Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Sr.
no.
Description of item Unit Quantity Rate Amount
Demolition & Pest Control Works
Demolition Rates to includes removal of debris from site to nearest dumpyard of NMMC at regular
intervals.House keeping on day to day basis from start to completion of project and handover to SBI GCSOC .The
demolition rate to be inclusive of carting away the debris from the building premises including all royalties etc.
1 Carefully removal of Existing floor tiles of toilets withoutdisturbing the existing brickbat coba/ waterproofing
treatment and disposal of debsris out of premises.
SMT 20 350 7000
2 Providing Pest control and Anti-termite treatment by appointing a specialised agency as per the specifications
mentioned by the Bureau of Indian Standards and Agencies specifications (whichever is higher), for General Civil,
Plumbing,/ Drainage and timber. The termite treatment has to be done in two stages as pre-renovation and
during renovation. Vendor should provide 2 yrs warranty on completion of entire work .
SMT 340 225 76500
3 Making trenches of 150mm wide for raceways by cutting existing flooring/ walls, breaking the flooring & mortar
and removal of debris. Providing necessary base for raceways with 1:3:6 P.C.C & filling the trench with 1:2:4 IPS in
line and level, curing etc. complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer incharge .
RMT 42 100 4200
4 Carefully Removal of Existing wall tiles of toilets, panelling from wall/ column , false ceiling with frame, elecrical
condutes with wires/ cable and services related all elements / existing Cassette AC Machine to be removed
safely/carefully and hand over to Bank , Remove the unwanted/ unservisable materials, other debries from site
to NMMC approved dumpyard.complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineers.
L/S 1 40000 40000
Total for Demolition & Pest Control Works 127700
B MASONRY WALLS & PLASTER
1 Providing and constructing autoclaved 100 mm thick wall of 100mmX 240mm X 600mm Siporex Block in proper
line and levell, at all levels in cement mortor 1:4 (1 cement and 4 river sand) using standard size of blocks,
including all scaffolding, staging, curing, all lifts, raking of joints, all labour etc. complete as directed. rate shall
include providing concrete binders in proportion 1:2:4, 75mm thk reinforced with 4 nos of 8mm dia Fe 415 bars,
RCC binder to be at every 1mtr interval from floor level. the rate to be inclusive of cost of reinforcement and
formwork, cover block for reinforcement and all other incidental charges etc. The rate shall also include closing
the gap between the masonary and RCC beam/ slab finished to required slope as directed by engineer in charge.
Note : - The width of joints not to exceed 10mm. The Siporex block to withstand the standard fire for 240mins
under uniform compressive load of 15 kg/m2 as per IS: 3809, BS : 476 part 20 and ISO 834 with certification.
SMT 25 1200 30000
2 Providing internal cement plaster, 12mm to 18mm thick in a single coat of cement mortar 1:4, (1unit- cement,
4unit- fine screened sand), to concrete and masonry surfaces in all positions including of hacking of RCC surfaces,
all plaster works will have provision of chiken mesh 9" vide at joint of masonary and RCC beam/ slab, preparing
surface before applying plaster, adequate curing, necessary scaffolding . grooves, sills, pattas etc complete the
work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 125 550 68750
3 Providing and Laying IPS of 1:3 of average thickness of 18mm over the entire floor area in line and level as
indicated by the architect with proper compaction inclusive of adequate curing etc.The finished surface to be
smooth and level in power trowel finish without any undulation. Cost to incl. Finishing of edges near junction-
boxes, etc.. Removal of relevant debris from the site, on a day-to-day basis.Any damage to the below floor premises to be born by vendor, all precautions and preventive measure shall be part of the scope, no additional charges shall be paid
.complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 20 425 8500
4 Making RCC lintels of size 150mmx150mm cast in situ in 1:2:4 cement concrete ratio (1unit-cement: 2unit- sand,
4unit- course aggregate) with 4 nos of 8mm TOR steel reinforcement with 12mm cover, necessary shuttering,
curing, compacting, bending of steel reinforcement etc. complete the work as per site conditions and instructions
of Architect, SBI/SBIIMS engineer.
RMT 3 900 2700
TOTAL FOR MASONRY WALLS & PLASTER 109950
C CIVIL WORKS
1 P/f frosted 12mm thk toughened glass partitions with full length L bracket complete with all accessories. max
size 1200 x 700mm (as per dwgs) complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
NOS 2 4000 8000
2 P/f 600mm wide counters for wash basin made of 19mm thk. Granite including 300mm wide facia supported on
25mm thk kaddapa including cutting of required size hole for wash basin,drainage etc Rate inculsive of edge
polishing of all exposed edges & making cutouts for pillar cock, etc. as per dwg. P/f Granite to all exposed portion
of wash basin counter. complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
RMT 3.75 15000 56250
3 P/f Double Granite Door Jamb in 100mm & 75mm wide with smooth straight edge with mirror polish & provision
of cutout for lock lever / baby latch. complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
RMT 12 1600 19200
4 Providing and laying 1200mm x 600mm x10mm Antiskid tiles of approved make and approved sample in pattern as per detailed drawings on average 25mm thick cement mortar bed of proportion 1:4. The rate should be inclusive of surface
preparation, giving necessary slopes, cleaning the joints and grouting them with approved white cement paste with
pigmented additives to match shade of the tile. Tile shall be free from any colour & size variation. Cost all inclusive of
Insurance, Freight,loading- Unloading at site and covering the same with pop. Rate will not be paid extra for cement
mortar bed upto 75 mm. thk. complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 20 2500 50000
5 Providing and Fixing 1200mm x600mm x 8mm vitrified tiles to wall of approved make, colour and in pattern as
per detailed drawings in neat cement paste . The rate should be inclusive of Base coat in 1:4 CM, surface
preparation, cleaning joints and grouting them with approved white cement paste with pigmented additives to
match shade of the tile. Tile shall be free from any other colour & size variation. Cost all inclusive of S.S (brush finish) corner edge profile as per details.complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
SMT 70 2500 175000
BILL OF QUANTITY
I) Interior & Furnishing work
CIVIL INTERIOR & FURNISHING WORK
A
6 P/F 300mm wide Granite for tread with granite for trade with required adhesive and smooth straight edge with
mirror polish/ moulded edge . The rate is inculsive of P/f 19mm thick ply IS:710 to support the granite steps on
existing MS frame work, complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
SMT 12 6000 72000
7 P/F 150mm wide Granite for riser with granite for riser with required adhesive and smooth straight edge with
mirror polish.. The rate is inculsive of P/f 19mm thick ply IS:710 to support the granite on existing MS frame work.
complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 15 6000 90000
8 Providing, supplying, mixing and applying two coats of approved make -Supercret ready-to-use acrylic polymer of,
modified cement base, flexible water-proofing slurry to a thickness of 3mm over the existing surface of Brickbat
coba/ waterproofing treatment. including preparation of surface, finishing, curing etc. all complete as specified
by the Architect, as per manufacturer's specifications and as directed. Vendor has to provide guarantee for 10yrs complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
Note:-
Make - Sunanda , Dr FIXIT and Equivalent
SMT 25 1100 27500
TOTAL OF CIVIL WORKS 497950
D PARTITIONS
Note: Necessary cutouts shall be provided for taking of supply and return air ducts/openings above false ceiling
which shall be neatly finished after fixing of ducts thereby leaving no gaps.Rate shall Include making opening &
closing of same for all services.(Applicable to all partitions) : Salwood to be provided whereever required for extra
support to fix skirting, doors, storages, writing boards, glass boards, As per dwg. design given by the architect. (
All Framing shell be having a proper fitting with existing MS structure cost shall be inclusive of necessary
fabrication ,Cutting ,driling fixing, joining with existing structure in good manner etc.)
1 Providing and fixing Aluminium frame work for partition made of Aluminium section of size 50mm X 50 mm X
1.8mm comprising of vertical and horizontal at 600 mm c / c. both ways & fixing with vertical \"T" member from
true ceiling.complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 160 1600 256000
2 Providing and installing glass wool of 50 mm thick having 34 Kg/Cum density for full height partition complete
the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 160 250 40000
Note: The ply/gypsum shall be stopped 75mm above bottom of false ceiling. Partition will be measured only upto
the false ceiling bottom for payment under this item. Necessary cutouts shall be provided for taking of supply
and return air ducts/openings which shall be neatly finished after fixing of ducts thereby leaving no gaps. All
opening above and below shall be closed using HILTI OR Equ. SealeantProviding and fixing 75mm thick full height
partition which Excluding framework and glass wool insulation, cladded with material as specified in below items
and fixed with 35mm Metalfold screw & Fevicol upto 75mm above false ceiling level, with grooves as directed,
necessary cut-outs for switchboards, volume control, data plates & all types of conduits etc. Fevicol SR to be used
for pressing the laminate.Inclusive of 12mm groove at the junction of partition and gypsum false ceiling,
completed in all respects as per Architect's Instructions.
3 P/F 12 mm thk BWR IS -303 ply on both sides and finished with 1 mm thk laminate of approved make and colour.
Cost shall include fixed with 35mm Metalfold screw, necessary grooves as per dwgs. Complete the work as per
site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 15 3500 52500
4 P/F single layer 12 mm thk BWR IS -303 ply one sides and finished with 1 mm thk laminate of approved make and
colour. Cost shall include necessary grooves as per dwgs. Complete the work as per site conditions and
instructions of Architect, SBI/SBIIMS engineer.
SMT 100 2000 200000
5 P/F double layer 12 mm thk BWR IS -303 ply one sides and finished with 1 mm thk PVC laminateof approved
make and colour. Cost shall include necessary grooves as per dwgs/ iComplete the work as per site conditions
and instructions of Architect, SBI/SBIIMS engineer.
SMT 25 3200 80000
6 P/F 12 mm thk BWR IS -303 ply Cost shall include necessary Cut out for services. Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 140 1000 140000
7 P/F 12 mm thk mdf on one side and finish with paint of approved make and shade over a coat of primer putty.
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 30 600 18000
8 P/F 200mmx200 mm thk. portal made out of 18mm thk. Ply IS:303 BWR and finish with + 1 mm thk.appved make
and colour Laminate with Aluminium frame work for necessary support and including all hardware and
accessories and sliding door provision in portal with openable system for service to sliding door mechanism.
asper Architectural detail dwg.Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
Rmt 10 4000 40000
9 P/F 18mm BWR IS -303 ply boxing with PVC laminate fixing For LED screen @150 mm deep and Niche size /detail
To be as per approved design, .Rate shall be inclusive of all necessary 50x50mm thk aluminium Framing, Cove
light detail, Back drop ply ,Anodized Aluminum Hat profile / corner guard as per approved design.Complete the
work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 35 3500 122500
11 Glazed partition:
Providing and Fixing Aluminium Modular Glass Partition, 25MM X 100MM profile , Silver anodize natural including
Glass to glass I, T, L joint and gaskets, with 10mm Clear toughened glass-Saint Gobain/Asahi/equivalent make
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 20 4000 80000
12 Providing and Fixing Aluminium Modular Glass Partition, 50MM X 100MM profile , Silver anodize natural including
Glass to glass I, T, L joint and gaskets, with 12mm Clear toughened glass-Saint Gobain/Asahi ( Single panel glass Ht
- 3.3 MTR ). Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 35 4000 140000
13 Providing and fixing of Full Height JEB Fineline Curve Partitions systems of 25 x 25 mm thick section on all four
sides for the partitions using JEB 047 as verticals at the solid partition junction & Horizontals at top & JEB 044 &
JEB 045 at bottom with snap on option for installating glass & JEB 941 as 'T' Section, JEB 884 as corner Section &
JEB 883 as Vertical "I" Section between Glass to glass joint from FFL upto from FFL upto 2750mm. Complete in all
respect considering 10 mm Curve toughened glass with double sided adhesive tapes for glass to glass butt
joints..Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
1.5 11000 16500
14 Providing and fixing 12.5 mm thk. single layer Gypsum sheet from both side. Square end and tapered edges of the
boards are to be finished so as to have a flush look which includes filling and finishing with jointing compound,
joint paper and 2 coats of Drywall top coat suitable for Gypsum upto primer level as per India Gypsum
Specs.same as above but only on one side Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
SMT 45 375 16875
15 P/F 18 mm thk Bison board panelling from inside in UPS/ Switch room including all nessesary hardware. The rate
is inculsive of painting in minimum 2 coats over a coat of primer, putty etc. Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 45 1200 54000
TOTAL OF PARTITIONS 1256375
E PANELING & FINISHING ITEMS
1 Providing and fixing aluminum skirting 75mm wide Black powdercoated Make Bottomline /parallel. Complete
the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
RMT 170 250 42500
2 Providing and fixing mirror paneling in areas indicated using 12mm thk Marine ply backing over 6mm thk.'pre-
approved' mirrorwith Bevealed edge from all four sides as per dwg including LED light and PVC/Aluminium
powdercoated edge profile , The mirror to be fixed with two way tape of 3M make. Complete the work as per
site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 5 4000 20000
3 Providing and applying patterned vinyl wall paper on partitions / walls all inclusive with complete application and
protective covering until handover. The Rate is inculsive of base preparation. Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 100 2000 200000
4 Providing & applying 6mm toughened lacqured glass panelling including back ply 12mm thick IS:303 BWR & all
glass holes / cutting fixing with specified 3Mm or Equivalent make glue etc Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
Note:- Make- saint gobin/ modi /Form 5.
SMT 35 3500 122500
5 P/f false ceiling made out of 19mm thick IS:303 BWR ply batten frame work, externaly finished in 1.0mm thick.
laminate .Size - 4' x 4' Hollow box frame work. Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
SMT 10 2000 20000
6 Providing and fixing Artificial green wall.
Make - Moss type. Plant as per approved by architects, Including 12 mm thk BWR IS -303 ply with one side black
japan and front side shall be finished with black Oil paint Complete the work as per site conditions and
instructions of Architect, SBI/SBIIMS engineer.
SMT 15 10000 150000
7 Providing and fixing pre Printed , Sound Absorbers Eco Panel, Thickness: 10 MM, panel board on finished surface
as per detail dwg including fixing with Appropriate Adhesive , Joint with 'V' Grove as per instruction and approved
by architects. Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 80 3750 300000
TOTAL OF PANELING & FINISHING ITEMS 855000
F DOORS AND DOOR FRAMES
1 Providing and fixing solid core flush door 40-45mm thk as per design and detail to be finished in Black PVC
laminate at one side and finish the other side with laminate of approved make, shade. The door shall be
mounted on heavy duty ball bearing hinges inclusive of concealed door closer with 90 deg stop . All door margins
to be finished with TW lipping & matching colour polish to match the laminate.the rate is inclusive of P/f pre-
approved 450 mm long handles to be fitted horizontally / vertically as per dwgs or instructions, all necessary
hardware like locks etc.complete including double rebate aluminium door frame of size 25 x 50 mm. Complete
the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer. Approx Dorr size 1050 X 2400
mm
NOS 1 22000 22000
2 Do as above. Door size will be approx 1050 + 450 X 2500mm NOS 1 35000 35000
3 Providing and fixing solid core flush door 40-45mm thk as per design and detail to be finished in laminate both
side of approved shade & make, mounted on heavy duty ball bearing hinges inclusive of concealed door closer
with 90 deg stop . door frame in granite finish, All door margins to be finished with TW lipping Cost of the door to
be inclusive of pre-approved 450 mm long handles to be fitted horizontally / vertically as per dwgs or instructions,
all necessary hardware like locks etc.Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
NOS 2 20000 40000
4 Same as above item No1 but the laminate shall be fire rated upto 2 hour on both sides of approved make, colour
ncluding Door Frame. Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
NOS 2 28000 56000
5 Providing & fixing glazed door of size approximately, 900X2400 fabricated with 12mm thk Toughen glass on floor
spring of DORMA/ make, all sides edge polished.Cost of the door to be inclusive of pre-approved 600mm long
handles to be fitted horizontally / vertically as per dwgs or instructions and necessary holes to be drilled in the
glass as desired. Cost to include alum. door frame with style as per details.Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
NOS 1 25000 25000
6 Providing and fixing 100 x 75 mm wide (uptill false ceiling) with support provided from true slab, hollow wooden
boxing for mounting access control panels / or as partitions made out of 19mm thk IS:303 BWR ply finished in
approved laminate, all complete as per details / drawings. Complete the work as per site conditions and
instructions of Architect, SBI/SBIIMS engineer.
RMT 25 1000 25000
7 P/F Trap doors to house AC ductable units, service trap door made out of 50mm x 38mm aluminum frame and
19mm thk IS:3030 BWR ply consisting of openable panels. The shutter to be finished in 1.0mm thk laminate of
approved shade and color, on both side, and all wooden members shall be finished in paint. Complete the work
as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 5 3500 17500
8 P/f automatic acoustical drop seal on doors NOS 3 1500 4500
9 Providing & fixing double leaf glazed door of size approximately, 1500x 2400 ht fabricated with 12mm thk
Toughen glass on Sensor system of DORMA/ make, ESA200 Door all sides edge polished.Cost of the door to be
inclusive of all required cutout, fittings ,Channel as per dwgs or instructions and necessary holes to be drilled in
the glass as desired. Cost to include as per details.( sensor system to be inclusive as per instruction with all kinds
of wiring and instalation ) 5 year warrenty Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
NOS 1 200000 200000
TOTAL OF DOORS & DOOR FRAMES 425000
G STORAGES
1 Providing and fixing louvered shutters storage in 19mm thk IS:303 BWR ply finish with approved colour, make
laminate on all exposed area as per design detail with powder coated grill. Approx Size -1.93X2.4 Mtr Complete
the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 5 8000 40000
2 Providing and fixing Shoe Stand storage with flipdown shutter in 19mm thk IS:303 BWR ply as per design detail
finish with approved make colour laminate Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
SMT 3 8000 24000
3 P/f storage made out of 19mm thk ply finished in 1mm laminate from all sides with glass /acrylic designer shelf
box as per details / instructions of site in charge & shown in the dwg. with necessary hardware & fittings.
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 2 9000 18000
4 P/F Hydraulic Folding table to be made out in 19 mm thk IS:303 BWR ply finished with Black PVC laminate at all
side edge to be finished with PVC liping or Teak wood with Melamine Polished and Hydraulic chanel to be use
as per details / instructions of site in charge & shown in the dwg. with necessary hardware & fittings.(Approx size
1300x500mm -2Nos and size 1900x550mm -1Nos.) Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
SMT 3 12000 36000
5 Providing and fixing Block board flush door 25/35 mm thk as per design and detail to be finished in 4mm thick
Indian veneer in approved shade on exposed surface , Internal surface to be finished in approved make & shade
0.8mm laminate, mounted on heavy duty hinges incl L N key Lock 2 Nos per shutter . All door margins to be
finished with TW lipping & colour polish to match laminate Cost of the door to be inclusive of all necessary
hardware like locks etc.complete including double rebate alu door frame of size 25 x 50 mm with Teak wood
framing. Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 15 2500 37500
6 P/F 150 mm thk Ply wood portal finished in approved laminate as per detailed drawings. SMT 10 3700 37000
7 P/FMultipurpose table made in 19mm thk IS:303 BWR ply with approved make 1 mm laminate with Drawer
shutter and inclusive of necessary hardware. Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
SMT 2.25 8000 18000
8
TOTAL OF STORAGES 210500
H MISCELLANEOUS ITEMS
1 Providing and fixing roller honeycomb blackout blinds comprising of Jute/ Jaquared fabric with minimum openess
factor of 8% and max of 14% as per AS stand.The roller mechanism shall be a moulded unit made from engg
grade plastic polymer with steel pring support.|The fabric shall be finished on the sides with edge tape duly
welded for waviness control.The fabric shall be attached to roller tube with high quality shelf adhesive tape,with
motarised operation.Operational action shall be smooth. Complete the work as per site conditions and
instructions of Architect, SBI/SBIIMS engineer.
Note:- Honeycomb / Marvel / Vista / Mac / Gaalicha or Equivalent Make
SMT 90 2000 180000
2 Providing & fixing pelmet of approx size 150mm X 300mm for blinds in 19mm IS:303 BWR ply finished with
laminate on all exp[posed surface as per architects design/details/ instructions
RMT 45 1500 67500
3 Supply & Installation of 3M Clear view Decor with approved artwork digitally reproduced with water-based inks
certified to have no hazardous air pollutants. Self-adhesive, optically clear, bubble-free installation to be done on
clean glass , by Authorized Installers only. 3M interior warranty for a period of 3 years to be submitted along with
invoice by 3M directly to customer. Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
SMT 3.5 1600 5600
4 Providing and fixing signages for meeting rooms, toilets, pantry doors etc.in brushed steel plate.Plate size of
100mm x 200mm with text of approved style and font as per instructions of the architect.
NOS 12 1000 12000
5 P/F fire exit map of size Size max 18 " X 12 ". ( Sample Material to be approved from Architect/SBI/SBIIMS
Engineer.
nos. 10 3000 30000
6 P/f glow fire exist sign boards as per details nos. 8 500 4000
7 P/f SS (304 Grade) profile on edge joint. Corner Beading as per directed. Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
RMT 150 250 37500
8 Supply & Installation of 3M Envision Wrap Non-PVC Wall Décor Pro where in Envision Wrap LX480Cv3 will be
used as a base material for printing and 8550M will be used as a Over laminate to protect the print from fading,
which will come in a matte finish with approved artwork digitally reproduced with water-based inks certified to
have no hazardous air pollutants. Self-adhesive, bubble-free installation to be done on a smooth, dust free putty
surface that has a coat of oil-based primer, by Authorized Installers only. Certificate of image license and 3M
Interior Warranty for a period of 5 Years to be submitted on completion of work. The rate is inclusive of Base
preparation. Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 30 2000 60000
9 P/F 12mm thick IS:303 BWR ply box framing for junction box approx size -300 x 300 mm. Complete the work as
per site conditions and instructions of Architect, SBI/SBIIMS engineer.
nos 20 150 3000
10 Providing and Fixing fabricated Ms Box 50x50 mm raised flooring with 5 level from +0mm To 750 mm height
raised with 150 mm interval. The size of raise/ false floor shall be Approx 17 mtr length and 8.4 mtr wide
including provision of cove light at each step in MS 'L' Angle .intermidiate support at 1.2 Mtr Intervel. Inclusive
of Anti corrosive Treatment With OIL paint Inclusive of all Joinaries. Structure to be executed as per detail
drawing.. The false floor tiles in approx 600 X 600mm to be made in 25mm thick IS:710 marine ply with black
japan (anti termite treatment) to be layed on Ms raised structure all edge (Cove light provision) to be finished as
per detail drawing. Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 150 4400 660000
11 P/F Bottom Line Alu. Hat Profile 10mm -3mtr Long as shown in the dwg. Complete the work as per site conditions
and instructions of Architect, SBI/SBIIMS engineer.
RMT 100 200 20000
12 P/ F luxury vinyl floor LVT collection 3mm thk +0.5 MM wear layer plank size - 184mm X 950 mm as per
approved design by architects inclusive of brass /wooden finished transist strip etc. (Specification to be match as
per 3mm thk LVT flooring). Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
SMT 50 2600 130000
13 P/S Art Works As per selection including frame ( Size of 600x900) Make - Art tantra Nos. 1 7200 7200
14 P/S of SS finish umbrella stand with individual section and drain tray. Nos. 1 5000 5000
15 P/F Brass transit patti and Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS
engineer.
RMT 15 525 7875
16 Bottom-line corner guards and Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
RMT 60 420 25200
17 Supplying and placing in position soap dispenser with pair of fixing screws and fixing material( Kimberly Clark or
equivalent make). Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
Nos. 4 2000 8000
18 P/F SCOTT Compact Towel System of Kimberley Clark or quivalent make. Nos. 2 3500 7000
19 Providng and fixing single blower hand dryer of Jaquar or equivalent make) Nos. 2 10500 21000
20 P/F of toilet paper holder (ACN-1151N, Jaquar make) complete as per specifications. Nos. 4 1850 7400
21 P/F 3M Floor Mat size 1200X900 mm design as approved by architects, SBI/SBIIIMS engineer Nos. 2 5000 10000
22 Providing and supplying dustbins of m.s perforated and black powder coated finish as approved by the architect.
Approx size 300mm dia and ht. 450mm.
NOS 17 800 13600
23 Providing and fixing pre laminated modular toilet partitions, with 18mm thk. SS brush finish top & bottom rail
along SS legs including door size of 750mm X 2100 mm all complete required accessories. As per dwg. by
architect. Merino/ matrix make. Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
SMT 20 8000 160000
TOTAL OF MISCELLANEOUS WORKS 1481875
I PAINTING , CEILING & POP WORKS
1 Providing and applying POP punning to walls of avg. 12mm thickness to line level and plumb; required punning to
be undertaken and completed inworkman-like manner, to ensure desired finishing standards, as per approval(s)
of the Architects.Including all the skirting grooves. cost to include PVC corner profiles as per details.Complete the
work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 125 300 37500
2 Providing and applying three coats of pre-approved Acrylic emulsion paint to walls partitions etc. including
surface preparation with two coats of putty, primer and sanding all complete. Complete the work as per site
conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 125 300 37500
3 Do as above but plastic emulsion paint,Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
SMT 320 250 80000
4 Gypsum False Ceiling:
P/F suspended Gypsum False Ceiling which includes providing and fixing G.I. Perimeter Channels having One
Flange of 20mm and another flange of 30mm.and a web of 27mm.along with perimeter of ceiling, screw fixed to
brick wall / partition with the help of Nylon sleeves and screws at 610mm.centres. Then suspending G.I.
intermediate channels of size45mm.,with 2 flanges of 15mm.each from soffit at 1220mm. centres with ceiling
angle of width 25mm.X10mm fixed to soffit with G.I cleat and steel expansion fasteners. Ceiling section having
knurled web of 51.5mm and 2 equal flanges of 26mm.each with lips of 10.5mm. are then fixed to the
intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate
channel at 450mm.centres. 12.5mm.tapered edge Gypboard (conforming to IS 2095 - 1982) is then screw fixed to
ceiling section with 25mm.dry wall screws at 230mm. centres. Complete the work as per site conditions and
instructions of Architect, SBI/SBIIMS engineer.
SMT 110 900 99000
5 PROVIDING AND FIXING GYPSUM VERTICAL FALSE CEILING OF INDIA GYPSUM MAKE WHICH INCLUDES G.I.
PERIMETER CHANNELS OF SIZE 0.55MM THICK (HAVING ONE FLANGE OF 20MM. AND ANOTHER FLANGE OF
30MM AND A WEB OF 27MM) ALONG WITH PERIMETER OF CEILING, SCREW FIXED TO ADJACENT GUPSUM
CEILING WITH THE HELP OF NYLON SLEEVES AND SCREWS AT 610MM CENTRES. THEN SUSPENDING G.I.
INTERMEDIATE CHANNELS OF SIZE 45MM (0.9MM THICK WITH 2 FLANGES OF 15MM EACH) FROM THE SOFFIT
AT 1220MM CENTRES WITH CEILING ANGLE OF WIDTH 25MM X 10MM X 0.55MM THICK FIXED TO SOFFIT WITH
G.I. CLEAT AND STEEL EXPANSION FASTENERS. CEILING SECTION OF 0.55MM THICK HAVING KNURLED WEB OF
51.5MM AND 2 FLANGES OF 26MM EACH WITH CLIPS OF 10.5MM ARE THEN FIXED TO THE INTERMEDIATE
CHANNEL WITH THE HELP OF CONNECTING CLIPS AND IN DIRECTION PERPENDICULAR TO THE INTERMEDIATE
CHANNEL AT 450 MM CENTRES. ALL STEEL SECTIONS SHALL BE MARKED WITH 'GYPSTEEL' ( REGISTERD
TRADEMARK HOLOGRAM)REFER DETAIL DRAWING.Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
RMT 110 200 22000
7 M/F Suspended Rigitone Activ’Air 8/18 Ceiling includes 20x28x30x0.5mm Gypserra™ Perimeter Channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is fixed along the perimeter of existing wall with the help of HILTI
HPS - 1 (6x40) impact anchor at 600mm centres. 25x10x0.5mm Gypserra™ Ceiling Angle {Material-GI(IS513),YS-
260Mpa,Finish-Galvanised 150GSM(IS277)} is suspended by fixing it to the 27x37x25x1.6mm Gyproc® soffit cleat
{GI(IS513)YS-260Mpa,Finish-Galvanised 120GSM(IS277)}. Soffit Cleat and Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513
CR1 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} creating 1000mm x 900mm grid.
15x45x15x0.9mm Gypserra™ Intermediate channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277) fixed
to the ceiling angle at every 1000mm c/c} and Gypserra™Ceiling Angle is fixed at every 900mm along the length of
Intermediate channel with M6 x 12mm Hex Bolt & Nut arrangement material–As per EN 10083 Finish – Zinc Plating} or with
2 Nos of Ø4.2x13 Gyproc® metal to metal screw {Material-Carbon steel EN-ISO 7049/50 Finish- Zinc Coating Thickness-
4.14micron.}. 80x26x0.5mm Gypserra™Ceiling Section {Material-GI (IS513),YS-260Mpa,Finish-Galvanised
150GSM(IS277)} is then fixed to the Gypserra™ Intermediate Channel {Material-GI(IS513),YS-260Mpa, Finish-
Galvanised 150GSM(IS277)} with the help of Gyproc® Connecting Clip {Material -High carbon spring steel
wire(BS970Gr.En42),46-48HRC,Finish-Zinc plating 4-6 micron} and in direction perpendicular to the Intermediate channel at
333mm c/c. Boarding shall start from the center of ceiling area. Single layer 12.5mm Gyproc Rigitone Activ’Air 8/18 board of
size 188x1998mm having all four square edges, 15.5% perforation area of board & hole size of 8mm diameter at a
c/c of 18mm; backed with acoustic tissue, having NRC values 0.55, is then screw fixed to ceiling section with 30mm
Rigitone screws/25mm drywall screws {Material-Carbon steel EN-ISO 7049/50,Finish-Case hardened Grey Phosphating} at
170mm centres. For higher NRC value, Resin bonded glass wool of 24kg/M3 and 50mm thick can be placed on top of
the board ( Refer Rigitone Activ’Air 8/18- PDS for the NRC values). Finally all square edges of the boards are to be jointed and
finished so as to have a flush look. The joint filling using Vario joint filler and Rigitone joint filler set technique should
be employed for the joint-less installation of Rigitone perforated boards with continuous Perforation. After installation
and joint-filling, the boards should be primed and then painted with a short haired paint roller. Paint should not be applied
using a brush or spray diffuser . Serrated steel section has effective thickness of 2T (2xdepth), better load carrying capacity,
enhanced screw retention, Improved acoustic performance & fire resistance as compared to plain steel section. Complete
the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
200 2000 400000
8 Providing & Fixing of Armstrong GI Lay in Standard Perforated (2.5mm diameter-16% open area) metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color with Soundtex acoustical
fleece hot pressed to the back of the perforated tile to be laid on Armstrong grid systems with 24mm wide T - section flanges
color white having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees.
The tiles would have NRC of 0.70, Fire Performance of Class A2-s1.d0 as per EN13501 standard in module size of 600 X 600
mm suitable for Green Building application, with Recycled content of 25%.
The grid should be of “Armstrong” make with 15mm wide T - section flanges color white having rotary stitching on all T
sections i.e. the Main Runner with C3 coupling, 1200 mm & 600 mm Cross Tees with Hardened XL2 Clip having a web height
of 32 mm and a load carrying capacity of 14 Kgs/M. The T Sections have a Galvanizing of 90 grams per M2 with pull out
strength of 100 Kgs. Suspension system for Armstrong grid to be of Armstrong make.
The Tile & Grid system used together should carry a 10 year warrantee.
INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using Armstrong
suspension system (specifications below) at 1200mm maximum centre. The First/Last Armstrong suspension system at the
end of each main runner should not be greater than 450mm from the adjacent wall.
Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm
module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting
600mm long flush fitting cross tees centrally between the 1200 mm cross tees.
Perimeter trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres.
ARMSTRONG SUSPENSION SYSTEM accessories manufactured and supplied by Armstrong World Industries consisting of M6
Anchor Fasteners with Vertical Hangers made of Galvanised steel of size 26 x 26 x 25 x 1.2mm with a Galvanised Thickness of
80gsm, A pre Straightened Hanger wire of dia – 2.65 mm of 1.8 m length., thickness of 80gsm and a tensile strength of 344-
413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanised spring steel for 2.68 mm. The adjustable clip also
consists of a 3.5 mm aquiline wire to be used with the main runner.
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
SMT 30 2600 78000
9 P/F 75 mm high Axiom with Accessories. Complete the work as per site conditions and instructions of Architect,
SBI/SBIIMS engineer.
RMT 90 950 85500
TOTAL OF PAINTING , CEILING & POP WORKS 839500
I Repairs to roof and windows.
1 To providing & fixing in position RINAC PUF sheets having 0.50 mm thick Pre Painted Galavalume sheets on top
and bottom and sandwiched with 30 mm thick PUF of 40 kg/m3 density and fixed with necessary self taping
screws, sealant tapes . With 200 mm end laps and 1 corrugation side lap.The rate is inclusive of removing of
damaged sheet and handed over to the Bank. Complete the work as per site conditions and instructions of
Architect, SBI/SBIIMS engineer.
SMT 50 1850 92500
2 P/FAdditional MS support in MS angle/ channel/ I B eam etc. to be provided to support the new ducting as per
detailed drawing shared by architects. (As existing roof has in polycrbonate sheet, for sefety purpose required
addisional support.) Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
KG 500 100 50000
KUBIK Full Height Glazed Double Glass Partition ( Duoline 100 )
Supply & Installation Modular Aluminium Double glazed partitioning frame of Kubik make 100mm System with
folowwing specifications
Using KOPS-012A & KOPS 010 (100mm x 25mm) as top channel, wall starter,
Using KOPS 041, KOPS 041A & KOPS 010 (100mm x 25mm)As bottom channel.
Partition Dimension – 100mm x 25mm.
Finish – SILVER anodized finish.
glass to glass butt joint with I Joint
5+5+0.76mm thk Laminated Glass
Partition Height : H-2700 MM
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.KUBIK Single leaf Stile 87 - Double Glazed door frame (Duoline -100mm)
Door Opening Size : W 9000mm X H 2700mm
Supply and Installation of Modular Aluminium Single leaf stile door frame of Kubik make 100mm System,
Using KOPS-DF-203 ( 100mm x 25mm) for Stile door frame
Door Frame Dimension – 100mm x 25mm.
Using KOPS-DF-115, KOPS-DF-116, KOPS DF 117 And KOPS-DF-117A for Stile door Shutter
Door Shutter Dimension - 87mm X 45mm.
Finish – SILVER anodized finish.
glass to glass butt joint with I Joint
5mm thk + 5mm thk clear thoughened Glass for gasket reference
Hardware make considered by KUBIK & GEZE :-
KUBIK Flush Hinges
GEZE Concealed Door closer With Hold open
GEZE Mortise Lock with Lever Handle
KUBIK Drop dowen Seal
KUBIK Door Stopper
All hardware are in Reguler finish
Complete the work as per site conditions and instructions of Architect, SBI/SBIIMS engineer.
Total for Repairs to roof and windows. 1035900
Sub TOTAL OF CIVIL& INTERIOR WORKS 6839750
4
3 SMT 60 10600 636000
Nos 2 128700 257400
Sr.
no.
Description of Item Unit Quantity Rate Amount
P & F MODULAR TABLES (1350 X 750MMX 750MM HT) WITH SIDE UNIT FOR AGM
Providing and fixing Modular Table for AGM's, the Top to be made out of 25mm Thick MDF with 1MM thick
approved make laminated & bottom of table shall be finished with 0.8 mm thick laminate in White balancing
having water fall edges. The top is connected with MS powder coated under structure with powder coated
finished legs and modesty panel by means of standard knockdown fittings. Table Modesty Panel are made from
18mm thick pre-laminated MDF with all edge lipped with 0.8mm thick PVC edging. Side unit to be made out of
18 mm thk MDF finished with laminate internally and externally, with approved locking system etc.. All complete
with keyboard/ CPU trolley, cable manager etc. as per Architect instruction and 3d views.
Nos. 3 30000 90000
P & F Deskbase system - Linear workstations (1050 x 500 mmx750mm Ht.) with pedestal-SOC ROOM Nos 68 12000 816000
Providng and fixing Deskbase System - Linear Workstationswith pedestal, the Table Top are made from 25mm
Thick MDF with 1MM thick approved laminated & White balancing in bottom having water fall edges. The top is
connected with the leg and modesty panel by means of standard knockdown fittings. Table top to have a "D"
shape cut out and providing the same with flip box. Table to have MS powder coated finish legs with modesty as
per design and specifications. All complete with keyboard/ CPU trolley and pedestal. All tables to be provided
with plastic headed leveling bolts of M6 mm size to take care of any variations in floor level. 450 mm ht
Magnetic lacquared glass panels from table top to be fixed with studs for sturdyness as per details includng side
divider glass panel in between 2 workstation and end of table. all complete as per approved detailed drawings.
Table to have hanging metal raceway cum modesty panel below table and metal cable riser as per detailed
drawing. Complete the work as per site condition and instruction of Architect, SBI/SBIIMS Engineer.
2a Do as above item no. 2, but P & F Deskbase system Same as above - 900 x 500 mm with sharing pedestal Nos 4 10000 40000
3 DGM Table - 1800 x 900x 750 mm along with Side running storage in Veneer finish -
Providing and fixing Table with side storage unit for DGM to be made out of 19mm Thick ply confirming to IS 303
BWR the all exposed area to be finished with 4mm thk veneer of approved make and colour with PU lamination
polish of approved make. The internal/nonexposible area shall be finished with 1MM thick approved make
laminate. the rate inclusive of providing approved locking system, handle etc. complete with approved keyboard/
CPU trolley, cable manager etc. as per as per site condition and instruction of Architect, SBI/SBIIMS Engineer and
detailed drawing provided by The Architect. Basic rate of Veneer - 120 /-
No. 1 80000 80000
Low Height Storage Veneer Finish in DGM Cabin
P & F Storage 400 mm deep as per required height made out of 18mm thk ply and finished in 4 mm thk. veneer
with PU lamination polish of approved make . As shown in dwg. and 3d view cost to be including with necessary
hardware and fittings Basic rate of Veneer - 120 /-
Low Height & Full Storage Laminate Finish
Providing and fixing 750mm/1200mm/2100 mm high low & Full height storages of 400mm deep in 19mm thk
MDF with 25mm thick MDF Top and 19mm thick MDF Shutters, mounted on auto closing hinges, finished in
1.5mm thick approved shade laminate on all exposed surfaces and Prelaminated internally, incl of intermediate
shelf as per the drawing in 19mm Both side prelam MDF with lipping patti finished in same shade laminate on
both sides, 100mm skirting finished in same shade laminate. Rate to include of necessary nos of approved make
locks, handles, magnetic ball-catch to be fixed in individual units.
Make - Godrej /Featherlite/HNI/ or equivalent
TOTAL 1326000
Sr.
No.
Description of Item Unit Quantity Rate Amount
Providing, Fixing, Installing & putting in place & in proper condition, as per layout & as per direction of the
Engineer in charge. As per following details.
SEAT / BACK ASSY: The seat is made up of 1.4 +/- 0.1 cm thick hot pressed plywood upholstered with fabric and
moulded polyurethane foam. seat size is 49.5 cm (W) x 510.8 cm (D). The Back is injection moulded in Glass filled
polyproptlene which is upholstered with mesh fabric. The Back consist of Adjustable Lumbar support made of
injection moulded Polypropylene having an adjustment of 5.0 +/- 0.1 cm. Back size is 44.5 cm (W) x 57.5 cm (H).
The Polyurethane foam for seat is of density = 30 +/- 2 kg/m3.
Armrest : The height adjustable armrest is made of polypropylene and can be adjusted to 6.0 +/- 0.1 cm height. It
also has swivel and To and Fro adjusment with moulded PU armtop. The mechanism is designed with the
following features:
360O Revolving type, Centr Tilt Synchro. 4 position (including upright lock) giving option of variable tilt angle to
the chair.
Mid Back Chair
Note; Images are for indecative purpose only. Prior approval should be taken from Architect and User department.
1
4
5 SFT
II) MODULAR FURNITURE WORK
40 1500 60000
200
2
III) Supply of Chairs
1 504000600084Nos
1200 240000
SFT
Pneumatic Ht, Adjustment The pneumatic height adjustment has an adjustment stroke of 10.0+/-0.3 cm,
The pedestal is injection moulded Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0+/-0.5 cm.
pitch center dia. The twin wheel castors are injection moulded in black Polypropylene having 5.0 +/- 0.1cm wheel
diameter.
The product to be tested and passed the quality standards as laid down under ISO 9001, 1S014001, ISO 18001,
OHSAS and BIFMA certifications for quality assurance. LOCATION - DGM CABIN & WHEREVER REQUIRED, (
MODEL -GRETA MID BACK of Godrej Brand. )
High Back Chair
Sr.
No.
Description of Item Unit Quantity Rate Amount
1 WAITING LOUNG CHAIR Basic Rate - 15000/- Nos. 4 16500 66000
2 WAVE Coffee table Basic Rate- 5000/- Nos. 2 6000 12000
3 Puffy , Basic Rate- 5000/- Nos. 10 6000 60000
4 GOSSIP - White top Basic Rate- 3000/- Nos. 2 4000 8000
146000
Sr.
No.
Specification Unit Quantity Rate Amount
Carpet Flooring -Tile form Basic Rate -1725/- per sq.mtr.
Style- T653 “Suburb” Carpet Tile
Construction-Hi/Mid/Lo Loop
Pile Fibre-nexlon™ with Tuntex Approved Nylon with Stain Resist Technology
Tufted Machine Gauge- 1/12 gauge
Pile Weight-18 Oz / Sq. Yd.
Pile Height - 5.0/4.0/3.0 mm
Total Thickness -8.2 mm max
Tile size-609mm x 609mm
Total Weight -4900 gm/m2
Wear Warranty-Lifetime – product is warranted not to lose more than 10% pile fibre by weight in normal
commercial use
Colour Fastness-15 Year Warranty ASTM 16-04. Grade 4 – Little or no change
Static Electricity -Permanent Lifetime Protection – less than 3.5kv
Stain Shield -nexlon™ Lifetime Stain Release System
Note; Images are for indecative purpose only. Prior approval should be taken from Architect and User department.
2
1 5500002000275SMTR
1200012000
IV) Loose Furniture
V) CARPET FLOORING WORK
1Nos
Flammability- ASTM E-648 Radiant Panel Class 1
Dimensional Stability -Warranted not to change in size by more than 0.5mm in normal use. Will not dome or dish
in normal use
Installation - Pressure Sensitive Adhesive
Sustainability - All yarns used are Solution dyed to minimise use of water and exclude any effluent production.
CRI Green Label Certification.
ISO 14001 and ISO 9001
ASSUMPTION
INTERNAL TOILET DRAINAGE & WATER SUPPLY WORKS INCLUDED IN THIS BOQ.
SANITARY C.P FITTING & FIXTURE INSTALLATION WORK ONLY INCLUDED IN THIS BOQ.
EXCLUSION
SUPPLY OF WC, WASH BASINS, URINALS, URINALS SENSORS, ALL TAPS / COCKS, HEALTH FAUCETS, FLUSH
VALVES, CP. ANGLE VALVES, FLEXI. 450 mm LONG PIPE ARE NOT CONSIDERED IN THIS BOQ.
TOILET PAPER HOLDER, HAND DRIERS, C.P. CURTAIN ROD, TOWEL ROD, SOAP DISPENSER, NAPKIN RING, WATER
PURIFIER ARE NOT CONSIDERED IN THIS BOQ
FINISHING OF WALLS, INCLUDING TILES etc. ARE NOT CONSIDERED IN THIS BOQ.
DUCTS DRAINAGE LINE FOR SOIL WASTE , RWP, VENT, WATER SUPPLY NOT CONSIDERED IN BOQ.
PRV - PRESSURE REGULATING VALVE FOR FLOOR TAPING NOT CONSIDERED (ASSUMING IT IS PROVIDED BY
BUILDER)
HOT WATER SUPPLY PROVISION NOT CONSIDERED SINCE ITS OFFICE PREMISES.
MAKING OF LEDGE WALL etc CIVIL WORK NOT CONSIDERED IN THIS BOQ
Sr.
No.
Description of Item Unit Quantity Rate Amount
PART A - SANITARY FIXTURES AND CP FITTINGS
1 Providing &Fixing inclusive of testing and commissioning of Wall mounted European water closet (constellation
with ' P' trap), Mounting arrangement with CP bolts / nuts and with Concealed dual flush tank of 3/6 lit. Capacity
with fittings, 32 mm dia CP long flush bend etc., 15mm dia CP angle stop cock with wall flange, 15mm dia and 600
mm long PVC connection pipe, solid plastic seat with cover and lid with heavy duty CP brass hinges and rubber
buffers and flap etc. with all necessary fittings. The work shall include cutting and making good the walls & floors
etc. as per the technical specification and drawings. Note: The rates quoted shall include cost of necessary
consumables like brass screws, white cement, sealants etc. Complete the work as per site conditions, instructions
of Architect, SBI/SBIIMS Engineer incharge
Nos. 4 25000 100000
2 Providing & Fixing inclusive testing and commissioning conforming to I.S 2556 of oval / Circular /square/ rect.
shape counter top / bottom wash basin installed on Granite finished counter and CI brackets, 15mm wall
mounted pillar cock with electric / battery operated sensor, 32 mm dia CP waste coupling, 32 mm dia CP brass
bottle trap with extension piece with all necessary fittings as per the Technical specification and drawings . The
works shall include cutting and making good the walls & floors. (Counter cost for wash basin not considered).
Nos. 8 7200 57600
3 Providing & Fixing inclusive testing and commissioning of flat back lipped urinals - sensor operated conforming to
IS 2556 of suitable size , with electric operated sensor, solenoid valve etc. including CP flush pipe with CP
spreaders, 32 mm dia CP bottle trap with extension piece,32 mm dia CP waste coupling half threaded, etc. with
all necessary fittings. The urinal shall be fixed with hangers and brackets, CP wall flanges if required, complete
including cutting & making good the walls & floors as per the technical specification and drawings.
Nos. 3 9000 27000
Fixing, testing and commissioning of CP health faucet consisting of:
15mm dia C.P. Two way Bib cock
PVC flexible tube of 1.0m length.
Hand operated spray unit (instant type)
CP Crutch
Notes: Conditions mentioned in item no.1 shall be applicable)
PART B - COLD WATER SUPPLY
INTERNAL WATER SUPPPLY WITHIN THE TOILET
Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11
(operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 15mm to 50mm. Schedule 40 for
pipes from 65mm to 150mm. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers,
Unions, reducers, bushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. brass
adaptors (both Male & Female threaded) conforming to ASTM D-2846, ASTM F441 with only CPVC solvent
cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination
fittings. Installation shall be to as per technical manual of manufacturer of pipes & fittings. (For internal water
supply within the toilets)
Note : The work shall include cutting, jointing with solvent cement, pressure testing the joints / pipeline for 10
kg/sq.cm hydraulic pressure, for 5 hours etc., including fixing the pipe with support clamps at 0.9 m spacing,
chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in
walls, making good the walls and bores in CC or CM 1:3 as applicable over the wire mesh as directed by the
Engineer in-charge, clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good
the walls and floors.
Internal Water supply Concealed Pipes for Flushing & Domestic
15 mm dia
Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11
(operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 15mm to 50mm. Schedule 40 for
pipes from 65mm to 150mm. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers,
Unions, reducers, bushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. brass
adaptors (both Male & Female threaded) conforming to ASTM D-2846, ASTM F441 with only CPVC solvent
cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination
fittings. Installation shall be to as per technical manual of manufacturer of pipes & fittings. (For internal water
supply within the toilets)
1 30000600Mtrs. 50
2
4 800020004Nos.
1 5500002000275SMTR
VI) Plumbing Work
Note : The work shall include cutting, jointing with solvent cement, pressure testing the joints / pipeline for 10
kg/sq.cm hydraulic pressure, for 5 hours etc., including fixing the pipe with clevis hanger support at 1.0 m
spacing.
Internal Water supply Pipes above false ceiling for Flushing & Domestic
15 mm dia Mtrs. 50 725 36250
20 mm dia Mtrs. 35 825 28875
25 mm dia Mtrs. 20 925 18500
32 mm dia Mtrs. 15 1125 16875
Supply, Installation, testing and commissioning in position approved make full way lever operated GM ball valves
screw/flange end tested to 16 PN conforming to IS 778 class 1 with all necessary fittings etc., complete. ( for
Domestic & Flushing Water inlet tapping)
15 mm dia Nos. 3 1750 5250
20 mm dia Nos. 2 2450 4900
25 mm dia Nos. 3 2800 8400
PART C - SOIL, WASTE (INTERNAL DRAINAGE SYSTEM)
Supply, Installation , testing & commissioning of UPVC-SWR ( B class ) pipes conforming 'to IS 13592/92 and
fittings conforming to IS-with Fittings - IS 14735, cutting the pipes to required lengths, Installation in position to
required grade and level, jointing, making holes, pockets, chases in walls, floors of all types and making good the
same, testing and rectifying leakages for concealed piping within toilet blocks / kitchen , sunken slab, plinth etc.
complete including all necessary fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls,
offsets, access pipes, rubber rings, jointing with solvent cement followed by application of leak proof adhesive
like FRP paste & laid on floors all complete as per Technical specifications and drawing inside the toilets / pantry.
Notes: Rate Quoted shall be inclusive of cost of other consumables like hacksaw blade solvent cement etc.
80mm dia Mtrs. 20 1760 35200
110mm dia Mtrs. 10 2000 20000
Providing and fixing UPVC pipes pressure rated 6 kg/ sq.cm conforming 'to IS 4985:2000 & Moulded fittings are
manufactured as per IS 7834 and fabricated fittings are manufactured as per IS 10124 for drains including
providing and fixing necessary fittings such as elbows, tees union fittings etc. including cutting holes and
pockets chasing in the wall or floors as required and making good the same to original conditions after
concealing the pipes where required, lagging the concealed pipes with hessian cloth dipped in hot black
bitumen, testing, all complete as per technical specifications and drawing of the following diameters. (for Sink
Drains, Urinals, WB drains pipe )
40mm dia (6kg / sq.cm pr. Rated) SINK & WASH BASIN DRAIN Mtrs. 25 830 20750
50mm dia (6kg / sq.cm pr. Rated) - URINALS Mtrs. 15 910 13650
supply installation, testing and commissioning of PVC Multi Inlet Floor Trap of self cleansing design moulded or
fabricated, if not available in size mentioned below with S.S. grating, with or without vent arm jointing with
rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste including making good
the floors etc. all complete as per technical specifications and drawing.
Size 110 x 75mm. - With SS Grating Nos. 4 2100 8400
Size 110 x 75mm. - Plain cover (For Urinal trap) Nos. 2 1800 3600
For Plumbing Work 443250
I) Interior & Furnishing work
II) MODULAR FURNITURE WORK
III) Supply of Chairs
IV) Loose Furniture
V) CARPET FLOORING WORK
VI) Plumbing Work
Summary for Civil Works
Sr.
No.
Description of Item Unit Quantity Rate Amount
A PANEL & DBs
1 Floor/wall mounted cubicle type panel, Fabricated from 14/16G CRCA sheet steel ,Totally compartmentalized, 7
tank powder coating treatment for rust proofing, with separate busbar chamber & cable chambers ,Front /Back
access for switchgears, connectors etc.Suitable for 430 V, 3 phase / 4 Wire System , 50 Hz supply,50 Deg Celcius
ambient temp,Class 1 Type with 15VA burden, Provisionn for control wiring diagram, 3 MM openable gland plate
on top and bottom of panel, 75 MM height channel base frame to panel. Proper labelling shall be done all
chambers of panel showing feeder rating and location. Testing and inspectionof the panels will be done by the
contractor. The Panel shall be manufactured as per IEC 60204-1
Make: CPRI Approved With ISO certification
1.1 Supply, Installation, Testing & Commissioning of Main LT Panel
Incomer: - 200A 16KA, 4P MCCB- 1 no.
Outgoing: -
100A 4P 16KA, MCCB: - 1 No.
80A 4P, 16KA, MCCB: - 1 No.
63A 4P, 10KA, MCB: - 2 Nos.
32A 4P, 10KA, MCB: - 1 No.
25A 4P, 10KA, MCB: - 1 No
20A 2P, 10KA, MCB: - 2 Nos.
Nos. 1 80000 80000
0
1326000.00
6839750
Summary for Civil Works
2
ELECTRICAL WORK
3
1
2
3
9821000
443250.00
550000.00
146000.00
516000.00
1.2 Supply, Installation, Testing & Commissioning of HVAC Panel.
Incoming
80A 4P, 16KA, MCCB: - 1 No.
Outgoing: -
63A 4P, MCB: - 1 No.
40A 4P MCB: - 3 No's
20A SP MCB: - 3 No's
Nos. 1 50000 50000
2 Supply, Installation, Testing & Commissioning of Following MCCB with CBCT & EFR with all standard accessories in
MS fabricated enclosure. It should have termination box of appropriate size to termiantion of requires cables on
both the sides.
2.1 Supply, installation, testing & commissioning of 63A FP MCB in Metal box. Nos. 1 3600 3600
2.2 Supply, installation, testing & commissioning of 40 A FP MCB in Metal box. Nos. 1 2400 2400
3 Supply, Installation, Testing & Commissioning of Distribution Boards complete with MCBs/ Isolators / Bus bars
and interconnections. No fabricated DBs shall be allowed. Only DBs of specified makes as per list of materials
shall be used all MCB 10 kA. (All DB will have MCB numbering, DB chart, DB number), DB should be fixed with
Anchor fastner to wall with proper GI L angle fixed to wall. Proper earthing should be provided to DB body at 2
places.Cable tray , raceway used for DB drop,shall be earhed to DB earthing with 12 SWG CU wire and lugs with
i) Copper busbars together with tapped neutral bar for individual phases.
ii) Copper earth strip
iii) Interconnections and earthing.
iv) Sheet steel enclosure suitable for recessed or surface mounting with hinged lockable doors.
v) Phase to phase isolation (PPI) in case of 3Ph boards.
vi) Necessary support frame & painting, labeling, phase indicating lamps with fuses etc. complete.
vi) Brass glands for sending and receiving ends suitable for cable sizes mentioned in SLD.
(Crimping lugs forming part of the termination)
Make: Legrand / L&T / Hager / Schneider / IndoAsian
3.1 12WAY PPI TPN (RPDB 1)- Wall mounted MCB double door DBs,fabricated from 16/18 G CRCA sheet steel
with powder coated, and all fixing hardware. DB size should be suitable for Below mentioned MCB
combination
Make: Legrand / L&T / Hager / Schneider / IndoAsian
Nos. 1 15045 15045
Incomer 80A MCB -10KA 4P :- 1 No.
40A 2P, 100mA, RCCB: - 3 No's
Outgoing- 16A SP 'C' CURVE MCB- 30nos
3.2 12WAY PPI TPN as follows (UPS DB)- Wall mounted MCB double door DBs,fabricated from 16/18 G
CRCA sheet steel with powder coated, and all fixing hardware. DB size should be suitable for Below
mentioned MCB combination
Make: Legrand / L&T / Hager / Schneider / IndoAsian
Nos. 1 20800.5 20800.5
Incomer 100A FP,16KA 'D' - CURVE MCCB- 1 No.
Sub Incomer for each phase 80A DP RCCB with 100 mA tripping current : - 3 No's
Outgoing 16A SP MCBs 30 Nos,MCB'S ARE D - CURVE: - 30 No's
3.3 8WAY PPI TPN as follows (RPDB 2)- Wall mounted MCB double door DBs,fabricated from 16/18 G CRCA
sheet steel with powder coated, and all fixing hardware. DB size should be suitable for Below mentioned
MCB combination.
Make: Legrand / L&T / Hager / Schneider / IndoAsian
Nos. 1 10999.9 10999.9
Incomer 32 A FP C - CURVE MCB- 1 No.
Sub Incomer for each phase 25A DP RCCB with 100 mA tripping current: - 3 Nos.
Outgoing 16A SP C Curve MCB - 18 Nos.
3.4 8WAY PPI TPN as follows (LDB)- Wall mounted MCB double door DBs,fabricated from 16/18 G CRCA
sheet steel with powder coated, and all fixing hardware. DB size should be suitable for Below mentioned
MCB combination.
Make: Legrand / L&T / Hager / Schneider / IndoAsian
Nos. 1 10434.7 10434.7
Incomer 32 A FP C - CURVE MCB- 1 No
Sub Incomer for each phase 20A DP RCCB with 100 mA tripping current: - 3 Nos.
Outgoing 10A SP C - CURVE MCB- 18 Nos.
3.5 8WAY SPN as follows (EMDB)- Wall mounted MCB double door DBs,fabricated from 16/18 G CRCA sheet
steel with powder coated, and all fixing hardware. DB size should be suitable for Below mentioned MCB
combination.
Make: Legrand / L&T / Hager / Schneider / IndoAsian
Nos. 1 1394.5 1394.5
Incomer 20A 2P D - CURVE MCB- 1 No.
Outgoing 10A SP D- CURVE MCB - 06Nos.
3.6 MCCB
100 A 4P 16KA MCCB with RHOM with enclosure Nos. 2 4720 11328
A TOTAL 206002.6
B CABLE & WIRING
Supply, testing, tagging, laying & commissioning of following sizes of 1.1 KV grade PVC / XLPE core insulated,
extruded PVC inner sheath, armoured / unarmoured extruded outer sheath FRLS PVC, Copper / Aluminium
conductor cables as per IS 7098 Part I laid over MS supports, cable racks, trenches, or fixing on walls including
clamping the cable to supports in an approved manner along with cable.
Make: RR Kabel, Polycab, KEI
1 SITC of Aluminum / Copper armoured XLPE ,FRLS Grade PVC Insulated cables as per IS 1554 to be fixed to
walls, ceilings, on trays with suitable GI clamp, cable tie at every 450 mm or to be laid in ready-made trench
. Cable tagging shall be done at both the ends of cable.
Make: RR Kabel, Polycab, KEI
1.1 3.5 Core 95 sq. mm. A2XFY. MTR. 50 480 24000
1.2 3.5 Core 35 sq. mm. A2XFY. MTR. 20 180 3600
1.3 4 Core 25 sq. mm. Cu XLPE Cable MTR. 10 1130 11300
1.4 4 Core 10 sq. mm. Cu XLPE Cable MTR. 10 500 5000
1.5 4 Core 4sq. mm Cu XLPE Cable MTR. 10 250 2500
1.6 3 Core 4sq. mm Cu XLPE Cable MTR. 10 210 2100
1.7 3 Core 2.5sq. mm Cu XLPE Cable MTR.
2 SITC of cables with Heavy duty Alu/ Cu. Lugs & Brass cable glands. All Cable should be Double compression gland
for 16 Sqmm and Above cables.The glands should be earthed along with brass clips for Earthing.Bimetallic
washers shall be utilise for Aluminium / COPPER cables for terminations.
Make:BRACO, DOWELLS,COMET
2.1 3.5 Core 95 sq. mm. A2XFY. Nos. 2 500 1000
2.2 3.5 Core 35 sq. mm. A2XFY. Nos. 4 450 1800
2.3 4 Core 25 sq. mm. Cu XLPE Cable Nos. 8 700 5600
2.4 4 Core 10 sq. mm. Cu XLPE Cable Nos. 2 400 800
2.5 4 Core 4sq. mm Cu XLPE Cable Nos. 2 400 800
2.6 3 Core 4sq. mm Cu XLPE Cable Nos. 2 250 500
3 SITC of Light Point wiring through 20/25 mm MS CONDUIT with all required accessories with 2 Nos of 1.5
sqmm & 1 no of 1.5 sqmm ( for earth) PVC insulated Copper FRLS wires with Modular type switches complete
with all accessories as detailed in the specifications. The switch boxes shall be flush mounted with partition /walls
works or as directed by the consultants and shall be done in co-ordination with furniture works. The rate shall
include circuit wiring From LDB to Switchboard Box & Switchboard Box to Switchboard . 2 Nos of 1.5 sqmm & 1
no of 1.5 sqmm ( for earth) Copper conductor PVC insulated FRLS Wire , conduit, back box, switch plate and
modular type switch . Conduit shall be fixed on wall / trays or ceiling with spacers & saddles. The wires will be
terminated in a separate connector before fixtures. All phase neutral and earthing wire shall be terminated in SB
level. No direct looping of Neutral and earthing shall be done. All circuit/ Looping circuits shall have ferrule on
both ends and shall have lugs on both end. Circuit and point wire shall have same colour code. Switch board have
proper stickering showing DB and circuit number. wall chasing and back filling will be in scope of electrical
contractor wherever required.
Make: BEC, AKG, Precision,
Polycab, RR Kabel, Havells
3.1 Electrical Circuit and looping light points (Switch control) 3 x 2.5 Sqmm Cu FRLS PVC insulated wires MTR 2600 28 72800
9.5 Wiring for PIR sensor from cabin SB to sensor and till first light point MTR 300 28 8400
9.6 Primary light points (Switch control) 3 x 2..5 Sqmm Cu FRLS PVC insulated wires for emergency lights MTR 100 28 2800
B TOTAL 143000
C EARTHING :
1 Supply, installation, testing and commissioning of following sizes of GI / Copper strip/wire clamped to walls, cable
trays, in recess or surface etc for panels, DB's equipment / cable System / Lightning protection earthing complete
as required including inter connection between length at joints, all fixing accessories saddles, clamps etc and
other fixing hardware material as required for proper installation as per IS 3043. The Earthing Strip shall be
jointed using two nos. GI / Brass nut bolts with washers etc. on the 6" overlap of the strips near joint.
1.1 GI EARTHING STRIPS 25 x 3MM MTR. 100 131 13100
1.2 GI EARTHING WIRES 8 SWG MTR. 120 121 14520
Same as Above ( For Distribution Boards )
1.3 Supply and laying 1 no. 10 Sq.mm PVC insulated FRLS copper conductor 1100 Volt grade green colour wire using
PVC conduits & accessaries on surface of wall for earthing (Audio Rack & ups EARTHING).
MTR. 40 120 4800
13 SAFE EARTH BOX 25 x 6 MM CU BUSBAR 200MM
Providing and fixing Safe Earth Box 25 x 6 mm copper busbar 300 mm long supported on insulators in M.S powder
coated box of suitable size for connecting various equipments earth wires to main earthing. The front door shall
have acrylic window & box to have 25 mm suitable no. of knock outs.
Nos. 3 2000 6000
14 CU PLATE EARTHING PIT
Supply, installation, testing and commissioning of copper plate earthing stations making earth pits 3.5 mtr deep
with copper earth plate 600 mm x 600 mm x 6 mm thick and B Class GI pipe 1" dia 3.5 mtr length including
funnel, charcoal / coke, salt, all earth work. Providing masonry enclosure 450 x 450 mm with 10 mm thick C.I.
cover plate having locking arrangement and watering pipe, disconnecting / testing links etc as per IS 3043
complete as required for UPS - 2 nos. Sound Rack - 2 nos. & EPBAX - 1 no.
Nos. 4 20000 80000
Note: Cu. Plate and connecting Cu. Strip should be brazed, and SS nut & bolts with washers shall be used for
getting proper connectivity.
C TOTAL 118420
D POWER OUTLETS
1 Supply, Installation , Testing & Commissioning of Point Wiring for RAW power sockets 1 Nos of Universal
sockets 6/16A 3pin & 1 No. controlled by 1 nos 16A switch (for Raw Power)with white plate with 3
core 2.5 sq.mm Cu conductor PVC insulated FRLS wire, Black Colour PVC Sheathed PVC wire in already laid
Raceways/Trunking/Conduits for UPS power points.
8 to 10 Nos of workstations to be looped in one circuit.
1.1 Primary Point ( DB to the First workstation) Nos. 35 1150 40250
1.2 Secondary Loop Points Nos. 140 405 56700
Supply, Installation , Testing & Commissioning of Point Wiring for ups power sockets 1No. of 6A 5 PIN Socket With
6 A Socket in a 3 module box. ( ON UPS Power).with black plate with 3 Nos 2.5 sq.mm. Cu conductor PVC
insulated FRLS wire .The rate shall be inclusive of connecting the switches/sockets & 20/25 mm PVC
Conduit. The rate shall include Power Switch Socket with wiring For Fire /ACCESS Power point
Primary Point ( DB to the First Point) Nos. 35 1150 40250
Secondary Loop Points Nos. 140 405 56700
D TOTAL 193900
E LIGHT FIXTURES
Supply & Installation of the following lighting fixtures with ncessary wall/ ceiling supports, flexible cable drops,
ceiling roses, etc. and testing & commissioning of all lighting fixtures with following features:
8 tank processed CRCA body in powder coated white
High transmittance opal diffuser
LED’s with 50000 burning hrs
High efficiency driver >85%
THD 0.9
>=100lm/w
CRI >80
CCT -5700K ANSI
230V-240V
50Hz
Internal SPD -3KV
Over voltage, open circuit, short circuit protection
440V @ 2HRS , Cut off 320V +/-10%
IP20
1 Supply, Installation, testing & commissioning of 11 W Circular recessed LED downlight Nos. 102 505 51510
2 Installation, testing & commissioning of 12 W Circular recessed LED downlight Nos. 8 675 5400
3 Supply, Installation, testing & commissioning of 30W 4ft. linear LED light Nos. 6 3150 18900
4 Supply, installation, testing & commissioning of 9W LED Strip MTR. 86 45 3870
5 Supply, installation, testing & commissioning of 6W LED Strip MTR. 86 40 3440
E TOTAL 83120
F SWITCH BOARD
1 S/F of 1 Module face plate & conceal box and internal wiring with terminations complete in all respect and
accessories
Nos. 10 295 2950
2 S/F of 2 Module face plate & conceal box and internal wiring with terminations complete in all respect and
accessories
Nos. 2 290 580
3 S/F of 5A modular switch Nos. 14 105 1470
G TOTAL 5000
H LIGHTING SENSOR
1 Supply, installation, testing & commissioning of Occupancy sensor with PIR, ceiling mounting with 180 degree
detection angle, min Range 2 X12 M , upto 8.5 Amps resistive load, time delay in range of (0-59 mins 59
secs),Sensitivity adjustment, IP :20, with options like walkthrough, daylight set point(on/off)
Nos. 2 8325 16650
2 Occupancy sensor with PIR + ultrasonic technology or equivalent , ceiling mounting with 360 degree detection
angle, min Range 8M , upto 8.5 Amps resistive load, time delay in range of (0-59 mins 59 secs),Sensitivity
adjustment, IP :20, with options like walkthrough, daylight set point(on/off) , vacancy,
Nos. 18 6750 121500
H TOTAL 138150
I CURTAIN MOTOR
1 Suuply, installation, testing & commissioning of Cutrain motor with following features:
Input voltage- 100-240V,
Torque- 2N*m
Rated speed- 80-120rpm,
Max. track splice length- 12m
25DB Silent working,
Automation Control- FSK Radio Control without Antenna,
Home Automation control- Dry Cintact Control,
Hand pull start- Hand pull when power off,
Built-in485/232 port,
Syncronized operation,
Adjustable speed,
up or down installation,
Stop by resistance
19 8250 156750
I TOTAL 156750
J RACEWAYS & WIRING
1 Supply and laying Raceways / Conduits ( for under floor trenches / On trays) on existing flooring.
The under floor duct for “in screed” system shall be of “ALU SECTIONS ” 1.6mm Thickness in combination of
single, double or triple runs in compliance with the relevant sections of standard EN 50085 & DIN VDE 0634. The
under floor ALU SECTION ducts shall be of trapezoidal shape for better load withstand capacity and closed box
type construction. The ALU under floor ducts shall have to be provided with required rigidity with a standard
loading capacity of 750N according to VDE 0634 (before screed laying) and shall prevent the seepage of concrete
and screed water. standard length of the duct shall be of 3 mtrs. . Coupler shall be used to connect the standard
lengths of the ducts in screed covered system. Single or multiple runs of ALU ducts need to be secured to the
structural slab by means of fastening clamps. The Alu raceway will be installed under ready made trench.
Make: JINDAL/BHANSALI/MAH EXTRUSION
1.1 250mm x 40mm Aluminium raceways, 1.6 mm thick MTR. 128 288 36864
1.2 150 mm x 40mm Aluminium raceways, 1.6 mm thick MTR. 9 188 1692
1.3 100 mm x 40mm Aluminium raceways, 1.6 mm thick MTR. 140 138 19320
1.4 25mm PVC conduits of wall thickness of 2 mm thick MTR. 75 20 1500
2.1 Supplying and fixing 300/250 mm x 300/250 mm x50mm deep 2 mm thick with GI finish. The junction boxes shall
have knock-outs on all sides suitable for Raceways/conduits. GI Plate The knock out shall be removed at site as
per requirements. (Supplying and fixing of 310 x 310 mm with 2mm thickness S.S. Cover.)
Nos. 11 8380 92180
2.2 Supplying and fixing 200 mm x 200 mm x50mm deep 2 mm thick with GI finish. The junction boxes shall have
knock-outs on all sides suitable for Raceways/conduits. With GI Plate The knock out shall be removed at site as
per requirements.(Supplying and fixing of 210 x 210 mm with 2mm thickness S.S. Cover.)
Nos. 5 6439 32195
2.3 SITC of modular type Under floor modular Junction boxes of 150mm x 150mm x 65mm with double door. Top
cover will be hinged cover with minimum depth of 70 mm with 2nos 15 Amp Swith Socket 2 nos Data Point 2nos
Voice Point Rates are inclusive of Supplying and fixing of 160 x 160 mm with 2mm thickness S.S. Cover.
Nos. 53 4997 264841
J TOTAL 448592
K DATA & VOICE
1 Supply, installation, testing & commisssioning of cat- 6 cable for data points MTR. 5000 41 205000
2 Supply, installation, testing & commisssioning of cat- 6 cable for voice points MTR. 2000 41 82000
3 Supply, installation, testing & commissioning of RJ 45 socket for Data outlet MTR. 167 80 13360
4 Supply, installation, testing & commissioning of RJ 11 socket for Voice outlet MTR. 79 80 6320
K TOTAL 306680
TOTAL 1799614.6
Sr.
No.
Description of Item Unit Quantity Rate Amount
Part -
A
Air Conditioning System - High Side
Each rate quoted shall be inclusive of supply, transportation, handling at site, installation, testing, commissioning
and warranty services, all applicable taxes, duties, octroi etc, conforming to the technical and commercial
conditions.
1 VRF Outdoor Unit (Make - Daikin/Blue Star/ Toshiba/Samsung/LG)
VRF ODU having hermetically sealed Scroll/Twin Rotary type compressors & having all
inverter compressor per module of out door unit, working with refrigerent gas R 410A,
condenser coil fabricated from Seamless Copper tube & Plate type Al. Fins of Multi Row, Axial
Flow, upward throw condenser fan, Condenser fan-motor unit, insulated refrigeration piping,
power / control wiring, and earthing, external wiring between Indoor & Outdoor units and
wiring between HVAC panel to all outdoor units with all system controls.
Each Outdoor units with High Pressure switch, Fan driver overload protector, Over current
relay, Inverter Overload Protector & Fusible Plug. The unit shall be suitable for 415 ± 10 %
volts, 50 Hz, 3 phase AC supply, and IP 55 protection. (contractor to highlight the offered
Compressor configuration in their bid) Unit shall be with anticorosive coating.
Note: Vendor has to submit part load efficiency at the starting of project for Consultant
Approval.
HVAC SYSTEM
1.1 22 HP Capacity VRF ODU Nos. 1 381000 381000
2 Ceiling Mounted Ductable type VRF indoor units (Make - Daikin/Blue Star/ Toshiba/Samsung/LG)
Ceiling Mounted Ductable type VRF indoor units having sound level lower. The unit shall
be insulated with sound absorbing thermal insulation material, Poly-styrene / Polyethylene
foam. The unit shall be supplied with suitable decorative panel & resin net filter with Mold
resistance.
The unit shall be supplied with drain hose, clamp metal, washer fixing plate, sealing pads,
drain pump if required, drain pan, electrical expansion valve, screws, clamps, washer for
hanging bracket & insulation for fitting. (Drain Pump should be included in price) With
remote control.
2.1 8.0 TR Ducted VRF IDU Nos 3 52500 157500
3 Refnet Joints for VRF System (Make - Daikin/Blue Star/ Toshiba/Samsung/LG)
Supply of Imported Branch Distribution Joints / Refnet(Y/T) for VRF system. The Contractor has to
propose the actual quantity required for their specific system design with total required
quantity included under this head.
Note: Vendor has to submit O&EM System Generated Piping Layout.
Nos. 8 3500 28000
4 Central remote controller (VRF BMS) (Make - Daikin/Blue Star/ Toshiba/Samsung/LG)
Supply, Installation, testing & commissioning of Central remote controller(CRC), for centralized controll of whole
VRF system (IDUs as well as ODUs), with on/off controll, operation mode, Set/room temp, filter alarm, thermo
on/off, error code, emergency stop, set temp limit,fan speed/direction etc. It shall have Bac net Communication
protocol to integrate with Plant BMS panel (BMS panel for future)
No 1 30000 30000
5
DX Split - Hi Wall Unit for UPS and Networking Room (Non - VRV System) (Make - Blue Star/Toshiba/ Daikin/
Samsung/LG)
Supply, Installation, testing & commissioning of Hi-Wall Inverter Split units, Air-cooled type complete with the
following components with insulated copper piping from indoor unit to outdoor unit, Minimum 3star rating.
Indoor evaporating unit comprising of cooling coils, insulated drain tray, washable filters, blower, Remote control
with cording, electrical junction box etc. Outdoor condensing unit comprising of Inverter type scroll type
compressor's, copper condenser coils, axial fans pressure switches/cutouts etc. Necessary Refrigerant Gas and
oil charge. Inter-connection of refrigerating piping of copper duly insulated with 19 mm nitrile rubber. Complete
electrical power wiring from HVAC panel to indoor / outdoor units & control wiring of copper required from
indoor and outdoor units. Outdoors unit shall be mounted on painted MS stand.
5.1 2.5 TR Hi-Wall Split Unit with Drain Pump along with Automatic Sequential Timer Included Outdoor Stand Nos 1 86500 86500
Part -
B
Air Conditioning System - Low Side Break Up
1 Refrigerant Copper Piping (Make - Mandev/Rajco/Mexflow)
Supply, Installation, testing & commissioning of Seamless 18 Gauge Copper piping (complying to ASTM
B 280) Suction & Discharge Line of following size duly insulated with 19 mm thickness
(Insulation thickness shall be as per ref. pipe size and company specifications requirement )
Nitrile Rubber Insulation having 0.7 m2.k/W R Value (As per ECBC Requirement)
Refrigeration piping will have to be taken in the piping rack / Support individually connecting
to all indoor units for the respective floors. Even necessary supports, fittings, valves & ref.
joints where ever required will be included. All external ref. pipe insulation shall be coated
with star bond CR 30-36 themal insulation canvass coating.
Note: Vendor has to submit O&EM System Generated Piping Layout.
1.1 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 1 3/8 Inch RMT 22 953 20966
1.2 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 1 1/4 Inch RMT 5 953 4765
1.3 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 1 1/8 Inch RMT 12 953 11436
1.4 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 7/8 Inch RMT 28 800 22400
1.5 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 3/4 Inch RMT 22 800 17600
1.6 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 5/8 Inch RMT 13 647 8411
1.7 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 1/2 Inch RMT 3 647 1941
1.8 Copper Hard Pipe with 19 MM Nitrile Rubber Insulation - 3/8 Inch RMT 18 647 11646
2 Communication Cable (Make - Filonex /Polycab/ RR Cable)
Supply, Installation, testing & commissioning dressing and Terminations of Communication Cable between
Outdoor Units & Indoor Units within rigid PVC conduits.
Note: Vendor has to confirm communication cable size with O&EM.
RMT 120 100 12000
3 Drain Piping (Make - Supreme/Prince/Astral)
UPVC Drain Pipe 6 mm thickness with proper leak proof adhesive at joints, all types of fittings, mounting
materials, clamps & supporting structure, etc.
Note: PVC joining Adhesive having low LOC Contents as per Green Building Guidelines.
Size:
3.1 UPVC Pipe with 9 mm Nitrile Rubber Insulation - 25 MM RMT 36 155 5580
3.2 UPVC Pipe with 9 mm Nitrile Rubber Insulation - 32 MM RMT 20 185 3700
4
Supply, Installation, Testing & Commissioning of additional topping-up of Refrigerant R410a into the system with
proper Std. & precautions.