AUTOMATED ROLL-UP CURTAIN

Manual Part #: 39500142

Publication: AMEN00040 2020-07-06

ROLLTOP™

AUTOMATED ROLL-UP CURTAIN

2018-06-28 2018-06-28

2018-06-28

This Manual Covers Units Shipped After 1-1-2018, Refer to 1325F Units Prior.

This manual to remain with the unit:

Date Installed:_________________

2 Publication: AMEN00040 2020-07-06

SUPPORT POST INSTALLATION . . . . . . . . . . . . . . . .5

ROLLER TUBE INSTALLATION . . . . . . . . . . . . . . . . .6

FRONT TRACK INSTALLATION . . . . . . . . . . . . . . . . .7

DRIVE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . .8

ELECTRICAL INSTALLATION . . . . . . . . . . . . . . . . . .10

PHOTOEYE INSTALLATION . . . . . . . . . . . . . . . . . . .11

LIMIT SWITCH ADJUSTMENT . . . . . . . . . . . . . . . . .12

SHROUD / INTERLOCK INSTALLATION . . . . . . . . .13

MAINTENANCE / TROUBLESHOOTING . . . . . . . . .14

ELECTRICAL WIRING DIAGRAMS . . . . . . . . . . . . .15

SERVICE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . .18

ARCHITECTURAL DRAWINGS . . . . . . . . . . . . . . . .21

NOTICE TO USER

Our mission is to “Improve Industrial Safety, Security and

Productivity Worldwide Through Quality and Innovation.”

Thank you for purchasing the RollTop™ by RITE-HITE®

MACHINE GUARDING.

The RollTop™ automated roll-up curtain integrates

fabrics with technology to provide an effective safety

barrier against sparks, harmful light emissions and

physical contact with the machine by the operator.

RITE-HITE MACHINE GUARDING reserves the right to

modify the electrical and architectural drawings in this

manual as well as the actual parts used on this product

are subject to manufacturing changes and may be

different than shown in this manual. Due to unique

circumstances with varying requirements, may receive

separate prints with the unit.

Before returning any parts, you must contact the

Technical Support group to obtain authorization and a

PO#. Returned parts will not be accepted without a PO#.

If any procedures for the installation, operation or

maintenance of the RollTop unit have been left out of this

manual or are not understood, contact Technical Support

at 1-563-589-2722.

TOOLS & MATERIAL REQUIRED

Tube of Anti-Seize or Grease Lubricant

3/8in [10mm], 7/16in [11mm] 1/2in [13mm] & 9/16in

[14mm] Open End or Ratchet Wrench

3/8in [10mm], 7/16in, [11mm] 1/2in [13mm] & 9/16in

[14mm] Socket

Phillips Screwdriver

Straight Screwdriver (small 1/8in [3mm] blade)

Hammer

Hammer & Cordless Drill (3/8in [10mm] or 1/2in [13mm])

w/Phillips Bit

3/8in [10mm] or 1/2in [13mm] Masonry Bits

5/16” [8] Nut Driver

Tape Measure 25ft [8M] Minimum

Wire Strippers and Side Cutters

Retaining Ring Pliers

Set of Allen Wrenches

6ft [2M] Carpenters Level, Water Level

Multi-Meter

Straps For Lifting Roller Tube

Forklift

8ft [2.5M] or 10ft [3M] Step Ladder

Hardware for anchoring to the floor are not provided.

SPECIAL FEATURES

Unique design for special overhead crane applications.

Heavy-Duty, U.V. protected 50oz Armor Pleat curtain

fabric protects operator from intense light and flying

debris.

Fast, smooth opening operation.

Soft bottom edge

Interrupt switch capability

AMEN00040 2018-06-28

ROLLTOP™ MODEL 1325

PRODUCT INTRODUCTION

Publication: AMEN00040 2020-07-06 3

SAFETY WARNINGS


AMEN00040 2018-06-28

LOCKOUT/TAGOUT PROCEDURES

The Occupational Safety and Health Administration

requires that, in addition to posting safety warnings and

barricading the work area, the power supply has been

locked in the OFF position or disconnected. It is

mandatory that an approved lockout device is utilized. An

example of a lockout device is illustrated. The proper

lockout procedure requires that the person responsible

for the repairs is the only person who has the ability to

remove the lockout device.

In addition to the lockout device, it is also a requirement

to tag the power control in a manner that will clearly note

that repairs are under way and state who is responsible

for the lockout condition. Tagout devices have to be

constructed and printed so that exposure to weather

conditions or wet and damp locations will not cause the

tag to deteriorate or become unreadable.

RITE-HITE Corporation does not recommend any

particular lockout device, but recommends the utilization

of an OSHA approved device

(refer to OSHA regulation

1910.147). RITE-HITE

Corporation also recommends

the review and implementation

of an entire safety program for

the Control of Hazardous

Energy (Lockout/Tagout).

These regulations are

available through OSHA

publication 3120.

SAFETY IDENTIFICATION

NOTE:

A Note is used to inform you of important

installation, operation or maintenance information.

Danger indicates the presence of a hazard thatwill cause severe personal injury, death.

DANGER!

Warning indicates the presence of a hazard thatcan cause severe personal injury, death.

WARNING!

Caution indicates the presence of a hazard thatwill or can cause minor personal injury, death.

CAUTION!

Notice communicates installation, operation, ormaintenance information that is safety related

but not hazard related and may cause equipmentor property damage.

NOTICE

GENERAL SAFETY NOTICES

When working with electrical or electronic controls, make

sure that the power source has been locked out and

tagged according to OSHA regulations and approved local

electrical codes.

DANGER!

Damage or debris may fall into electrical components

causing failure or severe equipment damage, when drilling

holes in the box.

DO NOT turn control box upside down or go too deeply

into the box.

NOTICE

Make sure to barricade the door opening on both sides to

prevent unauthorized use until the door has been

completely installed.

WARNING!

In freezer and cooler applications where a conduit passes

from a warm to cold temperature zone, the conduit must be

plugged with epoxy. This will help prevent condensation

from forming in the conduit. For more information, see

Section 300-7a of the National Electric Code.

NOTICE

Do not drill holes on top of control box to run conduit, as

dust particles and moisture may cause damage to electrical

components. The safest location is at the bottom. Failure to

do so will void warranty.

NOTICE

A qualified electrician should install the wiring in

accordance with local and national electrical codes.

Use lockout and tagout procedures to avoid injury.

DANGER!

To reduce risk of injury or death, an earth ground

connection MUST BE made to the green/yellow control

box ground terminal. If metal conduit is used as the

ground connector, an N.E.C. approved ground bushing

and green/yellow wire MUST BE properly attached to the

conduit for connection to the ground terminal.

DANGER!


TO PREVENT DAMAGE TO CONTENTS, STORE

DRY BETWEEN 40° AND 80° F.

NOTE: Depending on size, the DEFENDER can

be installed either as a free standing unit or

mounted to a machine structure.

It is important to verify the following basic

information before starting with the installation.

1. Alternate dimensions in brackets are in [millimeters].

2. Make sure that you are working at the correct

location and that you have the required work

permits.

3. Does the customer wish to be present to observe?

4. How will the work area be barricaded?

5. Are any special work permits required?

6. Inspect the site to make sure that there are no

overhead obstructions (sprinkler pipes, HVAC

systems, electrical supply lines, etc.) that might

interfere with the installation.

7. Detour material handling equipment during the

installation.

8. Make sure that the correct electrical power is

supplied to the door control box and can be shut off

without interfering with other plant operations.

9. In the case of multiple doors being installed, it is

imperative to install the proper control box with the

matching door unit. The serial # for your door is on

a label located on the side of the control box and

lower track.

10. Which workstation and which side of the workstation

is the unit to be located?

11. Is anything buried in the floor where the anchors go.

12. Verify unit will fit into the location.

13. Does the installation allow for clearance for robotic,

machining, welding or other types of operation?

14. Does the installation meet all applicable robotic,

machining, welding or other workstation safety

requirements such as is contained in the following:

a.OSHA Instruction CPL 2-1.24 (Mechanical Power

Presses)

b. UL Standard for Safety UL 325 (Door, Gate, Louver

and Window Operators Systems)

c. ANSI RIA R 15.06-1999 (Industrial Robots and

Robot Systems Safety Requirements)

d.CSA Z434-03 (Industrial Robots and Robot

Systems - General Safety Requirements)

CSA Z432-04 (Safeguarding of Machinery)

15. If the measurements do not agree, STOP! Contact

your RITE-HITE MACHINE GUARDING

representative.

16. Can the lifting device lift the assem bly into position?

Are there any overhead obstructions?

17. Is a qualified electrician ready to bring in the power

and wire up the control box?

18. Can electrical power to the workstation be shut off

without interfering with other plant operations?

19. Check that floor is in sound condition and does not

have cracks or other flaws so that the header will be

level and the guides will be plumb.

20. Plan the installation so that it will not interfere with

the machining, welding or other work processes of

the workstation.

21. Using a laser level, determine if the floor is level. If

the floor is not level to within 1/8in [3mm] shimming

will be required.

22. Install optional equipment after verifying door

operation.

NOTE: Electrical prints included in the parts or

control box, supercede any prints included in

this owner’s manual on Pages 15 - 17. Always

check for electrical prints.

AMEN00040 2018-06-28

SAFETY WARNINGS


Make sure that the assembly is securely attached to

the forklift to avoid injury due to equipment slipping

or falling. Make sure that work area is barricaded to

prevent the potential of unauthorized personnel

entering the area and becoming injured. Make sure

that no one is standing under the assembly while it

is being lifted. Ensure that all workers are wearing

head, eye and foot protection.

WARNING!!!!

A floor that is not sound and level may cause

personal injury and/or equipment damage due to

failure or collapse of the GUARDIAN DEFENDER.

WARNING!!!!


1. Remove upper sideframe cover(s) (A).

2. Stand support posts (B) in the position to be

installed. Make sure they are properly oriented,

square to each other and plumb.

3. Inside to Inside of frames = Overall Ordered Width

(C).

4. Mark and drill anchor mounting holes w/leg toward

inside (D).

Plumb and square posts and anchor to the floor (4

places) with minimum 3/8in [M10] anchors.

NOTE:

Shim as necessary, using solid plastic or metal to

fully support posts. Drill through shims to allow

for proper installation of anchor bolts.

5. Slide bearing lock collar (E) onto shaft with recess

facing out tight against the spacer. Facing end of

shaft, tighten lock collar by turning clockwise until

snug. A hammer and punch are required to rotate

and tighten the lock collar, tighten set screw,

Figure 2.

6. Install bearing plate assembly (F) to the roller tube

on the drive and non-drive sides.

7. Install drive sprocket and taper lock bushing flush

with end of the shaft. Alternately torque set screws

to 175 in/lbs [20 N-m]. Re-check after initial break

in period and periodically thereafter.

8. Place roller tube (G) on lift or strap and lift into

place.

9. Slide shaft into the notch (H) on the support post

and align bearing plate with the (4) holes. Fasten

using 3/8in [M10] carriage bolts (from outside) and

lock nut. Torque bolts to 80 ft/lbs and repeat for

opposite side.

10. Fasten lower front track to upper front track at the

splice, (J) using the (4) 5/16in [M8] bolt, flat washer

and lock nuts each side.

11. Attach front track to inside face (K) of the bearing

plates using the (3) 3/8in [M10] carriage bolts, lock

nuts on front of support, per side. Tracks may need

to be flexed to align and assemble.

12. Plumb, square and fasten to the floor using

minimum 3/8in [M10] anchors (L). Cross dimension

should be the same (M).

13. Clear Opening Width = Overall opening width

minus 12in [305mm] (When fastened to the support

post (N).

14. Front guide height (O).

15. Opening depth plus 13 1/8in [333mm] (P).

AMEN00040 2018-06-28


SUPPORT POST INSTALLATION

A

Figure 1

B

DC

6 Publication: AMEN00040 2020-07-06AMEN00040 2018-06-28

ROLLTOP™ MODEL 1325ROLLTOP™ MODEL 1325

ROLLER TUBE / FRONT TRACK INSTALLATION

Figure 2

Figure 3

E

F

G

H

J

K

N

O

P

Publication: AMEN00040 2020-07-06 7 AMEN00040 2018-06-28


FRONT TRACK INSTALLATION

Figure 4

L

M

An unsound and/or unlevel floor may cause the

RollTop to collapse or fail resulting in personal

injury and/or equipment damage.

CAUTION ! ! !!

Make sure that the assembly is securely attached to

the forklift to avoid injury due to equipment slipping

or falling. Make sure that work area is barricaded to

prevent the potential of unauthorized personnel

entering the area and becoming injured. Make sure

that no one is standing under the assembly while it is

being lifted. Ensure that all workers are wearing head,

eye and foot protection.

WARNING!!!!Lock collar MUST be tight against the spacer.

Fasten to the bearing plate and tighten set

screw.

NOTICE


1. Fasten drive assembly (A) mounting bracket (B) to

the support post using (3) 3/8in [M10] carriage bolts,

washers and lock nuts provided (C). Push to top of

slots and tighten bolts.

2. Apply a grease lubricant or anti-seize (not supplied)

to the drive shaft (D) to ease installation and

maintenance of gearbox. Slide sprocket/shaft

assembly through the support post and into the

gearbox shaft.

3. Install 1/4in x 3/16in [6mm x 5mm] key into the

keyway from the back side until it is past the

retaining ring slot. The key should slide freely,

forcing the key may cause distortion.

4. Gearbox case should be flush with the end of the

retaining ring groove. Install retaining ring (E) into

shaft groove.

5. Install #50 drive chain (F) onto sprockets.

6. Place sprocket (G) flush with the end of the limit

switch shaft. Tighten the set screws onto the shaft

with allen wrench to 75 in/lbs [9 N-m} and apply

thread locking compond.

7. Install #35 limit switch chain (H) onto sprockets,

place connector link onto chain and lock in place.

8. Tighten chain by loosening drive mounting bracket,

pulling toward floor, and then tighten bolts (J).

9. To adjust limit switch chain, loosen the limit switch

mounting bolts (K) and adjust so the chain deflects

approximately 1/4 [6mm]. More than 1/4in [6mm]

may cause wear on the limit switch shaft bearing

assembly. Make sure chain is tight enough so it

does not slip over the teeth.

10. After install is complete, remove gearbox oil vent

plug (M).

11. If after installation the curtain is not tracking

squarely, manually lower the curtain to expose the

hook / loop fastener (N) on the roller tube and

curtain. Loosen the curtain from one of the ends and

raise or lower the curtain based on the direction the

curtain is tracking. Distance should be 5/8in [16mm]

from curtain to upper guide, guides may need to be

flexed to square properly.

NOTE:

The motor and brake cable is pre-wired into

the motor junction box, but needs to be

terminated to the controls later in the

installation process. Electrical drawings are

located in the control box or parts box and on

Pages 15 - 17.


DRIVE INSTALLATION


Figure 5

A

B

C



P - Roller

Q - Spacer

R - Retainer

S - Optional roller with interlock

T - Optional actuator

DRIVE INSTALLATION

Figure 7

Figure 6

D

F

E

G

H

J

K

M

N

T

S

R

Q

P


NOTE:

The RollTop may be wired directly into the

workstation control system.

Flexible non-metallic conduit must be

securely fastened at least every 3ft [914mm]

to meet National Electrical Code

requirements (N.E.C. 351-27).

All necessary wiring diagrams are on

Pages 15 - 17.

The following is the responsibility of the installing

electrician.

a. All local, state, and national electrical codes are met.

b. Electrical service up to the control box with proper

branch service protection and an approved means

of disconnect.

CONTROL BOX INSTALL

1. Install control box (A) approximately 54in [1.4M] (B)

from the floor and remote disconnect (supplied by

others), Figure 8.

2. The control box is provided with class CC

protective fusing for the incoming power. The

incoming power terminals in the control box will not

accommodate wires larger than 10AWG.

3. Install electrical conduit between motor junction

box, control box and remote disconnect. All

connections to control box must be through the

bottom (C).

4. The OPEN button (D) opens the curtain and resets

the curtain after a fault condition. To open, press

the button, you do not have to press and hold the

button. When you take your finger off the button,

the button springs back to its normal position.

5. The STOP button (E) stops the curtain operation at

any time during its travel.

6. The CLOSE button (F) closes the curtain. To

close, press the button.

NO CONTROL BOX INSTALL

1. Assemble components necessary to control 3

phase power at either 208, 230, 400, 460 or 575V.

2. Terminals 3 & 4 on the Bridge Rectifier (Located in

the motor junction box) should be switched with

auxiliary N.O. dry contacts on motor contactors to

release the brake when motor is running. The

contacts should close when the motor is running to

release the brake. Wires 4 & 5 in the supplied

motor harness are wired into terminals 3 & 4 on the

Bridge Rectifier. See Motor / Brake Electrical

Schematic on Page 12 for wiring.

AMEN00040 2018-06-28


ELECTRICAL INSTALLATION

Figure 8

A

B

C

E

D

F

When working with electrical or electronic controls, make

sure that the power source has been locked out and

tagged according to OSHA regulations and approved local

electrical codes.

DANGER!

A qualified electrician should install the wiring in

accordance with local and national electrical codes.

Use lockout and tagout procedures to avoid injury.

DANGER!

To reduce risk of injury or death, an earth ground

connection MUST BE made to the green/yellow control

box ground terminal. If metal conduit is used as the

ground connector, an N.E.C. approved ground bushing

and green/yellow wire MUST BE properly attached to the

conduit for connection to the ground terminal.

DANGER!

Make sure to barricade the door opening on both sides to

prevent unauthorized use until the door has been

completely installed.

WARNING!

Do not drill holes on top of control box to run conduit, as

dust particles and moisture may cause damage to electrical

components. The safest location is at the bottom. Failure to

do so will void warranty.

NOTICE

Damage or debris may fall into electrical components

causing failure or severe equipment damage, when drilling

holes in the box.

DO NOT turn control box upside down or go too deeply

into the box.

NOTICE


REVERSING PHOTOEYE

Locate the photoeye components (receiver (A),

reflector (B), hardware and mounting brackets (C)).

The photoeye sends a beam that is reflected back by

the reflector to the receiver. If the light beam is

blocked the photoeye contact is actuated sending an

open command until the item blocking the beam is

removed. The action is to prevent the curtain from

being lowered on someone or some item.

1. Attach the receiver photoeye bracket to the front

drive side track (D) at the pre-drilled holes.

2. Attach the reflector bracket to the front non-drive

side track (E) at the pre-drilled holes.

3. Route and connect the wires to the terminal strip.

4. To set the vertical alignment loosen the mounting

bracket attachment bolts slightly and rotate the

mounting bracket until the RED and GREEN LEDs

turn on. Continue to rotate the bracket until the

LEDs turn off. Rotate the bracket back half the

distance and tighten the mounting bolts. Yellow

LED indicates unit has power.

5. To set the horizontal alignment loosen the lock ring

and sweep photoeye left or right until the RED and

GREEN LEDs turn on. Continue to rotate the

photoeye assembly until the LEDs turn off. Rotate

the photoeye back half the distance and tighten the

lock ring.

6. Locate the light/dark operate switch on the back

end of the receiver unit. Make sure that the switch

is set to the light position.

AMEN00040 2018-06-28


PHOTOEYE ADJUSTMENT

Figure 9

A

B

C

D E


1. Manually release brake and raise or lower the

curtain to the proper full open position.

2. Loosen the two phillips screws and remove cover.

3. With curtain 2in [51mm] below the opening height,

set open limit switch.

4. Loosen the center locking screw and turn the open

limit switch cam locking screw labeled #2 until you

hear the contact click, Figure 10. Pay attention to

rotation of the cam so when limit is adjusted, it will

be on the proper side of the large cam.

a.For a Right Hand Drive door, the roller tube and limit

shaft turn clockwise to lower and counter-clockwise

to raise the door. Turn the #2 open limit switch

screw counter-clockwise to lower the door and

clockwise to raise the door.

b.For a Left Hand Drive door, the roller tube and limit

shaft turn counter-clockwise to lower and clockwise

to raise the door. Turn the #2 open limit switch

screw clockwise to lower the door and counter-

clockwise to raise the door.

5. Manually release brake and lower to closed position.

6. To adjust the closed limit switch, loosen locking

screw and turn the cam screw labeled #1 until you

hear the contact click, Figure 10.

a.For a Right Hand Drive door, turn the #1 close limit

switch screw clockwise to lower the door and

counter-clockwise to raise the door.

b.For a Left Hand Drive door, turn the #1 close limit

switch screw counter-clockwise to lower the door

and clockwise to raise the door.

7. Fine tuning of the limits may be necessary. This will

be determined by running the door up and down.

8. The limit switches are normally closed and will open

when the limit cam lobe is tripped or activated.

9. Replace limit switch cover and chain guard with M5

bolts.

AMEN00040 2018-06-28


LIMIT SWITCH ADJUSTMENT

Figure 10

A

A - Standard Wiring

B - Partial Open Wiring

C - 208/230V Wiring

D - 460V Wiring

E - 400/575V Wiring

F - Contact block Wiring

G - Center locking screw

H - Open Limit

J - Close Limit

K - Partial Open Limit

L - #1 Close Limit Screw

M - #2 Open Limit Screw

N - White

P - Orange

Q - Red

R - Green

S - Black

T - Blue

R

S

P

N

MK

J

H

G

F

EDC

B

Q

L

P

N

R

QT

H

J


COVERS AND SHROUDS

1. After unit is functional, use the (6) screws (A) per

side provided to fasten covers (B) to the support

post (C) sides. 5/16in [8mm] nut driver is required.

2. After unit is functional, use the (12) 3/8in [M10]

bolts and nuts (D) provided to fasten shroud (E) to

the bearing plates (F).

NON-CONTACT INTERLOCK

NOTE: The Non-Contact interlock (A) transmits a

coded signal from the controller through the

switch. The actuator modifies the received

signal and resends it to the controller via the

switch. The switch is located on a sliding

bracket in the bottom of the front curtain

guide (B). The actuator (C) is installed on the

curtain bottom bar.

1. Secure controller on din rail inside enclosure.

2. Wire switch and controller as shown on Page 17.

Secure switch wiring as required.

3. Adjust the switch to minimize the distance to the

actuator when the curtain is closed, Figure 7.

4. The LED indicator on the switch is green when

actuator is within range and indicates the safety

circuit is closed and the unit is closed. A red LED

indicates the actuator is out of range, the safety

circuit is open, and the unit is open. A flashing

green/red LED indicates the actuator is in range

and unit is closed, but the safety circuit is open.

5. The Lever Arm Interlock (D) is factory installed and

not adjustable, the limit switch must be adjusted to

stop the curtain bottom barrier bar in the proper

position.

ACTIVATION DEVICES

Operate the system with any remote activation devices

that are in use. Make sure that the curtain fully opens

and then closes after given the command to close.

AMEN00040 2018-06-28


SHROUD / INTERLOCK INSTALLATION

Figure 13

Figure 11

Figure 12

A

BC

D

F

E

A

B

C BD

Make sure switch is wired directly into the safety

control circuit, so that the machine will shut

down if the switch is defective or the curtain is

not down.

NOTICE


POWER UP/START UP

1. Turn on power to the control box.

2. Position the barrier curtain in the center of its travel.

3. Press the OPEN button, the roller should turn sothat the curtain would be raised. Be prepared topress the stop button, in case the motor windingis phased incorrectly and causes the roller toturn the wrong way.

4. If roller turns the wrong way, immediately stop thedoor. To reverse the phase, disconnect power, lockand tag out. Reverse leads T1 and T2 in the controlbox. Reconnect power and check operation.

5. Press the CLOSE button, the roller should turn sothat if the curtain would be lowered.

OPERATING CONDITIONS

1. Operate the curtain under normal conditions.

Observe the curtain opening to make sure that it

opens fully and does not open too far. Observe the

closing action to make sure that the curtain operates

smoothly, and fully closes without excessive curtain

ripple near the bottom.

2. While the curtain is closing, block the reversing

photoeye. The unit should open immediately.

3. Make sure interlock switch in curtain guide is

aligned with the barrier bar so that the interlocked

machine or equipment will not operate unless

curtain is closed.


MAINTENANCE / TROUBLESHOOTING

RITE-HITE MACHINE GUARDING PLANNED MAINTENANCE

Model 1325 ROLLTOP™

CUSTOMER:

RHC# SERIAL# DATE:

Periodic Cycle Check:

Planned Maintenance

Activation Devices

Chain

Curtain

Electrical Connections

Frame and Hardware

Interlocks (optional)

Labels and Instructions

Limit Switch

Photoeyes and Reflectors

Recommended P.M. Intervals

(Time Shown In Months)

1

•

Inspect and Perform the Following (See Manual)

Check for proper operation.

The break-in period is 30 days or 50,000 cycles.

Tension must be maintained.

Operate to verify proper operation. Clean with warm

non abrasive soapy water. Check for damage or

wear and repair any tears.

Perform visual inspection and tighten.

Perform visual inspection and tighten. Blow dust

and dirt from the frame assembly.

Verify switch shuts off the proper machine

components when activated.

Replace if missing.

Make sure barrier curtain stops at the proper open

and closed positions. Inspect chain and sprockets

for wear, and lubricate.

Clean and check for proper operation. Barrier

curtain must reverse when the beam is blocked.

4

•

•

•

•

•

•

•

8

•

12

•

•

•

•

•

•

•

•

•

18 24

•

•

•

•

•

•

•

30 36

•

•

•

•

•

•

•

•

•

PROBLEM REMEDYControl Box (Optional) The control box contains the necessary motor starters, relays, transformers, etc. to safely control 3 Ø

power, open, close and stop push buttons. If control box does not power up, check fuses and replaceas needed.

Curtain The curtain provides a safety barrier against sparks, harmful light emissions and physical contact with the machine by the operator. The curtain is manufactured of nylon reinforced material. Barrier bars are sewn into add rigidity. Vision window is available as an option.

Curtain remains open, Reversing photoeye alignment incorrect. (Red LED on photoeye off.) Realign photoeye. does not close Photoeye not set to light operate. Open reversing photoeye cover to check switch position. Fuse blown,

Replace fuse after checking for shorts. Check all connectors for proper connection. Stop button pushed when door was in open position. Press close button.

Curtain does not stop Limit switch positioning incorrect. Ensure that the limit switches are properly positioned. Failed limit switch, at limits. check for continuity, replace if necessary.

Curtain travel reversed. Motor phases reversed. Remove power, reverse wires in terminals T1 & T2.

Curtain will not go up Loss of power. Verify that electrical power is getting to the control box. Bad fuse, check fuses. Make sure or down. nothing is blocking the path of any photoeye light beam.

Curtain tracks off Curtain misaligned. Curtain may need to be adjusted on the hook and loop fastener. Both vertical supportto one side. columns must be plumb and level. The distance between columns must be the same when measured at

the top and bottom. Shim or remount as required.

Interlock Devices The interlock keeps the machine from functioning unless the curtain is in position. The interlock mounts in (Optional) the bottom of the support post and is activated by the curtain when it comes into the closed position.

Limit Assembly If limits come out of adjustment, make sure the center locking screw is tightened down. For rewiring of the limit switch, see Page 12.

Motor Assembly The motor assembly includes the motor, gearbox, brake and limit switch. The motor assembly unrolls and lowers the curtain before the machine cycle begins and rolls the curtain back up when the machine cycle iscomplete. For rewiring of the motor, see Page 12. If motor does not run, look for loose connections, checkall connections in terminals T1, T2, T3, and the connectors. Brake not releasing. Check brake connections.



FIELD WIRING DIAGRAM

OPE

N L

.S.

OPT

ION

AL IN

PUTS

FO

R E

XTER

NAL

OPE

N/C

LOSE

/STO

P IN

PUTS

FR

OM

CU

STO

MER

SU

PPLI

ED P

USH

BUTT

ON

S O

R P

LC O

UTP

UTS

.

EXTE

RN

AL

CLO

SE IN

PUT

EXTE

RN

ALST

OP

INPU

T

ACSTP

PB2

LS2

EXTE

RN

AL

OPE

N IN

PUT

SET

TO L

IGH

T O

PER

ATE

NC

PB1

AC CO

MBU

AC PE1

ACBRO

GBK

AC LS1

WH

T

RED

NC

CLO

SE L

.S.

LOW

VO

LTAG

E TE

RM

INAL

S

(LES

S TH

AN 3

0 VO

LTS)

AC LS2

OR

G

GR

N

SHO

WN

WIT

H G

UAR

D O

PEN

OPT

ION

AL IN

TER

LOC

K

SWIT

CH

WIR

ING

NC

NO

NC

END

USE

R'S

SAFE

TY

STO

P

CIR

CU

IT

RED

CLE

AR

GR

EEN

OR

ANG

E

3433

BLU

E

21 2212

13 F

EET

OF

22 A

.W.G

.

6 C

ON

DU

CTO

R C

ABLE

BLAC

K11

REV

ERSI

NG

PH

OTO

EYE

#1

** N

OTE

: EN

D U

SER

MU

ST

PRO

VID

E D

ISC

ON

NEC

T AN

D

BRAN

CH

CIR

CU

IT P

RO

TEC

TIO

N.

NO

TE: R

EVER

SE W

IRES

IN

TER

MIN

ALS

U &

V T

O C

HAN

GE

MO

TOR

RO

TATI

ON

BRK1

MTR

1

(GR

EATE

R T

HAN

100

VO

LTS)

HIG

H V

OLT

AGE

TER

MIN

ALS

B2BK

#5

BK#3

B1BK

#4

BK#1

BK#2

GN

UPE

INC

OM

ING

PO

WER

3�

PE

L1 L2 L3PE

SET

TO L

IGH

T O

PER

ATE

BU

PE1

PE2

BRR

EVER

SIN

G P

HO

TO E

YE #

2

OPE

N L

.S.

NO

3 4BL

K

BLU

NO

CLO

SE L

.S.

1 2BR

N

YEL

OGBK

CO

M

AC

ADD

ITIO

NAL

TER

MIN

ALS

PRO

VID

ED F

OR

LIM

IT

SWIT

CH

FEE

DBA

CK

NO

TE:

REM

OVE

FAC

TOR

Y

INST

ALLE

D J

UM

PER

BET

WEE

N

PE1

AND

PE2

TO

INST

ALL

SEC

ON

D P

HO

TOEY

E

NO

TE:

REM

OVE

FAC

TOR

Y

INST

ALLE

D J

UM

PER

BET

WEE

N

STP

AND

AC

TO

EN

ABLE

EXTE

RN

AL S

TOP

V W

1 3 2 4

BU BR BK

GN

/YE

CU

2

SN4

CU

1

SN3

REV

ERSI

NG

ED

GE

CU

2

SN4

CU

1

SN3

1 3 2 4

PED

RAI

N/B

RAI

D

BK#6

TRIM

FO

IL S

HEA

TH

NO

T U

SED

FO

R 1

325

& 13

90

UN

ITS

WIT

H IR

BR

AKE

REL

AY



CONTROL BOX WIRING DIAGRAM

PA

RT

#

MO

DE

L N

UM

BE

R

C

AP

PR

OV

ED

BY

CR

REV SHEET DWGNO

DE

SC

RIP

TIO

NQ

TY

PA

RT

NO

.IT

EM

PA

RT

S L

IST

/ M

AT

ER

IAL

NE

XT

AS

SE

MB

LY

RE

V

RE

VIS

ION

HIS

TO

RY

DE

SC

RIP

TIO

NE

CN

DA

TE

AP

PR

OV

ED

BY

DA

TE

DW

G N

O

0.0

05

0.1

25

0

0.0

30

0.0

20

0.0

10

0.1

25

0.1

00

0.0

60

0.0

40

80

+/-

1 D

EG

AN

GLE

S

FIN

ISH

-

40

155

1.2

5

0.2

5

0.1

25

40

80

15

1.2

5

5

0.2

5

INIT

IAL

EC

N

RE

F

DR

AW

N B

Y

CH

EC

KE

D B

Y

SC

ALE

SIZ

E

MM

-DD

-YY

DA

TE

DA

TE

TIT

LE

DO

NO

T S

CA

LE

DR

AW

ING

+ /

-

INC

H T

OL

ER

AN

CE

S

OV

ER

UP

TO

SH

EE

T

RE

V

R

DA

TE

IS

SU

ED

RIT

E-H

ITE

DO

OR

S I

NC

.

5210E

030

RIT

E-H

ITE

DO

OR

S IN

C.

9"=

1'

C

MA

CH

INE

GU

AR

DIN

G

WIR

ING

DIA

GR

AM

134

0/5

0/6

0

1746

LIP

9/2

0/2

007

5537

11/2

/2007

20

07

AA

DD

PO

WE

R S

UP

PLY

FO

R P

ILZ

OP

TIO

N6168

9/1

/2010

LIP

BIR

RE

LA

Y F

OR

1390

6967

12/1

1/2

014

TA

H

CA

DD

IR

RE

LA

Y F

OR

1325

7486

2/5

/2018

SH

C



NON-CONTACT INTERLOCK & MOTOR/BRAKE WIRING

4

2

T5T6

T9T8

~ L2(N)

T7

T4

T1

~ L1 1

6

5

FULL WAVE

RECTIFIER

(BLACK)

3

BRAKE COIL

BRAKE CONTACTSTHESE CONTACTS SHOULD BE

SWITCHED W. AUX DRY CONTACT ON

MOTOR CONTACTORS. CONTACT

SHOULD CLOSE WHEN MOTOR IS

RUNNING.

460V MOTOR WINDINGS

PE

T3 T2

MOTOR/BRAKE/GEARBOX

INCOMING POWER

FROM RITE-HITE CONTROL

BOX OR CUSTOMER

CONTROLS

PE

FULL WAVE

RECTIFIER

(BLACK)

T7

MOTOR/BRAKE/GEARBOX

230V MOTOR WINDINGS

L1

T4-T5-T6

L3L2 T9 T8 FROM RITE-HITE CONTROL

BOX OR CUSTOMER

CONTROLS

INCOMING POWER

U1

U2-V2-W2

W1V1

575V MOTOR WINDINGS

~ L2(N) 2

MOTOR/BRAKE/GEARBOX

HALF WAVE

RECTIFIER

(GRAY)

~ L1 1

INCOMING POWER


BOX OR CUSTOMER

CONTROLS

PE

4

2~ L2(N)

~ L1 1

6

5

3

BRAKE COIL





RUNNING.

4

6

5

3

BRAKE COIL





RUNNING.

PART #

MODEL NUMBER

CR

R

BY APPROVEDDATEECNDESCRIPTION

REVISION HISTORY

REV

3

DESCRIPTIONQTY PART NO.ITEM

PARTS LIST / MATERIAL

NEXT ASSEMBLY

REV

SHEET

UP TOOVER

INCH TOLERANCES

+ / -DO NOT SCALE DRAWING

TITLE

DATE

DATE

MM-DD-YY

SIZE

SCALE

B

CHECKED BY

APPROVED BY

DRAWN BY

REF

INITIAL ECN

DATE ISSUED

0.25

5

1.25

15

80

40

0.125

0.25

1.25

5

15

40

FINISH

ANGLES +/- 1 DEG

80

0.040

0.060

0.100

0.125

0.010

0.020

0.030

0 0.125 0.005

DWG NO

DATE

RITE-HITE DOORS INC.

5210E026

RITE-HITEDOORS INC.

6"=1'

C

C

MOTOR/BRAKE SCHEMATIC

1340/50/60

AJW 8/4/2003

4225

8/15/2003

2003

A MISC CHANGES 4901 11/11/2005 RJK

B 575V = 250VDC, was 205VDC 4901 5/16/2006 MDB

C ADD 400V 50/60 HZ OPTION 5420 6/28/2007 DAS

U1

U2-V2-W2

W1V1

400V MOTOR WINDINGS

~ L2(N) 2

MOTOR/BRAKE/GEARBOX

~ L1

INCOMING POWER


BOX OR CUSTOMER

CONTROLS

PE

BRAKE COIL





RUNNING.

FULL WAVE

RECTIFIER

(BLACK)

41

6

5

3

205

VDC

~230

VAC

~265

VAC

~460

VAC

~575

VAC

250

VDC

~400

VAC

205

VDC

205

VDC

~230

VAC

~230

VAC

WHITE

BROWN /

PINK

GREEN

YELLOW

BLUE

GREY

RED

24V

SIGNAL

SIGNAL

SIGNAL

0V

PLC

FEEDBACK

NOT USED

SIGNAL

PIL

Z P

SE

N C

S 1

.1P

CO

DE

D S

WIT

CH

PIL

Z P

NO

Z X

2.8P

CO

NT

RO

LLE

R

24VDC

0VDC

RESET

-0V AC/DC

+24V AC/DC

S22

S21

S52

S12

S34

S11

A1

A2

INCOMING

POWER 24V

AC/DC

INCOMING

POWER 24V

AC/DC

RED

GREY

BLUE

YELLOW

GREEN

PINK

BROWN

WHITE

PIL

Z P

SE

N C

S 1

.1P

CO

DE

D S

WIT

CH

SIGNAL

NOT USED

PLC FEEDBACK

SIGNAL

0V

SIGNAL

24V

SIGNAL

PIL

Z P

NO

Z X

2.8P

CO

NT

RO

LLE

R

S12

S22

S21

S52

0VDC

S34

S11

A2

A1

RESET

24VDC

-0V AC/DC

+24V AC/DC

PLC

FEEDBACK

PIL

Z P

SE

N C

S 1

.1P

CO

DE

D S

WIT

CH

GREY

REDNOT USED

WHITE

BROWN

PINK

GREEN

YELLOW

BLUE

SIGNAL

0V

SIGNAL

SIGNAL

24V

SIGNAL

/ ORANGE

BLACK

/ ORANGE

BLACK

PART #

MODEL NUMBER

CR

R

BY APPROVEDDATEECNDESCRIPTION

REVISION HISTORY

REV

DESCRIPTIONQTY PART NO.ITEM

PARTS LIST / MATERIAL

NEXT ASSEMBLY

REV

SHEET

UP TOOVER

INCH TOLERANCES

+ / -DO NOT SCALE DRAWING

TITLE

DATE

DATE

MM-DD-YY

SIZE

SCALE

B

CHECKED BY

APPROVED BY

DRAWN BY

REF

INITIAL ECN

DATE ISSUED

0.25

5

1.25

15

80

40

0.125

0.25

1.25

5

15

40

FINISH

ANGLES +/- 1 DEG

80

0.040

0.060

0.100

0.125

0.010

0.020

0.030

0 0.125 0.005

DWG NO

DATE

RITE-HITE DOORS INC.

5270E002

RITE-HITEDOORS INC.

1"=1"

A

WIRING, PILZ, NON CONTACT INTERLOCK

1325

6/28/2005

4901

11/1/2005

2005

A ADD POWER SUPPLY FOR PILZ OPTION 6168 9/1/2010 LIP

24V

DC

PO

WE

R S

UP

PLY

0V (

-)24

V (

+)

24V

DC

PO

WE

R S

UP

PLY

0V (

-)24

V (

+)



ROLLTOP SERVICE PARTS

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

3

2

40

5

15

1

7

76

22

57

31

27

34

32

59

19

49

24

23

25

4

37

39

11

36

77

26

9

38

57

48

47

33

16

18

21

47

10

20

11

10

11

11

9

58

56

45

67

18

2223

21

57

47

35

574

47

28

71

1755

68

31

12

50

63

14

62

41

52

74

42

44

69

54

61

53

63

72

62

64

41

43

52

42

51

12

50

63

13

62

60

68

75

73

35

78

46

6

79

81

80

30

66



ROLLTOP SERVICE PARTS LISTITEM QTY DESCRIPTION PART NUMBER

1 1 Roller Tube Weldment (includes 2” PSA hook fastener) 67482 a/r Roller Tube, Hook Fastener, 2” PSA 740000203 2 Bearing, Fafnir 125000234 4 Bearing Flange Mount 457500015 2 Bearing Plate Kit (includes #’s: 3, 4, 6, 47, 57) 537005176 2 Plate, Bearing 650005287 1 Shroud 6941

8 -9 1/1 Guide, Assembly, Front, Lower, Right or Left 5142

10 2 Guide, Assembly, Front, Upper, Right or Left 514411 a/r Guide, Front, Loop Fastener, 2”, FR 7400007112 2 Photoeye, Bracket 1450002413 1 Photoeye, Retro-Reflective 6390000214 1 Photoeye, Reflector 6640000115 1 Retainer, Bottom Loop, Standard 6680001216 1 Retainer, Bottom Loop, Non-Contact Interlock 6680001317 2 Shim, Front Track 6900001318 1/1 Support Post, Rear, Right or Left 725319 2 Support Post, Rear, Cover 17900126

20 1 Curtain Assembly 287221 5 Curtain, Barrier Bar, Assembly 645222 2 Spacer, Bottom Bar, Roller 7045011223 10 Roller, Barrier Bar 6720007324 2 Roller, Barrier Bottom Bar, Non-Contact 67200084

25 1 Motor, Assembly 553326 1 Motor, Starter Set 553427 3 Bolt, Carriage, 3/8-16 x 1 1/2, Z5 6788001228 1 Rectifier, Bridge, 2A, 110-230V (for 230/460V doors) 6627000929 -30 1 Plate, Motor, Mach, 172.1,1325 (=>1/1/2018) 6500096431 a/r Motor, Cable 154832 1 Bushing, Taper Lock, 1” x 1 1/4” Bore 1555005233 1 Sprocket, Limit Switch, Driven 7080001234 1 Sprocket, Taper Lock, 20 Tooth, #50 7080003435 1 Shaft, Weldment, Drive, 172.1,1325 (=>1/1/2018) 6895019936 2 Ring, Retaining, Ext, 1.0” x .042 6702001637 5’ Chain, Drive, #50 1660001738 1.3’ Chain, Drive, #35 1660001939 1 Chain, Connector Link, #35 5440000840 1 Chain, Connector Link, #50 54400011

41 2 Connector, Straight, L/T, 1/2 (interlock) 1696000242 2 Grommet, Rubber (interlock) 5128000243 4 Nut, Hex, Nylon, Lock, #10-24, znc (Non-Contact) 5560000444 4 Nut, Hex, Nylon, Lock, 1/4-20, znc (shim, limit switch) 5561000145 8 Nut, Hex, Nylon, Lock, 5/16-18, znc (splice) 5562001046 3 Bolt, Carriage, 3/8-16 x 1 1/2, Z5 6788001247 20 Nut, Hex, Nylon, Lock, 3/8-16, znc (bearing, shroud, support post) 5563000548 a/r Rivet, 2pc, 1 7/8, SSLM-8SP-30, Blk (curtain) 66860007

49 12 Screw, HWH, Self Drill/Tap, #12-14 x 3/4” (support post covers) 6785000450 4 Screw, RHPS, Phillips, #10-24 x 1/2”, znc (photoeye, reflector) 6785000851 2 Screw, RHMS, Phillips, #8-32 x 1/2”, znc (Non-Contact Interlock) 6785001752 2/2 Screw, RHMS, Phillips, #10-24 x 1, znc (Non-Contact or Lever Arm Interlock) 6785002453 8 Screw, RHMS, Phillips, #10-24 x 3/4”, znc (Non-Contact) 6785003054 2 Bolt, Carriage, 1/4-20 x 3/4, GR 5, znc (motor) 6786002355 4 Screw, FHMS, Allen, 1/4-20 x 3/4” (shim) 6786004256 8 Screw, HHMS, 5/16-18 x 3/4, GR 5, znc (splice) 6787000657 6/12/15 Bolt, Carriage, 3/8-16 x 1”, GR 5, znc (bearing, shroud, support post) 6788009258 2 Bolt, Shoulder, 5/8 x 2 1/2” (non-contact roller) 6791000859 a/r Bolt, Shoulder, 5/8 x 1 1/2”, Self Locking (barrier bar roller) 6791003060 3 Screw, HHMS, M8-1.25 x 25, Z8.8 (limit switch) 6793000561 4 Screw, SHCS, M8-1.25 x 22, ZNC, 12.9 67930056

62 4/8 Washer, Lock, Split #10, znc (2 reflector, 2 photoeye, 2 Non-Contact Interlock) 7410000163 4/8 Washer, Flat, 13/64 x 1/2 x .036, znc (2 reflector, 2 photoeye, 2 Non-Contact Int) 7410000264 4/6 Washer, Lock, Split #8, znc (shim) 7410000565 - n/a66 3 Washer, Lock, Split, 5/16, znc (motor) 7412000267 16 Washer, Flat, 5/16, znc (splice) 74120003

68 a/r Cable, Limit Switch (Limit Switch Cable and Lever Arm Interlock) 1565004769 1 Plate, Limit Switch,172.1,1325 (=>1/1/2018) 6500096170 - n/a71 1 Rectifier, Bridge, 1/2 Wave, 575V 6627001272 1/2 Switch, Interlock, Non-Contact, Cable 1565024373 1/2 Switch, Interlock, Non-Contact, Plate 6500053074 1/1 Switch, Interlock, Long Arm, 2NC, 1NO 7270018375 1/2 Switch, Interlock, PILZ, Non Contact, PSEN 7270018476 1/2 Actuator, PSEN, PILZ 1020000777 1 Controller, PNOZ, PILZ 1750001278 1 Limit Switch, Lobe, 60 Deg, Cam 5515032379 1 Kit, 1325, Switch, Limit, 4 Pos (=>1/1/2018) 5370105480 1 Kit, 1325, Switch, Limit, 2 Pos (=>1/1/2018) 5370105581 1 Kit, 1325, Switch, Limit, 2 Pos (<1/1/2018) 53700964



CONTACTOR CONTROL BOX

5210E031 Rev. D

10/25/16

Control Box Layout

ITEM QTY DESCRIPTION PART NUMBER

1 1 Control Box Assembly 17462 1 Circuit Breaker, Overload, 1.6-5A 166600083 1 Contactor, Interlock, MCS 170000104 2 Contactor 24VAC, 16 AMP, 50/60Hz, 1NO 170000205 2 Contactor Auxiliary, 2NO 170000216 2 Contact, 3 Across N.O. 172000127 1 Contact, 3 Across N.C. 172000138 1 Controller, Vital 1, Jokab 175000119 1 Controller, Pnoz, Pilz 17500012

10 2 Fuse, .5AMP, 60)V, Time Delay(>= 380V) 5100000111 1/2 Fuse 1AMP, 250V, Time Delay 5100000212 1 Fuse Holder, 2 Pole, 600V, 30A 5100000313 1/2 Fuse Holder, 1 Pole,300V,12A 5100000414 2 Fuse, 1AMP, 600V, CC, Time Delay (< =240V) 5100002315 1 Power Supply, Din, 24VDC,18W 6570000616 1 Relay SPDT 12VAC 10A (Rev Edge only) 6645000217 1/2 Relay DPDT 24VAC 5A (Stand, Rev Edge or Photoeye option) 6645000318 1 Relay SPDT 24VAC 10A (photoeye option) 6645000419 1 Resistor, 200 Ohm, 10 Watt (Rev Edge only) 6655001720 2/3 Relay Socket 2 Pole (Standard, Rev Edge or Photoeye option) 7035000121 1 Relay Socket 1 Pole (Photoeye or Rev Edge option) 70350002

22 1 Switch, Push button, Red 22.5MM 7270000623 1 Switch, Push button, Green 22.5MM 7270008524 1 Switch, Push button, Yellow 22.5MM 7270008625 4 Terminal, End, Stop, Screwless 7310002426 23/25/29 Terminal, PH, Cage, 20A, 3 Hole (2 - Photoeye option or 4-Rev Edge) 7310008527 3 Terminal, PH, Cage, 20A, 3 Hole, Bar 7310008628 4 Terminal, PH, Cage, 20A, Jump, 2P 7310008129 2 Terminal, PH, Cage, 20A, 3 Hole, Gnd 7310008730 1 Transformer 100VA 208/230/460V 24/115V 7355002931 1 Transformer 100VA 380/415/575V 24/115V 73550030

3

2

29

5

151

6

23

22

7

3130246

2519

27

24

23

25

4

25

131112 14 29

26 981311 17 20 16 18 21

27

28

10


ARCHITECTURAL DRAWING ROLLTOP



RITE-HITE MACHINE GUARDING NOTES PAGE


This page intentionally left blank.


RITE-HITE MACHINE GUARDING NOTES PAGE


This page intentionally left blank.


RITE-HITE Company, LLC and its affiliates (collectively “RITE-HITE”) warrants that the RollTop unit sold to the Owner will be free ofdefects in design, materials and workmanship (ordinary wear and tear excepted) for the periods set forth below (“LimitedWarranty”).

Two (2) Year on all mechanical and electrical parts.

One (1) Year labor, based on approved travel and labor repair times.

Five (5) Year for motor, brake and gearbox material failure only.

REMEDIES

Parts. RITE-HITE’s obligations under this Limited Warranty is limited to repairing or replacing, at RITE-HITE’s option, any partwhich is determined by RITE-HITE to be defective during the applicable warranty period. Such repair or replacement shall be RITE-HITE’s sole obligation and the Owner’s exclusive remedy under this Limited Warranty.

Labor. RITE-HITE will provide warranty service without charge for labor in the first year of the warranty period. Thereafter, a chargewill apply to any repair or replacement under this Limited Warranty.

CLAIMS. Claims under this Limited Warranty must be made (i) within 30 (thirty) days after discovery and (ii) prior to expiration ofthe applicable warranty period. Claims shall be made in writing or by contacting the representative from whom the Product waspurchased directly. Owner must allow RITE-HITE or its agent, a reasonable opportunity to inspect any Product claimed to bedefective and shall, at RITE-HITE’s option, either (x) grant RITE-HITE or its agent access to Owner’s premises for the purpose ofrepairing or replacing the Product or (y) return of the Product to the RITE-HITE, f.o.b. RITE-HITE’s factory.

NOT WARRANTED. RITE-HITE does not warrant against and is not responsible for wear items such as fuses, batteries, bulbs,vision and seals. No implied warranty shall be deemed to cover, damages that result directly or indirectly from: (i) the unauthorizedmodification or repair of the Product, (ii) damage due to misuse, neglect, accident, failure to provide necessary maintenance, ornormal wear and tear of the Product, (iii) failure to follow RITE-HITE’s instructions for installation, failure to operate the Productwithin the Product’s rated capacities and/or specified design parameters, or failure to properly maintain the Product, (iv) use of theProduct in a manner that is inconsistent with RITE-HITE’s guidelines or local building codes, (v) movement, settling, distortion, orcollapse of the ground, or of improvements to which the Products are affixed, (vi) fire, flood, earthquake, elements of nature or actsof God, riots, civil disorder, war, or any other cause beyond the reasonable control of RITE-HITE, (vii) improper handling, storage,abuse, or neglect of the Product by Owner or by any third party.

DISCLAIMERS. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS ANDWARRANTIES, EXPRESS OR IMPLIED, AND RITE-HITE EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIEDWARRANTIES OF MERCHANTABILITY OR FITNESS FOR PURPOSE. RITE-HITE SHALL NOT BE SUBJECT TO ANY OTHEROBLIGATIONS OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDINGNEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO THE PRODUCTS SOLD ORSERVICES RENDERED BY RITE-HITE, OR ANY UNDERTAKINGS, ACTS, OR OMISSIONS RELATING THERETO.

LIMITATION OF LIABILITY. IN NO EVENT SHALL RITE-HITE BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL,INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RITE-HITE HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Such excluded damages include, but are not limited to, personal injury,damage to property, loss of goodwill, loss of profits, loss of use, cost of cover with any substitute product, interruption of business,or other similar indirect financial loss. Rite-Hite 2.1.14

RITE-HITE DOORS, INC. is covered by one or more of the following U.S. patents, including patents applied for, pending, or issued:

5,579,820, 5,638,883, 5,794,678, 5,887,385, 5,915,448, 5,944,086, 6,089,305, 6,145,571, 6,148,897, 6,192,960, 6,212,826,6,321,822, 6,325,195, 6,330,763, 6,360,487, 6,481,487, 6,560,927, 6,598,648, 6,612,357, 6,615,898, 6,688,374, 6,698,490,6,837,296, 6,901,703, 6,942,000, 6,964,289, 7,034,682, 7,045,764, 7,111,661, 7,114,753, 7,151,450, 7,578,097, 7,699,089,7,748,431, 7,757,437, 8,037,921, 8,167,020, 8,113,265.

RITE-HITE®, RITE-HITE® DOORS, RITE-HITE® MACHINE GUARDING, DEFENDER™, FLASHFOLD™, VERTIGUARD™,SLIDEAIR™, ROLLSHIELD™, ROLLTOP™, ROBOGUARD™ and XTEN™ are trademarks of RITE-HITE®.

RITE-HITE MACHINE GUARDING

4343 Chavenelle Drive

P.O. Box 1200

Dubuque, Iowa 52002-2654

Toll Free Sales: 800-553-5560

Sales: 563-589-4401

Sales Fax: 563-589-2776

Service: 563-589-2722

Service Fax: 563-589-2737

Representatives in All Major Cities

www.ritehite.com

AMEN00040 2018-06-28

RITE-HITE MACHINE GUARDING LIMITED WARRANTY


AMEN00040 2018-06-28

Documents

AUTOMATED ROLL-UP CURTAIN