Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
BabyLabs24-october-2018
SmallOnleyLabyrinths/Transmission LinesfortheFostexFF85wk/FF105wk/FE103 SOL,MarkAudioAlpair5.2,Alpair6.2p/Alpair6.2m,CHN-70,Pluvia7,andAuraNS3-193
Intendedfordesktopusebutoftenusesassmallstandmounts.
Freefornon-commercial use.
*©2010-2018WodenDesignFreefornon-commercialuse,commerciallicencingavailable
Notes 1: Baby Lab Examples23-april-2018
*© 2010-2018 Woden DesignFree for non-commercial use, commercial licencing available
Falcon | Jeff Drouin, Tulsa, Ok Shrike | Jeff Drouin, Tulsa, Ok Shrike | toobhead
Lance | nemonis
Stinger | planet10-hifi, Victoria, BC Falcon | planet10-hifi, Victoria, BC
Bloodhound Prototypes | Chris Bobiak, Victoria, BCRed Eye | Mike Jennens, Bismarck, ND / Jerms, Bucks, UK
Notes: Baby Labs23-april-2018
*© 2010-2018 Woden DesignFree for non-commercial use, commercial licencing available
Example Falcon Build
The LanceFF85wk Labyrinth TL 1v02Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-14 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine
273.1[10 3/4]
203.3[8]
247.7[9 3/4]
177.9[7]
127[5]
101.6[4]
76.3[3]
50.8[2]
25.4[1]
50.8[2]
25.4[1]
25.4[1]
82.6[3 1/4]
3
The LanceFF85wk Labyrinth TL 1v02Damping | 19-january-2015designed by Scott Lindgren | drawn by dld© 2010-15 Woden DesignFree for non-commercial use
Notes:0/ damp top (1) & back (4) of 1st manifold, & one side (5) down to just below the driver. Bottom of 1st & 2nd manifold (2), top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent
4
5
2
112
3 3
4 5
5
1
76.3[3]
89[3 1/2]
140[5 1/2]
165[6 1/2]
470.3[18 17/32]
65[2 9/16]
101.6[4]
110[4 11/32]
FalconFF105wk Labyrinth TL 1v0Plan 1/2" | 23-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2" (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine
279.4[11]
273.2[10 3/4]
254[10]
247.8[9 3/4]
152.4[6]
127[5]
127.1[5]
63.5[2 1/2]
25.4[1]
63.5[2 1/2]
31.8[1 1/4]
31.8[1 1/4]
63.5[2 1/2]
4 53
FalconFF105wk Labyrinth TL 1v02Damping | 23-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use
Notes:0/ damp top (1) & back (4) of 1st manifold, & one side (5) down to just below the driver. Bottom of 1st & 2nd manifold (2), top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent
140[5 1/2]
179[7 1/32]
646[25 13/32]
3
3
5
1
4
2 1
5
3
2
109[4 9/32]
108[4 1/4]
127[5] 1
110[4 11/32]
ShrikeFE103 Sol Labyrinth TL 0v82Plan 1/2" | 24-april-2018designed by Scott Lindgren | drawn by dld© 2010-18 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2" (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2" ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine
304.8[12]
304.8[12]
279.4[11]
279.4[11]
158.8[6 1/4]
133.4[5 1/4]
127.1[5]
85.7[3 3/8]
41.2[1 5/8]
108[4 1/4]
57.2[2 1/4]
41.3[1 5/8]
69.9[2 3/4]
BloodhoundAlpair 5.2 Labyrinth TL 0v99Plan 1/2” | 08-october-2015designed by Scott Lindgren | drawn by dld© 2010-15 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine
279.4[11]
197[7 3/4]
254[10]
171.6[6 3/4]
139.7[5 1/2]
114.3[4 1/2]
76.3[3]
50.8[2]
19.1[3/4]
50.8[2]
19.1[3/4]
19.1[3/4]
69.9[2 3/4]
The StingerAlpair 6.2p/m Labyrinth TL 1v0Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-2014 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2” (12.7mm) material. Due to thick bezel, 15mm or 5/8” baffle is suggested.1/ Damping: all faces 1st manifold leaving adequate breathing room for driver on front baffle. Top and bottom of 2nd manifold, + 2 non-opposing faces. Bottom of 3rd manifold + 2 non opposing faces for ~5in. Final few inches un-damped to preserve most of fundamental.2/ original design specification is imperial, minor adjustments formetric are fine3/ relieve the back of the driver cutout to ensure good breathing for the back of the cone.
279.4[11]
228.7[9]
254[10]
203.3[8]
165.1[6 1/2]
139.7[5 1/2]
101.7[4]
50.8[2]
25.4[1]
50.8[2]
25.4[1]
25.4[1]
63.5[2 1/2]
SkyflashCHN-70LabyrinthTL0v9Plan1/2”|24-october-2018designedbyScottLindgren|drawnbydld©2010-18WodenDesignFreefornon-commercialuse
Notes:0/drawnusing1/2”(12.7mm)material1/damptop&backof1stmanifold,&onesidedowntojustbelowthedriver.Bottomof1st&2ndmanifold,topof2nd&3rdmanifold&adjustfromthereifneededwith1/2”ultratouchfeltorequivalent2/originaldesignspecificationisimperial,minoradjustmentsformetricarefine
304.8[12]
273.2[103/4]
279.4[11]
247.8[93/4]
165.1[61/2]
139.7[51/2]
127.1[5]
63.5[21/2]
31.8[11/4]
63.5[21/2]
31.8[11/4]
31.8[11/4]
92.1[35/8]
StormShadowMarkAudioPluvia7LabyrinthTL0v81Plan1/2”|24-october-2018designedbyScottLindgren|drawnbydld©2010-18WodenDesignFreefornon-commercialuse
Notes:0/drawnusing1/2”(12.7mm)material1/damptop&backof1stmanifold,&onesidedowntojustbelowthedriver.Bottomof1st&2ndmanifold,topof2nd&3rdmanifold&adjustfromthereifneededwith1/2”ultratouchfeltorequivalent2/originaldesignspecificationisimperial,minoradjustmentsformetricarefine
323.9[123/4]
273.2[103/4]
298.5[113/4]
247.8[93/4]
158.8[61/4]
133.4[51/4]
127.1[5]
63.5[21/2]
31.8[11/4]
63.5[21/2]
31.8[11/4]
31.8[11/4]
101.8[4]
RedeyeAura NS3-193-8A Labyrinth TL 1v02Plan 1/2” | 14-december-2014designed by Scott Lindgren | drawn by dld© 2010-14 Woden DesignFree for non-commercial use
Notes:0/ drawn using 1/2” (12.7mm) material1/ damp top & back of 1st manifold, & one side down to just below the driver. Bottom of 1st & 2nd manifold, top of 2nd & 3rd manifold & adjust from there if needed with 1/2” ultratouch felt or equivalent2/ original design specification is imperial, minor adjustments formetric are fine
304.8[12]
228.6[9]
279.4[11]
203.3[8]
127[5]
101.6[4]
101.7[4]
50.8[2]
25.4[1]
50.8[2]
25.4[1]
25.4[1]
88.9[3 1/2]
82[3 7/32]
71[2 25/32]
65[2 9/16]
45[1 25/32]
Fostex FF85wkDimensions 0v9
16-october-2016 | drawn by D Dlugos© 2009-2016 planet_10 enterprises limited
3.4[1/8]
107[4 7/32]
92[3 5/8]
85[3 11/32]
51[2]
Fostex FF105wkDimensions 0v91
19-april-2018 | drawn by D Dlugos© 2009-2018 planet_10 enterprises limited
for licenced use only
2.5[3/32]
Ø115[Ø4 17/32]
Fostex FE103 SolDimensions 0v9
24-april-2018 | designed & drawn by D Dlugos© 2009-2016 planet_10 enterprises limited
for licenced use only
107[4 7/32]
92[3 5/8]
80[3 5/32]
47[1 27/32]
2.5[3/32] 5x7mmØ114
[Ø4 1/2]
100[3 15/16]
6[1/4]
39[1 17/32]
61[2 13/32]
78[3 1/16]
Alpair 5.xdriver dimensionsdrawn by dld | 19-march-2016
114[4 1/2]
6.1[0]
52[2]
93[3 1/2]
Alpair 6Alpair 6.2P | 6.2Mdriver dimensionsdrawn by dld | 14-nov-2017
Alpair 6.2: orient with Mark Audio logo at the top
103[4]
allow ~1 mm for gasket
100[3 15/16]
122.3[4 13/16]
4.5[3/16]
58[2 9/32]
Pluvia Seven / CHS-70
driver dimensionsdrawn by dld | 14-november-2017
70[2 3/4]
112[4 13/32]
allow ~1 mm for gasket
3[1/8]
Aura NS3Dimensions 0v9
24-april-2018 | drawn by D Dlugos© 2009-2018 planet_10 enterprises limited
for licenced use only
103.5[4 1/16]
36[1 13/32]
75.5[2 31/32]
54.9[2 5/32]
Ø93[Ø3 21/32]
Ø4.3[Ø5/32]