AUO Confidential For PROMATE Internal Use Only / 2009/4/29chuanling.net/down/M170EG01 VG.pdf · AU OPTRONICS CORPORATION Product Specification document version1.2 2/25

AU OPTRONICS CORPORATION Product Specification

document version1.2 1/25

M170EG01 VG

( ) Preliminary Specification ( V ) Final Specification

Module 17.0” SXGA Color TFT-LCD Model Name M170EG01 VG

Customer Date

Approved by

Note: This Specification is subject to change without notice.

Checked & Approved by Date

Sean Chen 2009/3/9

Prepared by

Stanley Su 2009/3/6

Desktop Display Business Group / AU Optronics corporation

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Contents

1. Handling Precautions.............................................................................................................. 4 2. General Description ................................................................................................................ 5

2.1 Display Characteristics ....................................................................................................................... 5 3. Functional Block Diagram .................................................................................................... 10 4. Absolute Maximum Ratings.................................................................................................. 11

4.1 TFT LCD Module ............................................................................................................................. 11 4.2 Backlight Unit ................................................................................................................................... 11 4.3 Absolute Ratings of Environment ..................................................................................................... 11

5. Electrical characteristics ...................................................................................................... 12 5.1 TFT LCD Module ............................................................................................................................. 12 5.2 Backlight Unit ................................................................................................................................... 14

6. Signal Characteristic............................................................................................................. 15 6.1 Pixel Format Image........................................................................................................................... 15 6.2 The Input Data Format ...................................................................................................................... 15 6.4 Timing Characteristics ...................................................................................................................... 18 6.5 Power ON/OFF Sequence................................................................................................................. 20

7. Connector & Pin Assignment ............................................................................................... 21 7.1 TFT LCD Module ............................................................................................................................. 21 7.2 Backlight Unit ................................................................................................................................... 22

8. Reliability Test ....................................................................................................................... 23 9. Shipping Label....................................................................................................................... 24 10. Mechanical Characteristics ................................................................................................ 25

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Record of Revision

Version and Date Page Old description New Description Remark

0.1 2008/9/8 All First Edition for Customer All

1.0 2008/11/26 5 Power Consumption TBD (Typ) (PDD=TBD, PCFL=9.45W @Lamp=7.5mA)

Power Consumption 11.75 (Typ) (PDD=2.3, PCFL=9.45W @Lamp=7.5mA)

Modify

12

Input Current Typ.:1.2 Max:1.56 VCCPower Typ.:TBD Max:7.8

Input Current Typ.:0.46 Max:0.48 VCCPower Typ.:2.3 Max:2.64

Modify

14 CCFL Life Time Min:40,000 Typ.:50,000

CCFL Life Time Min:50,000 Typ.:- Modify

1.1 2009/2/4 18 Clock Period Max:-

Clock Period Max:25

Modify

20 T6 Max:10

T6 Max:-

Modify

1.2 2009/3/9 5 Power Consumption(VDD line + CCFL line)

11.75W (Typ.) (without inverter, all black pattern)

Power Consumption(VDD line + CCFL line)

14.7W (Typ.) (without inverter, all black pattern)

Modify

12

Input Current Typ.:0.46 Max8:0.4 VCCPower Typ.:2.3 Max:2.64 VCCrp Max:100

Input Current Typ.:1.05 Max:1.16 VCCPower Typ.:5.25 Max:5.8 VCCrp Max:200

Modify

AUO C

onfid

entia

l For

PROMATE Inter

nal U

se O

nly / 2

009/4

/29



M170EG01 VG

1. Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth

when handling. 7) Do not open or modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after once it was taken out

from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module.

11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.

12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal.

13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption.

14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

2. General Description This specification applies to the 17 inch Color TFT-LCD Module M170EG01 VG. The display supports the SXGA+ (1280(H) x 1024(V)) screen format and 16.7M colors (RGB 6-bits+Hi-RFC data).All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 condition:

Items Unit Specifications Screen Diagonal [mm] 432 (17.0”) Active Area [mm] 337.920(H) × 270.336(V) Pixels H x V 1280 × 3(RGB) × 1024 Pixel Pitch [mm] 0.264(per one triad) × 0.264 Pixel Arrangement R.G.B. Vertical Stripe Display Mode Normally White White Luminance [cd/m2] 250 (center,Typ)@7.5 mA Contrast Ratio 1000 : 1 (Typ) Optical ResponseTime [msec] 5 (Typ) Nominal Input Voltage VDD [Volt] +5.0 (Typ) Power Consumption (VDD line + CCFL line) [Watt] 14.7W (Typ.)

(without inverter, all black pattern) Weight [Grams] 1990 Typ. Physical Size (H x V x D) [mm] 358.5(H) x 296.5(V) Typ. x 15.8(D) Max. Electrical Interface Dual Channel LVDS Surface Treatment Anti-glare type, Hardness 3H Support Color 16.7M colors (RGB 6-bits +Hi-FRC data) Temperature Range

Operating Storage (Non-Operating)

[oC] [oC]

0 to +50

-20 to +60 RoHS Compliance RoHS Compliance Digital Gamma turn on Compliance TCO03 Compliance

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 (Room Temperature):

Item Unit Conditions Min. Typ. Max. Note Horizontal (Right) CR = 10 (Left)

70 70

85 85 -

Vertical (Up) CR = 10 (Down)

70 70

80 80 -

Horizon (Right) CR = 5 (Left)

75 75

85 85 -

Viewing Angle [degree]

Vertical (Up) CR = 5 (Down)

75 75

85 85 -

1

Luminance Uniformity [%] 9 Points 75 80 - 2, 3 Rising - 3.5 6 Falling - 1.5 3 Optical Response Time [msec] Rising + Falling - 5 9

4, 6

Red x 0.618 0.648 0.678 Red y 0.309 0.339 0.369 Green x 0.262 0.292 0.322 Green y 0.573 0.603 0.633 Blue x 0.113 0.143 0.173 Blue y 0.040 0.070 0.100 White x 0.283 0.313 0.343

Color / Chromaticity Coordinates (CIE 1931)

White y 0.299 0.329 0.359

4

White Luminance (At CCFL= 7.5mA) [cd/m2 ] 200 250 - 4

Contrast Ratio 600 1000 - 4 Cross Talk (At 75Hz) [%] - - 1.5 5 Flicker [dB] - - -20 7

Optical Equipment: BM-5A, BM-7, PR880, or equivalent

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Note 1: Definition of viewing angle Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle.

Note 2: 9 points position Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the minimum test point luminance

Minimum Luminance of 9 points δW9 = Maximum Luminance of 9 points

50 %

90 %

90 % 50 %

10 %

10 %

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.

Note 5: Definition of Cross Talk (CT) CT = | YB – YA | / YA × 100 (%) Where

YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Center of the screen

TFT-LCD Module

50 cm

Photo detector

LCD Panel

Field=2°

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Note 6: Definition of response time: The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full White” (rising time), and from “Full White” to “Full Black ”(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.

Note 7: Subchecker Pattern

R G B R G B

R G B R G B

R G B R G B

Method: Record dBV & DC value with (WESTAR)TRD-100

Level DCHz) 30Level(at AClog20(dB)Flicker =

100 90

10 0

%

Optical response

White Black White

Tr F Tr R

100 90

10 0

%

Optical response

White Black White

Tr F Tr R

Gray Level = L127

Gray Level = L0

Amplitude

Time

DC

AC

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

3. Functional Block Diagram The following diagram shows the functional block of the 17.0 inches Color TFT-LCD Module:

JAE FI-XB30SSL-HF15 YENONHO 35001WR-00LS00 STM MSBKT2407P30HB CVILUX CP0502SL090

2 CCFL

Connector

DC/DC Converter

LVDS Receiver

Timing Controller

Gamma Correction

TFT-LCD 1280*(3)*1024

Pixels

Y-Driver IC G1

G1024 D1 D3840

Inverter DC POWER

AU ASIC

RSDS

LVDS

+ 5V

I/F + X-PCB

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

4. Absolute Maximum Ratings Absolute maximum ratings of the module is as following:

4.1 TFT LCD Module Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage VIN -0.3 6 [Volt] Note 1,2 4.2 Backlight Unit

Item Symbol Min Max Unit Conditions CCFL Current ICFL - 8 [mA] rms Note 1,2

4.3 Absolute Ratings of Environment

Item Symbol Min Max Unit Conditions Operating Humidity HOP 5 90 [%RH] Storage Temperature TST -20 +60 [oC] Storage Humidity HST 5 90 [%RH]

Note 3

Note 1: With in Ta (25 ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).

Operating Range Storage Range AUO C

onfid

entia

l For

PROMATE Inter

nal U

se O

nly / 2

009/4

/29



M170EG01 VG

5. Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows: Symble Parameter Min. Typ. Max. Unit Condition

VCC Logic/LCD Drive Voltage 4.5 5.0 5.5 [Volt] ±10%

ICC Input Current - 1.05 1.16 [A] Vin=5V , All Black Pattern, at 75Hz

IRush Inrush Current - - 3.0 [A] Note

PCC VCCPower - 5.25 5.8 [Watt] Vin=5V , All Black Pattern, at 75Hz

VCCrp Allowable Logic/LCD Drive Ripple Voltage - - 200 [mV]

p-p With panel loading

Note: Measurement conditions:

+5.0V

+12.0V

VCC

R147K

R2

1K

VR147K

SW1SW MAG-SPST

12

F1

Q3AO6402

G

D2S

D1 D5 D6

C11uF/16V

Q3AO6402

G

D2 SD1

D5D6

C3

0.01uF/25V

C21uF/25V

(High to Low)ControlSignal

(LCD Module Input)

90%

10% VDD rising time 0V

5.0V

0.5ms AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows;

Symbol Parameter Min Typ Max Units Condition VTH Differential Input High

Threshold - - +100 [mV] VICM = 1.2V Note

VTL Differential Input Low Threshold -100 - - [mV] VICM = 1.2V

Note VID Input Differential Voltage 100 400 600 [mV] Note

VICM Differential Input Common Mode Voltage +1.0 +1.2 +1.5 [V] VTH/VTL = ±100MV

Note

Note: LVDS Signal Waveform

VTH VID

VICM

VSS

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

5.2 Backlight Unit Parameter guideline for CCFL Inverter

Parameter Min. Typ. Max. Unit Condition CCFL standard current(ISCFL) 7 7.5 8 [mA] rms (Ta=25oC) Note 2 CCFL Operation Current (IRCFL) 3 7.5 8 [mA] rms (Ta=25oC) Note 2 CCFL Frequency (FCFL) 40 60 80 [KHz] (Ta=25oC) Note 3,4 CCFL Ignition Voltage (ViCFL, Ta= 0) 1560 - [Volt] rms (Ta=0oC) Note 5 CCFL Ignition Voltage (ViCF, Ta= 25) 1200 - [Volt] rms (Ta=25oC) Note 5 CCFL Operation Voltage (VCFL) 580

@ 7.5mA 630

@ 7.5mA 680

@ 7.5mA [Volt] rms (Ta=25oC) Note 6 CCFL Power Consumption (PCFL) 8.7 9.45 10.2 [Watt] (Ta=25oC) Note 6 CCFL Life Time (LTCFL) 50,000 - - [Hour] (Ta=25oC)

Note 1: Typ. are AUO recommended design points. *1 All of characteristics listed are measured under the condition using the AUO test inverter. *2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.

Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen.

*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.

*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to keep on applying kick-off voltage for 1 [Sec] until discharge.

*5 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter.

Note 2: It should be employed the inverter which has “Duty Dimming”, if IRCFL is less than 3mA. Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter

and TFT LCD. Note 4: The frequency range will not affect to lamp life and reliability characteristics. Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,560

voltage. Lamp units need 1,560 voltage minimum for ignition. Note 6: The variance of CCFL power consumption is ±10%. Calculator value for reference (ISCFL × VCFL ×

2= PCFL) Note 7:Definition of Life time: Brightness becomes 50%. The typical life time CCFL in on the condition at 7.5

m A lamp current. AUO C

onfid

entia

l For

PROMATE Inter

nal U

se O

nly / 2

009/4

/29



M170EG01 VG

6. Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format.

R G B R G B

R G B R G B

R G B R G B

R G B R G B

1 2 1279 1280

1st Line

1024th Line

6.2 The Input Data Format

Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: Please follow PSWG. Note3: 8-bit in AUO C

onfid

entia

l For

PROMATE Inter

nal U

se O

nly / 2

009/4

/29



M170EG01 VG

6.3 Signal Description The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.

PIN # SIGNAL NAME DESCRIPTION 1 RxO0- Negative LVDS differential data input (Odd data) 2 RxO0+ Positive LVDS differential data input (Odd data) 3 RxO1- Negative LVDS differential data input (Odd data) 4 RxO1+ Positive LVDS differential data input (Odd data) 5 RxO2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) 6 RxO2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) 7 GND Power Ground 8 RxOC- Negative LVDS differential clock input (Odd clock) 9 RxOC+ Positive LVDS differential clock input (Odd clock) 10 RxO3- Negative LVDS differential data input (Odd data) 11 RxO3+ Positive LVDS differential data input (Odd data) 12 RxE0- Negative LVDS differential data input (Even data) 13 RxE0+ Positive LVDS differential data input (Even data) 14 GND Power Ground 15 RxE1- Negative LVDS differential data input (Even data) 16 RxE1+ Positive LVDS differential data input (Even data) 17 GND Power Ground 18 RxE2- Negative LVDS differential data input (Even data) 19 RxE2+ Positive LVDS differential data input (Even data) 20 RxEC- Negative LVDS differential clock input (Even clock) 21 RxEC+ Positive LVDS differential clock input (Even clock) 22 RxE3- Negative LVDS differential data input (Even data) 23 RxE3+ Positive LVDS differential data input (Even data) 24 GND Power Ground 25 GND Power Ground (For AUO test Aging+HVS mode ) 26 NC No contact 27 GND Power Ground 28 VCC +5.0V Power Supply 29 VCC +5.0V Power Supply 30 VCC +5.0V Power Supply

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

Note1: Start from left side Note2: Input signals of odd and even clock shall be the same timing. Note3: Please follow PSWG.

Connector

1 30

RxOIN0-

VCC

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

6.4 Timing Characteristics 6.4.1 Timing Characteristics Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.

Signal Item Symbol Min Typ Max Unit Period Tv 1034 1066 2048 Th Active Tdisp(v) 1024 1024 1024 Th Vertical

Section Blanking Tbp(v)+Tfp(v)+PWvs 10 42 1024 Th Period Th 750 844 2048 Tclk Active Tdisp(h) 640 640 640 Tclk Horizontal

Section Blanking Tbp(h)+Tfp(h)+PWhs 110 204 1408 Tclk Period Tclk 14.81 18.52 25 ns Clock Frequency Freq 40 54 70 MHz

Frame rate Frame rate F 49 60 76 Hz Note : DE mode only

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

6.4.2 Timing Digram Hsync

Pixel

N1

M

Invalid Data

Tdisp(v)

10

DE

DE

Invalid Data

RGB Data

Th

2RGB Data (Even)

39

M-1

Invalid Data

1

N

Hsync

M-2

Invalid Data11

6 5M-3

Vsync

Invalid Data

CLK

M-5

Invalid Data

M-4

7

2

Tbp(h)

PixelPixel

PixelPixel

PixelRGB Data (Odd)

12

Tbp(v)

Tclk

PixelPixel

PixelPixel

PixelPixel

PixelPixel

PixelPixel

Pixel

Pixel8

43

4

Tv

Tdisp(h)

LineLine

LineLine

LineLine

Tfp(v)

Tfp(h)

PWvs

PWhs

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

6.5 Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

Power Sequence Timing

Value Parameter Min. Typ. Max. Unit

T1 0.5 - 10 [ms] T2 0 - 10 [ms] T3 300 - - [ms] T4 100 - - [ms] T5 0 16 50 [ms] T6 - - - [ms] T7 1000 - - [ms]

Note: The values of the table are follow PSWG.

T7 T5 T2

T3

VALID DATA

T1

10%

90%

10%

90%

T4

T6 Power Supply VDD

LVDS Signal

Backlight On

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

7. Connector & Pin Assignment Physical interface is described as for the connector on module.These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT LCD Module 7.1.1 Connector Connector Name / Designation Interface Connector / Interface card Manufacturer JAE / STM Type Part Number FI-XB30SSL-HF15 / MSBKT2407P30HB Mating Housing Part Number JAE FI-X30HL 7.1.2 Pin Assignment

Pin# Signal Name Pin# Signal Name 1 RxOIN0- 2 RxOIN0+ 3 RxOIN1- 4 RxOIN1+ 5 RxOIN2- 6 RxOIN2+ 7 GND 8 RxOCLKIN- 9 RxOCLKIN+ 10 RxOIN3- 11 RxOIN3+ 12 RxEIN0- 13 RxEIN0+ 14 GND 15 RxEIN1- 16 RxEIN1+ 17 GND 18 RxEIN2- 19 RxEIN2+ 20 RxECLKIN- 21 RxECLKIN+ 22 RxEIN3- 23 RxEIN3+ 24 GND 25 GND (AGMODE+HVS) 26 NC 27 GND 28 VCC 29 VCC 30 VCC

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

7.2 Backlight Unit Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Lamp Connector / Backlight lamp Manufacturer YENONHO or CVILUX Type Part Number 35001HS-02L or CP0521S1 Mating Type Part Number 35001WR-00LS00 or CP0502SL090

7.2.1 Signal for Lamp connector

Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage (Lamp 1) Upper CN1

2 Cold1 White Low Voltage (Lamp 1)

Connector No. Pin No. Input Color Function

1 Hot1 Pink High Voltage (Lamp 2) Lower CN2

2 Cold1 White Low Voltage (Lamp 2)

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

8. Reliability Test Environment test conditions are listed as following table.

Items Required Condition Note Temperature Humidity Bias (THB) Ta= 50 , 80%RH, 300hours High Temperature Operation (HTO) Ta= 50 , 50%RH, 300hours Low Temperature Operation (LTO) Ta= 0 , 300hours High Temperature Storage (HTS) Ta= 60 , 300hours Low Temperature Storage (LTS) Ta= -20 , 300hours

Vibration Test (Non-operation)

Acceleration: 1.5 G Wave: Random Frequency: 10 - 200 - 10 Hz Sweep: 30 Minutes each Axis (X, Y, Z)

Shock Test (Non-operation)

Acceleration: 50 G Wave: Half-sine Active Time: 20 ms Direction: ±X, ±Y, ±Z (one time for each Axis)

Drop Test Height: 60 cm, package test Thermal Shock Test (TST) -20/30min, 60/30min, 100 cycles 1 On/Off Test On/10sec, Off/10sec, 30,000 cycles

Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point.

ESD (ElectroStatic Discharge) Air Discharge: ± 15KV, 150pF(330Ω ) 1sec 8 points, 25 times/ point.

2

Altitude Test Operation:10,000 ft Non-Operation:30,000 ft

Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -20 to 60, and back again. Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before power on.

Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost. Self-recoverable. No hardware failures.

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

9. Shipping Label The shipping label format is shown as below.

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29



M170EG01 VG

10. Mechanical Characteristics

AUO Con

fiden

tial F

or PROMATE In

terna

l Use

Only

/ 200

9/4/29

Documents

AUO Confidential For PROMATE Internal Use Only / 2009/4/29chuanling.net/down/M170EG01 VG.pdf · AU OPTRONICS CORPORATION Product Specification document version1.2 2/25