The Ultimate Moisture and Corrosion Protection.GE’s water-cooled motor is completely enclosed and protected, to IP56 standards, against moisture, insects or dirt from being sucked into the motor – especially in harsh, offshore environments. These elements can cause corrosion, wear down windings, and even shut down the motor.

A safer more cost-efficient motor, GE’s water-cooled drill motor has no blower. No blower means one less power supply and far less rig noise. Less noise on the rig floor, below OSHA requirements, means a safer environment for those working on the rig.

Rated at 1150HP, the GE water-cooled motor has a small envelope. And, because it cools through the shaft as well as the frame, it maintains the same footprint as our air-cooled models, and can be easily incorporated onto the rig.

Year after year, GE has built thousands of AC and DC traction motors for the drilling industry. For decades, these motors have been engineered, manufactured and tested to GE’s most stringent standards in the harshest drilling environments.

To better serve its customers, GE has established a worldwide network of authorized service facilities for both its AC and DC drilling motors. These service facilities are audited and GE’s personnel have been trained to assure that they meet the quality standards required to repair GE’s drilling motors.

Model 5GE752ARB1 (New)5GE752ARB2 5GE752ARB3 5GE752RB1 (New)

5GE752RB2 5GE752RB3 5GE752AUT2 5GE752US2

Type HorizontalSeries Wound

HorizontalSeries Wound

HorizontalSeries Wound

HorizontalShunt Wound

HorizontalShunt Wound

HorizontalShunt Wound

VerticalSeries Wound

VerticalShunt Wound

Application Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks Top Drive Top Drive

Available Certifications ABS ATEX, ABS ABS ATEX, ABS ABS ABS

Max. Continuous HP 1085 1085 1085 1130 1130 1130 1085 1130

Full Load RPM 965 965 965 1040 1040 1040 965 1040

Maximum RPM 2300 2300 2300 2300 2300 2300 2300 2300

Full Load Current 1150 1150 1150 1185(60 amp field)

1185(60 amp field)

1185(60 amp field) 1150 1185

(60 amp field)

Torque (at base rpm) 5900 5900 5900 5705 5705 5705 5900 5705

Voltage 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc

Inertia (lbft2) 552 552 552 552 552 552 552 552

Approximate Weight (lbs) 7200 7200 7200 7200 7200 7200 6720 6720

GE Transportation

DC Models

AC ModelsModel 5GEB22A 5GEB22D 5GEB22E 5GEB20B 5GEB28A 5GEB29A 5GEB27A 5GEB1150W**

Type Horizontal Horizontal Horizontal Vertical Horizontal Horizontal Vertical Horizontal/Vertical

Application Drawworks,Mud Pump

Side-LoadMud Pump

Axial-LoadDrawworks Top Drive Axial Load

DrawworksSide-LoadMud Pump Top Drive Top Drive

Drawworks

Available Certifications* ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS

Max. Continuous HP 1150 1150 1150 1150 1500 1500 1500 1150

Full Load RPM 800-1800 800-1800 800-1800 800-1800 900-1200 900-1200 900-1200 800-1600

Maximum RPM 3000 3000 3000 2300 3000 3000 2300 3000

Full Load Current 1120 1120 1120 1120 1360 1360 1360 1080

Torque (at base rpm) 7550 7550 7550 7550 8750 8750 8750 7550

Voltage 587 vac 587 vac 587 vac 587 vac 577 vac 577 vac 577 vac 587 vac

Inertia (lbft2) 429 429 429 429 767 767 767 524

Approximate Weight (lbs) 6500 6500 6500 6000 8500 8500 7878 7600

20185-A

Experience and ReliabilityAC and DC Drilling Motor Solutions for the Future

AC motor offshore features: ATEX certification Ex II T3, II 2G c by Sira; spark-less heavy-duty blower assembly; blower motor rated for hazardous locations; 6-pole stator with form-wound windings; Class H insulation with superior GE VPI process; 100-ohm platinum RTDs embedded in the stator windings; insulated bearing on the non-drive end of the motor; pressure sensor; space heater; IP44 louvered air intake panels; stainless steel IP56 connection box, IP44 motor rating.

AC motor land features: Motor not available with ABS or ATEX certification. Includes hood style blower air intake, painted carbon steel connection box and IP23 motor rating.

*DNV certification available as an option ** ATEX certification Ex de II T4 Gb IP56, de II 2G c by Sira

Now available with ATEX certification Ex px de IIC T3 II 2G by Baseefa; blower motors rated for hazardous locations; pressurized connection box with double bolt-on cable connection; pressure sensor to verify ventilation; sparkless 10hp heavy-duty blower; intake hood that protects against blowing rain, Class H insulation; auxiliary lockout switch; space heater; optional marine features (ABS-certified shaft; armored cables; two 100-ohm platinum RTDs).

Visit us online at gedrillingpower.com

Now for more than two decades, GE has supplied thousands of AC traction motors for land and offshore drilling rigs world-wide. Offered in both horizontal and vertical configurations, the 1150HP and 1500HP AC motors will meet the most stringent requirements of your drilling equipment. Design features include: heavy-duty frames; form-wound stator windings; high-strength rotor assemblies; and GE’s low-inertia rotor.

GE AC Motor AdvantagesGreater torque and speed.GE’s AC drilling motors produce more torque at both low and high speeds than a DC counterpart. Maximum speed for a GE horizontal AC motor is 3,000 rpm.

Low inertia rotor.A low inertia rotor enhances the drawworks performance by providing highly responsive acceleration, reduced braking time and less wasted energy. The lower weight and inertia of the rotor is achieved through a design that optimizes current and flux densities.

GE Drilling Motors – Choose an Industry LeaderGE manufactures rugged electric motors for the toughest applications in the oil and gas industry. Since shipping its first DC drilling motor in 1955, GE has pioneered the electrification of the drilling rig and continues today to lead the way in manufacturing DC and AC drilling motors for land and offshore drilling rigs.

Engineered, manufactured and tested to withstand the harshest requirements, you can’t go wrong choosing a GE drilling motor. Thousands of GE motors in use today have proven time and again their ability to continually meet or exceed customer expectation driving drawworks, mud pumps, cement pumps, rotary tables, top drives, and anchor-handling winches on all types of drilling rigs, all over the world.

More Advantages from the Industry’s Leader in Powering the Drilling Industry.Working to meet our customers’ requirements, GE’s ongoing research and development efforts to provide innovative and increasingly efficient technology continue to produce electric motors that are a more reliable and efficient power supply – especially in extreme weather conditions – and able to decrease noise on the rig, making a safer working environment. Combined with a potentially smaller “envelope,” this makes GE motors a better solution to meeting your rigs’ power supply requirements.

Engineered and Time-Tested for Dependable Operation Around the World.How important is your rig’s continued operation? What is the cost of your operations shutting down for a day? On land or offshore, that’s a cost you can’t afford.

GE’s AC Motors

5GEB22 1150 HP horizontal AC drilling motor

Rugged, heavy-duty frame absorbs the high torque and pounding condi-tions present in drilling applications.

Form-wound windings, GE’s superior Class H insulation and VPI application process provides superior protection from winding failures because of voltage spikes.

copper chromium alloy rotor bars and brazed end turns increase the reliability and life of the rotor assembly.

is standard on all horizontal AC motors. Optional oversized shaft extension and hub are available for belt-driven applications.

provides IP56 protection certified to ATEX standards by Sira. Closed cooling system provides maximum protection to motor windings from airborne contaminants and moisture. TEWAC configurations are available with both 1150 HP and 1500 HP motors. a space heater to apply heat directly to

AC Drilling Motor Design Highlights

stator windings to help remove mois-ture. This centralized approach with tape heaters being wound into the endturns of the motor (most susceptible place for moisture) provides 200 watts on each end totaling 400 watts. Provisions have been provided on both sides of the motor for connection box mounting. The new optional heater upgrade eliminates the need for a separate auxiliary box.

GE shipped the first 752 DC motor for a drilling rig in 1955. For more than 55 years, GE has provided dependable 752 DC drilling motors for the toughest drilling applications. GE is continuing its tradition of providing high-quality, reliable drilling motors for land and offshore drilling rigs worldwide.

GE DC Motor AdvantagesProven performance.No guesswork required. The performance characteristics of GE’s original 752 DC drilling motors have been proven time and time again on all major drill rig operations. The motor performance on GE’s original 752 DC drilling motors has continually met or exceeded customer requirements.

Dependable operation, backed by GE.Thousands of GE’s original 752 DC drilling motors are performing worldwide on all types of drill rigs, providing dependable operations of the rig’s primary equipment. The 752 DC drilling motors have been reported by rig operators to run for years without service or failure.

GE’s DC Motors

GE’s 752 DC horizontal drilling motor

DC Drilling Motor Design Highlights

GE’s original 752 drilling frames and coils are built to last for years. No other manufacturing is licensed by GE. Ask for ORIGINAL GE frames and coils. Do not accept imposters.

GE’s original 752 high torque armature and commutatorwere designed exclusively for 752 high torque motors to reduce heat and increase torque. Excessively worn and smaller commutators found on many used armatures can increase maintenance expense by shortening brush life and increasing the risk of flashover.

4340 alloy steel shafts have been provided on all horizontal DC motors since 2002. Today’s demanding applications with high-tension belted loads require strengthened shafts. Beware of used 752 and locomotive armatures equipped with standard carbon steel shafts.

The Ultimate Moisture and Corrosion Protection.GE’s water-cooled motor is completely enclosed and protected, to IP56 standards, against moisture, insects or dirt from being sucked into the motor – especially in harsh, offshore environments. These elements can cause corrosion, wear down windings, and even shut down the motor.

A safer more cost-efficient motor, GE’s water-cooled drill motor has no blower. No blower means one less power supply and far less rig noise. Less noise on the rig floor, below OSHA requirements, means a safer environment for those working on the rig.

Rated at 1150HP, the GE water-cooled motor has a small envelope. And, because it cools through the shaft as well as the frame, it maintains the same footprint as our air-cooled models, and can be easily incorporated onto the rig.

Year after year, GE has built thousands of AC and DC traction motors for the drilling industry. For decades, these motors have been engineered, manufactured and tested to GE’s most stringent standards in the harshest drilling environments.

To better serve its customers, GE has established a worldwide network of authorized service facilities for both its AC and DC drilling motors. These service facilities are audited and GE’s personnel have been trained to assure that they meet the quality standards required to repair GE’s drilling motors.

Model 5GE752ARB1 (New)5GE752ARB2 5GE752ARB3 5GE752RB1 (New)

5GE752RB2 5GE752RB3 5GE752AUT2 5GE752US2

Type HorizontalSeries Wound

HorizontalSeries Wound

HorizontalSeries Wound

HorizontalShunt Wound

HorizontalShunt Wound

HorizontalShunt Wound

VerticalSeries Wound

VerticalShunt Wound

Application Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks Top Drive Top Drive

Available Certifications ABS ATEX, ABS ABS ATEX, ABS ABS ABS

Max. Continuous HP 1085 1085 1085 1130 1130 1130 1085 1130

Full Load RPM 965 965 965 1040 1040 1040 965 1040

Maximum RPM 2300 2300 2300 2300 2300 2300 2300 2300

Full Load Current 1150 1150 1150 1185(60 amp field)

1185(60 amp field)

1185(60 amp field) 1150 1185

(60 amp field)

Torque (at base rpm) 5900 5900 5900 5705 5705 5705 5900 5705

Voltage 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc

Inertia (lbft2) 552 552 552 552 552 552 552 552

Approximate Weight (lbs) 7200 7200 7200 7200 7200 7200 6720 6720

GE Transportation

DC Models

AC ModelsModel 5GEB22A 5GEB22D 5GEB22E 5GEB20B 5GEB28A 5GEB29A 5GEB27A 5GEB1150W**

Type Horizontal Horizontal Horizontal Vertical Horizontal Horizontal Vertical Horizontal/Vertical

Application Drawworks,Mud Pump

Side-LoadMud Pump

Axial-LoadDrawworks Top Drive Axial Load

DrawworksSide-LoadMud Pump Top Drive Top Drive

Drawworks

Available Certifications* ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS

Max. Continuous HP 1150 1150 1150 1150 1500 1500 1500 1150

Full Load RPM 800-1800 800-1800 800-1800 800-1800 900-1200 900-1200 900-1200 800-1600

Maximum RPM 3000 3000 3000 2300 3000 3000 2300 3000

Full Load Current 1120 1120 1120 1120 1360 1360 1360 1080

Torque (at base rpm) 7550 7550 7550 7550 8750 8750 8750 7550

Voltage 587 vac 587 vac 587 vac 587 vac 577 vac 577 vac 577 vac 587 vac

Inertia (lbft2) 429 429 429 429 767 767 767 524

Approximate Weight (lbs) 6500 6500 6500 6000 8500 8500 7878 7600

20185-A

Experience and ReliabilityAC and DC Drilling Motor Solutions for the Future

AC motor offshore features: ATEX certification Ex II T3, II 2G c by Sira; spark-less heavy-duty blower assembly; blower motor rated for hazardous locations; 6-pole stator with form-wound windings; Class H insulation with superior GE VPI process; 100-ohm platinum RTDs embedded in the stator windings; insulated bearing on the non-drive end of the motor; pressure sensor; space heater; IP44 louvered air intake panels; stainless steel IP56 connection box, IP44 motor rating.

AC motor land features: Motor not available with ABS or ATEX certification. Includes hood style blower air intake, painted carbon steel connection box and IP23 motor rating.

*DNV certification available as an option ** ATEX certification Ex de II T4 Gb IP56, de II 2G c by Sira

Now available with ATEX certification Ex px de IIC T3 II 2G by Baseefa; blower motors rated for hazardous locations; pressurized connection box with double bolt-on cable connection; pressure sensor to verify ventilation; sparkless 10hp heavy-duty blower; intake hood that protects against blowing rain, Class H insulation; auxiliary lockout switch; space heater; optional marine features (ABS-certified shaft; armored cables; two 100-ohm platinum RTDs).

Visit us online at gedrillingpower.com

Now for more than two decades, GE has supplied thousands of AC traction motors for land and offshore drilling rigs world-wide. Offered in both horizontal and vertical configurations, the 1150HP and 1500HP AC motors will meet the most stringent requirements of your drilling equipment. Design features include: heavy-duty frames; form-wound stator windings; high-strength rotor assemblies; and GE’s low-inertia rotor.

GE AC Motor AdvantagesGreater torque and speed.GE’s AC drilling motors produce more torque at both low and high speeds than a DC counterpart. Maximum speed for a GE horizontal AC motor is 3,000 rpm.

Low inertia rotor.A low inertia rotor enhances the drawworks performance by providing highly responsive acceleration, reduced braking time and less wasted energy. The lower weight and inertia of the rotor is achieved through a design that optimizes current and flux densities.

GE Drilling Motors – Choose an Industry LeaderGE manufactures rugged electric motors for the toughest applications in the oil and gas industry. Since shipping its first DC drilling motor in 1955, GE has pioneered the electrification of the drilling rig and continues today to lead the way in manufacturing DC and AC drilling motors for land and offshore drilling rigs.

Engineered, manufactured and tested to withstand the harshest requirements, you can’t go wrong choosing a GE drilling motor. Thousands of GE motors in use today have proven time and again their ability to continually meet or exceed customer expectation driving drawworks, mud pumps, cement pumps, rotary tables, top drives, and anchor-handling winches on all types of drilling rigs, all over the world.

More Advantages from the Industry’s Leader in Powering the Drilling Industry.Working to meet our customers’ requirements, GE’s ongoing research and development efforts to provide innovative and increasingly efficient technology continue to produce electric motors that are a more reliable and efficient power supply – especially in extreme weather conditions – and able to decrease noise on the rig, making a safer working environment. Combined with a potentially smaller “envelope,” this makes GE motors a better solution to meeting your rigs’ power supply requirements.

Engineered and Time-Tested for Dependable Operation Around the World.How important is your rig’s continued operation? What is the cost of your operations shutting down for a day? On land or offshore, that’s a cost you can’t afford.

GE’s AC Motors

5GEB22 1150 HP horizontal AC drilling motor

Rugged, heavy-duty frame absorbs the high torque and pounding condi-tions present in drilling applications.

Form-wound windings, GE’s superior Class H insulation and VPI application process provides superior protection from winding failures because of voltage spikes.

copper chromium alloy rotor bars and brazed end turns increase the reliability and life of the rotor assembly.

is standard on all horizontal AC motors. Optional oversized shaft extension and hub are available for belt-driven applications.

provides IP56 protection certified to ATEX standards by Sira. Closed cooling system provides maximum protection to motor windings from airborne contaminants and moisture. TEWAC configurations are available with both 1150 HP and 1500 HP motors. a space heater to apply heat directly to

AC Drilling Motor Design Highlights

stator windings to help remove mois-ture. This centralized approach with tape heaters being wound into the endturns of the motor (most susceptible place for moisture) provides 200 watts on each end totaling 400 watts. Provisions have been provided on both sides of the motor for connection box mounting. The new optional heater upgrade eliminates the need for a separate auxiliary box.

GE shipped the first 752 DC motor for a drilling rig in 1955. For more than 55 years, GE has provided dependable 752 DC drilling motors for the toughest drilling applications. GE is continuing its tradition of providing high-quality, reliable drilling motors for land and offshore drilling rigs worldwide.

GE DC Motor AdvantagesProven performance.No guesswork required. The performance characteristics of GE’s original 752 DC drilling motors have been proven time and time again on all major drill rig operations. The motor performance on GE’s original 752 DC drilling motors has continually met or exceeded customer requirements.

Dependable operation, backed by GE.Thousands of GE’s original 752 DC drilling motors are performing worldwide on all types of drill rigs, providing dependable operations of the rig’s primary equipment. The 752 DC drilling motors have been reported by rig operators to run for years without service or failure.

GE’s DC Motors

GE’s 752 DC horizontal drilling motor

DC Drilling Motor Design Highlights

GE’s original 752 drilling frames and coils are built to last for years. No other manufacturing is licensed by GE. Ask for ORIGINAL GE frames and coils. Do not accept imposters.

GE’s original 752 high torque armature and commutatorwere designed exclusively for 752 high torque motors to reduce heat and increase torque. Excessively worn and smaller commutators found on many used armatures can increase maintenance expense by shortening brush life and increasing the risk of flashover.

4340 alloy steel shafts have been provided on all horizontal DC motors since 2002. Today’s demanding applications with high-tension belted loads require strengthened shafts. Beware of used 752 and locomotive armatures equipped with standard carbon steel shafts.

Now for more than two decades, GE has supplied thousands of AC traction motors for land and offshore drilling rigs world-wide. Offered in both horizontal and vertical configurations, the 1150HP and 1500HP AC motors will meet the most stringent requirements of your drilling equipment. Design features include: heavy-duty frames; form-wound stator windings; high-strength rotor assemblies; and GE’s low-inertia rotor.

GE AC Motor AdvantagesGreater torque and speed.GE’s AC drilling motors produce more torque at both low and high speeds than a DC counterpart. Maximum speed for a GE horizontal AC motor is 3,000 rpm.

Low inertia rotor.A low inertia rotor enhances the drawworks performance by providing highly responsive acceleration, reduced braking time and less wasted energy. The lower weight and inertia of the rotor is achieved through a design that optimizes current and flux densities.

GE Drilling Motors – Choose an Industry LeaderGE manufactures rugged electric motors for the toughest applications in the oil and gas industry. Since shipping its first DC drilling motor in 1955, GE has pioneered the electrification of the drilling rig and continues today to lead the way in manufacturing DC and AC drilling motors for land and offshore drilling rigs.

Engineered, manufactured and tested to withstand the harshest requirements, you can’t go wrong choosing a GE drilling motor. Thousands of GE motors in use today have proven time and again their ability to continually meet or exceed customer expectation driving drawworks, mud pumps, cement pumps, rotary tables, top drives, and anchor-handling winches on all types of drilling rigs, all over the world.

More Advantages from the Industry’s Leader in Powering the Drilling Industry.Working to meet our customers’ requirements, GE’s ongoing research and development efforts to provide innovative and increasingly efficient technology continue to produce electric motors that are a more reliable and efficient power supply – especially in extreme weather conditions – and able to decrease noise on the rig, making a safer working environment. Combined with a potentially smaller “envelope,” this makes GE motors a better solution to meeting your rigs’ power supply requirements.

Engineered and Time-Tested for Dependable Operation Around the World.How important is your rig’s continued operation? What is the cost of your operations shutting down for a day? On land or offshore, that’s a cost you can’t afford.

GE’s AC Motors

5GEB22 1150 HP horizontal AC drilling motor

Rugged, heavy-duty frame absorbs the high torque and pounding condi-tions present in drilling applications.

Form-wound windings, GE’s superior Class H insulation and VPI application process provides superior protection from winding failures because of voltage spikes.

copper chromium alloy rotor bars and brazed end turns increase the reliability and life of the rotor assembly.

is standard on all horizontal AC motors. Optional oversized shaft extension and hub are available for belt-driven applications.

provides IP56 protection certified to ATEX standards by Sira. Closed cooling system provides maximum protection to motor windings from airborne contaminants and moisture. TEWAC configurations are available with both 1150 HP and 1500 HP motors. a space heater to apply heat directly to

AC Drilling Motor Design Highlights

stator windings to help remove mois-ture. This centralized approach with tape heaters being wound into the endturns of the motor (most susceptible place for moisture) provides 200 watts on each end totaling 400 watts. Provisions have been provided on both sides of the motor for connection box mounting. The new optional heater upgrade eliminates the need for a separate auxiliary box.

GE shipped the first 752 DC motor for a drilling rig in 1955. For more than 55 years, GE has provided dependable 752 DC drilling motors for the toughest drilling applications. GE is continuing its tradition of providing high-quality, reliable drilling motors for land and offshore drilling rigs worldwide.

GE DC Motor AdvantagesProven performance.No guesswork required. The performance characteristics of GE’s original 752 DC drilling motors have been proven time and time again on all major drill rig operations. The motor performance on GE’s original 752 DC drilling motors has continually met or exceeded customer requirements.

Dependable operation, backed by GE.Thousands of GE’s original 752 DC drilling motors are performing worldwide on all types of drill rigs, providing dependable operations of the rig’s primary equipment. The 752 DC drilling motors have been reported by rig operators to run for years without service or failure.

GE’s DC Motors

GE’s 752 DC horizontal drilling motor

DC Drilling Motor Design Highlights

GE’s original 752 drilling frames and coils are built to last for years. No other manufacturing is licensed by GE. Ask for ORIGINAL GE frames and coils. Do not accept imposters.

GE’s original 752 high torque armature and commutatorwere designed exclusively for 752 high torque motors to reduce heat and increase torque. Excessively worn and smaller commutators found on many used armatures can increase maintenance expense by shortening brush life and increasing the risk of flashover.

4340 alloy steel shafts have been provided on all horizontal DC motors since 2002. Today’s demanding applications with high-tension belted loads require strengthened shafts. Beware of used 752 and locomotive armatures equipped with standard carbon steel shafts.

The Ultimate Moisture and Corrosion Protection.GE’s water-cooled motor is completely enclosed and protected, to IP56 standards, against moisture, insects or dirt from being sucked into the motor – especially in harsh, offshore environments. These elements can cause corrosion, wear down windings, and even shut down the motor.

A safer more cost-efficient motor, GE’s water-cooled drill motor has no blower. No blower means one less power supply and far less rig noise. Less noise on the rig floor, below OSHA requirements, means a safer environment for those working on the rig.

Rated at 1150HP, the GE water-cooled motor has a small envelope. And, because it cools through the shaft as well as the frame, it maintains the same footprint as our air-cooled models, and can be easily incorporated onto the rig.

Year after year, GE has built thousands of AC and DC traction motors for the drilling industry. For decades, these motors have been engineered, manufactured and tested to GE’s most stringent standards in the harshest drilling environments.

To better serve its customers, GE has established a worldwide network of authorized service facilities for both its AC and DC drilling motors. These service facilities are audited and GE’s personnel have been trained to assure that they meet the quality standards required to repair GE’s drilling motors.

Model 5GE752ARB1 (New)5GE752ARB2 5GE752ARB3 5GE752RB1 (New)

5GE752RB2 5GE752RB3 5GE752AUT2 5GE752US2

Type HorizontalSeries Wound

HorizontalSeries Wound

HorizontalSeries Wound

HorizontalShunt Wound

HorizontalShunt Wound

HorizontalShunt Wound

VerticalSeries Wound

VerticalShunt Wound

Application Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks

Mud PumpDrawworks Top Drive Top Drive

Available Certifications ABS ATEX, ABS ABS ATEX, ABS ABS ABS

Max. Continuous HP 1085 1085 1085 1130 1130 1130 1085 1130

Full Load RPM 965 965 965 1040 1040 1040 965 1040

Maximum RPM 2300 2300 2300 2300 2300 2300 2300 2300

Full Load Current 1150 1150 1150 1185(60 amp field)

1185(60 amp field)

1185(60 amp field) 1150 1185

(60 amp field)

Torque (at base rpm) 5900 5900 5900 5705 5705 5705 5900 5705

Voltage 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc 750 vdc

Inertia (lbft2) 552 552 552 552 552 552 552 552

Approximate Weight (lbs) 7200 7200 7200 7200 7200 7200 6720 6720

GE Transportation

DC Models

AC ModelsModel 5GEB22A 5GEB22D 5GEB22E 5GEB20B 5GEB28A 5GEB29A 5GEB27A 5GEB1150W**

Type Horizontal Horizontal Horizontal Vertical Horizontal Horizontal Vertical Horizontal/Vertical

Application Drawworks,Mud Pump

Side-LoadMud Pump

Axial-LoadDrawworks Top Drive Axial Load

DrawworksSide-LoadMud Pump Top Drive Top Drive

Drawworks

Available Certifications* ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS ATEX, ABS

Max. Continuous HP 1150 1150 1150 1150 1500 1500 1500 1150

Full Load RPM 800-1800 800-1800 800-1800 800-1800 900-1200 900-1200 900-1200 800-1600

Maximum RPM 3000 3000 3000 2300 3000 3000 2300 3000

Full Load Current 1120 1120 1120 1120 1360 1360 1360 1080

Torque (at base rpm) 7550 7550 7550 7550 8750 8750 8750 7550

Voltage 587 vac 587 vac 587 vac 587 vac 577 vac 577 vac 577 vac 587 vac

Inertia (lbft2) 429 429 429 429 767 767 767 524

Approximate Weight (lbs) 6500 6500 6500 6000 8500 8500 7878 7600

20185-A

Experience and ReliabilityAC and DC Drilling Motor Solutions for the Future

AC motor offshore features: ATEX certification Ex II T3, II 2G c by Sira; spark-less heavy-duty blower assembly; blower motor rated for hazardous locations; 6-pole stator with form-wound windings; Class H insulation with superior GE VPI process; 100-ohm platinum RTDs embedded in the stator windings; insulated bearing on the non-drive end of the motor; pressure sensor; space heater; IP44 louvered air intake panels; stainless steel IP56 connection box, IP44 motor rating.

AC motor land features: Motor not available with ABS or ATEX certification. Includes hood style blower air intake, painted carbon steel connection box and IP23 motor rating.

*DNV certification available as an option ** ATEX certification Ex de II T4 Gb IP56, de II 2G c by Sira

Now available with ATEX certification Ex px de IIC T3 II 2G by Baseefa; blower motors rated for hazardous locations; pressurized connection box with double bolt-on cable connection; pressure sensor to verify ventilation; sparkless 10hp heavy-duty blower; intake hood that protects against blowing rain, Class H insulation; auxiliary lockout switch; space heater; optional marine features (ABS-certified shaft; armored cables; two 100-ohm platinum RTDs).

Visit us online at gedrillingpower.com