enable an analysis of:
Quality of penetration of the primary combustion zone (space filled with log wood) with primary
air
Utilisation of the secondary combustion zone, mixing of flue gas with secondary air and CO
burnout
Velocity and temperature peaks for the best possible reduction of material erosion and ash
deposit formation
Heat transfer in the primary and secondary combustion zones of the furnace as well as in the
boiler tubes as a basis for the optimisation of thermal efficiency
Pressure losses over different plant zones
Results of a CFD analysis of a wood log furnace are shown in the following figure. The diagram on the
left shows path lines of the primary air coloured by gas temperature. The path lines allow the
penetration of the space filled with log wood to be analysed and optimised in order to achieve good
and even combustion of the wood logs and to avoid bridging. The diagrams on the right show
calculated CO concentrations in different cross-sections of the secondary combustion zone, which
serve as a basis to analyse and optimise the mixing of flue gas with secondary air and the utilisation of
the secondary combustion zone.
Path lines of primary air in the primary combustion zone coloured by gas temperature [°C] (left); CO
concentrations [ppmv] in a horizontal cross-section (top right) and in a vertical cross-section (bottom
right) of the secondary combustion zone
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 11
Simulation of pulverised biomass furnaces / entrained flow reactors
Models have been developed for the combustion of thermally thin and thick biomass particles in order
to utilise CFD for the design of pulverised combustion and gasification units. The models for thermally
thick biomass particles take the intra-particle mass and heat transfer into account and thus enable a
more accurate prediction (compared to available commercial CFD particle models) of the combustion
process of the solid biomass particle and particle temperature. The model for entrained flow
conversion was successfully tested by a comparison with measurements for a pulverised biomass
flame and successfully applied to the simulation of a pulverised wood furnace. This model allows the
qualitative description of particle combustion along particle trajectories and thus provides qualitative
information about the flow and combustion processes in the furnace, making it ideal for the
development and optimisation of pulverised biomass furnaces.
The simulated CO concentrations in the vertical symmetry plane of the basic design (left) and the
optimised design (right) are shown in the following figure. The results show that a considerable
improvement of CO burnout in the furnace can be achieved by modifying the design of the nozzles for
the supply of secondary air and re-circulated flue gas as well as the operating conditions.
Basic design Optimised design
Fuel supply with carrying airFlue gas re-circulation nozzles
Secondary
air nozzles
1 nozzle pair
closed
1 nozzle pair
closed
CO concentrations [ppmv] in the vertical symmetry plane of a pulverised wood furnace
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 12
Investigation of furnace cooling systems
As mentioned before, moderate and well controlled flue gas temperatures in the furnace are important
in order to prevent slagging and deposit formation. Additional measures like cooled walls or tubes are
recommended especially for dry fuels (waste wood) and biomass fuels with a high content of alkali
metals (straw).
The figure below shows the temperature distribution in a biomass grate furnace for waste wood
combustion with path lines of re-circulated flue gas injected by the lower nozzle row, indicating high
turbulent mixing and increased flue gas temperatures. The highest flue gas temperatures near the wall
are expected in the primary combustion zone and the regions around the flue gas and secondary air
injection nozzles. Cooled furnace walls are recommended for this region in order to lower temperature
peaks and to prevent slagging.
Temperature profiles [°C] in different horizontal cross-sections at the level of re-circulated flue gas and
secondary air injection; the furnace wall section between and around the nozzles is cooled
Explanations: SA…secondary air nozzles; FGR…flue gas re-circulation nozzles
SA
FGR
FGR
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 13
CFD simulation of boilers including the convective section
CFD simulation also proved to be a powerful tool for the design of biomass boilers. Optimisation of
flow results in an improved utilisation of the boiler volume, enhanced heat transfer and a more even
temperature distribution, thereby also reducing deposit formation.
In view of this potential, BIOS BIOENERGIESYSTEME GmbH has carried out an R&D project in order
to develop a CFD model for heat exchangers. This model allows the flue gas flow within the tube
bundles of the convective heat exchanger section to be included in the CFD optimisation process. A
detailed simulation of convective heat exchangers would be impossible in most cases, as the high
spatial resolution needed to resolve the geometry of interest could not be covered by computer
capacity.
The simulation models developed are able to predict the flue gas flow field including the pressure
losses, as well as the heat transfer within the convective part of the boiler. Furthermore, the maximum
temperatures at the flue gas side of the heat exchanger tubes are calculated, which are the crucial
factor in the process of formation of solid deposit layers. Special attention is paid to the influence of
radiative heat transfer on tube rows exposed to increased thermal radiation.
Consequently, the CFD simulation gives better and more valuable information for tube bundles in
highly inhomogeneous flow fields, e.g. tube bundles positioned in regions of strong flow deflections,
than conventional heat exchanger design methods based on one-dimensional assumptions. The
following advantages for the optimisation of biomass boilers can be summarised:
optimisation of flow through the heat exchanger tube bundles
decision basis for arranging the evaporator tube bundles upstream the superheater sections
identification of surfaces prone to formation of sticky ash deposit layers
optimised positioning of soot blowers to improve the functionality of the boiler cleaning system
optimisation of steam parameters to increase the efficiency of electricity production
The CFD model developed expands the capabilities of the present state-of-the-art commercial CFD
software and is currently available for the most relevant boiler types (water tube steam boilers, thermal
oil and fire tube boilers). Additionally, the model is able to simulate the flow of both primary and
secondary heat carriers. It can thus be used to optimise heat transfer and flow field for both flue gas
and water side in a fire tube boiler. Exemplary simulation results for different biomass boilers are
shown in the following.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 14
(a) Flue gas temperature distribution [K] and (b) maximum temperature [K] at the flue gas oriented
surfaces of fouled heat exchanger tube bundles in the convective section of a biomass fired steam
boiler.
The figures above show CFD results of a real plant, which was selected for validating the CFD models
developed by BIOS BIOENERGIESYSTEME GmbH. The inhomogeneous inlet flow into the
convective part of the boiler leads to a strong fluctuation of the maximum tube surface temperatures at
the first tube rows of the evaporator section. Deflections of the flue gas flow in front of the tube bundle
heat exchangers can be optimised by means of CFD simulations in order to achieve a more even
distribution of the incoming flow and a reduction of temperature peaks.
Temperature profiles [°C] in different horizontal cross sections of a thermal oil-boiler (radiative section)
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 15
Profiles of the flue gas side wall temperature [°C] of the radiative heating surfaces of a thermal oil
boiler at different stages of fouling from clean walls (left) to walls covered with a considerable layer of
fly ash deposits (right)
The figures above show simulation results of flue gas temperature profiles in the radiative section of a
thermal oil boiler as well as simulation results based on an investigation of the effective heat transfer in
the radiative section of the boiler under real operating conditions. The increased wall temperatures
due to deposit layer formation lead to a dramatic reduction of the heat transfer in the radiative boiler
section. This should be considered in boiler dimensioning and should be prevented as far as possible
by an appropriate design and by appropriate automatic cleaning facilities.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 16
Computational grid (above) and flue gas temperature profiles [°C] in the symmetry plane of a fire tube
boiler; a) simulation of the convective section using the CFD heat exchanger model; b) detailed
simulation of the convective section with spatially resolved tubes.
The figure above shows the results of a validation study of the developed CFD heat exchanger model
for fire tube boilers. A comparison of a detailed boiler simulation with a simulation using the CFD heat
exchanger model was performed for this study. The detailed simulation, used as a reference, was
carried out with spatially resolved tubes (convective section). However, this is only possible for very
small boilers. In the simulation using the CFD heat exchanger model the tubes were considered by the
model (compare figures above). The comparison shows good agreement of the simulation results for
both methods (see flue gas temperature shown). An additional comparison with experimental data of
pressure losses and heat transfer in the boiler also showed good agreement of calculated and
experimental results. The CFD heat exchanger model can thus be applied as a design tool for fire tube
boilers.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 17
Simulation of ash deposit and fine particulate formation in biomass furnaces
and boilers
It is of the utmost importance to avoid the formation of deposits in biomass furnaces and boilers. A
model accounting for deposit formation is currently under development in a R&D project. Furthermore,
the reduction of fine particulate emissions is gaining increasing importance due to continuously stricter
emission limits and an increasing market demand concerning „new“ biomass fuels with enhanced ash
contents like short rotation coppice and agricultural residues. A model accounting for deposit and fine
particulate formation is currently under development in a R&D project. At the present stage of CFD
modelling, the time-dependent formation of deposits at furnace walls and boiler walls can be predicted.
The model currently considers the impaction of fly ash particles (silicate and salt particles) depending
on their stickiness, as well as the condensation of ash forming vapours at furnace and boiler walls.
Furthermore, the formation of fine particulates (basic model) and their deposition on furnace and boiler
walls can be investigated. In addition, the erosion of the deposition layer by coarse fly ash particles
can be studied. This model is characterised by high flexibility regarding the biomass fuel used, a
detailed consideration of the ash chemistry and reasonable computing time even if applied for
engineering applications.
Calculated thickness (mm) of deposit layers in furnace and radiative boiler sections (fire tube boiler) of
a biomass grate furnace (fuel: waste wood) after 1 hour of operation
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 18
Calculated deposit mass flux (kg/m2s) of coarse fly ash particles to the walls of furnace and radiative
boiler section (fire tube boiler) of a biomass grate furnace (fuel: waste wood) after 1 hour of operation
Calculated condensation mass flux (kg/m2s) of K2SO4 to the walls of furnace and radiative boiler section (fire tube boiler) of a biomass grate furnace (fuel: waste wood) after 1 hour of operation.
The figures above exemplify the deposit build-up calculated for a waste wood fired grate furnace
including the radiative section of the fire tube boiler. The separate visualisation of the different deposit
formation mechanisms (e.g. deposit build-up by impaction of coarse fly ash particles or by
condensation of different ash forming vapours (e.g. K2SO4)) can be mentioned as a major advantage
of this deposit formation model. The simulation results agree qualitatively with observations made in
the biomass grate furnace investigated as well as in a number of other biomass fired boilers.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 19
sum of fine particles formed
0%
20%
40%
60%
80%
100%
measurement simulation
chemical composition of the
fine particles
primary
air
supply
SCZ
heat
exchanger
0%
20%
40%
60%
80%
100%
measurement simulation
Cl
S
Na
KPCZ
secondary air nozzles
14.3
13.5
12.7
11.9
11.1
10.3
9.5
8.7
7.9
7.2
6.4
5.6
4.8
4.0
3.2
2.4
1.6
0.8
0.0
14.3
13.5
12.7
11.9
11.1
10.3
9.5
8.7
7.9
7.2
6.4
5.6
4.8
4.0
3.2
2.4
1.6
0.8
0.0
1
2
Total fine particle concentrations [mg/Nm³ dry flue gas, 13% O2); (left) and chemical composition of
the fine particles (right)
Explanations: 70 kW pellet boiler; 1…first particle formation; 2…particle formation starts to dominate at
the entrance into the heat exchanger; PCZ…primary combustion zone; SCZ…secondary combustion
zone
In the figure below the simulation results concerning fine particulate formation in a 70 kW pellet boiler
are shown. In the PCZ, the flue gas temperature and the wall temperatures are too high for a direct
wall condensation or fine particle formation. The first formation was predicted at the exit of the PCZ.
Simultaneously to the fine particle formation, condensation occurs at the cooled walls. The highest
deposition mass fluxes have been calculated on the opposite side of the SCZ. In this region, mass
transfer coefficients as well as concentration gradients at the wall are high in comparison to the other
regions. In the heat exchanger, the condensation flux strongly decreases and the formation of fine
particles dominates. For the purpose of model check, the simulation results have been compared with
measurements during test runs. The predicted fine particle emissions are in good agreement with the
measurement values (simulated: 9.92 mg/Nm³; measured: 7.65 mg/Nm³). Moreover, the predicted
chemical composition of the fine particulate emissions is in good agreement with results from chemical
analyses. Concluding, the selected results of a number of validation simulations showed that already
at the present state of development the model is able to predict fine particulate formation and
emissions even at a quantitatively acceptable level. Hence, the model under development can be
already applied as efficient tool for the development of new low-dust combustion technologies since it
predicts local fine particle formation in dependence of relevant influencing parameters and thus leads
to a better and deepened understanding of the underlying processes.
The ash deposit and fine particle formation model is currently being further developed by means of
deposit probe experiments in cooperation with BIOENERGY 2020+ GmbH. Moreover, an enhanced
model for the prediction of ash deposition formation on convective heat transfer surfaces is currently
being developed. The model is based on the CFD heat exchanger model and the deposit formation
model described above. Additionally, models for a more accurate description of the release of ash-
forming vapours during biomass combustion on the grate as well as the formation of fine particulates
(regarding the distribution of particle sizes) and their influence on ash deposit formation will be
developed. The extension of deposition formation modelling to convective heat exchanger sections is
of special importance, since ash deposit formation causes problems in these regions especially if they
are exposed to high temperatures (e.g. superheaters).
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 20
CFD simulation of NOx formation in biomass furnaces
The reduction of NOx emissions is a very important issue due to ever stricter emission limits. In order
to meet these requirements an extensive amount of R&D work has already been performed. This work
focuses on the implementation of N-release functionalities and a NOx formation model in the CFD
routines of BIOS in order to develop an efficient design and prediction tool. This model consists of:
Extension of the empirical grate combustion model to include the most relevant NOx precursor
species NO, NH3 and HCN in the empirical combustion model
Eddy Dissipation Concept for turbulence / chemistry interactions
Detailed chemical kinetics (Kilpinen 92) and reduced kinetics (Kilpinen 97-skeletal)
ISAT (in-situ adaptive tabulation) algorithm for run-time tabulation of the reaction kinetics
(reduction of CPU time)
Simulated mole fraction profiles of NH3 (right) and NO (left) in the symmetry plane of a pilot-scale
biomass grate furnace and comparison of measured and simulated NOx emissions at boiler outlet
The figure above shows the comparison of measurements and simulations for the investigated
biomass grate furnace with air staging (fuel investigated: fibreboard) concerning NO (main NOx
component in a biomass furnace) and NH3 (usually the most important NOx precursor in a biomass
furnace). Very good qualitative and quantitative agreement was obtained between the measured and
simulation results regarding NOx as well as the precursors NH3 and HCN for two different operating
conditions of the furnace (oxygen-lean and oxygen-rich conditions in the primary combustion zone). In
order to save CPU time, a reduced mechanism was also applied and validated for lab-scale flames
and for fixed bed biomass grate furnaces of different scale. Good qualitative agreement between
simulated and measured NOx emissions was achieved for all applications with lower CPU time.
Hence, the NOx formation model can be applied to simulations for the performance of sensitivity
analyses concerning the influence of furnace geometry as well as plant operation and air staging on
NOx formation.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 21
NOx emissions TFN/TFNin
PA
PCZ
secondary
air nozzles
SCZ
NOx reduction
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
Iso-surfaces of NOx concentrations [ppmv w.b.] (left) and of the local TFN/TFNin ratio [-] (right) in a
vertical cross-section through the axis of a 20 kW underfeed multi-fuel boiler at nominal load
Explanations: fuel: straw; fuel-N = 0.54 wt.% d.b.; λtotal= 1.71; λprim = 0.69; TFN (total fixed nitrogen):
sum of all moles of nitrogen contained in NO, NH3, NO2, HCN and N2O; TFN/TFNin: TFN in the flue
gas related to TFN released in the fuel bed and introduced via the recycled flue gas (TFNin)
The figure above exemplifies the simulation results for a 100 kW multifuel furnace. It is shown that the
formation and reduction of nitrogen oxides mainly takes place in the PCZ and in the region of the
secondary air nozzles. Looking at the TFN/TFNin ratios it is possible to identify the regions of NOx
reduction (the smaller the ratio, the more NOx precursors (HCN, NH3 and NOx) are reduced to N2). In
the example shown below it can be seen, that NOx is mainly formed in the outer, oxygen-rich region of
the PCZ and that it is reduced in the inner, oxygen-lean region of the PCZ.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 22
Simulation of cyclones, particle separators and filters
The range of simulation services of BIOS also includes the CFD-based design and optimisation of
cyclones, particle separators and filters. In this case the simulations cover flow and temperature
distributions, the calculation of particle separation rates as well as of particle impaction and erosion
rates on the walls.
The following figure shows simulation results for a cyclone of a circulating fluidised bed combustion
plant. The comparison of erosion simulation results with observations (photo) showed good qualitative
agreement of the calculated zones of high erosion rates with locations at the plant where strong
erosion was observed.
Erosion rates observed at the wall of a circulating fluidised bed furnace (left) qualitatively compared
with calculated erosion rates (right)
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 23
Ongoing enhancements and future objectives of CFD simulations
Gas phase combustion
Future developments should include models for the consideration of gas streaks caused by
channelling in the fuel bed. Furthermore, the models for gas phase combustion should be adapted to
low-turbulence zones in biomass furnaces (especially relevant for small-scale furnaces), in order to
improve the prediction accuracy.
Ash deposit and fine particulate formation in biomass fired boilers
Simulations and case studies demonstrated the necessity of a more fundamental description of ash
related problems such as slagging of the combustion chamber and aerosol formation. The in-house
deposit formation model for biomass fired boilers is thus being further developed and coupled with the
CFD heat exchanger model within a collaborative project of BIOS and BIOENERGY 2020+ GmbH.
This enables the modelling of ash deposits in the combustion chamber and the whole boiler including
the convective sections. An improved model for the formation of fine particles forms another essential
extension of the simulation routines.
Corrosion in biomass fired boilers
Material corrosion of steel surfaces in biomass combustion and boiler plants is of major importance
especially when firing biomass fuels with high contents of chlorine, sulphur and alkali metals (waste
wood as well as agricultural fuels) but also for conventional wood fuels (wood chips, bark) with respect
to increasing the steam parameters and thus the efficiency of future biomass CHP plants. Therefore,
within the framework of the large FFG project BioCorrSim (http://www.ffg.at/ausschreibungen/modsim-
computational-mathematics-3-ausschreibung) which is coordinated by BIOENERGY 2020+, basic
models for the prediction of the local corrosion potential in biomass fired combustion and boiler plants
in dependence of relevant influencing parameters will be developed. The simpler approach will be an
empirical model, which describes the corrosion potential in dependence of relevant influencing
parameters like the molar 2S/Cl ratio, flue gas temperature and surface temperature. The second and
more sophisticated CFD-based model considers transport processes and chemical reactions between
the steel surface, surrounding deposit layer and gas phase for the most relevant high temperature
corrosion processes in biomass combustion plants. Both corrosion potential models will then be linked
with an existing and comprehensive CFD based deposit formation model, which provides the local
values of e.g. flue gas temperatures and species concentrations as input values for the corrosion
potential models and further allows for a 3D simulation of the local corrosion potential in dependence
of the influencing parameters. These new models will enable the 3D simulation of the local corrosion
potential in the plant in dependence of influencing values like fuel and furnace temperature.
Solid biomass conversion in fixed beds
While CFD simulations are successfully being applied for the simulation of flow and gas phase
combustion in biomass grate furnaces no engineering model for the 3D simulation of solid fuel
combustion on the grate is available so far. Therefore, within the framework of several R&D projects in
cooperation with BIOENERY 2020+ models for solid biomass conversion on the grate are being
developed and linked with the gas phase CFD models. The basic model already developed is based a
2-step approach. In a first step the movement of the particles in the packed bed is described with a
non-reacting multi-flow simulation (Euler-Granular Model). In a second step, the conversion of the
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 24
particles along their trajectories is calculated with a layer model for thermally thick particles with
temperature gradients inside which is embedded in a Lagrange model. This enables the 3D simulation
of the processes during solid biomass combustion in dependence of relevant influencing parameters
for the first time.
Carbon content of the ash: Simulation: 0,8 Gew.% TS Analyses: ca. 1,0 Gew.% TS
Maximum particle temperature: Simulation: 1100 – 1150 °C Measurements: ca. 1100 – 1200 °C
Iso-surfaces of flue gas temperature in the furnace axis [K] (left); particle trajectories coloured by
particle temperature [°C] – top view (middle); photo of the fuel bed taken from the top of the furnace
(right)
Explanations 20kW underfeed stoker pellet furnace
In the picture above the simulation results (flue gas temperatures and particle tracks coloured by
particle temperatures) of a 20 kW pellet furnace are shown. Moreover, a photo of the fuel bed taken
from above is depicted for the purpose of a qualitative comparison with the simulation results. The
calculated peak temperatures of the fuel particles are in good qualitative agreement with
measurements at a lab-scale packed-bed reactor. Moreover, the calculated carbon content of the ash
is in the same range as empirical values from different test runs.
In a next step a model based on the Discrete Element Method will be implemented in the simulation
routines for the purpose of a more accurate description of movement and heat transfer of the particles
in the packed bed and the linked processes of solid fuel conversion. Furthermore, release models for
nitrogen species and ash forming elements will be implemented in order to simulate the influence of
solid fuel combustion on NOx and fine particulate formation.
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 25
Selected references
CFD-based design, refurbishment and/or optimisation of furnaces, gasifiers, stoves, boilers and flue
gas cleaning systems for biomass, waste wood and sewage sludge combustion plants in order to
reduce emissions and increase the availability and efficiency of such systems:
Simulation, further development and optimisation of electrostatic precipitators for biomass
combustion plants; client: Scheuch GmbH, Aurolzmünster (Upper Austria, Austria).
Project period: 2001/2002
Simulation and support of biomass furnace and boiler design for the CHP plant Grossaitingen
(Bavaria, Germany) / Josef Bertsch Gesellschaft m.b.H. & Co, Bludenz (Vorarlberg, Austria).
Biomass grate furnace and water tube steam boiler; nominal thermal capacity: 16.5 MW biomass steam
boiler; nominal electric capacity: 5.0 MW steam turbine; fuel: waste wood; project period: 2001-2003
Simulation and support of biomass furnace and boiler design for the CHP plant of LINZ STROM
GmbH, Linz (Upper Austria, Austria).
Biomass grate furnace and water tube steam boiler; nominal thermal capacity: 26.0 MW biomass steam
boiler; nominal electric capacity: 7.0 MW steam turbine; fuel: untreated woody biomass including bark; project
period: 2002/2003
Simulation and support of the design and optimisation of the new "i-series" wood log fired stoves
of the company HAAS + SOHN OFENTECHNIK GMBH, Puch (Salzburg, Austria) with a nominal
thermal load of 8 kW
Wood log fired stoves; nominal thermal capacity: 8 kW stove; fuel: wood logs; project period: 2007/2008
Simulation and support of the design and optimisation of the BIOTEC series biomass grate
furnaces of the company Uniconfort srl., San Martino di Lupari (Italy)
Biomass grate furnace and fire tube boiler; nominal thermal capacity: 3.5 MW - 5.8 MW biomass hot water
boiler; fuel: untreated woody biomass; project period: 2008/2009
Simulation and support of the design and optimisation of a biomass grate furnace of the company
VYNCKE ENERGIETECHNIEK N.V., Harelbeke (Belgium)
Biomass grate furnace and fire tube boiler; nominal thermal capacity: 6 MW biomass hot water boiler; fuel:
woody biomass; project period: 2008/2009
Simulation and support concerning the reduction of erosion tendencies in the lining of the cyclone
evaporator of the biomass CFB combustion plant in Strongoli/ Biomasse Italia S.p.A., Strongoli
(Italy)
Biomass CFB furnace and water tube steam boiler including cyclone evaporator; fuel: woody biomass and
agricultural residues; project period: 2008/2009
Simulation and support of the design and optimisation of the prototype of a new pellet furnace of
Windhager Zentralheizung GmbH, Seekirchen (Salzburg, Austria)
Biomass fixed bed furnace and fire tube boiler; nominal thermal capacity: 15 kW biomass hot water boiler;
fuels: wood pellets; project period: 2007-2009
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 26
CFD based design of the prototype of a new pellet and wood chip-fired furnace of KWB Kraft &
Wärme aus Biomasse GmbH, St. Margarethen/R. (Austria); introduced into the market as KWB
TDS Powerfire 150 boiler series, received the “Energie Genie 2004” award from the Austrian
Ministry of the Environment in co-operation with the regional energy agency “O.Oe.
Energiesparverband” as well as the “Energy Globe Award 2004” (special category “most
innovative product”)
Rotary grate furnace with a cyclone combustion chamber and fire tube boiler; nominal thermal capacity: 0.15
MW biomass hot water boiler; fuels: wood chips and wood pellets; project period: 2002/2003
Simulation and support of biomass furnace and boiler design for the Kufstein CHP plant TIWAG-
Tiroler Wasserkraft AG, Innsbruck (Tyrol, Austria)
Biomass grate furnace and water tube steam boiler; nominal thermal capacity: 24.5 MW biomass steam
boiler; nominal electric capacity: 6.5 MW steam turbine; fuel: woody untreated biomass including bark; project
period: 2002-2004
Simulation to support the analysis and optimisation of an existing sewage sludge combustion plant
– Andritz AG, Graz (Styria, Austria)
Pulverised fuel furnace with rotary combustion chamber; nominal fuel power related to NCV: 3.7 MW; fuel:
sewage sludge; project period: 2005-2006
Simulation and support of the design of a mixed fuel furnace and boiler - Thermische
Verwertungsanlage Schwarza (TVS) in Thuringia, Germany – Oschatz GmbH, Essen (Germany).
Water cooled moving grate furnace with water tube steam boiler; nominal fuel power related to NCV: 31.0
MW; fuel: mixed fuel with paper residues (rejects) as well as waste from mechanical/biological waste
treatment; project period: 2006
Simulation and support of the development of a new multifuel furnace for woody and herbaceous
biomass fuels of the company KWB Kraft & Wärme aus Biomasse GmbH, St. Margarethen/Raab
(Styria, Austria)
Biomass grate furnace with fire tube boiler; fuel: wood chips, wood pellets, olive residues, Miscanthus etc.);
nominal thermal capacity: 8 to 120 kW biomass hot water boiler; project period: 2007-2009
Simulation and support of the development of an optimised concept of a collector for waste heat
recovery from rotary cement kiln of the company Wopfinger Baustoffindustrie GmbH, Waldegg
(Lower Austria, Austria)
Rotary cement kiln; fuel: lignite and refuse derived fuel (paper fibre residues, plastic waste, etc.); thermal
capacity recovered waste heat: 1,3 MW; project period: 2009-2010
Simulation and support of the design and optimisation of the prototype of a new pellet furnace for
low-energy houses of the company Windhager Zentralheizung GmbH, Seekirchen (Salzburg,
Austria)
Biomass fixed bed furnace with fire tube boiler; nominal thermal capacity: 1,7 to 6 kW biomass hot water
boiler; fuel: wood pellets; project period: 2009-2010
BIOS BIOENERGIESYSTEME GmbH, Graz, Austria – key information regarding CFD simulations 27
Simulation and support of the design and optimisation of a grate furnace especially designed for
peat combustion for the company POLYTECHNIK Luft- und Feuerungstechnik GmbH,
Weissenbach (Lower Austria, Austria)
Grate furnace with thermal oil boiler; nominal thermal capacity: 13 MW thermal oil boiler; fuel: peat; project
period: 2010
Simulation and support of the design and optimisation of the prototype of a new 100 kW pellet
furnace of the company Fröling Heizkessel- und Behälterbau GmbH, Grieskirchen (Upper Austria,
Austria)
Biomass fixed bed furnace with fire tube boiler; nominal thermal capacity: 100 kW biomass hot water boiler;
fuel: wood pellets; project period: 2010-2011
Simulation and support of the development of a Low-NOx furnace for „new“ biomass fuels in the
medium size range of the company Josef BINDER Maschinenbau- und Handelsges.m.b.H.,
Bärnbach (Styria, Austria) as a subcontractor of the Institute for Process and Particle Engineering,
Graz University of Technology
Biomass grate furnace with hot water or steam boiler; nominal thermal capacity: 100 kW - 10 MW; fuel: short
rotation coppice, agricultural residues (maize cobs; grass pellets); project period: 2010-2011
Simulation and support of the development of a new biomass grate furnace technology for fuels
with high water and ash contents in the size-rage from 700 kW to 13 MW for the company Mawera
Holzfeuerungsanlagen Gesellschaft m.b.H, Hard (Vorarlberg, Austria)
Biomass grate furnace with hot water boiler/ steam boiler / thermal oil boiler; nominal thermal capacity: 700
kW - 13 MW; fuel: biomass fuels with high water and ash contents (freshly harvested short rotation coppice,
wood chips with high contents of bark, needles and mineral impurities, landscape preservation wood, stools);
project period: 2011-2012
Simulation and support of the design and optimisation of different stoves of the company RIKA
Innovative Ofentechnik GmbH, Micheldorf (Upper Austria, Austria)
Wood log fired or pellet fired stoves; fuel: wood logs or pellets
Simulation and optimisation of different biomass grate furnaces of the company POLYTECHNIK
Luft- und Feuerungstechnik GmbH, Weissenbach (Lower Austria, Austria) in the medium and large
size-range
Biomass grate furnace with hot water / steam / thermal oil boiler; fuel: woody biomass fuels
Simulation and support of the design and optimisation of the next generation CHP plant based on
a hybrid biomass and solar system - EU project "Sunstore 4", Marstal (AERO, Dänemark)
Biomass grate furnace with thermal oil boiler; nominal thermal capacity: 3.24 MW biomass thermal oil boiler +
0.91 MW thermal oil economiser; nominal electric capacity: 750 kW ORC process; fuel: short rotation coppice
(willow); project period 2010-2011.