Upload
others
View
39
Download
1
Embed Size (px)
Citation preview
BACKHOE LOADER | 3DX SUPER
STATIC DIMENSIONS
Dimensions in metres (ft-in) 3DX Super
A Total travel length 5.96 (19-3)
B Wheelbase 2.24 (7-1)
C Slew centre to rear axle centre 1.36 (4-6)
D Minimum ground clearance (stabiliser foot clearance) 0.36 (1-2)
E Slew ground clearance 0.53 (1-8)
F Cab roof height 2.87 (9-4)
G Total travel clearance 3.61 (11-10)
H Shovel width 2.23 (7-3)
J Rear frame width 2.24 (7-4)
A
B
DE
F
G
H
J C
LOADER END MAX. PAYLOAD: 1850 kg (4078 lb) MAX. LIFT HEIGHT: 3.23 metres (10.59 ft)
BACKHOE LOADER | 3DX SUPER
A
J
EHC
F
D
C
B
G
A
J
EHC
F
D
C
B
G
U T
MN O
P
Q
RS
V
EXCAVATOR PERFORMANCE
3DX Super
A Max dig depth 4.77 (15-7)
B Reach-ground level to rear wheel centre 6.72 (22-1)
C Reach-ground level to slew centre 5.40 (17-9)
D Reach at full height to slew centre 2.74 (9-10)
E Side reach to centre line of machine 6.02 (19-9)
F Max. working height 5.97 (19-6)
G Max. load over height 4.18 (13-7)
H King post travel 1.06 (3-5)
J Bucket rotation – power 185°
Bucket tearout force 5700kgf
Dipper tearout force 3010kgf
Lift capacity to bucket pivot 1490kg
LOADER PERFORMANCE
3DX Super
M Dump height 2.72 (8-11)
N Load over height 3.23 (10-7)
O Pin height 3.45 (11-4)
P Pin forward reach 0.36 (1-2)
Q Reach at ground 1.40 (4-6)
R Max. reach at full height 1.15 (3-9)
S Reach at full height – bucket dumped 0.78 (2-7)
T Below ground level dig depth 0.10 (0-4)
U Rollback at ground 45°
V Dump angle 43°
Bucket breakout force 6500kgf
Loader arm breakout force 4850kgf
Shovel capacity 1.0m³ (6-in-1 shovel) / 1.1m3 (GP shovel)
BACKHOE LOADER | 3DX SUPER
ENGINE (BS III Emissions)
Machine 3DX Super
Model JCB Dieselmax 444
Aspiration Turbocharged
No. of cylinders 4
Displacement 4.4 litre
Gross power @ 2200rpm 68kW (92hp)
Max torque 408Nm @ 1200rpm
Service: Hydraulically actuated dual line, self adjusting, oil immersed, multi-disc type on the rear axle, well protected from dirt, water etc. requiring no maintenance.Parking: Hand operated, disc brake on rear axle input disc.Brake pedal: Two independently operable foot pedals enable machine to manoeuvre in tight spaces. Pedals are linked
together for normal use.Option for 4WD: Option exists on the machine to automatically switch from 2WD to 4WD for effective transmission braking.
BRAKES
• JCB vari-matic hydraulics • Main relief valve: 3300psi (228bar) • Unloader valve: 3000psi (207bar) • Pump type: 2 section displacement gear • Pump capacity: 110 lpm • Filtration through suction strainer and return line JCB Filtermatic filter • During excavation the circuit automatically varies hydraulic power to match digging conditions for extra performance, control and power • Careful routing of hydraulic hoses and pipework guards against site damage and allows easy servicing
HYDRAULIC SYSTEM
front wheel full power hydrostatic system utilising the main hydraulic pump via a steering priority valve. In the event of engine failure, emergency steering is maintained (all models).
STEERING
Inner wheels brakedA Outside loader bucket 9.79mB Outside wheels 7.21m
Inner wheels not brakedA Outside loader bucket 10.91mB Outside wheels 8.32m
TURNING CIRCLE
Machine model 3DX Super (4WD)
Manufacturer JCB
Type Synchroshuttle
Torquelock N/A
Gears forward/reverse 4 forward/2 reverse
Shuttle control – F/R Power shuttle
Travel speeds* kph (mph)
Gear 1 7.3
Gear 2 11.7
Gear 3 22.0
Gear 4 40.0
*Speeds may vary dependant on tyre selection.
JCB Synchro-shuttle transmission: It provides superb drive power in all conditions. It consists of a 4-speed, full synchromesh gearbox with integral torque convertor and electrically operated reversing power shuttle.• Easy-to-use, column mounted electric reversing shuttle which can change machine direction while allowing operator to keep hands on the steering wheel leading to fast cycle times.• The pedal layout and conventional 4-pattern gear lever with transmission disconnect switch adds to the overall ease of
operation. On-the-move gear changes are possible.• Torque convertor stall ratio is 2.52:1 (4WD)
TRANSMISSION
Machine model 3DX SUPER
ltr
Cooling system 16.5
Fuel tank 128
Engine oil with filter 14
Gearbox with filter 16
Rear axle 21
Front axle 11
Hydraulic system incl. tank 130
SERVICE CAPACITIES
Rear: Drive axle rigidly mounted, incorporates JCB Max-Trac torque proportioning differential, driven by short propshaft from gear box.Front: 4WD, Steer axle, centrally pivoted with oscillation angle of 16°.
AXLES
12 volt negative ground, utilising wiring and connectors meeting IP69 water ingress test standard. Central fuse panel.Battery: 130 A/hrAlternator: 65 amp standard.Front working lights 2 fixed.Rear working lights 2 fixed and 2 adjustable.
ELECTRICAL AND INSTRUMENTATION
Front: 12.5x18-12PR (4WD)Rear: 16.9x28-12PR (4WD)
TYRES
Shipping: 7660 kgOperating: 7800 kg
WEIGHT
• Floormats• Fully adjustable seat and soft touch steering wheel • ‘Walk through’ two door access • Seat belt, large convex rear view mirror, interior light front screen wiper, horn, hazard warning system, tool box, passenger seat • Instrumentation panel includes engine speed, engine hours, fuel level, water temperature gauge and mobile charger • Audible and visual fault warning system for alternator charge, coolant temperature, engine oil pressure, blocked air filter, transmission oil pressure and temperature, and hand brake on.
CAB
BACKHOE LOADER | 3DX SUPER
JCB Sales Limited, Rocester, Staffordshire ST14 5JP. Tel: 01889 590312. Web: http://www.jcb.com
JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. The JCB logo is a registered trademark of J C Bamford Excavators Ltd. 9999/5619 04/12 Issue 1