Audio Video trainingen · 2019. 1. 8. · 1. Set should be plugged in and in Standby Mode. 2.1. Push “Repeat” Button during about 5 seconds, using Remote Controller. 3. Front

Samsung Training

• 2016

How to reset Soundbar & MultiRoom

Speakers

How to reset Multi-Room speakers Initialization method WAM350/550/750

1. Speaker should be plugged in and not playing music.

2. Press and hold the Internet Radio button and the Mute button

on the top panel for 5 seconds until you hear a beep.

3. Touch button of the Wireless Audio Multi-room will be blinking 2 times.

4. Press and hold the Internet Radio button for more 5 seconds

to reboot your Wireless Audio Multi-room.

5. Initialization complete.

Initialization method WAM1500/3500/5500


2. Press and hold the “+” and “-” button for 10 seconds.

3. The speaker will reboot automatically.


How to reset Multi-Room speakers Initialization method WAM6500/7500


2. Press and hold the Vol. - button and Vol. + button

on the top panel for 5 seconds until you see purple LED.

3. The speaker will reboot automatically.


How to reset Soundbar HW-F, H and J Series Initialization method Soundbar:

1. Set should be plugged in and in Standby Mode.

2.1. Push “Repeat” Button during about 5 seconds, using Remote Controller.

3. Front OLED will be Display


INIT OK

Reconnection method Soundbar and Subwoofer

1. Plug the power cords of the main unit and subwoofer into an AC wall outlet. 2. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds.

• The STANDBY indicator is turned off and the LINK indicator (Blue LED) blinks quickly. 3. While the main unit is powered off (in STANDBY mode), press and hold the (Mute) on the remote control for 5 seconds. 4. The ID SET message appears on the Soundbar's display. 5. To finalize the link, turn the main unit’s power on while the subwoofer’s Blue LED blinks.

How to reset Soundbar HW-K650 Initialization method Soundbar:


2.1. Push “Repeat” Button during about 5 seconds, using Remote Controller.

2.2. Or Push + , - Button more than 5 secons at the same time on the UNIT.



INIT OK




How to reset Soundbar HW-K850/K950 Initialization method Soundbar:


2. Press and hold the ‘Sound Control’ button 10sec, using Remote Controller.



INIT OK




How to reset Soundbar HW-M360/450 Initialization method Soundbar:


2. Press the “ VOL”(MUTE) button for 5 seconds in the remote control.



INIT OK


1. Plug the power cords of the main unit and subwoofer into an AC wall outlet.

2. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds.

• The STANDBY indicator is turned off and the LINK indicator (Blue LED) blinks quickly.

3. To finalize the link, turn the main unit’s power on while the subwoofer’s Blue LED blinks.

4. The main unit and the sub-woofer will pair automatically.

How to reset Soundbar HW-MS650 Initialization method Soundbar:


2. Press and hold the ‘Sound Control’ button 10sec, using Remote Controller.



INIT OK

How to reset Soundbar HW-N400 1/2 Initialization method Soundbar (Using the remote control):


2. Press and hold the “Play/Pause” button for more than 5 seconds by using Remote Controller.


4. If it was successful, “INIT”->”OK” will be displayed for 2 seconds and be turned off.

INIT OK

Initialization method Soundbar (Without using the remote control):

1. Set should be plugged in and switched ON.

2. Press and hold the “+” button and “-” button on Sound Bar simultaneously for 5 seconds.



INIT OK

How to pair Soundbar HW-N400 and SWA-8500S 2/2 Pairing method:

Sound Bar(Using the remote control)


2. Press and hold the “MUTE” button on the remote for more than 5 seconds.

3. If it was successful, “ID SET” will be displayed for some seconds and be turned off.

4. When the soundbar is turned on, it will start finding wireless Rear kit

Rear Kit(Sold separately, SWA-8500S)

1. You can see the ID-set button the rear side of Rear Kit.

2. When Rear Kit is turned on, press the ID-set button for 5 seconds.

3. The STANDBY indicator is turned off and the LINK indicator (Blue LED) blinks quickly.

4. The main unit and the Rear Kit will pair automatically.

How to reset Soundbar HW-N700 Initialization method Soundbar (Using the remote control):

1. Set should be plugged in and in Power ON Mode.

2. Press and hold the “Sound Control” button for more than 10 seconds by using Remote Controller.



INIT OK






INIT OK

How to reset Soundbar HW-N950 1/2 Initialization method Soundbar (Using the remote control):

1. Set should be plugged in and in Power ON Mode.

2. Press and hold the “Sound Control” button for more than 10 seconds by using Remote Controller.



INIT OK






• Things being cleared after initialization : WiFi, BT, EQ, and other uer settings.

• Subwoofer and Rear connection will not be cleared by above initialization.

• So the “IDset “ must be conducted after repair on both of Soundbar and wireless Rear/ subwoofer so as to make them auto connection on customers

hand.

• ( If subwoofer/rear speaker did not come to SVC, you need to guide the customer how to pair them)

INIT OK

How to pair Soundbar HW-N950 and Subw. + rear speakers 2/2 Pairing method:

Sound Bar(Using the remote control)


2. Press and hold the “MUTE” button on the remote for more than 5 seconds.

3. If it was successful, “ID SET” will be displayed for some seconds and be turned off.

4. When the soundbar is turned on, it will start finding wireless Rear kit

Subwoofer and Rear Speakers

1. You can see the ID-set button the rear side of Subwoofer and Rear speakers.

2. When Subwoofer and Rear speakers are turned on, press the ID-set button for 5 seconds.

3. The STANDBY indicator is turned off and the LINK indicator (Blue LED) blinks quickly.

4. The main unit Subwoofer and the Rear Speakers will pair automatically.

Thank You

Documents

Audio Video trainingen · 2019. 1. 8. · 1. Set should be plugged in and in Standby Mode. 2.1. Push “Repeat” Button during about 5 seconds, using Remote Controller. 3. Front