BILL OF QUANTITIES Baroda Swarojgar Vikas Sansthan · vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

ARCHITECTS:

M/S STHAPATI

ASSOCIATES PVT. LTD.1/24 VIPUL KHAND,

GOMTI NAGAR, LUCKNOW

BILL OF QUANTITIES

Baroda Swarojgar

Vikas Sansthan

OWNER:

Bank Of baroda Zonal OfficeLUCKNOW

Sultanpur, Uttar Pradesh

S. NO. DESCRIPTION OF ITEMCOST (lacs)

A CIVIL

CIVIL

INTERIOR

SUB - TOTAL

B ELECTRICAL

Internal

Date Networking

External

SUB - TOTAL

C PLUMBING

Internal Sanitary

External Sanitary

Rain Water Harvesting

Fire Fighting

Septic Tank & Soak Pit

Boring

SUB - TOTAL

GRAND TOTAL

ABSTRACT OF COST

PROJECT :

BSVS , Sultanpur , UP

Sl.No. Description Unit Qty Rate Rate/Rate In Words Amount

(1) (2) (3) (4) (5)' (6) (7)

EARTH WORK

1 Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains

(exceeding 1.5 m in width or 10 sqm on plan), including

disposal of excavated earth, lead upto 50m and lift upto 1.5

m, disposed earth to be levelled and neatly dressed.

All kinds of soil cum 326.40

2 Filling available excavated earth(excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20

cm in depth consolidating each deposited layer by ramming

and watering, lead up to 50 m and lift upto 1.5 m.

cum 156.00

3 Carriage of Materials by Mechanical Transport including

loading, unloading and stacking

Earth - up to 5km cum 170.40

Beyond 5km up to 10km per km (Rs. 10.85) cum

Beyond 10km up to 20km per km (Rs. 8.91) cum

4 Supplying and filling in plinth with sand under floors

including, watering, ramming consolidating and dressing

complete.

cum 35.70

ATT

5 Along external wall where the apron is not provided using

chemical emulsion @ 7.5 litres / sqm of the vertical surface

of the substructure to a depth of 300 mm including

excavation channel along the wall & rodding etc. complete

With Chlorpyriphos/ Lindane E.C. 20% with 1%

concentration

metre 212.60

6 Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart including

drilling 12 mmdiameter holes and plugging with cement

mortar 1 :2 (1 cement: 2 Coarse sand) to match the existing

floor:2.35.3.1

7 With Chlorpyriphos/Lindane E.C. 20% with

1%concentration chemical emulsion @ 7.5 litres / sqm of the

vertical surface of the substructure to a depth of 300 mm

including excavation channel along the wall & rodding etc.

complete:

sqm 396.00

BOQ/Tender Part-II - BSVS - CIVIL

BOQ For Tender BSVS Page 3


8 Supplying chemical emulsion in sealed containers including

delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 112.00

CONCRETE WORK

9 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone

aggregate 40 mm nominal size)

cum 84

10 Making plinth protection 50 mm thick of cement concrete

1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate

20 mm nominal size) over 75mm bed of dry brick ballast 40

mm nominal size well rammed and consolidated and grouted

with fine sand including finishing the top smooth.

sqm 122.00

DPC

10 Providing and laying damp-proof course 50mm thick with

cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4

graded stone aggregate 20mm nominal size).

sqm 52.00



DESIGN MIX CONCRETE

11 Providing and laying in position machine batched and

machine mixed design mix M-25 grade cement concrete for

reinforced cement concrete work, using cement content as

per approved design mix, including pumping of concrete to

site of laying but excluding the cost of centering, shuttering,

finishing and reinforcement, including admixtures in

recommended proportions as per IS: 9103 to accelerate,

retard setting of concrete, improve workability without

impairing strength and durability as per direction of

Engineer-in-charge.

Note:- Cement content considered in this item is @

330kg/cum. Excess/less cement used as per design mix is

payble/recoverable separately).

All works upto plinth level cum 129.40

All works above plinth level upto floor 2 level cum 245.00

FORM WORK

12 Centering and shuttering including, propping etc and

removal of form for :

Foundations, footings, bases of columns, etc. for mass

concrete

sqm 258.60

Suspended floors, roofs, landings balconies and access

platform

sqm 205.60

Lintels, beams, plinth beams, girders, bressumers and

cantilevers

sqm 808.80

Columns, Pillars, Piers, Abutments, Posts and Struts sqm 207.80

Stairs, (excluding landings) except spiral-staircases. sqm 61.50

STEEL REINFORCEMENT

13 Reinforcement for R.C.C work including straightening,

cutting, beding, placing in position and binding all complete

upto plinth level

Thermo-Mechanically Treated bars of grade Fe-500D or

more

Kg 45485.80



BLOCK WORK

14 Providing and laying autoclaved aerated cement blocks

masonry with 100 mm thick AAC blocks in super structure

above plinth level up to floor V level in cement mortar 1:4 (1

cement : 4 coarse sand ). The rate includes providing and

placing in position 2 Nos 6 mm dia M.S. bars at every third

course of masonry work.

cum 51.60

15 Providing and laying autoclaved aerated cement blocks

masonry with 230 mm thick AAC blocks in super structure

above plinth level up to floor V level with RCC band at sill

level and lintel level with approved block laying polymer

modified adhesive mortar all complete as per direction of

Engineerin- Charge.

cum 364.90

GRANITE WORK

16 Providing and laying Polished Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building, all complete as per the architectural

drawings, with 18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4 coarse sand),

laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade,

including rubbing, curing and polishing etc. all complete as

specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

sqm

17 Providing and fixing 18 mm thick gang saw cut, mirror

polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and

similar locations of required size, approved shade, colour

and texture laid over 20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to give

high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm sqm 15.30

18 Providing edge moulding to 18 mm thick marble stone

counters, Vanities etc., including machine polishing to edge

to give high gloss finish etc. complete as per design

approved by Engineer-in-Charge.Granite work metre 51.60



19 Extra for providing opening of required size & shape for

wash basin/ kitchen sink in kitchen platform, vanity counter

and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges etc. complete.

Each 12.00

20 DOORS/WOOD WORK

a Providing and fixing Pre-laminated flat pressed 3 layer

(medium density) particle board or graded wood particle

board IS : 3087 marked, with one side decorative and other

side balancing lamination Grade I, Type II exterior grade IS :

12823 marked, in shelves with screws and fittings wherever

required, edges to be painted with polyurethane primer

(fittings to be paid separately).

25 mm thick sqm 44.70

21 Providing and fixing angle iron frames for doors, windows

and ventilators of mild steel Angle sections of size 35x35x5

mm, joints mitred and welded by angle iron 35x35x5 mm or

35x 5 mm flat pieces to the existing T-iron frame or to the

wall with dash fastener, including fixing of necessary butt

hinges and screws and applying a priming coat of approved

steel primer, all complete as per the direction of Engineer-In-

charge.

kg 472.80

22 Providing and fixing aluminium extruded section body

tubular type universal hydraulic door closer (having brand

logo with IS : 3564, embossed on the body, door weight

upto 36 kg to 80 kg and door width from 701 mm to 1000

mm), with double speed adjustment with necessary

accessories and screws etc. complete.

Each 26.00

23 Providing and fixing aluminium sliding door bolts ISI

marked anodised (anodic coating not less than grade AC 10

as per IS: 1868) transparent or dyed to required colour or

shade, with nuts and screws etc. complete.300x16 mm Each 26.00

24 Providing and fixing aluminium tower bolts ISI marked

anodised (anodic coating not less than grade AC 10 as per

IS: 1868) transparent or dyed to required colour or shade

with necessary screws etc. complete:

200x10 mm Each 52.00



25 Providing and fixing aluminium handles ISI marked


IS: 1868) transparent or dyed to required colour or shade

with necessary screws etc. complete:

125 mm Each 35.00

100 mm Each 35.00

26 Providing and fixing aluminium hanging floor door stopper

ISI marked anodised (anodic coating not less than grade AC

10 as per IS: 1868) transparent or dyed to required colour

and shade with necessary screws etc. complete.

Twin rubber stopper Each 26.00

27 Providing and fixing bright finished brass 100 mm mortice

latch and lock ISI marked with six levers and a pair of


IS: 1868) aluminium lever handles of approved quality with

necessary screws etc. complete

Each 8.00

28 Providing and fixing 50 cm long aluminium kicking plate of

size 100x3.15 mm, anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or dyed to

required colour or shade, with necessary screws etc.

complete.

Each 20.00

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard

tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing

with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom

and sides with required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight,

mitred and jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing / paneling,

C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-

charge. (Glazing, paneling and dash fasteners to be paid for

separately) :

29 For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision for

fixing of fittings wherever required including the cost of

EPDM rubber / neoprene gasket required (Fittings shall be

paid for separately)



Polyester powder coated aluminium (minimum thickness of

polyester powder coating 50 micron)

kg 1778.90

30 Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural

drawings and the directions of Engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness sqm 17739.00

31 Providing and fixing double action hydraulic floor spring of

approved brand and manufacture conforming to IS : 6315,

having brand logo embossed on the body / plate with double

spring mechanism and door weight upto 125 kg, for doors,

including cost of cutting floors, embedding in floors as

required and making good the same matching to the existing

floor finishing and cover plates with brass pivot and single

piece M.S. sheet outer box with slide plate etc. complete as

per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness Each 0.00

21 GLASS WORK

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including

providing and fixing top & bottom pivot & spring type

fixing arrangement and making necessary holes etc. for

fixing required door fittings, all complete as per direction of

Engineer-in-charge.Polyester powder coated minimum

thickness 50 micron Aluminium tubular handle bar included

with stopper and complete in all respects.

sqm 3.15

FLOORING

22 Kota stone slab flooring over 20 mm (average) thick base

laid over and jointed with grey cement slurry mixed with

pigment to match the shade of the slab, including rubbing

and polishing complete with base of cement mortar 1 : 4 (1

cement : 4 coarse sand) :

25 mm thick sqm 557.70

23 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate) finished with a floating coat of neat

cement, includingcement slurry, but excluding the cost of

nosing of steps etc. complete.



11.3.1 40 mm thick with 20 mm nominal size stone

aggregate

sqm 24.20

24 Kota stone slabs 20 mm thick in risers of steps, skirting,

dado and pillars laid on 12 mm (average) thick cement

mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey

cement slurry mixed with pigment to match the shade of the

slabs, including rubbing and polishing complete.

sqm 313.30

25 Providing and laying Ceramic glazed floor tiles of size

300x300 mm (thickness to be specified by the manufacturer)

of 1st quality conforming to IS : 15622 of approved make in

colours such as White, Ivory, Grey, Fume Red Brown, laid

on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse

sand), jointing with grey cement slurry @ 3.3kg/sqm

including pointing the joints with white cement and

matching pigment etc., complete.

sqm 10.00

26 Chequerred precast cement concrete tiles 22 mm thick in

footpath & courtyard, jointed with neat cement slurry mixed

with pigment to match the shade of tiles, including rubbing

and cleaning etc. complete, on 20mm thick bed of cement

mortar 1:4 (1 cement : 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey

cement

sqm 6.00

FALSE CEILING



27 Providing and fixing ceiling at all height including providing

and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating

of 120 gms/sqm (both side inclusive) as pe IS : 277 and

consisting of angle cleats of size 25mm wide x 1.6 mm thick

with flanges of 27mm and 37mm, at 1200mm centre to

centre, one flange fixed to the ceiling with dash fastener

12.5mm dia x 50mm long with 6mm dia bolts, other flange

of cleat fixed to the angle hangers of 25 x 10 x 0.05mm of

required length with nuts and bolts of required size and other

end of angle hanger fixed with intermediate G.I. channels

45x15x0.9mm running at the spacing of 1200mm centre to

centre, to which the ceiling section 0.5mm thick bottom

wedge of 80mm with tapered flanges of 26mm each having

lips of 10.5mm, at 450mm centre to centre, shall be fixed in

a direction perpendicular to G.I. intermediate channel with

connecting clips made out of 2.64mm dia x 230mm long G.I.

wire at every junction,

including fixing perimeter channels 0.5mm thick 27mm high

having flanges of 20 mm and 30 mm long, the perimeter of

ceiling fixed to wall/partition with the help of rawl plugs at

450mm centre, with 25mm long dry wall screws @ 230mm

interval, including fixing of gypsum board to ceiling section

and perimeter channel with the help of dry wall screws of

size 3.5 x 25mm at 230mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the

board with recommended jinting compound, jointing tapes,

finishing with jointing compound in 3 layers covering upto

150mm on both sides of joint and two coats of primer

suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings,

grills, diffusers, cutouts made with frame of perimeter

channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but

excluding the cost of painting with:

28 12.5 mm thick tapered edge gypsum plain board conforming

to IS: 2095- Part I

sqm 12.00

29 ROOFING



Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of

following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm

of cement admixed with water proofing compound

conforming to IS. 2645 and approved by Engineer-in-charge

over the RCC slab including adjoining walls upto 300 mm

height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick

bats 25 mm to 115 mm size with 50% of cement mortar 1:5

(1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by

Engineer-in-charge over 20 mm thick layer of cement mortar

of mix 1:5 (1 cement :5 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved

by Engineer-in-charge to required slope and treating

similarly the adjoining walls upto 300 mm height including

rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat

of cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge.(d) Finishing the surface with 20 mm thick jointless cement

mortar of mix 1:4 (1 cement :4 coarse sand) admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge including laying glass fibre

cloth of approved quality in top layer of plaster and finally

finishing the surface with trowel with neat cement slurry and

making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water

for a minimum period of two weeks for curing and for final

test. All above operations to be done in order and as directed

and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness

at khurra as 65 mm.

sqm 398.10



Providing and laying water proofing treatment in sunken

portion of WCs, bathroom etc., by applying cement slurry

mixed with waterproofing cement compound consisting of

applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed

with waterproofing cement compound @ 0.253 kg/ sqm.

This layer will beallowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed

withwater proofing cement compound @ 0.126 kg/sqm. This

layerwill be allowed to air cure for 4 hours followed with

water curingfor 48 hours. The rate includes preparation of

surface, treatmentand sealing of all joints, corners, junctions

of pipes and masonrywith polymer mixed slurry.

sqm 133.60

FINISHING

30 12 mm cement plaster finished with a floating coat of neat

cementof mix

1:4 (1 cement: 4 fine sand sqm 1894.70

31 15 mm cement plaster on rough side of single or half brick

wall finished with a floating coat of neat cement of mix :

1:4 (1 cement: 4 fine sand) sqm 2141.00

PAINTING

32 Interior

Distempering with oil bound washable distemper of

approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer.

sqm 1902.00

33 Exterior

Finishing walls with water proofing cement paint of required

shade :

New work (Two or more coats applied @ 3.84 kg/10 sqm) sqm 2141.00

Miscellaneous Building Works

34 Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P.

brass screws and washers complete.

Each 8.00



35 Providing and laying factory made chamfered edge Cement

Concrete paver blocks In foot path, park & lawns driveway

or light & traffic parking etc. of required strength, thickness

& size/ shape, made by table vibratory method using PU

mould, laid in required colour & pattern over 50mm thick

compacted bed of course sand, compacting and proper

embedding/laying of inter locking paver blocks into the sand

bedding layer through vibratory compaction by using plate

vibrator, filling the joints with sand and cutting of paver

blocks as per required size and pattern, finishing and

sweeping extra sand, all complete as per manufacturer's

specifications & direction of Engineerin- Charge.

80mm thick Cement concrete paver block of M-30 grade

with approved colour, design & pattern.

sqm 375.00

35 Providing and laying at or near ground level factory made

kerb stone of M-25 Grade cement concrete in position to the

required line, level and curvature, jointed with cement

mortar 1:3 (1 cement : 3 coarse sand), including making

joints with or without grooves (thickness of joints except at

sharp curve shall not be more than 5mm), including making

drainage opening wherever required complete etc. as per

direction of Engineer-in-charge (length of finished kerb

edging shall be measured for pavement). Precast C.C. kerb

stone shall be approved by Engineer-in-charge).

cum 20.32

Stair Railing

36 Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer using structural steel

etc. as requiredIn gratings, frames, guard bar, ladder, railings, brackets,

gatesand similar works

kg 458.50

GRAND TOTAL of Civil Items



S.No. Description Unit Quantity Rate Rate In Words Amount

37 Supplying and fixing chairs in class room with writing

pad of size (H-840 X W 460 X D400) WITH PU

HANDLE,SEAT & BACK HD FOAM STEEL FRAME PIPE 1

INCH 16 GAUGE Nos. 70

38

Supplying and fixing revolving chair for faculty in class

room of size (965 X 700 X 700) with central tilt,PU

Foam Seat & Back, with gas lift & steel inserted Base. Nos. 2

39

Supply and fixing steel table for faculty in class room

with ONE DRAWER should have 18 mm thick pre lam

TOP SIZE:W-900 X D-600 X H-755 MM Nos. 2

40 Supply and fixing revolving chair for staff in office and

faculty room of Size:(970 X 650 X 580) with Push

Back,PU Foam Seat & Back, with gas lift & steel

inserted Base. Nos. 6

41 Supplying and fixing table for staff in office and faculty

room with MOBILE PEDESTAL which should have 25

mm thick pre lam work top with duck Nose bidding &

16 mm thick Nos. 6

42 Supplying and fixing fixed back chair for visitors in

faculty and staff room made of PU Foam Seat & back

Size: (800 X 610 X 550) Nos. 5

43

Supplying and fixing revolving chair in work shop of

Size:(970 X 650 X 580) with Push Back,PU Foam Seat &

Back, with gas lift & steel inserted Base. Nos. 6

44 Supplying and fixing table in work shop with MOBILE

PEDESTAL which should have 25 mm thick pre lam

work top with duck Nose bidding & 16 mm thick legs

Size (1200 X 900 X 750), Pedestal Size: size (400 X 485

X 665) Nos. 6

45 Supplying and fixing fixed back chair with handle in

computer lab made of PU Foam Seat & back Size: (800

X 610 X 550) Nos. 8

46 Supplying and fixing table in computer lab which

should have 18 mm thick pre lam TOP SIZE:W-900 X

D-590 X H750 MM Nos. 8

BOQ-BSVS-INTERIOR



47 Supplying and fixing fixed back chair with handle in

common room made of HD Foam Seat & back Size:

(880 X 580 X 580) Nos. 8

48 Supply and fixing table in common room which should

have 25 mm thick pre lam work top with duck Nose

bidding & 16 mm thick legs Size(L-1800 X W-1200 X H-

750) Nos. 1

49

Supply and fixing revolving chair in director room of

size (965 X 700 X 700) with central tilt,PU Foam Seat &

Back, with gas lift & steel inserted Base. Nos. 1

50 Supplying and fixing fixed back visitor's chair with

handle in director room made of PU Foam Seat & back

Size: (800 X 610 X 550) Nos. 6

51 Supplying and fixing table in director room with ERU &

MOBILE PEDESTAL which should have 25 mm thick pre

lam work top with duck Nose bidding & 16 mm thick

legs Size (L-1200 X W- 900 X H-750), Pedestal Size:

size (400 X 485 X 665), ERU SIZE: size (1060 X 420 X

690) Nos. 1

52 Supplying and fixing computer table in director room

which should have 18 mm thick pre lam W-1230 X D-

610 X H770 MM Nos. 1

53 Supplying and fixing bunker bed of size 2005 L x 987 W

x 750 H with mattress size 1905 x 915 (75"x36") of

MILD STEEL TUBULAR SECTION Ø 19.05 / R. tube 50.8

x 25.4 / S. Tube 19.05 x 19.05 / 40 x 40 / 20 swg & 21

swg Nos. 18

54 Supplying and fixing dining table made of stainless

steel tubular section of 304 grade with dining table

upto top of 16 to 18 mm thick. Nos. 2



55 Supplying and fixing dining chair made of single piece

moulded plywood 12 mm thick venner faced duly

polished and fixed on base pipe 25 mm dia stainless

steel 16 guage with support and back support of size

420w*480d*980h Nos. 16

56 Supplying and fixing double bed set Constructed in ‘B’

grade Teak wood, Overall size 78” x60”x12” finished in

lacquer polish. Constructed with two 3”X3”X12” posts

with decorative finishon the foot side of the bed and

two posts 3”X3” on the head side of the bed to have

suitable castor wheels with total height of 12”. These

posts must be joined with 72” (finished length) plank

of6”X1”on the long side and 54”net plank on the same

size on the short side of the bed joined in dowels as

shown in the sketch in the right column. The bed to be

covered in 19mm ply board suitably molded in teak

wood to hold the mattress and give finished look.

Nos. 2

57 Supplying and fixing two seater steel bench Nos. 1

58 Supplying and fixing dining set-4 seater in living room

made of sturdy sheesham wood Nos. 1

59 Supplying and fixing dining set-6 seater in living room

of size 450w*560d*890h, dining table sports a

tempered glass and sheesham wood Nos. 1

60 Supplying and fixing glass table of tempered glass and

wooden legs. Nos. 2

61

Supply & fixing of vertical blinds with head rail of

25mm high & 50mm wide extruded alluminium aloy

section with wall thickness of 1.2 mm. The section to

be anodized for smooth and crozen resistent finish

with the provision of fabric valance matching with

louvers fabric. The blinds are to be provided with

complete accessories required for proper functioning

of the system to the satisfaction of the enginer-in-

charge/ Architect. m 60

Grand Total of Interior



I POINT WIRING

62 Wiring for light point/fan point/ exhaust fan/call bell point

with 1.5 sqmm. FR PVC insulated copper conductor single

core cable in Surface/ recessed medium class PVC conduit, ,

with modular switch, modular plate, suitable G.I. box and

earthing the point with 1.5sqmm FR PVC insulated copper

conductor single core cable etc as required. Group C Each 221

63 Wiring for twin control light point with 1.5 sqmm. FR PVC

insulated copper cunductor single core cable in Surface/

recessed medium class PVC conduit, 2 way modular switch,

modular plate, suitable size G.I.box and earthing the point

with 1.5sqmm FR PVC insulated copper conductor single

core cable etc. as required. Each 4

64 Supply and fixing of suitable size GI box with modular plate

and cover in front on surface or in recess, including

providing and fixing 3 pin 5/6 amps. modular socket outlet

and 5/6 amps. modular switch, connection, painting etc. as

required. Each 25

65 Supply and fixing of suitable size GI box with modular plate

and cover in front on surface or in recess, including

providing and fixing 6 pin 15/16 & 5/6 amps. modular

socket outlet and 15/16 amps. modular switch, connection,

painting etc. as required. Each 9

66 Supply and fixing 20 amp, 240 volts, SPN industrial Type,

socket outlet ,With 2 pole and earth ,metal enclosed plug top

along wth 25/32 amp. `C` series SP,MCB , in sheet steel

encosure, on surface or in recess with chained metal cover

for the socket out let and complete with connections, testing

and commissioning etc. as required. Each 21

67 Supply and fixing Two Module stepped type electronic fan

regulator on the existing modular plate switch box

including connections but excluding modular plate etc. as

required. Each 38

BILL OF QUANTITY - BSVS- Internal Electrical

SI.

No. DESCRIPTION UNIT QTY Rate RATE IN WORDS

AMOUNT

(in Rs)



68 Supplying and fixing brass batten holder including

connections etc. as required. Each 14

69 Supplying and fixing call bell/ buzzer suitable for single

phase, 230 volts, complete as required. Each 3

70 Wiring for circuit/sub-main wiring along with earth wire

with the following size of FR PVC insulated copper

conductor, single core cable in surface/ recessed medium

class PVC conduit as required.

2X2.1.5 sqmm + 1x1.5 sqmm earth wire Metre 575

2X2.5 sqmm + 1x 2.5 sqmm earth wire Metre 465

2X4.0 sqmm + 1x 4.0 sqmm earth wire Metre 345

4X6 sqmm + 2x 6.0 sqmm earth wire Metre 125



DISTRIBUTION BOARDS, MCB'S & ISOLATORS :

71 Supplying and fixing following way, single pole and neutral,

steel, MCB distribution board, 240 volts, on surface/

recess,complete with tinned copper bus bar, neutral bus bar,

earth bar,din bar, interconnections, powder painted including

earthing etc.as required. (But without MCB/RCCB/Isolator)

12way , Double door Each 1

72 Supplying and fixing following way, prewired three pole

and neutral MCB distribution board of sheet steel for 415

volts on surface /recess complete with loose wire box,

terminal connection for all incoming and outgoing

circuit,duly prewired with suitable size FR PVC insulated

copper conductor up to terminal block, tinned copper

busbar, neutral link, earth bar, din bar, detachable gland

plate, interconnections, powder painted including earthing

etc. as required (But without MCB / RCCB / Isolators).

4way (4 + 12), Double door Each 5

6way (4 + 18), Double door Each 1

73 Supplying and fixing 5 amps. to 32 amps. rating, 240 volts

`C' series, miniature circuit breaker (MCB) suitable for

inductive load of following poles in the existing MCB

DB complete with connections, testing and commissioning

etc. as required.Single Pole Each 88

Double Pole Each 1



74 Supplying and fixing single pole, blanking plate in the

existing MCB DB complete etc. as required. Each 25

75 Supplying and fixing following rating, four pole, (three

phase and neutral) 415 volts, residual current circuit

breaker (RCCB), having a sensivity current upto 300

miliampere in the existing MCB DB complete with

connections,testing and commissioning etc. as required :

40 Amps Each 4

63 Amps Each 2

TELEPHONE / TELEVISION

76 Supplying and drawing following pair 0.5 sqmm FR PVC

insulated annealed copper conductor, unarmoured telephone

cable in the existing surface/recessed steel/PVC conduit as

required.2 Pair Metre 315

77 Supplying and drawing co-axial TV cable RG-6 graded, 0.7

mm solid copper conductor PE insulated,shielded with fine

tinned copper braid and protected with PVC sheath in the

existing surface/ recessed steel/ PVC conduit as required. Metre 240

78 Supplying and fixing following modular switch/ socket on

the existing modular plate & switch box including

connections but excluding modular plate etc as required.

Telephone socket outlet Each 12

TV antenna socket outlet Each 8

79 Supplying and fixing following size/modules, GI box along

with modular base & cover plate for modular switches in

recess etc as required.1 or 2 Module (75mm X 75 mm) Each 20

80 Supply and fixing of following size of PVC conduit

alongwith the accessories in recess including painting in case

of surface conduit, or cutting the wall and making good the

same in case of recessed conduit as required:

20mm Metre 450

EARTHING



81 Earthing with GI earth pipe, 4.5mtr long, 40mm dia

including accessories and providing masonary enclosure

with cover plate having locking arrangement etc, (with

charcoal and salt ) as required. Set 7

82 Supplying and Laying of 25 mm X5 mm G.I strip at 0.50

metre below ground as strip earth electrode, including

connection / terminating with nut, bolt, spring, washer etc. as

required.( jointing shall be done by overlapping and with 2

sets of G.I. nut bolt & spring washer spaced at 50mm)Meter 75

83 Supplying and Laying of 6 SWG G.I wire at 0.50 metre

below ground level for conductor earth electrode, including

connection / terminating with G.I. thimble etc. as required.Meter 200

INSTALLATION OF LIGHT FIXTURES :

84 Installation, testing and commissioning of wall

bracket/ceiling fitting of all sizes and shapes containing upto

two GLS/CFL/LED Lamps per fitting, complete with all

accessories including connections etc. as required. Each 93

85 Installation, testing and commissioning of prewired,

flourescent fitting / compact fluorescent fitting of all

types, complete with all accessories and tubes etc. directly on

ceiling / wall, including connection with 1.5 sq. mm. PVC

insulated, copper conductor, single core cable etc. as

required. Each 68

INSTALLATION OF FANS AND EXHAUST FANS :

86 Installation, testing and commissioning of ceiling fan

including wiring the down rod of standard length (upto 30

cm.) with 1.5 sq. mm. FR PVC insulated, copper conductor,

single core cable, including providing and fixing phenolic

laminated sheet cover on the fan box etc. as required.

Each 38

87 Installation of exhaust fan p in the existing opening,

including making good the damage, connections, testing,

commissioning etc. as required.

upto 450 mm sweep. Each 7



88 Extra for fixing the louvers / shutters complete with frame

fro exhaust fans of all sizes. Each 7

SUPPLY OF LIGHT FIXTURES :

89 Supply & fixing of single wall bracket suitable for up to 7

watt LED Luminaire complete in all required.

Cat. A Each 8

90 Supply of recess /surface/pendent mounted suitable for 18

watt LED decorative mirror light complete including tube

etc.on surface complete in all respects.Cat. AA Each 10

91 Supply of recess /surface/pendent mounted round 6watt to 8

watt LED down lighter having powder coated die cast

aluminium housing with heat sink, diffuser/reflector with

driver set complete in all respect.Cat. AAA Each 71

92 Supply of LED tube light with batten suitable for up to 20

watt LED tube light complete including tube etc on surface

complete in all respect.Cat. AA Each 54

93 Supply of recess /surface/pendent mounted suitable for up to

34 watt LED Luminaire complete including tube etc on

surface complete in all respect.Cat. AA Each 4

94 Supply and erection of AC 1200mm Sweep, 230/250 Volts,

50 Hz ceilling fan with regulater standar down rod, blades

including connection etc. complete as required Each 30

Make: Havells/CG/Usha/Bajaj/ Equivalent Make

95 Supply and fixing of wall fan (400mm 16") -CG/Usha/Bajaj

& Equivalent make Each 8

96 Supply and erection of AC 230/250 Volts, 375mm sweep, 50

Hz exhaust fans including providing nuts, bolts, mounting

frame and other accessories including connections etc.

complete as required a) Make: Havells/CG/Usha/Bajaj/ Equivalent Make Each 7

97 Supply & fixing of Louvers upto 18". Each 7

98 Supply and fixing of 9 W LED LAMP -CG/Usha/Bajaj &

Equivalent make Each 14



99 Supply and fixing of backelite Fan sheet complete as

required . Each 30

COMPUTER POINTS

100 Supplying and fixing of 1 No. 16 A modular switch and 2

Nos. 6A modular socket & 1 No.16 A modular socket

including metal box (recessed/ surface) Each 13

101 Supply and erection of 1.5 TONE SPLIT AC complete in all

respects Each

102 Supply and erection of AC STABILIZER 150 -290 V

complete in all respects Each

GRAND TOTAL OF INTERNAL ELECTRICAL

TERMINATION OF CABLE :

103 Supplying & making end termination with brass

compression gland and aluminium lugs for the following

size of PVC sheathed / XLPE aluminium conductor cable of

1.1 KV grade as required.2.0 X 10 sqmm. (19mm) Each 6

3.5 X185 sqmm. (57mm) Each 2

4.0 X 10 sqmm. (25mm) Each 16

104 Providing, laying and fixing following dia G.I. pipe (medium

class) in ground complete with G.I. fittings including

trenching (75 cm deep)and re-filling etc as required

50 mm Dia Metre 85

105 Providing, laying and fixing follwing dia RCC pipe NP2

class (light duty) in ground complete with RCC collars,

jointing with cement mortar 1:2 (1 cement : 2 fine sand)

including trenching (75cm deep) and refilling etc as

required.100mm dia Metre 35

150mm dia Metre 35

EARTHING

BILL OF QUANTITY -BSVS-External Electrical

SI.

No. DESCRIPTION UNIT QTY Rate RATE IN WORDS

AMOUNT

(in Rs)



106 Earthing with GI earth pipe, 4.5mtr long, 40mm dia

including accessories and providing masonary enclosure

with cover plate having locking arrangement etc, (with

charcoal and salt ) as required. Set 4

107 Supplying and Laying of 6 SWG G.I wire at 0.50 metre

below ground level for conductor earth electrode, including

connection / terminating with G.I. thimble etc. as required. Meter 250

108 Supplying and Laying of 25 mm X 5 mm G.I strip at 0.50

metre below ground as strip earth electrode, including

connection / terminating with nut, bolt, spring, washer etc. as

required.( jointing shall be done by overlapping and with 2

sets of G.I. nut bolt & spring washer spaced at 50mm)

Meter 100

L.T. CABLES

109 Supply and laying of aluminium conducter, PVC insulated

armoured, served, sheeted cables 1100 bolts grade at a depth

of 750mm below ground level over a cushion of 75mm thick

sand all round and protected with burnt bricks on sides and

on top. on surface, the cable run shall be fixed on M.S.

clamps etc. of suitable size or as directed by the Engineer-

Incharge, complete in all respect. the armouring of the cable

sall be property connected with the earth conductor by

clamps etc.

10 sqmm 2.0core Metre 175



EXTERNAL LIGHT

110 Supply and Fixing of steel tubular pole 7.5 Metre long

designated 410 SP-6 in 1:3:6 cement concrete foundation

including excavation back filling etc.complete in all respects. Set 6

111 Supply and fixing of LED street Fitting having die cast

'Aluminium' body and diffuser with driver set Suitable for

20watt to 50 watt confirming to IP 65 and above protection

on G.I.Pipe bracket complete in all respects.on pole. Each 6

112 2.5sqmm aluminium conductor single core wire for

connection from cable end box to Fitting. Mtr. 85

113 Painting of the pole with 2 coats of aluminium paint over red

oxide primer complete in all respects. Each 6



114 S/F of 32A 415 V TP metal clad rewireable type switch fuse

unit on angle iron bracket complete in all respects. Each 1

SAFETY EQUIPMENTS

115 Supply and fixing danger board fabricated from 10 gauge

M.S. Sheet as per I.E. Rules. Each 1

116 Supplying & fixing of fire extinguisher ABC type 6.00

litre capacity ISI marked IS:15683 & TAC Approved )

complete with initialy charge and wall bracket, along with

supply of all materials and labour for proper completion of Each 1

117 Supply and fixing of fire bucket, round bottom made of

G.I. Sheet 9-11 litres capacity duly painted as per brigade

design, supported on hanging bracket chained and

locked, initially filled with fine river sand, water as per

directions of Engineer- in Charge. Each 1

118 Supply and fixing of shock treatment chart (Prescribed

under I.E. rules) duly framed with glass and supported

from back with hard board or soft board with supply of

all material labour T&P for proper complection of work.Each 1

119 Supply and laying of 1800mm x 900mm x12mm thick

chequered rubbbber matting of tested quality. Each 1

120 First aid box St. John Ambulance Brigade or Indian Red

Cross Society to relevant IS 2217/1963. Each 1

121 Supplying and erection of gate light fixture fabricated out of

M.S. Pipe 4.05mm thick 75mm dia 0.5m long in cement

concrete foundations 1:3:6 complete with 1 No. Bajaj Make

or Equivalent with 40 to 50Watt confirming to IP 65

protection complete with all accessories in outdoor type

control gear box necessary civil work marshelling box

having two no. three way brass connector, one no. 15 amps

kit kat fuses, cable glands, earthing stud, necessary

interconnections and 40mm dia GI Pipe 'B' Class for

protection of the upright cable and painting etc. as required. Each 4

MAIN L.T. PANEL



122 Supply, installation, testing and commissioning of electrical

pane, modular type, front accessible only, free floor standing

confirming to Minimum IP:43 degree of protection. The

panel sheet structure shall undergo seven tank pre-treatment

process before painting. The sheet steel shall be all of

2.2mm thick CRCA sheet. All the openable compartments

of the panel shall be completely shrouded and provided with

padlocking arrangement on all compartments including bus

bar and cable alley chambers. The panel height shall not

exceed 2200mm and the maximum operating height for any

switchgear shall not be more than 1700mm. The panel shall

be provided with minimum 75mm base channel frame

fabricated from ISMC sections. All bus bar links in the

panel shall be solid bus bars with coloured PVC shrinkable

sleeves, no wires will be acceptable. Continuous earth bus

shall run alround the panel with earthing studs provided at

minimum 2 places. The control wiring shall be carried out

with minimum 1.5/2.5 sqmm copper wires and

adequate number of NO/NC, potential free contacts

incorporated for remote operation of the starters. Proper

sized cable termination gland plates shall be provided on

cable alleys and knockouts for same shall be provided during

fabrication stage itself. The panel shall be provided with a

thermostatically controlled heating arrangement (200 W) to

take care of high humidity conditions. A 5A socket service

outlet (single phase) shall be provided in one of the

compartments as ervice outlet in the panel. Panel shall be so

designed at to have minimum 20% spare feeders/space.

Panel shall undergo epoxy powder coated paint, colour as

per IS:5 requirement. All cable terminations shall be from

top. The complete panel shall be fuse less type, for control

circuits 2A/6A MCB's to be used.

All bus bars shall be of aluminium, electrolytic grade only.

Maximum design density shall not exceed 1 Amps/Sqmm.

All bus bars shall be insulated with coloured heat shrinkable

PVC sleeved. All bus bar supports shall be non hygroscopic

DMC/SMC supports.



The panel shall be manufactured in conformance to

requirements of local electrical inspector and it shall be

contractors responsibility to get initial approval of drawings

and also final approval of complete electrical works related

to this section.

The minimum clearances between bus bars shall be as

follows :Phase to phase - minimum 20mm

Phase to neutral-minimum 15mm

a) Main L.T. Panel

Incoming :

One (1) No 200 A 4 pole

Metering :

One (1) No. (0-500V) 96 x 96 Sqmm voltmeter with control

fuse & selector switch.

One (1) No. (0-200A) 96 x 96 Sqmm CT operated Ammeter

with selector switch, CTs etc.

One (1) Set of Phase Indication Lamp.

Bus Bar :

One (1) No.200 A, TPN aluminimum bus bar of suitable length.

Outgoing :

Phase indication lamps on each outgoing to be provided.

80Amps TPN - 1No.

63Amps TPN - 2Nos

40Amps TPN - 5Nos

32Amps DP - 1No

OR outgoing as per site requirment Set 1



123 Fabrication, supplying and installation of outdoor type

external lighting feeder pillar of suitable size not less than

30 cm and upto 45 cm deep made out of M.S. sheet 2mm

thick (14 SWG) duly compartmentalized, double door with

locking arrangement (IP-54), duly fixed on MS angle iron

frame work of size 50mm x 50mm x 6mm, 90 cm long legs

out of which 45 cm duly grouted in cement concrete 1:2:4 (1

cement : 2 sand :4 stone aggrete 20mm) and having

following accessories mounted inside the cubical panel i/c

connection, inter connection with aluminium thimbles,

earthing with two nos. earth struds duly painted with one

coat of red oxide & two coats of superior quality enamel

paint of approved shade complete etc. as reqd.

Supplying & fixing of following accessories in the existing

cubical panel board / feeder pillar including connection

testing etc. as reqd.

Power contactor 3 sets of single pole of suitable ratings

Astronomical Timer, Reference 04767 - Legrand make or

equivalent from GE / Siemens / L&T

The above board shall be complete with 3 nos. phase

indicating lights, flush mounted Ammeter, Voltmeter, CT's,

PT's, selector switches, protective fuses etc. at Incomer with

all interconnections by min. 2.5 sq.mm. Copper wires.

Danger notice plate

Feeder Pillar-1

INCOMER : 63 AMP TPN MCCB (25KA)

BUS BAR : 63AMP, 500 Volts, 3 phase 50 HZ TPN

high conductivity electrolytic Aluminium bus bar. Outgoing :

Phase indication lamps on each outgoing to be provided.

63Amp TP MCB - 1No

32Amp TP MCB - 1No

63Amp TP MCB - 1No-Spare

32Amp TP MCB - 1No-Spare

OR outgoing as per site requirment Set 1

124 Supply and fixing of Pole Box complete as required . Each 6

GRAND TOTAL OF EXTERNAL ELECTRICAL

BILL OF QUANTITY -BSVS-Data Networking



SL.No. DESCRIPTION UNIT QTY. RATE RATE IN WORDSAMOUNT

(in Rs)

DATA / NET WORKING SYSTEM

125 S/F of Surface mount box with I/O Cat 6 and UTP jack D-

Link complete in all respect Make Dlink/Amp Nos 13

126 S/I of Patch cord CAT6 UTP 4 ft. Make Dlink/Amp Nos 13

127 S/I of Patch cord CAT6 UTP 7 ft. Make Dlink/Amp Nos 13

128 S/I/T/C of 24 port category 6e SL Series patch Panel Make

Dlink/Amp with active and passive components,punching,

complete in all respect Nos 1

129 S/I/T/C of 24 port 10/100/1000 Base T Standalone Gigabit

Switch Make Dlink/Amp with active and passive

components, punching, complete in all respect Nos 1

130 S/I/T/C of 802.1 g Indoor wireless access point +

Poe(Business class) Make Dlink/Amp Nos 1

131 Wireless USB Adaptor Make Dlink/Amp Nos 1

132 Supply & Laying of Cable CAT6 UTP in existing conduit

Make Dlink/Amp M 250

133 9U Floor Mount rack with front glass door and rear MS

Door ,6 socket Power Strip unit ,Cable manager, size

18”x24”x18” Nos 1

134 Mapping of Network Nodes & LAN Diagram Job 1

135 1 KVA Single phase UPS Invertor Job 1

GRAND TOTAL DATA NETWORKING

S.N. Description Qty. Unit Rate Rate In Words Amount (Rs.)

SANITARY FIXTURES & ACCESSORIES : I

BOQ-BSVS-Internal Plumbing



136 Providing and fixing water closet squatting pan (Indian type

W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre

low level white P.V.C. flushing cistern, including flush pipe,

with manually controlled device (handle lever) conforming

to IS : 7231, with all fittings and fixtures complete, including

cutting and making good the walls and floors wherever

required

a) White Vitreous china Orissa pattern W.C. pan of size

580x440 mm with integral type foot rests 0 Nos.

b) Same as above but for European type W.C. pan with white

plastic seat and lid.Make- Cera,Hindware. 14 Nos.

137 Providing and fixing white vitreous china extended wall

mounted water closet , of size 780x370x690 mm of

approve shape i ncluding providing & fixing white vitreous

china cistern with dual flush fitting of flushing capacity 3/6

litre(adjustable to 4/8 liters) including seat cover, and cistern

fitting, nuts, bolts and gasket etc. complete. 3 Nos.

138 Providing and fixing wash basin with C.I. brackets, 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard

pattern, including painting of fittings and brackets, cutting

and making good the walls wherever require

a) White Vitreous China Flat back wash basin size 550x 400

mm with single 15 mm C.P. brass pillar tappillar tap. 9 Nos.

139 Providing and fixing wash basin with C.I. brackets, 15 mm

dia C.P. brass Single Hole Basin Mixture approved quality

and make ,including painting of fittings and brackets, cutting

a) White Vitreous China wash basin size 550x 400 mm with

15 mm dia C.P. brass Single Hole Basin Mixture. 2 Nos.

140 Providing and fixing Stainless Steel A ISI 304 (18/8)

kitchen sink as per IS : 13983 with C.I. brackets and

stainless steel plug 40 mm, including painting of fittings and

brackets, cutting and making good the walls wherever

required Kitchen sink with drain board of size 510x1040x200mm 3 No.

141 Providing and fixing flexible P.V.C. waste pipe for sink or

wash basin including PVC waste fittings complete.

Felxible pipe

a) 32mm dia 0 Nos.

b) 40mm dia 3 Nos.



142 Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin of 430x260x350 mm

and 340x410x265 mm sizes respectively with automatic

flushing cistern with standard flush pipe and C.P. brass

spreaders with brass unions and G.I clamps complete,

including painting of fittings and brackets, cutting and

a) One urinal basin with 5 litre white P.V.C. automatic

flushing cistern 1 Each

b) Range of two urinal basins with 5 litre white P.V.C.

automatic flushing cistern 1 Each

c) Range of three urinal basins with 10 litre white P.V.C.

automatic flushing cistern 0 Each

143 Providing and fixing stone slab table rubbed, edges rounded

and polished of size 75x50cm deep and 1.8cm thick fixed in

Urinal partitions by cutting a chase of appropriate width with

chase cutter and embedding the stone in the chase with

epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse

sand: 4graded stone aggregate 6mm nominal size) as per

direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade 1 Sqm.

144 Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P.

brass screws and washers complete. 11 No.

145 Providing and fixing 8 mm dia C.P./S.S. Jet with flexible

tube upto 1 meter long with S.S. triangular plate for

Eureopean type W.C. of quality and make as approved by

engineer-in-charge.15mm nominal bore 17 Each

146 Providing and fixing CP Brass 32 mm size Bottal Trap of

approved quality & make and as per thedirection of Enginer-

in-charge. 14 Each

147 Providing and fixing CP Brass Single lever lelephonic wall

mixture of quality & make and as per thedirection of

Enginer-in-charge.a) 15mm dia nominal dia. 8 Each



148 Providing and Fixing C.P. brass Ablution health faucet

assembly with 1.0 m long braided PVC hose with mounting

bracket fixed on wall complete.[FOR EWC]-Make-

JAQUAR ALD-565 17 Each

149 Providing and fixing C.P. brass Two-way angle valve for

EWC points & for fixing Ablution Health Fauct of approved

quality conforming to IS:8931. 15 mm nominal bore-ESSCO

SQT 526AKN 17 Each

150 Providing & fixing 60x2cm. C.P. brass towelrail complete

with C.P. brass brackets fixed to wooden cleats with C.P.

brass screw. ESSCO AEC-1181 9 Each

151 Supplying & Fixing of CP soap tray fixed to the wall with

PVC rubber plug with CP brass screws- Make-ESSCO AEC-

1131 22 Each

152 Providing 15 mm dia. inlet C.P. brass Providing and Fixing

C.P. Single flow overhead shower(With Arm)-Make-

ESSCO EOS-542A-125MMDIA 8 Each

153 Providing and Fixing Floor Trap Plain or Hole cut

Grating / Jali 5'' Round , Stainless Steel with all complete.-

Sunflex 33 Each

Sub Total

SOIL WASTE & VENT PIPES AND FITTINGS - II

154 Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes,

having thermal stability for hot & cold water supply

including all

CPVC plain & brass threaded fittings This includes jointing

of pipes

& fittings with one step CPVC solvent cement, trenching,

refilling &

testing of joints complete as per direction of Engineer in

Charge.a) 100 mm nominal inner dia Pipes 165 Rm.

b) 75 mm nominal inner dia Pipes 310 Rm.



155 Providing and fixing on wall face unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A including

jointing with seal ring conforming to IS : 5382 leaving 10

mm gap for thermal expansion . (i) Single socketed pipes.

a) 110mm diameter 245 Mtr

156 Making khurras 45x45 cm with average minimum thickness

of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over PVC

sheet 1m x 1 m x 400 micron, finished with 12 mm cement

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement,punning,rounding the edges and making and

finishing the outlet complete.

a) 110mm 11 Nos.

157 Providing and fixing unplasticised -PVC pipe clips of

approved design to unplasticised - PVC rain water pipes by

means of 50x50x50mm hard wood plugs, screwed with M.S.

screws of required length including cutting brick work and

fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and

making good the wall etc. complete.

a) 110mm 56 Nos.

158 Providing and fixing to the inlet mouth of rain water pipe

cast iron grating 15 cm diameter and weighing not less than

440 grams. 11 Nos.

Sub Total

WATER SUPPLY PIPES AND FITTINGS - III


(CPVC) pipes,

having thermal stability for hot & cold water supply,

including all

CPVC plain & brass threaded fittings, including fixing the

pipe with

clamps at 1.00 m spacing. This includes jointing of pipes &

fittings

with one step CPVC solvent cement and testing of joints

complete

as per direction of Engineer in Charge.i) (Internal work) Exposed on wall

a)25 mm nominal outer dia Pipes 135 Rm.

b) 32 mm nominal outer dia Pipes 110 Rm.



c) 50 mm nominal outer dia Pipes 55 Rm.

ii) Concealed work, including cutting chases and making good

the

a) 15 mm nominal outer dia Pipes 210 Rm.


160 Providing & fixing CP brass bib cock of approved quality

conforming to IS 8931 a) 15mm nominal bore 17 Nos.

161 Providing & fixing C.P. brass long body bib cock of

approved quality conforming to IS standards and weighing

a) 15mm nominal bore 8 Nos.

162 Providing & fixing C.P. brass angle valve for basin mixer

and gyser points of approved quality conforming to IS 8931

a) 15mm nominal bore 42 Nos.

163 Providing and fixing gun metal gate valve with wheel of

approved quality.a) 20 mm dia nominal bore 7 Each

b) 25mm dia nominal bore 3 Each

c) 32mm dia nominal bore 5 Each

d) 50mm dia nominal bore 1 Each

Sub Total

SCHEDULE OF QUANTITIES FOR INTERNAL SEWERAGE SYSTEM - IV

164 Excavating trenches in all kind of soil of required width for

pipes, cables etc. including excavation for sockets and

dressing of sides, ramming of bottoms, depth upto 1.5 m.

including getting out the excavated soil & then returning the in layers not exceeding 20cm in depth including

consolidating each deposited layer by ramming, watering, etc

& disposig of surplus excavated soil as directed within a lead

a) Pipes 80mm to 300mm diameter. 155 RM

165 Providing, laying and joining glazed stone ware pipes grade

'A' with stiff mixture of cement mortar in the proportion of

1:1 (1 cement : 1 fine sand) including testing of joints etc. a) 100mm diameter 45 M

b) 150mm diameter 110 M

166 Providing & laying cement concrete 1:5:10 (1 cement :5

coarse sand :10 graded stone aggregate 40mm nominal size)

alround S.W. Pipes including bed concrete as per standard



a) 100mm diameter S.W. Pipe 45 M

b) 150mm diameter S.W. Pipe 110 M

167 Providing and fixing square mouth S.W. Gully trap grade 'A'

complete with C.I. grating brick masonry chamber with

F.P.S. bricks of class designation 75 and water tight C.I.

cover with frame of 300 x 300mm. size (inside) the weight

of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as

per standard design.a) 150 x 100 mm. size P type

With Sewer bricks conforming to IS : 4885 8 Nos

168 Constructing brick masonry manhole in cement mortar 1:4 (1

cement :4 coarse sand) RCC top slab with 1:2:4 mix (1

cement :2 coarse sand :4 graded stone aggregate 20mm

nominal size), foundation concrete 1:4:8 mix (1 cement :4


inside plastering 12mm thick with cement mortar 1:3 (1

cement :3 coarse sand) finished with floating coat fo neat

cement and making channels in cement concrete 1:2:4 (1


nminal size) finished with a floating coat of neat cement

complete as per standard design

Inside size 90x80cms and 45cms deep including CI cover

with frame (light duty) 455x610mm internal diamensions

total weight of cover and frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15kg).

With FPS bricks of class designation 75

(i) For Sewer Line 11 Each

Extra for depth of man hole size 90x80 cm 2.5 metre

Inside size 90x120 cm & 90 cm deep including C.I. cover

with frame (medium duty) total wt. of cover & frame to be

not less than 116 Kg (wt. of cover 58 Kg & wt. of frame 58

Kg.0 Each

Extra for depth of man hole size 90x120 cm 0 metre



169 Constructing masonry Chamber 60x60x75 cm, inside with

75 class designation brick work in cement mortar 1:4 (1

cement :4 coarse sand ) for sluice valve, with C.I. surface

box 100mm top diameter, 160mm bottom diameter and

180mm deep (inside) with chained lid and RCC top slab

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size) necessary excavation

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10

graded stone aggregate 40mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12 mm thick finished with a floating coat of neat cement

complete as per standard design :With F.P.S. bricks 2 Each

170 Providing M.S. foot rests including fixing in manholes with

20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3

coarse sand :6graded stone aggregate 20 mm nominal size)

as per standard designWith 20x20 mm square bar 26 Nos

Sub Total

SUMMARY OF COST

SANITARY FIXTURES & ACCESSORIES

SOIL WASTE & VENT PIPES AND FITTINGS

WATER SUPPLY PIPES AND FITTINGS

INTERNAL SEWERAGE SYSTEM

GRAND TOTAL INTERNAL PLUMBING





including getting out the excavated soil & then returning the

soil as required,

BOQ-BSVS-Exterior Plumbing

SCHEDULE OF QUANTITIES FOR EXTERNAL SEWERAGE SYSTEM - I



in layers not exceeding 20cm in depth including



of 50m.a) Pipes 80mm to 300mm diameter. 45 RM



1:1 (1 cement : 1 fine sand) including testing of joints etc. a) 150mm diameter 45 M

173 Providing & laying cement concrete 1:5:10 (1 cement :5


alround S.W. Pipes including bed concrete as per standard

design.a) 150mm diameter S.W. Pipe 45 M

174 Constructing brick masonry manhole in cement mortar 1:4 (1

cement :4 coarse sand) RCC top slab with 1:2:4 mix (1


nominal size), foundation concrete 1:4:8 mix (1 cement :4


inside plastering 12mm thick with cement mortar 1:3 (1

cement :3 coarse sand) finished with floating coat fo neat

cement and making channels in cement concrete 1:2:4 (1


nminal size) finished with a floating coat of neat cement

complete as per standard design

Inside size 90x80cms and 45cms deep including CI cover

with frame (light duty) 455x610mm internal diamensions

total weight of cover and frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15kg).

With FPS bricks of class designation 75

(i) For Sewer Line 0 Each


Inside size 90x120 cm & 90 cm deep including C.I. cover

with frame (medium duty) total wt. of cover & frame to be

not less than 116 Kg (wt. of cover 58 Kg & wt. of frame 58

Kg. 1 Each




175 Providing orange colour safety foot rest of minimum 6mm

thick plastic encapsulated as per IS : 10910 on 12mm dia

steel bar conforming to IS: 1786 having minimum cross

section as 23 mm x25mm and over all minimum length

263mm and width as 165mm with minimum 112mm space

between protruded legs having 2mm tread on top surface by

ribbing or chequering besides necessary and adequate

anchoring projections on tail length on 138 mm as per

standard drawing and suitable to with stand the bend test and

chemical resistance test as per specifications and having

manufactures's permanent identification mark to be visible

even after fixing, including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20mm nominal size)

complete as per design. 4 Each

176 Making connection of drain or sewer line with existing

manhole including breaking into and making good the walls,

floors with cement concrete 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) cement

plastered on both sides with cement mortar ( 1 cement : 3

coarse sand) finished with a floating coat of neat cement and

making necessary channels for the drain etc. complete :

For pipes 100 to 250mm diameter 1 Each

EXTERNAL WATER SUPPLY SYSTEM -II


(CPVC) pipes, having thermal stability for hot & cold water

supply including all CPVC plain & brass threaded fittings

This includes jointing of pipes

& fittings with one step CPVC solvent cement, trenching,

refilling & testing of joints complete as per direction of

Engineer in Charge.a) 62.50 mm nominal inner dia Pipes 35 Rm.


178 Providing & filling sand of grading zone V or coaser grade

alround the G.I. Pipes in external work.

a) 65mm nominal bore. 35 Rm.

b) 50mm nominal bore. 65 Rm.

179 Providing and fixing gate valve (with cap complete with

bolts, nuts, rubber insertion etc.

a) 65mm 1 Nos.



b) 50mm 1 Nos.

180 Constructing masonry Chamber 30x30x50 cm, inside with

75 class designation brick work in cement mortar 1:4 (1

cement :4 coarse sand ) for stop cock, with C.I. surface box

100x100x75mm (inside) with hinged cover fixed in cement

concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) necessary excavation

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10

graded stone aggregate 40mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12 mm thick finished with a floating coat of neat cement

complete as per standard design :

With F.P.S. bricks 2 Each

DRAINS -III

181 Constructing brick masonry open surface drain with bricks

of class designation 75 in cement mortar 1:4 (1 cement : 4

fine sand) including earth excavation, 10cm thick bed

concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone

aggregate 40mm nominal size) and 25mm thick cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 12.5mm nominal size) for filling haunches

including 12mm cement plaster 1:4 (1 cement : 4 coarse sand

) with a floating coat of neat cement inside the drain, its top

and exposed side including disposal of surplus earth

complete as per standard design:

25cm drain 30 cm average depth 105.00 Metre

TOTAL(I+II)

TOTAL (III)

GRAND TOTAL OF EXTERNAL PLUMBING

(I+II+III)


BOQ - BSVS - Rain Water Harvesting



182 Earth work in excavation by mechanical means (Hydraulic

excavatior)/manual means over areas(exceeding 30cm in

depth. 1.5m in width as well as 10sqm on plan) including

disposal of excavated earth, lead upto 50m and lift upto

1.5m, disposed earth to be levelled and neatly dressed.

In all kind of soil upto 1.5m depth 16.033 Cum

In all kind of soil upto 1.5m to 3.0m. depth 16.033 Cum

In all kind of soil upto 3.0m to 4.5m. depth 12.792 Cum

183 Providing and laying in position cement concrete of

specified grade excluding the ccost of centering and

shuttering -All work up to plinth level:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size). 0.799 Cum

184 Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand) 16.627 Cum

185 Reinforced cement concrete work inbeams, suspended

floors, roofs having slope up to 15º landings, balconies,

shelves, chajjas, intels, bands plain window sills, staircases

and spiral stair cases up to floor five level excluding the cost

of centering, shuttering, finishing and reinforcement with

1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate

20mm nominal size) 1.068 Cum

186 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all

complete upto plinth level.Mild steel and Medium Tnsile steel bars. 84 Kg

187 Centring and shuttering including struting , proping etc and

removal of form for :

Suspended floors, roofs, landings, balconies and access

platform. 10.689 Sqm

188 15mm cement plaster on rough side of single or half brick

wall mix

1:4 (1 cement : 4 coarse sand) 37.39 Sqm

189 Providing M.S. foot rests including fixing in manoholes with

20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3

coarse sand : 6 graded stone aggregate 20mm nominal size)

as per standard design:

With 20x20mm square bar 12 Nos.

PART A



190 Providing and fixing in position precast RCC manhole cover

and frame of required shape and approved quality.

M.D. -10- Circular shape 500mm internal diameter 2 No.

191 Boring/drilling bore well of required dia for casing/ strainer

pipe, by suitable method prescribed in IS: 2800 (part I),

including collecting samples from different strata, preparing

and submitting strata chart/bore log, including hire &

running charges of all equipments, tools, plants &

machineries required for the job, all complete as per

direction of Engineer-incharge, upto 90 metre depth below

ground level.

Drilling of 300mm dia bore hole manually. 25 M

Supplying, assembling, lowering and fixing in vertical

position in bore well unplasticized PVC medium well screen

(RMS) pipes with ribs, conforming to IS: 12818, including

hire & labour charges, fittings & accessories etc. all

complete, for all depths, as per direction of Engineer-in-

charge.150 mm nominal size dia 25 M

192 Supplying, filling, spreading & leveling stone boulders of

size range 5 cm to 20cm, in recharge pit, in the required

thickness, for all leads & lifts, all complete as per direction

of Engineer-in-charge. 3.53 cum

193 Supplying, filling, spreading & leveling gravels of size range

5 mm to 10mm, in the recharge pit, over the existing layer of

boulders, in required thickness, for all leads & lifts, all

complete as per direction of Engineer-in-charge. 3.53 cum

194 Supplying, filling, spreading & leveling coarase sand of size

range 1.5 mm to 2mm in recharge pit, in required thickness

over gravel layer, for all leads & lifts, all complete as per

direction of Engineer-in-charge. 3.53 cum



195 Gravel packing in tubewell construction in accordance with

IS: 4097, including providing gravel fine/medium/coarse, in

required grading & size as per actual requirement, all

complete as per direction of Engineer-in-charge. 1 Cum

TOTAL - 1 NO. PIT

EXTERNAL PIPE NETWORK SYSTEM





soil as required,in layers not exceeding 20cm in depth including



of 50m.a) Pipes 80mm to 300mm diameter. 110 RM



1:1 (1 cement : 1 fine sand) including testing of joints etc.

complete.a) 150mm diameter S.W. Pipe 105 M


198 Providing and laying cement concrete 1:5:10 (1 cement : 5

coarse sand :10 graded stone aggregate 40 mm nominal size)

all-round S.W. pipesincluding bed concrete as per standard

design :a) 150mm diameter S.W. Pipe 105 M


SUB TOTAL PART A

PART B

199 Constructing brick masonry manhole with 75 class

designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4

coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2

coarse sand: 4graded stone aggregate 20mm nominal size);

foundation concrete 1:4:8 mix (1 cement :4 coarse sand: 8 graded stone aggregate 40mm

nominal size) inside plasstering 12mm thick with cement

mortar 1:3 (1 cement :3 coarse sand) finished with a floating

coat of neat cement and making channels in cement concrete

1:2:4



(1 cement :2 coarse sand : 4 graded stone aggregate 20mm

nominal size) finished with a floating coat of neat cement

complete as per standard design.a) Inside size 60x60 cm & 90 cm deep including C.I. cover

with frame (light duty) total wt. of cover & frame to be not

less than 38 Kg (wt. of cover 23 Kg & wt. of frame 15 Kg. 13 Nos

SUB TOTAL PART B

TOTAL PART A

TOTAL PART B

GRAND TOTAL OF RAIN WATER HARVESTING

( PART A+PART B) Rs.


ST1 Size :- Length = 7.50 M. Width = 2.65M Total Depth

=3.00M

200 Earth work in excavation over areas including disposal of

excavated earth, lead upto 50m, disposed earth to be levelled

and neatly dressed.

In all kind of soil upto 1.5m depth 37.133 Cum

In all kind of soil upto 1.5m to 3.0m. depth39.609 Cum

201 Providing and laying of cement concrete in base excluding

the cost of centring and shuttering by 1:2:4 (1 cement : 2

coarse sand : 4 gradded stone aggregae 20mm nominal size) 2.476 Cum

202 Brick work with brick of class designation 150 in foundation

and plinth in cement mortar (1 cement : 4 coarse sand) 18.476 Cum

203 Reinforced cement concrete work in slab with 1:1.5:3 (1

cement : 1.5 course sand : 3 graded stone aggregate 20mm

normal size). 2.292 Cum

BOQ - BSVS - Septic Tank



204 Reinforcement for R.C.C. work including, straightening,

cutting bending binding and placing in position complete. 180 Kg

205 Centring and shuttering including struting , proping etc and

removal of form for slab. 22.925 Sqm

206 15mm cement plaster on rough side of mix 1:4 (1 cement : 4

course sand) 80.33 Sqm

207 Providing M.S. foot rest including fixing with 20x20x10 cm.

cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6

gradded aggregate of nominal size 20mm ) as per standard

design with 20x20mm sq bars. 12 Nos.

208 Providing and fixing C.I. tee at the inlet and outlet of septic

tank. 2 Nos.

209 Providing & fixing 75mm dia vent pipes. 1 Rm.

210 Providing & fixing of 75mm dia cast iron terminal guard. 1 No.

211 Providing and fixing in position precast RCC manhole cover

and frame of required shape and approved quality.

M.D. -10- Circular shape 500mm internal diameter

2 No.

L.D. -2.5- Circular shape 450mm internal diameter 4 No.

212 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45

cm dry brick honey comb shaft with bricks of class

designation 75 and S.W. drain pipe 100 mm diameter, 1.8m

long complete as per standard design.With F.P.S. bricks 1 No.

GRAND TOTAL OF SEPTIC TANK



Sl.No. ITEM OF WORK UNIT QTY. Rate RATE IN WORDS AMOUNT

213 Transportation Charges of drilling equipment including

assembly and other material as required. JOB 1

214

a Supply & fixing of 1500 mm or required dia of M.S Ring

NO. 4

b

c Supply & fixing Bail plug 200 mm or of required dia M.S.

NO. 1

d Supply & fixing Well Cap 200 mm or of required dia M.S.

NO. 1

e Supply & fixing Reduser of required size dia M.S./PVC high

pressure. NO. 1

f Supply & fixing Housing clamp of required dia M.S/PVC

high pressure. Pair 1

215 Providing submersible pump boring for supply of water as

per the job:-

a Drilling of 200mm or more dia bore 90 m deep manually.

b Supply of 150mm dia plain rigid PVC pipe (4 Kg. /sqcm

pressure rating) 60 m and acessories.

c Supply of 2" or more dia as per requirement of system

coulmn pipe 50 m and strainer rigid PVC pipe (4 Kg. /sqcm

pressure rating) 20 m and acessories.d Supply and fixing of nylon jali around the slotted pipe

complete as required.

e Providing and packing of coarse sand around the pipe.

f Transport of boring tools other required equipments,

including ather assemblies etc. complete and installation at

site.g Supply of 3.0 HP submersible pump of approved make with

control panel, support wire etc. complete.

g

BOQ-BSVS-Tubewell

Construction of Tubewell and S/F of 3.0 H.P

Submersible Pump Set,

Supply & filing of Pee gravel 1.6 mm to 2 mm in side of

bore after lower and development as required as per

direction of E/I. as per requirement. Development by air

compressor and Development of O.P. unit including

transportation as per required hour are inclusive of quoted

cost.JOB 1



h Providing 3 core 2.5sqmm. PVC insulated copper conductor

submersible cable. (from pump panel to submersible pump)

i Providing and fixing 50mm dia G.I. pipe complete with

fitting and clamps including cutting and making good tha

wall etc. (from submersible pump to ground level)j Providing and fixing 50mm. Dia brass gate valve with CI

wheel of approved quality.

k Lowering of 100mm. Did rigid PVC pipe in bore hole

including cutting, jointing, etc. complete.

l Supply and fixing of tube well acessories i.e. well cap, clips,

clamps, etc. to complete the job in all respect.

m Fixing, testing and commissioning for erection and lowering

of submersible pump, 50mm dia GI column pipe, 3 core

2.5sqmm. Submersible copper copper cable upto the control

panel, supporting clamps, cable clips pressure gauge,

connection line and all other acessories required for the

proper completion of the work.

n Testing and development of tube well. Cost includes pump

motor and other related items all complete.

216

217 Supply and fixing of finolex of copper cable ISI marked

submersible cable of size 1 x 3 x 4 sq mm M 120

218 Supply of control panel board cubical type wall mounted

vermin proof with internal wiring duly enameled painted for

mechanically finished having L&T or equivalent make

switch fuse unit with HRC fuses, ammeter, voltmeter,

selector switch phase indication lamp with bulb (instrument

fuses, power capacitor, single phase preventer complete set

with supply of L&T Jyoti or equivalent Air break Star-Delta

motor starter suitable for above pump set. NO. 1

219

a Supply of 80mm dia M.S./PVC column pipe clamps with nut

bolts packing etc. NO. 2

b Supply of 80mm dia C.I. double flanged ISI mark reflex

valve of upadhya or equ. Make NO. 1

c Supply of 80mm dia C.I. double flanged ISI mark sluice

valve with hand wheel of upadhya or equ. Make. NO. 2

d Supply of C.I. double flanged bend of 80 mm dia i/c cost of

material and labour. NO. 1

e Supply of 80mm dia C.I. tee heavy quality i/c cost of

material. NO. 1

f Supply of Guru/Fiibing or equivalent make pressure gauge.

NO. 1

JOB 1



g Erection & commissioning of pumping plants comp along

with electric wiring. NO. 1

h Supply of steel wire rope of 1/2" size M 100

i S/B of 600 mm x 600 MM x 6.0mm G.I. plate vertically for

earthing with its top at least 3 metres below ground level

complete with 20mm dia G.I. pipe and funnel for watering

and one earthing lead on one no. 8 to 10 SWG GI wite in

15mm dia G.I. pipe up to switch board (from appron to

switch board the cost of G.I. , pipe and G.I. wire will be

extra ) 30 cm square C.I. frame with hinged cover masonry

housing alternate layers of charcoal/coke and salt at least

150mm thick alround etc. as per directions of E/I complete

in all respects as per drawing. NO. 1

j S/F of one number 8 to 6 SWG G.I. Wire in 15mm dia G.I.

Pipe for earthing, laid in ground or in wall duly concealed

including the cost of cement, sand labour. T&P other

material required for proper completion of the work as

directed at site. M 8

GRAND TOTAL OF TUBEWELL



S.N. DESCRIPTION QTY. UNIT RATE RATE IN WORDS AMOUNT

PART-I

A)



dressing of sides, ramming of bottoms, depth upto 1.5m.


soil as requiredin layers not exceeding 20cm in depth including

consolidating each deposited layer by ramming, watering etc.

& disposing of surplus excavated soil as directed within a

a) Pipes 80mm to 300mm diameter. DSR-16(2.10.1.2) 85 RM

221 Constructing masonry Chamber 60x60x75cm, inside with 75

class designation brick work in cement mortar 1:5 (1 cement

: 5 fine sand) for fire hydrants, with C.I. surface box

350x350mm top and 165mm deep (inside) with chained lid

and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

nominal size) necessary excavation foundation concrete

1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate

40mm nominal size) and inside plastering with cement

mortar 1:3 (1 cement : 3 coarse sand ) 12mm thick finished with a floating coat of

neat cement complete as per standard design. DSR-

16(18.36.1)1 Each

222 Supply & fixing of fire extinguisher, ABC Type 6.00 kg.

capacity(ISI Marked IS:15683 & TAC approved) comlete

with initial charge and wall bracket, along with supply of all

materials and labour for proper completion of work.PWD-

2016-1131 (A) 6 Each

223 Supply & fixing of CO2 type fire extinguisher, 6.5 kg.

capacity(ISI Marked IS:2878 & TAC approved) comlete

with initial charge and wall bracket, along with supply of all

materials and labour for proper completion of work.PWD-

2016-1132 (A) 6 Each

TOTAL ( A ) Rs

B)

BOQ - FIRE Fighting And Fire Detecting System(Internal And External)



224 Supply, Installation, Testing and Commissioning of one coat

of 4 mm thick 'PYPKOTE' or coatek tape anti rust pipe

protection , primer and lap of 25 mm on external M.S. pipes

to make an impermeable layer in trenches or on

structural/masonry members complete including surface

preparation.

100 mm dia 85.00 M

225 S/I/T/C stand post type fire hydrant with 63mm. outlet

complete with bolts, nuts and rubber insertions etc. as per the

standard design conforming to 15-908-'75. 1.00 Each

226 Supply, Installation, Testing & Commissioning of Fire

brigade inlet with 63 MM dia instantaneous inlet complete

with all necessary fittings and MS enclosure with glass door

made of 18/16 SWG sheet. (Newage/Omex/Padmini)-4 Way 1.00 Each

Total PART (B)

Total PART 1(A+B ). Rs

PART-II(FIRE FIGHTING INERNAL)

SUB HEAD-I

227 Supply, erection and testing of ISI marked M.S pipes (Class

B) and specials etc. (as per IS : 1239) for above ground

laying for hydrants and sprinkler system including

transportation of materials upto the worksite, cutting the

pipes to required length, edge preperation, welding,

fixing/erection of pipes with suitable flat/angle iron

including specials i.e. bends tees, reducers, flanges etc. in

proper position including all supports as per layout,

including hangers for sprinkler piping, jointing by welding,

aligning the pipe line, painting with a primer coat and two

coats of synthetic enamel fire red colour, providing tapping

for pressure gauges and for other instruments etc.

Hydrostatic testing of system as specified, flushing &

cleaning by water etc. complete as per drawings & direction

of the Engineer-in-charge. The quoted rats shall also include

for making holes in masonry/RCC slab, wall, chases in wall

etc. & making good the same to original conditions.

MAKE : Jindal(Hissar)/ Bharat/Indian Tube/ Prakash)

a) 100mm 110 M

b)80mm 25 M



c) 25mm 20 M

228 Supply & fixing in position ISI marked cast iron double

flanged butterfly valves as per IS :13095, suitable for

pressure 15 KG/cm2 including transporting to worksite,

supply & fixing nuts, bolts, gaskets, flanges & washers etc

including testing, complete as per drawing & directions of

the Engineer-in-charge. (MAKE : Kirloskar/

Venus/IVC/Zaloto/Kalpna)

100 MM NB 1.00 Nos

229 Supply & fixing in position ISI marked cast iron double

flanged Non Return Valves as per IS 5312, part -I including

transportation to worksite, supply & fixing nuts, bolts

gaskets and washers etc, complete with testing as per

direction of the Engineer-in-charge.(MAKE : Kirloskar/ Venus/IVC/Zaloto/Kalpna)

100 MM NB 1.00 Nos

230 Supply, fixing, testing & commissioning of 20mm bore and

30 meter long hose (Rubber lined dunlop pipe) and hose reel

for first aid fire fighting conforming to IS : 884, with full

swing drum, fixing brackets, 5mm dia shut off gun metal

nozzle, 32 mm dia hand lever operated ball valve,

connecting directly from the riser through 32mm dia GI pipe

with sockets, elbows, nipples etc, including providing

operating instructions on a metal plate and fixing it near hose

reel. The system shall be complete in all respects as per

drawings and directions of Engineer-in-charge. (Make : 3.00 Nos

231 Supply, Installation, Testing and Commissioning of single

headed S.S metal ISI marked oblique pattern hydrant landing

valve Type "A" 80 mm. Dia flanged inlet & 63 mm. Dia

Instantaneous type female coupling outlet complete with

gunmeta cap & chain twist release type lug and all

accessories as per (IS:5290:1983). (Make :

Minimax/Firex/Safex/ Newage) 3.00 Nos

232 Providing gun metal ISI marked 63MM dia Instantaneous

pattern short branch pipes & 16mm dia Nozzle suitable for

interconnections to hose pipe coupling as required. (Make :

Minimax/Firex/Safex/ Newage)

a) 100mm 3.00 Nos



233 Providing ISI marked RRL (IS: 636 type-II) fire hose pipe

15 meter long and 63 mm dia with ISI marked (IS : 903) gun

metal male and female coupling complete as required.

(Make : Jayshree/Newage) 6.00 Nos

234 Providing & fixing standard firemans axe with heavy rubber

handle. 3.00 Nos

235 S/I/T/C draining arrangement with vertical down comer

complete in all respect 1.00 Each

236 Providing, fixing, testing & commissioning of Pressure

meter. 1.00 Each

237 Providing, fixing, testing & commissioning of motor starter

panel. 1.00 Each

238 Providing, fixing, testing & commissioning of 10 sq mm 3

core wire for fire pump (Aprox) 125 M

239 S/I/T/C air vessel of suitable capacity made out of 6mm.

thick MS. sheet with legs for bolting wall drain cock etc.

complete in all respects. 1.00 Each

240 Providing and fixing standard fire hose cabinet door

(1000mm x 1800mm) suitable to fit in the duct made of not

less than 16 SWG MS sheet having central opening glassed

door (4 mm thick clear glass) including necessary locking

arrangement with handle as required including painting (one

coat primer and two coats of fire red colour). The door shall

be fixed in the masonry wall or as required. The words Fire

Hose to be painted on the box. 3 Nos

241 Supply, fixing , testing & commissioning of electrical motor

driven fire pump suitable for automatic operation consisting

of following : (Terrace Pump) (Make :

Kirloskar/Mather+Platt)



(a) Horozontally mounted, split casing, Centrifugal fire

pump complete for delivery of under mentioned discharge

against desired mentioned head so as to ensure a minimum

pressure of 30 meter at the highest and farthest outlet at the

specified flow cmplete with necessary strainers, pressure

gauge including bypass arrangement for periodic testing of

the working of the pumpset with required length and size of

medium class GI pipe and control valves for proper

completion of work. The pump shall be capable of giving

150% of rated discharge at head not less than 65% of rated

head. The pump shall be provided with Mechanical seals.

The impeller shall be enclosed type and accurately blanced

dynamically. The pump casing shall be of cast iron, impeller

shall be of bronze and shaft shall be of stainless steel.

(b) Squirrel cage, TEFC induction motor suitable for 415 V,

3 phase having IP 55 protection and class 'B' insulation for

the above pump and flexible coupling with the pump. The

motor shall b rated for continuous duty and shall have HP

rating necessary to drive th pump at 150% of it's rated

discharge at 65% of rated head.

(c)Common bed plate of fabricated mild steel channel or cast

iron type.

(d) Suitable cement concrete pump foundation and vibration

clamping arrangement as required with foundation bolts, anti

vibration pads, washers etc.(e) Pressure switch for automatic operation of motor

including necessary wiring upto control panel.

(f) Electrical Control panel with starter, 3 Pole motor

protection category current limiting type MCCB, indicating

light, ammeter, voltmeter, selector switches, CT's protective

fuses, single phasing protection, dry suction cut off etc as

requrd as per standard details.Discharge : 450 liter per minute

Head : 25 meter 1 Set

TOTAL SUB HEAD-I Rs

SUB HEAD-II

FIRE DETECTION SYSTEM



242 Supply, fixing, installation, testing and commissioning of

dust proof type push button to initiate audio visual alarm

with a breakable glass cover as per specification complete

with small steel hammer attached with steel chains as

required (mannual call points) 3 nos

243 Supply, fixing, installation, testing and commissioning of

Fire Alarm Hooter/Hooter cum speaker having an audio

range of 25 meter in custom built cabinet 3 nos

244 Supply, fixing, installation, testing and commissioning of 6

Zone Main control panel with window type annunciation to

indicate fire and fault, lead lamps for visual indication, audio

alarm unit, push button for acknowledge, test, reset complete

with power supply. 1 set

245 Wiring with 2X1.5 sqmm solid PVC insulated copper

conductor 100 volt grade wires in existing concealed conduit

including terminations, all labour and material etc complete 325 rmt

246 Supply and fixing in position the following sizes of 20 mm

dia 2mm thick PVC conduit including providing all

accessories 225 rmt

247 Supply/Fixing of self illuminated "EXIT" sings made out

from not less than 4 mm of transparent acrylic sheet of 300 x

150 mm size with self illuminated plastic words of 100 mm

height suspended from ceiling by means of M.S. chain or

fixed of the walls as required and as directed at site.

3 nos

TOTAL SUB HEAD-II Rs.

GRAND TOTAL OF FIRE FIGHTING AND FIRE

DETECTION(PART-I+II) Rs.


Documents

BILL OF QUANTITIES Baroda Swarojgar Vikas Sansthan · vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: