Embed Size (px)
Citation preview
Adjustable height11mm, not adjustable.
Addition of BC-PH5 slope corrector gives 0-5% slope correction.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-0-NA pedestalDiameter 200mm, surface area 315cm2.
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5%Slope corrector BC-PH5 is placed under the base of pedestal
BC-0-NA. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-0-NA.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surface
of the head.
Position Height(mm) Breaking Breaking
Load(daN) Load(lbf) 1/1 11 2160 4817
1/2 11 1580 3523
1/4 11 815 1817
Safety value for maximum allowable load by compression for BC-0-NA:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.
��6DIHW\�IRU�WHFKQLFDO�IORRUV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH�WDEO��E\���ZLWK�D�VDIHW\�
factor of - 15 %
Note : The BUZON BC-0-NA pedestals in polypropylene are not designed to
support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
Technical data sheet
BC-0-NA
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25
mm
���6KLP� Enhances acoustic performance
and can help to level uneven paving materials.
- height 11mm
11mm
23mm
205mm
200mm
BC-0-NA 315cm2
315cm2
BC-0-NA+BC-PH5
3mm
17
mm
4.5mm
Adjustable height14mm, not adjustable.
Addition of BC-PH5 slope corrector gives 0-5% slope correction.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-1-NA pedestalDiameter 200mm, surface area 315cm2.
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5%Slope corrector BC-PH5 is placed under the base of pedestal
BC-1-NA. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-1-NA.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surface
of the head.
Position Height(mm) Breaking Breaking
Load(daN) Load(lbf) 1/1 14 9800 21854
1/2 14 7077 15781
1/4 14 3163 7054
Safety value for maximum allowable load by compression for BC-1-NA:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.
��6DIHW\�IRU�WHFKQLFDO�IORRUV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH�WDEO��E\���ZLWK�D�VDIHW\�
factor of - 15 %
Note : The BUZON BC-1-NA pedestals in polypropylene are not designed to
support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
Technical data sheet
BC-1-NA
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25
mm
25
mm
���6KLP� Enhances acoustic performance
and can help to level uneven paving materials.
- height 14mm
14mm
26mm
205mm
200mm
BC-1-NA 315cm2
315cm2
BC-1-NA+BC-PH5
3mm
17
mm
17
mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 28 to 40mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
40 to 52mm.
CompositionThe BC-02-SC is composed by 2 pieces (head + base).
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-02-SC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector BC-PH5 is placed under the base of pedestal
BC-02-SC. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-02-SC.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 40 1022 2278 1/2 40 657 1464 1/4 40 416 928
Safety value for maximum allowable load by compression for BC-02-SC:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-02-SC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CO RRECTOR
BC-PH5
Technical data sheet
BC-02-SC
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
145mm
145mm
28-40mm
40-52mm
200mm
205mm
BC-02-SC
BC-02-SC + BC-PH5
- adjustable from 28 to 40mm
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 40 to 55mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
52 to 67mm.
CompositionThe BC-2-SC is composed by 2 pieces (head + base).
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-2-SC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5%Slope corrector BC-PH5 is placed under the base of pedestal
BC-2-SC. Consisting of 2 cylindrical parts, it allows to compensate
for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-2-SC.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 55 1638 3653 1/2 55 1077 2401 1/4 55 753 1680
Safety value for maximum allowable load by compression for BC-2-SC:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�
safety factor of - 15 %Note : The BUZON BC-2-SC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
Technical data sheet
BC-2-SC
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
145mm
145mm
40-55mm
53-67mm
200mm
205mm
BC-2-SC
BC-2-SC + BC-PH5
- adjustable from 40 to 55mm
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 55 to 85mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
67 to 97mm.
CompositionThe BC-3-SC is composed by 2 pieces (head + base).
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-3-SC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5%Slope corrector BC-PH5 is placed under the base of pedestal
BC-3-SC. Consisting of 2 cylindrical parts, it allows to compensate
for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-3-SC.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 85 1280 2854 1/2 85 888 1981 1/4 85 588 1312
Safety value for maximum allowable load by compression for BC-3-SC:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�
safety factor of - 15 %Note : The BUZON BC-3-SC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
145mm
BC-3-SC
55-85mm
200mm
145mm
205mm
67-97mm
BC-3-SC + BC-PH5
Technical data sheet
BC-3-SC
- adjustable from 55 to 85mm
BC-PH5 SLOPE CORRECTOR
BC-3 BASE
BC-3 TOP
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 85 to 140mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
97 to 152mm.
CompositionThe BC-4-SC is composed by 2 pieces (head + base).
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-4-SC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector BC-PH5 is placed under the base of pedestal
BC-4-SC. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-4-SC.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 140 1482 3304 1/2 140 1122 2501 1/4 140 733 1635
Safety value for maximum allowable load by compression for BC-4-SC:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�
safety factor of - 15 %Note : The BUZON BC-4-SC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
145mm
BC-4-SC
85-140mm
200mm
145mm
205mm
97-152mm
BC-4-SC + BC-PH5
Technical data sheet
BC-4-SC
- adjustable from 85 to 140mm
BC-PH5 SLOPE CORRECTOR
BC-4 BASE
BC-4 TOP
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
+
+
0%
0 to 5%
SLOPE CORR ECTOR
BC-PH5
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 116 to 200mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
128 to 212mm.
CompositionThe BC-5-SC is composed by 2 pieces (head + base).
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-5-SC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector BC-PH5 is placed under the base of pedestal
BC-5-SC. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-5-SC.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 200 1290 2877 1/2 200 950 2119 1/4 200 595 1327
Safety value for maximum allowable load by compression for BC-5-SC:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�
safety factor of - 15 %Note : The BUZON BC-5-SC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
145mm
BC-5-SC
116-200mm
200mm
145mm
205mm
128-212mm
BC-5-SC + BC-PH5
Technical data sheet
BC-5-SC
- adjustable from 116 to 200mm
BC-PH5 SLOPE CORRECTOR
BC-5 BASE
BC-5 TOP
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
A
B
C
A
B
C
0%
0 to 5%
SLOPE CORR ECTOR
BC-PH5
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 198 to 230mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
210 to 242mm
CompositionBC-4 pedestal + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-6-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-6-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-6-INV.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 230 1188 2649 1/2 230 1070 2386 1/4 230 643 1434
Safety value for maximum allowable load by compression for BC-6-INV:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-6-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CO RRECTOR
BC-PH5
145mm
BC-6-INV
198-230mm
200mm
145mm
205mm
210-242mm
BC-6-INV + BC-PH5
Technical data sheet
BC-6-INV
- adjustable from 198 to 230mm
BC-PH5- SLOPE CORRECTOR
BC-4-BASE
BC-4 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
.
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 224 to 365mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
236 to 377mm.
CompositionBC-5-NSC pedestal + 1x Sleeve C3-BC5 .
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-7-NSC pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector BC-PH5 is placed under the base of pedestal
BC-7-NSC. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-7-NSC.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 365 1430 3189 1/2 365 1147 2557 1/4 365 768 1713
Safety value for maximum allowable load by compression for BC-7-NSC:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKH
table by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�
safety factor of - 15 %Note : The BUZON BC-7-NSC pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. =�,��GHV�+DXWV�6DUWV��=RQH�����3URORQJHPHQW�GH�OD�UXH�GH�O$EED\H���������%������+HUVWDO���%HOJLXP
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
145mmBC-7-NSC
224-365mm
200mm
145mm
205mm
236-377mm
BC-7-NSC + BC-PH5
Technical data sheet
BC-7-NSC
- adjustable from 224 to 365mm
BC-PH5 SLOPE CORRECTOR
BC-5 BASE
BC-5 TOP
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
C3-BC5SLEEVE
_
A
B
C
+
_
A
B
C
+
0%
0 to 5%
SLOPE CORR ECTOR
BC-PH5
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 342 to 455mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
354 to 467mm
CompositionBC-5 pedestal + 1x Sleeve C3-BC5 + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-8-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 1x)Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-8-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-8-INV.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 455 1230 2743 1/2 455 1043 2327 1/4 455 797 1777
Safety value for maximum allowable load by compression for BC-8-INV:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-8-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
145mm
BC-8-INV 145mm
205mm
354-467mm
BC-8-INV + BC-PH5
Technical data sheet
BC-8-INV
- adjustable from 342 to 455mm
BC-PH5 SLOPE CORRECTOR
BC-5-BASE
BC-5 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
.
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
200mm
342-455mm C3-BC5SLEEVE
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 452 to 620mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
464 to 632mm
CompositionBC-5 pedestal + 2x Sleeve C3-BC5 + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-9-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 2x)Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-9-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-9-INV.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 620 1277 2847 1/2 620 1023 2282 1/4 620 723 1613
Safety value for maximum allowable load by compression for BC-9-INV:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-9-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
145mmBC-9-INV
145mm
205mm
464-632mm
BC-9-INV + BC-PH5
Technical data sheet
BC-9-INV
- adjustable from 452 to 620mm
BC-PH5 SLOPE CORRECTOR
BC-5-BASE
BC-5 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
.
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
200mm
452-620mm
C3-BC5SLEEVE
C3-BC5SLEEVE
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 562 to 790mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
574 to 802mm
CompositionBC-5 pedestal + 3x Sleeve C3-BC5 + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-10-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 3x)Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-10-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-10-INV.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 790 1197 2669 1/2 790 917 2044 1/4 790 620 1383
Safety value for maximum allowable load by compression for BC-10-INV:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-10-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
145mm
BC-10-INV 145mm
205mm
574-802mm
BC-10-INV + BC-PH5
Technical data sheet
BC-10-INV
- adjustable from 562 to 790mm
BC-PH5 SLOPE CORRECTOR
BC-5-BASE
BC-5 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
.
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems..
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
200mm
562-790mm
C3-BC5SLEEVE
C3-BC5SLEEVE
C3-BC5SLEEVE
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 672 to 995mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
684 to 1007mm.
CompositionBC-5 pedestal + 4x Sleeve C3-BC5 + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-11-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 4x)Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-11-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-11-INV.
Accessories� Independent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 995 1165 2598 1/2 995 932 2078 1/4 995 615 1371
Safety value for maximum allowable load by compression for BC-11-INV:� Safety for pedestrian terraces: divide the load indicated in thetable by 2 with a safety factor of - 15 %.� Safety for technical floors: divide the load indicated in the table by 4 with a safety factor of - 15 %Note : The BUZON BC-11-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
145mm
BC-11-INV 145mm
205mm
684-1007mm
BC-11-INV + BC-PH5
Technical data sheet
BC-11-INV
- adjustable from 672 to 995mm
BC-PH5 SLOPE CORRECTOR
BC-5-BASE
BC-5 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
� Shim: Enhances acoustic
performance and can help
to level uneven paving materials.
� Joist support: Supports timber,
aluminium or composite battens
for most decking systems.
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
200mm
672-995mm
C3-BC5SLEEVE
C3-BC5SLEEVE
C3-BC5SLEEVE
C3-BC5SLEEVE
3mm
17mm
17mm
4.5mm3mm
4.5mm
Adjustable heightAdjustable height from 782 to 1120mm uninterrupted.
With addition of a 0 to 5% slope corrector BC-PH5, adjustable from
794 to 1132mm.
CompositionBC-5 pedestal + 5x Sleeve C3-BC5 + 1x Inverter C4-BC-INV.
MaterialCopolymer polypropylene (CPP), material thickness 3 to 4.5mm
Composition: 80% recycled PPC, 20% talc and UV black
masterbatch, 100% recyclable.
Dimensions of the BC-12-INV pedestalHead = diameter 145mm – Surface area 165cm2
Base = diameter 200mm – Ground surface 315cm2
Sleeve = diameter 105mm – Height 184mm (Qty = 5x)Inverter = Internal diameter 105mm – Adjustable height + 34mm
(Qty = 1x)
PerformancesResisting UV rays, weather, sea salt and almost all chemicals
Temperature range: -30° to + 90°
ApplicationsSupport for outdoor terraces with any kind of materials: timber
decking, stone, ceramic, composite materials, metal, fiberglass
grid…Can be placed on any stable substrate, also over insulation
panels.
Slope corrector BC-PH-5 from 0 to 5% Slope corrector B C-PH5 is placed under the base of pedestal
BC-12-INV. Consisting of 2 cylindrical parts, it allows to
compensate for 1 to 5% slopes by simply rotating the devices.
Thickness of BC-PH-5 = + 12 mm to be added to the ajdustable
height of pedestal BC-12-INV.
Accessories�� ,ndependent tabs : Material in polyamide, tabs available in
2-3-4.5-6-8-10mm thickness to achieve an open gap between pavers.
Compression test (1daN = 1Kg/f = 2,23lbf)
Performed on the full (1/1), half (1/2) or quarter (1/4) surfaceof the head.Position Height(mm) Breaking Breaking Load(daN) Load(lbf) 1/1 1120 1092 2434 1/2 1120 867 1933 1/4 1120 673 1502
Safety value for maximum allowable load by compression for BC-12-INV:��6DIHW\�IRU�SHGHVWULDQ�WHUUDFHV��GLYLGH�WKH�ORDG�LQGLFDWHG�LQ�WKHtable by 2 with a safety factor of - 15 %.�� 6DIHW\� IRU� WHFKQLFDO� IORRUV�� GLYLGH� WKH� ORDG� LQGLFDWHG� LQ� WKH� WDEOH� E\� ��ZLWK� D�safety factor of - 15 %Note : The BUZON BC-12-INV pedestals in polypropylene are not designed to support machinery or equipment subject to vibration.
Buzon Pedestal International s.a./ n.v. Z.I. des Hauts-Sarts, Zone 1 - Prolongement de la rue de l'Abbaye, 134 - B-4040 Herstal - Belgium
Tel +32 (0)4 248 39 83 Fax +32 (0)4 264 82 38 E-Mail [email protected] www.buzon.eu
0%
0 to 5%
SLOPE CORRECTOR
BC-PH5
BC-12-INV
145mm
205mm
794-1132mm
BC-12-INV + BC-PH5
Technical data sheet
BC-12-INV
- adjustable from 782 to 1120mm
BC-PH5 SLOPE CORRECTOR
BC-5-BASE
BC-5 TOP
C4-BC-INVINVERTER
Rectangular tabs
2mm 4.5mm 6mm 8mm 10mm
Circular tabs
2mm 4.5mm 6mm 8mm 10mm
1mm and 2mm
thickness
EPDM -60 Shore
25mm
25mm
���6KLP� Enhances acoustic
performance and can help
to level uneven paving materials.
���-RLVW�VXSSRUW� Supports timber,
aluminium or composite battens
for most decking systems.
The adjustable guide
allows a joist (width
between 35 and 90 mm)
Made in CPP
200mm
782-1120mm
C3-BC5SLEEVE
C3-BC5SLEEVE
145mm
C3-BC5SLEEVE
C3-BC5SLEEVE
C3-BC5SLEEVE
3mm
17mm
17mm
4.5mm3mm
4.5mm
