Upload
duonghanh
View
223
Download
3
Embed Size (px)
Citation preview
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI 420/302 TECHNICAL DATA SHEET
Forklift with AL-302 Spray Arm
DESCRIPTION
Multicrete Systems Inc. announces the Multicrete MSU 420/302, a complete mobile shotcrete unit complete with front forks and a shotcrete boom with a reach of over 18 feet!
CARRIER
Make & Model Kubota, R420 D1503-T-RP-1Type Liquid cooled, 3 cylinderTurbo DieselHorse PowerOperating WeightDisplacementTurbo ChargerE-TVCSOverall WidthWheel BaseGround ClearanceTreadAngle of ArticulationFrame OscillationFORKLIFTMaximum Lift Forks (folding) CapacityFree Lift
43.0 @ 2,600 rpm7,275 lbs (3,300 kg)91.4 cu. In. (1,497 cc)YesYes – Low Emissions4’-11.8”5’-9.9”11.3”3’-10.5”40
810’2-1/2” X 5”X40”5500 lbsFull
SHOTCRETE BOOM
Maximum HeightMaximum LengthMinimum LengthAngle of RotationSpraying AngleRemote ControlHydraulic AggregateElectric DriveOr Air DriveDiesel Engine
21’19’8’110240Hydraulic14 L/min5.5 kW7 kWVia carrier
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI 420/APT TECHNICAL DATA SHEET
Featuring Multicrete Auto Parallel Travel System
Figure 1: Fully extended Multicrete Auto Parallel Travel Syste demonstrating vertical reach.
Figure 2: Fully extended Multicrete Auto Parallel Travel System demonstrating horizontal reach
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI 520/302 TECHNICAL DATA SHEET
Forklift with AL-302 Spray Arm
DESCRIPTION
Multicrete Systems Inc. announces the Multicrete MSU 520/302, a complete mobile shotcrete unit complete with front forks and a shotcrete boom with a reach of over 18 feet!
CARRIER
Make & Model Kubota, R520S V2203-M-E3TypeTransmissionHorse PowerOperating WeightDisplacementTurbo ChargerE-TVCSOverall WidthWheel BaseGround ClearanceTreadAngle of ArticulationFrame OscillationBrakes/Service /Parking
FORKLIFTMaximum Lift Forks (folding) CapacityFree Lift
Liquid cooled, 4 cylinder diesel1-F, 1-R load sensing46.0 @ 2,600 rpm8,980 lbs (4,082 kg)134.1 cu. In. (2,095 cc)NoYes – Low Emissions69.3” (173.25 cm)76.8” (192 cm)12.8” (32 cm)53.5” (133.75 cm)408Encl. self adjust wet discSpring apply, hydr. wet disc
10’2-1/2” X 5”X40”5500 lbsFull
SHOTCRETE BOOM
Maximum HeightMaximum LengthMinimum LengthAngle of RotationSpraying AngleRemote ControlHydraulic AggregateElectric DriveOr Air DriveDiesel Engine
21’19’8’110240Hydraulic14 L/min5.5 kW7 kWVia carrier
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI HURON 4 SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® Shotcrete Machine, AL-302 Spray Arm on Carrier
DESCRIPTION
A shotcrete carrier which includes a state of the art Aliva 257 wet/dry shotcrete machine on the rear, an Aliva® 302 wet mix shotcrete spraying arm on the front, enhanced hydraulics, self contained liquid accelerator storage & pumping system all on a Huron 4 transmixer chassis. A very compact, manueverable, tough unit designed to get the job done!
SPECIFICATIONS, HURON 4
TRANSMIXER TRUCK:
Chassis
Monoblock. Heavy duty type.
Engine
Diesel CUMMINGS type QSB 4.5 (TIER lll-COM lll),4 cylinders, turbo intercooler.
Liquid cooling. Power DIN 116kW
(155HP) to 2,200 r.p.m. It is designed to work at 4700 MASL.
Axles
Monolithic with epicycloids reducer.
Dynamic loading capacity per axle 8000 kg.
Steering type front axle with oscillating assembly. Fixed rear axle.
Transmission
Hydrostatic type with automatic regulation.
Axial pistons pump of variable flow applied directly to diesel engine. Hydraulic motor at axial pistons mounted on reducer cap.
Figure 1: Aliva® 302 Spray Boom partially extended.
Figure 2: Mixing drum and liquid accelerator storage.
Figure 3: Aliva® 302 Spray Boom with 240/360 degree Nozzle rotation.
SPECIFICATIONS, CONTINUED
Steering
Hydraulic on front axle.
Brakes
Internal discs oil bathed on front wheels.
Hydraulic activate in two independent circuits.
Parking brakes on transmission with hand lever control.
Drum
Concrete output capacity:Direct unloading height:Unloading height:Hydraulic rotation of drum for loading-mixing and unloading is effect by electric speed regulation of rpm.
Water System
Hydraulic operated self-priming water pump.
The water is supplied from an external source, taken directly to the drum, to the tank or the washing hose. It can also be taken from the truck mixer tank to the drum or the washing hose. High pressure pump for cleaning purposes. Litre counter.
Max Slope
Fully loaded: 30% (SAE normative)
Speed
1st:2nd:
Steering Radius
Internal:External:
Electrical
12 V battery 180 Ah, 650 A
Tires
10’00R20 16PR
0-8 km/hr (for working)0-20 km/hr (for movement)
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI HURON 4 SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® Shotcrete Machine, AL-302 Spray Arm on Carrier
Figure 4: Drum discharge chute to Aliva® 257 hopper.
Figure 5: Aliva® 302 boom retracted for driving.
Figure 6: Aliva® 302 mounted in front of engine compartment.
4 m3
1465 mm1100 mm
4,150 mm7,800 mm
SPECIFICATIONS, ALIVA® 257 SHOTCRETE MACHINE:
The AL-257 is the universal machine for the application of dry- and wet shotcrete in the thin-stream method. The new and very compact design of the machine impresses through its dimensions, weight and performance. With just 750 kg and dimensions as little as a small dry shotcrete machine, the AL-257 fits on the back of the Huron 4 and is easy to operate. With its unbelievable output capacity range from 0.7– 9.6 m3/h (with 3 rotor sizes) the machine works on small concrete renovation work as efficient as on big slope protection or in mines. Less maintenance and wear cost makes it the ideal shotcrete machine for all applications.
Built in components
The AL-257 is equipped with a fully automatic lubrication system for the rotor-discs. The rotor-speed is adjusted with a frequency converter and therefore, can be adjusted to every specific need on the job.
Sealing system
The machine is equipped with rotors made of high tech aluminum and is operating with steel-on-steel wear and rotor plates. Experience has shown up to 10 times less wear on the steel plates, depending on material, output capacity, hose diameter and compressed air supply! This again leads to less down time and wear cost and therefore to a more economical spraying operation.
SPECIFICATIONS, ALIVA® 302 SPRAY BOOM:
The telescope spraying arm Aliva® 302 is used for the application of sprayed concrete in mines, small galleries and excavations. With its simple and rigid construction, the Aliva® 302 is very suitable for the mounting onto different types of carriers.
Transport Length:
Transport Width:
Transport Height:
Weight of Arm approx.:
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MSI HURON 4 SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® Shotcrete Machine, AL-302 Spray Arm on Carrier
2.45 m
0.5 m
2.0 m
550 kg
Reach, rotation and precision all contribute to remotely operated quality application of shotcrete material to all of those tough to get into places. Safe workers, minimal hazard, correct technique, less waste, more profitability. The Huron 4 application Shotcrete carrier is your answer.
SUPPORT YOU CAN COUNT ON!
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
HYBRID WET® SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® 257 Shotcrete Machine, AL-302 Spary Arm on a Getman 64 Carrier
DESCRIPTION
This Shotcrete Carrier is based on simplicity. Load & haul dry, pre-mixed material to the shooting site. Water is added to the Mixing Auger, just before the Aliva 257 Shotcrete Pump and it is sprayed “wet” at a low slump for reduced accelerator needs and high strength and adhesion. This unit can also spray “predampened” dry shotcrete!
SPECIFICATIONS
GETMAN 64 CARRIER CHASSIS
Chassis:
Heavy duty type articulating frame steering four wheel drive
Engine:
Mercedes Benz OM904LA Diesel 129kW (173hp) @2,200 rpm, fuel/water separator, Donaldson dry, dual element air cleaner, catalytic purifier with muffler, 24V, 100A alternator, 114 litre fuel capacity.
Axle & Tires:
John Deere YZ17337 Inboard planetary axles with wet disc brakes 10.00x20-16PR mine service tires.
Transmission:
Clark/Dana 32000 3 speed full reversing powershift
Steering:
Orbital controlled articulating steering, heavy duty self-aligning bearings inside replaceable inserts, two double-acting steering cylinders.
Brakes:
Service, fully hydraulic wet disc brakes each axle. Secondary, spring-applied, hydraulic released wet disc secondary and park brake. Automatic secondary brake application upon loss of power or pressure.
Figure 1: Aliva 302 Spray Boom (front) and Aliva 257 Wet/Dry shotcrete machine (rear) integrally assembled on Getman 64 Carrier
Figure 2: Aliva 302 Spray Arm Extended
Figure 3: Liquid Accelerator storage & pump
Hydraulic System:
Open center hydraulic circuits, gear-type hydraulic pump, 151 litre hydraulic resevoir, with sight gauges. 100 mesh suction strainers, return line, spin-on filters, 10 micron rating, diagnostic test ports with quick couple parker fittings each axle service break pressure, hydraulic pumps.
www.multicretesystems.com
HYBRID WET® SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® 257 Shotcrete Machine, AL-302 Spary Arm on a Getman 64 Carrier
Also equipped with...
Audio backup alarm, 5 lb. fire extinguisher, four nozzle fire suppression system Ansul LTA-101-30, wheel chocks, Lincoln automatic lubrication.
Speed on Grade:
21 kph.....................................5% 12 kph....................................15% 8 hph......................................20%
Steering Radius:
Internal.........................3,988 mm External.........................6,731 mm
Wheel base:
Length (axle to axle......3,658 mm Width.............................2,083 mm
ELECTRICAL & INSTRUMENTS
Maintenance free 12V battery, full instrumentation, engine/transmission, voltometer, hour meter, battery master disconnect switch, lockable, 50W halogen headlights, two front/two rear, two red taillights, brake accumulator pressure gauges, low pressure warning light, “park brake applied” warning light, wiring fully sealed connectors, sealed and oil resistant covering, instrument associated switches mounted in electrical box.
Figure 4: Aliva 302 Spray Boom with 240/360 degree nozzle rotation
Figure 5: Shotcrete Mixing Auger
Figure 6: Rear-view lights and backup camera
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
HYBRID WET® SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® 257 Shotcrete Machine, AL-302 Spary Arm on a Getman 64 Carrier
SPECIFICATIONS
ALIVA 257 SHOTCRETE MACHINE
The AL-257 is the universal machine for the application of dry- and wet shotcrete in the thin-stream method. The new and very compact design of the machine impresses through its dimensions, weight and performance. With just 750 kg and dimensions as little as a small dry shotcrete machine, the AL-257 fits on the back of the Huron 4 and is easy to operate. With its unbelievable output capacity range from 0.7– 9.6 m3/h (with 3 rotor sizes) the machine works on small concrete renovation work as efficient as on big slope protection or in mines. Less maintenance and wear cost makes it the ideal shotcrete machine for all applications.
Built in components:
The AL-257 is equipped with a fully automatic lubrication system for the rotor-discs. The rotor-speed is adjusted with a frequency converter and therefore, can be adjusted to every specific need on the job.
Sealing system: The machine is equipped with rotors made of high tech aluminum and is operating with steel - on -steel wear and rotor plates. Experience has shown up to 10 times less wear on the steel plates, depending on material, output capacity, hose diameter and compressed air supply! This again leads to less down time and wear cost and therefore to a more economical spraying operation.
Figure 7: Mixing auger discharge to Aliva 257 hopper
Figure 8: Aliva 257 Shotcrete Machine
Figure 9: Mixing auger & Aliva 257 hopper
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
HYBRID WET® SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® 257 Shotcrete Machine, AL-302 Spary Arm on a Getman 64 Carrier
SPECIFICATIONS
ALIVA 302 SPRAY BOOM
The telescope spraying arm Aliva 302 is used for the application of sprayed concrete in mines, small galleries and excavations.
With its simple and rigid construction, the Aliva 302 is very suitable for the mounting onto different types of carriers.
Transport Length……….2.45 m Transport Width…………..0.5 m Transport Height………....2.0 m Weight of Arm approx...550 kg
Reach, rotation and precision all contribute to remotely operated quality application of shotcrete material to all of those tough to get into places. Safe workers, minimal hazard, correct technique, less waste, more profitability. The Multicrete Hybrid Wet® Application Shotcrete Carrier is your answer.
Figure 10: 7 cu.yd. Storage hopper for dry pre-mixed product
Figure 11: Aliva 302 boom and work lights
Figure 12: Inside cab of Getman 64 Carrier
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
HYBRID WET® SHOTCRETE APPLICATION CARRIER TECHNICAL DATA SHEET
Aliva® 257 Shotcrete Machine, AL-302 Spary Arm on a Getman 64 Carrier
Figure 13: Dimensions of Multicrete Hybrid Wet® Shotcrete Carrier
Figure 14: Multicrete Hybrid Wet® Shotcrete Carrier - Ready to Ship
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MULTICRETE INTEGRAL SHOTCRETE UNIT TECHNICAL DATA SHEET
Pre-dampener and Aliva Dry Mix Shotcrete Machine Combination
DESCRIPTION
This easily transported Multicrete Integral Shotcrete Unit consists of an Aliva dry mix shotcrete machine and a Multicrete Predampener, mounted together on a common frame. Preparation includes connecting the “Bull Hose” from the air supply to the inlet on the predampener frame. The water line is then connected to the spray nozzle assembly located on the mix auger. Finally, the material delivery hose can be attached to the outlet chamber assembly of the Aliva pot and shotcreting can proceed.
PURPOSE
The Hopper on the Predampener allows for a continuous feed of pre-blended dry mix shotcrete - even during bulk bag changes. The feed auger located under the hopper then feeds a mix auger where water is added to suppress dust and to allow the nozzleman to easily regulate the water at the nozzle.
Power Options - Electric
5 hp helical snuggler gear motor to mix auger.3 hp variable speed motor to cross feed auger.Centrally mounted electrical control panels.
Power Options - Pneumatic
2” filter/regulator/lubricator system.12 hp vane motor, helical worm gear reducer to mix auger.7 hp vane motor, helical shaft mount reducer to feed auger.
Scoop Bucket Slots
“Tie-back” cable supports to Scoop Bucket
Raise Jack for clean-up (when opening mix auger belt)
Winnipeg, MBPh: 204-262-5900
Red Lake, ONPh: 807-735-3011
Thompson, MBPh: 204-677-5977
Snow Lake, MBPh: 204-358-7992
Flin Flon, MBPh: 204-687-6533
Saskatoon, SKPh: 306-651-2727
Edmonton, ABPh: 780-960-6692
www.multicretesystems.com
MOBILE SHOTCRETE SYSTEM TECHNICAL DATA SHEET
Aliva® Shotcrete Machine, AL-302 Spray Arm on Carrier
DESCRIPTION
A shotcrete carrier includes a dry mix hopper, a wet mix shotcrete spraying machine, and a mixing auger for wetting the dry mix as it is conveyed from the dry mix hopper to the shotcrete spraying machine on a common mobile frame.
The shotcrete spraying machine comprises an inlet hopper receiving the wet mix shotcrete from the mixing auger, and a rotor with chambers rotatable from a loading position in communication with the inlet hopper and a discharging position in communication with a pneumatic conveying line. The pneumatic conveying line conveys the wet mix shotcrete to a nozzle commonly supported on the mobile frame.
Figure 1: Aliva 302 Spray Boom fully extended for remote spraying of “backs” and large underground caverns.
Figure 2: Hopper for dry mix material discharges into Pre-dampener auger. “Earth damp” material is conveyed to ALIVA shotcrete machine where it is conveyed pneumatically for remote application.
SUPPORT
YOU CAN
COUNT ON!