Upload
surfjuan-saaid
View
222
Download
0
Embed Size (px)
Citation preview
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 1/6
Automatic Identification System For Attendence
On this instructable I will try to show how to interface a RFID sensor with the Arduino. I am
using the RFID sensor from seeedstudio the serial version of it. There are a few parts you
will gonna need. I also bought some RFID keys.
UPDATE: Now it works with IDE 021
Step 1What you gonna need?
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 2/6
y
y
- Arduino Board
- RFID Sensor from seeedstudios
- Wires
- Protoboard
- RFID tags (125kHz) from seeedstudios
Step 2Plugging all together
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 3/6
y
y
y
Connect the antenna on the appropriate pins like the first photo.
Plug the RFID sensor to the protoboard like the second photo above.
Only 3 wires are required to interface, 2 wires for supply and another for the serial
line(communication)
The wires as connected as the third photo shows.
On RFID sensor: PIN 1 -> Tx
PIN 2 -> Rx (Not Used)
PIN 3 -> NC
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 4/6
PIN 4 -> GND
PIN 5 -> VCC (+5V)
Tx from RFID board goes to Digital PIN 2 on Arduino Board.
That is all you gonna need to wire.
Moving on to next step, the software.
Step 3The code I'm not a software guy, so this code is just for demonstration.
I don't make any kind of checksum at the tags code, but it seems to work fine.
The code is really simple. I used a new library for the serial, using software emulation.
With the two white cards you can deny or allow the access of others keys.
Any doubt, please ask me.
RFID_2_eng.pde1 KB
Step 4Results! There is no LED, sound or LCD for debug or visualization, just through the serial line.
The video demonstrate how to use the software. I didn't post any kind of explanation as text
on the video. I hope that the images spokes more then words, xD
Any doubt or suggestion, feel free to ask, or correct me.
Please, if you like it, rate it,
thank you
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 5/6
This RFID Reader Module (Serial version only) comes with two54x85mm Rectangle Tags.
Designed in cooperation with Grand Idea Studio, the Parallax Radio Frequency Identification (RFID) Reader Moduleis the first low-cost solution to read passive RFID transponder tags. The RFID Reader Module can be used in a widevariety of hobbyist and commercial applications, including access control, automatic identification, robotics,navigation, inventory tracking, payment systems, and car immobilization.
There are a variety of transponder tags that come in different packages. Each tag has a specific range that is within10% of the given distance for each type of tag. The reason for the 10% is due to environmental conditions and RFIDmodules.
Features:
Low-cost method for reading passive RFID EM4100 family transponder tags
2400 baud serial interface Enable input allows module to be enabled/disabled by software Bi-color LED for visual indication of status
Compatible tags:
54x85mm Rectangle Tag ISO Card: 6.3cm (2.5") +/- 10% 50mm Round Tag World Tag 50mm: 6.8cm (2.7") +/- 10% Blue Eye Key Fob
25mm Disk Tag
Key Specifications:
Reads 125 kHz Tags, EM41000 Family Power requirements: 4.5 to 5.5 VDC
Communication: Serial at 2400 baud (8N1) Dimensions: 2.45 x 6.25 x 0.22 in (62.2 x 82.5 x 5.57 mm)
Operating temp range: -40 to +185 °F (-40 to +85 °C)
8/3/2019 Automatic Identification System for Attendence
http://slidepdf.com/reader/full/automatic-identification-system-for-attendence 6/6