Upload
phamhuong
View
226
Download
1
Embed Size (px)
Citation preview
Netzteile
Katalog 08-2016
Technische Änderungen, Fehler und Irrtümer vorbehalten! OTT GmbH & Co. KG ● 78652 Deißlingen ● Tel.: 07420-9399-0 ● Fax.: 07420-9399-25 ● Email: [email protected]
Übersicht Schaltnetzteile Serie AKL... Diese Schaltnetzteile sind gut geeignet für induktive Lasten wie zum Beispiel DC-Motoren.
Artikelnummer Ausgangsspannung Nennstrom Nennleistung Eingangsspannungsbereich
( VDC ) ( A ) ( W ) ( VAC )
AKL10001-01 24 1,5 36 88-264
AKL10002-01 24 2 48 85-264
AKL10003-01 24 2,5 60 88-264
AKL10004-00 12 6,3 76 85-264
AKL10004-01 24 3,2 76,8 85-264
AKL10004-02 48 1,6 76,8 85-264
AKL10005-01 24 5 120 88-132/176-264 (umschaltbar)
AKL10006-01 24 10 240 85-264
AKL10007-01 24 20 480 180-264
AKL10007-02 48 10 480 180-264
AKL10008-01 24 10 240 340-550 (Dreiphasen)
AKL10008-02 48 5 240 340-550 (Dreiphasen)
AKL10009-01 24 20 480 340-550 (Dreiphasen)
AKL10009-02 48 10 480 340-550 (Dreiphasen)
AKL10010-01 24 40 960 340-550 (Dreiphasen)
AKL10010-02 48 20 960 340-550 (Dreiphasen)
AKL10011-01 5 6 30 85-264
AKL10011-02 12 3,33 40 85-264
AKL10011-03 24 1,7 40,8 85-264
AKL10011-04 48 0,83 39,8 85-264 Weitere Schaltnetzteile auf Anfrage.
Schaltnetzteil 1-phasig
- voller AC-Eingangsbereich- auf DIN-Schiene TS35/7,5 oder 15 montierbar- langlebig- hohe Leistungsfähigkeit, geringe Betriebstemperatur- eingebauter Entstörfilter, geringe Restwelligkeit- LED - Anzeige- kompakte Größe, Leicht- 100% Burn-In Test unter Volllast- Kurzschluss- / Überlast- / Überspannungsschutz- ohne Lüfter- Zulassungen: UL/TUV/CE- Sicherheit: UL60950-1, TUV EN 60950-1- EMV:
AKL10001-01
Ausgangsspannung [VDC] 24
Einstellbereich der Ausgangsspannung [VDC] 21,6 - 26,4
Nennstrom [A] 1,5
Nennleistung [W] 36
Restwelligkeit (max.) [mVss] 150
Spannungstoleranz [%] +/- 1
Netzausfallüberbrückung (typ.)
Eingangsspannungsbereich
Frequenzbereich [Hz] 47 - 63
Wirkungsgrad (typ.) [%] 83
Stromaufnahme (typ.)
Einschaltstossstrom (typ.)
Überlast
Überspannung [VDC] 27,6 - 32,4
Übertemperatur [°C] 90 +/-5
Umgebungstemperatur (Betrieb) [°C]
Luftfeuchtigkeit (Betrieb)
Umgebungstemperatur (Lagerung) [°C]
Vibration
Isolationsspannung [VAC]
Isolationswiderstand
MTBF
Abmessungen (A, B, C) [mm] 78 x 93 x 56 (B X H X T)
Gewicht [kg] 0,27
EN550011, EN55022 Klasse B, EN61000-3-2,3,EN61000-6-2, EN61000-4-2,3,4,5,6,8,11, ENV50204EN55024, EN61204-3
Artikelnummer
100ms / 230VAC 21ms / 115VAC (bei Nennstorm)
88 - 264VAC 124 - 370VDC
Eingang
0,88A / 115VAC 0,48A / 230VAC
Kaltstart 15A / 115VAC 30A / 230VAC
Ausgang
Schutz-funktionen
Abschaltung der Ausgangsspannung . Neustart mit Wegnahme der Primärspannung
20 - 90%, nicht kondensierend
-20 - +60
105 -160% über NennlastStrombgrenzung, wird automatisch zurückgesetzt
-40 - +85 10 - 95% rel. Luftfeuchtigkeit
10 - 500Hz, 2G, 10min./1Zyklus, 60 Min. X,Y,Z-Achsen
AllgemeineDaten
Eingang/Ausgang: 3k
100MOhm / 500VDC
441,5k Stunden min. MIL-HDBK-217F (25°C)
Umgebung
Datenblatt
OTT GmbH & Co. KG ● D-78652 Deißlingen ● Tel.: +49 (0)7420-9399-0 ● Fax.: +49 (0)7420-9399-25 ● Email: [email protected]
Blockschaltbild
Leistungsherabsetzung
M e c h a n i s c h e E i g e n s c h a f t e n Maßeinheit: mm
date: 13-02-2007
-2 0 0 10 20 30 40 5 0 6 0 70
20
40
60
80
100
Umgebungstemeratur (°C)
Bel
astb
arke
it (
%)
Terminal PIN Nr. ZuordnungPin No. Pin No.
2
1 5,6
3,4
7
8
Assignment Assignment
+V
AC/N
AC/L
-V
LED
+VADJ.
Zulässige Befestigungsschiene: TS35/7.5 oder TS35/15
93
655
55
5
34
2
37
.75
1
78
12
.2
7
8
45
68
46.5
27
.4
3
47
56
46.5
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCH-
FILTER
&
RECTIFIERS +V
-VI/P
ING
CONTROL
O.V.P.
Eingangsspannung (VAC) 60Hz
85 10095 120115 160140 200180 240220 264
Bel
astb
arke
it (
%)
Ta=25
90
100
80
70
60
50
40
35
Gehäuse Nr. 918B
Leistungsherabsetzung in Abhängikeit der Eingangsspannung
Datenblatt
OTT GmbH & Co. KG ● 78652 Deißlingen ● Tel.: 07420-9399-0 ● Fax.: 07420-9399-25 ● Email: [email protected]
Schaltnetzteil 1-phasig
- voller AC-Eingangsbereich- auf DIN-Schiene TS35/7,5 oder 15 montierbar- langlebig- hohe Leistungsfähigkeit, geringe Betriebstemperatur- eingebauter Entstörfilter, geringe Restwelligkeit- LED - Anzeige- kompakte Größe, Leicht- 100% Burn-In Test unter Volllast- Kurzschluss- / Überlast- / Überspannungsschutz- ohne Lüfter- Zulassungen: UL/TUV/CE- Sicherheit: UL508, UL60950-1, TUV EN 60950-1- EMV:
AKL10002-01
Ausgangsspannung [VDC] 24
Einstellbereich der Ausgangsspannung [VDC] 21,6 - 26,4
Nennstrom [A] 2,0
Nennleistung [W] 48
Restwelligkeit (max.) [mVss]
Spannungstoleranz [%] +/- 1
Netzausfallüberbrückung (typ.)
Eingangsspannungsbereich
Frequenzbereich [Hz] 47 - 63
Wirkungsgrad (typ.) [%] 83
Stromaufnahme (typ.)
Einschaltstossstrom (typ.)
Überlast
Überspannung [VDC] 27,6 - 32,4
Übertemperatur [°C] 90 +/-5
Umgebungstemperatur (Betrieb) [°C]
Luftfeuchtigkeit (Betrieb)
Umgebungstemperatur (Lagerung) [°C]
Vibration
Isolationsspannung [VAC]
Isolationswiderstand
MTBF
Abmessungen (A, B, C) [mm] 78 x 93 x 56 (B X H X T)
Gewicht [kg] 0,27
EN550011, EN55022 Klasse B, EN61000-3-2,3,EN61000-6-2, EN61000-4-2,3,4,5,6,8,11, ENV50204EN55024, EN61204-3
Artikelnummer
100ms / 230VAC 21ms / 115VAC (bei Nennstorm)
85 - 264VAC 120 - 370VDC
Eingang
0,88A / 115VAC 0,48A / 230VAC
Kaltstart 15A / 115VAC 30A / 230VAC
Ausgang
Schutz-funktionen
Abschaltung der Ausgangsspannung . Neustart mit Wegnahme der Primärspannung
20 - 90%, nicht kondensierend
-20 - +60
105 -160% über NennlastStrombgrenzung, wird automatisch zurückgesetzt
-40 - +85 10 - 95% rel. Luftfeuchtigkeit
10 - 500Hz, 2G, 10min./1Zyklus, 60 Min. X,Y,Z-Achsen
AllgemeineDaten
Eingang/Ausgang: 3k
100MOhm / 500VDC
441,5k Stunden min. MIL-HDBK-217F (25°C)
Umgebung
Datenblatt
OTT GmbH & Co. KG ● D-78652 Deißlingen ● Tel.: +49 (0)7420-9399-0 ● Fax.: +49 (0)7420-9399-25 ● Email: [email protected]
Blockschaltbild
Leistungsherabsetzung
M e c h a n i s c h e E i g e n s c h a f t e n Maßeinheit: mm
date: 13-02-2007
-2 0 0 10 20 30 40 5 0 6 0 70
20
40
60
80
100
Umgebungstemeratur (°C)
Bel
astb
arke
it (
%)
Terminal PIN Nr. ZuordnungPin No. Pin No.
2
1 5,6
3,4
7
8
Assignment Assignment
+V
AC/N
AC/L
-V
LED
+VADJ.
Zulässige Befestigungsschiene: TS35/7.5 oder TS35/15
93
655
55
5
34
2
37
.75
1
78
12
.2
7
8
45
68
46.5
27
.4
3
47
56
46.5
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCH-
FILTER
&
RECTIFIERS +V
-VI/P
ING
CONTROL
O.V.P.
Eingangsspannung (VAC) 60Hz
85 10095 120115 160140 200180 240220 264
Bel
astb
arke
it (
%)
Ta=25
90
100
80
70
60
50
40
35
Gehäuse Nr. 918B
Leistungsherabsetzung in Abhängikeit der Eingangsspannung
Datenblatt
OTT GmbH & Co. KG ● 78652 Deißlingen ● Tel.: 07420-9399-0 ● Fax.: 07420-9399-25 ● Email: [email protected]
Schaltnetzteil 1-phasig
- voller AC-Eingangsbereich- auf DIN-Schiene TS35/7,5 oder 15 montierbar- langlebig- hohe Leistungsfähigkeit, geringe Betriebstemperatur- eingebauter Entstörfilter, geringe Restwelligkeit- LED - Anzeige- kompakte Größe, Leicht- 100% Burn-In Test unter Volllast- Kurzschluss- / Überlast- / Überspannungsschutz- ohne Lüfter- Zulassungen: UL/TUV/CE- Sicherheit: UL508, UL60950-1, TUV EN 60950-1- EMV:
AKL10003-01
Ausgangsspannung [VDC] 24
Einstellbereich der Ausgangsspannung [VDC] 21,6 - 26,4
Nennstrom [A] 2,5
Nennleistung [W] 60
Restwelligkeit (max.) [mVss] 150
Spannungstoleranz [%] +/- 1
Netzausfallüberbrückung (typ.)
Eingangsspannungsbereich
Frequenzbereich [Hz] 47 - 63
Wirkungsgrad (typ.) [%] 84
Stromaufnahme (typ.)
Einschaltstossstrom (typ.)
Überlast
Überspannung [VDC] 27,6 - 32,4
Übertemperatur [°C] 90 +/-5
Umgebungstemperatur (Betrieb) [°C]
Luftfeuchtigkeit (Betrieb)
Umgebungstemperatur (Lagerung) [°C]
Vibration
Isolationsspannung [VAC]
Isolationswiderstand
MTBF
Abmessungen (A, B, C) [mm] 78 x 93 x 56 (B X H X T)
Gewicht [kg] 0,3
EN550011, EN55022 Klasse B, EN61000-3-2,3,EN61000-6-2, EN61000-4-2,3,4,5,6,8,11, ENV50204EN55024, EN61204-3
Artikelnummer
100ms / 230VAC 32ms / 115VAC (bei Nennstorm)
88 - 264VAC 124 - 370VDC
Eingang
1,2A / 115VAC 0,8A / 230VAC
Kaltstart 18A / 115VAC 36A / 230VAC
Ausgang
Schutz-funktionen
Abschaltung der Ausgangsspannung . Neustart mit Wegnahme der Primärspannung
20 - 90%, nicht kondensierend
-20 - +60
105 -160% über NennlastStrombgrenzung, wird automatisch zurückgesetzt
-40 - +85 10 - 95% rel. Luftfeuchtigkeit
10 - 500Hz, 2G, 10min./1Zyklus, 60 Min. X,Y,Z-Achsen
AllgemeineDaten
Eingang/Ausgang: 3k
100MOhm / 500VDC
216,2k Stunden min. MIL-HDBK-217F (25°C)
Umgebung
Datenblatt
OTT GmbH & Co. KG ● D-78652 Deißlingen ● Tel.: +49 (0)7420-9399-0 ● Fax.: +49 (0)7420-9399-25 ● Email: [email protected]
Blockschaltbild
Leistungsherabsetzung
M e c h a n i s c h e E i g e n s c h a f t e n Maßeinheit: mm
date: 13-02-2007
-2 0 0 10 20 30 40 5 0 6 0 70
20
40
60
80
100
Umgebungstemeratur (°C)
Bel
astb
arke
it (
%)
Terminal PIN Nr. ZuordnungPin No. Pin No.
2
1 5,6
3,4
7
8
Assignment Assignment
+V
AC/N
AC/L
-V
LED
+VADJ.
Zulässige Befestigungsschiene: TS35/7.5 oder TS35/15
93
655
55
5
34
2
37
.75
1
78
12
.2
7
8
45
68
46.5
27
.4
3
47
56
46.5
35
Gehäuse Nr. 918B
Datenblatt
OTT GmbH & Co. KG ● 78652 Deißlingen ● Tel.: 07420-9399-0 ● Fax.: 07420-9399-25 ● Email: [email protected]
SPECIFICATION
Features :
file:
date: 08-02-2007xx-xxxx
Serial-No.
75W Single Output
Industrial DIN Rail Power Supply
Universal AC input/Full range
Protections:Short circuit/Over load/Over voltage/Over temperature
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
LED indicator for power on
100% full load burn-in test
Fix switching frequency at 50KHz
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
DIMENSION
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
12V 24V 48V
6.3A 3.2A 1.6A
0 ~ 6. 3A 0 ~ 3 .2A 0 ~ 1 .6A
76 W 7 6.8 W 7 6.8 W
10 0mVp -p 150 mVp- p 2 40m Vp-p
2.0% 1.0% 1.0%
12 ~ 1 4V 2 4 ~ 28V 48 ~ 53 V
0.5% 0.5% 0.5%
1.0% 1.0% 1.0%
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
76% 80% 81%
1.6A/115V 0.96A/230V
COLD START 20A/115VAC 40A/230VAC
<1mA / 240VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
15 ~ 16.5V 29 ~ 34V 58 ~ 65V
Protection type : Hiccup mode, recovers automatically after fault condition is removed
85 5 (TSW1) Detect on heat sink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, TUV EN60950-1 Approved
Compliance to EN55011,EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
-10 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
123.1K hrs min. MIL-HDBK-217F (25 )
55.5*125.2*100mm (W*H*D)
0.6Kg; 20pcs/13Kg/1.1CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
1000ms, 60ms/230VAC 1800ms, 60ms/115VAC at full load
60ms/230VAC 12ms/115VAC at full load
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
EMI CONDUCTION & RADIATION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
MTBF
OTHERS
ENVIRONMENT
PROTECTION
SAFETY &
EMC(Note 4)
R
AKL10004-01
AKL10004-02
AKL10004-00
75W Single Output
Industrial DIN Rail Power Supply
file:
date: 29.11.2006xx-xxxx
Serial-No.
-10 0 10 20 30 45 50 60
20
40
60
80
100
12V
24V,48V
85 90 105 125 145 165 185 205 225 265245
100
90
80
70
60
50
40
Terminal Pin. No Assignment (TB1) Terminal Pin. No Assignment (TB2)
Pin No. Pin No.
1 1,2
2 3,4
3
Assignment Assignment
FG
AC/L(DC-)
AC/N(DC+)
DC OUTPUT +V
DC OUTPUT -V
35
ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15
Mechanical Specification
Output Derating Output Derating Vs Input Voltage
Case No. 923 Unit:mm
AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz
LO
AD
(%
)
(VE
RT
ICA
L)
1
3
2
TB1 TB2
LED
2
4
3
1
+VADJ.125.2
55
.5
10
0
LO
AD
(%
)
Schaltnetzteil 1-phasig
- voller AC-Eingangsbereich (über Schalter wählbar)- langlebig- hohe Leistungsfähigkeit, geringe Betriebstemperatur- eingebauter Entstörfilter, geringe Restwelligkeit- LED - Anzeige- kompakte Größe, Leicht- 100% Burn-In Test unter Volllast- Kurzschluss- / Überlast- / Überspannungs- / Temperaturschutz- ohne Lüfter- Zulassungen: UL/TUV/CE- Sicherheit: UL508, UL60950-1, TUV EN 60950-1- EMV: EN55022 Klasse B, EN61000-3-2,3,
EN61000-6-2, EN61000-4-2,3,1,2,3,11, ENV50204
AKL10005-01
Ausgangsspannung [VDC] 24
Einstellbereich der Ausgangsspannung [VDC] 24 ~ 28
Nennstrom [A] 5
Nennleistung [W] 120
Restwelligkeit (max.) [mVss] 80
Spannungstoleranz [%] +/- 1
Netzausfallüberbrückung (typ.)
Eingangsspannungsbereich
Frequenzbereich [Hz] 47 - 63
Wirkungsgrad (typ.) [%] 80
Stromaufnahme (typ.)
Einschaltstossstrom (typ.)
Leckstrom
Überlast
Überspannung [VDC] 29 ~33
Übertemperatur [°C] 90 +/-5
Umgebungstemperatur (Betrieb) [°C]
Luftfeuchtigkeit (Betrieb)
Umgebungstemperatur (Lagerung) [°C]
Vibration
Isolationsspannung [VAC]
Isolationswiderstand
MTBF
Abmessungen (A, B, C) [mm] 100x66x126
Gewicht [kg] 0,79
Artikelnummer
36ms / 230VAC 32ms / 115VAC (bei Nennstorm)
88 ~ 132VAC / 176 ~264VAC (umschaltbar) 248 ~ 370VDC
Eingang2,6A / 115VAC 1,6A / 230VAC
Kaltstart 20A / 115VAC 40A / 230VAC
<3,5mA / 240VAC
Ausgang
Schutz-funktionen Abschaltung der Ausgangsspannung . Neustart mit Wegnahme der Primärspannung
Abschaltung der Ausgangsspannung, automatischer Neustart nach Temperaturrückgang
20 ~ 90%, nicht kondensierend
-10 ~+60
105 ~150% über NennlastStrombgrenzung, wird automatisch zurückgesetzt
-20 ~ +85, 10 ~95% rel. Luftfeuchtigkeit
10 ~ 500Hz, 2G, 10min./1Zyklus, 60 Min. X,Y,Z-Achsen
AllgemeineDaten
Eingan/Ausgang: 3k Eingang/Gehäuse 1,5k Ausgang Gehäuse 0,5k
100MOhm / 500VDC
136.800 Stunden min. MIL-HDBK-25°C
Umgebung
Datenblatt
OTT GmbH & Co. KG ● D-78652 Deißlingen ● Tel.: +49 (0)7420-9399-0 ● Fax.: +49 (0)7420-9399-25 ● Email: [email protected]
Case No. 921A Unit:mm
INPUT VOLTAGE (V) 60Hz
UT
UT
VT
GE
(V)
OP
O
LA
UT
UT
OP
L
RIP
PE
(m
Vp
-p)
Ta=25
Terminal Pin. No Assignment (TB1) Terminal Pin. No Assignment (TB2)Pin No. Pin No.
1 1,22 3,43
Assignment AssignmentFG
AC/LAC/N
DC OUTPUT +VDC OUTPUT -V
AMBIENT TEMPERATURE ( )
A%
)L
OD
(
-10 0 10 20 30 45 50 60
20
40
60
80
100
12V,24V
48V
100200
85170160
8
80180 190
9590
12
16
20
24
115230210 220
110105250240 260125120 130
28
32
80
100
150
200
250
300
350
(VERTICAL)
Mechanical Specification
Output Derating Static Characteristics (24V)
ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15
35
21
3
TB2TB1
4
21
3
LED
+VADJ.125.2
115
VAC
65
.5
23
0VA
C
10
0
Datenblatt
OTT GmbH & Co. KG ● D-78652 Deißlingen ● Tel.: +49 (0)7420-9399-0 ● Fax.: +49 (0)7420-9399-25 ● Email: [email protected]
SPECIFICATION
AKL10006-xx240W Single Output
Industrial DIN Rail Power Supply
file:
date: 15-02-2007xx-xxxx
Serial-No.
Features :
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE Note.5
FREQUENCY RANGE
EFFICIENCY (Typ.)INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
SAFETY &
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT (Typ.)
24V 48V
10A 5A
0 ~ 10A 0 ~ 5A
240W 240W
80mVp-p 150mVp-p
24 ~ 28V 48 ~ 53V
1.0%
0.5% 0.5%
1.0%
1.0%
1.0%
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
84% 85%
54 ~ 60V
2.8A/115VAC 1.4A/230VAC
COLD START 27A/115VAC 45A/230VAC<3.5mA / 240VAC105 ~ 150% rated output power
30 ~ 36V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover100 5 (TSW1)Detect on heat sink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
-10 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 5010 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
105.5Khrs min. MIL-HDBK-217F (25 )
125.5*125.2*100mm (W*H*D)1.2Kg; 12pcs/15.5Kg/1.2CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.5. Derating may be needed under low input voltages. Please check the derating curve for more details.
UL508, TUV EN60950-1 ApprovedUL60950-1,
Compliance to EN55011,EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
Universal AC input / Full range
Built in active PFC function
Protections:Short circuit/Over load/Over voltage/Over temperature
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
LED indicator for power on
100% full load burn-in test
Fixed switching frequency at 100KHz
ENVIRONMENT
PROTECTION
EMI CONDUCTION & RADIATIONEMC(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
800ms, 40ms 00ms, 40ms/230VAC 8 /115VAC at full load
24ms ms/230VAC 24 /115VAC at full load
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
POWER FACTOR (Typ.) 0.96/230VAC 0.99/115VAC at full load
R
AKL10006-02
240W Single Output
Industrial DIN Rail Power Supply
file:
date: 15.02.2007xx-xxxx
Serial-No.
Case No. 922A Unit:mm
INPUT VOLTAGE (V) 60Hz
AL
OD
(%
)
Ta=25
Terminal Pin. No Assignment (TB1) Terminal Pin. No Assignment (TB2)Pin No. Pin No.
1 1,22 3,43
Assignment AssignmentFG
AC/LAC/N
DC OUTPUT +VDC OUTPUT -V
AMBIENT TEMPERATURE ( )
LO
AD
(%
)
-10 0 10 20 30 40 50 55 60 70
Vin: 230VAC110VAC
20
--
40
60
80
100
100
40
85 110
50
60
70
80
155135 230 264
90
100
(VERTICAL)
Mechanical Specification
Output Derating Output derating VS input voltage
110VAC
230VAC
Admissible Din Rail: TS35/7.5 or TS35/15
35
+VADJ.
125.5
12
5.2
100
TB2
3
TB1 LED
2 1 1234
SPECIFICATION
Features :
480W Single Output
Industrial DIN Rail Power Supply
file:
date: 15-02-2007xx-xxxx
Serial-No.
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT (Typ.)
1200ms, 40ms/230VAC at full load
16ms/230VAC at full load
180 ~ 264VAC 250 ~ 370VDC
47 ~ 63Hz
89%
0.7
4A/230VAC
54 ~ 60V
COLD START 40A/230VAC
<3.5mA / 240VAC
105 ~ 150% rated output power
30 ~ 36V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover
100 5 (TSW : Detect on heatsink of power switch)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, TUV EN60950-1 ApprovedUL60950-1,
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
-20 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
180.9Khrs min. MIL-HDBK-217F (25 )
227*125.2*100mm (W*H*D)
2.4Kg; 6pcs/15Kg/1.75CUFT
POWER FACTOR (Typ.)
48V
10A
0 ~ 10A
480W
120mVp-p
48 ~ 53V
1.0%
0.5%
1.0%
24V
20A
0 ~ 20A
480W
120mVp-p
24 ~ 28V
1.0%
0.5%
1.0%
Built-in passive PFC function compliance to EN61000-3-2
High efficiency 89% and low dissipation
Protections:Short circuit/Over load/Over voltage/Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION
ENVIRONMENT
SAFETY &
EMC(Note 4)
PROTECTION
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
1. All parameters NOT specially mentioned are measured at 230VAC input, r ated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
R
AKL10007-02 AKL10007-01
480 W Single Output
Industrial DIN Rail with PFC Function
file:
date: 15.02.2007xx-xxxx
Serial-No.
File Name:DRP-480-SPEC 2005-09-06
Mechanical Specification
Derating Curve Output Derating VS Input Voltage
Case No.930 Unit:mm
AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz
180 190 200 264
100
90
80
70
60
50
40
LO
AD
(%
)
LO
AD
(%
)
-20 0 10 20 30 40 50 60 70 (VERTICAL)
20
40
60
80
100
TB1 Terminal Pin. No Assignment TB2 Terminal Pin. No Assignment
Pin No. Pin No.
1 1,2
3
2 3,4
Assignment Assignment
FG
AC/N(DC-)
AC/L(DC+) DC OUTPUT +V
DC OUTPUT -V
227100
+V ADJ.
35
3 12
TB1 TB2
12
5.2
34LED 2 1
ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15
DRP-480series480W Single Output Industrial DIN RAIL with PFC Function
Features :
file:
date: 15-02-2007xx-xxxx
Serial-No.
240W Three Phase
Industrial DIN RAIL Power Supply
Three-Phase AC 340 ~ 550V wide range input
High efficiency 89% and low dissipation
Protections:Short circuit/Over load/Over voltage/Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
R
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUTVOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)INPUT
INRUSH CURRENT (max.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT
24V
10A
0 ~ 10A
240W
80mVp-p
24 ~ 28V
1.0%
0.5%
0.5%
1200ms, 40ms, 20ms/400VAC 800ms, 40ms, 40ms/500VAC at full load
Three-Phase 340 ~ 550VAC 480 ~ 780VDC
47 ~ 63Hz
89%
0.95A/400VAC 0.75A/500VAC
COLD START 50A
<3.5mA / 530VAC
105 ~ 150% rated output power
30 ~ 36V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover
100 5 (TSW) Detect on heatsink of power switch
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, UL60950-1, TUV EN60950-1 Approved
Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
-20 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
114.6Khrs min. MIL-HDBK-217F (25 )
125.5*125.2*100mm (W*H*D)
1.3Kg; 12pcs/16.6Kg/1.34CUFT
48V
5A
0 ~ 5A
240W
80mVp-p
48 ~ 55V
1.0%
0.5%
0.5%
59 ~ 66V
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC(Note 4)
PROTECTION
EMI CONDUCTION & RADIATION
1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.5. Dual phase operation: derating of 20% is required.
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
Industrial DIN RAIL Power Supply
240W Three Phase
file:
date: 08.02.2007xx-xxxx
Serial-No.
Mechanical Specification
Derating Curve
Case No. 922A Unit:mm
AMBIENT TEMPERATURE ( )
LO
AD
(%
)
-20 0 10 20 30 40 50 60 70 (VERTICAL)
20
40
60
80
100
TB1 Terminal Pin. No Assignment TB2 Terminal Pin. No Assignment
Pin No. Pin No.
1 1,2
3
4
2 3,4
Assignment Assignment
AC/L2
AC/L1
AC/L3
DC OUTPUT +V
DC OUTPUT -V
Admissible Din Rail: TS35/7.5 or TS35/15
1234LED
TB1 TB2
23 1
125.5
12
5.5
100
+V ADJ.
4
Static Characteristics
LO
AD
(%
)
INPUT VOLTAGE (VAC) 60Hz
340 355 370 385 400 415 475430 490460 505 520 550
90
100
80
70
60
50
40
Three phase operation
Dual phase operation
35
FG
SPECIFICATION
Features :
file:
date: 08-02-2007xx-xxxx
Serial-No.
480W Three Phase
Industrial DIN RAIL Power Supply
R
Three-Phase AC 340 ~ 550V wide range input
High efficiency 89% and low dissipation
Protections:Short circuit/Over load/Over voltage/Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT (Typ.)
24V
20A
0 ~ 20A
480W
80mVp-p
24 ~ 28V
1.0%
0.5%
0.5%
1200ms, 40ms/400VAC 800ms, 40ms/500VAC at full load
16ms/400VAC 35ms/500VAC at full load
Three-Phase 340 ~ 550VAC 480 ~ 780VDC
47 ~ 63Hz
89%
1.7A/400VAC 1.3A/500VAC
COLD START 50A
<3.5mA / 530VAC
105 ~ 150% rated output power
30 ~ 36V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover
110 5 (TSW) Detect on heatsink of power switch
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, UL60950-1, TUV EN60950-1 Approved
Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
-20 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
91.1Khrs min. MIL-HDBK-217F (25 )
227*125.2*100mm (W*H*D)
2.5Kg; 6pcs/16Kg/1.75CUFT
48V
10A
0 ~ 10A
480W
80mVp-p
48 ~ 55V
1.0%
0.5%
0.5%
59 ~ 66V
ENVIRONMENT
SAFETY &
EMC(Note 4)
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & IRADIAT ON
NOTE1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.5. Dual phase operation: derating of 20% is required.
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
90%
AKL10009-01
Industrial DIN RAIL Power Supply
480W Three Phase
file:
date: 15.02.2007xx-xxxx
Serial-No.
Mechanical Specification
Derating Curve
Case No.930A Unit:mm
AMBIENT TEMPERATURE ( )
LO
AD
(%
)
-20 0 10 20 30 40 50 60 70 (VERTICAL)
20
40
60
80
100
Admissible Din Rail: TS35/7.5 or TS35/15
TB2 Terminal Pin. No Assignment
Pin No.
1,2
3,4
Assignment
DC OUTPUT +V
DC OUTPUT -V
TB1 Terminal Pin. No Assignment
Pin No.
1
3
4
2
Assignment
FG
AC/L2
AC/L3
AC/L1
227
12
5.2
+V ADJ.
35
TB1 TB234LED 2 1
100
24 3 1
Static Characteristics
LO
AD
(%
)
INPUT VOLTAGE (VAC) 60Hz
340 355 370 385 400 415 475430 490460 505 520 550
90
100
80
85
70
60
50
40
Three phase operation
Dual phase operation
Industrial DIN RAIL Power Supply
960W Three Phase
SPECIFICATION
Features :
file:
date: 16-02-2007xx-xxxx
Serial-No.
Three-Phase AC 340 ~ 550V wide range input
High efficiency 91% and low dissipation
Protections:Short circuit/Over load/Over voltage/Over temperature
Optional parallel function(1+1)
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in testR
Protection type : Constant current limiting, unit will shut down o/p voltage after 3 sec. , re-power on to recover
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)INPUT
INRUSH CURRENT (max.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT (Typ.)
24V
40A
0 ~ 40A
960W
80mVp-p
24 ~ 28V
1.0%
0.5%
0.5%
200ms, 60ms/400VAC 200ms, 60ms/500VAC at full load
14ms/400VAC 30ms/500VAC at full load
Three-Phase 340 ~ 550VAC
47 ~ 63Hz
91%
2A/400VAC 1.6A/500VAC
COLD START 50A
<3.5mA / 530VAC
105 ~ 125% rated output power
30 ~ 36V
Protection type : Shut down o/p voltage, re-power on to recover
110 5 (TSW1) Detect on heatsink of power transistor 85 5 (TSW2) Detect on heatsink of power diode
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, UL60950-1, TUV EN60950-1 Approved
Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A
-20 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
Component: Compliance to IEC60068-2-610 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting:
122.5Khrs min. MIL-HDBK-217F (25 )
276*125.2*100mm (W*H*D)
3.3Kg; 4pcs/14.2Kg/1.14CUFT
48V
20A
0 ~ 20A
960W
80mVp-p
48 ~ 55V
1.0%
0.5%
0.5%
59 ~ 66V
ENVIRONMENT
SAFETY &
EMC(Note 4)
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION
NOTE1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
92%
Serial-No.
Industrial DIN RAIL Power Supply
960W Three Phase
Mechanical Specification
Derating Curve
Case No.934 Unit:mm
AMBIENT TEMPERATURE ( )
LO
AD
(%
)
-20 0 10 20 30 40 45 50 60 70
20
40
60
50
80
100
Admissible Din Rail: TS35/7.5 or TS35/15
TB2 Terminal Pin. No Assignment
Pin No.
1,2,3
4,5,6
Assignment
DC OUTPUT +V
DC OUTPUT -V
TB1 Terminal Pin. No Assignment
Pin No.
1
3
4
2
Assignment
FG
AC/L2
AC/L3
AC/L1
Static Characteristics
LO
AD
(%
)
INPUT VOLTAGE (VAC) 60Hz
340 355 380 385 400 415 475430 490460 505 520 550
90
100
80
70
60
50
40
35
(VERTICAL)
36 2 124 3 1 45
276100
TB1 TB2
12
5.2
LED
+VADJ
ALARM
file:
date: 16-02-2007xx-xxxx
Industrial DIN RAIL Power Supply
960W Three Phase
file:
date: 16-02-2007xx-xxxx
Serial-No.
TB2 Terminal Pin. No Assignment
Pin No.
1,2,3
4,5,6
7
8
Assignment
DC OUTPUT +V
DC OUTPUT -V
GND
P(Current Share)
TB1 Terminal Pin. No Assignment
Note: Under parallel operation, if the load current is too small, only one PSU(master) would provide the power and hence the LEDindicator of other PSUs may not light up.
Pin No.
1
3
4
2
Assignment
FG
AC/L2
AC/L3
AC/L1
5 413
TB1 TB1
PSU PSU
4 2 126 38 7 78 36 2 124 3 1 45
LOAD
+V -V
TB2
LED LED
TB2
Parallel Function (1+1)-Optional (Special order required)
40 W Single Output
Industrial DIN Rail Power Supply
file:date: 19-03-08
xx-xxxx
Serial-No.
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
NEC class 2 / LPS compliant (12V,24V,48V only)
LED indicator for power on
DC OK relay contact
No load power consumption<0.75W
100% full load burn-in test
Features :
SPECIFICATIONMODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME Note.5
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)INPUT
INRUSH CURRENT (Typ.)
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING HUMIDITY
WORKING TEMP.
DC OK SIGNAL
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
5V 12V 24V 48V
6A 3.33A 1.7A 0.83A
0 ~ 6A 0 ~ 3.33A 0 ~ 1.7A 0 ~ 0.83A
30W 40W 40.8W 39.8W
80mVp-p 120mVp -p 150mVp -p
24 ~ 30V
200mVp-p
48 ~ 56V
2.0% 1.0% 1.0% 1.0%
12 ~ 15V5 ~ 6V
1.0% 1.0% 1.0% 1.0%
1.0% 1.0% 1.0% 1.0%
500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
50ms/230VAC 20ms/115VAC at full load
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
78% 86% 88% 88%
1.1A/115VAC 0.7A/230VACCOLD START 30A/115VAC 60A/230VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed6.25 ~ 7.25V
Protection type : Shut down o/p voltage, re-power on to recover
15.6 ~ 18V 31.2 ~ 36V 57.6 ~ 64.8V
-20 ~ +70 (Refer to output load derating curve)
Relay contact rating(max.): 30V/1A resistive
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50Component : each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-610 ~ 500Hz, 2G 10min./1cycle, period for 60min.
301.7K hrs min. MIL-HDBK-217F (25 )
1. All parameters NOT specially mentioned are measured at 230VAC input, r ated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor.3. Tolerance : includes set up tolerance, line regulation and load regula tion.4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
UL508, TUV EN60950-1 approved, NEC class 2 / LPS compliant (12V,24V,48V only)
Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, ENV50204, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
PROTECTION
SAFETY &
FUNCTION
EMC(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION
40*90*100mm (W*H*D)
0.3Kg; 42pcs/13.6Kg/0.82CUFT
LEAKAGE CURRENT <1mA / 240VAC
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:>100M Ohms/500VDC 25 70%RH
file:
date: 19-03-08xx-xxxx
Block Diagram
Output Derating Static Characteristics (24V)
Mechanical Specification
Serial-No.
-20 0 10 20 30 45 55 60 70 (VERTICAL)
20
40
60
80
100
AMBIENT TEMPERATURE ( )
LO
AD
(%
)
INPUT VOLTAGE (VAC) 60Hz
85 10095 120115 160140 200180 240220 264
90
100
80
70
60
50
40
+
Install DIN rail TS35/7.5 or TS35/15
35
+V +V40
90
-V -V
N L
DC OK
+VADJ
5 5 5 5 5
7.57.5
100
DC OK Relay Contact
Contact Close When the output volta ge reaches the adjusted output voltage.
When the output voltage drop below 90% output voltage.
30V/1A resistive load
Contact Open
Contact Ratings (max.)
DC OK
Unit:mm
CIRCUITDETECTION
O.L.P.
EMIFILTER
&FILTER
POWERSWITCHING
FILTER&
RECTIFIERS +V
DC OK
-VI/P
CONTROL
O.V.P.
O.C.P.
fosc : 60KHz
RECTIFIRE
LOA
D (
%)
40 W Single Output
Industrial DIN Rail Power Supply
Ott GmbH & Co. KG Baarstrasse 3 D-78652 Deisslingen Tel. ++49 7420/9399-0 www.ott-antriebe.de
Seite 83
Ott GmbH & Co. KG Baarstrasse 3 D-78652 Deisslingen Tel. ++49 7420/9399-0 www.ott-antriebe.de
Seite 83
BLDC-/AC-Motoren
Kundenspezifische AC-Motoren
und BLDC-Motoren
Auch mit integrierter Reglung
Leistungen von 1 bis 1880 Watt
Spezielle Produkte mit besonders
hoher Lebensdauer
DKM-Motoren
Synchron- und Asynchronmotoren
mit Schnecken- oder Stirnradge-triebe Leistungen von 15 bis 200 Watt Spannungen von 110 bis 480 VAC
Bürstenbehaftete DC-Motoren
Leistungen von 6 bis 120 Watt Spannungen von 12 bis 90 VDC
Optional mit Bremse, Encoder
oder Tacho
DC-Motoren
Mit Schnecken- oder Stirnradge-
triebe und als Spindelantrieb liefer-bar
Auch getriebelos erhältlich
Leistungen von 0,5 bis 450 Watt
Über 50.000 Motoren vorrätig an
Lager
Hervorragendes Preis-Leistungs
Verhältnis
BLDC-Motoren
BLDC-Motoren mit Schnecken-
oder Planetengetriebe, in unter-schiedlichen Untersetzungen
Auch getriebelos erhältlich
Leistungen von 3 bis 1880 Watt
Nennspanung von 6 bis 72 VDC
Drehzahlen zwischen 0,03 und
40.000 U/min
TX-Motoren
Bürstenbehaftete DC-Motoren mit
Schnecken-, Stirnrad- oder Planeten-getriebe in unterschiedlichen Unter-setzungen
Nennspannungen von 12 bis 24 VDC
Optional mit Bremse, Encoder oder
Tacho
Modifizierte Motoren
Sonderanpassungen auch bei kleinen
Stückzahlen möglich
Auf Wunsch Anbau von Bremse,
Encoder, Tacho, oder Kabelkonfektionen
Aufbau von kompletten Positionierein-
heiten
Steuerungen-Servoregler
Für bürstenlose und bürstenbehaftete
DC-Motoren
Auch programmierbar und mit ver-
schiedenen BUS-Systemen
Elektronische Lastrelais
Übergabemodule und Verdrahtungs-
interface
Zubehör
Mechanische Zusatzkomponenten,
Steckachsen, Kettenräder, Gehäuse-teile
Kundenspezifische Zeichnungsteile
Elektronische Komponenten, Potis,
Anschlusskabel, Stecker, Entstörglie-der
Ott GmbH & Co. KG
Baarstraße 3
78652 Deißlingen
Tel. 07420 / 9399-0
Email [email protected]
Web www.ott-antriebe.de
Wir kombinieren Elektronik und Mechanik für Sie.
Und das seit 60 Jahren.
Die Ott GmbH & Co. KG bietet als Produktions-, Handels- und Dienstleistungsunternehmen Kom-ponenten und Systeme aus dem Bereich der Antriebstechnik und Elektronik an.
Als Vertretung der Firma Nidec, ehemals SWF, führen wir ein Lager in dem ständig circa 50.000 Motoren und über 1.000 Steuerungen vorrätig gehalten werden. Dies ermöglicht es, schnell auf Ihre Anforderungen zu reagieren. Darüber hinaus bieten wir auch die entsprechenden Steuerun-gen, Kupplungen, Kugelgewindespindeln und Spannungsversorgungen für Motoren an. In unse-rer Fertigung werden kundenspezifische Änderungen an Motoren, wie Wellenbearbeitungen, Auf-bau von Inkrementalgebern, Bremsen, Sondergetriebe und Steckverbindungen realisiert. Diese Sonderfertigungen werden auch bei kleinsten Stückzahlen durchgeführt. Damit können komplette
Systemlösungen nach Ihren Aufgabenstellungen projektiert und gefertigt werden.
Durch die jüngste Produkterweiterung sind Antriebe von ca. 1 Watt bis über 3 Kilowatt lieferbar.
Als weitere Serviceleistung führen wir Reparaturen an Motoren und Regelteilen der Firma Nidec-Valeo bzw. SWF durch.