450 Riverside Dr • Wyalusing PA, 18853 • Phone 570-746-1888 • Fax 570-746-9286AUI-

Member of AMCADivision of Mestek

MODEL EA-22SD-EA22-

Miami-Dade HVHZ Louver • 4” Deep • 45° Dual Drainable Blades • Stationary • Extruded Aluminum Page 1

arrowunited.com

17.08

09-01-01

August 2017

In the interest of product development, Arrow United reserves the right to make changes without notice.

Item # QtyWidth Height Width Height

MullionType Location

Opening Size Louver Size Screens Union Made

Arch. / Eng.: EDR: ECN: Job:

Contractor:

Project: Date: DWN: DWG:

Louver Width (in.)

60” Max. Section

Mullion (Typ.)1¼” (Typ.)

Withstands pressures up to ±150 PSF.

Visit our Miami-Dade Listing Page for the latest NOA information:https://goo.gl/DJ5UtM

Standard Materials and Construction

Options

Notes

Test Methods

Louver Sizes

Min Panel Max Single Panel

12"W x 12"H 60”W x 96”H

FRAME: .125” thick (nominal) extruded aluminum, 6063-T52/T6 alloy. BLADE: .125” thick (nominal) extruded aluminum, 6063-T52/T6 alloy. Blades approximately 4” on centers. LOUVER FACE: Full width sill with head and blades contained within jambs. Welded construction. SCREEN: (When indicated, in a removable frame.) ½”flattenedaluminum(.051”thick), -or- ½” sq. mesh, intermediate double-crimped aluminum wire, .063” dia., -or- ¹⁸⁄16 mesh, .011” dia. aluminum wire, insect screen. FINISH: Mill

Passed the following Miami-Dade County Florida Test Protocols: • TAS (PA) 201 • TAS (PA) 202 • TAS (PA) 203

Finish - Baked Enamel, Kynar, AnodizeExtended Sill

1. Nominal deductions will be made to the opening size given.2. Approximate shipping weight is 6.0 lbs./sq.ft.

Windload requirements may limit panel sizes.

4”

Louver Height(in.)

1”(Typ.)

Not to scale.

4”

450 Riverside Dr • Wyalusing PA, 18853 • Phone 570-746-1888 • Fax 570-746-9286AUI-

Member of AMCADivision of Mestek

SD-EA22-MODEL EA-22

Miami-Dade HVHZ Louver • 4” Deep • 45° Dual Drainable Blades • Stationary • Extruded Aluminum Page 2

arrowunited.com

17.08

09-01-01

August 2017

Performance Data

Ratingsdonotincludeeffectsofascreen.

Pres

sure

Dro

p (in

. w.g

.)

Pressure Drop

Velocity (fpm) x 100 thru Free Area3 754 6 8 109

.03

.06

.05

.04

.01

.08

.07

.02

.30

.09

.10

.20

.40

.50

Intak

e

12 14 16 18 20

Intake air converted to standard air density. Tested to AMCA Standard 500-L, Figure 5.5.

Model EA-22Test Unit Size

48” x 48”

10009000

.02

.06

.04

.10

.08

.12

.16

.14

.20

.18

.22

.26

.24

.30

.28

Velocity (fpm) thru Free Area

Water Penetration

1100 1200 1300

1075 (FPM) Beginning Point of Water Penetration

Wat

er (o

z./ft

.²) F

ree

Area

- 15

Min

ute

Inte

rval

Model EA-22Test Unit Size

48” x 48”

Width (in.)

12" 18” 24” 30” 36” 42” 48” 54” 60”

Hei

ght (

in.)

12” .31 .50 .70 .90 1.09 1.29 1.48 1.68 1.87

24” .81 1.31 1.82 2.33 2.84 3.35 3.86 4.36 4.87

36” 1.30 2.12 2.94 3.77 4.59 5.41 6.23 7.05 7.87

48” 1.80 2.93 4.07 5.20 6.34 7.47 8.37 9.74 10.87

60” 2.29 3.74 5.19 6.64 8.08 9.53 10.98 12.43 13.88

72” 2.79 4.55 6.31 8.07 9.83 11.59 13.35 15.12 16.88

84” 3.28 5.36 7.43 9.51 11.58 13.65 15.73 17.80 19.88

96” 3.78 6.17 8.55 10.94 13.33 15.72 18.10 20.49 22.88

Free Area (sq.ft.)

ArrowUnitedIndustriescertifiesthattheModel EA-22 shown herein is licensed to bear the AMCA seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCACertifiedRatingsProgram.TheAMCACertifiedRatingsSealappliestoWaterPenetration and Air Performance Ratings only.

Pressure Drop: .15 in. w.g. at 1000 fpm (intake) Free Area: 8.37 sq.ft. = 52% for 48”W x 48”H sample tested in accordance with AMCA Standard 500-L.Beginning Point of Water Penetration: 1075 fpm

*

Visit our Miami-Dade Listing Page for the latest NOA information:https://goo.gl/DJ5UtM

450 Riverside Dr • Wyalusing PA, 18853 • Phone 570-746-1888 • Fax 570-746-9286AUI-

Member of AMCADivision of Mestek

MODEL EA-22SD-EA22-

Miami-Dade HVHZ Louver • 4” Deep • 45° Dual Drainable Blades • Stationary • Extruded Aluminum Page 3

arrowunited.com

17.08

09-01-01

August 2017

Installation Details

⁵⁄16” - 18 UNC x 1½” Hex head steel bolt withflatwasher,lockwasher, and nut. 4” from ends and 8” on center.

4”x3”x⅜”A36steelangle 2¾” long (2) per

mullion end.

½” x 2” A307 Hex head plated steel

boltwithflatwasher,lockwasher, and nut (2) per mullion end.

⅝”x2¼”sleeveanchor(Concrete) at head/sill.

Sealant by others.

C5 x 6.7 A36 Steel

4”

Visible Vertical Mullion Detail

2” x 2” x ¼” thick, 2” long within 4” from ends of either aluminum or A36

steel as required per load table.⁵⁄16” - 18 UNC x 1½” Hex head steel boltwithflatwasher,lockwasher,and nut. 4” from ends and 8” on

center. 4”x3”x⅜”A36steelangle2¾” long (2) per mullion end.

(2) #14 x 1¼” Hilti Tek screw

Concrete Head/Sill

½” x 2” A307 Hex head plated steel bolt withflatwasher,lockwasher,andnut(2)

per mullion end.

⅝”x2¼”sleeveanchor(1) per channel end.(1) per head & sill.

Extended Sill (Optional)

Sealant by others.

C5 x 6.7 A36 Steel4”

1¼”

2⅛”

9½”±

¼” Max.

Head/Sill Detail

2” x 2” x ¼” thick, 2” long within 4” from ends of either aluminum or A36 steel as required per load table.

(2) #14 x 1¼” Hilti Tek screw

(Concrete)⅝”x2¼”sleeveanchor at jamb.

(Masonry)⅜”x1⅞”sleeveanchor at jamb.

Red Head Dynabolt at jamb.Masonry or Concrete

Sealant by others.

4”

1¼”

¼” Max.

Jamb Detail

Visit our Miami-Dade Listing Page for the latest NOA information:https://goo.gl/DJ5UtM