Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
1
1.1 117
Providing Office space of minimum 40 Sq.m including
toilet, necessary furniture, Equipment such as Computer,
All in one A4 size printer, photo copier, fax with all
necessary software and accessories to Engineer's site
office including running cost of office like stationeries,
Internet/telephone service, electricity and water supply,
soap, towels, toiletries etc. during contract time till the
completion and handing over of the site.
Months 15.00
1.2 107
Provision and maintenance of Project Signboard of
1800mm x 1200mm size with complete information of
the Project and cautionary and informatory signs as
required and directed by the Engineer.
Lum-
sum1.00
1.3 124
Establishment of New Laboratory along with the
Engineer's office with all required testing equipments as
per technical specifications
Months 15.00
2.0
2.1 300
Surface dressing of ground including removal of
vegetation and inequalities <150mm deep, disposal of
rubbish to any lead and lifts
sq.m 45.00
2.2 302
Earthwork in excavation over areas, exceeding 300mm
in depth, ecceding 1.5 m in width as well as exceding 10
sq.m on plan, proper compaction using 12Mt vibrator
roller,including disposal of excavated earth to any leads
and lifts (disposed earth to be levelled and neatly
dressed)
cu.m 44,648.84
EARTHWORK
SITE FACILITIES
BILL OF QUANTITIES (Civil Works)
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
Page 1 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
2.3 302
Filling of trenches, sides of foundation etc. in layers ˂
200mm using selected excavated earth, ramming etc-
any lead and lift.
cu.m 4,316.15
2.4 503Providing & laying sand bedding, including watering,
ramming, dressing and e.t.ccu.m 289.55
2.5 300
Hand excavation and refilling in layers < 200mm, of
trenches for pipes & sockets, cables, including dressing
of sides/ ramming of bottom, depth upto 1.5m, to any
lead and lift: All kinds of soil
m 1,739.00
2.6 303 P/L dry earth beding including consolidation each
deposited layer by watering and ramming cu.m 4.63
2.7 303
Construction of embarkment by providing and laying
dry earth in horizontal layers not exceeding 200mm in
depth(compacted), including watering,power
rolling,dressing and preparation of site with selected
excavated earth within any lead and lift.
cu.m 1,080.00
3.0
3.1 202
Demolishing stone rubble masonry including stacking
useful materials & disposal of rubbish within any lead in
cement motor
cu.m 31.21
3.2 1200Providing and laying Hand packed stone filling or soling
with stones cu.m 3,810.94
3.3 1200Providing & laying Random Rubble Masonry with hard
stone in foundation & plinth-In cement mortar 1:4cu.m 414.04
4.0
4.1 1100Providing & laying Second-Class Brick work in All
Works in all lvel-In cement mortar 1:4cu.m 427.81
STONE/MUD WORK
BRICK WORK
Page 2 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
4.2 1100Providing & laying Second-Class Half-brick Masonry
(125 mm) in superstructure sq.m 476.05
5.0
5.1 700
Providing and laying in position plain cement concrete
(M10) - All works, excluding the cost of centering and
shuttering
cu.m 528.39
6.0
6.10 700
Providing and laying RCC M25 - All RCC Works
including up to Plinth, Column, Pillars, Post, struts, floor
beams, lintels, staircase, balconies excluding the cost of
centering, shuttering and reinforcement
cu.m 1,070.23
6.20 716
Bhutan type Traditional Cornices in M25 including cost
of formwork including finishing with 6mm thick plaster
on the exposed surface with cement mortar 1:3,
excluding reinforcement & decorative painting cost as
per standard design (Measurement to be taken along the
cornice and wall junction)
6.30 716 Lintel Cornice (only cornice portion at external face) m 145.66
6.40 716 At First floor level where Lhanglag is provided m 36.75
6.50 716 At First floor on rabsey top (excluding the cost of
phana) m 42.00
6.60 716 Phana - Rabsey top m 90.15
REINFORCED CEMENT CONCRETE WORK
PLAIN CEMENT CONCRETE WORK
Page 3 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
6.70 502
P/Laying in position reinforced cement concrete M40
(Rigid pavement) including provision of 125mm micron
thick impermeable plastic sheet, shuttering, dowel bars,
Tie bars, joint filler and curing compound - all work
upto finished level and compact with concrete vibrator
complete.
cu.m 1,241.08
7.0
7.1 900
Providing & fixing Thermo-Mechanically Treated
reinforcement bar (Yield Strength 500 MPa) for R.C.C
work including cutting, bending, binding and placing in
position complete - all RCC works
kg 109,482.25
8.0
8.1 800
Providing & fixing, centering and shuttering
(formwork), including strutting, propping etc. and
removal of formwork including Bhutanese architechural
drezhue and in All Works
sq.m 4,896.02
9.0
9.1 2412
Providing and laying moisture barrier using plastic
sheeting underlay - 200 micro-metre-polythene sheet
separation layer
sq.m 633.84
9.2 Standard Providing and laying Bitumen felt Type 3 in wall bases
etc.-Grade 2 sq.m 95.05
10.0
Providing & fixing in position Bhutanese window with
bhutanese archetraves in local hard wood including
frame, shutter 45mm veneered blockboard, fittings &
fixtures & hold fasts etc. with ekra design as per
drawing and specifications complete with all kinds of
polish and painting
Rabsel window Rw No. 10.00
10.1 1500
REINFORCEMENT
FORMWORK
DAMP PROOF COURSE
DOORS/WINDOWS/SHUTTERS
Page 4 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
10.2 1500
Providing and fixing in position the windows as per
drawing and specification provided, the rates must be
inclusive of specified material, transportation, all the
accessories such as shaft door lock with handle, hinges,
handle, tower bolt, sealer gasket, components, fittings,
4mm thk. glass, pelmet, etc. as per the drawing &
specification complete in all respect and as approved by
the Engineer. (Please refer the window Schedule to
understand the type and materials used in each window-
Hafele or equivalent)
ADM building
a W01 No. 12.00
b W02 No. 1.00
c V1 No. 1.00
d V2 No. 8.00
e V3 No. 3.00
f V4 No. 4.00
Service Building -
a W1 No. 7.00
b W2 No. 1.00
c V1 No. 2.00
d V2 No. 1.00
Public Toilet -
a V1 No. 12.00
b V2 No. 2.00
Security House -
a W No. 4.00
b V1 No. 1.00
Securiy Office Entry and Exit -
a W1 No. 2.00
b W2 No. 2.00
Siezed Goods Ware House
a W1 (steel window) No. 6.00
Control Room
a W1 No. 1.00
b W2 No. 1.00
Page 5 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
10.3 1500
Providing and fixing in position the doors as per
drawing and specification provided, the rates must be
inclusive of specified material, transportation, all the
accessories- hafele make or equivalent , accessories such
as shaft door lock with handle, hinges, handle, tower
bolt, sealer gasket, components, fittings, glass, etc. as per
the drawing & specification complete in all respect and
as approved by the Engineer(Please refer the Door
Schedule to understand the type and materials used in
each door )- Including door closer for Alumunium Doors
Administrative Bulding
a MD No. 1.00
b D01 No. 1.00
c D02 No. 5.00
d DAL No. 13.00
Service Building
a D1 No. 2.00
b D2 No. 1.00
c D3 No. 4.00
d Da1 No. 4.00
e Dw No. 1.00
f Aluminum Sliding Door No. 5.00
Public Toilet
a D1 No. 1.00
b D2 No. 11.00
Security House
a D1 No. 1.00
b D2 No. 2.00
Securiy Office Entry and Exit
a D1 No. 2.00
Siezed Goods Ware House
a D1 (steel door) No. 1.00
b Steel Rolling Shutter Rs No. 2.00
Control Room
a D1 No. 1.00
Page 6 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
11 CEILING WORKS
11.1 1400
Providing & fixing 8mm thick cement fibre board lining
in eave ceiling and ceiling of low roof including MS
angles and flats for fixing (as runners/ frames for false
ceiling), necessary screws etc. complete
sq.m 846.87
11.2 1400
Providing & fixing 6mm thick cement fibre board lining
in eave ceiling and ceiling of low roof including MS
angles and flats for fixing (as runners/ frames for false
ceiling), necessary screws etc. complete
sq.m 538.60
11.3 1400
Providing & fixing to frames (wall or ceiling) blue pine
plain lining, tongued and grooved, including MS angles
and flats for fixing, necessary necessary fixtures,
wooden plugs screws etc. complete including Prime Coat
sq.m 101.35
12
12.1 1000
Steel work welded, in built up sections, trusses, frame-
works including cutting, hoisting, fixing and appl.
priming coat of red lead paint (two coats) - square
hollow sections in roof structures as per drawing
kg 47,013.13
12.2 1000
Steel work welded, in built up sections, trusses, frame-
works including cutting, hoisting, fixing and apply
priming coat (two coats) of red In Tees, angles, flats,
hollow sections and channels
kg 17,745.57
12.3 1000 Providing & fixing M.S. round hold-down bolts with
nuts and washer plates as per drawing kg 209.01
12.4 1000 Providing & fixing bolts of various sizes including nuts
& washers kg 91.02
12.5 1500 Providing, fixing, anchoring and cutting of 25mm dia.
Plain bar as Rail-Mild steel bar kg 288.75
STEEL WORKS
Page 7 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
12.6 Standard Supplying and fiing of Roller and other accessories in
complete for three gates
Lum-
sum 3.00
12.7 1000
Providing and Fixing ornamental steel grills in frames
with MS flat and bars including round headed bolts and
nuts etc including Prime Coat and Alumunium Paint,
minumum two coats
kg 770.69
12.82006
&2007
Providing and fixing 600 mm dia concertina barbed
razer type coil of 19mm wide ribbon with thickness 5
SWG and central core wire of 12 SWG with antirust
coating / Galvanization as per manufacturer
specifications, supported over 6 rows of barbed wires of
14 SWG / Type II- conforming IS 278 and IS 4826,
fixed to Y shape angle bracket placed at 3.5m c/c of
50mmx50mmx6mm M.S.angle fixed in column. All
steel work including cutting, hoisting, fixing as Y Post
and applying priming coat of red lead oxide in angles (2
coats) complete as directed by Engineer-in-charge
m 530.00
13 ROOF WORKS
13.1 1300
Providing & fixing Pre Painted Galvanised Steel
Corrugated Roofing sheets, including bolts, hooks and
nuts 8mmdia. with bitumen and G.I limpet washers
filled with white lead for connection, excluding the cost
of purlins, rafter and trusses.-24G
sq.m 2,399.85
13.2 1300
Providing & fixing 600mm ridges or hips in Pre Painted
Galvanised Steel sheets, including bolts, hooks and nuts
8mm dia G.I limpet and bitumen washers for connection.-
24G
m 163.63
13.3 1300
Providing & fixing MS gutter as per the drawing,
including down pour pipe, bends, brackets, bolts, nuts,
washers & rain water pipes connections, including the
cost of pipes-complete
m 444.23
Page 8 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
13.4
Approve
d Brand
Providing & Fixing Turbo Ventilator including fibre
reinforced plastic base & all fixture items required as per
technical specifications.
No. 6.00
13.5 1000
Providing & fixing Eaves board (225x2mm) with
moulding fitted and fixed with necessary screws-MS
plate including red corrugal and enamel paint
m 369.62
14.0
14.1 1600
Providing & laying 40mm thick marble chips flooring
top layer 6mm thick with white, black or black and
white marble chips of nominal size 1.5-3mm in
proportion 1:2 (cement: chips), on 34mm thick concrete
base in cement concrete 1:2:4, 12.5mm
aggregate ( cement and marble powder mix shall be of
the ratio 3 part of cement to 1 part of marble powder) -
in grey Cement
sq.m 101.75
14.2 1600 Extra for Providing & fixing glass strips in joints of
terrazzo floors m 188.58
14.3 1600
Providing & fixing Terrazzo or Marble chips skirting <
300mm height top layer 6mm thick with white or black,
black and white marble chips size 4mm in proportion
1:2, laid on 12.5mm thick cement plaster 1:3 base - in
grey Cement
sq.m 23.71
14.4 1600
Providing & laying 20mm thick coloured marble stone
flooring over 20mm thick base of cement mortar 1:4,
jointed with grey cement slurry mixed with pigment
where necessary, rubbing & polishing complete in
staircase including landing and risers/ treads -width
<300mm
sq.m 299.48
14.5 1600 Providing & fixing Marble in skirting < 300mm height,
finished with flush-pointing in white cement-for wall m 130.00
FLOORING ASSOCIATED WORK
Page 9 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
14.6 1600
Providing and laying pre-polished/polished Granite of
approved quality and source in floor using necessary
cemt beding in cement motor in 1:4 up 20mm thick
average cement slurry for fixing the tiles with required
slopes, curing, cleaning,filiing the joints with pigment of
similar color and at levels with all leads and lifts
complete as per direction of site incharge and as per
pattern required and as per drawing (20mm thick
Granite stone for sitout and slab and Porch column
cladding) including nosing, complete in all respect
sq.m 38.83
15.0
15.1 1600
Providing & fixing 600mm x 600mm white/ coloured
glazed tiles in flooring, treads of steps and landings laid
on bed of 12mm thick cement mortar 1:3 finished with
flush pointing in white cement:
sq.m 549.24
15.2 1600
Providing & fixing 300 x 300mm white/ coloured
glazed antiskid floor tiles in toilet floor on bed of 20mm
thick cement mortar 1:3 finished with flush pointing in
white cement:
sq.m 209.94
15.3 1600
Providing & fixing 200x300 ceramic wall tile Dado in
alternate shades in toilet wall, finished with flush
pointing in white cement
sq.m 296.43
15.4 1600
Providing & fixing white/ coloured Glazed tiles, 150
mm high in skirting finished with flush pointing in white
cement
sq.m 108.44
16.0
16.1 1400 Providing & laying 20mm cement plaster-C.M 1:4 on
outer face of building including plinth height sq.m 1,155.05
16.2 1400 Providing & laying 15mm cement plaster 1:4 on all
inner wall faces half-brick walls sq.m 1,829.70
16.3 1400 Providing & laying 6 mm cement plaster-C.M 1:4 sq.m 550.08
16.4 1400 Providing & laying 20 mm cement motor band -C.M
1:4 (raised band for Ekra wall) sq.m 25.00
TILES WORK
PLASTERING WORK
Page 10 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
17
17.1 1700
Providing and applying Nerolac or equivalent excel total
all with Silicon base with one coat of primer as per
specification on External walls
sq.m 1,909.92
17.2 1700
Providing and applying finishing coats-Acrylic washable
distemper, two or more coats on new work, including
cement primer coat inside faces of building including
ceiling - same as plastering of all area and cement boards
on gable and eave ceiling
sq.m 2,258.56
17.3 1700
Providing and applying finishing coats: JK or
equivalent wall putty for internal plastered walls and
cement boards on gable and eave ceiling with minimum
3 coats and mix as per manufacture specification.
sqm 2,089.66
17.4 1700
Providing, preparing and applying Traditional Sumdang
painting (Not washable) - Rab- for all works as per
traditional requirement for buildings including all
Cornices, Ekra wall, Pillars, Gate post for whole
project
Lum-
Sum9.00
17.5 1700
Providing and applying high gloss synthetic enamel
paint on wooden surfaces two or more coats as per the
instruction of site engineer inclusive of Prime Coat.
sq.m 290.26
17.6 1700 Providing and applying finishing coats. Aluminium
paint, two coats on new Steel work sq.m 1,285.13
PAINTING WORK
Page 11 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
18
18.1 1500
Providing and fixing of 900mm high stainless steel
(Grade 304) railing made of Hollow tubes (50mm dia
handrail, 40mm dia balustrade and 20mm dia at
balustrade top and horrizontal runners) including
welding, grinding, buffing, polishing and making
curvature (wherever required) and fittings the same with
necessary stainless steel nuts and bolts complete, i/e
fixing railing with necessary accessories and stainless
steel dash fasteners, stainless steel bolts etc, of required
size on the top of the floor or the side of waist slab with
suitable arrangement as per detail drawing and approval
of engineers in charge.
m 13.39
18.2 1810
Providing & fixing 12mm thick Compact Laminate
Panel Partition (water proof) in toilets with frame and
fixtures of aluminium top rail, Stainless steel U-chanel
and Stain less steel adjustable foot including 12mm thick
Compact Cubicle Door (water proof) fitted with
Stainless steel cubicle Hinges, Stainless steel Door
Knob, Thumbturn WC Occupancy Indicator,etc.
complete as per detail drawing and approval of
engineers in charge.
sq.m 55.58
18.3 1500
Providing & fixing colour coated anodised aluminiun
sections in framing panelled with 6mm thick bothsides
prelaminated bison board and glazed with 4mm thick
clear glass including all accessories such as U-rubber
gasket for fixing glass and bison panels etc complete as
per detail drawing and approval of engineers in charge.
sq.m 476.44
ASSOCIATED ANCILLARY WORKS
Page 12 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
19
19.1 As per
Dwg.
Providing and laying 50mm thick Plinth Protection and
grouted with fine sand mix including well rammed,
finishing the top smooth-With cement concrete 1:3:6,
20mm aggregates, laid over 75mm thick layer of
compacted gravel (40mm) as per drawings
sq.m 344.45
19.2 As per
Dwg.
Constructing second class brick masonry open surface
drain in cement mortar 1:4 including earth work in
excavation, 100 mm thick concrete bed 1:5:10, 40mm
aggregate and 25mm thick cement concrete 1:2:4,12 mm
aggregate for filling haunches including 12mm cement
plastering 1:4 with a floating coat of neat cement and
disposal of surplus earth etc. complete-250mm x 300mm
depth as per drawings
m 335.81
20
20.1 1900
Providing & fixing P.V.C soil waste and vent pipes,
single or double socketed, including pipe clip complete
(excluding the cost 'of PVC fittings)
a 75mm dia m 77.31
b 110mm dia m 95.00
20.2 1900 Providing & fixing P.V.C soil waste and vent pipes
fittings
a PO0405 P.V.C plain bend - 75mm dia each 41.00
b PO0415 P.V.C door bend - 75mm dia each 27.00
c PO0475 P.V.C Single Y, plain - 75mm dia each 12.00
d PO0407 P.V.C plain bend - 110 mm dia each 46.00
e PO0417 P.V.C door bend - 110 mm dia each 21.00
f PO0477 P.V.C Single Y, plain - 110 mm dia each 10.00
g PO0507 P.V.C Double Y, with door - 110m dia each 9.00
PLUMBING and SEWERAGE WORK
PLINTH PROTECTION & DRAIN
Page 13 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
20.3 1800
Providing and fixing Chlorinated Polyvinyl
Chloride(CPVC) PN-16 Pipes, including all CPVC
plain and brass Threaded Polypropylene random fittings
including fixing pipe with clamps at 1.0m spacing. This
includes testing of joints, cutting chases and making
good the wall complete as per direction of Engineer-in-
Charge.
b PI0291 15mm dia m 127.32
c PI0292 25mm dia m 113.95
d PI0293 30mm dia m 35.00
20.4 1800
Providing & fixing European-type vitreous china w.c
pedestal including seat and lid with c.p brass hinges, 15
lit white vitreous china low level cistern, fittings,
brackets, repair walls-white, with plastic seat & lid-
jaquar make or equivalent.
No. 19.00
20.5 1800
Providing & fixing Indian-type vitreous china w.c
Squatting pane including food rest, 100mm scip or S-
trap, 10 lit white vitreous china low level cistern,
fittings, brackets, repair walls-white, 580mm White
Orissa Model or equivalent.
No. 5.00
20.6 1800
Providing & fixing white vitreous china flat back, lipped
front urinal basin 430x260x350mm including C.I cistern
& fittings, brackets, G.I. flush pipe & spreaders, brass
unions, G.I. clamps, painting, repair walls-One bowl-5
litres. C.I. cistern- jaquar make or equivalent.
No. 15.00
Page 14 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
20.7 1600
Providing and fixing pre-Polished/ Polished Granite of
approved quality and source as divider to urinals
including fixing to wall and finishing complete as per
the detail and directions of site in-charge
sq.m 10.31
20.8 1600
Providing & fixing white vitreous china wash basin,
including C.I brackets, 15mm C.P. brass pillar taps, c.p.
chain & rubber plug, 32mm pvc waste, 32mm dia. trap
& union, repair walls-Flat back wash basin 630x450mm
with a pair of 15mm c.p. brass pillar taps-jaquar make or
equivalent and superior quality mirror
No. 15.00
20.9 1600
Providing and fixing of Stainless Steel Kitchen Sink
940mmx 460mmx160mm single bowl and drain board
inclusive of waste water pipe and all fittings
No. 2.00
20.10 BSB Providing & fixing toilet paper holder-Recessed
ceramic, 200 x 100 mm, white No 24.00
20.11 BSB Providing & fixing c.p. towel rail 750 x 20mm with c.p
brass brackets fixed to wooden cleats No 13.00
20.12 BSB Providing & fixing soap dish-Recessed, ceramic,
200x100 mm-Jaquar make or Equivalent No 18.00
20.13 1800
Providing & fixing 600x450mm bevelled edge
mirror(superior glass) incl.4mm A.C sheet base fixed to
wooden cleats-Jaquar make or Equivalent
No 15.00
20.14 1800 Providing & fixing P.V.C Nahani Trap-110mm inlet &
75mm outlet-Jaquar make or Equivalent No 31.00
20.15 1800
Providing & fixing c.p. brass Combined bibcock with
standard vertical, c.p knob and Hand Shower with 1m
long flexible tube and hook as per specification
No 13.00
Page 15 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
20.16 1800 Providing & fixing c.p. brass bibcock 15mm with
standard vertical, c.p knob as per specification No 29.00
20.17 1800 Providing & fixing c.p. brass stop cock-15mm,
standard, c.p knob including all fittings and accessories No 43.00
20.18 1800 Providing & fixing plastic tank including all accessories
complete-2000 litre capacity No 2.00
20.19 1800 Providing & fixing plastic tank including all
connections and fittings complete-5000 litre capacity No 3.00
20.20 1900
Constructing Septic Tanks, in 2nd class brick masonry
in cement mortar 1:4, including fittings, C.I cover with
frame, 40mm thick concrete flooring (40mm aggregates)
cement plaster concrete base in C.C 1:4:8 etc. complete
as per standard design-75 users
No 3.00
20.21 1900
Constructing Septic Tanks, in 2nd class brick masonry
in cement mortar 1:4, including fittings, C.I cover with
frame, 40mm thick concrete flooring (40mm aggregates)
cement plaster concrete base in C.C 1:4:8 etc. complete
as per standard design-15 users
No 1.00
20.22 1900
Constructing Soak Pit-Size 2500 dia. x 3000mm depth
including 450x450mm dry brick honeycomb shaft and
SW drain pipe X 1800mm long
No 3.00
20.23 1900
Constructing Soak Pit-Size 1200 dia. x 1200mm depth
dry brick honeycomb shaft including SW drain pipe X
1200mm long
No 1.00
Page 16 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
20.24 As per
dwg
Constructing Brick masonry manhole in cement mortar
1:5, R.C.C top slab with 1:2:4 20mm aggregates,
foundation concrete 1:4:8 40mm aggregates, 12mm
plaster in CM 1:3 finished with floating coat of neat
cement and making channels in cement concrete 1:2:4
20mm aggregates, neatly finished complete: Inside
dimension 900 x 800mm & 600mm deep including C.I.
cover & frame (weight >38 kg)
No 10.00
20.25 1900
Providing and laying GI pipes including GI fittings
(Tees, bends, union) complets in all respect (excluding
trenching, refilling and thrust block) for External Water
Supply
-
a 50mm dia. m 1,800.00
b 25mm dia. m 184.00
b 20mm dia. m 35.00
d 15mm dia. m 40.00
21 OTHER WORKS/ ROAD WORKS
21.1 304
Preparation of sub grade with proper camber by
excavating earth to depth equal to pavement thickness,
consolidation with roller, disposal of surplus earth to any
lead and lifts. All kind of soils
sq.m 12,805.80
21.2 401
Providing and laying Granular sub-base course (GSB) to
required degree of compaction with proper formation of
cross fall using motor grader for laying and compacted
to required density as per material gradation and
aggregate quality specified
cu.m 2,775.61
Page 17 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
21.3 501
Providing and laying Dry Lean Concrete base including
providing coarse and fine aggregate to the specified
gradation using minimum cement content 150 kg/cum of
concrete with OPC 43 grade cement mixing of concrete
as per approved design mix and compacted with
mechanical means as directed by the Engineer-incharge.
cu.m 464.58
21.4 402
Providing and laying wet mix macadam graded
aggregate base course to required degree of compaction
with proper formation of cross fall by using well graded
crushed aggregates premixed with OMC using suitable
mixer, motor grader as per material gradation and a
aggregates quality specified
cu.m 2,250.30
21.5 503
Providing and laying 80mm thick strength type factory
made cement concrete interlocking paver block of M -40
grade made by block making machine with strong
vibratory compaction and of approved size and design /
shape laid in required colour and pattern over and
including filling of joints with fine sand etc. all complete
as per the direction of Engineer - in -charge
cu.m 626.08
21.6 2104
Providing and Laying Dense Bituminous Macadam (
DBM) to required degree of compaction based on
mixture design ( job mix formula) approved by the
supervising engineer including preparation of surface
with road broom, application of prime coat @ 0.75
kg/sq.m by mechanized method using asphalt plant,
paver, steel roller, tyre roller etc. complete 80mm
sq.m 360.00
21.7 2105
Providing and Laying Asphalt/Bituminous Concrete to
required degree of compaction based on the job mixture
design approved by the supervising engineer using
asphalt plant, paver, steel roller, tyre roller etc. as per
material gradation and aggregate quality specified 40mm
sq.m 360.00
Page 18 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
21.8 600
Providing and erecting direction and place identification
retro- reflectorised sign as per IRC:67 made of high
intensity grade sheeting vide clause 801.3, fixed over
aluminium sheeting of 2 mm thick supported on a mild
steel single angle iron post 75 x
75 x 6 mm firmly fixed to the ground by means of
properly designed foundation with M15 grade cement
concrete 45 x 45 x 60 cm, 60 cm below ground level as
per approved drawing and all complete as per Technical
Specifications and as directed by Engineer-Incharge.
Direction and Place Identification Signs upto 0.9
sqm Size
Board.
No 4.00
21.9As per
dwg.
Providing & fixing precast kilometre stone of RC 1:2:4
(20mm aggregate) including finishing with mortar 1:3
complete as per standard design (cost of excavation,
concreting, painting etc. shall be paid separately)
35cm x 111cm x 25cm
No 1.00
21.10 600
Providing and laying of hot applied thermoplastic
compound 2.5 mm thick including reflectorising glass
beads @ 250 gms per sqm area, thickness of 2.5 mm
is exclusive of surface applied glass beads as per
IRC:35 .The finished surface to be level, uniform and
free from streaks and holes all complete as per Technical
specification and as directed by the Engineer-in-charge.
sq.m 151.02
a Direction Arrows and Letters No 22.00
21.11 1700
Painting two coats on kerbs in black and white or yellow
after filling the surface with synthetic enamel paint
complete as per drawing and additional Technical
specifications clause A-2 and as directed by the Engineer-
in-charge.
sq.m 12.00
Page 19 of 20
Bill of Quantity _ALCS
Sl.No TS Ref. Description Unit Quantity Rate (Nu) Rate in words (Ngultrum) Amount
Project: Construction of Allay Land Custom Station (ALCS)
Contract No.: PT/CONTRACT/2019/ALCS/01
22 LANDSCAPING/BIOENGINEERING WORKS
22.10 2600
Turfing of embankment with 30 x 30 cm, natural grass
turfs and fixed to the ground with wooden pegs, if slope
is greater than 25°
sq.m 4,056.80
22.20 2600
Providing of Plants like Rose, different types of
greenery plants, flowers and ornamental plants etc.
complete or as directed by the Engineer-In-Charge.
No 200.00
23.00 EQUIPMENT
21.14 2700.1Supply and Testing of four wheeled Forklift including
the cost of Charging Station as per Specification No 1.00
21.15 2700.2Supply and Testing of Hydraulic Hand Pallet truck as
per the Specification No 2.00
21.16 2700.3
Supply, Installation, Comissioning and Testing of 80MT
Pitless Weigh bridge of size 18mx3m as per the
Specification no. 2700.3 including Computer, Licenced
Window (10) and interated Software, complete in all
respect including cost of foundation, ramp, duct and
other accessories, excluding the cost of Control Room.
No 1.00
21.17 2700.4
Supply, Installation, Comissioning and Testing of Boom
Barrier gate (Push Button Type) including all the
accessories required in complete in all respect (7m), as
per Specification
No 2.00
21.18 2201.11
Supply and Installation of Fire Extinguisher (CO2)
including cabinets for mounting and all other acessorries
as per specification
No 9.00
21.19 2201.11
Supply and Installation of Fire Extinguisher (Foam type)
including cabinets for mounting and all other acessorries
as per specification
No 6.00
Page 20 of 20
BOQ_ALCS_Electrical
A1
Provide & Draw Single Core 1.1KV grade PVC insulated
copper conductor cable in existing PVC/HDPE
surface/concealed conduit. Havels/HPL make or BSB Appd
equivalent brand.
A1.1 1x1.0 sq mm 1108 Mtr
A1.2 2x1.5 sq mm 3092.74 Mtr
A1.3 2x2.5 sq mm 2173.17 Mtr
A1.4 2x4.0 sq mm 1108 Mtr
A2
Wiring for sub-main with 1.1kV grade, PVC insulated copper
conductor cable in PVC surface conduit including connections,
painting, testing and commissioning etc. as required.
Havels/HPL make or BSB Appd equivalent brand.
A2.1 2x6 sq.mm 40 Mtr
A2.2 2x10 sq.mm 30 Mtr
A2.3 4x10 sq.mm 15 Mtr
A2.4 4x16 sq.mm 30 Mtr
A2.5 4x25 sq.mm 30 Mtr
A3
Supplying of 4- Core 1.1KV grade PVC insulated and sheathed
Aluminium conductor armoured power cables for main supply
from the Feeder Pillar to the respective Main Control Panel
Board. Havels/Polycab make or BSB Appd equivalent brand.
A3.1 16 sq.mm (from feeder to MCPB) 120 Mtr
Contract No.: PT/CONTRACT/2019/ALCS/01
Rate in Words
BILL OF QUANTITIES (Electrical Works)
Sl. No Description of Item Qty Unit Rate (Nu.) Amount (Nu.)
A . WIRING
Project: Construction of Allay Land Custom Station (ALCS)
Page 1 of 15
BOQ_ALCS_Electrical
A3.1 50 sq.mm (from feeder to MCPB) 65 Mtr
A3.1 95 sq.mm (from feeder to MCPB) 60 Mtr
A4
Laying of one number PVC insulated and sheathed power cable
copper /aluminium, armoured/un-armoured 1.1KV single core
to four core direct in the ground including excavation, sand
cushing, protective covering and refilling the trenches etc. as
required
A4.1 Above 6sq.mm to 25sq.mm 120 Mtr
A4.2 Above 25sq.mm to 70sq.mm 65 Mtr
A4.3 Above 70sq.mm to 150sq.mm 65 Mtr
SUB-TOTAL for WIRING -
B.1
Supplying of ceiling fan 240 volt A.C 1400 rpm with all
accessories such as down rod, sweep 3 Nos.,canopy 2 Nos.,
condenser and fan body etc. complete as required - 1200mm
sweep (BSB approved brand)
41 Each
B.2
Supplying of exhaust fan 240 volt A.C 1400 rpm with louvers
and all accessories such as frame with arm 3 Nos., sweep 3
Nos., condenser and fan body etc. complete as
required - 300mm sweep
5 Each
B.3
Supplying of slim surface mounted round LED panel lamps,
aluminium die cast body with premium diffuser to ensure glare
free and even distribution of light and with replaceable
electronic driver and other complete accessories as required.
LHEAAVP61W012 (HSN code 9405)
78 Each
B. FITTINGS AND ACCESSORIES
Page 2 of 15
BOQ_ALCS_Electrical
B.4
Supplying and Fixing of Diffused LED Panel Light with
electronic drivers (15W LED LHEBLDP5IN1W015), -Endura
Slim Pro Plus and edge-lit luminaire suitable for false ceiling.
Cat No/HSN code - 9405 complete as required.
Havels/HPL/Jaquar make or BSB Appd equivalent brand.
61 Each
B.5
Supplying and Fixing of high bay LED electra slim tubelight
with electronic ballast and other necessary fittings suitable
for T8 FTL, Cat No. LHDF14104025, 2x36 complete
accessories as required. (Havels or BSB Appd equivalent
brand)
20 Each
B.6
Supplying of 150W LED flood light (IP rating IP66) with
aluminium die casting body, toughened glass, Silicon Rubber
Gasket, electronic driver and other complete accessories as
required
3 Each
B.715W LED bulb with bulkhead of plastic body and other
complete accessories as required. (HLPLEDBH10) 4 Each
B.8
High mask 400W LED lamps for Parking with high premum
diffuser and replaceble electronic driver suitable to install for
18m high pole with all other complete accessories as required
(BSB approved brand- Product and installation verification
will be done by enginer concerned at site .)
5 Each
B.9
100W round shaped LED street light (QC32-LH), of either
ceramic, copper, aluminium and body casing of aluminium
casting powder coated with premium diffuser, replaceble
electronic driver and complete accessories as required (BSB
approved brand)
30 Each
Page 3 of 15
BOQ_ALCS_Electrical
B.10
Supplying and fixing of LED 100W IP55, acrylic globe top
post lamp for Gate with aluminium die cast body, Corrosion
and UV Ray resistant coating, high premium diffuser and
replacable electronic driver and other complete accessories as
required. (BSB approved brand)
4 Each
B.11
Supplying and fixing 30W LED acrylic Globe Post Top Lamp
for compound light infront of buildings, having plastic and
aluminium die cast body with matt finish, IP rating (IP55)
with high premium diffuser and replaceable electronic driver
and other complete accessories as required. (BSB approved
brand)
11 Each
SUB-TOTAL for FITTINGS AND ACCESSORIES -
C1
Supplying & fixing of metal boxes & front plate with inner base
frame for switch/socket outlet/switch socket combined/ gang
switches on surface/embedd including painting etc complete as
required. Havels/HPL/Panasonic make or BSB Appd equivalent
brand.
C1.1 1 Module 8 Each
C1.2 2 Module 11 Each
C1.3 3 Module 21 Each
C1.4 4 Module 12 Each
C1.5 5 & 6 Module 12 Each
C2
Supplying & fixing of switch/socketon existing PVC/metal /
moulded tough surface box (recessed or surface) including
necessary cutting, connection testing etc. as required.
Havels/HPL/Panasonic make or BSB Appd equivalent brand.
C2.1 6A or 10A switch SP 1-way 219 Each
C. SWITCH AND SOCKETS
Page 4 of 15
BOQ_ALCS_Electrical
C2.2 16A switch SP 1-way with indicator 70 Each
C2.3 5/6 pin, 16A socket outlet, shuttered 70 Each
C2.4 Ceiling Rose 125 Each
C3
Supplying & fixing of 6A switch/socket on existing PVC
/metal/ moulded tough surface box metal box (recessed or
surface) with fibre sheet cover (recessed or surface) including
necessary cutting, connection testing etc. as required.
C3.1 3-pin 6A switch/socket combined, shuttered 3 Each
SUB-TOTAL for SWITCH AND SOCKETS -
D1
Design, fabrication, providing, erection, connection, testing &
commissioning of cubical indoor, floor mounting type, (Indoor
type) L.T Panel Boards as per the provided drawings -minimum
50x50x6mm angle iron frame work with horizontal and vertical
intermidiate members of GI flat iron 40x6mm and 12SWG
sheet cover with gasket for mounting of switch gears, incoming/
outgoing bus bar chambers including drilling holes, painting,
denting, grouting etc. as required. The panel should have a set
of 800/5A, 15 VA CT, Voltmeter & Ammeter with Selector
switch, indicating lamp, Danger plate and other necessary
control gears as required for LT panel. Built by reputed panel
manufacturer of sizes Width upto 2500mm x Depth 500mm-
1000mm Maximum and Height upto1500mm at the proposed
location. (Actual size of panel should be confirmed with the
actual space available at site upon construction).
4 Each
D. SUB MAINS, SWITCHGEARS & BUSBAR
Page 5 of 15
BOQ_ALCS_Electrical
D2
Supplying and Fixing of Incoming/Outgoing MCCB/MCB of
the following sizes/rating for respective MCPB complete with
all accessories including connection, testing, commissioning,
ferruling etc as required. All cabling and terminations should be
properly and neatly done and arranged in cable alley with
suitable size cable.
D2.1
4P-250 Amps Moulded Case Circuit Breakers (MCCB) with
thermal magnetic and microprocessor release, breaking
capacity 70KA, 415V (Incoming (MCPB 1 )
1 Each
D2.2
4P-125 Amps Moulded Case Circuit Breakers (MCCB) with
thermal magnetic and microprocessor release, breaking
capacity 36/50KA, 415V (Incoming (MCPB 2 )
1 Each
D3.3
Supplying of panel moulded case circuit breaker (MCCB) with
electronic release, breaking capacity 16KA, 4 pole 415 volt A.C
complete with all accessories
etc. as required - 63A (MCPB 3 & 4 )
2 Each
Outgoing (MCPB)
D3.i 4P 40 Amps MCB, 10kA, with electronic release 1 Each
D3.ii 4P 63 Amps MCB, 10kA, with electronic release 2 Each
D3.ii 4P 100 Amps MCB, 10kA, with electronic release 3 Each
D4
Supplying of Aluminium alloy/wrought aluminium busbar
complete with all accessories etc. to accommodate in
prefabricated MS Cubical panel board as required.
D4.1 4 strips, 600mm bar, 300A 2 Each
D4.2 4 strips, 600mm bar, 100A 2 Each
D5
Supply of SPN distribution board (DIN type) with metal door,
230 volt A.C complete with all accessories without
MCB/isolator/RCCB out going or incoming etc. as required.
Havels/HPL/Legrand make or BSB Appd equivalent brand.
D5.1 4 ways 4 Each
Page 6 of 15
BOQ_ALCS_Electrical
D5.2 6 ways 2 Each
D5.3 8 ways 1 Each
D6
Supply of TPN distribution board (DIN type, horizontal)with
metal door, 415 volt A.C complete with all accessories without
MCB/isolator/RCCB out going
or incoming etc. as required. Havels/HPL/Legrand make or
BSB Appd equivalent brand.
D6.1 12ways 2 Each
D7
Supply of residual current circuit breaker (RCCB) double pole,
sensitivity 100mA, 230 volt A.C complete with all accessories
suitable to to fix on a din-bar etc. as required.
Havels/HPL/Legrand make or BSB Appd equivalent brand.
D7.1 16A 2 Each
D7.2 25A 1 Each
D7.3 63A 3 Each
D8
Supply of residual current circuit breaker (RCCB) 4 pole,
sensitivity 100mA, 415 volt A.C complete with all accessories
suitable to to fix on a din-bar etc. as required.
Havels/HPL/Legrand make or BSB Appd equivalent brand.
D8.1 63A 3 Each
D8.2 100A 2 Each
D9
Supply of miniature circuit breaker (MCB) single pole, 230 volt
A.C complete with all accessories suitable to fix on a din-bar
etc. as required. Havels/HPL/Legrand make or BSB Appd
equivalent brand.
D9.1 10A SP MCB C-type 68 Each
D9.2 16A SP MCB C-type 94 Each
D9.3 32A SP MCB C-type 1 Each
Page 7 of 15
BOQ_ALCS_Electrical
D10 Energy Meter
D10.1
Purchasing and installation of 1 Phase and 2 Wires Energy
Meter from BPCL including required CT coils and connection
wires etc complete a required for Energy Meter work.
4 Each
D10.2
Purchasing and installation of 3 Phase and 4 Wires Energy
Meter from BPCL including required CT coils and connection
wires etc complete a required for Energy Meter work.
3 Each
SUB-TOTAL for SUB MAINS, SWITCHGEARS &
BUSBAR-
E1
Supplying and fixing of PVC/HDPE conduit on
surface/concealed (which ever applicable as per type of ceiling)
including all accessories such as screws, bends,elbows, Tees,
corners, etc. complete as required for all type of wiring in false
ceiling.
E1.1 20mm 125 Mtr
E1.2 25mm 150 Mtr
E2
Supplying and fixing of PVC casing & capping on surface
including cup washer, screws, bends, elbows,Tees, corners, etc.
complete as required
E2.1 25x10x1.2mm 300 Mtr
E2.2 20x12x1.2mm 200 Mtr
E3
Supplying and fixing of recessed MS conduit including all
accessories such as screws, bends, elbows,Tees, corners, etc.
complete as required (Underground conduit for campus and
street lighting)
E3.1 25mm 350 Mtr
E. PVC CONDUIT/HDPE PIPES & ACCESSORIES
Page 8 of 15
BOQ_ALCS_Electrical
E4
Providing & laying H.D.P.E Pipes, 6 PN, including H.D.P.E
fittings (excluding trenching, refilling & thrust block - for road
crossing at entry and exit gate)
25 Mtr
E4.1 75mm
SUB-TOTAL of PVC CONDUIT/HDPE PIPES &
ACCESSORIES
F1
Installation, testing and commissioning of all size ceiling fan
and regulator including wiring the down rod of standard length
upto 300mm with PVC
insulated copper conductor - 1.5 sq.mm single core cable 1.1
KV grade
41 Each
F2
Installation, testing and commissioning of exhaust fan upto
450mm sweep the existing opening including making the hole
to suit the size of the indicated fan
making good the damages, and connection with PVC insulated
copper conductor -1.5 sq.mm single core cable 1.1 KV grade
5 Each
F3
Erection of all indoor surface/recessed type LED ceiling
fittings, and wall fittings with fixing of lamp, testing etc. as
required including connection with PVC insulated copper
conductor and other associated works.
F3.1 1.5 sq.mm single core cable 1.1 KV grade 160 Each
F4
Installation, testing and commissioning of four pole moulded
case circuit breaker (DIN type) breaking capacity
16/25/36K/earth leakage module complete
with all accessories to accommodate on/in prefabricated MS
surface /MS cubical control panel board including drilling
holes, connections etc as required
F4.1 63A, 415V 2 Each
F. ERECTION / INSTALLATION
Page 9 of 15
BOQ_ALCS_Electrical
F4.2 125A, 415V 1 Each
F4.3 250A, 415V 1 Each
F5
Installation, testing and commissioning of TP miniature circuit/
isolator breaker complete with all accessories to accommodate
on/in prefabricated MS
surface/MS cubical control panel board including drilling holes,
connections etc as required
F5.1 40A, 415V 2 Each
F6
Installation, testing and commissioning of SPN/DP-
MCB/RCCB (DIN type) complete with all accessories to
accommodate on/in prefabricated MS surface /MS cubical
control panel board including drilling holes, connections etc as
required
F6.1 6/10/16/20 Amps 168 Each
F6.2 50/63A 4 Each
F7
Installation, testing and commissioning of four pole moulded
case circuit breaker (DIN type) breaking capacity
16/25/36K/earth leakage module complete
with all accessories to accommodate on/in prefabricated MS
surface /MS cubical control panel board including drilling
holes, connections etc as required
F7.1 100A, 415V 6
F8
Installation, testing and commissioning of SPN DB (DIN type,
horizontal/ Vertical) with matellic door complete with all
accessories to accommodate incoming RCCBs/MCBs and
outgoing SP MCB 6/10/16A.
F8.1 4 ways 4 Each
F8.2 6 & 8 ways 3 Each
Page 10 of 15
BOQ_ALCS_Electrical
F9
Installation, testing and commissioning of TPN DB (DIN type,
horizontal/vertical) with no door, metal door or arcylic door
(double/single door) complete
with all accessories to accommodate incoming
RCCB/ELCB/RCBO FP 125A sensitivity 30/100/300mA and
outgoing SP MCB 6/10/16A on/in
prefabricated MS surface /MS cubical control panel board
including drilling holes, connections etc. as required.
F9.1 12 ways 2 Each
F10
Installation, testing & commissioning of aluminium
alloy/wrought aluminium bus bar complete with all accessories
accessories to accomodate in prefabricated MS cubical control
panel board including connections etc. as required
F10.1 4 strips, 600mm length, 100A 2 Each
F10.2 4 strips, 600mm length, 300A 2 Each
SUB-TOTAL for ERECTION / INSTALLATION
G1
Supplying & fixing of metal boxes & front plate with inner base
frame for TV/RJ11/RJ45 outlet on surface/embedd including
painting etc complete as required. Havels/HPL/Panasonic make
or BSB Appd equivalent brand.
G1.1 1 Module 32 Each
G1.2 2 Module 4 Each
G1.3 3 Module 4 Each
G1.4 4 Module 2 Each
G. SUPPLY & FIXING OF DATA POINT
Page 11 of 15
BOQ_ALCS_Electrical
G2
Supplying & fixing of socket outlet on existing PVC /metal/
moulded tough surface box/ metal box (recessed or surface)
including necessary cutting, connection testing etc. as required.
Havels/HPL/Panasonic make or BSB Appd equivalent brand.
G2.1 RJ 45 Socket 42 Each
G3
Provide and draw Network cable/ high density polythene
insulated & sheathed copper conductor 0.5mm dia telephone
wire/RG6 video cable in existing surface/ recessed conduit
wiring system complete as required. Havels/HPL/Achor make
or BSB Appd equivalent brand.
G3.1 CAT 6a Network Cable 1250 Mtr
SUB-TOTAL FOR SUPPLY & FIXING OF DATA POINT
H1
Providing and installation of water pump, Model KDS 335++
3HP Centrifugal Water Pump 415v AC, Head (Mtrs) : 9 Mtrs
including wiring with 2x6 sq mm PVC insulated copper wire,
DOL starter (20A), 2P MCB 25 A, MCB DB complete as
required at site.
1 Each
SUB-TOTAL FOR SUPPLY & FIXING OF WATER
PUMP MOTOR
I1 Providing & fixing of Air Conditioners - 1 tonne, split type 21.00 Each
SUB-TOTAL FOR SUPPLY & FIXING OF AIR
CONDITIONER
H. SUPPLYING AND FIXING OF WATER PUMP MOTOR
I. AIR CONDITIONER
Page 12 of 15
BOQ_ALCS_Electrical
J1
Supplying and fixing of High Mast pole (M.S/G.I Material) of
18m high ( shape- Polygonal, Dia of Pole Bottom - 410mm .
Top - 150mm, base plate-540mm dia with 25mm thickn,
8nos of 20mm dia anchor bolt with 75mm long,nuts, etc.)
with five numbers of arm/suspnsion of 1 meter length and all
other complete accessorie required for installation. The
supplied pole should also be approved by BSB. (Need to
consult concern engineer for product verfication at site)
1 Each
J2
Supplying of compound light steel tubular pole 50/60mm outer
dia having a base plate 250x250x5.4mm, entry hole of 20mm
dia 1.1m from bottom and strude bolt as earth terminal
complete as required ( Re-fabrication should be done at site if
required as per design and site condition)
J2.1 5.5m, 5.4mm thick 41 Each
J3
Supplying of junction box fabricated with 14SWG MS sheet,
removal cover plate with gasket for dust and vermine proof, 2
earthing terminals with nut, bolts and spring washer, 2 entry
holes 16mm dia at bottom, 32mm dia for cable entry at back ,
including 4 way terminal block & HRC fuse unit with fuse of
6A with locking arrangement and finish coat painting complete
with all accessories as required as per standard drawing
J3.1 MS junction box out door duty 42 Each
Supply of electronic timer switch double pole, 50Hz, sensitivity
30mA, 230 volt A.C complete with all accessories suitable to to
fix on a din-bar etc. as required
7days/24hrs 2 Each
J . CAMPUS LIGHTING
Page 13 of 15
BOQ_ALCS_Electrical
J4
Erection of compound light steel tubular pole 5.5m length
50/60mm dia. with 20mm dia MS sleeve as inlet of power cable
in cement concrete 1:3:6, 40mm
stone aggregate foundation with cement concrete base
0.47mx0.47mx75mm thick 1:4:8 including excavation,
centering & shuttering, and refilling,
providing props for pole etc. complete as required
J4.1 At dead end 5 Each
J4.2 At middle 25 Each
J5
Erection of junction box and pole cap with arm including
wiring with PVC insulated copper conductor cable 1.1KV grade
2x2.5sq.mm through the existing pole & arm bracket from
junction box including erection of street light fixtures, lamps,
connection, testing etc. complete as required
J5.1 Post top lamp fixtures 42 Each
J6
Installation, testing and commissioning of DP timer switch
assembly in a case complete with all accessories to
accommodate on/in prefabricaetd MS surface/MS cubical
control panel board recessed including drilling holes,
connections etc as required -
J6.1 Adjustment range either 24/24hrs or 7days/24hrs 2 Each
SUB-TOTAL for CAMPUS LIGHTING, POLES &
ACCESSORIES
K
Providing and fixing of earthing including all accessories,
machinery enclosure, C.I cover plate having locking
arrangement, watering pipe with excavation and refilling work
including charcoal or coke and salt complete as required as per
standard earthing drawing
K1 With copper earth plate 600x600x3mm 11 Each
K. EARTHING & LIGHTNING PROTECTION
Page 14 of 15
BOQ_ALCS_Electrical
K2
Providing and laying earth connection from earth electrodes in
15mm dia G.I pipe as required as per standard earthing
drawing. From earth electrode to respective panel board.
K2.1 With 4.06mm dia (8 SWG) G.I wire 550 Mtr
K3
Providing and drawing wire for loop earthing in existing
surface/recessed PVC/MS/ steel conduit or casing caping or
wooden batten along with other wires as required.
K3.1 2.032mm (14 SWG) copper wire 500 Mtr
K4
Providing and fixing of lightning conductor including holes and
spring washer etc. riveting, sweating and soldering complete as
required.
K4.125mm dia 900mm long copper tube having four prong at top
with 85mm dia 3mm thick copper base plate.4 Each
K4.2 Copper tape with another copper tape 4 Each
K5
Providing and fixing metal strip on parapet or surface of
wall/roof for lightning conductor as required with 25x4mm
copper strip.
K5.1 Horizontal Run 120 Mtr
K5.2 Vertical Run 120 Mtr
K6
Providing and installation of street/compound light pole
earthing including connections, testing etc. complete as
required including excavation and refilling
K6.1 With G.I earth spike 1.8mtr 42 Each
SUB-TOTAL for EARTNG & LIGHT PROTECTION
L.1
Supply, Installation, Comissioning and Testing of 250 KVA
Diesel Generator (Silent Type- Out door) including Auto
Transfer switch with panel board including the cost of
construction of Platform to rest the Generator
TOTAL
Page 15 of 15