Upload
abhijit-kumar-ghosh
View
190
Download
4
Tags:
Embed Size (px)
Citation preview
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 1
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
Agriculture, Forestry, Fishing and Food 1
101435 AS 1766.5 Food Microbiology, Method 5: Preparation of culture media, diluents and reagents
Standard Withdrawal 1 FT-035 AUS Project Setup
101422 AS 4276.14 Water microbiology – Salmonellae Standard Revision 1 FT-020 AUS Project Setup
101423 AS 4276.15 Water microbiology – Examination for Vibrio cholerae Standard Revision 1 FT-020 JNT Project Setup
101424 AS 4276.19 Examination for thermophilic Campylobacter spp. – Membrane filtration Standard Revision 1 FT-020 JNT Project Setup
101432 AS 5013.1 Food Microbiology, Method 1: Examination for specific organisms—Standard plate count
Standard Revision 1 FT-035 AUS Project Setup
101433 AS 5013.6 Food Microbiology, Method 6: Examination for specific organisms—Campylobacter
Standard Revision 1 FT-035 AUS Project Setup
101434 AS 5013.7 Food Microbiology, Method 7: Examination of specific products—Eggs and egg products
Standard Revision 1 FT-035 AUS Project Setup
101512 AS 6000-2009 Organics Standard Revised Text Amendment
1 FT-032 AUS Project Setup
101289 AS 6000-2009 Organic and Biodynamic Products Standard Revised Text Amendment
1 FT-032 AUS Public Commenting
100747 AS/NZS 3580.10.2 Ambient air – Particulate matter – Determination of impinged matter expressed as directional dirtiness, background dirtiness and/or area dirtiness (directional dust gauge method)
Standard Revision 1 EV-007 JNT Styling, Editing & Graphics – Public Comment
100745 AS/NZS 3580.13.2 Methods for sampling and analysis of ambient air – Determination of fluorides – Gaseous and acid-soluble particulate fluorides – Manual, double filter paper sampling
Standard Revision 1 EV-007 JNT Public Commenting
101437 AS/NZS 4659.1 Guide to determining the equivalence of food microbiology test methods – Qualitative tests
Standard Revision 1 FT-035 JNT Project Setup
101438 AS/NZS 4659.2 Guide to determining the equivalence of food microbiology test methods – Quantitative tests
Standard Revision 1 FT-035 JNT Project Setup
101439 AS/NZS 4659.3 Guide to determining the equivalence of food microbiology test methods – Confirmation tests
Standard Revision 1 FT-035 JNT Project Setup
101440 AS/NZS 4659.4 Guide to determining the equivalence of food microbiology test methods – Antibiotic tests
Standard Revision 1 FT-035 JNT Project Setup
101436 HB 224 Handbook for microbiological testing in food premises Handbook Withdrawal 1 FT-035 AUS Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 2
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100439 MP 100-2009 Procedures for certification of organic and biodynamic products Standard Revised Text Amendment
1 FT-032 AUS Public Commenting
Mining 2
101153 AS/NZS 4240.1 Remote Control Systems for mining equipment Standard Revision 2 EL-023 JNT Project Setup
101154 AS/NZS 1299 Electrical Equipment for Mines Flameproof Restrained Equip. Standard Revision 2 EL-023 JNT Project Setup
101155 AS/NZS 1300 Electrical Equipment for Mines Flameproof Bolted Equip. Standard Revision 2 EL-023 JNT Project Setup
101147 AS/NZS 1802 Electrical Equipment for Mines Reeling & Trailing Cables –coal Standard Revision 2 EL-023 JNT Project Setup
101149 AS/NZS 1972 Electrical Equipment for Mines Cables- non reeling / trailing Standard Revision 2 EL-023 JNT Project Setup
100478 AS/NZS 2290.1 Electrical equipment for coal mines – Introduction and maintenance – For hazardous areas
Standard Revision 2 EL-023 JNT Public Commenting
101034 AS/NZS 2290.3 Electrical equipment for coal mines – Maintenance and overhaul – Maintenance of gas detecting and monitoring equipment
Standard Revision 2 EL-023 JNT Drafting
101148 AS/NZS 2802 Electrical Equipment for Mines Reeling & Trailing Cables –non coal Standard Revision 2 EL-023 JNT Project Setup
100484 AS/NZS 3007 Electrical installations – Surface mines and associated processing plant – Scope and definitions
Standard Revision 2 EL-023 JNT Styling, Editing & Graphics – Public Comment
5544 AS/NZS 3785.6 Guides and rubbing ropes for conveyances Standard Revision 2 ME-018 JNT Drafting
100495 AS/NZS 3785.8 Underground mining – Shaft equipment – Personnel conveyances in other than vertical shafts
Standard Revision 2 ME-018 JNT Drafting
100475 AS/NZS 4240.3 Standards for Mining Electrical Equipment including hazardous areas equipment.
Standard Revision 2 EL-023 JNT Balloting
101035 AS/NZS 4641 Electrical apparatus for detection of oxygen and other gases and vapours at toxic levels – General requirements and test methods
Standard Revision 2 EL-023 JNT Drafting
100482 AS/NZS 4871.6 Earth-moving machinery and ancillary equipment for use in mines – Electrical wiring systems at extra-low voltage and AS/NZS 4871.6 Electrical equipment for coal mines, for use underground – Diesel powered machinery and ancillary equipment
Standard Revision 2 EL-023 JNT Public Commenting
100819 AS4024.3610 Safety of Machinery – Part 3610: Conveyors – General Safety Requirements
Standard New 2 SF-041 AUS Drafting
100820 AS4024.3611 Safety of machinery – Part 3611: Conveyors – Belt conveyors for bulk materials handling, travelling trippers and shuttle conveyors
Standard New 2 SF-041 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 3
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100823 AS4024.3612 Safety of machinery – - Part 3612: Conveyors – Light duty general purpose belt conveyors
Standard New 2 SF-041 AUS Drafting
100825 AS4024.3613 Safety of machinery – Part 3613: Conveyors – Screw conveyors Standard New 2 SF-041 AUS Drafting
100826 AS4024.3614 Safety of machinery – Part 3614: Conveyors – Chain conveyors Standard New 2 SF-041 AUS Drafting
100845 AS4024.3615 Safety of machinery – Part 3615: Conveyors – Mobile and transportable conveyors
Standard New 2 SF-041 AUS Drafting
101298 ASCRM 25-2 Manufacture and Certification of a replacement ASCRM for ASCRM025.
Reference Material New 2 MN-009 AUS Drafting
7456 ASCRM-027 Certified reference material – Alumina – XRF Elemental analysis Reference Material Other 2 MN-009 AUS Drafting
101156 HB 239 Handbook for Repair and Overhaul Handbook Revision 2 EL-023 JNT Project Setup
101152 HB 242 High Voltage Mining Equipment for use underground Handbook Revision 2 EL-023 AUS Project Setup
101150 HB XXX Mining Electrical Engineering Handbook Handbook New 2 EL-023 JNT Project Setup
101151 HB XXX Mining Electrical Protection Handbook Handbook New 2 EL-023 JNT Project Setup
101157 HB XXX Mining Electrical U/G Cable Management Handbook Handbook New 2 EL-023 JNT Project Setup
101158 HB XXX Mining Electrical Generators, Inverters & UPS Handbook Handbook New 2 EL-023 JNT Project Setup
7457 TR-027 Alumina – Preparation and certification of ASCRM 027 Technical Report Other 2 MN-009 AUS Publication
101383 TR2.25-2 Certified Reference Material – Alumina-Preparation & Certification of ASCRM 025-2
Reference Material New 2 MN-009 AUS Drafting
Manufacturing and Processing 3
100850 AS 1210 Pressure vessels Standard Revised Text Amendment
3 ME-001 AUS Public Commenting
101221 AS 1418.11 Cranes – Vehicle Loading Standard International Adoption – Modified
3 ME-005 AUS Drafting
8578 AS 1418.5 Cranes, hoists and winches Part 5: Mobile cranes Standard International Adoption – Modified
3 ME-005 AUS Styling, Editing & Graphics – Public Comment
101196 AS 1668.1 The use of mechanical ventilation and air-conditioning in buildings – Fire and smoke control
Standard Revision 3 ME-062 AUS Project Setup
101301 AS 2008 Residual bitumen for pavements Standard Revision 3 CH-025 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 4
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101583 AS 2030.5 Ruling to the Gas cylinders, Ruling 1: Filling, inspection and testing of refillable cylinders (Ruling to AS 2030.5-2009)
Ruling Other 3 ME-002 AUS Balloting
100756 AS 2321 Short-link chain for lifting purposes Standard Revision 3 ME-025 AUS Drafting
100794 AS 2473.2 Valves for compressed gas cylinders Part 2: Outlet connections (threaded) and stem (inlet) threads
Standard Revision 3 ME-002 AUS Drafting
101222 AS 2550.11 Cranes – Safety – Vehicle loading Standard Revision 3 ME-005 AUS Drafting
6155 AS 2550.15 Cranes, hoists and winches – Safe use, Part 15: Concrete placing equipment
Standard Revision 3 ME-005 AUS Public Commenting
101223 AS 2550.5 Cranes – Safety – Mobile cranes Standard Revision 3 ME-005 AUS Drafting
100990 AS 2832-1 Cathodic protection of metals, Part 1: Pipes and cables Standard Revision 3 MT-014 AUS Drafting
100854 AS 2941 Fixed fire protection installations – Pumpset systems Standard Revision 3 FP-008 AUS Public Commenting
100760 AS 3775.1 Chain slings – Grade T – Product specification Standard Revision 3 ME-025 AUS Drafting
100759 AS 3775.2 Chain slings – Grade T – Care and use Standard Revision 3 ME-025 AUS Drafting
100761 AS 3776 Lifting components for Grade T chain slings Standard Revision 3 ME-025 AUS Drafting
100421 AS 3920 Pressure Equipment – Conformity Assessment Standard Revision 3 ME-001 AUS Public Commenting
101164 AS 4024.1.1101 Update comprising 26 ISO/IEC/EN standards to latest versions of these standards i.e.:
Standard Revision 3 SF-041 AUS Project Setup
101165 AS 4024.1.1201 ISO 12100-1 Standard Revision 3 SF-041 AUS Project Setup
101166 AS 4024.1.1202 ISO 12100-2 Standard Revision 3 SF-041 AUS Project Setup
101167 AS 4024.1.1301 ISO 14121 Standard Revision 3 SF-041 AUS Project Setup
101168 AS 4024.1.1302 CEN 626-1 Standard Revision 3 SF-041 AUS Project Setup
101169 AS 4024.1.1401 CEN 614-1 Standard Revision 3 SF-041 AUS Project Setup
101170 AS 4024.1.1501 ISO 13849-1 Standard Revision 3 SF-041 AUS Project Setup
101172 AS 4024.1.1601 CEN 953 Standard Revision 3 SF-041 AUS Project Setup
101173 AS 4024.1.1602 ISO 14119 Standard Revision 3 SF-041 AUS Project Setup
101174 AS 4024.1.1603 CEN 1037 Standard Revision 3 SF-041 AUS Project Setup
101175 AS 4024.1.1604 ISO 13850 Standard Revision 3 SF-041 AUS Project Setup
101176 AS 4024.1.1701 ISO 7250-1 Standard Revision 3 SF-041 AUS Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 5
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101177 AS 4024.1.1702 CEN 547-1 Standard Revision 3 SF-041 AUS Project Setup
101178 AS 4024.1.1703 CEN 547-2 Standard Revision 3 SF-041 AUS Project Setup
101179 AS 4024.1.1704 CEN 547-3 Standard Revision 3 SF-041 AUS Project Setup
101180 AS 4024.1.1801 ISO 13852 Standard Revision 3 SF-041 AUS Project Setup
101181 AS 4024.1.1802 ISO 13853 Standard Revision 3 SF-041 AUS Project Setup
101182 AS 4024.1.1803 ISO 13854 Standard Revision 3 SF-041 AUS Project Setup
101183 AS 4024.1.1901 CEN 894-1 Standard Revision 3 SF-041 AUS Project Setup
101184 AS 4024.1.1902 CEN 894-2 Standard Revision 3 SF-041 AUS Project Setup
101185 AS 4024.1.1903 CEN 894-3 Standard Revision 3 SF-041 AUS Project Setup
101186 AS 4024.1.1904 IEC 61310-1 Standard Revision 3 SF-041 AUS Project Setup
101187 AS 4024.1.1905 IEC 61310-2 Standard Revision 3 SF-041 AUS Project Setup
101188 AS 4024.1.1906 IEC 61310-3 Standard Revision 3 SF-041 AUS Project Setup
101189 AS 4024.1.1907 CEN 981 Standard Revision 3 SF-041 AUS Project Setup
101171 AS 4204.1.1502 ISO 13849-2 Standard Revision 3 SF-041 AUS Project Setup
101210 AS 4324 Mobile equipment for continuous handling of bulk materials – General requirements for the design of steel structures.
Standard New 3 ME-043 AUS Drafting
100852 AS 4343 Pressure equipment – Hazard levels Standard Revision 3 ME-001 AUS Drafting
101234 AS 4484 Gas Cylinders for Industrial, scientific, medical and refrigerant use – Labelling and colour coding information
Standard Revision 3 ME-002 AUS Drafting
100732 AS 4747.6 Meters for non-urban water supply – Installation and commissioning of open channel meters
Standard New 3 CE-024 AUS Publication
101291 AS/NZS 1163 Cold-formed structural steel hollow sections Standard Revision 3 BD-023 JNT Drafting
100851 AS/NZS 1200 Pressure equipment Standard Revision 3 ME-001 JNT Drafting
101345 AS/NZS 1301.206S Methods of test for pulp and paper – Freeness of pulp Standard Revision 3 PK-019 JNT Project Setup
101346 AS/NZS 1301.417S Methods of test for pulp and paper – Sampling of paper, paperboard and pulp for testing.
Standard Revision 3 PK-019 JNT Project Setup
101347 AS/NZS 1301.418S Methods of test for pulp and paper – Ash content of wood- pulp- paper and board
Standard Revision 3 PK-019 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 6
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101348 AS/NZS 1301.426S Methods of test for pulp and paper – Determination of thickness and apparent bulk density or apparent sheet density
Standard Revision 3 PK-019 JNT Project Setup
101349 AS/NZS 1301.436S Methods of test for pulp and paper – Measurement of diffuse reflectance factor
Standard Revision 3 PK-019 JNT Project Setup
101350 AS/NZS 1301.455S Methods of test for pulp and paper – Colour measurement with a diff/0 degrees geometry tristimulus reflectometer
Standard Revision 3 PK-019 JNT Project Setup
101516 AS/NZS 1365 Tolerances for flat-rolled steel products Standard Revised Text Amendment
3 MT-001 JNT Project Setup
101006 AS/NZS 1554.1 Structural steel welding – Welding of steel structures Standard Revision 3 WD-003 JNT Public Commenting
101007 AS/NZS 1554.3 Structural steel welding – Welding of reinforcing steel Standard Revision 3 WD-003 JNT Public Commenting
101008 AS/NZS 1554.4 Structural steel welding – Welding of high strength quenched tempered steels
Standard Revision 3 WD-003 JNT Public Commenting
101009 AS/NZS 1554.5 Structural steel welding – Welding of steel structures subject to high levels of fatigue loading
Standard Revision 3 WD-003 JNT Public Commenting
101010 AS/NZS 1554.7 Structural steel welding – Welding of sheet steel structures Standard Revision 3 WD-003 JNT Public Commenting
101510 AS/NZS 1595 Cold-rolled, unalloyed steel sheet and strip Standard Revised Text Amendment
3 MT-001 JNT Project Setup
101012 AS/NZS 16834 Welding consumables – Wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels – Classification
Standard International Adoption – Modified
3 WD-002 JNT Publication
101344 AS/NZS 1906.1 Retroreflective materials and devices for road traffic control purposes – Retroreflective materials
Standard Revised Text Amendment
3 MS-049 JNT Public Commenting
8203 AS/NZS 2208 Safety glazing materials in buildings Standard Revision 3 BD-007 JNT Public Commenting
100996 AS/NZS 2312-1 Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings
Standard Revision 3 MT-014 JNT Drafting
101413 AS/NZS 2312-2 Guidelines and recommendations for the protection against corrosion of iron and steel in structures —Part 1:General principles of design and corrosion resistance
Standard Revision 3 MT-014 JNT Drafting
101414 AS/NZS 2312-3 Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 2:Hot dip galvanizing
Standard Revision 3 MT-014 JNT Drafting
100926 AS/NZS 2891.1.1 Methods of sampling and testing asphalt – Sampling – Loose asphalt Standard Revision 3 CE-006 JNT Public Commenting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 7
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100107 AS/NZS 3566.2 Self-drilling screws for the building and construction industries – Corrosion resistance requirements and requirements for non-conductive seals
Standard Revision 3 ME-029 JNT Balloting
101292 AS/NZS 3678 Structural steel – Hot–rolled plates, floorplates and slabs Standard Revision 3 BD-023 JNT Drafting
101293 AS/NZS 3679.1 Structural steel – Hot-rolled bars and sections Standard Revision 3 BD-023 JNT Drafting
101294 AS/NZS 3679.2 Structural Steel – Welded I Sections Standard Revision 3 BD-023 JNT Drafting
100853 AS/NZS 3992 Pressure equipment – Welding and brazing qualification Standard Revision 3 ME-001 JNT Drafting
101200 AS/NZS 4200.1 Pliable building membranes and underlays – Part 1:Materials Standard Revision 3 BD-058 JNT Project Setup
101068 AS/NZS 4233-1 High pressure water (hydro) jetting systems; Part 1 Guidelines for safe operation and maintenance
Standard Revision 3 SF-043 JNT Drafting
101069 AS/NZS 4233-2 High pressure water (hydro) jetting systems; Part 2 Construction and Performance
Standard Revision 3 SF-043 JNT Drafting
101427 AS/NZS 4399 Sun Protective Clothing: Evaluation and classification Standard Revision 3 TX-021 JNT Project Setup
101201 AS/NZS 4859.1 Materials for the thermal insulation of buildings – General criteria and technical provisions
Standard Revision 3 BD-058 JNT Project Setup
100985 AS/NZS 5532 Industrial Fall Arrest Systems and Devices – Single Point Anchor Devices
Standard New 3 SF-015 JNT Public Commenting
101371 AS/NZS 7671-2010 Plastics piping system for soil and waste discharge (low and high) temperature) inside buildings – Polypropylene (PP) (ISO 7671:2003, MOD)
Standard Revised Text Amendment
3 PL-006 JNT Balloting
101299 AS/NZS ISO 12759 Fans – Efficiency classification for fans Standard International Adoption – Identical
3 ME-013 AUS Balloting
101014 AS/NZS ISO 14171 Welding consumables – Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of non alloy and fine grain steels -Classification
Standard International Adoption – Identical
3 WD-002 JNT Publication
101016 AS/NZS ISO 24598 Welding consumables – Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of creep-resisting steels – Classification
Standard International Adoption – Identical
3 WD-002 JNT Publication
101017 AS/NZS ISO 26304 Welding consumables – Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of high strength steels – Classification
Standard International Adoption – Identical
3 WD-002 JNT Publication
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 8
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100738 AS/NZS ISO 5149.2 Design, construction, testing, marking and documentation Standard International Adoption – Modified
3 ME-006 JNT Drafting
100739 AS/NZS ISO 5149.3 Installation Site Standard International Adoption – Modified
3 ME-006 JNT Drafting
100740 AS/NZS ISO 5149.4 Operation, maintenance, repair and recovery Standard International Adoption – Modified
3 ME-006 JNT Drafting
101587 Rul CR.1—2012 Ruling 1: Load testing (commissioning tests) of bridge, gantry, portal (including container cranes) and jib cranes (Ruling to AS 1418.3—1997)
Ruling New 3 ME-005 AUS Project Setup
Building and Construction 4
100716 AS 1141.24 Standard durability by exposure to sodium sulphate Standard Revision 4 CE-012 AUS Publication
100718 AS 1141.60.1 Accelerated mortar bar test for assessment of alkali silica reaction in concrete aggregate
Standard New 4 CE-012 AUS Drafting
100719 AS 1141.60.2 Concrete prism test for assessment of alkali silica reaction in concrete aggregate
Standard New 4 CE-012 AUS Drafting
100798 AS 12239 Smoke alarms using scattered light, transmitted light or ionization Standard Revision 4 FP-002 AUS Drafting
101057 AS 1445 Hot-dipped zinc-coated or aluminium/zinc-coated steel sheet – 76 mm pitch corrugated
Standard Revision 4 MT-009 AUS Publication
101002 AS 1540.4 Methods for fire tests on building materials, components and structures, Part 4: Fire-resistance test of elements of construction
Standard Revision 4 FP-018 AUS Public Commenting
100235 AS 1597.2 Precast reinforced concrete box culverts: Part 2 Large culverts Standard Revision 4 CE-026 AUS Styling, Editing & Graphics – Public Comment
1488 AS 1657 Fixed platforms, walkways, stairways and ladders – Design, construction and installation Part 1: Requirements for general applications
Standard Revision 4 SF-013 AUS Public Commenting
101513 AS 1905.1 Components for the protection of openings in fire-resistant walls, Part 1 : Fire Resistant Doorsets
Standard Revision 4 FP-019 AUS Project Setup
5525 AS 2047 External Windows and Doors In Buildings – Performance Specifications Standard Revision 4 BD-021 AUS Drafting
100764 AS 2118.1 Automatic fire sprinkler systems Standard Revision 4 FP-004 AUS Drafting
101590 AS 2118.4 Automatic fire sprinkler systems – Part 4: Sprinkler protection for accommodation buildings not exceeding four storeys in height
Standard Correction Amendment
4 FP-004 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 9
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101003 AS 2124 General conditions of contract Standard Revision 4 MB-010 AUS Project Setup
8597 AS 2419.1 Fire Hydrants -System Design & Installations Standard Revision 4 FP-009 AUS Public Commenting
100720 AS 2758.1 Aggregate and rock for engineering purposes – Part 1 Concrete Aggregate
Standard Revision 4 CE-012 AUS Drafting
101415 AS 3600 2009 Concrete structures Standard Correction Amendment
4 BD-002 AUS Styling, Editing & Graphics – Public Comment
4754 AS 3600 Commentary Concrete Structures – Supplement Commentary Revision 4 BD-002 AUS Styling, Editing & Graphics – Public Comment
100836 AS 3660.1 Termite management – New building work Standard Revision 4 BD-074 AUS Styling, Editing & Graphics – Public Comment
100838 AS 3660.3 Termite management – Assessment criteria for termite management systems
Standard Revision 4 BD-074 AUS Drafting
100464 AS 3706.5 Geotextiles – Methods of test – Determination of puncture resistance – Drop cone method
Standard Revision 4 CE-020 AUS Balloting
100466 AS 3706.7 Geotextiles – Methods of test – Determination of pore-size distribution – Dry-sieving method
Standard Revision 4 CE-020 AUS Balloting
101426 AS 3745 Planning for emergencies in facilities Standard Revised Text Amendment
4 FP-017 AUS Project Setup
100430 AS 3850.1 Precast and Tilt-Up Concrete Elements in Building Construction – part 1 General Requirements
Standard Revision 4 BD-066 AUS Drafting
100664 AS 3850.2 Precast and Tilt-Up Concerete Elements in Building Construction – Part 2 Precast and Tilt-up Concrete Panels
Standard Revision 4 BD-066 AUS Drafting
100322 AS 3999-1992 Thermal insulation of dwellings – Bulk insulation – Installation requirements
Standard Revision 4 BD-058 AUS Drafting
101286 AS 4133.4.2.2 Methods of testing rocks for engineering purposes-Rock strength tests—Determination of uniaxial compressive strength-Rock strength less than 50 Mpa
Standard New 4 CE-009 AUS Drafting
101287 AS 4133.4.3.2 Methods of testing rocks for engineering purposes- Rock strength tests—Determination of the deformability of rock materials in uniaxial compressions—Rock strength less than 50 Mpa
Standard New 4 CE-009 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 10
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
8112 AS 4586 Slip resistance of new pedestrian surface material Standard Revision 4 BD-094 AUS Public Commenting
8113 AS 4663 Slip resistance measurement in existing pedestrian surfaces Standard Revision 4 BD-094 AUS Public Commenting
100292 AS 5100.1 Bridge Design – Scope and General Principles Standard Revision 4 BD-090 AUS Drafting
100693 AS 5100.1 Supp 1 Bridge design – Scope and general principles – Commentary (Supplement to AS5100.1 – 2004)
Supplement Revision 4 BD-090 AUS Drafting
100297 AS 5100.2 Bridge Design – Design Loads Standard Revision 4 BD-090 AUS Drafting
100694 AS 5100.2 Supp 1 Bridge design – Design loads – Commentary (Supplement to AS 5100.2 2004)
Supplement Revision 4 BD-090 AUS Drafting
100293 AS 5100.3 Bridge Design – Foundations and soil supporting structures Standard Revision 4 BD-090 AUS Balloting
100695 AS 5100.3 Supp 1 Bridge design – Foundations and soil supporting structures (Supplement to AS 5100.3)
Supplement Revision 4 BD-090 AUS Drafting
100295 AS 5100.4 Bridge Design – Bearing and Deck Joints Standard Revision 4 BD-090 AUS Drafting
100696 AS 5100.4 Supp 1 Bridge design – Bearings and deck joints – Commentary (Supplement to AS 5100.4 – 2004)
Supplement Revision 4 BD-090 AUS Drafting
100298 AS 5100.5 Bridge Design – Concrete Standard Revision 4 BD-090 AUS Drafting
100700 AS 5100.5 Supp 1 Bridge design – Concrete Supplement Revision 4 BD-090 AUS Drafting
100294 AS 5100.7 Bridge Design – Rating of existing Bridges Standard Revision 4 BD-090 AUS Drafting
100698 AS 5100.7 Supp 1 Bridge design – Rating of existing bridges – Commentary (Supplement to AS 5100.7 – 2004)
Supplement Revision 4 BD-090 AUS Drafting
101232 AS 5100.8 Bridge Design, Part 8: Rehabilitation of bridges Standard New 4 BD-090 AUS Drafting
101266 AS 5100.8 Supp 1 Bridge Design Standard New 4 BD-090 AUS Drafting
101204 AS 5100.9 Bridge Design, Part 9: Timber Standard New 4 BD-090 AUS Drafting
101209 AS 5100.9 Bridge Design – Timber – Commentary Standard New 4 BD-090 AUS Drafting
100286 AS 5334 New Australian Standard – Principle Based Climate Change Adaptation – Requirements for Settlements and Infrastructure
Standard New 4 BD-103 AUS Balloting
101255 AS ISO 10545.16 (Identical) Ceramic tiles – Methods of test – Part 16 Small colour differences Standard International Adoption – Identical
4 BD-044 AUS Balloting
101254 AS ISO 10545.6 (Identical) Ceramic tiles – Methods of test – Part 6 Resistance to deep abrasion Standard International Adoption – Identical
4 BD-044 AUS Balloting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 11
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101514 AS ISO 13006 (Identical) Ceramic tiles – Definitions, classification, characteristics and marking Standard International Adoption – Identical
4 BD-044 AUS Public Commenting
101250 AS ISO 13007.1 (Identical) Ceramic tiles – Grouts and adhesives – Part 1 Standard International Adoption – Identical
4 BD-044 AUS Balloting
101251 AS ISO 13007.2 (Identical) Ceramic tiles – Grouts and adhesives – Part 2 Standard International Adoption – Identical
4 BD-044 AUS Balloting
101252 AS ISO 13007.3 (Identical) Ceramic tiles – Grouts and adhesives – Part 3 Standard International Adoption – Identical
4 BD-044 AUS Balloting
101253 AS ISO 13007.4 (Identical) Ceramic tiles – Grouts and adhesives – Part 4 Standard International Adoption – Identical
4 BD-044 AUS Balloting
100299 AS/NZS 1576.3 Scaffolding – Prefabricated and tube-and-coupler scaffolding Standard Revision 4 BD-036 JNT Public Commenting
100300 AS/NZS 1576.4 Scaffolding – Suspended scaffolding Standard Revision 4 BD-036 JNT Balloting
101143 AS/NZS 1577 Scaffold Decking Components Standard Revision 4 BD-036 JNT Public Commenting
101144 AS/NZS 2179.1 Specifications for rainwater goods, accessories and fasteners – Metal shape or sheet rainwater goods, and metal accessories and fasteners
Standard Revision 4 WS-014 JNT Public Commenting
100994 AS/NZS 2327.1 Simply supported beams Standard Revision 4 BD-032 JNT Project Setup
100991 AS/NZS 2327.2 Continuous composite beams Standard New 4 BD-032 JNT Project Setup
100992 AS/NZS 2327.3 Composite columns Standard New 4 BD-032 JNT Project Setup
100993 AS/NZS 2327.4 Composite slabs Standard New 4 BD-032 JNT Project Setup
101058 AS/NZS 2728 Prefinished/prepainted sheet metal products for interior/exterior building applications – Performance requirements
Standard Revision 4 MT-009 JNT Publication
100934 AS/NZS 2891.13.1 Methods of sampling and testing asphalt- Determination of the resilient modulus pof asphalt- Indirect tensile method
Standard Revision 4 CE-006 JNT Styling, Editing & Graphics – Public Comment
100935 AS/NZS 2891.14.1.1 Methods of sampling and testing asphal;t- Field density tests- Determination of field density of compacted asphalt using a nuclear surface moisture-density gauge- Direct transmission mode
Standard Revision 4 CE-006 JNT Balloting
100936 AS/NZS 2891.14.1.2 Methods of sampling and testing asphalt- Field density tests- Determination of field density of compacted asphalt using a nuclear surface moisture-density gauge- Backscatter mode
Standard Revision 4 CE-006 JNT Balloting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 12
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100937 AS/NZS 2891.14.2 Methods of sampling and testing asphalt – Field density tests- Determination of field density of compacted asphalt using a nuclear thin-layer density gauge
Standard Revision 4 CE-006 JNT Balloting
100938 AS/NZS 2891.14.3 Methods of sampling and testing asphalt- Field density tests- calibration of nuclear-thin layer density gauge using standard blocks
Standard Revision 4 CE-006 JNT Balloting
100939 AS/NZS 2891.14.4 Methods of sampling and testing asphalt- Field density tests- Calibration of nuclear surface moisture density gauge- Backscatter mode
Standard Revision 4 CE-006 JNT Publication
100929 AS/NZS 2891.2.2 Methods of samplinbg and testing asphalt- Sample preparation- Compaction of asphalt test specimens using a gyratory compactor
Standard Revision 4 CE-006 JNT Drafting
100930 AS/NZS 2891.3.1 Methods of sampling ans testing asphalt- Bitumen content and aggregate grading- Centrifugal extraction method
Standard Revision 4 CE-006 JNT Styling, Editing & Graphics – Public Comment
100931 AS/NZS 2891.3.2 Methods of sampling and testing asphalt- Bitumen content and aggregate grading- centrifugal extraction method
Standard Revision 4 CE-006 JNT Styling, Editing & Graphics – Public Comment
100932 AS/NZS 2891.3.3 Methods of sampling and testing asphalt-Bitumen content and aggregate grading – Pressure filter method
Standard Revision 4 CE-006 JNT Public Commenting
101133 AS/NZS 2904 Damp-proof courses and flashings Standard Revised Text Amendment
4 BD-029 JNT Publication
100753 AS/NZS 2941 Condensed Aerosol Fire Extinguishing Systems Standard Revision 4 FP-011 JNT Public Commenting
100814 AS/NZS 4200-2 Pliable building membranes and underlays – Part 2: Installation requirements
Standard Revision 4 BD-058 JNT Drafting
100840 AS/NZS 4386-1 Domestic kitchen assemblies – Kitchen units Standard Revision 4 BD-089 JNT Project Setup
100841 AS/NZS 4386-2 Domestic kitchen assemblies – Installation Standard Revision 4 BD-089 JNT Project Setup
101475 AS/NZS 4389 Safety Mesh Standard Revision 4 PL-022 JNT Project Setup
100274 AS/NZS 4505 Domestic Garage Doors Standard Revision 4 BD-014 JNT Balloting
100296 AS/NZS 5100.6 Bridge Design – Steel and Composite Construction Standard Revision 4 BD-090 JNT Drafting
100697 AS/NZS 5100.6 Supp1 Bridge design – Steel and composite construction – Commentary (Supplement to AS 5100-6 – 2004)
Supplement Revision 4 BD-090 JNT Drafting
100770 AS/NZS 8008 Finger-jointed structural timber Standard New 4 TM-004 JNT Public Commenting
101302 AS2890.3 Parking facilities – Bicycle parking facilities Standard Revision 4 CE-001 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 13
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100259 ATS 5200.505 Multilayer Piping systems for hot and cold water insatllations inside buildings – Polypropoylene (PP) pipes – PP-H, PP-B, PP-R, PP-RCT
Technical Spec New 4 WS-031 AUS Public Commenting
101586 Rul PP.1—2012 Ruling 2: When a booster assembly is required (Ruling to AS 2419.1—2005)
Ruling New 4 FP-009 AUS Project Setup
100389 TBA Design for access and mobility – Adaptable Housing Standard Revision 4 ME-064 AUS Drafting
100391 TBA Design for access and mobility – Wayfinding Standard Revision 4 ME-064 AUS Drafting
100392 TBA Design for access and mobility – Enhanced and additional requirements – Buildings and facilities
Standard Revision 4 ME-064 AUS Drafting
100709 xxxx Development of a Standard for the Determination of Group numbers for wall and ceiling linings materials
Standard New 4 FP-018 AUS Drafting
Energy 5
100802 AS 1056.1 Storage water heaters – General requirements Standard Revision 5 EL-020 AUS Drafting
101375 AS 1172.1 Water closets (WC) – Pans Standard Revision 5 WS-003 AUS Public Commenting
101376 AS 1172.2 Water closet (WC) pans of 6/3 L capacity or proven equivalent – Cisterns
Standard Revision 5 WS-003 AUS Public Commenting
101142 AS 1731.14 Refrigerated display cabinets – Minimum energy performance Standard (MEPS) requirements
Standard Revision 5 ME-008 AUS Project Setup
101449 AS 1798 Lighting poles and bracket arms – Preferred dimensions Standard New 5 LG-002 AUS Project Setup
100817 AS 2067 Substations and HV Installations greater than 1kV ac Standard Revision 5 EL-043 AUS Drafting
101257 AS 2658 LP Gas – Portable and mobile appliances; amendment 2012 Standard Revised Text Amendment
5 AG-001 AUS Balloting
100788 AS 3814 Industrial and commercial gas-fired appliances Standard Revision 5 AG-011 AUS Drafting
100386 AS 4777.1 Grid connection of energy systems via inverters – installation requirements
Standard Revision 5 EL-042 JNT Drafting
100387 AS 4777.2 Grid connection of energy systems via inverters – inverter and grid connection requirements
Standard Revision 5 EL-042 JNT Drafting
100217 AS 5263 Gas Appliance Standards – Part 0 Safety Requirements Standard New 5 AG-001 AUS Public Commenting
100328 AS 5389 (Int) Solar thermal cooling systems – Energy rating and testing for performance
Interim Standard New 5 CS-028 AUS Styling, Editing & Graphics – Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 14
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100687 AS 5577 Australian Standard for Energy Safety Systems (ENSS) for the electricity supply industry (ESI)
Standard New 5 EN-004 AUS Balloting
100907 AS 8800.1 Installation of ground source heat pump systems – Part 1: System design
Standard New 5 EN-005 AUS Drafting
101233 AS IEC 61400.2 Wind turbines Part 2: Design requirements for small wind turbines Standard International Adoption – Identical
5 EL-048 AUS Balloting
101272 AS IEC 61800.5.1 IEC 61800-5-1 Ed. 2.0 Adjustable speed electrical power drive systems – Part 5-1: Safety requirements – Electrical, thermal and energy
Standard New 5 EL-027 AUS Publication
101273 AS IEC 61800.5.2 Adjustable speed electrical power drive systems – Part 5-2: Safety requirements – Functional
Standard New 5 EL-027 AUS Publication
101404 AS NZS 5033 AMDT 1 Installation and safety requirements for photovoltaic (PV) arrays Standard Correction Amendment
5 EL-042 JNT Styling, Editing & Graphics – Drafting
101443 AS/NZS 1158.0 Consequential changes to definitions due to SSL and Induction lamp inclusion
Standard Revision 5 LG-002 JNT Project Setup
101442 AS/NZS 1158.1.1 Lighting for roads and public spaces Standard Revision 5 LG-002 JNT Project Setup
101444 AS/NZS 1158.1.2 Include SSL sources and induction lamps Standard Revision 5 LG-002 JNT Project Setup
101190 AS/NZS 1158.2 Lighting for roads and public spaces – Computer procedures for the calculation of light technical parameters for Category V and Category P lighting
Standard Revision 5 LG-002 JNT Project Setup
101445 AS/NZS 1158.3.1 Lifetime and Maintenance factors Standard Revision 5 LG-002 JNT Project Setup
101446 AS/NZS 1158.3.2 Pedestrian Area (Category P) lighting – Guide to design, installation, operation and maintenance
Standard New 5 LG-002 JNT Project Setup
101447 AS/NZS 1158.4 Glare, visibility for turning traffic, ambiguous Figure, consider signalised crossing
Standard Revision 5 LG-002 JNT Project Setup
101448 AS/NZS 1158.5 Include daylight assessment, specific situation analysis, wall maintenance factor
Standard Revision 5 LG-002 JNT Project Setup
101191 AS/NZS 1158.6 Lighting for roads and public spaces – Luminaires Standard Revision 5 LG-002 JNT Drafting
100880 AS/NZS 1596 The storage and handling of LP Gas Standard Revision 5 ME-015 JNT Public Commenting
100502 AS/NZS 1768 Lightning protection Standard Revision 5 EL-024 JNT Drafting
100925 AS/NZS 2053.1 Conduit systems for cable management – Part 1: General requirements Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 15
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100927 AS/NZS 2053.21 Conduit systems for cable management- Part 21: Particular requirements- Rigid conduit systems
Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
100928 AS/NZS 2053.22 Conduit systems for cable management- Part 22: Particular requirements- Pliable conduit systems
Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
101270 AS/NZS 3004.1 Electrical installations—Marinas, recreational and other boats – Part 1, Marinas
Standard Revision 5 EL-057 JNT Drafting
101271 AS/NZS 3004.2 Electrical installations—Marinas and recreational boats, Part 2: Recreational boats installations
Standard Revision 5 EL-057 JNT Drafting
100388 AS/NZS 3010 Electrical installations – Generating sets Standard Revision 5 EL-001 JNT Drafting
101396 AS/NZS 3012 Electrical Installations- Construction and Demolition Sites Standard Correction Amendment
5 EL-001 JNT Styling, Editing & Graphics – Public Comment
7731 AS/NZS 3018 Electrical installations – Domestic installations Standard Revision 5 EL-001 JNT Public Commenting
101579 AS/NZS 3112 Plugs and Sockets Standard Revised Text Amendment
5 EL-004 JNT Project Setup
101509 AS/NZS 3133 Approval and test specification—Air-break switches Standard Revision 5 EL-004 JNT Project Setup
100816 AS/NZS 3580.11.1 Methods for sampling and analysis of ambient air – Determination of volatile organic compounds – Methane and non-methane volatile organic compounds – Direct-reading instrumental method
Standard Revision 5 EV-007 JNT Styling, Editing & Graphics – Public Comment
100815 AS/NZS 3580.9.12 Methods for sampling and analysis of ambient air Method -Determination of suspended particulate matter—Methods for sampling and analysis of ambient air – Determination of suspended particulate matter – beta attenuation monitor (BAM)
Standard New 5 EV-007 JNT Styling, Editing & Graphics – Public Comment
101138 AS/NZS 3580.9.13 Methods for sampling and analysis of ambient air – Determination of suspended particulate matter – tapered element oscillating microbalance (TEOM)
Standard New 5 EV-007 JNT Styling, Editing & Graphics – Public Comment
101139 AS/NZS 3580.9.14 Methods for sampling and analysis of ambient air – Determination of suspended particulate matter – High volume sampler (HVS)
Standard New 5 EV-007 JNT Public Commenting
101036 AS/NZS 3598.0 Energy Audits Standard Revision 5 EN-001 JNT Drafting
101038 AS/NZS 3598.1 Energy Reviews – Commercial Standard New 5 EN-001 JNT Drafting
101037 AS/NZS 3598.1 Energy Reviews – Industry Standard New 5 EN-001 JNT Project Setup
101039 AS/NZS 3598.3 Energy Reviews – Transport Standard New 5 EN-001 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 16
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101381 AS/NZS 3662 Performance of showers for bathing Standard Revision 5 WS-038 JNT Public Commenting
101584 AS/NZS 3823.2 Performance of electrical appliances – Air conditioners and heat pumps. Part 2: Energy labelling and minimum energy performance standards (MEPS) requirements
Standard Revision 5 EL-056 JNT Public Commenting
101408 AS/NZS 4417.1:2012 A1 Regulatory compliance mark for electrical and electronic equipment – Part 1: Use of the mark
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101521 AS/NZS 4676 Structural design requirements for utility services poles Standard Revision 5 CE-019 JNT Project Setup
100801 AS/NZS 4692.1 Electric water heaters – Energy consumption, performance and general requirements
Standard Revised Text Amendment
5 EL-020 JNT Drafting
100713 AS/NZS 4755.3.3 Interaction of demand response enabling devices and electrical products – Part 3.3 Operational instructions and connections for electric and electric-boosted water heaters
Standard Revision 5 EL-054 JNT Project Approval
100714 AS/NZS 4755.3.4 Interaction of demand response enabling devices and electrical products – Part 3.4 Operational instructions and connections charge/discharge controllers for electric vehicles and other energy storage devices
Standard Revision 5 EL-054 JNT Project Approval
101421 AS/NZS 5033 Installation and safety requirements for photvoltaic (PV) arrays Standard Revision 5 EL-042 JNT Project Setup
100830 AS/NZS 5110 AMDT 1 Recessed luminaire barriers Standard Revised Text Amendment
5 EL-041 JNT Publication
100746 AS/NZS 5601.1 Gas Installations – Part 1 – General Installations Standard Revision 5 AG-006 JNT Public Commenting
100748 AS/NZS 5601.2 Gas installations – Part 2 – LP Gas installations in caravans and boats for non-propulsive purposes
Standard Revision 5 AG-006 JNT Public Commenting
100964 AS/NZS 5815.2 Information technology equipment – Energy performance of computer monitors, Part 2: Minimum Energy Performance Standards (MEPS)
Standard New 5 TE-021 JNT Publication
100805 AS/NZS 60076.2 Power transformers – Part 2: Temperature rise for liquid-immersed transformers
Standard Revision 5 EL-008 JNT Drafting
100806 AS/NZS 60076.6 Power transformers – Part 6: Reactors Standard Revision 5 EL-008 JNT Drafting
100804 AS/NZS 60076.7 Power Transformers- Part 7: Loading guide for oil-immersed power transformers
Standard Revision 5 EL-008 JNT Drafting
7918 AS/NZS 60076.99 Power transformers, Part 99: Minimum Energy Performance Standard (MEPS) requirements for distribution transformers
Standard New 5 EL-008 JNT Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 17
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101560 AS/NZS 60079-2 Explosive atmospheres – Part 2: Equipment protection by pressurized enclosures "p"
Standard International Adoption – Identical
5 EL-014 JNT Project Setup
101397 AS/NZS 60335.2.24:2010 A1 Household and similar electrical appliances – Safety – Part 2.24: Particular requirements for refrigerating appliances, ice-cream appliances and ice-makers
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101400 AS/NZS 60335.2.34:2013 Household and similar electrical appliances – Safety – Part 2.34: Particular requirements for motor-compressors
Standard Revision 5 EL-002 JNT Public Commenting
101401 AS/NZS 60335.2.67:2013 Household and similar electrical appliances – Safety – Part 2.67: Particular requirements for floor treatment machines, for commercial use
Standard Revision 5 EL-002 JNT Public Commenting
101402 AS/NZS 60335.2.68:2013 Household and similar electrical appliances – Safety – Part 2.68: Particular requirements for spray extraction machines, for commercial use
Standard Revision 5 EL-002 JNT Public Commenting
101409 AS/NZS 60335.2.71:2002 A2 Household and similar electrical appliances – Safety – Part 2.71: Particular requirements for electrical heating appliances for breeding and rearing animals
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101403 AS/NZS 60335.2.72:2013 Household and similar electrical appliances – Safety – Part 2.72: Particular requirements for floor treatment machines with or without traction drive, for commercial use
Standard Revision 5 EL-002 JNT Public Commenting
101410 AS/NZS 60335.2.86:2002 A4 Household and similar electrical appliances – Safety – Part 2.86: Particular requirements for electric fishing machines
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101411 AS/NZS 60335.2.87:2002 A2 Household and similar electrical appliances – Safety – Part 2.87: Particular requirements for electric animal-stunning equipment
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101398 AS/NZS 60335.2.89:2010 A1 Household and similar electrical appliances – Safety – Part 2.89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
100680 AS/NZS 60335.2.90:2006 A2 Household and similar electrical appliances – Safety – Part 2.90: Particular requirements for commercial microwave ovens
Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
101161 AS/NZS 60669.1 Switches for household and similar fixed-electrical installations – Part 1: General requirements
Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
101162 AS/NZS 60669.2.1 Switches for household and similar fixed-electtrical installations – Part 2.1: Particular requirements – Electrical swithes
Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
101399 AS/NZS 60745.2.3:2011 A1 Hand-held Motor-operated Electric Tools – Safety – Standard Revised Text Amendment
5 EL-002 JNT Public Commenting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 18
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100894 AS/NZS 60884.1 Plugs and socket-outlets for household and similar electrical appliances – Part 1: General requirements
Standard International Adoption – Modified
5 EL-004 JNT Public Commenting
101214 AS/NZS 61000.3.2 Electromagnetic compatibility (EMC)- Limits – Limits for harmonic current emissions (equipment input current <= 16 A per phase)
Standard Revision 5 EL-034 JNT Drafting
101470 AS/NZS 61439.4 Low-voltage switchgear and controlgear assemblies – Part 4: Particular requirements for assemblies for construction sites
Standard International Adoption – Modified
5 EL-006 JNT Project Setup
100855 AS/NZS 7000 Overhead line design – Detailed Procedures Standard Revised Text Amendment
5 EL-052 JNT Public Commenting
100827 AS/NZS IEC 60598.2.12 Luminaires – Part 2.12: Particular requirements – Mains socket-outlet mounted nightlights
Standard International Adoption – Modified
5 EL-041 JNT Public Commenting
101217 AS/NZS IEC 61000.3.12 Electromagnetic compatibility (EMC) – Part 3-12: Limits – Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and ≤ 75 A per phase
Standard Revision 5 EL-034 JNT Drafting
100828 AS/NZS IEC 61347.2.13 Lamp controlgear – Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
Standard International Adoption – Modified
5 EL-041 JNT Public Commenting
100829 AS/NZS IEC 62560 Self-ballasted LED lamps for general lighting services by voltage >50 V – Safety specifications
Standard International Adoption – Modified
5 EL-041 JNT Drafting
101466 AS/NZS IEC TR 61439-0 Low-voltage switchgear and controlgear assemblies – Part 0: Guide to specifying assemblies
Standard New 5 EL-006 JNT Project Setup
101467 AS/NZS IEC TR 61439-1 Low-voltage switchgear and controlgear assemblies – Part 1: General Rules
Standard New 5 EL-006 JNT Project Setup
101468 AS/NZS IEC TR 61439-2 Low-voltage switchgear and controlgear assemblies – Part 2: Power switchgear and controlgear assemblies
Standard New 5 EL-006 JNT Project Setup
101469 AS/NZS IEC TR 61439-3 Low-voltage switchgear and controlgear assemblies – Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
Standard New 5 EL-006 JNT Project Setup
101471 AS/NZS IEC TR 61439-5 Low-voltage switchgear and controlgear assemblies – Part 5: Assemblies for power distribution in public networks
Standard New 5 EL-006 JNT Project Setup
101472 AS/NZS IEC TR 61439-6 Low-voltage switchgear and controlgear assemblies – Part 6: Busbar trunking systems (busways)
Standard New 5 EL-006 JNT Project Setup
101418 MP 87.1 ANZEx Scheme for Certification of hazardous area equipment and service facilities that repair and overhaul hazardous area equipment.
Misc Publication Revision 5 P-008 AUS Project Setup
101419 MP 87.2 ANZEx Scheme for Certification of hazardous area equipment and service facilities that repair and overhaul hazardous area equipment.
Misc Publication Revision 5 P-008 AUS Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 19
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101420 MP 87.3 ANZEx Scheme for Certification of hazardous area equipment and service facilities that repair and overhaul hazardous area equipment.
Misc Publication New 5 P-008 AUS Project Setup
101585 Rul PP.2—2012 Rulings to Pipelines – Gas and liquid petroleum Standards, Ruling 2: Application of Pressure Piping Standard (Ruling to AS 2885.1—2012)
Ruling New 5 ME-038 AUS Project Setup
101274 SA TS IEC 61800.8 Adjustable speed electrical power drive systems – Part 8: Specification of voltage on the power interface
Technical Spec New 5 EL-027 AUS Public Commenting
101212 SA/SNZ TR IEC 60725 Consideration of reference impedances and public supply network impedances for use in determining the disturbance characteristics of electrical equipment having a rated current ≤ 75 A per phase
Technical Report New 5 EL-034 JNT Drafting
101218 SA/SNZ TR IEC 61000.3.14 Electromagnetic compatibility (EMC)- Assessment of emission limits for the connection of disturbing installations to LV power systems
Technical Report New 5 EL-034 JNT Drafting
101219 SA/SNZ TR IEC 61000.3.15 Electromagnetic compatibility (EMC)- Limits – Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
Technical Report New 5 EL-034 JNT Drafting
101215 SA/SNZ TS IEC 61000.3.5 Electromagnetic compatibility (EMC)- Limits – Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 75 A
Technical Spec Revision 5 EL-034 JNT Drafting
Water and Waste Services 6
5457 AS 1371 – 1973 Plastic Toilet Seats Standard Revision 6 WS-003 AUS Public Commenting
101515 AS 3500 Vacuum Sanitary & Stormwater Plumbing & Draining Standard Revision 6 WS-014 AUS Project Setup
100663 AS 4032.4 Thermostatic Mixing Taps – Materials, Design and Performance Requirements
Standard New 6 WS-026 AUS Public Commenting
100393 AS 4181 Repair and Off-take clamps for Waterworks purposes Standard Revision 6 WS-016 AUS Public Commenting
100692 AS 4747.1 Meters for non-urban water supply – Glossary of terms Standard New 6 CE-024 AUS Publication
100729 AS 4747.2 Meters for non-urban water supply – Specification for closed conduit meters fully charged.
Standard New 6 CE-024 AUS Publication
100730 AS 4747.3 Meters for non-urban water supply – Specifications for open channel meters
Standard New 6 CE-024 AUS Publication
100731 AS 4747.5 Meters for non-urban water supply – Installation and commissioning of closed conduit meters fully charged.
Standard New 6 CE-024 AUS Publication
100733 AS 4747.8 Meters for non-urban water supply – In-service compliance for non-urban water meters.
Standard New 6 CE-024 AUS Publication
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 20
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
7497 AS 5200.464 Hot water manual or sensor-activated pumping systems Standard Revision 6 WS-026 AUS Public Commenting
101304 AS 5612 Butterfly valves for general purposes Standard New 6 WS-022 AUS Styling, Editing & Graphics – Drafting
101372 AS/NZS 2053.23 Conduit Systems for cable management – Part 23: Particular requirements – Flexible conduit systems
Standard International Adoption – Modified
6 EL-004 JNT Public Commenting
100995 AS/NZS 2280 Ductile iron pipes and fittings Standard Revision 6 WS-016 JNT Drafting
101618 AS/NZS 2566.2 Buried flexible pipelines – Part 2: Installation Standard Correction Amendment
6 WS-028 JNT Public Commenting
101256 AS/NZS 3500.1 Plumbing and drainage, Part 1: Water Services Standard Revision 6 WS-014 JNT Drafting
101247 AS/NZS 3500.2 Plumbing and drainage, Part 2: Sanitary Plumbing and Drainage Standard Revision 6 WS-014 JNT Drafting
101248 AS/NZS 3500.5 Plumbing and drainage, Part 5: Domestic installations Standard Revision 6 WS-014 JNT Project Setup
101140 AS/NZS 3518 Acrylonitrile butadiene styrene (ABS) compounds, pipes and fittings for pressure applications
Standard Revision 6 PL-021 JNT Publication
100143 ATS 5200.106 Wastewater pumping units (Lifting plants) Technical Spec Revision 6 WS-031 AUS Balloting
8782 ATS 5200.498 Plastic waste fittings Technical Spec New 6 WS-031 AUS Publication
100210 ATS 5200.504 Water Closet System – Low volume flush water closet with included sewer dosing device
Technical Spec New 6 WS-031 AUS Balloting
100603 ATS 5200.506 Pumps for general use in plumbing water services applications (Rainwater tank pumps)
Technical Spec New 6 WS-031 AUS Drafting
101063 ATS 5200.507 Acrylonitrile butadiene styrene (ABS) piping system with stainless steel inner liner for water service applications
Technical Spec New 6 WS-031 AUS Balloting
101064 ATS 5200.509 Technical Specification for Polypropylene Access Chambers and Maintenance Shafts for Plumbing and Drainage
Technical Spec New 6 WS-031 AUS Public Commenting
101065 ATS 5200.510 Hot water manual time-activated pumping systems Technical Spec New 6 WS-031 AUS Public Commenting
101066 ATS 5200.511 Epoxy lining system for use in water supply applications Technical Spec New 6 WS-031 AUS Public Commenting
101416 HB39 Installation code for metal roof and wall cladding Handbook Revision 6 WS-014 AUS Drafting
7297 MP 52 Australian certification scheme for plumbing and drainage product Misc Publication Revision 6 P-009 AUS Public Commenting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 21
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
Transport and Logistics 7
100762 AS 1085.21 Railway track material – Turnouts, switches and crossings Standard New 7 CE-002 AUS Drafting
100415 AS 1375 Industrial Fuel Fired Appliances Standard Revision 7 AG-011 AUS Public Commenting
101465 AS 1418.8 Cranes, hoists and winches Part 8: Special purpose appliances – Tow trucks
Standard Revised Text Amendment
7 ME-005 AUS Project Setup
100884 AS 1742.1 Manual of uniform traffic control devices Parts 1: General introduction and index of signs
Standard Revision 7 MS-012 AUS Drafting
100885 AS 1742.14 Manual of uniform traffic control devices Part 14: Traffic signal Standard Revision 7 MS-012 AUS Drafting
100886 AS 1742.6 Manual of uniform traffic devices Part 6: Tourist and services signs Standard Revision 7 MS-012 AUS Drafting
100887 AS 1742.7 Manual of uniform traffic devices Part 7: Railway crossings Standard Revision 7 MS-012 AUS Drafting
100888 AS 1743 Road signs – Specifications Standard Revision 7 MS-012 AUS Drafting
100889 AS 1744 Standard alphabets for road signs Standard Revision 7 MS-012 AUS Drafting
101454 AS 2339 Traffic signal posts and attachments Standard Revision 7 LG-006 AUS Project Setup
101453 AS 2353 Pedestrian push button assemblies Standard Revision 7 LG-006 AUS Project Setup
100455 AS 2359.1 Powered industrial trucks – General Requirements Standard Revision 7 ME-026 AUS Drafting
100456 AS 2359.2 Powered industrial trucks – General Requirements Standard Revision 7 ME-026 AUS Publication
100824 AS 2359.6 Powered industrial trucks – Safety requriements and verification Part 6: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks.
Standard International Adoption – Modified
7 ME-026 AUS Publication
101473 AS 3562 Lighting equipment for bicycles Standard Revision 7 CS-110 AUS Project Setup
101452 AS 4191 Portable traffic signals Standard Revision 7 LG-006 AUS Project Setup
100792 AS 4732 LP Gas fuel systems for marine engines Standard Revision 7 ME-046 AUS Project Setup
101131 AS IEC 62196-2 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 2: Dimensional compatibility and interchangeability requirements for A.C. pin and contact-tube accessories
Standard International Adoption – Identical
7 EVO-001 AUS Balloting
100414 AS/NZS 1425 LP Gas Fuel Systems for Vehicle Engines Standard Revision 7 ME-046 JNT Public Commenting
101202 AS/NZS 1698 Batch testing regime for motorcycle helmets as a normative appendix to AS/NZS 1698
Standard Revised Text Amendment
7 CS-076 JNT Balloting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 22
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100440 AS/NZS 1754 Child restraint systems for use in motor vehicles Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101518 AS/NZS 1927 Pedal Bicycles – Safety Requirements Standard Revised Text Amendment
7 CS-110 JNT Project Setup
101517 AS/NZS 2063 Bicycle helmets Standard Revised Text Amendment
7 CS-110 JNT Project Setup
100989 AS/NZS 2144 Traffic Signal Lanterns Standard Revision 7 LG-006 JNT Drafting
101045 AS/NZS 3629.1 Methods of testing child restraints – Dynamic testing Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
100441 AS/NZS 3629.10 Methods of testing child restraints – Bite Test Standard New 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101049 AS/NZS 3629.11 Methods of testing child restraints – Measuring Energy Attenuation Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101050 AS/NZS 3629.12 Methods of testing child restraints – Test of openings in fabric and netting
Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101046 AS/NZS 3629.3 Methods of testing child restraints – Dynamic testing of upper anchorage components
Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101048 AS/NZS 3629.5 Methods of testing child restraints – Determination of quick-release device actuation force
Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101047 AS/NZS 3629.6 Methods of testing child restraints – Determination of recline angle Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
100442 AS/NZS 4370 Restraint of children with disabilities in motor vehicles Standard Revision 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 23
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100443 AS/NZS 5031 Accessories for child restraints Standard New 7 CS-085 JNT Styling, Editing & Graphics – Public Comment
101491 ASNZS 1141.17 Methods for sampling and testing aggregates – Voids in dry compacted filler
Standard Revision 7 CE-006 JNT Project Setup
101489 ASNZS 1141.7 Methods for sampling and testing aggregates – Apparent particle density of filler
Standard Revision 7 CE-006 JNT Project Setup
101490 ASNZS 1141.8 Methods for sampling and testing aggregates – Water-soluble fraction of filler
Standard Revision 7 CE-006 JNT Project Setup
101486 ASNZS 2891.10 Methods of sampling and testing asphalt – Water and volatile oils content
Standard Revision 7 CE-006 JNT Project Setup
101487 ASNZS 2891.11 Methods of sampling and testing asphalt – Degree of particle coating Standard Revision 7 CE-006 JNT Project Setup
101488 ASNZS 2891.14.5 Methods of sampling and testing asphalt – Field density tests – Density ratio of compacted asphalt
Standard Revision 7 CE-006 JNT Project Setup
101477 ASNZS 2891.2.1 Methods of sampling and testing asphalt – Sample preparation – Mixing, quartering and conditioning of asphalt in the laboratory
Standard Revision 7 CE-006 JNT Project Setup
101478 ASNZS 2891.5 Methods of sampling and testing asphalt – Determination of stability and flow – Marshall procedure
Standard Revision 7 CE-006 JNT Project Setup
101479 ASNZS 2891.7.1 Methods of sampling and testing asphalt – Determination of maximum density of asphalt – Water displacement method
Standard Revision 7 CE-006 JNT Project Setup
101480 ASNZS 2891.7.2 Methods of sampling and testing asphalt – Determination of maximum density of asphalt – Trichloroethane displacement method
Standard Revision 7 CE-006 JNT Project Setup
101481 ASNZS 2891.7.3 Methods of sampling and testing asphalt – Determination of maximum density of asphalt – Methylated spirits displacement
Standard Revision 7 CE-006 JNT Project Setup
101482 ASNZS 2891.8 Methods of sampling and testing asphalt – Voids and density relationships for compacted asphalt mixes
Standard Revision 7 CE-006 JNT Project Setup
101483 ASNZS 2891.9.1 Methods of sampling and testing asphalt – Determination of bulk density of compacted asphalt – Waxing procedure
Standard Revision 7 CE-006 JNT Project Setup
101484 ASNZS 2891.9.2 Methods of sampling and testing asphalt – Determination of bulk density of compacted asphalt – Presaturation method
Standard Revision 7 CE-006 JNT Project Setup
101485 ASNZS 2891.9.3 Methods of sampling and testing asphalt – Determination of bulk density of compacted asphalt – Mensuration method
Standard Revision 7 CE-006 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 24
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101455 TBA Uninterruptable Power supplies for roadside devices Standard New 7 LG-006 AUS Project Setup
101456 TBA Communications protocols for roadside devices Standard New 7 LG-006 AUS Project Setup
101495 TBA Operation of LP Gas automotive retail outlets Technical Spec New 7 ME-015 JNT Project Setup
101496 TBA Load restraint for LP Gas cylinder distribution Technical Spec New 7 ME-015 JNT Project Setup
Health and Community Services 8
101493 AS 1337.0 Personal eye protection – Eye and face protectors- vocabulary Standard Revision 8 SF-006 AUS Project Setup
101602 AS 4700.1 Implementation of Health Level Seven (HL7) Version 2.4 Standard Revision 8 IT-014 AUS Project Setup
101605 AS 4700.2 Implementation of Health Level Seven (HL7) Version 2.4 – Pathology and diagnostic imaging (diagnostics)
Standard Revision 8 IT-014 AUS Project Setup
101604 AS 4700.5 Implementation of Health Level Seven (HL7) Version 2.5: Immunisation messages
Standard Revision 8 IT-014 AUS Project Setup
101608 AS 4700.6 Implementation of Health Level Seven (HL7) Version 2.5: Referral, discharge and health record messaging
Standard Revision 8 IT-014 AUS Balloting
100977 AS 4846 Person and Provider Identification in Healthcare Standard Revision 8 IT-014 AUS Drafting
100555 AS 5550 E-health web services profile Standard New 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100559 AS 5551 E-health XML secured payload profiles Standard New 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100554 AS 5552 E-health secure message delivery Standard New 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
101598 AS 5630 National Tall Man Lettering Standard New 8 IT-014 AUS Drafting
100786 AS ISO 15189 Medical laboratories – Requirements for quality and competence Standard International Adoption – Identical
8 HE-029 AUS Balloting
101609 AS ISO 18308 Health informatics – Requirements for an electronic health record architecture
Standard International Adoption – Identical
8 IT-014 AUS Project Setup
101599 AS ISO/TS 14265 Health informatics — Classification of purposes for processing personal health information
Technical Spec International Adoption – Identical
8 IT-014 AUS Project Setup
101194 AS/NZS 1269.4 Occupational noise management, Part 4: Auditory assessment Standard Revision 8 AV-003 JNT Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 25
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101492 AS/NZS 1336 Recommended practices for occupational eye protection Standard Revision 8 SF-006 JNT Project Setup
101425 AS/NZS 3003 Electrical Installations -Patient Areas Standard Revision 8 EL-006 JNT Project Setup
7053 AS/NZS 3695.2 Wheelchairs – Electrically powered wheelchairs and their chargers Standard Revision 8 ME-067 JNT Public Commenting
6093 AS/NZS 3856.1 Hoists and ramps for people with disabilities – Vehicle Mounted Product Requirements
Standard Revision 8 ME-067 JNT Public Commenting
100147 AS/NZS 3856.2 Hoists and ramps for people with disabilities – Vehicle Mounted – Installation Requirements
Standard Revision 8 ME-067 JNT Public Commenting
101192 AS/NZS 4011 Single use examination gloves – specification Standard Revision 8 HE-013 JNT Drafting
101193 AS/NZS 4179 Single use sterile surgical rubber gloves – specification Standard Revision 8 HE-013 JNT Drafting
100397 AS/NZS 4187 Cleaning, disinfecting and sterilizing reusable medical and surgical instruments and equipment, and maintenance of associated environments in health care facilities
Standard Revision 8 HE-023 JNT Public Commenting
100563 ATS 4888.1 E-health electronic transfer of prescriptions – Logical information model Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100535 ATS 4888.2 E-health electronic transfer of prescriptions – Logical services model Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100538 ATS 4888.3 E-health electronic transfer of prescriptions – E-Prescription Clincal Document Architecture (CDA) exchange specification
Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100537 ATS 4888.4 E-health electronic transfer of prescriptions – Dispense record Clinical Document Architecture (CDA) exchange specification
Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100539 ATS 4888.5 E-health electronic transfer of prescriptions – Prescription request Clincal Document Architecture (CDA) exchange specification
Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100668 ATS 4888.6 E-health electronic transfer of prescription – Web Services Platform Specification
Technical Spec Other 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
100581 ATS 5338 HL7 V2 eReferral – V2 implementation profile Technical Spec New 8 IT-014 AUS Public Commenting
100536 HB 174 Information Security Management, Implementation guide for the health sector
Handbook Revision 8 IT-014 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 26
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101606 HB 262 Guidelines for messaging between diagnostics providers and heatlh service providers
Handbook Revision 8 IT-014 AUS Drafting
101593 Internal Guidleines Guidelines for the specification of conformity assessment schemes for e-health standards
Other Revision 8 IT-014 AUS Project Setup
100553 TBA E-health endpoint location service Technical Spec Revision 8 IT-014 AUS Styling, Editing & Graphics – Drafting
100212 TBA Core discharge summary structured document template Technical Spec New 8 IT-014 AUS Styling, Editing & Graphics – Public Comment
9007 TBA Implementation of HL7 V2.x Part 3: Electronic Messages for exchange of information on drug prescription
Standard Revision 8 IT-014 AUS Drafting
100211 TBA Discharge Summary – CDA Implementation Guide Technical Spec Other 8 IT-014 AUS Drafting
100213 TBA Core GP referral -V2 exchange specification Technical Spec New 8 IT-014 AUS Drafting
100505 TBA Core discharge summary – V2 exchange specification Technical Spec New 8 IT-014 AUS Drafting
100540 TBA Representation of structured cancer pathology reports in HL7 V2 messages
Technical Spec New 8 IT-014 AUS Drafting
100577 TBA Specification of a mechanism to access historical reports from diagnostic service providers
Technical Report New 8 IT-014 AUS Drafting
100602 TBA Harmonised data types for information interchange Misc Publication New 8 IT-014 AUS Drafting
100643 TBA Implementation of HL7 V2.x Part 3: electronic messages for exchange of information on drug prescription
Handbook Other 8 IT-014 AUS Drafting
100978 TBA eReferral – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Drafting
100979 TBA eNotification – HL7 V2 collaborative care responsibility message Standard New 8 IT-014 AUS Drafting
101128 TBA E-health Authentication Framework Handbook New 8 IT-014 AUS Drafting
101145 TBA eHealth Architecture Principles Handbook New 8 IT-014 AUS Drafting
101594 TBA Individual and Provider Identification – Workplace Implementation Handbook Revision 8 IT-014 AUS Drafting
101613 TBA Standards-based Clinical Decision Support for Australian Primary Care Technical Report New 8 IT-014 AUS Drafting
101614 TBA HL7 V2 Virtual Medical Record Profile Interim Standard New 8 IT-014 AUS Drafting
101615 TBA Integration Specifications for Australian Point of Care Systems to interoperate with Independent Clinical Decision Support Services, Components and Applications
Technical Spec New 8 IT-014 AUS Drafting
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 27
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100644 TBA Conformance criteria for existing diagnostics messaging standards Misc Publication New 8 IT-014 AUS Project Setup
101114 TBA Advanced Care Directive – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101115 TBA Advance Care Directive – Logical Content Specification Technical Spec New 8 IT-014 AUS Project Setup
101116 TBA CDA Authoring and Rendering Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101117 TBA CDA Conformance Profile Technical Spec New 8 IT-014 AUS Project Setup
101120 TBA Consumer Entered Information – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101121 TBA Consumer Entered Information – Logical Content Specification Technical Spec New 8 IT-014 AUS Project Setup
101122 TBA Event Summary – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101124 TBA Shared Health Summary – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101126 TBA Specialist Letter CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101129 TBA Consolidated View – CDA Implementation Guide Technical Spec New 8 IT-014 AUS Project Setup
101130 TBA Consolidated View – Logical Content Specification Technical Spec New 8 IT-014 AUS Project Setup
101132 TBA CDA V2 Messages Technical Report Other 8 IT-014 AUS Project Setup
101211 TBA Standardising colour coding and positioning of disinfectant solution, hand lotion and alcohol based rubs in relation to a sink in HealthCare settings.
Standard New 8 SF-021 AUS Project Setup
101384 TBA SMD Conformance Profile Technical Spec New 8 IT-014 AUS Project Setup
101595 TBA Healthcare Records – Electronic Healthcare Record Systems Standard New 8 IT-014 AUS Project Setup
101596 TBA Data Development and Maintenance in Health Systems Technical Spec Revision 8 IT-014 AUS Project Setup
101597 TBA Implementation of Clinical Terminology in Local Systems Technical Spec New 8 IT-014 AUS Project Setup
101600 TBA National eHealth Security and Access Framework (NESAF) Technical Spec New 8 IT-014 AUS Project Setup
101601 TBA Implementation Guide for Health Level Seven (HL7) HL7 V2.6 Standard New 8 IT-014 AUS Project Setup
101603 TBA Implementation of Health Level Seven (HL7) Version 2.5 and Version 2.5.1
Standard Revision 8 IT-014 AUS Project Setup
101607 TBA HL7 Clinical Document Architecture (CDA) – Guidance for Implementation in Australia
Handbook New 8 IT-014 AUS Project Setup
101610 TBA Recommendations on the delivery of, access to and viewing of diagnostic quality digital images for clinicians
Technical Spec New 8 IT-014 AUS Project Setup
101611 TBA Discussion paper for standardised network-to-network interconnects Misc Publication New 8 IT-014 AUS Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 28
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101612 TBA Chronic Disease Management with telehealth using ContSys (CEN standard EN13940)
Misc Publication New 8 IT-014 AUS Project Setup
100504 TBA eReferral – Logical Content Specification Technical Spec New 8 IT-014 AUS Public Commenting
101119 TBA Collaborative Care- Logical Content Model Technical Spec New 8 IT-014 AUS Public Commenting
101123 TBA Event Summary – Logical Content Specification Technical Spec New 8 IT-014 AUS Public Commenting
101125 TBA Shared Health Summary – Logical Content Specification Technical Spec New 8 IT-014 AUS Public Commenting
101127 TBA Specialist Letter – Logical Content Specification Technical Spec New 8 IT-014 AUS Public Commenting
5281 TR 4896 Health informatics – Electronic health record communication – Part 1: Reference model
Technical Report New 8 IT-014 AUS Drafting
Consumer Products and Services and Safety 9
101160 AS 2432 Babies’ dummies Standard Revision 9 CS-040 AUS Drafting
101464 AS 4685.1 Playground equipment – General safety requirements and test methods Standard Revision 9 CS-005 AUS Project Setup
100956 AS 5588 Grapevine Standard Standard New 9 FT-036 AUS Drafting
100924 AS NZS 2088 Revision of AS/NZS 2088:2009 Prams and strollers—Safety requirements
Standard Revision 9 CS-020 JNT Public Commenting
100923 AS NZS 2172 Cots for household use—Safety requirements Standard Revision 9 CS-003 JNT Styling, Editing & Graphics – Public Comment
100356 AS/NZS 1249 Children's nightwear and limited daywear having reduced fire hazard Standard Revision 9 CS-086 JNT Drafting
100999 AS/NZS 1900 Flotation aids for water familiarization and swimming tuition Standard Revision 9 CS-021 JNT Drafting
101004 AS/NZS 3813 Plastic monobloc chairs Standard Revision 9 CS-088 JNT Drafting
101269 AS/NZS 4012 Domestic solid fuel burning appliances-Method for determination of power output and efficiency
Standard Revision 9 CS-062 JNT Project Setup
101268 AS/NZS 4013 Domestic Solid Fuel Burning Appliances – Method for determination of flue gas emissions
Standard Revision 9 CS-062 JNT Project Setup
101592 AS/NZS 4935 Domestic furniture—Freestanding chests of drawers, wardrobes and bookshelves/bookcases—Determination of stability
Standard Correction Amendment
9 CS-088 JNT Public Commenting
101159 AS/NZS 8811.1 Method of test for infant sleep products Standard Revision 9 CS-003 JNT Styling, Editing & Graphics – Public Comment
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 29
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101019 AS/NZS ISO 8124.1:2013 Safety of toys – Part 1: Safety aspects related to mechanical and physical properties Amd 3
Standard International Adoption – Identical
9 CS-018 JNT Public Commenting
101527 AS/NZS ISO/IEC 17021.2 Conformity assessment – Requirements for bodies providing audit and certification of management systems – Part 2: Competence requirements for auditing and certification of environmental management systems
Standard International Adoption – Identical
9 QR-011 JNT Public Commenting
101523 AS/NZS ISO/IEC 17065 Conformity assessment – Requirements for bodies certifying products, processes and services
Standard International Adoption – Identical
9 QR-010 JNT Project Setup
101407 RUL BA.1-2012 Rulings to buoyancy aids standards – Indicators for inflation of personal flotation devices (Ruling to AS 4758.2)
Ruling New 9 CS-060 AUS Project Setup
Education and Training Services 10
101588 TBA National Boarding Standards for Australian Schools Standard New 10 TBC AUS Project Setup
Communication, Information Technology and e-Commerce Services 11
101163 AS 4599.1 Digital television – Terrestrial broadcasting – Characteristics of digital terrestrial television transmissions
Standard Revision 11 CT-002 AUS Drafting
101591 AS 4933.1 Digital television – Requirements for receivers – Part 1: VHF/UHF DVB-T television broadcasts,
Standard Revision 11 CT-002 AUS Project Setup
101520 AS ISO 12646 Characteristics and viewing conditions Standard International Adoption – Identical
11 EX-004 AUS Public Commenting
101519 AS ISO 12647.3 Graphic technology – Process control for the production of half-tone colour separations, proofs and production prints – Part 3: Coldset offset lithography on newsprint
Standard International Adoption – Identical
11 EX-004 AUS Public Commenting
101561 AS ISO/IEC 20000-1 Information technology – Service management: Part 1: Service management requirement systems
Standard International Adoption – Identical
11 IT-030 AUS Project Setup
101562 AS ISO/IEC 20000-2 Information technology – Service management: Part 2: Guidance on the application of service management systems
Standard International Adoption – Identical
11 IT-030 AUS Project Setup
101229 AS/NZ ISO 19155 Geographic Information/Geomatics – ISO 19155 Place Identifier (PI) Architecture
Standard International Adoption – Identical
11 IT-004 JNT Drafting
101548 AS/NZS 15939 Software Engineering – Software Measurement Process. Standard Revision 11 IT-015 JNT Project Setup
101531 AS/NZS 2632.2 Codes for the representation of names of countries and their subdivisions – Part 2: Country subdivision code
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 30
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
100402 AS/NZS 3080:2003 Information technology – Generic cabling for customer premises Standard Revision 11 CT-001 JNT Public Commenting
101460 AS/NZS 4280.1 Marine Emergency Position-Indicating Radio Beacons Standard Revised Text Amendment
11 RC-004 JNT Project Setup
101461 AS/NZS 4280.2 Personal Locator Beacons Standard Revised Text Amendment
11 RC-004 JNT Project Setup
101462 AS/NZS 4582 MF & HF radiocommunications equipment in the international maritime mobile radiotelephone service
Standard Revised Text Amendment
11 RC-004 JNT Project Setup
101392 AS/NZS 4769.1 Radiocommunications equipment used in the paging service – Angle modulated equipment
Standard Reconfirmation 11 RC-006 JNT Publication
101393 AS/NZS 4769.2 Radiocommunications equipment used in the paging service – Amplitude modulated equipment
Standard Reconfirmation 11 RC-006 JNT Publication
101394 AS/NZS 4770 MF and HF radiocommunications equipment in the land mobile service utilizing single sideband suppressed carrier emission
Standard Reconfirmation 11 RC-006 JNT Publication
101463 AS/NZS 4869 Standalone Maritime survivor locating systems, operating on frequencies other than 121.5 MHz
Standard Revised Text Amendment
11 RC-004 JNT Project Setup
100329 AS/NZS 5377 Collection, storage, transport and treatment of used electrical and electronic equipment
Standard New 11 EV-019 JNT Publication
100301 AS/NZS 5478 National recordkeeping metadata element set Standard New 11 IT-021 JNT Drafting
101565 AS/NZS 61000.4.2 Electromagnetic compatibility (EMC) – Testing and measurement techniques – Electrostatic discharge immunity test
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101566 AS/NZS 61000.4.3 Electromagnetic compatibility (EMC) – Testing and measurement techniques – Radiated, radio-frequency, electromagnetic field immunity test
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101567 AS/NZS 61000.4.4 Electromagnetic compatibility (EMC) – Testing and measurement techniques – Electrical fast transient/burst immunity test
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101568 AS/NZS 61000.4.6 Electromagnetic compatibility (EMC) – Testing and measurement techniques – Immunity to conducted disturbances, induced by radio-frequency fields
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101043 AS/NZS 8016 Governance of IT Enabled Projects Standard Reconfirmation 11 IT-030 AUS Public Commenting
101575 AS/NZS CISPR 12 Vehicles, boats and internal combustion engines – Radio disturbance characteristics – Limits and methods of measurement for the protection of off-board receivers
Standard Revision 11 TE-003 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 31
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101576 AS/NZS CISPR 14.1 Electromagnetic Compatibility—Requirements for household appliances, electrical tools and similar apparatus – Emission
Standard Revision 11 TE-003 JNT Project Setup
101220 AS/NZS CISPR 14.2 Immunity Standard for household appliances, electric tools and similar apparatus
Standard International Adoption – Identical
11 TE-003 JNT Balloting
101239 AS/NZS CISPR 16.1.4 Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-4: Radio disturbance and immunity measuring apparatus – Antennas and test sites for radiated disturbance measurements
Standard International Adoption – Identical
11 TE-003 JNT Publication
101569 AS/NZS CISPR 16.1.5 Specification for radio disturbance and immunity measuring apparatus and methods – Radio disturbance and immunity measuring apparatus – Antenna calibration test sites for 30 MHz to 1000 MHz
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101571 AS/NZS CISPR 16.2.5 Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-5: In situ measurements for disturbing emissions produced by physically large equipment
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101570 AS/NZS CISPR 16.3 Specification for radio disturbance and immunity measuring apparatus and methods – CISPR technical reports
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101244 AS/NZS CISPR 16.4.2 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-2: Uncertainties, statistics and limit modelling – Measurement instrumentation uncertainty
Standard International Adoption – Identical
11 TE-003 JNT Public Commenting
101572 AS/NZS CISPR 16.4.5 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4-5: Uncertainties, statistics and limit modelling – Conditions for the use of alternative test methods
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101573 AS/NZS CISPR 24 Information technology equipment – Immunity characteristics – Limits and methods of measurement
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
101574 AS/NZS CISPR 32 Electromagnetic compatibility of multimedia equipment – Emission requirements
Standard International Adoption – Identical
11 TE-003 JNT Project Setup
100870 AS/NZS ISO 19117 Geographic information/geomatics – Portrayal Standard Revision 11 IT-004 JNT Public Commenting
101537 AS/NZS ISO 26324 Information and Documentation – Digital Object Identifier Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101025 AS/NZS ISO 27037 Information technology — Security techniques — Guidelines for identification, collection, acquisition, and preservation of digital evidence.
Standard International Adoption – Modified
11 IT-012 JNT Drafting
101538 AS/NZS ISO 2709 Information and documentation – Format for Information Exchange Standard International Adoption – Identical
11 IT-019 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 32
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101536 AS/NZS ISO 27730 Information and Documentation – International Standard Collection Identifier (ISCI)
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101539 AS/NZS ISO 28560.1 Information and documentation – RFID in libraries – Part 1: Data elements and general guidelines for implementation
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101540 AS/NZS ISO 28560.2 Information and documentation – RFID in libraries – Part 2: Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101541 AS/NZS ISO 28560.3 Information and documentation – RFID in libraries – Part 3: Fixed length encoding
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101530 AS/NZS ISO 8459 Information and documentation – Bibliographic data element directory for use in data exchange and enquiry
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101545 AS/NZS ISO IEC 15026-2 Systems and software engineering — Systems and software assurance — Part 2: Assurance Case
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101546 AS/NZS ISO IEC 15026-3 Systems and software engineering — Systems and software assurance — Part 3: System integrity levels
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101547 AS/NZS ISO IEC 15026-4 Systems and software engineering — Systems and software assurance — Part 4: Assurance in the life cycle
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101578 AS/NZS ISO IEC 15504-5 Information technology – Process assessment – Part 5: An exemplar software life cycle process assessment model
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101549 AS/NZS ISO IEC 24773 Software Engineering – Certification of Software Engineers Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101551 AS/NZS ISO IEC 25001 Software engineering: Software product Quality Requirements and Evaluation (SQuaRE) – Planning and management ISO/IEC 25010:2011 Systems and software engineering – Systems and software Quality Requirements and Evaluation (SQuaRE) – System and softwa
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101552 AS/NZS ISO IEC 25010 SQuaRE System and software Quality Models Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101553 AS/NZS ISO IEC 25012 SQuaRE Data quality model Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101554 AS/NZS ISO IEC 25020 SQuaRE Measurement reference model and guide Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101555 AS/NZS ISO IEC 25021 SQuaRE Quality measure elements Standard International Adoption – Identical
11 IT-015 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 33
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101556 AS/NZS ISO IEC 25030 SQuaRE Quality requirements Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101557 AS/NZS ISO IEC 25040 SQuaRE Evaluation process Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101558 AS/NZS ISO IEC 25041 SQuaRE Evaluation Guide for Developers, Acquirers and Evaluators Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101559 AS/NZS ISO IEC 25045 SQuaRE Evaluation Module for Recoverability Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101550 AS/NZS ISO IEC 42010 Systems and software engineering — Recommended practice for architectural description of software-intensive systems
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101544 AS/NZS ISO IEC TS 15026-1 Systems and software engineering — Systems and software assurance — Part 1: Concepts and vocabulary
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101577 AS/NZS ISO IEC TS 15504-8 Information technology – Process assessment – Part 8: An exemplar process assessment model for IT service management
Standard International Adoption – Identical
11 IT-015 JNT Project Setup
101533 AS/NZS ISO/IEC 12785.1 Information technology – Learning, education, and training – Content packaging – Part 1: Information model
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101534 AS/NZS ISO/IEC 12785.2 Information technology – Learning, education, and training – Content packaging – Part 2: XML binding
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
100410 AS/NZS ISO/IEC 14763-2 Planning and installation of copper cabling Standard Revision 11 CT-001 JNT Project Setup
100412 AS/NZS ISO/IEC 14763-2-1 Information technology – Implementation and operation of customer premises cabling – Part 2-1: Planning and installation of copper cabling – Identifiers within administration systems
Standard International Adoption – Identical
11 CT-001 JNT Project Setup
100407 AS/NZS ISO/IEC 15018 Information technology – Generic cabling for homes Standard Revised Text Amendment
11 CT-001 JNT Project Setup
101532 AS/NZS ISO/IEC 19788.1 Information technology – Learning, education and training – Metadata for learning resources – Part 1: Framework
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101580 AS/NZS ISO/IEC 19788.2 Information technology – Learning, education and training – Metadata for learning resources – Part 2: Dublin Core elements
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101581 AS/NZS ISO/IEC 19788.3 Information technology – Learning, education and training – Metadata for learning resources – Part 3: Basic application profile
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101582 AS/NZS ISO/IEC 19788.5 Information technology – Learning, education and training – Metadata for learning resources – Part 5: Educational elements
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 34
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101542 AS/NZS ISO/IEC 19796.1 Information technology – Learning, education and training – Quality management, assurance and metrics – Part 1: General approach
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101543 AS/NZS ISO/IEC 19796.3 Information technology – Learning, education and training – Quality management, assurance and metrics – Part 3: Reference methods and metrics
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
101303 HB 116 Guide to Australian Modelling & Simulation Standards Handbook New 11 IT-031 AUS Drafting
100413 HB 252 Residential communications cabling Handbook Standard Revision 11 CT-001 AUS Project Setup
101535 SA/NZS ISO/IEC TR 12785.3 Information technology – Learning, education, and training – Content packaging – Part 3: Best practice and implementation guide
Standard International Adoption – Identical
11 IT-019 JNT Project Setup
Public Safety; Public Administration; Business and Management 12
101474 AS 2243.4 Safety in laboratories Part 4: Ionizing radiations Standard Revision 12 CH-026 AUS Project Setup
100398 AS 2252.5 Controlled environments – Design, installation and use of cytotoxic drug safety cabinets
Standard Revision 12 ME-060 AUS Drafting
100879 AS 3533.4.2 Amusement rides and devices – Part 4.2: Specific requirements – Contained play facilities
Standard New 12 ME-051 AUS Publication
101290 AS 3533.4.4 Karting Standard Revision 12 ME-051 AUS Drafting
101235 AS 4774.2 Work in Compressed Air and Hyperbaric Facilities, Part 2 Hyperbaric Oxygen facilities
Standard Revision 12 SF-046 AUS Project Setup
100812 AS 4989 Trampolines— Safety aspects Standard Revision 12 CS-100 AUS Drafting
100418 AS 5388.3 Interpretation of Results from the Analysis of Physical Material for Forensic Purposes
Standard New 12 CH-041 AUS Public Commenting
100419 AS 5388.4 Reporting Results and Conclusions from the Analysis of Physical Material for Forensic Purposes
Standard New 12 CH-041 AUS Balloting
101306 AS 5620 Workforce Planning Standard New 12 MB-009 AUS Drafting
100754 AS 7240.16 Fire detection and alarm systems – Part 16: Sound System Control and Indicating Equipment
Standard Revision 12 FP-002 AUS Drafting
101526 AS ISO 2631.1 Mechanical vibration and shock – evaluation of human exposure to whole body viabration – Part 1 : general requirements amendment 1
Standard International Adoption – Identical
12 AV-010 AUS Project Setup
101524 AS ISO 5349.1 Mechanical vibration – Measurement and evaluation of human exposure to hand-transmitted vibration – Part 1: General requirements
Standard International Adoption – Identical
12 AV-010 AUS Project Setup
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 35
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101525 AS ISO 5349.2 Mechanical vibration – Measurement and evaluation of human exposure to hand-transmitted vibration – Part 2: Practical guidance for measurement at the workplace
Standard International Adoption – Identical
12 AV-010 AUS Project Setup
101616 AS/NZS 5911 General guidelines on the verification, validation and assurance of environmental and sustainability reports
Standard Other 12 QR-011 JNT Balloting
101370 AS/NZS 10002 Quality Management: Customer Satisfaction--Guidelines for Complaints Handling
Standard New 12 QR-015 JNT Drafting
101405 AS/NZS 1715 Selection, use and maintenance of respiratory protective equipment – Ruling to AS/NZS 1715-2009
Ruling Other 12 SF-010 JNT Publication
101522 AS/NZS 19011 Guidelines for auditing management systems Standard International Adoption – Identical
12 QR-006 JNT Project Setup
101417 AS/NZS 2243.8 Revision of AS 2243.8 to include manifold duct systems Standard Revision 12 CH-026 JNT Drafting
101261 AS/NZS 2299.1 Occupational diving operations – Standard operational practice Standard Revision 12 SF-017 JNT Drafting
101263 AS/NZS 2815.2 Surface supplied diving to 30 m Standard Revision 12 SF-017 JNT Public Commenting
101262 AS/NZS 2815.5 Training and certification of occupational divers – Dive supervisor Standard Revision 12 SF-017 JNT Styling, Editing & Graphics – Drafting
101264 AS/NZS 2815.6 Training and certification of occupational divers – Restricted occupational SCUBA diver
Standard New 12 SF-017 JNT Public Commenting
101476 AS/NZS 3957 Light-transmitting screens and curtains for welding operations Standard Revision 12 SF-006 JNT Project Setup
100750 AS/NZS 4602.2 High Visibility Garments for Fire Service Personnel Standard New 12 SF-004 JNT Styling, Editing & Graphics – Public Comment
101529 AS/NZS ISO/IEC 17020 Conformity assessment – Requirements for the operation of various types of bodies performing inspection
Standard International Adoption – Identical
12 QR-010 JNT Public Commenting
101528 AS/NZS ISO/IEC 17024 Conformity assessment – General requirements for bodies operating certification of persons
Standard International Adoption – Identical
12 QR-010 JNT Project Setup
100808 AS/NZS2161.6 Occupational Protective Gloves Part 6 – Protective Gloves for Firefighters Laboratory Test Methods and Performance Requirements
Standard Revision 12 SF-049 JNT Public Commenting
100062 HB 436 Risk Management Guidelines – Companion to AS/NZS 4360: 2004 Handbook Other 12 OB-007 AUS Drafting
100507 TBA Standard Guidelines for Subsurface Utility Engineering (SUE) in Australia and New Zealand
Standard New 12 IT-036 JNT Styling, Editing & Graphics – Public Comment
Active and Approved Project Listing—By Sectoras at 31 January 2013
Page 36
ID Standard Number Title Product Type Project Type Sector Committee Allocation Development Stage
101369 TBA Organisation Management System Handbook New 12 QR-008 JNT Drafting