Automotech Services Ltd€¦ · Services Ltd EST 1972 Specialists in vehicle lifts and garage equipment Issue 02-16. Two Post Lifts Automotech was established in 1972 Call now: 01889

Call now: 01889 579945www.automotechservices.co.uk

Automotech Services Ltd

EST 1972

Specialists in vehicle lifts and garage equipment

Issue 02-16

Two Post Lifts

Automotech was established in 1972 Call now: 01889 579945


AS-235SB Twin HydraulicRam, 2 Post LiftThis two post lift uses a twin hydraulic ram design for steady raising and lowering operation. This sturdy proven lift will give you trouble free service for many years.

Features• Lifting capacity 3.5T• Lifting height 1900mm • Minimum height 110mm• Manual safety locks in each post• Lift pad extensions optional• Single or 3 phase option

£999+ VAT

ONLY

DELIVERYFROM ASLITTLEAS £50

3.5TLIFTING

TELESCOPIC ARMS

800mm-1200mm 800mm-1200mm

110mm

210mm

Dimensions

Our lifts are fitted with a low voltage control system

Automatic arm locks


AS-6140A Twin HydraulicRam, 2 Post LiftThis lift is simple and robust. Uses a twin hydraulic ram design for steady raising and lowering operation. Although 4T capacity you can still lift the smallest cars with this machine.

Features• Lifting capacity 4T• Lifting height 1900mm• Minimum height 98mm• Manual safety locks in each post• Lift pad extensions included (for vans / 4X4)• Single or 3 phase option

£1,199+ VAT

ONLY


All our new equipment comes with 12 months’ warranty as standard

Automatic arm locks

50mm low clearance base plate

Dimensions

Now with 2 and 3 stage telescopic arms

980mm - 1420mm

740mm - 1310mm

50mmextension

75mmextension

150mmextension

Extra lifting pad for long arms

Lift pad extensions for vans / 4x4 included

4TLIFTING

800mm-1200mm

Two Post Lifts




AS-6240TA Twin HydraulicRam, Clear Floor, 2 Post LiftThis lift is simple and robust. Uses a twin hydraulic ram design for steady raising and lowering operation. Although 4T capacity you can still lift the smallest cars with this machine.

Features• Lifting capacity 4T• Lifting height 1900mm• Minimum height 98mm• Manual safety locks in each post• Safety shut-off bar on the overhead bridge• Lift pad extensions included (for vans / 4X4)• Single or 3 phase option

ONLY

£1,299+ VAT

Dimensions4TLIFTING


50mmextension

75mmextension

150mmextension

Lift pad extensions for vans / 4x4 included


Specialists in vehicle lifts and garage equipment Call now: 01889 579945www.automotechservices.co.uk



£1,950+ VAT

ONLY

AS-6246/H1 Twin Hydraulic Ram Clear Floor 2 Post LiftThis lift uses direct drive hydraulic rams and a single point safety lock release system. This means there are very few moving parts and components. The double “S” bent post structure increases the post strength making the lift very strong and stable. Although 4T capacity the smallest and lowest cars can still be lifted using this machine, with the lift pad lowest height at just 85mm.

Features• Lifting capacity 4T• Lifting height 1800mm• Minimum height 85mm• Single point manual safety locks• Double screw pad adapters• Asymmetrical or Symmetrical configuration• Safety shut off bar on the overhead bridge• Lift pad extensions included (for vans / 4X4)• Single phase or 3 phase option

C.E. APPROVED LOCKS

Our automatic arm locks are fully approved, tested and safe. Automatically disengage when the lift is lowered

24V at the buttons


170mm 100mm 25mm

80mm lift pad extensions + holder included

4162

4020

85-1

50

890-1470 890-1470

600-1100 600-1100

2850

1800

1794

3436

Dimensions for symmetrical configuration

4TLIFTING

ASYMMETRICAL

SYMMETRICAL

Can be installed in asymmetrical or symmetrical configuration

Two Post Lifts

£2,050 + VAT

ONLY

AS-6150A Twin Hydraulic Ram, 2 Post LiftThis lift is ideal for lifting large vans and commercial vehicles, with its huge lifting capacity of 5000Kg. The design of the arms will also allow the machine to be used on cars.

Features• Lifting capacity 5T• Lift height 1900mm• Minimum height 120mm• 3 stage lifting arms• Safety locks in each post• Lift pad extensions included• 240v single phase or 415v 3 phase


Specialists in vehicle lifts and garage equipmentInstallation service available Please contact us for information

860mm - 1800mm 860mm - 1800mm Dimensions

C.E. approved locks automatically disengage when lift is lowered

50mmextension

80mmextension

180mmextension

5TLIFTING

Lift pad extensions included



AS-6350A 5T Twin Hydraulic Ram Clear Floor 2 Post LiftThis lift is ideal for lifting large vans and commercial vehicles where a clear floor is required. The lifting capacity of 5000Kg and arms which will extend to 1800mm makes this two post lift very stable when lifting long wheel base vans. The unique design of the arms will also allow the machine to be used on cars as the lift pad minimum height is only 120mm.

Features• Lifting capacity 5000Kg• Lift height 1900mm• Minimum height 120mm• 3 stage lifting arms• Safety locks in each post• Lift pad extensions included• 240v single phase or 415v 3 phase• Floor Bolts Included• Fully C.E. approved• Low voltage control system (as required by regulations)

£2,199 + VAT

ONLY

Dimensions

180mm extension

80mm extension

Includes 2 sets of lift pad extensions

50mm extension

80mm extension

180mm extension

C.E. approved locks automatically disengage when lift is lowered

5TLIFTING

24V CONTROLS Our lifts are fitted with a low voltage control system as standard


POST HEIGHT OPTIONS4300mm 4600mm

4800mm5100mm

Model AS-6350A/H

Model AS-6350A/H1

860mm

Single Post Lifts



AS-7251 Single Post Vehicle liftThis lift is designed for workshops where space is at a premium. It is totally mobile and can be moved by one person with ease once unloaded. The lift has the added advantage over other mobile vehicle lifts in that it will lift to a full working height like any conventional two post vehicle lift.

Features• Lifting capacity 2.5T• Lifting Height 1755mm• Fully Mobile (When unloaded)• Four Extendable Swivel Lifting Arms• Double Screw Adjustable Lift Pads• 12 piece Lift Pad Adaptor Kit Included (For vans / 4×4)

£1,800 + VAT

ONLY

150mm

100mm

50mm

Lift pad adaptor kit included

2.5TLIFTING

Dimensions



AS-7251B Single Post Vehicle liftThis liftis designed for workshops where space is at a premium. This lift takes up very little space and can be installed where there is no room for a conventional vehicle lift. The four swivel lifting arms are easily adjusted, they will lock automatically and stay in place during operation.

Features• Lifting capacity 2.5T• Lifting Height 1755mm• Four Extendable Swivel Lifting Arms• Double Screw Adjustable Lift Pads• 12 piece Lift Pad Adaptor Kit Included • (For vans / 4×4)• Floor Bolts Included

2.5TLIFTING

Dimensions

150mm

100mm

50mm

Lift pad adaptor kit included

£1,650 + VAT

ONLY


Four Post Lifts



AS-4T36S Mobile 4 Post Parking LiftThis lift has a bed length of just 3200mm. This makes this four post lift ideal for vehicle storage when space is at a premium. The lift can be moved within minutes with the aid of the mobile wheel kit provided. The perfect lift for Classic car restoration enthusiasts as the lift can also be used as a conventional 4 post lift for servicing.

Features• Lifting capacity 3.6T• Lifting height 1900mm• Platform length 3200mm• Full Mobile Wheel Kit Included• 3pcs Oil Drip Trays Included• 1pcs Jack Tray Included

£1,620 + VAT

ONLY

Dimensions

3.6TLIFTING

Full mobile wheel kit included Dual safety locks at each post

Robust mechanical safety lock system

820mm

Maximum height 360mm

Extendable to 1130mm

2.5T jacking beam

OPTIONAL JACKING BEAM




AS-4T36 Mobile 4 Post Parking LiftThis lift is the ideal lift for vehicle storage when space is tight. The lift can be moved within minutes with the aid of the mobile wheel kit provided. The perfect lift for Classic car restoration enthusiasts as the lift can also be used as a conventional 4 post lift.

Features• Lifting capacity 3.6T• Lifting height 1900mm• Platform length 4000mm• Full Mobile Wheel Kit Included• 3pcs Oil Drip Trays Included• 1pcs Jack Tray Included

£1,520 + VAT

ONLY

Dimensions

Robust mechanical safety lock system

3.6TLIFTING

Dual safety locks at each post

820mm

Maximum height 360mm

Extendable to 1130mm

2.5T jacking beam


Full mobile wheel kit included

Three piece oil drip tray and jack tray included


Four Post Lifts



AS-6745P 4.2T 4 Post Vehicle LiftThis lift is capable of lifting vehicles up to 4200Kg. The lift platform has a low profile of 130mm from the ground and is fitted with 970mm long drive on ramps. This means the lift can handle low riding cars as well as light commercial vehicles.The AS-6745P has a 2500Kg rolling jacking beam fitted as standard to give a wheel free operation. The platform length of 4800mm makes this lift a great all-round machine.

Features• 4200 Kg capacity• 2500Kg Jacking Beam included (with rubber lifting blocks and extensions)• Extra-long drive up ramps• Mechanically operated safety locks• Hydraulic failure safety devices• Mechanical failure safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

£2,350 + VAT

ONLY

4.2TLIFTING

766mm

4

28m

m

1626mm

2500Kg Jacking beam included

REV. 01 2014 10 / 32

Figure 3a – LIFT LAYOUT - STANDARD TYPE

Figure 3b – LIFT LAYOUT – ALIGNMENT TYPE

Dimensions






AS-6745 4.2T 4 Post Alignment Vehicle LiftThis 4 post lift is designed for vehicle wheel alignment adjustment and the servicing of vehicles. The AS-6745 Is capable of lifting vehicles up to 4200Kg. The machine is fitted with front removable turn plates and multi-directional lockable rear slip plates on to the 4800mm long lift bed. When the lift is operated for service work the front turn plate recesses can be covered giving the lift platform a uniform flat working area. The lift is fitted with 970mm long drive on ramps, this means the lift can handle low riding cars as well as light commercial vehicles. The AS-6745 has a 2500Kg rolling jacking beam fitted as standard to give a wheel free operation.

Features• 4200 Kg capacity• 2500Kg Jacking Beam included • (with rubber lifting blocks)• Front turn plates included• Rear slip plates• Extra-long drive up ramps• Mechanical operated safety locks• Hydraulic failure safety devices• Mechanical failure safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

£2,650 + VAT

ONLY

400mm

300mm 400mm

45mmTURN PLATES INCLUDED

Dimensions

REV. 01 2014 10 / 32

Figure 3a – LIFT LAYOUT - STANDARD TYPE

Figure 3b – LIFT LAYOUT – ALIGNMENT TYPE


766mm

4

28m

m

1626mm



4.2TLIFTING

Four Post Lifts



AS-6764P 6.4T Four Post LiftThis four post lift has the added advantage of being capable of lifting up to 6.4T without compromising its capabilities for lifting normal passenger cars. With its extra-long drive on ramps and 178mm low level lifting bed it is capable to load low riding vehicles with ease. The lift has a bed length of 5216mm to accommodate long wheel base and light commercial vehicles.

Features• Lifting capacity 6.4T• 3200Kg Jacking Beam included (with rubber lifting blocks)• Extra-long drive up ramps• Mechanical Air operated safety locks• Hydraulic failure safety devices• Mechanical failure safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

ONLY

£3,899 VAT

Dimensions

915mm

1473mm

1800mm



6.4TLIFTING





AS-6764 6.4T Four Post Alignment Vehicle LiftThis alignment 4 post lift is designed for vehicle wheel alignment adjustment and the servicing of vehicles. The machine is fitted with front removable turn plates and multi-directional lockable rear slip plates on to the 5216mm long lift bed. The lift has the added advantage of being capable of lifting up to 6.4T without compromising its capabilities for lifting normal passenger cars. When the lift is operated for service work the front turn plate recesses can be covered giving the lift platform a uniform flat working area.

Features• Lifting capacity 6.4T• 3200Kg Jacking Beam included (with rubber lifting blocks)• Extra-long drive up ramps• Mechanical Air operated safety locks• Hydraulic failure safety devices• Mechanical failure safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

£4,277 + VAT

ONLY

Dimensions

915mm

1473mm

1800mm



Turn plates included

6.4TLIFTING

3200kg jacking beam included

Scissor Lifts



AS-8240TP 4T Capacity Scissor Lift This machine has all the advantages of a 4 post lift without the restrictions of the posts taking up valuable workshop space. The scissor lift can be surface mounted or flush fitted. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles.

Features• Lifting capacity 4T• 2500Kg Jacking Beam included (includes lift pad extensions)• Can be surface mounted or flush mounted• Extra-long drive up ramps• Hydraulic failure safety devices• Mechanical air operated safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

ONLY

£4,060 VAT

Dimensions for on-ground installation

4TLIFTING

180mm

80mm

Optional flush mount drive on ramps, for infloor installation


Jacking beam lift pad extensions included




AS-8240TX 4T Alignment Scissor LiftThis machine is designed for wheel alignment and the servicing of vehicles. The machine is fitted with lockable rear slip plates and front turn plates as standard for wheel alignment operation. The front turn plate covers can be fitted when the turn plate operation is not required. Also fitted as standard is the 2500Kg rolling jacking beam with screw pad adapters to accommodate all vehicles. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles.

Features• Lifting capacity 4T• Lifting height 2160mm• Minimum height 290mm• Can be surface mounted or flush mounted• Front turn plates included• Turn plate covers included• Extra long rear slip plates• Extra long drive up ramps• Hydraulic failure safety devices• Mechanical safety locks• Low voltage control system (as required by regulations)

ONLY

£4,200+ VAT

180mm

80mm




Air operated Safety locks

4TLIFTING





Scissor Lifts



AS-8240T 4T Alignment Scissor LiftThis alignment scissor lift is manufactured to the highest standards, giving the perfect solution for wheel alignment operations and the servicing of vehicles. The alignment scissor lift has the added advantage of having the built in secondary, wheel free scissor lift. The lift can be surface mounted or flush mounted. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles. The vehicle lift comes fitted with rear slip plates at a length of 1563mm making the machine able to accommodate small cars and light commercial vehicles for wheel alignment operations.

Features• Lifting capacity 4T• 4T Capacity secondary wheel free scissor lift• 2500Kg Jacking Beam included (includes lift pad extensions)• Can be surface mounted or flush mounted• Front turn plates included• Turn plate covers included• Rear slip plates• Extra-long drive up ramps• Hydraulic failure safety devices• Mechanical safety locks

ONLY

£4,620+ VAT


180mm

80mm


4TLIFTING



Installation service available Please contact us for information



Our lifts are fitted with a low voltage control system 400mm

400mm

45mm

Turn plates included Removable front turn plate covers

Rear multi-directional slip plates

Built in, wheel free scissor lift

Front turn plates with covers

4420mm

1

308c

m

290mm -2160mm

300mm

Scissor Lifts



AS-8250P 5T Alignment Scissor LiftThis machine has all the advantages of a 4 post lift without the restrictions of the posts taking up valuable workshop space. This scissor lift can be surface mounted or flush fitted. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles. The lift platforms are fabricated from high quality plasma cut steel giving a uniform flat working area. The lift is also supplied with the 2500Kg Air / hydraulic rolling jacking beam with screw pad adapters to accommodate all vehicles.

Features• Lifting capacity 5T• 2500Kg Jacking Beam included (includes lift pad extensions)• Can be surface mounted or flush mounted• Extra-long drive up ramps• Hydraulic failure safety devices• Mechanical air operated safety locks• Floor bolts included• Fully C.E. approved• Low voltage control system (as required by regulations)

ONLY

£4,280+ VAT





180mm

80mm


5TLIFTING



AS-8250N 5T Alignment Scissor LiftThis machine is designed for wheel alignment and the servicing of vehicles. The machine is fitted with lockable rear slip plates and front turn plates as standard for wheel alignment operation. The front turn plate covers can be fitted when the turn plate operation is not required. Also fitted as standard is the 2500Kg rolling jacking beam with screw pad adapters to accommodate all vehicles. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles.

Features• Lifting capacity 5T• Lifting height 2160mm• Minimum height 290mm• Can be surface mounted or flush mounted• Front turn plates included• Turn plate covers included• Extra long rear slip plates• Extra long drive up ramps• Hydraulic failure safety devices• Mechanical safety locks• Low voltage control system (as required by regulations)

ONLY

£4,600+ VAT


5TLIFTING

180mm

80mm






Scissor Lifts



AS-8250A1 5T Alignment Scissor LiftThe perfect solution for wheel alignment operations and the servicing of vehicles. This alignment scissor lift has the added advantage of having the built in secondary, wheel free scissor lift. The lift can be surface mounted or flush mounted. When installed on the surface the extra-long drive up ramps will accommodate low riding vehicles.

Features• Lifting capacity 5T• 4000 Kg Capacity secondary wheel free scissor lift• 2500Kg Jacking Beam included (includes lift pad extensions)• Can be surface mounted or flush mounted• Front turn plates included• Turn plate covers included• Rear slip plates• Extra-long drive up ramps• Hydraulic failure safety devices• Mechanical safety locks• Floor bolts included• Fully C.E. approved

ONLY

£5,200+ VAT

5TLIFTING



180mm

80mm






Our lifts are fitted with a low voltage control system 400mm

300mm 400mm

45mm


Built-in secondary scissor lift for wheel free operation

Removable front turn plate covers

Air operated safety locks

1308cm

5000mm

Scissor Lifts



AS-7430H 3T Low Entry FullRise Scissor LiftThe AS-7430H Full height scissor lift uses a single scissor action to gain full working height. This makes the lift very stable during raising and lowering operations. The AS-7430H also has the added advantage over other surface mounted scissor lifts in that it is mounted within its own frame. This allows the extra-long drive up ramps, built into the machine to accommodate low riding vehicles. With the built in lifting blocks and end positioning stop this machine is quick to load and operate.

Features• 3000Kg capacity• Extendable Lift Platforms• Rubber Lift blocks Included• Low voltage control system• Low maintenance due to hydraulic design• Safety lock in each platform + Hydraulic anti surge valve.• Floor Bolts Included• Fully C.E. approved• Low voltage control system (as required by regulations)

ONLY

£2,095+ VAT

Dimensions

24V CONTROLSOur lifts are fitted with a low voltage control system, as is required. Powerful hydraulic unit single or 3 phase option

Quick and easy to load vehicles onto the lift

End stops makes positioning the vehicle quick and easy

Lift platforms can be extended to accommodate longer vehicles

Extends + 446mm

Installation service available Please contact us for information



Long drive on ramps to accommodate low vehicles

1073mm

Rubber lift pads mounted to platform

Air operated mechanical safety locks

Twin hydraulic synchronised rams in each platform gives a clear and safe working area between the lift

3TLIFTING

Scissor Lifts



AS-7135 3.5T Full Rise Scissor LiftThis 3.5T capacity low profile scissor lift is surface mounted, there is no need for expensive ground works. An ideal machine when space is tight and full working height is required.

Features• Lifting capacity 3.5T• Lifting height 1900mm• Minimum height 115mm• Extendable lift platforms• Hydraulic failure safety devices• Low voltage control system• Rubber lift blocks included

£2,250+ VAT

ONLY

Drive up ramps can be locked in the upright position to extend the platform length Quick release lock

Twin hydraulicallysynchronised rams in each platform means a clear and safe working area between the lift

Dimensions

X4 rubber sill mounting blocksincluded

3.5TLIFTING





AS-7230A Scissor Lift

This low profile full rise scissor lift is surface mounted, there is no need for expensive ground works. An ideal unit when space is tight.

Features• Lifting capacity 3T• Lifting height 1900mm• Minimum height 112mm• Rubber lift blocks included• Single or 3 phase option

£1,799+ VAT

ONLY

REV. 01 11 / 29

Figure 2 – LAYOUT

REV. 01 11 / 29

Figure 2 – LAYOUT

Dimensions

3TLIFTING

Machine bolts directly to the floor. No need for expensive ground works


Drive up ramps can be locked in the upright position to extend the platform length


Scissor Lifts



Full height witha clear working

area between platforms

3TLIFTING

Lift platforms can be extended for longer vehicles

AS-7330 Three Tonne Scissor LiftIn floor, full rise scissor lift gives a flush floor finish when lowered. This means that the minimum height is 0mm. The installed lift gives a very professional appearance to any workshop.

Features• Lift capacity 3T• Lift height 1700mm• Minimum height 0mm• Rubber lift blocks included• Pneumatic safety locks• 240v single phase or 415v 3 phase

£1,799+ VAT

ONLY

REV. 02 10 / 30

Figure 2 - LAYOUT

Drive on

Dimensions






AS-7532B 3.2T Mid Rise Scissor LiftA surface mounted low profile mid-rise scissor lift with a minimum height of just 110mm. Its unique design gives a clear working area between platforms. An ideal lift for busy repair shops and tyre bays.

Features• Lifting capacity 3.2T• Lifting height 1000mm• Minimum height 110mm• Extendable lift platforms• Hydraulic failure safety devices• Low voltage control system• Rubber lift blocks included

£1,599+ VAT

ONLY

1460mm -1994mm

860mm

490mm

110mm

Dimensions

3.2TLIFTING



Twin hydraulically synchronised rams in each platform means a clear and safe working area between the lift

Drive up ramps can be locked in the upright position to extend the platform length Quick release lock

Scissor Lifts



AS-7530D Mobile Scissor LiftThis scissor lift is ideal for tyre shops / body shops, with the advantage of it being totally mobile.

Features• Fully mobile• Lifting capacity 3T• Extendable platform• Lifting height 1000mm• Minimum height 110mm• Pneumatic safety locks• 240V single phase• No installation required

£1,299+ VAT

ONLY


Dimensions

REV. 01 2012 10 / 26

Figure 2 - LAYOUT

Mobile Wheel Kit Every machine comes with a full mobile kit as standard

3TLIFTING

X4 rubber sill mounting blocks included

860mm

490mm

110mm

1420mm - 1990mm

Drive up ramps can be locked in the upright position to extend the platform length

Quick release lock





1420mm - 1990mm £995 + VAT

ONLY

AS-7630 Mobile Scissor lift

This compact mobile scissor lift is ideal for tyre and body shops. A great favorite with DIY and classic car enthusiasts.

Features• Lifting capacity 2.7T• Lifting height 1300mm• Minimum height 118mm• 240v single phase• No installation required• No air supply required

50mmextension

100mmextension

150mmextension

200mmextension

Lift pad extensions as standard

2.7TLIFTING

Our lifts are fitted with a low voltage control system Fully adjustable arms

Fully mobile

Electro / mechanical safety lock

Dimensions

Scissor Lifts




£780 + VAT

ONLY

AS-5500 2.5 Tonne Scissor Lift The AS-5500 mobile lift has no electrical connection as it is operated with a powerful air / hydraulic pump. A great favorite with DIY and classic car enthusiasts.

Features• Lifting capacity 2.5T• Lift height 1025mm• Minimum height 123mm• Pneumatic safety locks• Air operated (compressor required 6-7 bar)

1025mm max

2.5TLIFTING

Air operated! No electrical supply required

1015mm

293mm

123mmMIN

2554mm

The lift is supplied with a mobile kit as standard

Mobile LiftSpecialists in vehicle lifts and garage equipment We offer innovative leasing options


£300+ VAT

ONLY

AS-0901/1 Portable Tilting Lift

This mobile lift is ideal for any workshop, mobile mechanic or DIY enthusiast. Lightweight and very portable, no need for any air or power supply.

Features• Lifting capacity 1.5T• Lightweight design 58Kg • Vehicle can be tilted forwards or backwards • Supplied with manual handle • Supplied with bracket so that a drill can be used to raise and lower • Lift can be locked at required angle • Lifting height 585mm • Min height 150mm 1550

1185

1530

800

585

1285

150

Dimensions

Mobile Lift



Dimensions

Includes four quick fit adaptors to lift via wheel or car body

Fitted with air/hydraulic pump

Mechanical safety device

AS-1500SL 1.5T Mobile Side LiftThis mobile lift is powered by an air operated hydraulic pump and can be easily controlled to raise or lower the vehicle. The perfect machine for mechanical repairs, bodywork and so much more.

Features• 1.5T capacity (For max vehicle weight 2500kg)• High quality Air / Hydraulic pump. (No electrical connection required).• Includes Four quick fit lifting adapters• Very versatile and easy to move• Hydraulic failure safety devices• Mechanical safety device• Fully C.E. approved

£560+ VAT

ONLY




AS-7607 Motorcycle Scissor LiftThis high quality motocycle lift is the ideal solution for motorcycle servicing and repairs. Its optional side platforms can be added to turn this versatile lift into a quad bike or mini tractor lift.

Features• Retractable drive up ramp• Removable rear platform section• Front wheel clamp• Tool tray• Bike tie down brackets• Air operated (compressor required 6-7 bar)• Optional 240V hydraulic version

£795+ VAT

ONLY

Air operated! No electrical supply required

Optional 240v hydraulic version

Fitted with optional platform

Dimensions

Slide away drive on ramp


Tyre Machines



SPACE SAVING

VEHICLE LIFTS


£490+VAT

ONLY

AS-20SA SEMI AUTOMATIC TYRE CHANGERThis compact machine is simple to use, with a turntable that will clamp up to 20”rims.

Features• Swing arm / semi automatic style• 10” - 20” rim clamping• Inflation gauge included• Tyre lever included• 240v single phase

£580 +VAT

ONLY

AS-24SASEMI AUTOMATIC TYRE CHANGERThis Semi automatic machine is compact, simple to use and will handle rims up to 24”. A great value for money machine.

Features• Swing arm / Semi- Automatic style• 10”- 24” Rim clamping• Inflation gauge included• Tyre lever included• Plastic jaw protectors included• 240v Single phase• Motorcycle adapters available Cost £80

Includes aluminium wheel protection kit / tyre lever and inflation gauge



ONLY

£800 +VAT

ONLY

AS-24FAFULLY-AUTOMATIC TYRE CHANGERThis Automatic machine is a tilting back arm design, with a built in jaw bead blaster for seating tyre’s quickly.

Features• Fully-Automatic style• 12”- 24” Rim clamping• Built-in inflation gauge included• Tyre lever included• Plastic jaw protectors included• 240v Single phase• Motorcycle adapters available Cost £80

Includes aluminium wheel protection kit / Tyre lever / Tyre pressing tool

£1,199 +VAT

ONLY

AS-24XFA AUTOMATIC - TYRE CHANGER WITH POWER ASSIST ARMThe automatic machine is the same as the AS-24FA but with the addition of a powerful pneumatic assist arm. The air operated bead lifting and pressing device makes tyre mounting and demounting much easier, especially stiff beaded low profile tyres.

Features• Fully Automatic style• Air operated assist arm• 12”- 24” Rim clamping• Built-in inflation gauge included• Built-in jaw bead blaster• Plastic jaw protectors included• 240v Single phase• Motorcycle adapters available Cost £80

Includes aluminium wheel protection kit / Tyre lever / Tyre pressing tool


Tyre Machines



£895 +VAT

ONLY

AS-28XSA SEMI AUTOMATIC TYRE CHANGER WITH TWIN ASSIST ARMSCapable of handling rims up to 28” the twin air operated bead lifting and pressing rams make tyre mounting and demounting much easier.

Features• Swing arm/semi automatic • Style with twin assist arms • Inflation gauge • Plastic jaw protection covers • Tyre lever • Water/oil separators • Single phase 240v supply • Motor power 0.75 - 1.1Kw • Max wheel diameter 1143mm/45” • Inner clamping 14” - 28” • Outer clamping 12” - 25” • Bead break force 2500Kg • Net weight 200Kg • 12 month parts warranty • 240v plug in • Package size 1130 x 900 x 1030mm

£845+VAT

ONLY

AS-24XSA SEMI– AUTOMATIC TYRE CHANGER WITH TWIN ASSIST ARMS This compact machine has the advantage of having the twin air operated bead lifting and pressing rams fitted from above. This makes tyre mounting and demounting much easier.

Features• Swing arm / semi automatic• Twin assist arms• 12”-24” rim clamping• Inflation gauge included• Plastic jaw protection covers included• Tyre lever included• 240v single phase



ONLY

AS-401MOTORISED WHEEL BALANCER The AS-401A Automatic wheel balancer is capable of balancing wheels up to 26” in diameter. The wheel size is entered automatically making the data entry process very quick and simple. This machine is complete and ready to use and is supplied with a set of cones, measuring callipers and weights pliers.

Features• 10” - 26” rim diameter• 1.5” - 20” rim width• Auto spin once hood is lowered• Auto stop / positioning• Set of 4 cones included• Alloy wheel programs• Calipers, weight pliers included• Counter balanced chassis• 240v single phase

£650+VAT

ONLY

Easy to use, user friendly design. Selectable programs: Standard, Aluminium, Dynamic and Motorcycle

Included: Set of 4 cones, measuring callipers, quick release speed nut and weight pliers

£545 +VAT

ONLY

AS-B24MOTORISED WHEEL BALANCER The AS-B24 wheel balancer is capable of balancing wheels up to 24” in diameter. This is a user friendly machine and very simple to operate. The machine is complete and ready to use and is supplied with a set of four cones, measuring callipers and weights pliers.

Features• 10” - 24” rim diameter• 1.5” - 20” rim width• Auto spin once hood is lowered• Set of 4 cones included• Alloy wheel programs• Calipers, weight pliers included• 240v single phase

Easy to operate touch pad design. Standard, aluminium, dynamic and split weight functions

Included: Set of cones, measuring callipers, weight pliers and a Haweka quick release speed nut

We offer innovative leasing options

Wheel Balancers

Wheel Balancers



The ideal machine for the mobile tyre fitter

£375 +VAT

ONLY

AS-HW24BENCH MOUNTED HAND SPIN WHEEL BALANCER (12 VOLT DC)The AS-HW24 Hand spin wheel balancer is ultimate solution when space is at a premium. It can be bolted onto an existing workshop bench or into a vehicle. It is then used in the same manner as a floor mounted wheel balancer.

Features• Ideal for Mobile vans and workshops• Selectable programs, Standard, Aluminium, Static, Dynamic, Motorcycle• Easy to operate touch pad design• 12Vdc 1Amp (240Vac - 12Vdc adaptor + 12Vdc cigarette lighter adaptor supplied)• Callipers, weight pliers included• Set of 4 cones included• Quick release speed nut supplied.• 10”- 24” Rim diameters• 1.5”-20” Rim Width

£499 +VAT

ONLY

AS-HB24 HAND SPIN WHEEL BALANCER This floor mounted hand spin wheel balancer is ideal for a workshop or a van when space is tight. This user friendly machine is capable of balancing wheels up to 24” in diameter. The machine is complete and ready to use in minutes. It is supplied with a set of 4 cones, weight pliers and measuring callipers

Features• 10” - 24” rim diameter• 1.5” - 20” rim width• Set of 4 cones included• Alloy wheel programs• Calipers, weight pliers included• 240v single phase

Included: Set of cones, measuring callipers, weight pliers and a Haweka quick release speed nut

Easy to operate touch pad design. Standard, aluminium, dynamic and split weight functions

Tyre Machine AccessoriesSpecialists in vehicle lifts and garage equipment We offer innovative leasing options


AS-401CLAThe adapter enables centre less wheels (Wheels manufactured without a hole in the centre) to be mounted to the AS-401 Balancer.

£185 +VAT

ONLY

AS-401LCThe large cone adapter enables the AS-401 balancer to handle wheels with a larger than 140mm centre hole.

£ 110 +VAT

ONLY

AS-401MCAThe adapter enables the AS-401 Balancer to balance motorcycle wheels.

£ 140+VAT

ONLY

AS-B24LCThe large cone adapter enables the AS-B24 range of balancers to handle wheels with a larger than 140mm centre hole.

£ 70 +VAT

ONLY

AS-B24CLAThe adapter enables centre less wheels (Wheels manufactured without a hole in the centre) to be mounted to the AS-B24 range of balancers.

£ 140+VAT

ONLY

AS-B24MCAThe adapter enables the AS-B24 range of balancers to balance motorcycle wheels.

£ 120 +VAT

ONLY

AS-24MCJ The kit enables motorcycle wheels to be mounted on to all Automotech 24” and above tyre machines.

£ 80 +VAT

ONLY

AS-18AB BEAD SEATER The ideal tool for fitting / seating tyres to rims.

£ 118 +VAT

ONLY

AS-18ABHBEAD SEATER The ideal tool for fitting / seating tyres to rims, with easy operation via the slide valve on the hose.

£ 118 +VAT

ONLYONLY

Garage Equipment



AS-TU40These fully ball-raced cast iron turn plates will not bend or buckle under load. Ideal for use with Wheel Alignment / Tracking Gauges or MOT 4 Post Lifts.

Features• Plates come as a pair• Cast iron upper and lower components• Ball bearings fitted for ease of use and precision• Lock off feature (plates can be lock to stop rotation)• Tough powder coat paint finnish

ONLY

£230+VAT

AS-LWA50 Wheel Alignment GaugeThe AS-LWA50 wheel alignment gauge measures the angle between the vehicle wheels to give toe-in / toe-out readings. The unit is easily calibrated and very simple to use.

Features• Precision laser to indicate toe-in / toe-out• Can be used on vehicle lifts• Will work on vehicles with rim diameters 8”-24”• Battery powered by 2x AA batteries (included)• Laser beam height 40mm from floor• Measuring range +/-2deg• Laser class II

ONLY

£266.67+VAT

AS-LWA40 Wheel Alignment GaugeThe AS-LWA40 wheel alignment gauge measures the angle between the vehicle wheels to give toe-in / toe-out readings. The unit is easily calibrated and very simple to use.

Features• Precision laser to indicate toe-in / toe-out• Tough 2.5mm steel construction• Can be used on vehicle lifts• Will work on vehicles with rim diameters 6” - 23”• Battery powered by 2 x AA batteries (included)• Measuring range +/- 3deg• Laser class II

ONLY

£180+VAT

Garage EquipmentSpecialists in vehicle lifts and garage equipment


AS-0601-1 Engine / Gear Box StandThe ideal work station when rebuilding units.

Features• Capacity 350Kg• Fully adjustable cradle to accept a wide varity of engines / gearboxes• Head rotates 360 degrees• Steel casters

ONLY

£32+VAT

AS-0301C 1 Tonne Spring CompressorMakes changing shock absorbers quick and easy.

Features• 1T capacity (1000Kg)• For use on spring length 150mm - 500mm• For use on spring diameter 100mm - 175mm• Ram travel 325mm• High speed foot pump

ONLY

£104+VAT

AS-08027A 1 Tonne Spring CompressorMakes changing shock absorbers quick and easy.

Features• 1T capacity (1000Kg)• For use on spring length 150mm - 530mm• For use on spring diameter 100mm - 175mm• Ram travel 325mm• High speed foot pump• Two sets of quick change yokes

ONLY

£120+VAT

AS-0601-2 Engine / Gear Box StandThe ideal work station when rebuilding units.

Features• Capacity 450Kg• Fully adjustable cradle to accept a wide varity of engines / gearboxes• Head rotates 360 degrees• Steel casters

ONLY

£50+VAT

AS-0104-2 Engine Support BeamThe AS-0104-2 Engine support Beam is the essential tool when removing gear boxes / engine supports etc.

Features• Capacity 500Kg• Fully adjustable width 630mm - 1800mm• Fully adjustable support bracket (left, right, up, down)• Rubber mounted feet

£54.17ONLY

+VAT

AS-0901-2 Mini Motorcycle LiftThe lift is made from a solid steel construction with a durable powder coat finish. It can be placed quickly under the frame or engine of the motorcycle.

Features• Includes rubber-coated fully adjustable cradles• 0.5T Capacity (500Kg)• Dimensions (L X W X H) 450mm x 150mm x 90mm• Min Height 90mm (Without cradles)• Max Height 500mm ( With Cradles)• Weight 14.5Kg

£49.99ONLY

+VAT


Garage Equipment



AS-0901F 20T Floor Mounted PressFeatures• 20T hydraulic pump• Floor mounted• Movable / lockable. Direct push ram (not bottle jack type)• Ram stroke 145mm

£180ONLY

+VAT

AS-3004A 20T Floor Mounted PressFeatures• 20T capacity 9 piece quick change pressing tool kit included. 10, 12, 16, 18, 20, 22, 25, 30mm• Pressing plates included• Two speed hydraulic pump• Movable direct push ram. (Ram moves with ease on roller bearings)• High quality powder coating• Multi position bed 0mm - 1030mm• Bed working width 440mm

£245ONLY

+VAT

AS-03019 30T TWO STAGE HYDRAULIC FLOOR MOUNTED PRESSThis press is fully adjustable and uses roller bearings for easy lateral movement of the direct push ram. The two stage hydraulic pump unit gives speed and precision during operation.

Features• 30T capacity• Foot or hand operated• Two stage hydraulic pump• Welded main structure• Reversible pressing plates / V blocks included• Movable direct push ram. (Ram moves with ease on roller bearings)• High quality powder coating• Multi position bed 0mm - 1010mm• Bed working width 535mm

£410+VAT

ONLY

Garage EquipmentSpecialists in vehicle lifts and garage equipment



AS-0601B 2.0 Tonne Folding Engine CraneFeatures• Lift capacity 2.0T• Four lift positions 2000Kg, 1500Kg, 1000Kg, 500Kg• Maximum lift height to hook 2340mm• High speed hydraulic pump• Weight 80Kg

£110ONLY

+VAT

AS-1102B Hydraulic Pipe BenderSolid steel construction with durable powder coat finish.

Features• 16T Powerful Hydraulic Ram• Includes 8pc cast Iron formers. 1/2” 3/4” 1” 11/4” 11/2” 2” 21/2” 3” (15mm 20mm 25mm 32mm 40mm 50mm 65mm 80mm)

£104+VAT

ONLY

AS-0102A 0.6 Tonne Transmission JackA robust and useful piece of equipment for any workshop.

Features• Lift capacity 0.6T• Minimum height 1140 mm• Maximum height 1950mm

ONLY

£75.30+VAT

AS-0101H 0.5T 2 Stage Transmission JackThe jack has a lifting range from 820mm - 1740mm. With a fully adjustable cradle and tie down chains.

Features• 0.5T capacity• Fully adjustable cradle• Min height 820mm• Max height 1740mm• Steel casters• High speed hydraulic foot pump• Precision lowering valve

ONLY

£115+VAT

AS-0701D 2T High Position Jack StandFeatures• 2T capacity• 1250mm Minimum Height• 2130mm Maximum Height

ONLY

£62.83+VAT

Thread extension 135mm

AS-08039 Vehicle Positioning Jack

Features• 680Kg capacity (per jack)• Maximum tyre width 300mm• Maximum roller opening 530mm• Minimum roller opening 280mm• High speed hydraulic foot pump• Sold in pairs

£150+VAT

ONLY

Garage Equipment



AS-3812 Air Operated Portable Pneumatic JackFeatures• 2T capacity• Lightweight design at only 14Kg• Easy to use operating valve• Safety valve as standard• Minimum height: 115mm• Maximum lifting height: 295mm• Overall width: 250mm• Overall length 400mm• Lifting time 3 seconds• Operating pressure 145Psi / 10Bar

£162ONLY

+VAT

AS-3813 Air Operated Portable Pneumatic 3 Stage JackFeatures• 2T capacity• Lightweight design at only 16Kg• Easy to use operating valve• Safety valve as standard• Minimum height: 150mm• Maximum lifting height: 400mm• Overall width: 250mm• Overall Length 400mm• Lifting Time 3 seconds• Operating Pressure 145Psi / 10Bar

£182ONLY

+VAT

£182ONLY

+VAT

AS-1812 Air Operated Portable Pneumatic Trolley JackFeatures• 2T capacity• Lightweight design at only 16Kg• Easy to use operating valve• Safety valve as standard• Minimum height: 115mm• Maximum lifting height: 295mm• Overall width: 250mm• Overall length 1050mm• Lifting time 3 seconds• Operating pressure 145Psi / 10Bar

£192ONLY

+VAT

AS-1813 Air Operated Portable Pneumatic Trolley JackFeatures• 2T capacity• Lightweight design at only 16Kg• Easy to use operating valve• Safety valve as standard• Minimum height: 150mm• Maximum lifting height: 400mm• Overall width: 250mm• Overall length 1050mm• Lifting time 3 seconds• Operating pressure 145Psi / 10Bar

Max 295mm

Max 400mm




AS-80LPFeatures• Polyethylene 80L reservoir (you can see the oil clearly. The unit will not rust)• Rotary pump or gravity drain top• Adjustable height• Bowl diameter 440mm• Mobile with coasters

ONLY

£69.59+VAT

AS-36LFeatures• Polyethylene 36L reservoir (you can see the oil clearly. The unit will not rust)• Drain bowl with filter• Adjustable height• Max height 1600mm• Bowl diameter 440mm• Mobile with coasters

ONLY

£45.10+VAT

AS-200/300 Air Compressor 10.6cfm Features• 200L tank / receiver• 300L / min (10.6cfm) cast iron pump• 3Kw (4Hp)• Twin capacitor start• Slow running pump (less noise / less wear)• Oil lubricated • C.E. approved

£380ONLY

+VAT

AS-21/200 Air Compressor 6.7cfmFeatures• 21 litre tank / receiver• 192 l/ min (6.7cfm ) cast iron pump• (2hp) 240v (with plug)• Air outlet with regulator• Includes air hose and coupling• Oil lubricated for long life• Cast iron pump for long life

£80ONLY

+VAT

Prices effective from 1st May 2015. Prices and products are subject to change without notice. All prices exclude VAT and delivery

Automotech Services LtdTel: 01889 579945 Fax: 01889 579350 Email: [email protected]: www.automotechservices.co.uk

Unit 6, Oakhurst Park, The Levels, Brereton, Rugeley, Staffordshire, WS15 1RD

Vist the website

Documents

Automotech Services Ltd€¦ · Services Ltd EST 1972 Specialists in vehicle lifts and garage equipment Issue 02-16. Two Post Lifts Automotech was established in 1972 Call now: 01889